Currently, select_tuning() is called after RPM resume. But
select_tuning() needs some additional function calls to work correctly.
Instead of reimplementing the whole postprocessing, just enforce
retuning.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200129203709.30493-5-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
check_scc_error() is too Renesas specific. Let's just call it
check_retune() to make it also easier understandable what it does.
Only a rename, no functional change.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200129203709.30493-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When the tap array in the driver is too low, this is not a warning but
an error. Also _once is not helpful, we should make sure it is
prominently in the logs. It is safe to do this because this will only
show up during SoC enablement when we a new SoCs needs more taps (if
that ever will happen).
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200129203709.30493-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move Renesas specific code for executing the tuning with a SCC into the
SDHI driver and leave only a generic call in the TMIO driver. Simplify
the code a little by removing init_tuning() and prepare_tuning()
callbacks. The latter is directly folded into the new execute_tuning()
callbacks.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200129203709.30493-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use increasing BIT numbers consistently and remove some superfluous
comments.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191217114034.13290-6-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
HW engineers say that automatic tap correction cannot be used for HS400
in all R-Car Gen3 SoCs. So, check for that SDHI variant and disable it
when HS400 is about to be enabled.
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20191217114034.13290-5-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
R-Car Gen3 cannot use correction error status with HS400.
HS200: CMD and DAT signal timing are based on CLK signal.
HS400: CMD signal is based on CLK. DAT signal is based on DS signal.
In HS400, CMD signal is 200MHz(SDR). DAT signal is 200MHz(DDR).
Center position of signal is different between CMD and DAT.
TAP position should be adjusted to the center position of CMD signal.
DAT sampling timing is adjusted by HS400 calibration circuit regardless
of TAP position. Refer to renesas_sdhi_adjust_hs400mode_enable().
However, correction error status contains CMD and DAT status in HS400
(DAT signal is not masked in HS400). Therefore, correction error status
cannot use in HS400. It means that auto correction cannot be uses in
HS400. Manual correction can change to the correct TAP position by
ignoring DAT correction error status and using only CMD correction
status.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[wsa: refactored patch from BSP]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191217114034.13290-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a manual correction mechanism for SDHI. Currently, SDHI
uses automatic TAP position correction. However, TAP position can also
be corrected manually via correction error status flags.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20191217114034.13290-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
hw_reset() clears the automatic correction bit twice. I couldn't find
anything in the docs recommending that. Removing one of them didn't
cause any regressions here, so keep it simple.
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20191217114034.13290-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The TX/RX register should not be treated the same way to allow for better
support of tuning. Fix this by using a default initial value for TX.
Signed-off-by: Ricky Wu <ricky_wu@realtek.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200316025232.1167-1-ricky_wu@realtek.com
[Ulf: Updated changelog]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SAMA5D2x doesn't drive CMD line if GPIO is used as CD line (at least
SAMA5D27 doesn't). Fix this by forcing card-detect in the module
if module-controlled CD is not used.
Fixed commit addresses the problem only for non-removable cards. This
amends it to also cover gpio-cd case.
Cc: stable@vger.kernel.org
Fixes: 7a1e3f1431 ("mmc: sdhci-of-at91: force card detect value for non removable devices")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/8d10950d9940468577daef4772b82a071b204716.1584290561.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI_PRESET_FOR_* registers are not set for the UniPhier platform
integration. (They are all read as zeros).
Set the SDHCI_QUIRK2_PRESET_VALUE_BROKEN quirk flag. Otherwise, the
High Speed DDR mode on the eMMC controller (MMC_TIMING_MMC_DDR52)
would not work.
I split the platform data to give no impact to other platforms,
although the UniPhier platform is currently only the upstream user
of this IP.
The SDHCI_QUIRK2_PRESET_VALUE_BROKEN flag is set if the compatible
string matches to "socionext,uniphier-sd4hc".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200312104257.21017-1-yamada.masahiro@socionext.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On the Acer Aspire Switch 10 (SW5-012) microSD slot always reports the card
being write-protected even though microSD cards do not have a write-protect
switch at all.
Add a new DMI_QUIRK_SD_NO_WRITE_PROTECT quirk which when set sets
the MMC_CAP2_NO_WRITE_PROTECT flag on the controller for the external SD
slot; and add a DMI quirk table entry which selects this quirk for the
Acer SW5-012.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200316184753.393458-2-hdegoede@redhat.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Based on a sample of 7 DSDTs from Cherry Trail devices using an AXP288
PMIC depending on the design one of 2 possible LDOs on the PMIC is used
for the MMC signalling voltage, either DLDO3 or GPIO1LDO (GPIO1 pin in
low noise LDO mode).
The Lenovo Miix 320-10ICR uses GPIO1LDO in the SHC1 ACPI device's DSM
methods to set 3.3 or 1.8 signalling voltage and this appears to work
as advertised, so presumably the device is actually using GPIO1LDO for
the external microSD signalling voltage.
But this device has a bug in the _PS0 method of the SHC1 ACPI device,
the DSM remembers the last set signalling voltage and the _PS0 restores
this after a (runtime) suspend-resume cycle, but it "restores" the voltage
on DLDO3 instead of setting it on GPIO1LDO as the DSM method does. DLDO3
is used for the LCD and setting it to 1.8V causes the LCD to go black.
This commit works around this issue by calling the Intel DSM to reset the
signal voltage to 3.3V after the host has been runtime suspended.
This will make the _PS0 method reprogram the DLDO3 voltage to 3.3V, which
leaves it at its original setting fixing the LCD going black.
This commit adds and uses a DMI quirk mechanism to only trigger this
workaround on the Lenovo Miix 320 while leaving the behavior of the
driver unchanged on other devices.
BugLink: https://bugs.freedesktop.org/show_bug.cgi?id=111294
BugLink: https://gitlab.freedesktop.org/drm/intel/issues/355
Reported-by: russianneuromancer <russianneuromancer@ya.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200316184753.393458-1-hdegoede@redhat.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The busy timeout for the CMD5 to put the eMMC into sleep state, is specific
to the card. Potentially the timeout may exceed the host->max_busy_timeout.
If that becomes the case, mmc_sleep() converts from using an R1B response
to an R1 response, as to prevent the host from doing HW busy detection.
However, it has turned out that some hosts requires an R1B response no
matter what, so let's respect that via checking MMC_CAP_NEED_RSP_BUSY. Note
that, if the R1B gets enforced, the host becomes fully responsible of
managing the needed busy timeout, in one way or the other.
Suggested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200311092036.16084-1-ulf.hansson@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It has turned out that the sdhci-tegra controller requires the R1B response,
for commands that has this response associated with them. So, converting
from an R1B to an R1 response for a CMD6 for example, leads to problems
with the HW busy detection support.
Fix this by informing the mmc core about the requirement, via setting the
host cap, MMC_CAP_NEED_RSP_BUSY.
Reported-by: Bitan Biswas <bbiswas@nvidia.com>
Reported-by: Peter Geis <pgwipeout@gmail.com>
Suggested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Cc: <stable@vger.kernel.org>
Tested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Tested-By: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It has turned out that the sdhci-omap controller requires the R1B response,
for commands that has this response associated with them. So, converting
from an R1B to an R1 response for a CMD6 for example, leads to problems
with the HW busy detection support.
Fix this by informing the mmc core about the requirement, via setting the
host cap, MMC_CAP_NEED_RSP_BUSY.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Reported-by: Anders Roxell <anders.roxell@linaro.org>
Reported-by: Faiz Abbas <faiz_abbas@ti.com>
Cc: <stable@vger.kernel.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Tested-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The busy timeout that is computed for each erase/trim/discard operation,
can become quite long and may thus exceed the host->max_busy_timeout. If
that becomes the case, mmc_do_erase() converts from using an R1B response
to an R1 response, as to prevent the host from doing HW busy detection.
However, it has turned out that some hosts requires an R1B response no
matter what, so let's respect that via checking MMC_CAP_NEED_RSP_BUSY. Note
that, if the R1B gets enforced, the host becomes fully responsible of
managing the needed busy timeout, in one way or the other.
Suggested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Cc: <stable@vger.kernel.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Tested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Tested-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-By: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It has turned out that some host controllers can't use R1B for CMD6 and
other commands that have R1B associated with them. Therefore invent a new
host cap, MMC_CAP_NEED_RSP_BUSY to let them specify this.
In __mmc_switch(), let's check the flag and use it to prevent R1B responses
from being converted into R1. Note that, this also means that the host are
on its own, when it comes to manage the busy timeout.
Suggested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Cc: <stable@vger.kernel.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Tested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Tested-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-By: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable MSI interrupt for GL9750/GL9755. Some platforms
do not support PCI INTx and devices can not work without
interrupt. Like messages below:
[ 4.487132] sdhci-pci 0000:01:00.0: SDHCI controller found [17a0:9755] (rev 0)
[ 4.487198] ACPI BIOS Error (bug): Could not resolve symbol [\_SB.PCI0.PBR2._PRT.APS2], AE_NOT_FOUND (20190816/psargs-330)
[ 4.487397] ACPI Error: Aborting method \_SB.PCI0.PBR2._PRT due to previous error (AE_NOT_FOUND) (20190816/psparse-529)
[ 4.487707] pcieport 0000:00:01.3: can't derive routing for PCI INT A
[ 4.487709] sdhci-pci 0000:01:00.0: PCI INT A: no GSI
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Tested-by: Raul E Rangel <rrangel@chromium.org>
Fixes: e51df6ce66 ("mmc: host: sdhci-pci: Add Genesys Logic GL975x support")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200219092900.9151-1-benchuanggli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Call cpu_latency_qos_add/remove_request() instead of
pm_qos_add/remove_request(), respectively, because the
latter are going to be dropped.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
This function is not exported and only used in this file. Mark it static.
Cc: Ritesh Harjani <riteshh@codeaurora.org>
Cc: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Fixes: 87a8df0dce ("mmc: sdhci-msm: Add CQHCI support for sdhci-msm")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200206162124.201195-1-swboyd@chromium.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- remove ioremap_nocache given that is is equivalent to
ioremap everywhere
-----BEGIN PGP SIGNATURE-----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=TUCJ
-----END PGP SIGNATURE-----
Merge tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap
Pull ioremap updates from Christoph Hellwig:
"Remove the ioremap_nocache API (plus wrappers) that are always
identical to ioremap"
* tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap:
remove ioremap_nocache and devm_ioremap_nocache
MIPS: define ioremap_nocache to ioremap
All callers of __mmc_switch() should now be specifying a valid timeout for
the CMD6 command. However, just to be sure, let's print a warning and
default to use the generic_cmd6_time in case the provided timeout_ms
argument is zero.
In this context, let's also simplify some of the corresponding code and
clarify some related comments.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200122142747.5690-4-ulf.hansson@linaro.org
The INAND_CMD38_ARG_EXT_CSD is a vendor specific EXT_CSD register, which is
used to prepare an erase/trim operation. However, it doesn't make sense to
use a timeout of 10 minutes while updating the register, which becomes the
case when the timeout_ms argument for mmc_switch() is set to zero.
Instead, let's use the generic_cmd6_time, as that seems like a reasonable
timeout to use for these cases.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200122142747.5690-3-ulf.hansson@linaro.org
The timeout values used while waiting for a CMD6 for BKOPS or a CACHE_FLUSH
to complete, are not defined by the eMMC spec. However, a timeout of 10
minutes as is currently being used, is just silly for both of these cases.
Instead, let's specify more reasonable timeouts, 120s for BKOPS and 30s for
CACHE_FLUSH.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200122142747.5690-2-ulf.hansson@linaro.org
'static inline' in .c files does not make much sense because
functions may or may not be inlined irrespective of the 'inline'
marker. It is just a hint.
This function is quite small, so very likely to be inlined by the
compiler's optimization (-O2 or -Os), but it is up to the compiler
after all.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200121105858.13325-1-yamada.masahiro@socionext.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let a vendor driver supply the maximum descriptor size that it
can operate on. ADMA descriptor table would be allocated using this
supplied size.
If any SD Host controller is of version prior to v4.10 spec
but supports 16byte descriptor, this change allows them to supply
correct descriptor size for ADMA table allocation.
Also let a vendor driver update the descriptor size by overriding
sdhc_host->desc_size if it has to operates on a different descriptor
sizes in different conditions.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1579531122-28341-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch is to fix a serious issue that clock is always disabled
in esdhc_of_set_clock().
