In case of HSDK we have intermediate INTC in for of DW APB GPIO controller
which is used as a de-bounce logic for interrupt wires that come from
outside the board.
We cannot use existing "irq-dw-apb-ictl" driver here because all input
lines are routed to corresponding output lines but not muxed into one
line (this is configured in RTL and we cannot change this in software).
But even if we add such a feature to "irq-dw-apb-ictl" driver that won't
benefit us as higher-level INTC (in case of HSDK it is IDU) anyways has
per-input control so adding fully-controller intermediate INTC will only
bring some overhead on interrupt processing but no other benefits.
Thus we just do one-time configuration of DW APB GPIO controller and
forget about it.
Based on implementation available on arch/arc/plat-axs10x/axs10x.c file.
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Get rid of core pll frequency set in platform code as we set it via
device tree using 'assigned-clock-rates' property.
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
With current SDIO CIU clock frequency (12500000Hz) DW MMC
controller fails to initialize some SD cards (which don't
support slow mode).
So increase SDIO CIU frequency from 12500000Hz to 50000000Hz by
switching from the default divisor value (div-by-8) to the
minimum possible value of the divisor (div-by-2) in HSDK platform
code.
Reported-by: Vineet Gupta <vgupta@synopsys.com>
Tested-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Add temporary fix to HSDK platform code to setup CPU frequency
to 1GHz on early boot.
We can remove this fix when smart hsdk pll driver will be
introduced, see discussion:
https://www.mail-archive.com/linux-snps-arc@lists.infradead.org/msg02689.html
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This initial port adds support of ARC HS Development Kit board with some
basic features such serial port, USB, SD/MMC and Ethernet.
Essentially we run Linux kernel on all 4 cores (i.e. utilize SMP) and
heavily use IO Coherency for speeding-up DMA-aware peripherals.
Note as opposed to other ARC boards we link Linux kernel to
0x9000_0000 intentionally because cores 1 and 3 configured with DCCM
situated at our more usual link base 0x8000_0000. We still can use
memory region starting at 0x8000_0000 as we reallocate DCCM in our
platform code.
Note that PAE remapping for DMA clients does not work due to an RTL bug,
so CREG_PAE register must be programmed to all zeroes, otherwise it will
cause problems with DMA to/from peripherals even if PAE40 is not used.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Gustavo Pimentel