The Exynos5420 SoC has 3 sets of 8 pads used as data lines for the 3
MMC/SD/SDIO slots. These needs to be muxed as SD_n_DATA instead of a
GPIO or external interrupt to allow the MMC controller to communicate
with the attached cards or SDIO devices.
Which data lines needs to be muxed as SD_n_DATA depends on the bus
width used for data transfer:
* bus-width = <1> needs SD_n_DATA[0]
* bus-width = <4> needs SD_n_DATA[0-3]
* bus-width = <8> needs SD_n_DATA[0-7]
The Exynos5250-pinctrl.dtsi file that defines the groups of pins has
SD_n_DATA[0] muxed for both sdn_bus1 and sdn_bus4 so just one of them
needs to be included in the device node's pinctrl property.
But Exynos5420-pinctrl has a different definition and only includes
SD_n_DATA[1-3] for sdn_bus4. So for a bus-width = <4>, both sdn_bus1
and sdn_bus4 have to be in the dev pinctrl to mux all the needed pads.
It seems all Exynos5420 boards had just cargo cult the pinctrl lines
assuming that sdn_bus4 also included SD_n_DATA[0] and it only works
because the bootloader muxes the pads correctly. But that is not the
case for the devices not used by the bootloader such as WiFi modules.
Add sdn_bus1 too in the nodes pinctrl to not rely on the bootloader.
Suggested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds reset-gpios property to the eMMC slot, so the MMC driver
is able to properly reset eMMC card on system restart and thus fixes
system hang on software reboot.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Last 22 MiB is RAM is reserved by secure monitor code and cannot be
accessed from Linux kernel, so adjust total RAM size to 0x7EA00000
(2 GiB - 22 MiB). This fixes random 'imprecise kernel abort' kernel
failures.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The odroid-xu3 has 4 INA231 current sensors on board which can be
accessed from the Linux via the hwmon interface.
There is one sensor for each of these power rails:
- A15 cluster: VDD_ARM
- A7 cluster: VDD_KFC
- GPU: VDD_G3D
- memory: VDD_MEM
In addition to adding the sensors, LDO26 from the PMIC needs to be
enabled because it's powering these sensor.
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add DTS for the Hardkernel Odroid XU3. The name of the DTS file is
kept the same as the vendors naming, which means it's prefixed with
exynos5422 instead of exynos5800 as the SoC name even though it
includes the exyno5800 dtsi.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Javier Martinez Canillas