Fixes: 1b21a701ae ("mmc: sdhci-of-esdhc: fix clock setting for different controller versions")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Link: https://lore.kernel.org/r/20200120094835.28050-1-yangbo.lu@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The standard SD controller uses two 16-bit registers for
command sending.
0xC: Transfer Mode Register
0xE: Command Register
But the eSDHC controller uses one 32-bit register instead.
0xC: XFERTYPE
For Transfer Mode Register and Command Register writing,
the eSDHC driver will store Transfer Mode Register value in
a variable first. When Command Register writing happens,
driver will directly write a 32-bit value into XFERTYPE
register.
But for Transfer Mode Register reading, driver just returns
a actual value. This may cause issue for some read-modify-write
operations. We should make both reading and write on that variable
for Transfer Mode Register.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Link: https://lore.kernel.org/r/20200117063858.37296-1-yangbo.lu@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When switching from any MMC speed mode that requires 1.8v
(HS200, HS400 and HS400ES) to High Speed (HS) mode, the system
ends up configured for SDR12 with a 50MHz clock which is an illegal
mode.
This happens because the SDHCI_CTRL_VDD_180 bit in the
SDHCI_HOST_CONTROL2 register is left set and when this bit is
set, the speed mode is controlled by the SDHCI_CTRL_UHS field
in the SDHCI_HOST_CONTROL2 register. The SDHCI_CTRL_UHS field
will end up being set to 0 (SDR12) by sdhci_set_uhs_signaling()
because there is no UHS mode being set.
The fix is to change sdhci_set_uhs_signaling() to set the
SDHCI_CTRL_UHS field to SDR25 (which is the same as HS) for
any switch to HS mode.
This was found on a new eMMC controller that does strict checking
of the speed mode and the corresponding clock rate. It caused the
switch to HS400 mode to fail because part of the sequence to switch
to HS400 requires a switch from HS200 to HS before going to HS400.
This issue was previously fixed by commit c894e33ddc ("mmc: sdhci:
Fix incorrect switch to HS mode") and later removed by commit
07bcc41156 ("Revert \"mmc: sdhci: Fix incorrect switch to HS mode\"")
because it caused failures with some SD cards on AM65X systems. The
fix will now be done in a platform specific callback instead of
common sdhci code.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200113210706.11972-7-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Shutdown controller and disable it's clocks to insure max power
savings in S5 on systems that leave power on.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Link: https://lore.kernel.org/r/20200113210706.11972-5-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The new SCMI clock protocol driver does not get probed that early in
boot. Brcmstb drivers typically have the following code when getting
a clock:
priv->clk = devm_clk_get(&pdev->dev, NULL);
if (IS_ERR(priv->clk)) {
dev_err(&pdev->dev, "Clock not found in Device Tree\n");
priv->clk = NULL;
}
This commit changes the driver to do what is below.
priv->clk = devm_clk_get(&pdev->dev, NULL);
if (IS_ERR(priv->clk)) {
if (PTR_ERR(priv->clk) == -EPROBE_DEFER)
return -EPROBE_DEFER;
dev_err(&pdev->dev, "Clock not found in Device Tree\n");
priv->clk = NULL;
}
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Link: https://lore.kernel.org/r/20200113210706.11972-4-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The latest eMMC JEDEC specification version 5.1 added a new
transfer mode, HS400 with enhanced strobe (HS400ES). This mode
will be selected if both the host controller and eMMC device
support it. The latest Arasan 5.1 controller in the 7216a0
supports this mode. The "Host Controller Specification" has
not been updated so the controller register bit used to enable
this mode is not specified and varies the with controller vendor.
The Linux SDHCI driver supplies a callback for enabling HS400ES
mode and that callback will be used to supply a routine that
will set the proper bit in the Arasan Vendor register.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Link: https://lore.kernel.org/r/20200113210706.11972-3-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
platform_get_irq() will call dev_err() itself on failure,
so there is no need for the driver to also do this.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200116144322.57308-1-yuehaibing@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix an issue reported by sparse, since mixed types of parameters are
used on calling dmaengine_prep_slave_sg().
Fixes: 36e1da441fec (mmc: sdhci: add support for using external DMA devices)
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200120033223.897-1-zhang.chunyan@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For SDHCIv3+ with programmable clock mode, minimal clock frequency is
still base clock / max(divider). Minimal programmable clock frequency is
always greater than minimal divided clock frequency. Without this patch,
SDHCI uses out-of-spec initial frequency when multiplier is big enough:
mmc1: mmc_rescan_try_freq: trying to init card at 468750 Hz
[for 480 MHz source clock divided by 1024]
The code in sdhci_calc_clk() already chooses a correct SDCLK clock mode.
Fixes: c3ed387762 ("mmc: sdhci: add support for programmable clock mode")
Cc: <stable@vger.kernel.org> # 4f6aa3264af4: mmc: tegra: Only advertise UHS modes if IO regulator is present
Cc: <stable@vger.kernel.org>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/ffb489519a446caffe7a0a05c4b9372bd52397bb.1579082031.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some omap controllers need software to monitor a 0->1->0 for software
reset. Add a SDHCI_OMAP_SPECIAL_RESET flag to indicate this.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200116105154.7685-11-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for new compatible for TI's am335x and am437x devices.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200116105154.7685-10-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Disable data timeout interrupt during an erase operation.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200116105154.7685-8-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Refactor sdhci_set_timeout() such that platform drivers can do some
functionality in a set_timeout() callback and then call
__sdhci_set_timeout() to complete the operation.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200116105154.7685-7-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Export sdhci_set_timeout_irq() so that it is accessible from platform drivers.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200116105154.7685-6-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci-omap can support both external dma controller via dmaengine framework
as well as ADMA which standard SD host controller provides.
Fixes by Faiz Abbas <fazi_abbas@ti.com>:
1. Switch to DMA slave mode when using external DMA
2. Add offset to mapbase
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200116105154.7685-5-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some standard SD host controllers can support both external dma
controllers as well as ADMA/SDMA in which the SD host controller
acts as DMA master. TI's omap controller is the case as an example.
Currently the generic SDHCI code supports ADMA/SDMA integrated in
the host controller but does not have any support for external DMA
controllers implemented using dmaengine, meaning that custom code is
needed for any systems that use an external DMA controller with SDHCI.
Fixes by Faiz Abbas <faiz_abbas@ti.com>:
1. Map scatterlists before dmaengine_prep_slave_sg()
2. Use dma_async() functions inside of the send_command() path and call
terminate_sync() in non-atomic context in case of an error.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200116105154.7685-4-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for adding external dma support, factor out data initialization,
block info and mrq_done to their own functions.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200116105154.7685-3-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_alloc_host() does its work not using managed infrastructure, so
needs explicit free on error path. Add it where needed.
Cc: <stable@vger.kernel.org>
Fixes: bb5f8ea4d5 ("mmc: sdhci-of-at91: introduce driver for the Atmel SDMMC")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/b2a44d5be2e06ff075f32477e466598bb0f07b36.1577961679.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Command Queuing was enabled completely for J721e controllers which lead
to partial enablement even for Am65x. Complete CQ implementation for
AM65x by adding the irq callback.
Fixes: f545702b74 ("mmc: sdhci_am654: Add Support for Command Queuing Engine to J721E")
Cc: stable@vger.kernel.org
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200108143301.1929-4-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The tuning data is leftover in the buffer after tuning. This can cause
issues in future data commands, especially with CQHCI. Reset the command
and data lines after tuning to continue from a clean state.
Fixes: 41fd4caeb0 ("mmc: sdhci_am654: Add Initial Support for AM654 SDHCI driver")
Cc: stable@vger.kernel.org
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200108143301.1929-3-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC/SD controllers on am65x and j721e don't in fact detect the write
protect line as inverted. No issues were detected because of this
because the sdwp line is not connected on any of the evms. Fix this by
removing the flag.
Fixes: 1accbced1c ("mmc: sdhci_am654: Add Support for 4 bit IP on J721E")
Cc: stable@vger.kernel.org
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200108143301.1929-2-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch is to fix clock setting code for different controller
versions. Two of HW changes after vendor version 2.2 are removing
PEREN/HCKEN/IPGEN bits in system control register, and adding SD
clock stable bit in present state register. This patch cleans up
related code too.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Link: https://lore.kernel.org/r/20200108040713.38888-2-yangbo.lu@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch is to fix operating in esdhc_reset() for different
controller versions, and to add bus-width restoring after data
reset for eSDHC (verdor version <= 2.2).
Also add annotation for understanding.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200108040713.38888-1-yangbo.lu@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is an official update for eSDHC tuning erratum A-008171.
This patch is to implement the changes,
- Affect all revisions of SoC.
- Changes for tuning window checking.
- Hardware hits a new condition that tuning succeeds although
the eSDHC might not have tuned properly for type2 SoCs
(soc_tuning_erratum_type2[] array in driver). So check
tuning window after tuning succeeds.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20191212075219.48625-2-yangbo.lu@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Convert to use a new function esdhc_tuning_window_ptr() to
get tuning window start point and end point.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20191212075219.48625-1-yangbo.lu@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20191217122254.7103-1-peter.ujfalusi@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA if needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191217113114.32085-1-peter.ujfalusi@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA if needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191217113031.31847-1-peter.ujfalusi@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191217113004.31688-1-peter.ujfalusi@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191217112934.31535-1-peter.ujfalusi@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191217112847.31351-1-peter.ujfalusi@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191217112803.31161-1-peter.ujfalusi@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191217112737.31024-1-peter.ujfalusi@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191217112656.30860-1-peter.ujfalusi@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The erratum A-009204 workaround patch was reverted because of
incorrect implementation.
8b6dc6b mmc: sdhci-of-esdhc: Revert "mmc: sdhci-of-esdhc: add
erratum A-009204 support"
This patch is to re-implement the workaround (add a 5 ms delay
before setting SYSCTL[RSTD] to make sure all the DMA transfers
are finished).
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Link: https://lore.kernel.org/r/20191219032335.26528-1-yangbo.lu@nxp.com
Fixes: 5dd1955225 ("mmc: sdhci-of-esdhc: add erratum A-009204 support")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For the ux500v2 variant of the PL18x block, any block sizes
are supported. This is necessary to support some SDIO
transfers. This also affects the QCOM MMCI variant and the
ST micro variant.
For Ux500 an additional quirk only allowing DMA on blocks
that are a power of two is needed. This might be a bug in
the DMA engine (DMA40) or the MMCI or in the interconnect,
but the most likely is the MMCI, as transfers of these
sizes work fine for other devices using the same DMA
engine. DMA works fine also with SDIO as long as the
blocksize is a power of 2.
This patch has proven necessary for enabling SDIO for WLAN on
PostmarketOS-based Ux500 platforms.
What we managed to test in practice is Broadcom WiFi over
SDIO on the Ux500 based Samsung GT-I8190 and GT-S7710.
This WiFi chip, BCM4334 works fine after the patch.
Before this patch:
brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4334-sdio
for chip BCM4334/3
mmci-pl18x 80118000.sdi1_per2: unsupported block size (60 bytes)
brcmfmac: brcmf_sdiod_ramrw: membytes transfer failed
brcmfmac: brcmf_sdio_download_code_file: error -22 on writing
434236 membytes at 0x00000000
brcmfmac: brcmf_sdio_download_firmware: dongle image file download
failed
After this patch:
brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4334/3 wl0:
Nov 21 2012 00:21:28 version 6.10.58.813 (B2) FWID 01-0
Bringing up networks, discovering networks with "iw dev wlan0 scan"
and connecting works fine from this point.
This patch is inspired by Ulf Hansson's patch
http://www.spinics.net/lists/linux-mmc/msg12160.html
As the DMA engines on these platforms may now get block sizes
they were not used to before, make sure to also respect if
the DMA engine says "no" to a transfer.
Make a drive-by fix for datactrl_blocksz, misspelled.
Cc: Ludovic Barre <ludovic.barre@st.com>
Cc: Brian Masney <masneyb@onstation.org>
Cc: Stephan Gerhold <stephan@gerhold.net>
Cc: Niklas Cassel <niklas.cassel@linaro.org>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20191217143952.2885-1-linus.walleij@linaro.org
platform_get_resource(pdev, IORESOURCE_IRQ) is not recommended for
requesting IRQ's resources, as they can be not ready yet. Using
platform_get_irq() instead is preferred for getting IRQ even if it
was not retrieved earlier.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Link: https://lore.kernel.org/r/20191215175120.3290-13-tiny.windzz@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20191215175120.3290-6-tiny.windzz@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20191215175120.3290-2-tiny.windzz@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Command queuing has been reported broken on some systems based on Intel
GLK. A separate patch disables command queuing in some cases.
