Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Signed-off-by: Thierry Reding <treding@nvidia.com>
With the split of MIPI calibration into tegra_mipi_calibrate() and
tegra_mipi_wait(), MIPI clock is not kept enabled and mutex is not locked
till the calibration is done.
So, this patch keeps MIPI clock enabled and mutex locked after triggering
start of calibration till its done.
To let calibration process go through its finite sequence codes before
calibration logic waiting for pads idle state added wait time of 75usec
to make sure it sees idle state to apply the results.
This patch renames tegra_mipi_calibrate() as tegra_mipi_start_calibration()
and tegra_mipi_wait() as tegra_mipi_finish_calibration() to be inline
with their usage.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
SW can trigger MIPI pads calibration any time after power on
but calibration results will be latched and applied to the pads
by MIPI CAL unit only when the link is in LP-11 state and then
status register will be updated.
For CSI, trigger of pads calibration happen during CSI stream
enable where CSI receiver is kept ready prior to sensor or CSI
transmitter stream start.
So, pads may not be in LP-11 at this time and waiting for the
calibration to be done immediate after calibration start will
result in timeout.
This patch splits tegra_mipi_calibrate() and tegra_mipi_wait()
so triggering for calibration and waiting for it to complete can
happen at different stages.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use readl_relaxed_poll_timeout() in tegra_mipi_wait() to simplify
the code.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra CSI driver need a separate MIPI device for each channel as
calibration of corresponding MIPI pads for each channel should
happen independently.
So, this patch updates tegra_mipi_request() API to add a device_node
pointer argument to allow creating mipi device for specific device
node rather than a device.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The MIPI DSI output on Tegra SoCs requires some external logic to
calibrate the MIPI pads before a video signal can be transmitted. This
MIPI calibration logic requires to be powered on while the MIPI pads are
being used, which is currently done as part of the DSI driver's probe
implementation.
This is suboptimal because it will leave the MIPI calibration logic
powered up even if the DSI output is never used.
On Tegra114 and earlier this behaviour also causes the driver to hang
while trying to power up the MIPI calibration logic because the power
partition that contains the MIPI calibration logic will be powered on
by the display controller at output pipeline configuration time. Thus
the power up sequence for the MIPI calibration logic happens before
it's power partition is guaranteed to be enabled.
Fix this by splitting up the API into a request/free pair of functions
that manage the runtime dependency between the DSI and the calibration
modules (no registers are accessed) and a set of enable, calibrate and
disable functions that program the MIPI calibration logic at points in
time where the power partition is really enabled.
While at it, make sure that the runtime power management also works in
ganged mode, which is currently also broken.
Reported-by: Jonathan Hunter <jonathanh@nvidia.com>
Tested-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Keep track of the number of users of DSI and CSI pads and power down the
regulators that supply the bricks when all users are gone.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some changes are needed to the configuration settings for some lanes. In
addition, the clock lanes for the CSI pads can no longer be calibrated.
Signed-off-by: Thierry Reding <treding@nvidia.com>
While Tegra132 has the same pads as Tegra124, some configuration values
need to be programmed slightly differently.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Before starting a new calibration cycle, make sure to clear the current
status by writing a 1 to the various "calibration done" bits.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use more consistent names for the clock lane configuration registers and
fix the offset of the upper clock lane configuration register for the
first DSI pad.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Parameterize more of the register programming to accomodate for changes
required by future SoC generations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
During calibration, sets the "internal reference level for drive pull-
down" to the value specified in the Tegra TRM.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Include the clock lanes when calibrating the MIPI PHY on Tegra124
compatible devices.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
[treding@nvidia.com: bikeshedding]
Signed-off-by: Thierry Reding <treding@nvidia.com>
By paving the CTRL reg value, the current code changes MIPI_CAL_PRESCALE
("Auto-cal calibration step prescale") from 1us to 0.1us (val=0). In the
description for PHY's noise filter (MIPI_CAL_NOISE_FLT), the TRM states
that if the value of the prescale is 0 (or 0.1us), the filter should be
set between 2-5. However, the current code sets it to 0.
For now, let's keep the prescale and filter values as-is, which is most
likely the power-on-reset values of 0x2 and 0xa, respectively.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On 64-bit platforms an unsigned long would be 64 bit and cause
unnecessary casting when being passed to writel() or returned from
readl(). Make register values 32 bits wide to avoid that.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Include the linux/host1x.h and dev.h headers so that function prototypes
are visible to keep sparse from suggesting that their implementations be
made static.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Ye Xingchen