If skb can be sent right away, we certainly should do that
if it's in the middle of the queue because it won't get
more data into it.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible that lost_cnt_hint gets underflow in
tcp_clean_rtx_queue because the cumulative ACK can cover
the segment where lost_skb_hint points to only partially,
which means that the hint is not cleared, opposite to what
my (earlier) comment claimed.
Also I don't agree what I ended up writing about non-trivial
case there to be what I intented to say. It was not supposed
to happen that the hint won't get cleared and we underflow
in any scenario.
In general, this is quite hard to trigger in practice.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Backtracking to sacked skbs is a horrible performance killer
since the hint cannot be advanced successfully past them...
...And it's totally unnecessary too.
In theory this is 2.6.27..28 regression but I doubt anybody
can make .28 to have worse performance because of other TCP
improvements.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's conflicting assumptions in shifting, the caller assumes
that dupsack results in S'ed skbs (or a part of it) for sure but
never gave a hint to tcp_sacktag_one when dsack is actually in
use. Thus DSACK retrans_out -= pcount was not taken and the
counter became out of sync. Remove obstacle from that information
flow to get DSACKs accounted in tcp_sacktag_one as expected.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Tested-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Attribute function with __releases(...)
Fix this sparse warning:
net/ipv4/inet_fragment.c:276:35: warning: context imbalance in 'inet_frag_find' - unexpected unlock
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions time_before is more robust for comparing
jiffies against other values.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions time_before is more robust for comparing
jiffies against other values.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the return value of nlmsg_notify() as follows:
If NETLINK_BROADCAST_ERROR is set by any of the listeners and
an error in the delivery happened, return the broadcast error;
else if there are no listeners apart from the socket that
requested a change with the echo flag, return the result of the
unicast notification. Thus, with this patch, the unicast
notification is handled in the same way of a broadcast listener
that has set the NETLINK_BROADCAST_ERROR socket flag.
This patch is useful in case that the caller of nlmsg_notify()
wants to know the result of the delivery of a netlink notification
(including the broadcast delivery) and take any action in case
that the delivery failed. For example, ctnetlink can drop packets
if the event delivery failed to provide reliable logging and
state-synchronization at the cost of dropping packets.
This patch also modifies the rtnetlink code to ignore the return
value of rtnl_notify() in all callers. The function rtnl_notify()
(before this patch) returned the error of the unicast notification
which makes rtnl_set_sk_err() reports errors to all listeners. This
is not of any help since the origin of the change (the socket that
requested the echoing) notices the ENOBUFS error if the notification
fails and should resync itself.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IP_ADVANCED_ROUTER Kconfig describes the rp_filter
proc option. Recent changes added a loose mode.
Instead of documenting this change too places, refer to
the document describing it:
Documentation/networking/ip-sysctl.txt
I'm considering moving the rp_filter description away
from the Kconfig file into ip-sysctl.txt.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
netns: fix double free at netns creation
veth : add the set_mac_address capability
sunlance: Beyond ARRAY_SIZE of ib->btx_ring
sungem: another error printed one too early
ISDN: fix sc/shmem printk format warning
SMSC: timeout reaches -1
smsc9420: handle magic field of ethtool_eeprom
sundance: missing parentheses?
smsc9420: fix another postfixed timeout
wimax/i2400m: driver loads firmware v1.4 instead of v1.3
vlan: Update skb->mac_header in __vlan_put_tag().
cxgb3: Add support for PCI ID 0x35.
tcp: remove obsoleted comment about different passes
TG3: &&/|| confusion
ATM: misplaced parentheses?
net/mv643xx: don't disable the mib timer too early and lock properly
net/mv643xx: use GFP_ATOMIC while atomic
atl1c: Atheros L1C Gigabit Ethernet driver
net: Kill skb_truesize_check(), it only catches false-positives.
net: forcedeth: Fix wake-on-lan regression
To remove the possibility of packets flying around when network
devices are being cleaned up use reisger_pernet_subsys instead of
register_pernet_device.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Acked-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently I had a kernel panic in icmp_send during a network namespace
cleanup. There were packets in the arp queue that failed to be sent
and we attempted to generate an ICMP host unreachable message, but
failed because icmp_sk_exit had already been called.
The network devices are removed from a network namespace and their
arp queues are flushed before we do attempt to shutdown subsystems
so this error should have been impossible.
It turns out icmp_init is using register_pernet_device instead
of register_pernet_subsys. Which resulted in icmp being shut down
while we still had the possibility of packets in flight, making
a nasty NULL pointer deference in interrupt context possible.