This patch adds a quirk for broken command queuing, which enables users
with problems to disable command queuing using sdhci module parameters for
quirks.
Fixes: 8ee82bda23 ("mmc: sdhci-pci: Add CQHCI support for Intel GLK")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191217095349.14592-2-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Command queuing has been reported broken on some Lenovo systems based on
Intel GLK. This is likely a BIOS issue, so disable command queuing for
Intel GLK if the BIOS vendor string is "LENOVO".
Fixes: 8ee82bda23 ("mmc: sdhci-pci: Add CQHCI support for Intel GLK")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191217095349.14592-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Two previous patches introduced below quirks for P2020 platforms.
- SDHCI_QUIRK_RESET_AFTER_REQUEST
- SDHCI_QUIRK_BROKEN_TIMEOUT_VAL
The patches made a mistake to add them in quirks2 of sdhci_host
structure, while they were defined for quirks.
host->quirks2 |= SDHCI_QUIRK_RESET_AFTER_REQUEST;
host->quirks2 |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL;
This patch is to fix them.
host->quirks |= SDHCI_QUIRK_RESET_AFTER_REQUEST;
host->quirks |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL;
Fixes: 05cb6b2a66 ("mmc: sdhci-of-esdhc: add erratum eSDHC-A001 and A-008358 support")
Fixes: a46e427125 ("mmc: sdhci-of-esdhc: add erratum eSDHC5 support")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191216031842.40068-1-yangbo.lu@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The stm32_sdmmc variant has build-in support for datatimeout for R1B
requests. If a corresponding IRQ is raised, this triggers the DPSM to stay
busy and remains in a non-functional state. Only a reset can bring it back
to a functional state.
Because a reset must be issued from non-atomic context, let's defer this to
be managed from a threaded IRQ handler. Besides the reset, the threaded
handler also calls mmc_request_done(), to finally complete the request.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20191211133934.16932-1-ludovic.Barre@st.com
[Ulf: A few minor updates to the changelog/comments]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are a few places around the code that invert inverted and possibly
inverted CD line. That's really confusing. Squash them all into one place
in mmc_gpiod_request_cd(). MMC_CAP2_CD_ACTIVE_HIGH is used analogously to
WP line: in GPIO mode it is used only at probe time to switch polarity, for
native mode it is left as is.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/db189b715596d63caf8c6a088bddc71dd69a879b.1576031637.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use MMC_CAP2_RO_ACTIVE_HIGH flag as indicator if GPIO line is to be
inverted compared to DT/platform-specified polarity. The flag is not used
after init in GPIO mode anyway. No functional changes intended.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/a60f563f11bbff821da2fa2949ca82922b144860.1576031637.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver forgets to call pci_release_regions() in probe failure
and remove.
Add the missed calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191206075408.18355-1-hslester96@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge an immutable pinctrl branch from Linus Walleij's tree, which enables
pinctrl code consolidations for mmc.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let's drop the boilerplate code for managing the default pinctrl state and
convert into using the new pinctrl_select_default_state().
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191206170821.29711-10-ulf.hansson@linaro.org
Let's move away from using pinctrl_pm_select_default_state() as it's
scheduled for removal and use pinctrl_select_default_state() instead.
Cc: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191206170821.29711-9-ulf.hansson@linaro.org
Let's move away from using pinctrl_pm_select_default_state() as it's
scheduled for removal and use pinctrl_select_default_state() instead.
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191206170821.29711-8-ulf.hansson@linaro.org
Let's drop the boilerplate code for managing the default pinctrl state and
convert into using the new pinctrl_select_default_state().
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191206170821.29711-7-ulf.hansson@linaro.org
Let's drop the boilerplate code for managing the default pinctrl state and
convert into using the new pinctrl_select_default_state().
Additionally, move away from using pinctrl_pm_select_default_state() as
it's scheduled for removal and use pinctrl_select_default_state() instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191206170821.29711-6-ulf.hansson@linaro.org
Let's drop the boilerplate code for managing the default pinctrl state and
convert into using the new pinctrl_select_default_state().
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Lars Persson <lars.persson@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191206170821.29711-5-ulf.hansson@linaro.org
Let's drop the boilerplate code for managing the default pinctrl state and
convert into using the new pinctrl_select_default_state().
Additionally, move away from using pinctrl_pm_select_default_state() as
it's scheduled for removal and use pinctrl_select_default_state() instead.
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191206170821.29711-4-ulf.hansson@linaro.org
Let's drop the boilerplate code for managing the default pinctrl state and
convert into using the new pinctrl_select_default_state().
Cc: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191206170821.29711-3-ulf.hansson@linaro.org
Tuning support in DDR50 speed mode was added in SD Specifications Part1
Physical Layer Specification v3.01. Its not possible to distinguish
between v3.00 and v3.01 from the SCR and that is why since
commit 4324f6de6d ("mmc: core: enable CMD19 tuning for DDR50 mode")
tuning failures are ignored in DDR50 speed mode.
Cards compatible with v3.00 don't respond to CMD19 in DDR50 and this
error gets printed during enumeration and also if retune is triggered at
any time during operation. Update the printk level to pr_debug so that
these errors don't lead to false error reports.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Cc: stable@vger.kernel.org # v4.4+
Link: https://lore.kernel.org/r/20191206114326.15856-1-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
New datasheets require different and new values for HS400 with 4taps or
8taps.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191203200513.1758-6-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that the quirks structure is accessible, we can remove the TMIO flag
for HS400 using only 4 taps. This is Renesas specific anyhow.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191203200513.1758-5-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We will need that for a later patch.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191203200513.1758-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The warning is not solely used for SDR104 anymore, but for all which
require tuning.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191203200513.1758-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The two devices next to each other are super similar, but still, let's
keep the alphanumeric sorting for easier additions later.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191203200513.1758-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We know now that there won't be Gen3 SoCs with both, SYS-DMAC and
internal DMAC. We removed the blacklisting for SYS-DMAC already, so we
can remove the whitelisting for internal DMAC, too. This makes adding
new SoCs easier. We keep the quirk handling, of course.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191203194859.917-1-wsa@the-dreams.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The STOP command is disabled for multiple blocks r/w commands
with auto CMD12, when start to send. However, if there is data
error, software still needs to send CMD12 according to SD spec.
This patch is to allow software CMD12 sending for this case.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20191114111814.35199-1-yangbo.lu@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The code in mmc_spi_initsequence() tries to send a burst with
high chipselect and for this reason hardcodes the device into
SPI_CS_HIGH.
This is not good because the SPI_CS_HIGH flag indicates
logical "asserted" CS not always the physical level. In
some cases the signal is inverted in the GPIO library and
in that case SPI_CS_HIGH is already set, and enforcing
SPI_CS_HIGH again will actually drive it low.
Instead of hard-coding this, toggle the polarity so if the
default is LOW it goes high to assert chipselect but if it
is already high then toggle it low instead.
Cc: Phil Elwell <phil@raspberrypi.org>
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20191204152749.12652-1-linus.walleij@linaro.org
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the SAM9x60 SoC, there are only two clocks instead of three for the
SDHCI device. The base clk is no longer provided, it is generated
internally from the mult clk.
The values of the base clk and mul in the capabilities registers may not
reflect the reality as the mult clk is a programmable clock which can take
several rates. As we can't trust those values, take them from the clock
tree and update the capabilities according to.
As we can have the same pitfall, in some cases, with the SAMA5D2 Soc,
stop relying on capabilities too.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20191128074522.69706-2-ludovic.desroches@microchip.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tuning support in DDR50 speed mode was added in SD Specifications Part1
Physical Layer Specification v3.01. Its not possible to distinguish
between v3.00 and v3.01 from the SCR and that is why since
commit 4324f6de6d ("mmc: core: enable CMD19 tuning for DDR50 mode")
tuning failures are ignored in DDR50 speed mode.
Cards compatible with v3.00 don't respond to CMD19 in DDR50 and this
error gets printed during enumeration and also if retune is triggered at
any time during operation. Update the printk level to pr_debug so that
these errors don't lead to false error reports.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Cc: stable@vger.kernel.org # v4.4+
Link: https://lore.kernel.org/r/20191206114326.15856-1-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit 5dd1955225.
First, the fix seems to be plain wrong, since the erratum suggests
waiting 5ms before setting setting SYSCTL[RSTD], but this msleep()
happens after the call of sdhci_reset() which is where that bit gets
set (if SDHCI_RESET_DATA is in mask).
Second, walking the whole device tree to figure out if some node has a
"fsl,p2020-esdhc" compatible string is hugely expensive - about 70 to
100 us on our mpc8309 board. Walking the device tree is done under a
raw_spin_lock, so this is obviously really bad on an -rt system, and a
waste of time on all.
In fact, since esdhc_reset() seems to get called around 100 times per
second, that mpc8309 now spends 0.8% of its time determining that
it is not a p2020. Whether those 100 calls/s are normal or due to some
other bug or misconfiguration, regularly hitting a 100 us
non-preemptible window is unacceptable.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191204085447.27491-1-linux@rasmusvillemoes.dk
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
there is a chance that always get response CRC error after HS200 tuning,
the reason is that need set CMD_TA to 2. this modification is only for
MT8173.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Cc: stable@vger.kernel.org
Fixes: 1ede5cb88a ("mmc: mediatek: Use data tune for CMD line tune")
Link: https://lore.kernel.org/r/20191204071958.18553-1-chaotian.jing@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The DDR_CONFIG register offset got updated after a specific
minor version of sdcc V4. This offset change has not been properly
taken care of while updating register changes for sdcc V5.
Correcting proper offset for this register.
Also updating this register value to reflect the recommended RCLK
delay.
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/0101016ea738ec72-fa0f852d-20f8-474a-80b2-4b0ef63b132c-000000@us-west-2.amazonses.com
Fixes: f15358885d ("mmc: sdhci-msm: Define new Register address map")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit c894e33ddc.
This commit aims to treat SD High speed and SDR25 as the same while
setting UHS Timings in HOST_CONTROL2 which leads to failures with some
SD cards in AM65x. Revert this commit.
The issue this commit was trying to fix can be implemented in a platform
specific callback instead of common sdhci code.
Cc: <stable@vger.kernel.org>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20191128110422.25917-1-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Here is the "big" set of driver core patches for 5.5-rc1
There's a few minor cleanups and fixes in here, but the majority of the
patches in here fall into two buckets:
- debugfs api cleanups and fixes
- driver core device link support for boot dependancy issues
The debugfs api cleanups are working to slowly refactor the debugfs apis
so that it is even harder to use incorrectly. That work has been
happening for the past few kernel releases and will continue over time,
it's a long-term project/goal
The driver core device link support missed 5.4 by just a bit, so it's
been sitting and baking for many months now. It's from Saravana Kannan
to help resolve the problems that DT-based systems have at boot time
with dependancy graphs and kernel modules. Turns out that no one has
actually tried to build a generic arm64 kernel with loads of modules and
have it "just work" for a variety of platforms (like a distro kernel)
The big problem turned out to be a lack of depandancy information
between different areas of DT entries, and the work here resolves that
problem and now allows devices to boot properly, and quicker than a
monolith kernel.
All of these patches have been in linux-next for a long time with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXd6m6Q8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yntJQCcCqg6RQ7LTdHuZv1ETeefXlsfk00An1Jtean6
42bWGx52bGFvAcpjWy8R
=P7hq
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the "big" set of driver core patches for 5.5-rc1
There's a few minor cleanups and fixes in here, but the majority of
the patches in here fall into two buckets:
- debugfs api cleanups and fixes
- driver core device link support for boot dependancy issues
The debugfs api cleanups are working to slowly refactor the debugfs
apis so that it is even harder to use incorrectly. That work has been
happening for the past few kernel releases and will continue over
time, it's a long-term project/goal
The driver core device link support missed 5.4 by just a bit, so it's
been sitting and baking for many months now. It's from Saravana Kannan
to help resolve the problems that DT-based systems have at boot time
with dependancy graphs and kernel modules. Turns out that no one has
actually tried to build a generic arm64 kernel with loads of modules
and have it "just work" for a variety of platforms (like a distro
kernel). The big problem turned out to be a lack of dependency
information between different areas of DT entries, and the work here
resolves that problem and now allows devices to boot properly, and
quicker than a monolith kernel.
