This patch adds support for SMMUs implementing the ARM System MMU
architecture versions 1 or 2. Both arm and arm64 are supported, although
the v7s descriptor format is not used.
Cc: Rob Herring <robherring2@gmail.com>
Cc: Andreas Herrmann <andreas.herrmann@calxeda.com>
Cc: Olav Haugan <ohaugan@codeaurora.org>
Cc: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Acked-by: Andreas Herrmann <andreas.herrmann@calxeda.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Calling clk_set_min_rate() is no better than just calling
clk_set_rate() because MSM clock code already takes care of
calling the min_rate ops if the clock really needs
clk_set_min_rate() called on it.
Cc: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Add calls to clk_prepare and unprepare so that MSM can migrate to
the common clock framework. We never unprepare the clocks until
driver remove because the clocks are enabled and disabled in irq
context. Finer grained power management is possible in the future
via runtime power management techniques.
Cc: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
printk supports using %pa for phys_addr_t and
%zx for size_t so use those instead of %lx and
casts to unsigned long.
Other miscellaneous changes around this:
Always use 0x%zx for size instead of one use of decimal.
Coalesce format and align arguments.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
If we use a large mapping, the expectation is that only unmaps from
the first pte in the superpage are supported. Unmaps from offsets
into the superpage should fail (ie. return zero sized unmap). In the
current code, unmapping from an offset clears the size of the full
mapping starting from an offset. For instance, if we map a 16k
physically contiguous range at IOVA 0x0 with a large page, then
attempt to unmap 4k at offset 12k, 4 ptes are cleared (12k - 28k) and
the unmap returns 16k unmapped. This potentially incorrectly clears
valid mappings and confuses drivers like VFIO that use the unmap size
to release pinned pages.
Fix by refusing to unmap from offsets into the page.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <joro@8bytes.org>
The IOMMU pagetables can have up to 6 levels, but the code
in free_pagetable() only releases the first 3 levels. Fix
this leak by releasing all levels.
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
iommu_map splits requests into pages that the iommu driver reports
that it can handle. The iommu_unmap path does not do the same. This
can cause problems not only from callers that might expect the same
behavior as the map path, but even from the failure path of iommu_map,
should it fail at a point where it has mapped and needs to unwind a
set of pages that the iommu driver cannot handle directly. amd_iommu,
for example, will BUG_ON if asked to unmap a non power of 2 size.
Fix this by extracting and generalizing the sizing code from the
iommu_map path and use it for both map and unmap.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
If a device is multifunction and does not have ACS enabled then we
assume that the entire package lacks ACS and use function 0 as the
base of the group. The PCIe spec however states that components are
permitted to implement ACS on some, none, or all of their applicable
functions. It's therefore conceivable that function 0 may be fully
independent and support ACS while other functions do not. Instead
use the lowest function of the slot that does not have ACS enabled
as the base of the group. This may be the current device, which is
intentional. So long as we use a consistent algorithm, all the
non-ACS functions will be grouped together and ACS functions will
get separate groups.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
This patch fixes the checkpatch warnings in omap iommu
code, most of them are related to broken strings.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Fixed the following printk format warnings for dma_addr_t
for OMAP IOMMU.
drivers/iommu/omap-iommu.c: In function 'omap_iommu_iova_to_phys':
drivers/iommu/omap-iommu.c:1238:4: warning: format '%lx' expects type 'long unsigned int', but argument 4 has type 'dma_addr_t'
drivers/iommu/omap-iommu.c:1245:4: warning: format '%lx' expects type 'long unsigned int', but argument 4 has type 'dma_addr_t'
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
In intel vt-d spec , chapter 8.1 , DMA Remapping Reporting Structure.
In the end of the table, it says:
Remapping Structures[]
-
A list of structures. The list will contain one or
more DMA Remapping Hardware Unit Definition
(DRHD) structures, and zero or more Reserved
Memory Region Reporting (RMRR) and Root Port
ATS Capability Reporting (ATSR) structures.
These structures are described below.
So, there should be at least one DRHD structure in DMA Remapping
reporting table. If there is no DRHD found, a warning is necessary.
Signed-off-by: Li, Zhen-Hua <zhen-hual@hp.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
This triggers on a MacBook Pro.
See https://bugzilla.redhat.com/show_bug.cgi?id=948262 for
the problem report.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
The enables VFIO on the pSeries platform, enabling user space
programs to access PCI devices directly.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Cc: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This initializes IOMMU groups based on the IOMMU configuration
discovered during the PCI scan on POWERNV (POWER non virtualized)
platform. The IOMMU groups are to be used later by the VFIO driver,
which is used for PCI pass through.
It also implements an API for mapping/unmapping pages for
guest PCI drivers and providing DMA window properties.
This API is going to be used later by QEMU-VFIO to handle
h_put_tce hypercalls from the KVM guest.
The iommu_put_tce_user_mode() does only a single page mapping
as an API for adding many mappings at once is going to be
added later.
Although this driver has been tested only on the POWERNV
platform, it should work on any platform which supports
TCE tables. As h_put_tce hypercall is received by the host
kernel and processed by the QEMU (what involves calling
the host kernel again), performance is not the best -
circa 220MB/s on 10Gb ethernet network.
To enable VFIO on POWER, enable SPAPR_TCE_IOMMU config
option and configure VFIO as required.
Cc: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add functionality to check the availability of the AMD IOMMU Performance
Counters and export this functionality to other core drivers, such as in this
case, a perf AMD IOMMU PMU. This feature is not bound to any specific AMD
family/model other than the presence of the IOMMU with P-C enabled.
The AMD IOMMU P-C support static counting only at this time.
Signed-off-by: Steven Kinney <steven.kinney@amd.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1370466709-3212-2-git-send-email-suravee.suthikulpanit@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Current multiple-MSI implementation does not take into account actual
number of requested MSIs and always rounds that number to a larger
power-of-two value. Yet, the number of MSIs a PCI device could send (and
therefore the number of messages a device driver could request) may be
smaller. As result, resources allocated for extra MSIs are just wasted.
This update takes advantage of 'msi_desc::nvec_used' field introduced with
generic MSI code to track the number of requested and used MSIs. As
result, resources associated with interrupts are conserved. Of those
resources most noticeable are x86 interrupt vectors.
The initial version of this fix also conserved IRTEs, but Jan noticed that
a malfunctioning PCI device might send a message number it did not claim
and thus refer to an IRTE it does not own. To avoid this security hole,
as many IRTEs are reserved as the device could possibly send.
[bhelgaas: changelog, rename to "nvec_used"]
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The updates are mostly about the x86 IOMMUs this time. Exceptions are
the groundwork for the PAMU IOMMU from Freescale (for a PPC platform)
and an extension to the IOMMU group interface. On the x86 side this
includes a workaround for VT-d to disable interrupt remapping on broken
chipsets. On the AMD-Vi side the most important new feature is a kernel
command-line interface to override broken information in IVRS ACPI
tables and get interrupt remapping working this way. Besides that there
are small fixes all over the place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=MVc/
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"The updates are mostly about the x86 IOMMUs this time.
Exceptions are the groundwork for the PAMU IOMMU from Freescale (for a
PPC platform) and an extension to the IOMMU group interface.
On the x86 side this includes a workaround for VT-d to disable
interrupt remapping on broken chipsets. On the AMD-Vi side the most
important new feature is a kernel command-line interface to override
broken information in IVRS ACPI tables and get interrupt remapping
working this way.
Besides that there are small fixes all over the place."
