There are a few Ocelot chips that can contain SGPIO logic, but can be
controlled externally. Specifically the VSC7511, 7512, 7513, and 7514. In
the externally controlled configurations these registers are not
memory-mapped.
Add support for these non-memory-mapped configurations.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20220905162132.2943088-6-colin.foster@in-advantage.com
As the commit message suggests, this simply adds the ability to select
SGPIO pinctrl as a module. This becomes more practical when the SGPIO
hardware exists on an external chip, controlled indirectly by I2C or SPI.
This commit enables that level of control.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20220905162132.2943088-5-colin.foster@in-advantage.com
Since recently, the kernel is nagging about mutable irq_chips:
[ 4.967050] gpio gpiochip1: (e2004190.gpio-input): not an immutable chip, please consider fixing it!
Drop the unneeded copy, flag it as IRQCHIP_IMMUTABLE, add the new
helper functions and call the appropriate gpiolib functions.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220428111622.1395831-1-michael@walle.cc
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
No core changes this time. Just new driver code and improvements!
New drivers:
- New driver for the Broadcom BCM4908 SoC.
- New subdriver for Tesla FSD (Full Self Driving) SoC, a
derivative of the Samsung Exynos pin control driver.
- New driver for the Amlogic Meson S4 SoC.
- New driver for the Sunplus SP7021 SoC.
- New driver for the Microsemi Ocelot family ServalT SoC.
- New subdriver for Intel Alder Lake-M SoC.
- New subdriver for Intel Ice Lake-N SoC, including PCH support.
- New subdriver for Renesas R8A779F0 SoC.
- New subdriver for Mediatek MT8186 SoC.
- New subdriver for NXP Freescale i.MX93 SoC.
- New driver for Nuvoton WPCM450 SoC.
- New driver for Qualcomm SC8280XP SoC.
Improvements:
- Wakeup support on Samsung Exynos850 and ExynosAutov9.
- Serious and voluminous maintenance cleanup and refactoring in
the Renesas drivers. Mainly sharing similar data between the
different SoC subdrivers.
- Qualcomm SM8450 EGPIO support.
- Drive strength support on the Mediatek MT8195.
- Add some missing groups and functions to the Ralink RT2880.
-----BEGIN PGP SIGNATURE-----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=TY4V
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"No core changes this time. Just new driver code and improvements!
New drivers:
- New driver for the Broadcom BCM4908 SoC.
- New subdriver for Tesla FSD (Full Self Driving) SoC, a derivative
of the Samsung Exynos pin control driver.
- New driver for the Amlogic Meson S4 SoC.
- New driver for the Sunplus SP7021 SoC.
- New driver for the Microsemi Ocelot family ServalT SoC.
- New subdriver for Intel Alder Lake-M SoC.
- New subdriver for Intel Ice Lake-N SoC, including PCH support.
- New subdriver for Renesas R8A779F0 SoC.
- New subdriver for Mediatek MT8186 SoC.
- New subdriver for NXP Freescale i.MX93 SoC.
- New driver for Nuvoton WPCM450 SoC.
- New driver for Qualcomm SC8280XP SoC.
Improvements:
- Wakeup support on Samsung Exynos850 and ExynosAutov9.
- Serious and voluminous maintenance cleanup and refactoring in the
Renesas drivers. Mainly sharing similar data between the different
SoC subdrivers.
- Qualcomm SM8450 EGPIO support.
- Drive strength support on the Mediatek MT8195.
- Add some missing groups and functions to the Ralink RT2880"
* tag 'pinctrl-v5.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (188 commits)
pinctrl: mediatek: common-v1: fix semicolon.cocci warnings
pinctrl: nuvoton: wpcm450: Fix build error without OF
pinctrl: qcom-pmic-gpio: Add support for pm8450
dt-bindings: pinctrl: aspeed: Update gfx node in example
dt-bindings: pinctrl: rt2880: add missing pin groups and functions
pinctrl: ingenic: Fix regmap on X series SoCs
pinctrl: nuvoton: Fix return value check in wpcm450_gpio_register()
pinctrl: nuvoton: wpcm450: off by one in wpcm450_gpio_register()
pinctrl: nuvoton: wpcm450: select GENERIC_PINCTRL_GROUPS
pinctrl: nuvoton: Fix sparse warning
pinctrl: mediatek: mt8186: Account for probe refactoring
pinctrl: mediatek: common-v1: Commonize spec_ies_smt_set callback
pinctrl: mediatek: common-v1: Commonize spec_pupd callback
pinctrl: mediatek: common-v1: Use common probe function
pinctrl: mediatek: common-v1: Add common probe function
pinctrl: mediatek: paris: Unify probe function by using OF match data
pinctrl/rockchip: Add missing of_node_put() in rockchip_pinctrl_probe
pinctrl: nomadik: Add missing of_node_put() in nmk_pinctrl_probe
pinctrl: berlin: fix error return code of berlin_pinctrl_build_state()
pinctrl: qcom: Introduce sc8280xp TLMM driver
...