All of these patches have been in linux-next for a long time with no
reported issues"
* tag 'driver-core-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (68 commits)
tracing: Remove unnecessary DEBUG_FS dependency
of: property: Add device link support for interrupt-parent, dmas and -gpio(s)
debugfs: Fix !DEBUG_FS debugfs_create_automount
of: property: Add device link support for "iommu-map"
of: property: Fix the semantics of of_is_ancestor_of()
i2c: of: Populate fwnode in of_i2c_get_board_info()
drivers: base: Fix Kconfig indentation
firmware_loader: Fix labels with comma for builtin firmware
driver core: Allow device link operations inside sync_state()
driver core: platform: Declare ret variable only once
cpu-topology: declare parse_acpi_topology in <linux/arch_topology.h>
crypto: hisilicon: no need to check return value of debugfs_create functions
driver core: platform: use the correct callback type for bus_find_device
firmware_class: make firmware caching configurable
driver core: Clarify documentation for fwnode_operations.add_links()
mailbox: tegra: Fix superfluous IRQ error message
net: caif: Fix debugfs on 64-bit platforms
mac80211: Use debugfs_create_xul() helper
media: c8sectpfe: no need to check return value of debugfs_create functions
of: property: Add device link support for iommus, mboxes and io-channels
...
- Add CMD13 polling for MMC IOCTLS with R1B response.
- Add common DT properties for clk-phase-delays for various speed modes.
- Fix size overflow for mmc gp-partitions.
- Re-work HW reset for SDIO cards, which also includes a re-work for
Marvell's WiFi mwifiex SDIO func driver.
MMC host:
- jz4740: Add support for X1000 and JZ4760.
- jz4740: Add support for 8-bit bus and for low power mode.
- mmci: Add support for HW busy timeout for the stm32_sdmmc variant.
- owl-mmc: Add driver for Actions Semi Owl SoCs SD/MMC controller.
- renesas_sdhi: Add support for r8a774b1.
- sdhci_am654: Add support for Command Queuing Engine for J721E.
- sdhci-milbeaut: Add driver for the Milbeaut SD controller.
- sdhci-of-arasan: Add support for ZynqMP tap-delays.
- sdhci-of-arasan: Add support for clk-phase-delays for SD cards.
- sdhci-of-arasan: Add support for Intel LGM SDXC.
- sdhci-of-aspeed: Allow inversion of the internal card detect signal.
- sdhci-of-esdhc: Fixup workaround for erratum A-008171 for tunings.
- sdhci-of-at91: Improve support for calibration.
- sdhci-pci: Add support for Intel JSL.
- sdhci-pci: Add quirk for AMD SDHC Device 0x7906.
- tmio: Enable support for erase/discard/trim requests.
MMC/OMAP/pandora/wl1251:
The TI wl1251 WiFi driver for SDIO on the OMAP openpandora board has been
broken since v4.7. To fix the problems, changes have been made cross
subsystems, but also to OMAP2 machine code and to openpandora DTS files, as
summarized below. Note that, relevant changes have been tagged for stable.
- mmc/wl1251: Re-introduce lost SDIO quirks and vendor-id for wl1251
- omap/omap_hsmmc: Remove redundant platform config for openpandora
- omap_hsmmc: Initialize non-std SDIO card for wl1251 for pandora
- omap/dts/pandora: Specify wl1251 through a child node of mmc3
- wl1251: Add devicetree support for TI wl1251 SDIO
-----BEGIN PGP SIGNATURE-----
iQJLBAABCgA1FiEEugLDXPmKSktSkQsV/iaEJXNYjCkFAl3dRnAXHHVsZi5oYW5z
c29uQGxpbmFyby5vcmcACgkQ/iaEJXNYjClQqxAA0QFBhpdXMXPUv74wduxup4u/
JFKUBX81CvZ0XoES9Q6N96ZM+umaWo7mxKE0PhBPX4ScdcGvQTL7f7kqWamtUtd1
bKwgdEau1hyAAsAUMEUONw5+7Vyg3i5WXogItg+RqAefUXwW/KxeNBfBBC3kY/az
4/aRBFW2N52LMqOWndAbg2EdaX5nrTl72NXwecPXEsAPid0yoz7YUpBysLDdOVAm
3PYjz2R56wUfgXRpcMUWmSSkgAT6yicPAXtpGUsxZG5oFlOeEjaqB6ggDz9bj50z
aBNXBpx+vFKiXKqX3vru67tqKo8nS7JTS9qiTDIzQjsS47MML9dOEpKQlTBRklOg
z7XqQ8X8mic/YvQrxZO8c/pvZls/QZrssLfdy0edS/r4tbNC/NfPEkdi6wiXojPL
QZySR1Mt3De/3daZSqxYQcca82GVCTIpV/3wsRML/pAqsDaM/ZAHRbfYJ6ZdAHUN
bnZcr0gJ0uKDdwfaKewt5t/3TDftE5kb0UndlAi5xwffeKELQ0xTGrEaFlf0D7vr
QCIJBI6HIQ/AIuMDRg1LIV1aTmJ3Q0oGxLKNWf1NKjDZfpNkVqWSSkrx5GxQuq30
AdR4prTtAlzkCKrGLNDUer7hMCutv/UIXbmbuuoPXjR/qLCR41qLYYg/AC2KUOTW
ZT8iZBdcoK6frMzmRXU=
=WOaQ
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"These are the updates for MMC and MEMSTICK for v5.5.
Note that this also contains quite some additional changes reaching
beyond both the MMC and MEMSTICK subsystems. This is primarily because
of fixing an old regression for a WiFi driver based on the SDIO
interface on an OMAP openpandora board
MMC core:
- Add CMD13 polling for MMC IOCTLS with R1B response.
- Add common DT properties for clk-phase-delays for various speed
modes.
- Fix size overflow for mmc gp-partitions.
- Re-work HW reset for SDIO cards, which also includes a re-work for
Marvell's WiFi mwifiex SDIO func driver.
MMC host:
- jz4740: Add support for X1000 and JZ4760.
- jz4740: Add support for 8-bit bus and for low power mode.
- mmci: Add support for HW busy timeout for the stm32_sdmmc variant.
- owl-mmc: Add driver for Actions Semi Owl SoCs SD/MMC controller.
- renesas_sdhi: Add support for r8a774b1.
- sdhci_am654: Add support for Command Queuing Engine for J721E.
- sdhci-milbeaut: Add driver for the Milbeaut SD controller.
- sdhci-of-arasan: Add support for ZynqMP tap-delays.
- sdhci-of-arasan: Add support for clk-phase-delays for SD cards.
- sdhci-of-arasan: Add support for Intel LGM SDXC.
- sdhci-of-aspeed: Allow inversion of the internal card detect
signal.
- sdhci-of-esdhc: Fixup workaround for erratum A-008171 for tunings.
- sdhci-of-at91: Improve support for calibration.
- sdhci-pci: Add support for Intel JSL.
- sdhci-pci: Add quirk for AMD SDHC Device 0x7906.
- tmio: Enable support for erase/discard/trim requests.
MMC/OMAP/pandora/wl1251:
The TI wl1251 WiFi driver for SDIO on the OMAP openpandora board has
been broken since v4.7. To fix the problems, changes have been made
cross subsystems, but also to OMAP2 machine code and to openpandora
DTS files, as summarized below. Relevant changes have been tagged for
stable.
- mmc/wl1251: Re-introduce lost SDIO quirks and vendor-id for wl1251
- omap/omap_hsmmc: Remove redundant platform config for openpandora
- omap_hsmmc: Initialize non-std SDIO card for wl1251 for pandora
- omap/dts/pandora: Specify wl1251 through a child node of mmc3
- wl1251: Add devicetree support for TI wl1251 SDIO"
* tag 'mmc-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (73 commits)
dt-bindings: mmc: Correct the type of the clk phase properties
Revert "mmc: tmio: remove workaround for NON_REMOVABLE"
memstick: Fix Kconfig indentation
mmc: sdhci-of-arasan: Add support for ZynqMP Platform Tap Delays Setup
dt-bindings: mmc: arasan: Document 'xlnx,zynqmp-8.9a' controller
firmware: xilinx: Add SDIO Tap Delay nodes
mmc: sdhci-of-arasan: Add support to set clock phase delays for SD
dt-bindings: mmc: Add optional generic properties for mmc
mmc: sdhci-of-arasan: Add sampling clock for a phy to use
dt-bindings: mmc: arasan: Update Documentation for the input clock
mmc: sdhci-of-arasan: Separate out clk related data to another structure
mmc: sdhci: Fix grammar in warning message
mmc: sdhci-of-aspeed: add inversion signal presence
mmc: sdhci-of-aspeed: enable CONFIG_MMC_SDHCI_IO_ACCESSORS
mmc: sdhci_am654: Add Support for Command Queuing Engine to J721E
mmc: core: Fix size overflow for mmc partitions
mmc: tmio: Add MMC_CAP_ERASE to allow erase/discard/trim requests
net: wireless: ti: remove local VENDOR_ID and DEVICE_ID definitions
net: wireless: ti: wl1251 use new SDIO_VENDOR_ID_TI_WL1251 definition
mmc: core: fix wl1251 sdio quirks
...
- Update the ACPICA code in the kernel to upstream revision 20191018
including:
* Fixes for Clang warnings (Bob Moore).
* Fix for possible overflow in get_tick_count() (Bob Moore).
* Introduction of acpi_unload_table() (Bob Moore).
* Debugger and utilities updates (Erik Schmauss).
* Fix for unloading tables loaded via configfs (Nikolaus Voss).
- Add support for EFI specific purpose memory to optionally allow
either application-exclusive or core-kernel-mm managed access to
differentiated memory (Dan Williams).
- Fix and clean up processing of the HMAT table (Brice Goglin,
Qian Cai, Tao Xu).
- Update the ACPI EC driver to make it work on systems with
hardware-reduced ACPI (Daniel Drake).
- Always build in support for the Generic Event Device (GED) to
allow one kernel binary to work both on systems with full
hardware ACPI and hardware-reduced ACPI (Arjan van de Ven).
- Fix the table unload mechanism to unregister platform devices
created when the given table was loaded (Andy Shevchenko).
- Rework the lid blacklist handling in the button driver and add
more lid quirks to it (Hans de Goede).
- Improve ACPI-based device enumeration for some platforms based
on Intel BayTrail SoCs (Hans de Goede).
- Add an OpRegion driver for the Cherry Trail Crystal Cove PMIC
and prevent handlers from being registered for unhandled PMIC
OpRegions (Hans de Goede).
- Unify ACPI _HID/_UID matching (Andy Shevchenko).
- Clean up documentation and comments (Cao jin, James Pack, Kacper
Piwiński).
-----BEGIN PGP SIGNATURE-----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=7Cqr
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These update the ACPICA code in the kernel to upstream revision
20191018, add support for EFI specific purpose memory, update the ACPI
EC driver to make it work on systems with hardware-reduced ACPI,
improve ACPI-based device enumeration for some platforms, rework the
lid blacklist handling in the button driver and add more lid quirks to
it, unify ACPI _HID/_UID matching, fix assorted issues and clean up
the code and documentation.
Specifics:
- Update the ACPICA code in the kernel to upstream revision 20191018
including:
* Fixes for Clang warnings (Bob Moore)
* Fix for possible overflow in get_tick_count() (Bob Moore)
* Introduction of acpi_unload_table() (Bob Moore)
* Debugger and utilities updates (Erik Schmauss)
* Fix for unloading tables loaded via configfs (Nikolaus Voss)
- Add support for EFI specific purpose memory to optionally allow
either application-exclusive or core-kernel-mm managed access to
differentiated memory (Dan Williams)
- Fix and clean up processing of the HMAT table (Brice Goglin, Qian
Cai, Tao Xu)
- Update the ACPI EC driver to make it work on systems with
hardware-reduced ACPI (Daniel Drake)
- Always build in support for the Generic Event Device (GED) to allow
one kernel binary to work both on systems with full hardware ACPI
and hardware-reduced ACPI (Arjan van de Ven)
- Fix the table unload mechanism to unregister platform devices
created when the given table was loaded (Andy Shevchenko)
- Rework the lid blacklist handling in the button driver and add more
lid quirks to it (Hans de Goede)
- Improve ACPI-based device enumeration for some platforms based on
Intel BayTrail SoCs (Hans de Goede)
- Add an OpRegion driver for the Cherry Trail Crystal Cove PMIC and
prevent handlers from being registered for unhandled PMIC OpRegions
(Hans de Goede)
- Unify ACPI _HID/_UID matching (Andy Shevchenko)
- Clean up documentation and comments (Cao jin, James Pack, Kacper
Piwiński)"
* tag 'acpi-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (52 commits)
ACPI: OSI: Shoot duplicate word
ACPI: HMAT: use %u instead of %d to print u32 values
ACPI: NUMA: HMAT: fix a section mismatch
ACPI: HMAT: don't mix pxm and nid when setting memory target processor_pxm
ACPI: NUMA: HMAT: Register "soft reserved" memory as an "hmem" device
ACPI: NUMA: HMAT: Register HMAT at device_initcall level
device-dax: Add a driver for "hmem" devices
dax: Fix alloc_dax_region() compile warning
lib: Uplevel the pmem "region" ida to a global allocator
x86/efi: Add efi_fake_mem support for EFI_MEMORY_SP
arm/efi: EFI soft reservation to memblock
x86/efi: EFI soft reservation to E820 enumeration
efi: Common enable/disable infrastructure for EFI soft reservation
x86/efi: Push EFI_MEMMAP check into leaf routines
efi: Enumerate EFI_MEMORY_SP
ACPI: NUMA: Establish a new drivers/acpi/numa/ directory
ACPICA: Update version to 20191018
ACPICA: debugger: remove leading whitespaces when converting a string to a buffer
ACPICA: acpiexec: initialize all simple types and field units from user input
ACPICA: debugger: add field unit support for acpi_db_get_next_token
...