* tag 'iommu-updates-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (24 commits)
iommu/tegra: Fix printk formats for dma_addr_t
iommu: Add a function to find an iommu group by id
iommu/vt-d: Remove warning for HPET scope type
iommu: Move swap_pci_ref function to drivers/iommu/pci.h.
iommu/vt-d: Disable translation if already enabled
iommu/amd: fix error return code in early_amd_iommu_init()
iommu/AMD: Per-thread IOMMU Interrupt Handling
iommu: Include linux/err.h
iommu/amd: Workaround for ERBT1312
iommu/amd: Document ivrs_ioapic and ivrs_hpet parameters
iommu/amd: Don't report firmware bugs with cmd-line ivrs overrides
iommu/amd: Add ioapic and hpet ivrs override
iommu/amd: Add early maps for ioapic and hpet
iommu/amd: Extend IVRS special device data structure
iommu/amd: Move add_special_device() to __init
iommu: Fix compile warnings with forward declarations
iommu/amd: Properly initialize irq-table lock
iommu/amd: Use AMD specific data structure for irq remapping
iommu/amd: Remove map_sg_no_iommu()
iommu/vt-d: add quirk for broken interrupt remapping on 55XX chipsets
...
Fix printk formats for dma_addr_t:
drivers/iommu/tegra-smmu.c: In function 'smmu_iommu_iova_to_phys':
>> drivers/iommu/tegra-smmu.c:774:2: warning: format '%lx' expects argument of type 'long unsigned int', but argument 4 has type 'dma_addr_t' [-Wformat]
--
drivers/iommu/tegra-gart.c: In function 'gart_iommu_iova_to_phys':
>> drivers/iommu/tegra-gart.c:298:3: warning: format '%lx' expects argument of type 'long unsigned int', but argument 3 has type 'dma_addr_t' [-Wformat]
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Pull x86 mm changes from Ingo Molnar:
"Misc smaller changes all over the map"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/iommu/dmar: Remove warning for HPET scope type
x86/mm/gart: Drop unnecessary check
x86/mm/hotplug: Put kernel_physical_mapping_remove() declaration in CONFIG_MEMORY_HOTREMOVE
x86/mm/fixmap: Remove unused FIX_CYCLONE_TIMER
x86/mm/numa: Simplify some bit mangling
x86/mm: Re-enable DEBUG_TLBFLUSH for X86_32
x86/mm/cpa: Cleanup split_large_page() and its callee
x86: Drop always empty .text..page_aligned section
As IOMMU groups are exposed to the user space by their numbers,
the user space can use them in various kernel APIs so the kernel
might need an API to find a group by its ID.
As an example, QEMU VFIO on PPC64 platform needs it to associate
a logical bus number (LIOBN) with a specific IOMMU group in order
to support in-kernel handling of DMA map/unmap requests.
The patch adds the iommu_group_get_by_id(id) function which performs
such search.
v2: fixed reference counting.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
ACPI_DMAR_SCOPE_TYPE_HPET is parsed by ir_parse_ioapic_hpet_scope() and
should not be flagged as an unsupported type.
Signed-off-by: Linn Crosetto <linn@hp.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
The swap_pci_ref function is used by the IOMMU API code for
swapping pci device pointers, while determining the iommu
group for the device.
Currently this function was being implemented for different
IOMMU drivers. This patch moves the function to a new file,
drivers/iommu/pci.h so that the implementation can be
shared across various IOMMU drivers.
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
This patch disables translation(dma-remapping) before its initialization
if it is already enabled.
This is needed for kexec/kdump boot. If dma-remapping is enabled in the
first kernel, it need to be disabled before initializing its page table
during second kernel boot. Wei Hu also reported that this is needed
when second kernel boots with intel_iommu=off.
Basically iommu->gcmd is used to know whether translation is enabled or
disabled, but it is always zero at boot time even when translation is
enabled since iommu->gcmd is initialized without considering such a
case. Therefor this patch synchronizes iommu->gcmd value with global
command register when iommu structure is allocated.
Signed-off-by: Takao Indoh <indou.takao@jp.fujitsu.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Fix to return -ENOMEM int the memory alloc error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
In the current interrupt handling scheme, there are as many threads as
the number of IOMMUs. Each thread is created and assigned to an IOMMU at
the time of registering interrupt handlers (request_threaded_irq).
When an IOMMU HW generates an interrupt, the irq handler (top half) wakes up
the corresponding thread to process event and PPR logs of all IOMMUs
starting from the 1st IOMMU.
In the system with multiple IOMMU,this handling scheme complicates the
synchronization of the IOMMU data structures and status registers as
there could be multiple threads competing for the same IOMMU while
the other IOMMU could be left unhandled.
To simplify, this patch is proposing a different interrupt handling scheme
by having each thread only managing interrupts of the corresponding IOMMU.
This can be achieved by passing the struct amd_iommu when registering the
interrupt handlers. This structure is unique for each IOMMU and can be used
by the bottom half thread to identify the IOMMU to be handled instead
of calling for_each_iommu. Besides this also eliminate the needs to lock
the IOMMU for processing event and PPR logs.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Work around an IOMMU hardware bug where clearing the
EVT_INT or PPR_INT bit in the status register may race with
the hardware trying to set it again. When not handled the
bit might not be cleared and we lose all future event or ppr
interrupts.
Reported-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <joro@8bytes.org>
When the IVRS entries for IOAPIC and HPET are overridden on
the kernel command line, a problem detected in the check
function might not be a firmware bug anymore. So disable
the firmware bug reporting if the user provided valid
ivrs_ioapic or ivrs_hpet entries on the command line.
Reviewed-by: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Add two new kernel commandline parameters ivrs_ioapic and
ivrs_hpet to override the Id->DeviceId mapping from the IVRS
ACPI table. This can be used to work around broken BIOSes to
get interrupt remapping working on AMD systems.
Tested-by: Borislav Petkov <bp@suse.de>
Tested-by: Suravee Suthikulanit <suravee.suthikulpanit@amd.com>
Reviewed-by: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
This is needed in a later patch were ioapic_map and hpet_map
entries are created before the slab allocator is initialized
(and thus add_special_device() can't be used).
Reviewed-by: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
This patch extends the devid_map data structure to allow
ioapic and hpet entries in ivrs to be overridden on the
kernel command line.
Reviewed-by: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
The function is only called by other __init functions, so it
can be moved to __init too.
Reviewed-by: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
For compatibility reasons the irq remapping code for the AMD
IOMMU used the same per-irq data structure as the Intel
implementation. Now that support for the AMD specific data
structure is upstream we can use this one instead.
Reviewed-by: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
This function was intended as a fall-back if the map_sg
function is called for a device not mapped by the IOMMU.
Since the AMD IOMMU driver uses per-device dma_ops this can
never happen. So this function isn't needed anymore.
Reviewed-by: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
A few years back intel published a spec update:
http://www.intel.com/content/dam/doc/specification-update/5520-and-5500-chipset-ioh-specification-update.pdf
For the 5520 and 5500 chipsets which contained an errata (specificially errata
53), which noted that these chipsets can't properly do interrupt remapping, and
as a result the recommend that interrupt remapping be disabled in bios. While
many vendors have a bios update to do exactly that, not all do, and of course
not all users update their bios to a level that corrects the problem. As a
result, occasionally interrupts can arrive at a cpu even after affinity for that
interrupt has be moved, leading to lost or spurrious interrupts (usually
characterized by the message:
kernel: do_IRQ: 7.71 No irq handler for vector (irq -1)
There have been several incidents recently of people seeing this error, and
investigation has shown that they have system for which their BIOS level is such
that this feature was not properly turned off. As such, it would be good to
give them a reminder that their systems are vulnurable to this problem. For
details of those that reported the problem, please see:
https://bugzilla.redhat.com/show_bug.cgi?id=887006
[ Joerg: Removed CONFIG_IRQ_REMAP ifdef from early-quirks.c ]
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Prarit Bhargava <prarit@redhat.com>
CC: Don Zickus <dzickus@redhat.com>
CC: Don Dutile <ddutile@redhat.com>
CC: Bjorn Helgaas <bhelgaas@google.com>
CC: Asit Mallick <asit.k.mallick@intel.com>
CC: David Woodhouse <dwmw2@infradead.org>
CC: linux-pci@vger.kernel.org
CC: Joerg Roedel <joro@8bytes.org>
CC: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: Arkadiusz Miśkiewicz <arekm@maven.pl>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Each iommu window can have access permissions associated with it. Extended the
window_enable API to incorporate window access permissions.