Changing this to register_pernet_subsys fixes the problem in
my testing.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Acked-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While going through net/ipv4/Kconfig cleanup whitespaces.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reverse path filter (rp_filter) will NOT get enabled
when enabling forwarding. Read the code and tested in
in practice.
Most distributions do enable it in startup scripts.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of compile warning about non-const format
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend existing reverse path filter option to allow strict or loose
filtering. (See http://en.wikipedia.org/wiki/Reverse_path_filtering).
For compatibility with existing usage, the value 1 is chosen for strict mode
and 2 for loose mode.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CIPSO protocol engine incorrectly stated that the FIPS-188 specification
could be found in the kernel's Documentation directory. This patch corrects
that by removing the comment and directing users to the FIPS-188 documented
hosted online. For the sake of completeness I've also included a link to the
CIPSO draft specification on the NetLabel website.
Thanks to Randy Dunlap for spotting the error and letting me know.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
Our TCP stack does not set the urgent flag if the urgent pointer
does not fit in 16 bits, i.e., if it is more than 64K from the
sequence number of a packet.
This behaviour is different from the BSDs, and clearly contradicts
the purpose of urgent mode, which is to send the notification
(though not necessarily the associated data) as soon as possible.
Our current behaviour may in fact delay the urgent notification
indefinitely if the receiver window does not open up.
Simply matching BSD however may break legacy applications which
incorrectly rely on the out-of-band delivery of urgent data, and
conversely the in-band delivery of non-urgent data.
Alexey Kuznetsov suggested a safe solution of following BSD only
if the urgent pointer itself has not yet been transmitted. This
way we guarantee that when the remote end sees the packet with
non-urgent data marked as urgent due to wrap-around we would have
advanced the urgent pointer beyond, either to the actual urgent
data or to an as-yet untransmitted packet.
The only potential downside is that applications on the remote
end may see multiple SIGURG notifications. However, this would
occur anyway with other TCP stacks. More importantly, the outcome
of such a duplicate notification is likely to be harmless since
the signal itself does not carry any information other than the
fact that we're in urgent mode.
Thanks to Ilpo Järvinen for fixing a critical bug in this and
Jeff Chua for reporting that bug.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is obsolete since the passes got combined.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: syntax fix
Interestingly enough this compiles w/o any complaints:
orphans = percpu_counter_sum_positive(&tcp_orphan_count),
sockets = percpu_counter_sum_positive(&tcp_sockets_allocated),
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instructions for time stamping outgoing packets are take from the
socket layer and later copied into the new skb.
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gro: Optimise TCP packet reception
As this function can be called more than half a million times for
10GbE, it's important to optimise it as much as we can.
This patch uses bit ops to logical ops, as well as open coding
memcmp to exploit alignment properties.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As this function can be called more than half a million times for
10GbE, it's important to optimise it as much as we can.
This patch does some obvious changes to use 2-byte and 4-byte
operations instead of byte-oriented ones where possible. Bit
ops are also used to replace logical ops to reduce branching.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like the UDP header fix, pskb_may_pull() can potentially
alter the SKB buffer. Thus the saddr and daddr, pointers
may point to the old skb->data buffer.
I haven't seen corruptions, as its only seen if the old
skb->data buffer were reallocated by another user and
written into very quickly (or poison'd by SLAB debugging).
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP header pointer assignment must happen after calling
pskb_may_pull(). As pskb_may_pull() can potentially alter the SKB
buffer.
This was exposted by running multicast traffic through the NIU driver,
as it won't prepull the protocol headers into the linear area on
receive.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 93821778de (udp: Fix rcv socket
locking) accidentally removed sk_drops increments for UDP IPV4
sockets.
This field can be used to detect incorrect sizing of socket receive
buffers.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_alloc now sets sk_family so this is redundant. In fact it caught
my eye because sock_init_data already uses sk_family so this is too
late anyway.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
And switch bsockets to atomic_t since it might be changed in parallel.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Stephen Hemminger <shemminger@vyatta.com>
Fix regression introduced by a9d8f9110d
("inet: Allowing more than 64k connections and heavily optimize
bind(0) time.")
Based upon initial patches and feedback from Evegniy Polyakov and
Eric Dumazet.
From Eric Dumazet:
--------------------
Also there might be a problem at line 175
if (sk->sk_reuse && sk->sk_state != TCP_LISTEN && --attempts >= 0) {
spin_unlock(&head->lock);
goto again;
If we entered inet_csk_get_port() with a non null snum, we can "goto again"
while it was not expected.