* pm-sleep:
PM / wakeirq: remove unnecessary parentheses
PM / core: Clean up some function headers in power.h
PM / hibernate: memory_bm_find_bit(): Tighten node optimisation
* pm-domains:
PM / Domains: Convert to dev_to_genpd_safe() in genpd_syscore_switch()
mmc: tmio: Avoid boilerplate code in ->runtime_suspend()
PM / Domains: Implement the ->start() callback for genpd
PM / Domains: Introduce dev_pm_domain_start()
* pm-opp:
PM / OPP: Support adjusting OPP voltages at runtime
* powercap:
powercap/intel_rapl: add support for Cometlake desktop
powercap/intel_rapl: add support for CometLake Mobile
This reverts commit 7a7dab2370. We found
out that there is still a race with RuntimePM. This can lead to a hang
when accessing the eMMC in some situations. Revert this change until the
RPM issue is fixed.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Apart from taps set by auto tuning, ZynqMP platform has feature to set
the tap values manually. Add support to set tap delay values in HW via
ZynqMP SoC framework.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support to read Clock Phase Delays from the DT and set it via
clk_set_phase() API from clock framework. Some of the controllers might
have their own handling of setting clock delays, for this keep the
set_clk_delays as function pointer which can be assigned controller
specific handling of the same.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are some operations like setting the clock delays may need to have
two clocks, one for output path and one for input path. Adding input
path clock for some phys to use.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To improve the code readability, use two different structs, one for
clock provider data and one for mmc platform data.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The correct form is "did not become", so fix it accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add read_l callback in sdhci_ops with flipping of SDHCI_CARD_PRESENT
bit in case of inverted card detection signal.
Signed-off-by: Ivan Mikhaylov <i.mikhaylov@yadro.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable CONFIG_MMC_SDHCI_IO_ACCESSORS for the ASPEED MMC driver. The read_l
callback is used for inverted card detection.
Signed-off-by: Ivan Mikhaylov <i.mikhaylov@yadro.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add Support for CQHCI (Command Queuing Host Controller Interface)
for each of the host controllers present in TI's J721E devices.
Add cqhci_ops and a .irq() callback to handle cqhci specific interrupts.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With large eMMC cards, it is possible to create general purpose
partitions that are bigger than 4GB. The size member of the mmc_part
struct is only an unsigned int which overflows for gp partitions larger
than 4GB. Change this to a u64 to handle the overflow.
Signed-off-by: Bradley Bolen <bradleybolen@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Isolated initially to renesas_sdhi_internal_dmac [1], Ulf suggested
adding MMC_CAP_ERASE to the TMIO mmc core:
On Fri, Nov 15, 2019 at 10:27:25AM +0100, Ulf Hansson wrote:
-- snip --
This test and due to the discussions with Wolfram and you in this
thread, I would actually suggest that you enable MMC_CAP_ERASE for all
tmio variants, rather than just for this particular one.
In other words, set the cap in tmio_mmc_host_probe() should be fine,
as it seems none of the tmio variants supports HW busy detection at
this point.
-- snip --
Testing on R-Car H3ULCB-KF doesn't reveal any issues (v5.4-rc7):
root@rcar-gen3:~# lsblk
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
mmcblk0 179:0 0 59.2G 0 disk <--- eMMC
mmcblk0boot0 179:8 0 4M 1 disk
mmcblk0boot1 179:16 0 4M 1 disk
mmcblk1 179:24 0 30G 0 disk <--- SD card
root@rcar-gen3:~# time blkdiscard /dev/mmcblk0
real 0m8.659s
user 0m0.001s
sys 0m1.920s
root@rcar-gen3:~# time blkdiscard /dev/mmcblk1
real 0m1.176s
user 0m0.001s
sys 0m0.124s
[1] https://lore.kernel.org/linux-renesas-soc/20191112134808.23546-1-erosca@de.adit-jv.com/
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Originally-by: Harish Jenny K N <harish_kandiga@mentor.com>
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
wl1251 and wl1271 have different vendor id and device id.
So we need to handle both with sdio quirks.
Fixes: 884f386078 ("mmc: core: move some sdio IDs out of quirks file")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now as we have removed the last user (pandora_wl1251_init_card)
of this callback, we can remove it from the hsmmc code.
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pandora_wl1251_init_card was used to do special pdata based
setup of the sdio mmc interface. This does no longer work with
v4.7 and later. A fix requires a device tree based mmc3 setup.
Therefore we move the special setup to omap_hsmmc.c instead
of calling some pdata supplied init_card function.
The new code checks for a DT child node compatible to wl1251
so it will not affect other MMC3 use cases.
Generally, this code was and still is a hack and should be
moved to mmc core to e.g. read such properties from optional
DT child nodes.
Fixes: 81eef6ca92 ("mmc: omap_hsmmc: Use dma_request_chan() for requesting DMA channel")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: <stable@vger.kernel.org> # v4.7+
[Ulf: Fixed up some checkpatch complaints]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to the comment, board files used to specify 1 ms for the
debounce time. gpiod_set_debounce() needs the debounce time to be
specified in units of microseconds, so make sure to multiply the value
by 1000.
Note that, according to the git log, the board files actually did
specify 1 us for bounce times, but that seems really low. Device tree
bindings for this type of GPIO typically specify the debounce times in
milliseconds, so setting this default value to 1 ms seems like it would
be somewhat safer.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It have turned out that it's not a good idea to unconditionally do a power
cycle and then to re-initialize the SDIO card, as currently done through
mmc_hw_reset() -> mmc_sdio_hw_reset(). This because there may be multiple
SDIO func drivers probed, who also shares the same SDIO card.
To address these scenarios, one may be tempted to use a notification
mechanism, as to allow the core to inform each of the probed func drivers,
about an ongoing HW reset. However, supporting such an operation from the
func driver point of view, may not be entirely trivial.
Therefore, let's use a more simplistic approach to solve the problem, by
instead forcing the card to be removed and re-detected, via scheduling a
rescan-work. In this way, we can rely on existing infrastructure, as the
func driver's ->remove() and ->probe() callbacks, becomes invoked to deal
with the cleanup and the re-initialization.
This solution may be considered as rather heavy, especially if a func
driver doesn't share its card with other func drivers. To address this,
let's keep the current immediate HW reset option as well, but run it only
when there is one func driver probed for the card.
Finally, to allow the caller of mmc_hw_reset(), to understand if the reset
is being asynchronously managed from a scheduled work, it returns 1
(propagated from mmc_sdio_hw_reset()). If the HW reset is executed
successfully and synchronously it returns 0, which maintains the existing
behaviour.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Upfront in mmc_rescan() we use the host->rescan_entered flag, to allow
scanning only once for non-removable cards. Therefore, it's also not
possible that we can have a corresponding card bus attached (host->bus_ops
is NULL), when we are scanning non-removable cards.
For this reason, let' drop the check for mmc_card_is_removable() as it's
redundant.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The quirks2 are parsed and set (e.g. from DT) before the quirk for broken
HS200 is set in the driver.
The driver needs to enable just this flag, not rewrite the whole quirk set.
Fixes: 7871aa60ae ("mmc: sdhci-of-at91: add quirk for broken HS200")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The ->init_card() host ops is printing message to the log, without actually
doing something useful. Let's just drop this code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds SDHI support for RZ/G2N (R8A774B1) SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC IOCTLS with R1B responses may cause the card to enter the busy state,
which means it's not ready to receive a new request. To prevent new
requests from being sent to the card, use a CMD13 polling loop to verify
that the card returns to the transfer state, before completing the request.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To prepare for more users of card_busy_detect(), let's drop the struct
request * as an in-parameter and convert to log the error message via
dev_err() instead of pr_err().
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A previous patch implemented an incomplete workaround of erratum
A-008171. The complete workaround is as below. This patch is to
implement the complete workaround which uses SW tuning if HW tuning
fails, and retries both HW/SW tuning once with reduced clock if
workaround fails. This is suggested by hardware team, and the patch
had been verified on LS1046A eSDHC + Phison 32G eMMC which could
trigger the erratum.
Workaround:
/* For T1040, T2080, LS1021A, T1023 Rev 1: */
1. Program TBPTR[TB_WNDW_END_PTR] = 3*DIV_RATIO.
2. Program TBPTR[TB_WNDW_START_PTR] = 5*DIV_RATIO.
3. Program the software tuning mode by setting TBCTL[TB_MODE] = 2'h3.
4. Set SYSCTL2[EXTN] and SYSCTL2[SAMPCLKSEL].
5. Issue SEND_TUNING_BLK Command (CMD19 for SD, CMD21 for MMC).
6. Wait for IRQSTAT[BRR], buffer read ready, to be set.
7. Clear IRQSTAT[BRR].
8. Check SYSCTL2[EXTN] to be cleared.
9. Check SYSCTL2[SAMPCLKSEL], Sampling Clock Select. It's set value
indicate tuning procedure success, and clear indicate failure.
In case of tuning failure, fixed sampling scheme could be used by
clearing TBCTL[TB_EN].
/* For LS1080A Rev 1, LS2088A Rev 1.0, LA1575A Rev 1.0: */
1. Read the TBCTL[31:0] register. Write TBCTL[11:8]=4'h8 and wait for
1ms.
2. Read the TBCTL[31:0] register and rewrite again. Wait for 1ms second.
3. Read the TBSTAT[31:0] register twice.
3.1 Reset data lines by setting ESDHCCTL[RSTD] bit.
3.2 Check ESDHCCTL[RSTD] bit.
3.3 If ESDHCCTL[RSTD] is 0, go to step 3.4 else go to step 3.2.
3.4 Write 32'hFFFF_FFFF to IRQSTAT register.
4. if TBSTAT[15:8]-TBSTAT[7:0] > 4*DIV_RATIO or TBSTAT[7:0]-TBSTAT[15:8]
> 4*DIV_RATIO , then program TBPTR[TB_WNDW_END_PTR] = 4*DIV_RATIO and
program TBPTR[TB_WNDW_START_PTR] = 8*DIV_RATIO.
/* For LS1012A Rev1, LS1043A Rev 1.x, LS1046A 1.0: */
1. Read the TBCTL[0:31] register. Write TBCTL[20:23]=4'h8 and wait for
1ms.
2. Read the TBCTL[0:31] register and rewrite again. Wait for 1ms second.
3. Read the TBSTAT[0:31] register twice.
3.1 Reset data lines by setting ESDHCCTL[RSTD] bit.
3.2 Check ESDHCCTL[RSTD] bit.
3.3 If ESDHCCTL[RSTD] is 0, go to step 3.4 else go to step 3.2.
3.4 Write 32'hFFFF_FFFF to IRQSTAT register.
4. if TBSTAT[16:23]-TBSTAT[24:31] > 4*DIV_RATIO or TBSTAT[24:31]-
TBSTAT[16:23] > 4* DIV_RATIO , then program TBPTR[TB_WNDW_END_PTR] =
4*DIV_RATIO and program TBPTR[TB_WNDW_START_PTR] = 8*DIV_RATIO.
/* For LS1080A Rev 1, LS2088A Rev 1.0, LA1575A Rev 1.0 LS1012A Rev1,
* LS1043A Rev 1.x, LS1046A 1.0:
*/
5. else program TBPTR[TB_WNDW_END_PTR] = 3*DIV_RATIO and program
TBPTR[TB_WNDW_START_PTR] = 5*DIV_RATIO.