In case of PAMU each window can have its specific set of permissions.
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
This is required in case of PAMU, as it can support a window size of up
to 64G (even on 32bit).
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Current driver does not clear the IOMMU event log interrupt bit
in the IOMMU status register after processing an interrupt.
This causes the IOMMU hardware to generate event log interrupt only once.
This has been observed in both IOMMU v1 and V2 hardware.
This patch clears the bit by writing 1 to bit 1 of the IOMMU
status register (MMIO Offset 2020h)
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Here are some fixes which have collected since Linux v3.9-rc1. The most
important one fixes a long-standing regressen which make re-hotplugged
devices unusable when AMD IOMMU is used. The other patches fix build
issues (build regression on OMAP and a section mismatch). One patch just
removes a duplicate header include.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=/K5U
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"Here are some fixes which have collected since Linux v3.9-rc1.
The most important one fixes a long-standing regressen which make
re-hotplugged devices unusable when AMD IOMMU is used.
The other patches fix build issues (build regression on OMAP and a
section mismatch). One patch just removes a duplicate header include."
* tag 'iommu-fixes-v3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Make sure dma_ops are set for hotplug devices
x86, io_apic: remove duplicated include from irq_remapping.c
iommu: OMAP: build only on OMAP2+
amd_iommu_init: remove __init from amd_iommu_erratum_746_workaround
There is a bug introduced with commit 27c2127 that causes
devices which are hot unplugged and then hot-replugged to
not have per-device dma_ops set. This causes these devices
to not function correctly. Fixed with this patch.
Cc: stable@vger.kernel.org
Reported-by: Andreas Degert <andreas.degert@googlemail.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Change to remove local PCI_BUS() define and use the new PCI_BUS_NUM()
interface from PCI.
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
When there is a dmar irq, dmar_fault is called and all of the fields
in FSTS are cleared. But ICE/IQE/ITE should not be cleared here,
they need to be processed and cleared in function qi_check_fault.
[Minor cleanup by Joerg Roedel]
Signed-off-by: Li, Zhen-Hua <zhen-hual@hp.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
The OMAP IOMMU driver intentionally fails to build on OMAP1
platforms, so we should not allow enabling it there.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: iommu@lists.linux-foundation.org
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
commit 318fe78 ("IOMMU, AMD Family15h Model10-1Fh erratum 746 Workaround")
added amd_iommu_erratum_746_workaround and it's marked as __init, which is wrong
WARNING: drivers/iommu/built-in.o(.text+0x639c): Section mismatch in reference from the function iommu_init_pci() to the function .init.text:amd_iommu_erratum_746_workaround()
The function iommu_init_pci() references
the function __init amd_iommu_erratum_746_workaround().
This is often because iommu_init_pci lacks a __init
annotation or the annotation of amd_iommu_erratum_746_workaround is wrong.
Signed-off-by: Nikola Pajkovsky <npajkovs@redhat.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
The number of DMA fault reasons in intel's document are from 1
to 0xD, but in dmar.c fault reason 0xD is not printed out.
In this document:
"Intel Virtualization Technology for Directed I/O Architecture Specification"
http://download.intel.com/technology/computing/vptech/Intel(r)_VT_for_Direct_IO.pdf
Chapter 4. Support For Device-IOTLBs
Table 6. Unsuccessful Translated Requests
There is fault reason for 0xD not listed in kernel:
Present context-entry used to process translation request
specifies blocking of Translation Requests (Translation Type (T)
field value not equal to 01b).
This patch adds reason 0xD as well.
Signed-off-by: Li, Zhen-Hua <zhen-hual@hp.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Donald Dutile <ddutile@redhat.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Hannes Reinecke <hare@suse.de>
Link: http://lkml.kernel.org/r/1362537797-6034-1-git-send-email-zhen-hual@hp.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull vfs pile (part one) from Al Viro:
"Assorted stuff - cleaning namei.c up a bit, fixing ->d_name/->d_parent
locking violations, etc.
The most visible changes here are death of FS_REVAL_DOT (replaced with
"has ->d_weak_revalidate()") and a new helper getting from struct file
to inode. Some bits of preparation to xattr method interface changes.
Misc patches by various people sent this cycle *and* ocfs2 fixes from
several cycles ago that should've been upstream right then.
PS: the next vfs pile will be xattr stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
saner proc_get_inode() calling conventions
proc: avoid extra pde_put() in proc_fill_super()
fs: change return values from -EACCES to -EPERM
fs/exec.c: make bprm_mm_init() static
ocfs2/dlm: use GFP_ATOMIC inside a spin_lock
ocfs2: fix possible use-after-free with AIO
ocfs2: Fix oops in ocfs2_fast_symlink_readpage() code path
get_empty_filp()/alloc_file() leave both ->f_pos and ->f_version zero
target: writev() on single-element vector is pointless
export kernel_write(), convert open-coded instances
fs: encode_fh: return FILEID_INVALID if invalid fid_type
kill f_vfsmnt
vfs: kill FS_REVAL_DOT by adding a d_weak_revalidate dentry op
nfsd: handle vfs_getattr errors in acl protocol
switch vfs_getattr() to struct path
default SET_PERSONALITY() in linux/elf.h
ceph: prepopulate inodes only when request is aborted
d_hash_and_lookup(): export, switch open-coded instances
9p: switch v9fs_set_create_acl() to inode+fid, do it before d_instantiate()
9p: split dropping the acls from v9fs_set_create_acl()
...
Besides some fixes and cleanups in the code there are three more
important changes to point out this time:
* New IOMMU driver for the ARM SHMOBILE platform
* An IOMMU-API extension for non-paging IOMMUs (required for
upcoming PAMU driver)
* Rework of the way the Tegra IOMMU driver accesses its
registetrs - register windows are easier to extend now.
There are also a few changes to non-iommu code, but that is acked by the
respective maintainers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=G4Ot
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU Updates from Joerg Roedel:
"Besides some fixes and cleanups in the code there are three more
important changes to point out this time:
* New IOMMU driver for the ARM SHMOBILE platform
* An IOMMU-API extension for non-paging IOMMUs (required for
upcoming PAMU driver)
* Rework of the way the Tegra IOMMU driver accesses its
registetrs - register windows are easier to extend now.
There are also a few changes to non-iommu code, but that is acked by
the respective maintainers."
