Changed bfin_get_ether_addr() to return a state and to
set no random mac address if the board don't provide one.
Let the caller of bfin_get_ether_addr() set a random mac
address if the return value is not 0.
v2: don't set random mac in bfin_get_ether_addr()
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Macro name for spi controller driver has been modified, so update default
board file accordingly.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
The serial TX IRQ is not simply (RX IRQ + 1) on some Blackfin chips,
so move the values to the platform resources.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
These particular files were just assuming that module.h was
somehow in the include paths. Give them the more minimalist
header file explicitly.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The default for the Blackfin SPI driver is 8 bits and dma disabled,
so many of the bfin5xx_spi_chip resources are redundant. So punt
those parts.
Further, drivers should themselves be declaring 16 bit transfers,
so for those that do, and for the ones which no longer do 16 bit
transfers, drop the bfin5xx_spi_chip resources.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
On bf518-ezbrd with DSA Ethernet switch enabled, on chip MAC is
connecting to phy at address 3. If allowing the netdevice framework to
probe both 3 phys of the switch when registering MAC phy, phy at address
1 is checked for link active status other than phy at address 3. If
connecting a cable to port 2 and leave port 1 open, link status in phy
2 and 3 are online, while that in phy 1 is offline. So, the phy layer
sets wrong offline status to net device on port 3. In this case, no data
can be transferred via ethernet port 2.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The SPORT/UART driver doesn't use the secondary channel pins, so don't
try and request them thus keeping other drivers from using them.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Move all the pin settings out of the Kconfig and into the platform
resources (MII vs RMII). This clean up also lets us push out the
phy settings so that board porters may control the layout.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This board has a SSM2603 codec, so make sure we have the right resources
declared for it.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The num_chipselect field for on-chip Blackfin SPI buses is supposed to
be 1 larger than the number of actual CSs available. This is because
the hardware starts counting at 1 and not 0. There is a field for "CS0",
but it is marked as "reserved" everywhere.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This lets people easily select the UART/SPORT consoles for early printk
while leveraging the pins declared in the boards file.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Rather than keeping the pins in the actual driver and worrying about a
mess of Kconfig options, declare all the desired pin resources in the
boards file. This lets people easily select the specific pins/ports for
the normal emulated UART as well as GPIOs for CTS/RTS.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Rather than keeping the pins in the actual driver and worrying about a
mess of Kconfig options, declare all the desired pin resources in the
boards file. This lets people easily select the specific pins/ports for
the normal UART as well as GPIOs for CTS/RTS.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The simple-gpio has been replaced by the gpio sysfs interface, so drop the
unused simple-gpio resources from all Blackfin boards.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Bill Gatliff & David Brownell pointed out we were missing some
copyrights, and licensing terms in some of the files in
./arch/blackfin, so this fixes things, and cleans them up.
It also removes:
- verbose GPL text(refer to the top level ./COPYING file)
- file names (you are looking at the file)
- bug url (it's in the ./MAINTAINERS file)
- "or later" on GPL-2, when we did not have that right
It also allows some Blackfin-specific assembly files to be under a BSD
like license (for people to use them outside of Linux).
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
These hardware devices are dead and the drivers never cleaned up/merged,
so punt the useless board resource info.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The "TWI_KEYPAD" driver was renamed to "INPUT_PCF8574", so update the
defines in the board resources accordingly.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The sed used to rename the bfin-twi-lcd only replaced the first instance
rather than all which led to the resources not being enabled when the
driver was built as a module.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The SPI flash on the BF518F-EZBRD board is actually hooked up to CS2,
not CS1, so make sure the resources are correct.
URL: http://blackfin.uclinux.org/gf/tracker/5220
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Blackfin SPI driver can be driven by an IRQ now, so declare it in
the board resources.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Try to keep the naming conventions consistent, so:
SPI_ADC_BF533 -> BFIN_SPI_ADC
TWI_LCD -> BFIN_TWI_LCD
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The two high address lines on the BF51x are not dedicated which means we
need to handle them like any other peripheral pin if we want to access the
upper 2MB of parallel flash.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Drop CONFIG_I2C_BOARDINFO ifdefs as the common i2c header handles this
already by stubbing things out
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
[Mike Frysinger <vapier.adi@gmail.com>:
- setup P_DEFAULT_BOOT_SPI_CS for every arch based on
the default bootrom behavior and convert all our boards
to it
- revert previous anomaly change ... bf51x is not affected
by anomaly 05000353]
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Danny Kukawka