6. Program the software tuning mode by setting TBCTL[TB_MODE] = 2'h3.
7. Set SYSCTL2[EXTN], wait 1us and SYSCTL2[SAMPCLKSEL].
8. Issue SEND_TUNING_BLK Command (CMD19 for SD, CMD21 for MMC).
9. Wait for IRQSTAT[BRR], buffer read ready, to be set.
10. Clear IRQSTAT[BRR].
11. Check SYSCTL2[EXTN] to be cleared.
12. Check SYSCTL2[SAMPCLKSEL], Sampling Clock Select. It's set value
indicate tuning procedure success, and clear indicate failure.
In case of tuning failure, fixed sampling scheme could be used by
clearing TBCTL[TB_EN].
Fixes: b1f378ab53 ("mmc: sdhci-of-esdhc: add erratum A008171 support")
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The ESDHC_FLUSH_ASYNC_FIFO bit which is set to flush asynchronous FIFO
should be polled until it's auto cleared by hardware.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a property to keep the analog calibration cell powered.
This feature is specific to the Microchip SDHCI IP and outside
of the standard SDHCI register map.
By always keeping it on, after a full reset sequence, we make sure
that this feature is activated and not disabled.
We expose a hardware property to the DT as this feature can be used
to adapt SDHCI behavior vs. how the SDCAL SoC pin is connected
on the board.
Note that managing properly this property would reduce
power consumption on some SAMA5D2 SiP revisions.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make sdmmc_idma_validate_data to avoid the following warning
from sparse:
drivers/mmc/host/mmci_stm32_sdmmc.c:28:5: warning: symbol 'sdmmc_idma_validate_data' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for low power mode to the Ingenic's MMC/SD Controller.
Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for probing mmc driver on the X1000 Soc from Ingenic.
Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for probing mmc driver on the JZ4760 Soc from Ingenic.
Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix sparse warnings:
drivers/mmc/host/sdhci-pci-core.c:1599:6: warning: symbol 'amd_sdhci_reset' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The current arasan sdhci PHY configuration isn't compatible
with the PHY on Intel's LGM(Lightning Mountain) SoC devices.
Therefore, add a new compatible, to adapt the Intel's LGM
SDXC PHY with arasan-sdhc controller to configure the PHY.
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a specific busy_complete callback for sdmmc variant.
sdmmc has 2 status flags:
-busyd0: This is a hardware status flag (inverted value of d0 line).
it does not generate an interrupt.
-busyd0end: This indicates only end of busy following a CMD response.
On busy to Not busy changes, an interrupt is generated (if unmask)
and BUSYD0END status flag is set. Status flag is cleared by writing
corresponding interrupt clear bit in MMCICLEAR.
The legacy busy completion has no dedicated interrupt for the end
of busy, so it's must monitor step by step the busy progression.
On sdmmc variant, this procedure is not needed, it's just need
to wait the busyd0end interrupt.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds busy_completion callback at mmci_host_ops
to allow to define a specific busy completion by variant.
The legacy code corresponding to busy completion used
by ux500 variants is moved to ux500_busy_complete function.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the stm32_sdmmc variant, the datatimer is active not only during
data transfers with the DPSM, but also while waiting for the busyend
IRQs from commands having the MMC_RSP_BUSY flag set. This leads to an
incorrect IRQ being raised to signal MCI_DATATIMEOUT error, which
simply breaks the behaviour.
Address this by updating the datatimer value before sending a command
having the MMC_RSP_BUSY flag set. To inform the mmc core about the
maximum supported busy timeout, which also depends on the current
clock rate, set ->max_busy_timeout (in ms).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix the following sparse warnings by making any functions not used
outsde the mmci.c driver static.
drivers/mmc/host/mmci.c:422:6: warning: symbol 'mmci_dma_release' was not declared. Should it be static?
drivers/mmc/host/mmci.c:430:6: warning: symbol 'mmci_dma_setup' was not declared. Should it be static?
drivers/mmc/host/mmci.c:465:5: warning: symbol 'mmci_prep_data' was not declared. Should it be static?
drivers/mmc/host/mmci.c:481:6: warning: symbol 'mmci_unprep_data' was not declared. Should it be static?
drivers/mmc/host/mmci.c:490:6: warning: symbol 'mmci_get_next_data' was not declared. Should it be static?
drivers/mmc/host/mmci.c:498:5: warning: symbol 'mmci_dma_start' was not declared. Should it be static?
drivers/mmc/host/mmci.c:533:6: warning: symbol 'mmci_dma_finalize' was not declared. Should it be static?
drivers/mmc/host/mmci.c:542:6: warning: symbol 'mmci_dma_error' was not declared. Should it be static?
drivers/mmc/host/mmci.c:951:6: warning: symbol 'mmci_variant_init' was not declared. Should it be static?
drivers/mmc/host/mmci.c:956:6: warning: symbol 'ux500v2_variant_init' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are a couple of statements that are indented by an extra
space, clean this up by remove the extraneous spaces.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Simplify this function implementation by using a known wrapper function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use devm_platform_ioremap_resource helper which wraps
platform_get_resource() and devm_ioremap_resource() together.
Generated by: scripts/coccinelle/api/devm_platform_ioremap_resource.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Saiyam Doshi <saiyamdoshi.in@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
PM has been reworked, so eMMC gets now detected on R-Car H3 ES1.0 and
2.0 as well as M3-N without the workaround. Card detect and write
protect also still work. Remove the workaround.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add SD/MMC driver for Actions Semi Owl SoCs. This driver currently
supports standard, high speed, SDR12, SDR25 and SDR50. DDR50 mode is
supported but it is untested. There is no SDIO support for now.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SD Host controller on Milbeaut consists of two controller parts.
One is core controller F_SDH30, this is similar to sdhci-fujitsu
controller.
Another is bridge controller.
This bridge controller is not compatible with sdhci-fujitsu controller.
This is special for Milbeaut series. This has some functions.
For example, reset control, clock enable/select for SDR50/25/12, set
property of SD physical pins, retuning control, set capabilityies.
This bridge controller requires special procedures at reset or clock
enablement or change for further tuning of clock.
Signed-off-by: Takao Orito <orito.takao@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
AMD SDHC 0x7906 requires a hard reset to clear all internal state.
Otherwise it can get into a bad state where the DATA lines are always
read as zeros.
This change requires firmware that can transition the device into
D3Cold for it to work correctly. If the firmware does not support
transitioning to D3Cold then the power state transitions are a no-op.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In sdhci_do_reset we call the reset callback which is typically
sdhci_reset. sdhci_reset can wait for up to 100ms waiting for the
controller to reset. If SDHCI_RESET_ALL was passed as the flag, the
controller will clear the IRQ mask. If during that 100ms the card is
removed there is no notification to the MMC system that the card was
removed. So from the drivers point of view the card is always present.
By making sdhci_reinit compare the present state it can schedule a
rescan if the card was removed while a reset was in progress.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rather than checking the 'runtime_synced' flag each time the
->runtime_suspend() callback is invoked, let's convert into using
dev_pm_domain_start() during ->probe() and drop the corresponding
boilerplate code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
"dw_mci.state" is an enum, which is compatible with u32, so there is no
need to cast its address, preventing further compiler checks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20191025094130.26033-8-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"dw_mci.pending_events" and "dw_mci.completed_events" are "unsigned
long", i.e. 32-bit or 64-bit, depending on the platform. Hence casting
their addresses to "u32 *", and calling debugfs_create_x32() breaks
operation on 64-bit platforms.
Fix this by using the new debugfs_create_xul() helper instead.
Fixes: f95f3850f7 ("mmc: dw_mmc: Add Synopsys DesignWare mmc host driver.")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20191025094130.26033-7-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"atmel_mci.state" is an enum, which is compatible with u32, so there is
no need to cast its address, preventing further compiler checks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20191025094130.26033-6-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"atmel_mci.pending_events" and "atmel_mci.completed_events" are
"unsigned long", i.e. 32-bit or 64-bit, depending on the platform.
Hence casting their addresses to "u32 *", and calling
debugfs_create_x32() breaks operation on 64-bit platforms.
Fix this by using the new debugfs_create_xul() helper instead.
Fixes: deec9ae31e ("atmel-mci: debugfs support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20191025094130.26033-5-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since ceeeb99cd8 we no longer abuse the DMA_CTRL_ACK flag for custom
driver use and introduced the MXS_DMA_CTRL_WAIT4END instead. We have not
changed all users to this flag though. This patch fixes it for the
mxs-mmc driver.
Fixes: ceeeb99cd8 ("dmaengine: mxs: rename custom flag")
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Fabio Estevam <festevam@gmail.com>
Reported-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Tested-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a write memory barrier to make sure that descriptors are actually
written to memory, before ringing the doorbell.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to the App note[1] detailing the tuning algorithm, for
temperatures < -20C, the initial tuning value should be min(largest value
in LPW - 24, ceil(13/16 ratio of LPW)). The largest value in LPW is
(max_window + 4 * (max_len - 1)) and not (max_window + 4 * max_len) itself.
Fix this implementation.
[1] http://www.ti.com/lit/an/spraca9b/spraca9b.pdf
Fixes: 961de0a856 ("mmc: sdhci-omap: Workaround errata regarding SDR104/HS200 tuning failures (i929)")
Cc: stable@vger.kernel.org
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since we have a generic helper, drop custom implementation in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As platform_get_irq() now prints an error when the interrupt does not
exist, a scary warning may be printed for an optional interrupt:
sh_mmcif ee200000.mmc: IRQ index 1 not found
Fix this by calling platform_get_irq_optional() instead for the second
interrupt, which is optional.
Remove the now superfluous error printing for the first interrupt, which
is mandatory.
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As platform_get_irq() now prints an error when the interrupt does not
exist, counting interrupts by looping until failure causes the printing
of scary messages like:
renesas_sdhi_internal_dmac ee140000.sd: IRQ index 1 not found
Fix this by using the platform_irq_count() helper to avoid touching
non-existent interrupts.
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for the GL9750 and GL9755 chipsets.
Enable v4 mode and wait 5ms after set 1.8V signal enable for GL9750/
GL9755. Fix the value of SDHCI_MAX_CURRENT register and use the vendor
tuning flow for GL9750.
Co-developed-by: Michael K Johnson <johnsonm@danlj.org>
Signed-off-by: Michael K Johnson <johnsonm@danlj.org>
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI controller on Tegra186 supports 40-bit addressing, which is
usually enough to address all of system memory. However, if the SDHCI
controller is behind an IOMMU, the address space can go beyond. This
happens on Tegra186 and later where the ARM SMMU has an input address
space of 48 bits. If the DMA API is backed by this ARM SMMU, the top-
down IOVA allocator will cause IOV addresses to be returned that the
SDHCI controller cannot access.
Unfortunately, prior to the introduction of the ->set_dma_mask() host
operation, the SDHCI core would set either a 64-bit DMA mask if the
controller claimed to support 64-bit addressing, or a 32-bit DMA mask
otherwise.
Since the full 64 bits cannot be addressed on Tegra, this had to be
worked around in commit 68481a7e1c ("mmc: tegra: Mark 64 bit dma
broken on Tegra186") by setting the SDHCI_QUIRK2_BROKEN_64_BIT_DMA
quirk, which effectively restricts the DMA mask to 32 bits.
One disadvantage of this is that dma_map_*() APIs will now try to use
the swiotlb to bounce DMA to addresses beyond of the controller's DMA
mask. This in turn caused degraded performance and can lead to
situations where the swiotlb buffer is exhausted, which in turn leads
to DMA transfers to fail.
With the recent introduction of the ->set_dma_mask() host operation,
this can now be properly fixed. For each generation of Tegra, the exact
supported DMA mask can be configured. This kills two birds with one
stone: it avoids the use of bounce buffers because system memory never
exceeds the addressable memory range of the SDHCI controllers on these
devices, and at the same time when an IOMMU is involved, it prevents
IOV addresses from being allocated beyond the addressible range of the
controllers.
Since the DMA mask is now properly handled, the 64-bit DMA quirk can be
removed.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
[treding@nvidia.com: provide more background in commit message]
Tested-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Cc: stable@vger.kernel.org # v4.15 +
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We must not unconditionally set the DMA snoop bit; if the DMA API is
assuming that the device is not DMA coherent, and the device snoops the
CPU caches, the device can see stale cache lines brought in by
speculative prefetch.
This leads to the device seeing stale data, potentially resulting in
corrupted data transfers. Commonly, this results in a descriptor fetch
error such as:
mmc0: ADMA error
mmc0: sdhci: ============ SDHCI REGISTER DUMP ===========
mmc0: sdhci: Sys addr: 0x00000000 | Version: 0x00002202
mmc0: sdhci: Blk size: 0x00000008 | Blk cnt: 0x00000001
mmc0: sdhci: Argument: 0x00000000 | Trn mode: 0x00000013
mmc0: sdhci: Present: 0x01f50008 | Host ctl: 0x00000038
mmc0: sdhci: Power: 0x00000003 | Blk gap: 0x00000000
mmc0: sdhci: Wake-up: 0x00000000 | Clock: 0x000040d8
mmc0: sdhci: Timeout: 0x00000003 | Int stat: 0x00000001
mmc0: sdhci: Int enab: 0x037f108f | Sig enab: 0x037f108b
mmc0: sdhci: ACmd stat: 0x00000000 | Slot int: 0x00002202
mmc0: sdhci: Caps: 0x35fa0000 | Caps_1: 0x0000af00
mmc0: sdhci: Cmd: 0x0000333a | Max curr: 0x00000000
mmc0: sdhci: Resp[0]: 0x00000920 | Resp[1]: 0x001d8a33
mmc0: sdhci: Resp[2]: 0x325b5900 | Resp[3]: 0x3f400e00
mmc0: sdhci: Host ctl2: 0x00000000
mmc0: sdhci: ADMA Err: 0x00000009 | ADMA Ptr: 0x000000236d43820c
mmc0: sdhci: ============================================
mmc0: error -5 whilst initialising SD card
but can lead to other errors, and potentially direct the SDHCI
controller to read/write data to other memory locations (e.g. if a valid
descriptor is visible to the device in a stale cache line.)
Fix this by ensuring that the DMA snoop bit corresponds with the
behaviour of the DMA API. Since the driver currently only supports DT,
use of_dma_is_coherent(). Note that device_get_dma_attr() can not be
used as that risks re-introducing this bug if/when the driver is
converted to ACPI.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
ADMA errors are potentially data corrupting events; although we print
the register state, we do not usefully print the ADMA descriptors.
Worse than that, we print them by referencing their virtual address
which is meaningless when the register state gives us the DMA address
of the failing descriptor.
Print the ADMA descriptors giving their DMA addresses rather than their
virtual addresses, and print them using SDHCI_DUMP() rather than DBG().
We also do not show the correct value of the interrupt status register;
the register dump shows the current value, after we have cleared the
pending interrupts we are going to service. What is more useful is to
print the interrupts that _were_ pending at the time the ADMA error was
encountered. Fix that too.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- add dma-mapping and block layer helpers to take care of IOMMU
merging for mmc plus subsequent fixups (Yoshihiro Shimoda)
- rework handling of the pgprot bits for remapping (me)
- take care of the dma direct infrastructure for swiotlb-xen (me)
- improve the dma noncoherent remapping infrastructure (me)
- better defaults for ->mmap, ->get_sgtable and ->get_required_mask (me)
- cleanup mmaping of coherent DMA allocations (me)
- various misc cleanups (Andy Shevchenko, me)
-----BEGIN PGP SIGNATURE-----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=/wGv
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.4' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- add dma-mapping and block layer helpers to take care of IOMMU merging
for mmc plus subsequent fixups (Yoshihiro Shimoda)
- rework handling of the pgprot bits for remapping (me)
- take care of the dma direct infrastructure for swiotlb-xen (me)
- improve the dma noncoherent remapping infrastructure (me)
- better defaults for ->mmap, ->get_sgtable and ->get_required_mask
(me)
- cleanup mmaping of coherent DMA allocations (me)
- various misc cleanups (Andy Shevchenko, me)
* tag 'dma-mapping-5.4' of git://git.infradead.org/users/hch/dma-mapping: (41 commits)
mmc: renesas_sdhi_internal_dmac: Add MMC_CAP2_MERGE_CAPABLE
mmc: queue: Fix bigger segments usage
arm64: use asm-generic/dma-mapping.h
swiotlb-xen: merge xen_unmap_single into xen_swiotlb_unmap_page
swiotlb-xen: simplify cache maintainance
swiotlb-xen: use the same foreign page check everywhere
swiotlb-xen: remove xen_swiotlb_dma_mmap and xen_swiotlb_dma_get_sgtable
xen: remove the exports for xen_{create,destroy}_contiguous_region
xen/arm: remove xen_dma_ops
xen/arm: simplify dma_cache_maint
xen/arm: use dev_is_dma_coherent
xen/arm: consolidate page-coherent.h
xen/arm: use dma-noncoherent.h calls for xen-swiotlb cache maintainance
arm: remove wrappers for the generic dma remap helpers
dma-mapping: introduce a dma_common_find_pages helper
dma-mapping: always use VM_DMA_COHERENT for generic DMA remap
vmalloc: lift the arm flag for coherent mappings to common code
dma-mapping: provide a better default ->get_required_mask
dma-mapping: remove the dma_declare_coherent_memory export
remoteproc: don't allow modular build
...
Accessing the device when it may be runtime suspended is a bug, which is
the case in tmio_mmc_host_remove(). Let's fix the behaviour.
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
The tmio_mmc_host_probe() calls pm_runtime_set_active() to update the
runtime PM status of the device, as to make it reflect the current status
of the HW. This works fine for most cases, but unfortunate not for all.
Especially, there is a generic problem when the device has a genpd attached
and that genpd have the ->start|stop() callbacks assigned.
More precisely, if the driver calls pm_runtime_set_active() during
->probe(), genpd does not get to invoke the ->start() callback for it,
which means the HW isn't really fully powered on. Furthermore, in the next
phase, when the device becomes runtime suspended, genpd will invoke the
->stop() callback for it, potentially leading to usage count imbalance
problems, depending on what's implemented behind the callbacks of course.
To fix this problem, convert to call pm_runtime_get_sync() from
tmio_mmc_host_probe() rather than pm_runtime_set_active(). Additionally, to
avoid bumping usage counters and unnecessary re-initializing the HW the
first time the tmio driver's ->runtime_resume() callback is called,
introduce a state flag to keeping track of this.
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
This reverts commit 7ff2131933.
It turns out that the above commit introduces other problems. For example,
calling pm_runtime_set_active() must not be done prior calling
pm_runtime_enable() as that makes it fail. This leads to additional
problems, such as clock enables being wrongly balanced.
Rather than fixing the problem on top, let's start over by doing a revert.
Fixes: 7ff2131933 ("mmc: tmio: move runtime PM enablement to the driver implementations")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Since this host controller can merge bigger segments if DMA API
layer cam merge the segments, this patch adds the flag.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The commit 38c38cb732 ("mmc: queue: use bigger segments if DMA MAP
layer can merge the segments") always enables the bugger segments
if DMA MAP layer can merge the segments, but some controllers (SDHCI)
have strictly limitation about the segments size, and then the commit
breaks on the controllers.
To fix the issue, this patch adds a new flag MMC_CAP2_MERGE_CAPABLE
into the struct mmc_host and the bigger segments usage is disabled
as default.
Reported-by: Thierry Reding <treding@nvidia.com>
Fixes: 38c38cb732 ("mmc: queue: use bigger segments if DMA MAP layer can merge the segments")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Don't populate the array degrees on the stack but instead make it
static const. Makes the object code smaller by 46 bytes.
Before:
text data bss dec hex filename
5356 1560 0 6916 1b04 dw_mmc-hi3798cv200.o
After:
text data bss dec hex filename
5214 1656 0 6870 1ad6 dw_mmc-hi3798cv200.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of keeping track of whether SDIO IRQs have been enabled via an
internal sdhci status flag, avoid the open-coding and convert into using
sdio_irq_claimed().
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Nowadays sdhci prevents runtime suspend when SDIO IRQs are enabled.
However, some variants such as sdhci-esdhc-imx's, tries to allow runtime
suspend while having the SDIO IRQs enabled, but without supporting remote
wakeups. This support is a bit questionable, especially if the host device
have a PM domain attached that can be power gated, but more importantly,
the code have also become redundant (which was not the case when it was
introduced).
Rather than keeping the redundant code around, let's drop it and leave this
to be revisited later on.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci_ack_sdio_irq() is called only when SDIO IRQs are enabled.
Therefore, let's drop the redundant check of the internal
SDHCI_SDIO_IRQ_ENABLED flag and just re-enable the IRQs immediately.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
System suspend/resume of SDIO cards, with SDIO IRQs enabled and when using
MMC_CAP2_SDIO_IRQ_NOTHREAD is unfortunate still suffering from a fragile
behaviour. Some problems have been taken care of so far, but more issues
remains.
For example, calling the ->ack_sdio_irq() callback to let host drivers
re-enable the SDIO IRQs is a bad idea, unless the IRQ have been consumed,
which may not be the case during system suspend/resume. This may lead to
that a host driver re-signals the same SDIO IRQ over and over again,
causing a storm of IRQs and gives a ping-pong effect towards the
sdio_irq_work().
Moreover, calling the ->enable_sdio_irq() callback at system resume to
re-enable already enabled SDIO IRQs for the host, causes the runtime PM
count for some host drivers to become in-balanced. This then leads to the
host to remain runtime resumed, no matter if it's needed or not.
To fix these problems, let's check if process_sdio_pending_irqs() actually
consumed the SDIO IRQ, before we continue to ack the IRQ by invoking the
->ack_sdio_irq() callback.
Additionally, there should be no need to re-enable SDIO IRQs as the host
driver already knows if they were enabled at system suspend, thus also
whether it needs to re-enable them at system resume. For this reason, drop
the call to ->enable_sdio_irq() during system resume.
In regards to these changes there is yet another issue, which is when there
is an SDIO IRQ being signaled by the host driver, but after the SDIO card
has been system suspended. Currently these IRQs are just thrown away, while
we should at least make sure to try to consume them when the SDIO card has
been system resumed. Fix this by queueing a sdio_irq_work() after we system
resumed the SDIO card.
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To make sure SDIO func drivers behaves correctly during system
suspend/resume, let add a WARN_ON in case the condition is a non-powered
SDIO card and there are some SDIO IRQs still being claimed.
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For the MMC_CAP2_SDIO_IRQ_NOTHREAD case and when using sdio_signal_irq(),
the ->ack_sdio_irq() is already mandatory, which was not the case for those
host drivers that called sdio_run_irqs() directly.
As there are no longer any drivers calling sdio_run_irqs(), let's clarify
the code by dropping the unnecessary check and explicitly state that the
callback is mandatory in the header file.
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdio_irq_pending flag is used to let host drivers indicate that it has
signaled an IRQ. If that is the case and we only have a single SDIO func
that have claimed an SDIO IRQ, our assumption is that we can avoid reading
the SDIO_CCCR_INTx register and just call the SDIO func irq handler
immediately. This makes sense, but the flag is set/cleared in a somewhat
messy order, let's fix that up according to below.
First, the flag is currently set in sdio_run_irqs(), which is executed as a
work that was scheduled from sdio_signal_irq(). To make it more implicit
that the host have signaled an IRQ, let's instead immediately set the flag
in sdio_signal_irq(). This also makes the behavior consistent with host
drivers that uses the legacy, mmc_signal_sdio_irq() API. This have no
functional impact, because we don't expect host drivers to call
sdio_signal_irq() until after the work (sdio_run_irqs()) have been executed
anyways.
Second, currently we never clears the flag when using the sdio_run_irqs()
work, but only when using the sdio_irq_thread(). Let make the behavior
consistent, by moving the flag to be cleared inside the common
process_sdio_pending_irqs() function. Additionally, tweak the behavior of
the flag slightly, by avoiding to clear it unless we processed the SDIO
IRQ. The purpose with this at this point, is to keep the information about
whether there have been an SDIO IRQ signaled by the host, so at system
resume we can decide to process it without reading the SDIO_CCCR_INTx
register.
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To improve code quality, let's move the code that gets pending SDIO IRQs
from process_sdio_pending_irqs() into a dedicated function.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
[Ulf: Converted function into static]
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In cases when SDIO IRQs have been enabled, runtime suspend is prevented by
the driver. However, this still means msdc_runtime_suspend|resume() gets
called during system suspend/resume, via pm_runtime_force_suspend|resume().
This means during system suspend/resume, the register context of the mtk-sd
device most likely loses its register context, even in cases when SDIO IRQs
have been enabled.
To re-enable the SDIO IRQs during system resume, the mtk-sd driver
currently relies on the mmc core to re-enable the SDIO IRQs when it resumes
the SDIO card, but this isn't the recommended solution. Instead, it's
better to deal with this locally in the mtk-sd driver, so let's do that.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In cases when SDIO IRQs have been enabled, runtime suspend is prevented by
the driver. However, this still means dw_mci_runtime_suspend|resume() gets
called during system suspend/resume, via pm_runtime_force_suspend|resume().
This means during system suspend/resume, the register context of the dw_mmc
device most likely loses its register context, even in cases when SDIO IRQs
have been enabled.
To re-enable the SDIO IRQs during system resume, the dw_mmc driver
currently relies on the mmc core to re-enable the SDIO IRQs when it resumes
the SDIO card, but this isn't the recommended solution. Instead, it's
better to deal with this locally in the dw_mmc driver, so let's do that.
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix data read/write error in HS200 mode due to chip DLL lock phase shift
Signed-off-by: Shirley Her <shirley.her@bayhubtech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Change O2 Host PLL and DLL register name
Signed-off-by: Shirley Her <shirley.her@bayhubtech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When switching from any MMC speed mode that requires 1.8v
(HS200, HS400 and HS400ES) to High Speed (HS) mode, the system
ends up configured for SDR12 with a 50MHz clock which is an illegal
mode.
This happens because the SDHCI_CTRL_VDD_180 bit in the
SDHCI_HOST_CONTROL2 register is left set and when this bit is
set, the speed mode is controlled by the SDHCI_CTRL_UHS field
in the SDHCI_HOST_CONTROL2 register. The SDHCI_CTRL_UHS field
will end up being set to 0 (SDR12) by sdhci_set_uhs_signaling()
because there is no UHS mode being set.
The fix is to change sdhci_set_uhs_signaling() to set the
SDHCI_CTRL_UHS field to SDR25 (which is the same as HS) for
any switch to HS mode.
This was found on a new eMMC controller that does strict checking
of the speed mode and the corresponding clock rate. It caused the
switch to HS400 mode to fail because part of the sequence to switch
to HS400 requires a switch from HS200 to HS before going to HS400.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Resolves the following build error reported by the 0-day bot:
ERROR: "of_platform_device_create" [drivers/mmc/host/sdhci-of-aspeed.ko] undefined!
SPARC does not set CONFIG_OF_ADDRESS so the symbol is missing. Depend on
CONFIG_OF_ADDRESS to ensure the driver is only built for supported
configurations.
Fixes: 2d28dbe042f4 ("mmc: sdhci-of-aspeed: Add support for the ASPEED SD controller")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a get_max_clock() handler to sdhci-of-aspeed to report f_max as the
maximum clock rate if it is set. This enables artificial limitation of
the bus speed via max-frequency in the devicetree for e.g. the AST2600
evaluation board where I was seeing errors at 200MHz.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The early-exit didn't seem to matter on the AST2500, but on the AST2600
the SD clock genuinely may not be running on entry to
aspeed_sdhci_set_clock(). Remove the early exit to ensure we always run
sdhci_enable_clk().
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use for_each_sg() macro instead of open coded variant.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Save set clock in mmc_host actual_clock enabling exporting it via debugfs.
This will indicate the precise SD clock in I/O settings rather than only the
sometimes misleading requested clock.
Signed-off-by: Tamás Szűcs <tszucs@protonmail.ch>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, the DMA addresses are casted to (u64) for the upper 32bits
to avoid "right shift count >= width of type" warning.
<linux/kernel.h> provides macros to address this, and I like the macro
names are self-documenting.
I introduced a new helper, sdhci_set_adma_addr() to avoid the code
duplication.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The datasheet of the IP (sd4hc) says it is compiatible with SDHCI v4,
but the spec version field in the version register is read as 2
(i.e. SDHCI_SPEC_300) based on the RTL provided by Cadence.
Socionext did not fix it up when it integrated the IP into the SoCs.
So, it is working as SDHCI v3.
It is not a real problem because there is no difference in the program
flow in sdhci.c between SDHCI_SPEC_300/400, but set the real version
just in case.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
__sdhci_read_caps() does not modify *ver, *caps, or *caps1.
Probably, the caller of this function will want to constifythe
parameters passed in.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDIO IRQ is not defaultly triggered by low level,
but by falling edge. It needs to set related register
to enable SDIO IRQ low level trigger function.
Otherwise the SDIO IRQ may be lost in some specail condition.
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Export sdhci_abort_tuning() function symbols which are used by other SD Host
controller driver modules.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Co-developed-by: Michael K Johnson <johnsonm@danlj.org>
Signed-off-by: Michael K Johnson <johnsonm@danlj.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The GL9750 and GL9755 chipsets, and possibly others, require PLL Enable
setup as part of the internal clock setup as described in 3.2.1 Internal
Clock Setup Sequence of SD Host Controller Simplified Specification
Version 4.20.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Co-developed-by: Michael K Johnson <johnsonm@danlj.org>
Signed-off-by: Michael K Johnson <johnsonm@danlj.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to section 3.2.1 internal clock setup in SD Host Controller
Simplified Specifications 4.20, the timeout of loop for checking
internal clock stable is defined as 150ms.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Co-developed-by: Michael K Johnson <johnsonm@danlj.org>
Signed-off-by: Michael K Johnson <johnsonm@danlj.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The current arasan sdhci PHY configuration isn't compatible
with the PHY on Intel's LGM(Lightning Mountain) SoC devices.
Therefore, add a new compatible, to adapt the Intel's LGM
eMMC PHY with arasan-sdhc controller to configure the PHY.
Signed-off-by: Ramuthevar Vadivel Muruganx <vadivel.muruganx.ramuthevar@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In case of error, the function of_platform_device_create() returns
NULL pointer not ERR_PTR(). The IS_ERR() test in the return value
check should be replaced with NULL test.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make sure the sdhost driver doesn't use requests bigger than SWIOTLB
can handle.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a minimal driver for ASPEED's SD controller, which exposes two
SDHCIs.
The ASPEED design implements a common register set for the SDHCIs, and
moves some of the standard configuration elements out to this common
area (e.g. 8-bit mode, and card detect configuration which is not
currently supported).
The SD controller has a dedicated hardware interrupt that is shared
between the slots. The common register set exposes information on which
slot triggered the interrupt; early revisions of the patch introduced an
irqchip for the register, but reality is it doesn't behave as an
irqchip, and the result fits awkwardly into the irqchip APIs. Instead
I've taken the simple approach of using the IRQ as a shared IRQ with
some minor performance impact for the second slot.
Ryan was the original author of the patch - I've taken his work and
massaged it to drop the irqchip support and rework the devicetree
integration. The driver has been smoke tested under qemu against a
minimal SD controller model and lightly tested on an ast2500-evb.
Signed-off-by: Ryan Chen <ryanchen.aspeed@gmail.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MSDC IP which support 64G DRAM will support 24bits BDMA buffer length,
so add support it.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
when plug out SD card, may get data CRC error, the MMC core will issue
CMD13 to get card status, then CMD13 timeout(due to card plug out) will
trigger CMD19 tuning, first CMD19 timeout has not call msdc_reset_hw()
and cause the next CMD19 gets controller busy.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All R-Car Gen3 SoCs with any ES version cannot use this DMAC actually.
So, this patch removes the compatibles of R-Car Gen3 SoCs from
renesas_sdhi_sys_dmac_of_match. Since the previous code has
an empty whitelist to prevent probing of R-Car Gen3 SoCs,
no behavior changes.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We don't need to set the 'slave_id' anymore - that field is never read
by the DMA driver.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix wrong code indentation which made the code hard to read, and fix
return with value in void function.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct sdhci_cdns_priv {
...
struct sdhci_cdns_phy_param phy_params[0];
};
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
So, replace the following form:
sizeof(*priv) + sizeof(priv->phy_params[0]) * nr_phy_params
with:
struct_size(priv, phy_params, nr_phy_params)
Also, notice that, in this case, variable priv_size is not necessary,
hence it is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch is to add erratum A011334 support in ls1028a 1.0 SoC
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-mmc@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/mmc/host/sdhci-s3c.c: In function 'sdhci_s3c_probe':
drivers/mmc/host/sdhci-s3c.c:613:19: warning: this statement may fall through [-Wimplicit-fallthrough=]
host->mmc->caps |= MMC_CAP_8_BIT_DATA;
drivers/mmc/host/sdhci-s3c.c:614:2: note: here
case 4:
^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/mmc/host/atmel-mci.c: In function 'atmci_get_cap':
drivers/mmc/host/atmel-mci.c:2415:30: warning: this statement may fall through [-Wimplicit-fallthrough=]
host->caps.has_odd_clk_div = 1;
~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~
drivers/mmc/host/atmel-mci.c:2416:2: note: here
case 0x400:
^~~~
drivers/mmc/host/atmel-mci.c:2422:28: warning: this statement may fall through [-Wimplicit-fallthrough=]
host->caps.has_highspeed = 1;
~~~~~~~~~~~~~~~~~~~~~~~~~^~~
drivers/mmc/host/atmel-mci.c:2423:2: note: here
case 0x200:
^~~~
drivers/mmc/host/atmel-mci.c:2426:40: warning: this statement may fall through [-Wimplicit-fallthrough=]
host->caps.need_notbusy_for_read_ops = 1;
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~
drivers/mmc/host/atmel-mci.c:2427:2: note: here
case 0x100:
^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
devm_platform_ioremap_resource() wraps platform_get_resource() and
devm_ioremap_resource() in a single helper, let's use that helper to
simplify the code.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The code dealing with busy detection is somewhat complicated. In a way to
make it a bit clearer, let's try to clarify the comments in the code about
it.
Additionally, move the part for clearing the so called busy start IRQ, to
the place where the IRQ is actually delivered. Ideally, this should make
the code a bit more robust.
Finally, to improve understanding of the code and the sequence of the busy
detection, move the corresponding code around a bit in mmci_cmd_irq().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Jean Nicolas GRAUX <jean-nicolas.graux@st.com>
Reviewed-by: Jean Nicolas GRAUX <jean-nicolas.graux@st.com>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The additional emmc2 interface of the BCM2711 is an improved version
of the old emmc controller, which is able to provide DDR50 mode on the
Raspberry Pi 4. Except 32 bit only register access no other quirks are
known yet.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the new helper devm_platform_ioremap_resource() which wraps the
platform_get_resource() and devm_ioremap_resource() together, to
simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit 414126f9e5.
This commit broke eMMC storage access on a new consumer MiniPC based on
AMD SoC, which has eMMC connected to:
02:00.0 SD Host controller: O2 Micro, Inc. Device 8620 (rev 01) (prog-if 01)
Subsystem: O2 Micro, Inc. Device 0002
During probe, several errors are seen including:
mmc1: Got data interrupt 0x02000000 even though no data operation was in progress.
mmc1: Timeout waiting for hardware interrupt.
mmc1: error -110 whilst initialising MMC card
Reverting this commit allows the eMMC storage to be detected & usable
again.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Fixes: 414126f9e5 ("mmc: sdhci: Remove unneeded quirk2 flag of O2 SD host
controller")
Cc: stable@vger.kernel.org # v5.1+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit 37fefadee8 ("mmc: bcm2835: Terminate timeout work
synchronously") causes lockups in case of hardware timeouts due the
timeout work also calling cancel_delayed_work_sync() on its own.
So revert it.
Fixes: 37fefadee8 ("mmc: bcm2835: Terminate timeout work synchronously")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Turns out the commit 3a0681c744 ("mmc: core: do not retry CMD6 in
__mmc_switch()") breaks initialization of a Toshiba THGBMNG5 eMMC card,
when using the meson-gx-mmc.c driver on a custom board based on Amlogic
A113D.
The CMD6 that switches the card into HS200 mode is then one that fails and
according to the below printed messages from the log:
[ 1.648951] mmc0: mmc_select_hs200 failed, error -84
[ 1.648988] mmc0: error -84 whilst initialising MMC card
After some analyze, it turns out that adding a delay of ~5ms inside
mmc_select_bus_width() but after mmc_compare_ext_csds() has been executed,
also fixes the problem. Adding yet some more debug code, trying to figure
out if potentially the card could be in a busy state, both by using CMD13
and ->card_busy() ops concluded that this was not the case.
Therefore, let's simply revert the commit that dropped support for retrying
of CMD6, as this also fixes the problem.
Fixes: 3a0681c744 ("mmc: core: do not retry CMD6 in __mmc_switch()")
Cc: stable@vger.kernel.org
Signed-off-by: Jan Kaisrlik <ja.kaisrlik@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Wolfram Sang