* tag 'iommu-updates-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (23 commits)
iommu/tegra: assume CONFIG_OF in SMMU driver
iommu/tegra: assume CONFIG_OF in gart driver
iommu/amd: Remove redundant NULL check before dma_ops_domain_free().
iommu/amd: Initialize device table after dma_ops
iommu/vt-d: Zero out allocated memory in dmar_enable_qi
iommu/tegra: smmu: Fix incorrect mask for regbase
iommu/exynos: Make exynos_sysmmu_disable static
ARM: mach-shmobile: r8a7740: Add IPMMU device
ARM: mach-shmobile: sh73a0: Add IPMMU device
ARM: mach-shmobile: sh7372: Add IPMMU device
iommu/shmobile: Add iommu driver for Renesas IPMMU modules
iommu: Add DOMAIN_ATTR_WINDOWS domain attribute
iommu: Add domain window handling functions
iommu: Implement DOMAIN_ATTR_PAGING attribute
iommu: Check for valid pgsize_bitmap in iommu_map/unmap
iommu: Make sure DOMAIN_ATTR_MAX is really the maximum
iommu/tegra: smmu: Change SMMU's dependency on ARCH_TEGRA
iommu/tegra: smmu: Use helper function to check for valid register offset
iommu/tegra: smmu: Support variable MMIO ranges/blocks
iommu/tegra: Add missing spinlock initialization
...
Pull drm merge from Dave Airlie:
"Highlights:
- TI LCD controller KMS driver
- TI OMAP KMS driver merged from staging
- drop gma500 stub driver
- the fbcon locking fixes
- the vgacon dirty like zebra fix.
- open firmware videomode and hdmi common code helpers
- major locking rework for kms object handling - pageflip/cursor
won't block on polling anymore!
- fbcon helper and prime helper cleanups
- i915: all over the map, haswell power well enhancements, valleyview
macro horrors cleaned up, killing lots of legacy GTT code,
- radeon: CS ioctl unification, deprecated UMS support, gpu reset
rework, VM fixes
- nouveau: reworked thermal code, external dp/tmds encoder support
(anx9805), fences sleep instead of polling,
- exynos: all over the driver fixes."
Lovely conflict in radeon/evergreen_cs.c between commit de0babd60d
("drm/radeon: enforce use of radeon_get_ib_value when reading user cmd")
and the new changes that modified that evergreen_dma_cs_parse()
function.
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (508 commits)
drm/tilcdc: only build on arm
drm/i915: Revert hdmi HDP pin checks
drm/tegra: Add list of framebuffers to debugfs
drm/tegra: Fix color expansion
drm/tegra: Split DC_CMD_STATE_CONTROL register write
drm/tegra: Implement page-flipping support
drm/tegra: Implement VBLANK support
drm/tegra: Implement .mode_set_base()
drm/tegra: Add plane support
drm/tegra: Remove bogus tegra_framebuffer structure
drm: Add consistency check for page-flipping
drm/radeon: Use generic HDMI infoframe helpers
drm/tegra: Use generic HDMI infoframe helpers
drm: Add EDID helper documentation
drm: Add HDMI infoframe helpers
video: Add generic HDMI infoframe helpers
drm: Add some missing forward declarations
drm: Move mode tables to drm_edid.c
drm: Remove duplicate drm_mode_cea_vic()
gma500: Fix n, m1 and m2 clock limits for sdvo and lvds
...
Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers all
over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
If you need me to provide a merged tree to handle these resolutions,
please let me know.
Other than those patches, there's not much here, some minor fixes and
updates.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmV0cACgkQMUfUDdst+yncCQCfbmnQZju7kzWXk6PjdFuKspT9
weAAoMCzcAtEzzc4LXuUxxG/sXBVBCjW
=yWAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
Pull x86/apic changes from Ingo Molnar:
"Main changes:
- Multiple MSI support added to the APIC, PCI and AHCI code - acked
by all relevant maintainers, by Alexander Gordeev.
The advantage is that multiple AHCI ports can have multiple MSI
irqs assigned, and can thus spread to multiple CPUs.
[ Drivers can make use of this new facility via the
pci_enable_msi_block_auto() method ]
- x86 IOAPIC code from interrupt remapping cleanups from Joerg
Roedel:
These patches move all interrupt remapping specific checks out of
the x86 core code and replaces the respective call-sites with
function pointers. As a result the interrupt remapping code is
better abstraced from x86 core interrupt handling code.
- Various smaller improvements, fixes and cleanups."
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
x86/intel/irq_remapping: Clean up x2apic opt-out security warning mess
x86, kvm: Fix intialization warnings in kvm.c
x86, irq: Move irq_remapped out of x86 core code
x86, io_apic: Introduce eoi_ioapic_pin call-back
x86, msi: Introduce x86_msi.compose_msi_msg call-back
x86, irq: Introduce setup_remapped_irq()
x86, irq: Move irq_remapped() check into free_remapped_irq
x86, io-apic: Remove !irq_remapped() check from __target_IO_APIC_irq()
x86, io-apic: Move CONFIG_IRQ_REMAP code out of x86 core
x86, irq: Add data structure to keep AMD specific irq remapping information
x86, irq: Move irq_remapping_enabled declaration to iommu code
x86, io_apic: Remove irq_remapping_enabled check in setup_timer_IRQ0_pin
x86, io_apic: Move irq_remapping_enabled checks out of check_timer()
x86, io_apic: Convert setup_ioapic_entry to function pointer
x86, io_apic: Introduce set_affinity function pointer
x86, msi: Use IRQ remapping specific setup_msi_irqs routine
x86, hpet: Introduce x86_msi_ops.setup_hpet_msi
x86, io_apic: Introduce x86_io_apic_ops.print_entries for debugging
x86, io_apic: Introduce x86_io_apic_ops.disable()
x86, apic: Mask IO-APIC and PIC unconditionally on LAPIC resume
...
We already have the quirk entry for the mobile platform, but also
reports on some desktop versions. So be paranoid and set it
everywhere.
References: http://www.mail-archive.com/dri-devel@lists.freedesktop.org/msg33138.html
Cc: stable@vger.kernel.org
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "Sankaran, Rajesh" <rajesh.sankaran@intel.com>
Reported-and-tested-by: Mihai Moldovan <ionic@ionic.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tegra only supports, and always enables, device tree. Remove all ifdefs
for DT support from the driver.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Tegra only supports, and always enables, device tree. Remove all ifdefs
for DT support from the driver.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
dma_ops_domain_free on a NULL pointer is a no-op, so the NULL check in
amd_iommu_init_dma_ops() can be removed.
Signed-off-by: Cyril Roelandt <tipecaml@gmail.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
When dma_ops are initialized the unity mappings are
created. The init_device_table_dma() function makes sure DMA
from all devices is blocked by default. This opens a short
window in time where DMA to unity mapped regions is blocked
by the IOMMU. Make sure this does not happen by initializing
the device table after dma_ops.
Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <joro@8bytes.org>
kmemcheck complained about the use of uninitialized memory.
Fix by using kzalloc instead of kmalloc.
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
This fixes kernel crash because of BUG() in register address
validation.
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
'exynos_sysmmu_disable' is used only in this file and can be made static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
This is the Renesas IPMMU driver and IOMMU API implementation.
The IPMMU module supports the MMU function and the PMB function. The
MMU function provides address translation by pagetable compatible with
ARMv6. The PMB function provides address translation including
tile-linear translation. This patch implements the MMU function.
The iommu driver does not register a platform driver directly because:
- the register space of the MMU function and the PMB function
have a common register (used for settings flush), so they should ideally
have a way to appropriately share this register.
- the MMU function uses the IOMMU API while the PMB function does not.
- the two functions may be used independently.
Signed-off-by: Hideki EIRAKU <hdk@igel.co.jp>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Add the iommu_domain_window_enable() and iommu_domain_window_disable()
functions to the IOMMU-API. These functions will be used to setup
domains that are based on subwindows and not on paging.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
This attribute of a domain can be queried to find out if the
domain supports setting up page-tables using the iommu_map()
and iommu_unmap() functions.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
In case the page-size bitmap is zero the code path in
iommu_map and iommu_unmap is undefined. Make it defined and
return -ENODEV in this case.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Theoretically TEGRA_IOMMU_SMMU depends on ARCH_TEGRA_3x_SOC and
ARCH_TEGRA_114_SOC only. This patch allows a Tegra20 only kernel to
enable SMMU(Tegra20 doesn't have a SMMU), which could avoid editing
this Kconfig entry every time we add a new chip later.