--------------------
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds another inet device option to enable gratuitous ARP
when device is brought up or address change. This is handy for
clusters or virtualization.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Base versions handle constant folding now.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unfortunately simplicity isn't always the best. The fraginfo
interface turned out to be suboptimal. The problem was quite
obvious. For every packet, we have to copy the headers from
the frags structure into skb->head, even though for 99% of the
packets this part is immediately thrown away after the merge.
LRO didn't have this problem because it directly read the headers
from the frags structure.
This patch attempts to address this by creating an interface
that allows GRO to access the headers in the first frag without
having to copy it. Because all drivers that use frags place the
headers in the first frag this optimisation should be enough.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_splice_data_recv has two lengths to consider: the len parameter it
gets from tcp_read_sock, which specifies the amount of data in the skb,
and rd_desc->count, which is the amount of data the splice caller still
wants. Currently it passes just the latter to skb_splice_bits, which then
splices min(rd_desc->count, skb->len - offset) bytes.
Most of the time this is fine, except when the skb contains urgent data.
In that case len goes only up to the urgent byte and is less than
skb->len - offset. By ignoring len tcp_splice_data_recv may a) splice
data tcp_read_sock told it not to, b) return to tcp_read_sock a value > len.
Now, tcp_read_sock doesn't handle used > len and leaves the socket in a
bad state (both sk_receive_queue and copied_seq are bad at that point)
resulting in duplicated data and corruption.
Fix by passing min(rd_desc->count, len) to skb_splice_bits.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Acked-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 9088c56095
(udp: Improve port randomization) introduced a regression for UDP bind() syscall
to null port (getting a random port) in case lot of ports are already in use.
This is because we do about 28000 scans of very long chains (220 sockets per chain),
with many spin_lock_bh()/spin_unlock_bh() calls.
Fix this using a bitmap (64 bytes for current value of UDP_HTABLE_SIZE)
so that we scan chains at most once.
Instead of 250 ms per bind() call, we get after patch a time of 2.9 ms
Based on a report from Vitaly Mayatskikh
Reported-by: Vitaly Mayatskikh <v.mayatskih@gmail.com>
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Tested-by: Vitaly Mayatskikh <v.mayatskih@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of keeping candidate tunnel device from all categories,
keep only one candidate with best score. This optimizes stack
usage and speeds up exit code.
Signed-off-by: Timo Teras <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
This last patch makes the appropriate changes to use and propagate the
network namespace where needed in IPv4 multicast routing code.
This consists mainly in replacing all the remaining init_net occurences
with current netns pointer retrieved from sockets, net devices or
mfc_caches depending on the routines' contexts.
Some routines receive a new 'struct net' parameter to propagate the current
netns:
* vif_add/vif_delete
* ipmr_new_tunnel
* mroute_clean_tables
* ipmr_cache_find
* ipmr_cache_report
* ipmr_cache_unresolved
* ipmr_mfc_add/ipmr_mfc_delete
* ipmr_get_route
* rt_fill_info (in route.c)
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Declare IPv4 multicast forwarding /proc/net entries per-namespace:
/proc/net/ip_mr_vif
/proc/net/ip_mr_cache
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preliminary work to make IPv4 multicast routing netns-aware.
Declare variable 'reg_vif_num' per-namespace, move into struct netns_ipv4.
At the moment, this variable is only referenced in init_net.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preliminary work to make IPv4 multicast routing netns-aware.
Declare IPv multicast routing variables 'mroute_do_assert' and
'mroute_do_pim' per-namespace in struct netns_ipv4.
At the moment, these variables are only referenced in init_net.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preliminary work to make IPv4 multicast routing netns-aware.
Declare variable cache_resolve_queue_len per-namespace: move it into
struct netns_ipv4.
This variable counts the number of unresolved cache entries queued in the
list mfc_unres_queue. This list is kept global to all netns as the number
of entries per namespace is limited to 10 (hardcoded in routine
ipmr_cache_unresolved).
Entries belonging to different namespaces in mfc_unres_queue will be
identified by matching the mfc_net member introduced previously in
struct mfc_cache.
Keeping this list global to all netns, also allows us to keep a single
timer (ipmr_expire_timer) to handle their expiration.
In some places cache_resolve_queue_len value was tested for arming
or deleting the timer. These tests were equivalent to testing
mfc_unres_queue value instead and are replaced in this patch.
At the moment, cache_resolve_queue_len is only referenced in init_net.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen