This has been on my TODO list for some time now: the control that enables the video
loopback was part of the controls of the video output device instead of the video
capture device. In practice this was quite annoying since you expect it at the capture
side since that's where you want to make the decision whether to use the TPG or looped
video.
This patch moves the control from the output to the capture side.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The tuner FMD1216ME_MK3 suffers the same problem as FMD1216MEX_MK3,
as described in saa7134-cards.c (disabled IF, enabled DVB-T). The
card does work under MS Windows, after soft reboot into Linux it
continues to work, only then tda9887 is loaded as well.
I copied the relevant code from the BEHOLD_H6 section to MD7134.
The CTX946 TV card doesn't detect a signal after cold boot, seems
Signed-off-by: Juergen Gier <juergen.gier@gmx.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Current v4l2_of_parse_parallel_bus function attempts to parse the
DT properties for the parallel bus as well as BT656 bus.
If the pclk-sample property is defined for the BT656 bus, it is still
marked as a parallel bus.
Fix this by parsing the pclk after the bus_type is selected.
Only when hsync or vsync properties are specified, the bus_type should
be set to V4L2_MBUS_PARALLEL.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Load PCTV 460e tda10071 demod and a8293 SEC using I2C client bindings.
Remove old unused tda10071 config struct. We are using I2C platform
data now.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit 84cb7be43c broke vivid-tpg
(uninitialized variable p).
This patch takes a different approach: four different functions are
created, one for each PRINTSTR version.
In order to avoid the 'the frame size of 1308 bytes is larger than 1024
bytes' warning I had to mark those functions with 'noinline'. For
whatever reason gcc seems to inline this aggressively and it is doing
weird things with the stack.
I tried to read the assembly code, but I couldn't see what exactly it
was doing on the stack.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Document the new Transfer Function control (and fix the documentation for
the other colorspace controls which were not quite correct).
Mention the support for 4:2:0 and more multiplanar formats.
Update the TODO list at the end.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Simplify cobalt_g/try_fmt_vid_cap by not setting the colorspace fields in
pix again (since v4l2_fill_pix_format does that already), and by using
v4l2_fill_mbus_format in cobalt_s_fmt_vid_out which allows the get_fmt
call to be dropped as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for the transfer function to the cobalt driver: make sure it is
passed on to/retrieved from the sub-device correctly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Precalculate all the colorspace/transfer function combinations in order
to easily generate the correct colors.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for the transfer function: create a new control for it,
and support it for both capture and output sides.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make this part of the format check.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Still preliminary, but the information is at least there.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Document the new field and defines to set the transfer function needed
to correctly decode the colors of an image.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In the past the transfer function was implied by the colorspace. However,
it is an independent entity in its own right. Add support for explicitly
choosing the transfer function.
This change will allow us to represent linear RGB (as is used by openGL), and
it will make it easier to work with decoded video material since most codecs
store the transfer function as a separate property as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of using a state machine and a switch with lots of
fall-trough, use gotos and cleanup the error handling loop.
That removes those two smatch warnings:
drivers/staging/media/lirc/lirc_imon.c:933 imon_probe() warn: possible memory leak of 'context'
drivers/staging/media/lirc/lirc_imon.c:933 imon_probe() warn: possible memory leak of 'driver'
And make the error handling code more standard.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There's a dead code on usbvision that makes it harder to read
and produces a smatch warning about bad identation.
Improve the code readability and add a FIXME to warn about
the current hack there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Smatch reports a warning:
drivers/media/usb/tm6000/tm6000-video.c:646 tm6000_prepare_isoc() error: we previously assumed 'dev->urb_buffer' could be null (see line 624)
This is not really a problem, but it actually shows that the check
if urb_buffer is NULL is being done twice: at the if and at
tm6000_alloc_urb_buffers().
We don't need to do it twice. So, remove the extra check. The code
become cleaner, and, as a collateral effect, smatch becomes happy.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Smatch currently produces two warnings:
drivers/media/pci/ivtv/ivtv-fileops.c:901 ivtv_v4l2_close() warn: suspicious bitop condition
drivers/media/pci/ivtv/ivtv-fileops.c:1026 ivtv_open() warn: suspicious bitop condition
Those are false positives, but it is not hard to get rid of them by
using a different way to evaluate the macro, splitting the logical
boolean evaluation from the bitmap one.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/pci/bt8xx/dst_ca.c:323 ca_get_message() warn: this array is probably non-NULL. 'p_ca_message->msg'
drivers/media/pci/bt8xx/dst_ca.c:498 ca_send_message() warn: this array is probably non-NULL. 'p_ca_message->msg'
Those two checks are needless/useless, as the ca_msg struct is
declared as:
typedef struct ca_msg {
unsigned int index;
unsigned int type;
unsigned int length;
unsigned char msg[256];
} ca_msg_t;
So, if the p_ca_message pointer is not null, msg will also be
not null.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/dvb-frontends/dib0090.c:1710 dib0090_dc_offset_calibration() warn: missing break? reassigning '*tune_state'
There's no need to change tune_state there, as the fall though code
will change it again to another state. So, simplify it by
removing the dead code.