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Do not repeat the checking loop in the read and write
functions. Use a single helper function for that check and
call it in both accessors.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Presently SMMU registers are located in discontiguous 3 blocks. They
are interleaved by MC registers. Ideally SMMU register blocks should
be in an independent one block, but it is too late to change this H/W
design. In the future Tegra chips over some generations, it is
expected that some of register block "size" can be extended towards
the end and also more new register blocks will be added at most a few
blocks. The starting address of each existing block won't change. This
patch allocates multiple number of register blocks dynamically based
on the info passed from DT. Those ranges are verified in the
accessors{read,write}. This may sacrifice some performance because a
new accessors prevents compiler optimization of a fixed size register
offset calculation. Since SMMU register accesses are not so frequent,
this would be acceptable. This patch is necessary to unify
"tegra-smmu.ko" over some Tegra SoC generations.
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Current kernels print this on my Dell server:
------------[ cut here ]------------
WARNING: at drivers/iommu/intel_irq_remapping.c:542
intel_enable_irq_remapping+0x7b/0x27e()
Hardware name: PowerEdge R620
Your BIOS is broken and requested that x2apic be disabled
This will leave your machine vulnerable to irq-injection attacks
Use 'intremap=no_x2apic_optout' to override BIOS request
[...]
Enabled IRQ remapping in xapic mode
x2apic not enabled, IRQ remapping is in xapic mode
This is inconsistent with itself -- interrupt remapping is *on*.
Fix the mess by making the warnings say what they mean and my
making sure that compatibility format interrupts (the dangerous
ones) are disabled if x2apic is present regardless of BIOS
settings.
With this patch applied, the output is:
Your BIOS is broken and requested that x2apic be disabled.
This will slightly decrease performance.
Use 'intremap=no_x2apic_optout' to override BIOS request.
Enabled IRQ remapping in xapic mode
x2apic not enabled, IRQ remapping is in xapic mode
This should make us as or more secure than we are now and
replace a rather scary warning with a much less scary warning on
silly but functional systems.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Link: http://lkml.kernel.org/r/2011b943a886fd7c46079eb10bc24fc130587503.1359759303.git.luto@amacapital.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull drm fixes from Dave Airlie:
"Intel, radeon and exynos fixes. Nothing too major or wierd: one dmar
fix and a radeon cursor corruption, along with misc exynos fixes."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (21 commits)
drm/exynos: add check for the device power status
drm/exynos: Make 'drm_hdmi_get_edid' static
drm/exynos: fimd and ipp are broken on multiplatform
drm/exynos: don't include plat/gpio-cfg.h
drm/exynos: Remove "internal" interrupt handling
drm/exynos: Add missing static specifiers in exynos_drm_rotator.c
drm/exynos: Replace mdelay with usleep_range
drm/exynos: Make ipp_handle_cmd_work static
drm/exynos: Make g2d_userptr_get_dma_addr static
drm/exynos: consider DMA_NONE flag to dmabuf import
drm/exynos: free sg object if dma_map_sg is failed
drm/exynos: added validation of edid for vidi connection
drm/exynos: let drm handle edid allocations
drm/radeon: Enable DMA_IB_SWAP_ENABLE on big endian hosts.
drm/radeon: fix a rare case of double kfree
radeon_display: Use pointer return error codes
drm/radeon: fix cursor corruption on DCE6 and newer
drm/i915: dump UTS_RELEASE into the error_state
iommu/intel: disable DMAR for g4x integrated gfx
drm/i915: GFX_MODE Flush TLB Invalidate Mode must be '1' for scanline waits
...
The IOMMU may stop processing page translations due to a perceived lack
of credits for writing upstream peripheral page service request (PPR)
or event logs. If the L2B miscellaneous clock gating feature is enabled
the IOMMU does not properly register credits after the log request has
completed, leading to a potential system hang.
BIOSes are supposed to disable L2B micellaneous clock gating by setting
L2_L2B_CK_GATE_CONTROL[CKGateL2BMiscDisable](D0F2xF4_x90[2]) = 1b. This
patch corrects that for those which do not enable this workaround.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <joro@8bytes.org>
The pointer obj is dereferenced in line 146 and 149 respectively, so it is not
necessary to check null again in line 149 and 175. And I have checked that all
the callers of these two functions guarantee the parameter obj passed is not
null.
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
The irq_remapped function is only used in IOMMU code after
the last patch. So move its definition there too.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This callback replaces the old __eoi_ioapic_pin function
which needs a special path for interrupt remapping.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This call-back points to the right function for initializing
the msi_msg structure. The old code for msi_msg generation
was split up into the irq-remapped and the default case.
The irq-remapped case just calls into the specific Intel or
AMD implementation when the device is behind an IOMMU.
Otherwise the default function is called.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This function does irq-remapping specific interrupt setup
like modifying the chip defaults.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The function is called unconditionally now in IO-APIC code
removing another irq_remapped() check from x86 core code.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Move all the code to either to the header file
asm/irq_remapping.h or to drivers/iommu/.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Remove the last left-over from this flag from x86 code.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Move these checks to IRQ remapping code by introducing the
panic_on_irq_remap() function.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This pointer is changed to a different function when IRQ
remapping is enabled.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
With interrupt remapping a special function is used to
change the affinity of an IO-APIC interrupt. Abstract this
with a function pointer.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Use seperate routines to setup MSI IRQs for both
irq_remapping_enabled cases.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This function pointer can be overwritten by the IRQ
remapping code. The irq_remapping_enabled check can be
removed from default_setup_hpet_msi.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This call-back is used to dump IO-APIC entries for debugging
purposes into the kernel log. VT-d needs a special routine
for this and will overwrite the default.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This function pointer is used to call a system-specific
function for disabling the IO-APIC. Currently this is used
for IRQ remapping which has its own disable routine.
Also introduce the necessary infrastructure in the interrupt
remapping code to overwrite this and other function pointers
as necessary by interrupt remapping.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Move the three easy to move checks in the x86' apic.c file
into the IRQ-remapping code.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMAR support on g4x/gm45 integrated gpus seems to be totally busted.
So don't bother, but instead disable it by default to allow distros to
unconditionally enable DMAR support.
v2: Actually wire up the right quirk entry, spotted by Adam Jackson.
Note that according to intel marketing materials only g45 and gm45
support DMAR/VT-d. So we have reports for all relevant gen4 pci ids by
now. Still, keep all the other gen4 ids in the quirk table in case the
marketing stuff confused me again, which would not be the first time.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=51921
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=538163
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=538163
Cc: Adam Jackson <ajax@redhat.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: stable@vger.kernel.org
Acked-By: David Woodhouse <David.Woodhouse@intel.com>
Tested-by: stathis <stathis@npcglib.org>
Tested-by: Mihai Moldovan <ionic@ionic.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Joerg Roedel <joerg.roedel@amd.com>
CC: Hiroshi DOYU <hdoyu@nvidia.com>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The iommu_init() initializes IOMMU internal structures and data
required for the IOMMU API as iommu_group_alloc().
It is registered as a subsys_initcall now.
One of the IOMMU users is going to be a PCI subsystem on POWER.
It discovers new IOMMU tables during the PCI scan so the logical
place to call iommu_group_alloc() is the moment when a new group
is discovered. However PCI scan is done from subsys_initcall hook
as IOMMU does so PCI hook can be (and is) called before the IOMMU one.