Right now, when a gpio value is set, the actual hardware pin gets set
asynchronously. When linux write the output register, it takes some time
until it is actually propagated to the output shift registers. If that
output port is connected to an I2C mux for example, the linux driver
assumes the I2C bus is already switched although it is not.
Fortunately, there is a single shot mode with a feedback: you can
trigger the single shot and the hardware will clear that bit once it has
finished the clocking and strobed the load signal of the shift
registers. This can take a considerable amount of time though.
Measuremens have shown that it takes up to a whole burst cycle gap which
is about 50ms on the largest setting. Therefore, we have to mark the
output bank as sleepable. To avoid unnecessary waiting, just trigger the
single shot if the value was actually changed.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220226204507.2511633-6-michael@walle.cc
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make sgpio_output_set() return an error value. Don't just ignore the
return value of any regmap access but propagate it to our callers. Even
if the accesses never fail, this is a preparation patch to add single
shot mode where we need to poll a bit and thus we might get -ETIMEDOUT.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220226204507.2511633-5-michael@walle.cc
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert sgpio_clrsetbits() to use regmap_update_bits() and drop the
spinlocks because regmap already takes care of the locking.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220226204507.2511633-4-michael@walle.cc
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The interrupt ack register has the usual "write one to clear" semantics.
No read-modify-write is required here.
This is also a preparation patch to change the sgpio_clrsetbits() to use
regmap_update_bits() which don't write the value if it is not changed.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220226204507.2511633-3-michael@walle.cc
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Protect any RMW access to the registers by a spinlock.
Fixes: 7e5ea974e6 ("pinctrl: pinctrl-microchip-sgpio: Add pinctrl driver for Microsemi Serial GPIO")
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220226204507.2511633-2-michael@walle.cc
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Initially the driver accessed the registers using u32 __iomem but then
in the blamed commit it changed it to use regmap. The problem is that now
the offset of the registers is not calculated anymore at word offset but
at byte offset. Therefore make sure to multiply the offset with word size.
Acked-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Reviewed-by: Colin Foster <colin.foster@in-advantage.com>
Fixes: 2afbbab45c ("pinctrl: microchip-sgpio: update to support regmap")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220131085201.307031-1-horatiu.vultur@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On lan966x platform when the switch gets reseted then also the sgpio
gets reseted. The fix for this is to extend also the sgpio driver to
call the reset driver which will be reseted only once by the first
driver that is probed.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Steen Hegelund <steen.hegelund@microchip.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20211018085754.1066056-3-horatiu.vultur@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Wherever possible, replace constructs that match either
generic_handle_irq(irq_find_mapping()) or
generic_handle_irq(irq_linear_revmap()) to a single call to
generic_handle_domain_irq().
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
device_for_each_child_node() bumps a reference counting of a returned variable.
We have to balance it whenever we return to the caller.
Fixes: 7e5ea974e6 ("pinctrl: pinctrl-microchip-sgpio: Add pinctrl driver for Microsemi Serial GPIO")
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210606191940.29312-1-andy.shevchenko@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes using a wrong register offset when configuring an IRQ
trigger type.
Fixes: be2dc859ab ("pinctrl: pinctrl-microchip-sgpio: Add irq support (for sparx5)")
Reported-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20210203123825.611576-1-lars.povlsen@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds 'interrupt-controller' features for the signals available on
the Microchip SGPIO controller, however only for controller versions
on the Sparx5 platform (or later).
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Link: https://lore.kernel.org/r/20201209142753.683208-2-lars.povlsen@microchip.com
[Select GPIOLIB_IRQCHIP in Kconfig]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix the following sparse warnings:
drivers/pinctrl/pinctrl-microchip-sgpio.c:63:31: warning: symbol 'properties_luton' was not declared. Should it be static?
drivers/pinctrl/pinctrl-microchip-sgpio.c:68:31: warning: symbol 'properties_ocelot' was not declared. Should it be static?
drivers/pinctrl/pinctrl-microchip-sgpio.c:73:31: warning: symbol 'properties_sparx5' was not declared. Should it be static?
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1606218173-3722-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a pinctrl driver for the Microsemi/Microchip Serial GPIO
(SGPIO) device used in various SoC's.
The driver is added as a pinctrl driver, albeit only having just GPIO
support currently. The hardware supports other functions that will be
added following.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Link: https://lore.kernel.org/r/20201113145151.68900-3-lars.povlsen@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Colin Foster