While here, fix a typo:
Sart => Start
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Smatch reports two issues:
drivers/media/platform/sh_vou.c:670 vou_adjust_output() error: buffer overflow 'vou_scale_v_num' 3 <= 4
drivers/media/platform/sh_vou.c:670 vou_adjust_output() error: buffer overflow 'vou_scale_v_den' 3 <= 4
It seems that there's actually a bug here: the same var (idx) is used
as an index for vertical and horizontal scaling arrays. However,
there are 4 elements on the h arrays, and only 3 at the v ones.
On the first loop, it may select index 4 for the horizontal array.
In this case, if the second loop fails to select an index, the
code would keep using 4 for the vertical array, with is past of
the array sizes.
The intent here seems to use index 0, if the scale is not found.
So, use a separate var for the vertical index.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/dvb-frontends/drxk_hard.c:3277 dvbt_sc_command() warn: missing break? reassigning 'status'
This is basically because the error handling logic there was crappy.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove the following compilation warnings:
drivers/media/platform/vivid/vivid-tpg.c: In function 'tpg_gen_text':
drivers/media/platform/vivid/vivid-tpg.c:1562:1: warning: the frame size of 1308 bytes is larger than 1024 bytes [-Wframe-larger-than=]
}
^
This seems to be due to some bad optimization done by gcc.
Moving the for() loop to happen inside the macro solves the
issue.
While here, fix CodingStyle at the switch().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Commits a0f10c131c and
6c9fe76536 ("media: s5p-mfc: fix broken
pointer cast on 64bit arch") fixed issue with lossy cast on 64-bit
architectures. However it also removed __iomem attribute from that cast.
This leads to sparse warnings. This patch fixes those warnings by adding
__iomem cast in case of v6+ code version and replacing readl/writel by
simple u32 load/store operations in case of v5 code (which is called on
system memory allocated by dma_alloc_coherent() instead of io registers).
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch makes use of helper function v4l2_get_timestamp()
to set the timestamp of vb2 buffer.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
V4L2 drivers should use MONOTONIC timestamps instead of gettimeofday,
which is affected by daylight savings time.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch sets nbuffers to three or more and drops the
unset member video_limit which just a copy paste from
earlier driver.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
clear of the output_specs before passing it to the
configure_resizer_out_params(), so that no garbage values
are set.
This fixes following build warning:
drivers/staging/media/davinci_vpfe/dm365_resizer.c: In function 'resizer_set_stream':
drivers/staging/media/davinci_vpfe/dm365_resizer.c:190:46: warning: 'output_specs.vst_c'
may be used uninitialized in this function [-Wmaybe-uninitialized]
param->ext_mem_param[index].rsz_sdr_ptr_s_c = output->vst_c;
^
drivers/staging/media/davinci_vpfe/dm365_resizer.c:316:30: note: 'output_specs.vst_c' was declared here
struct vpfe_rsz_output_spec output_specs;
^
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We need own I2C locking because of tuner I2C adapter/repeater.
Firmware command is executed using I2C send + reply message. Default
I2C adapter locking protects only single I2C operation, not whole
send + reply sequence as needed. Due to that, it was possible tuner
I2C message interrupts firmware command sequence.
Reported-by: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The changeset dc9ef7d112 change the open() ioctl documentation to
match the V4L2 open(). However, some cut-and-pasted stuff doesn't
match what actually happens at the DVB core.
So, fix the documentation entry to be more accurate with the DVB
frontend open() specifics.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
To fix the last xmllint errors the open and close function reference
description was rewritten based on the v4l2 open and close functions.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fixes a large number of xmllint errors.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The UVC_DEV_DISCONNECTED flag is set when the USB device is
disconnected, and checked in the open() handler to refuse opening a
device that has been disconnected.
This is inherently racy, but the race condition is taken care of in the
V4L2 core, which also fails open() calls when the V4L2 device node has
been unregistered. As the uvcvideo USB disconnect handler unregisters
all its video device nodes, the UVC_DEV_DISCONNECTED flag doesn't serve
any purpose anymore and can be removed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The "TOSHIBA Web Camera - 5M" Chicony device (04f2:b50b) seems to
compute the bandwidth on 16 bits and erroneously sign-extend it to
32 bits, resulting in a huge bandwidth value. Detect and fix that
condition by setting the 16 MSBs to 0 when they're all equal to 1.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that videobuf2-vmalloc supports exporting buffers, add support for
the DMABUF exporter role by plugging in the videobuf2 ioctl helper.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is AF9035 + MxL5007T.
Driver reports:
prechip_version=00 chip_version=03 chip_type=3802
Not sure if that USB ID is reserved only for HP brand or if it is
common, but the stick I have is branded as HP part no. 580715-001
rmn A867.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hans Verkuil