The patch moves IOMMU subsystem initialization one step earlier
to make sure that IOMMU is initialized before PCI scan begins.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Hiroshi Doyu <hdoyu@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Bharat Nihalani <bnihalani@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A few new features this merge-window. The most important one is
probably, that dma-debug now warns if a dma-handle is not checked with
dma_mapping_error by the device driver. This requires minor changes to
some architectures which make use of dma-debug. Most of these changes
have the respective Acks by the Arch-Maintainers.
Besides that there are updates to the AMD IOMMU driver for refactor the
IOMMU-Groups support and to make sure it does not trigger a hardware
erratum.
The OMAP changes (for which I pulled in a branch from Tony Lindgren's
tree) have a conflict in linux-next with the arm-soc tree. The conflict
is in the file arch/arm/mach-omap2/clock44xx_data.c which is deleted in
the arm-soc tree. It is safe to delete the file too so solve the
conflict. Similar changes are done in the arm-soc tree in the common
clock framework migration. A missing hunk from the patch in the IOMMU
tree will be submitted as a seperate patch when the merge-window is
closed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pPHZ
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"A few new features this merge-window. The most important one is
probably, that dma-debug now warns if a dma-handle is not checked with
dma_mapping_error by the device driver. This requires minor changes
to some architectures which make use of dma-debug. Most of these
changes have the respective Acks by the Arch-Maintainers.
Besides that there are updates to the AMD IOMMU driver for refactor
the IOMMU-Groups support and to make sure it does not trigger a
hardware erratum.
The OMAP changes (for which I pulled in a branch from Tony Lindgren's
tree) have a conflict in linux-next with the arm-soc tree. The
conflict is in the file arch/arm/mach-omap2/clock44xx_data.c which is
deleted in the arm-soc tree. It is safe to delete the file too so
solve the conflict. Similar changes are done in the arm-soc tree in
the common clock framework migration. A missing hunk from the patch
in the IOMMU tree will be submitted as a seperate patch when the
merge-window is closed."
* tag 'iommu-updates-v3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (29 commits)
ARM: dma-mapping: support debug_dma_mapping_error
ARM: OMAP4: hwmod data: ipu and dsp to use parent clocks instead of leaf clocks
iommu/omap: Adapt to runtime pm
iommu/omap: Migrate to hwmod framework
iommu/omap: Keep mmu enabled when requested
iommu/omap: Remove redundant clock handling on ISR
iommu/amd: Remove obsolete comment
iommu/amd: Don't use 512GB pages
iommu/tegra: smmu: Move bus_set_iommu after probe for multi arch
iommu/tegra: gart: Move bus_set_iommu after probe for multi arch
iommu/tegra: smmu: Remove unnecessary PTC/TLB flush all
tile: dma_debug: add debug_dma_mapping_error support
sh: dma_debug: add debug_dma_mapping_error support
powerpc: dma_debug: add debug_dma_mapping_error support
mips: dma_debug: add debug_dma_mapping_error support
microblaze: dma-mapping: support debug_dma_mapping_error
ia64: dma_debug: add debug_dma_mapping_error support
c6x: dma_debug: add debug_dma_mapping_error support
ARM64: dma_debug: add debug_dma_mapping_error support
intel-iommu: Prevent devices with RMRRs from being placed into SI Domain
...
The dma_pte_free_pagetable() function will only free a page table page
if it is asked to free the *entire* 2MiB range that it covers. So if a
page table page was used for one or more small mappings, it's likely to
end up still present in the page tables... but with no valid PTEs.
This was fine when we'd only be repopulating it with 4KiB PTEs anyway
but the same virtual address range can end up being reused for a
*large-page* mapping. And in that case were were trying to insert the
large page into the second-level page table, and getting a complaint
from the sanity check in __domain_mapping() because there was already a
corresponding entry. This was *relatively* harmless; it led to a memory
leak of the old page table page, but no other ill-effects.
Fix it by calling dma_pte_clear_range (hopefully redundant) and
dma_pte_free_pagetable() before setting up the new large page.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Tested-by: Ravi Murty <Ravi.Murty@intel.com>
Tested-by: Sudeep Dutt <sudeep.dutt@intel.com>
Cc: stable@kernel.org [3.0+]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use runtime PM functionality interfaced with hwmod enable/idle
functions, to replace direct clock operations and sysconfig
handling.
Due to reset sequence, pm_runtime_[get|put]_sync must be used, to
avoid possible operations with the module under reset. Because of
this and given that the driver uses spin_locks to protect their
critical sections, we must use pm_runtime_irq_safe in order for the
runtime ops to be happy, otherwise might_sleep_if checks in runtime
framework will complain.
The remaining pm_runtime out of iommu_enable and iommu_disable
corresponds to paths that can be accessed through debugfs, some of
them doesn't work if the module is not enabled first, but in future
if the mmu is idled withouth freeing, these are needed to debug.
Signed-off-by: Omar Ramirez Luna <omar.luna@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Use hwmod data and device attributes to build and register an
omap device for iommu driver.
- Update the naming convention in isp module.
- Remove unneeded check for number of resources, as this is now
handled by omap_device and prevents driver from loading.
- Now unused, remove platform device and resource data, handling
of sysconfig register for softreset purposes, use default
latency structure.
- Use hwmod API for reset handling.
Signed-off-by: Omar Ramirez Luna <omar.luna@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
The purpose of the mmu is to handle the memory accesses requested by
its users. Typically, the mmu is bundled with the processing unit in
a single IP block, which makes them to share the same clock to be
functional.
Currently, iommu code assumes that its user will be indirectly
clocking it, but being a separate mmu driver, it should handle
its own clocks, so as long as the mmu is requested it will be
powered ON and once detached it will be powered OFF.
The remaining clock handling out of iommu_enable and iommu_disable
corresponds to paths that can be accessed through debugfs, some of
them doesn't work if the module is not enabled first, but in future
if the mmu is idled withouth freeing, these are needed to debug.
Signed-off-by: Omar Ramirez Luna <omar.luna@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
For the interrupt to be generated, the mmu clock should be already
enabled while translating a virtual address, so, this call to clock
handling is just increasing/decreasing the counter.
This works now, because its users need the same clock and they
indirectly power the mmu, in this interrupt context the handling of
clocks inside the ISR doesn't seem to be needed nor helping.
Next patch should also correct the dependency on clients to handle
iommu clocks.
Signed-off-by: Omar Ramirez Luna <omar.luna@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
The AMD IOMMU driver only uses the page-sizes it gets from
IOMMU core and uses the appropriate page-size. So this
comment is not necessary.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
There is a bug in the hardware that will be triggered when
this page size is used. Make sure this does not happen.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
This is needed for the multiplatform kernels as the plat
and mach headers cannot be included.
These changes were agreed to be merged via the arm-soc
tree by Joerg and Ohad as these will cause some merge
conflicts with the other related clean-up branches.
So omap-for-v3.8/cleanup-headers-iommu should be added
as one of the depends branches for arm-soc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=yFcc
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/cleanup-headers-iommu-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren:
Move most of remaining omap iommu code to drivers/iommu.
This is needed for the multiplatform kernels as the plat
and mach headers cannot be included.
These changes were agreed to be merged via the arm-soc
tree by Joerg and Ohad as these will cause some merge
conflicts with the other related clean-up branches.
So omap-for-v3.8/cleanup-headers-iommu should be added
as one of the depends branches for arm-soc.
* tag 'omap-for-v3.8/cleanup-headers-iommu-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Move iommu/iovmm headers to platform_data
ARM: OMAP2+: Make some definitions local
ARM: OMAP2+: Move iommu2 to drivers/iommu/omap-iommu2.c
ARM: OMAP2+: Move plat/iovmm.h to include/linux/omap-iommu.h
ARM: OMAP2+: Move iopgtable header to drivers/iommu/
ARM: OMAP: Merge iommu2.h into iommu.h
Conflicts due to surrounding changes fixed up in:
arch/arm/mach-omap2/omap_hwmod_44xx_data.c
drivers/media/platform/omap3isp/ispvideo.c
Signed-off-by: Olof Johansson <olof@lixom.net>
For a single image to support multiple SoCs(GART/SMMU).
Reported-by: Arto Merilainen <amerilainen@nvidia.com>
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
For a single image to support multiple SoCs(GART/SMMU).
Reported-by: Arto Merilainen <amerilainen@nvidia.com>
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
smmu_flush_regs() does TLB/PTC flush all when freeing a second level
page table. This isn't necessay at all since each pte entry has been
already maintained by address in the above flush_ptc_and_tlb().
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQss0FAAoJEHm+PkMAQRiG6cEH/An3PYsWBBy27tzoLyVfJKF1
3m3vR8HS2tnHg6erxms+738jos59vrWXV0Ygnvw0DHbGR0HNb4rkwce/KXu/jgOD
MRYNYhlhMFJTEUFrSrcwKITrAV3kVPWXxPXgAR6Gzpr6NPKKM9TBzEv0ze56TFYz
asOxqeBcPSS7aFZlkoNsy1wG4l0Quo5ke8VZIxo9Me5qlqubAoZ6pING4wAGXqeE
tf81CevSdpe0nqr8/dlYyCvLjrurgpJQczxRCBI3mP6kLWGfUCVzZmcu86PfT9b+
35zNJwDneIoN+D9bVDHy6mrq9uQdmhWnQuhv1joTPn6RDn1nyBRBd+A5qLxSov4=
=CPoy
-----END PGP SIGNATURE-----
Merge tag 'v3.7-rc7' into next/cleanup
Merging in mainline back to next/cleanup since it has collected a few
conflicts between fixes going upstream and some of the cleanup patches.
Git doesn't auto-resolve some of them, and they're mostly noise so let's
take care of it locally.
Conflicts are in:
arch/arm/mach-omap2/omap_hwmod_44xx_data.c
arch/arm/plat-omap/i2c.c
drivers/video/omap2/dss/dss.c
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch is to prevent non-USB devices that have RMRRs associated with them from
being placed into the SI Domain during init. This fixes the issue where the RMRR info
for devices being placed in and out of the SI Domain gets lost.
Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Tested-by: Shuah Khan <shuah.khan@hp.com>
Reviewed-by: Donald Dutile <ddutile@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Move iommu/iovmm headers from plat/ to platform_data/ as part of the
single zImage work.
Partially based on an earlier version by Ido Yariv <ido@wizery.com>.
Cc: Ido Yariv <ido@wizery.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move some of the definitions in omap-iommu.h that can be made local to
either drivers/iommu.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Signed-off-by: Ido Yariv <ido@wizery.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
[tony@atomide.com: updated for header changes in the series]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This file should not be in arch/arm. Move it to drivers/iommu
to allow making most of the header local to drivers/iommu.
This is needed as we are removing plat and mach includes
from drivers for ARM common zImage support.
Cc: Ido Yariv <ido@wizery.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Cc: linux-media@vger.kernel.org
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like the iommu framework does not have generic functions
exported for all the needs yet. The hardware specific functions
are defined in files like intel-iommu.h and amd-iommu.h. Follow
the same standard for omap-iommu.h.
This is needed because we are removing plat and mach includes
for ARM common zImage support. Further work should continue
in the iommu framework context as only pure platform data will
be communicated from arch/arm/*omap*/* code to the iommu
framework.
Cc: Ido Yariv <ido@wizery.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Cc: linux-media@vger.kernel.org
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The iopgtable header file is only used by the iommu & iovmm drivers, so
move it to drivers/iommu/, as part of the single zImage effort.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Signed-off-by: Ido Yariv <ido@wizery.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
[tony@atomide.com: updated to be earlier in the series]
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can't assume this device exists, fall back to the bridge itself.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Tested-by: Matthew Thode <prometheanfire@gentoo.org>
Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <joro@8bytes.org>
We wish to empty arch/arm/mach-tegra/include/mach/ as much as possible
to enable single zImage. Move tegra-ahb.h to a more central location
(suggested by Arnd, OK'd by Greg KH), and actually make tegra-ahb.c
include the header to ensure client and provider agree on the prototype.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Nothing from this file is used, and the file will hopefully be deleted
soon.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Joerg Roedel <joerg.roedel@amd.com>
An alias doesn't always point to a physical device. When this
happens we must first verify that the IOMMU group isn't rooted in
a device above the alias. In this case the alias is effectively
just another quirk for the devices aliased to it. Alternatively,
the virtual alias itself may be the root of the IOMMU group. To
support this, allow a group to be hosted on the alias dev_data
for use by anything that might have the same alias.
Signed-off-by: Alex williamson <alex.williamson@redhat.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Add a WARN_ON to make it clear why we don't add dma_pdev->dev to the
group we're allocating.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This needs to be broken apart, start with pulling all the IOMMU
group init code into a new function.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
On some systems the BIOS puts the wrong device-id for the
IO-APIC into the IVRS table. The result is that interrupt
remapping is not working for the IO-APIC irqs. This usually
means a kernel panic at boot because the timer is not
working.
Fix this kernel panic by disabling interrupt remapping if
this problem is discovered in the IVRS table.
Reported-by: Andrew Oakley <andrew@ado.is-a-geek.net>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This time the IOMMU updates contain a bunch of fixes and cleanups to
various IOMMU drivers and the DMA debug code. New features are the
code for IRQ remapping support with the AMD IOMMU (preperation for that
was already merged in the last release) and a debugfs interface to
export some statistics in the NVidia Tegra IOMMU driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIbBAABAgAGBQJQbvi2AAoJECvwRC2XARrjIOcP92esm3auz49N2+rq5TAto6hX
4MbpUFgkpKQRdFUSgYOsuzjh+I46ZpWEVajCxM+9oJz4I3PalDH0hvN7VkcZTjvR
bENRaLOZNR39rtIPrNVlne2RX7DXjKxJF5+K7jD6uMGJdItPfXk1Vo0VrLw30+XD
E3pWNFCS+qJkWl7d0UGUJ6CzS1BZuHZdAx+XdHTa9DIV88jANiUefIV35cAVuqrL
xVDDDMs7ITIYn6vTpEj7/zXCHNcFS7Ki4FQxAQ4DFvpPdrvLtPMeXnVSBMg0LPpe
Gb2r8tjywo83yjZMoDxca6w20SJPkQHoWwlansGlg5j0KwqPhvD1M/OXwzbq6avd
fqL69kZTXttLY+qtnlM5YfAqySXevGmGusgmqEXT7GvbAH6dSqMDdPU2W6lt4zBd
80LyAdcwP5X5hT91KiOfGGpFY4np97dUC7QFbwAdgDO7t6R+c2OfSte6azzWkYm4
2eYCsIKy+5U6XLSNabp7QNAxnic3mt6/AVMydZsVLyjeQZ8ybCwslQjPxSNwQrxc
bx8z8KFY37UuFUs77dYFIChM8BJP6erKL0W1BOt0Ve2PWgeOaEl3y5n3mwBe+GXa
JU9SPqy0juNZIYJWU1ZE/90ULo6ZpB3wM7QpMgX1pJ7KTd1gYDjSXhAEJi5Eje8r
GNHlYwjxsQZQcvR19g8=
=Q5kj
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"This time the IOMMU updates contain a bunch of fixes and cleanups to
various IOMMU drivers and the DMA debug code. New features are the
code for IRQ remapping support with the AMD IOMMU (preperation for
that was already merged in the last release) and a debugfs interface
to export some statistics in the NVidia Tegra IOMMU driver."
* tag 'iommu-updates-v3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (27 commits)
iommu/amd: Remove obsolete comment line
dma-debug: Remove local BUS_NOTIFY_UNBOUND_DRIVER define
iommu/amd: Fix possible use after free in get_irq_table()
iommu/amd: Report irq remapping through IOMMU-API
iommu/amd: Print message to system log when irq remapping is enabled
iommu/irq: Use amd_iommu_irq_ops if supported
iommu/amd: Make sure irq remapping still works on dma init failure
iommu/amd: Add initialization routines for AMD interrupt remapping
iommu/amd: Add call-back routine for HPET MSI
iommu/amd: Implement MSI routines for interrupt remapping
iommu/amd: Add IOAPIC remapping routines
iommu/amd: Add routines to manage irq remapping tables
iommu/amd: Add IRTE invalidation routine
iommu/amd: Make sure IOMMU is not considered to translate itself
iommu/amd: Split device table initialization into irq and dma part
iommu/amd: Check if IOAPIC information is correct
iommu/amd: Allocate data structures to keep track of irq remapping tables
iommu/amd: Add slab-cache for irq remapping tables
iommu/amd: Keep track of HPET and IOAPIC device ids
iommu/amd: Fix features reporting
...
We should return NULL on error instead of the freed pointer.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Host bridge hotplug
- Protect acpi_pci_drivers and acpi_pci_roots (Taku Izumi)
- Clear host bridge resource info to avoid issue when releasing (Yinghai Lu)
- Notify acpi_pci_drivers when hot-plugging host bridges (Jiang Liu)
- Use standard list ops for acpi_pci_drivers (Jiang Liu)
Device hotplug
- Use pci_get_domain_bus_and_slot() to close hotplug races (Jiang Liu)
- Remove fakephp driver (Bjorn Helgaas)
- Fix VGA ref count in hotplug remove path (Yinghai Lu)
- Allow acpiphp to handle PCIe ports without native hotplug (Jiang Liu)
- Implement resume regardless of pciehp_force param (Oliver Neukum)
- Make pci_fixup_irqs() work after init (Thierry Reding)
Miscellaneous
- Add pci_pcie_type(dev) and remove pci_dev.pcie_type (Yijing Wang)
- Factor out PCI Express Capability accessors (Jiang Liu)
- Add pcibios_window_alignment() so powerpc EEH can use generic resource assignment (Gavin Shan)
- Make pci_error_handlers const (Stephen Hemminger)
- Cleanup drivers/pci/remove.c (Bjorn Helgaas)
- Improve Vendor-Specific Extended Capability support (Bjorn Helgaas)
- Use standard list ops for bus->devices (Bjorn Helgaas)
- Avoid kmalloc in pci_get_subsys() and pci_get_class() (Feng Tang)
- Reassign invalid bus number ranges (Intel DP43BF workaround) (Yinghai Lu)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=haBu
-----END PGP SIGNATURE-----
Merge tag 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Host bridge hotplug
- Protect acpi_pci_drivers and acpi_pci_roots (Taku Izumi)
- Clear host bridge resource info to avoid issue when releasing
(Yinghai Lu)
- Notify acpi_pci_drivers when hot-plugging host bridges (Jiang Liu)
- Use standard list ops for acpi_pci_drivers (Jiang Liu)
Device hotplug
- Use pci_get_domain_bus_and_slot() to close hotplug races (Jiang
Liu)
- Remove fakephp driver (Bjorn Helgaas)
- Fix VGA ref count in hotplug remove path (Yinghai Lu)
- Allow acpiphp to handle PCIe ports without native hotplug (Jiang
Liu)
- Implement resume regardless of pciehp_force param (Oliver Neukum)
- Make pci_fixup_irqs() work after init (Thierry Reding)
Miscellaneous
- Add pci_pcie_type(dev) and remove pci_dev.pcie_type (Yijing Wang)
- Factor out PCI Express Capability accessors (Jiang Liu)
- Add pcibios_window_alignment() so powerpc EEH can use generic
resource assignment (Gavin Shan)
- Make pci_error_handlers const (Stephen Hemminger)
- Cleanup drivers/pci/remove.c (Bjorn Helgaas)
- Improve Vendor-Specific Extended Capability support (Bjorn
Helgaas)
- Use standard list ops for bus->devices (Bjorn Helgaas)
- Avoid kmalloc in pci_get_subsys() and pci_get_class() (Feng Tang)
- Reassign invalid bus number ranges (Intel DP43BF workaround)
(Yinghai Lu)"
* tag 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (102 commits)
PCI: acpiphp: Handle PCIe ports without native hotplug capability
PCI/ACPI: Use acpi_driver_data() rather than searching acpi_pci_roots
PCI/ACPI: Protect acpi_pci_roots list with mutex
PCI/ACPI: Use acpi_pci_root info rather than looking it up again
PCI/ACPI: Pass acpi_pci_root to acpi_pci_drivers' add/remove interface
PCI/ACPI: Protect acpi_pci_drivers list with mutex
PCI/ACPI: Notify acpi_pci_drivers when hot-plugging PCI root bridges
PCI/ACPI: Use normal list for struct acpi_pci_driver
PCI/ACPI: Use DEVICE_ACPI_HANDLE rather than searching acpi_pci_roots
PCI: Fix default vga ref_count
ia64/PCI: Clear host bridge aperture struct resource
x86/PCI: Clear host bridge aperture struct resource
PCI: Stop all children first, before removing all children
Revert "PCI: Use hotplug-safe pci_get_domain_bus_and_slot()"
PCI: Provide a default pcibios_update_irq()
PCI: Discard __init annotations for pci_fixup_irqs() and related functions
PCI: Use correct type when freeing bus resource list
PCI: Check P2P bridge for invalid secondary/subordinate range
PCI: Convert "new_id"/"remove_id" into generic pci_bus driver attributes
xen-pcifront: Use hotplug-safe pci_get_domain_bus_and_slot()
...
Report the availability of irq remapping through the
IOMMU-API to allow KVM device passthrough again without
additional module parameter overrides.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Do not deinitialize the AMD IOMMU driver completly when
interrupt remapping is already in use but the initialization
of the DMA layer fails for some reason. Make sure the IOMMU
can still be used to remap interrupts.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Add the six routines required to setup interrupt remapping
with the AMD IOMMU. Also put it all together into the AMD
specific irq_remap_ops.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Add the routine to setup interrupt remapping for ioapic
interrupts. Also add a routine to change the affinity of an
irq and to free an irq allocation for interrupt remapping.
The last two functions will also be used for MSI interrupts.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Add routines to:
* Alloc remapping tables and single entries from these
tables
* Change entries in the tables
* Free entries in the table
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Add routine to invalidate the IOMMU cache for interupt
translations. Also include the IRTE caches when flushing all
IOMMU caches.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The IVRS table usually includes the IOMMU device. But the
IOMMU does never translate itself, so make sure the IOMMU
driver knows this.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
When the IOMMU is enabled very early (as with irq-remapping)
some devices are still in BIOS hand. When dma is blocked
early this can cause lots of IO_PAGE_FAULTs. So delay the
DMA initialization and do it right before the dma_ops are
initialized.
To be secure, block all interrupts by default when irq-remapping is
enabled in the system. They will be reenabled on demand
later. Without blocking interrupts by default devices can
issue arbitrary interrupts by sending special DMA packets to
the CPU that look like MSI messages. This is especially
dangerous when a device is assigned to a KVM guest because
the guest can then DoS the host.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Joerg Roedel