PCI based SNI RM machines have their EISA bus behind an Intel PCI/EISA
bridge. So the PCI IO range must start at 0x0000. Changing that will
break the PCI bus, because i8259.c already has registered it's IO
addresses before the PCI bus gets initialized. Below is a patch,
which will register the PCI host bridge resources inside
register_pci_controller(). It also changes i8259.c to use insert_region(),
because request_resource() will fail, if the IO space of the PIT hanging
of the PCI host bridge (maybe passing the resource parent to
init_i8259_irqs() is a cleaner fix for that).
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch has merged GT64111 PCI routines and GT64120 PCI_0 routines.
GT64111 PCI is almost the same as GT64120's PCI_0.
This patch don't change GT64120 PCI routines.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
pcibios_fixup_device_resources() is called by pcibios_fixup_bus() which is
marked as __devinit.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This implementation has support for the concept of one separate ioport
address space by PCI domain. A pointer to the virtual address where
the port space of a domain has been mapped has been added to struct
pci_controller and systems should be fixed to fill in this value. For
single domain systems this will be the same value as passed to
set_io_port_base().
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Platforms will now have to supply a function dma_device_is_coherent which
returns if a particular device participates in the coherence domain. For
most platforms this function will always return 0 or 1.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move I8259A_IRQ_BASE from asm/i8259.h to asm/mach-generic/irq.h and
make it really customizable. And remove I8259_IRQ_BASE declared on
some platforms. Currently only NEC_CMBVR4133 is using custom
I8259A_IRQ_BASE value.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There's a serious typo in the function:
arch/mips/pci/ops-pnx8550.c:write_config_byte()
The parameter passed to the function config_access() is PCI_CMD_CONFIG_READ
instead of PCI_CMD_CONFIG_WRITE. This renders any attempts to write
a single byte to the PCI configuration registers useless.
This problem does not exist for write_config_word() nor write_config_dword().
This problem has been there since kernel v2.6.17 and is still there
as of kernel v2.6.19.1.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch has rewritten GALILEO_INL/GALILEO_OUTL using GT_READ/GT_WRITE.
This patch tested on Cobalt Qube2.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (39 commits)
Add missing maintainer countries in CREDITS
Fix bytes <-> kilobytes typo in Kconfig for ramdisk
fix a typo in Documentation/pi-futex.txt
BUG_ON conversion for fs/xfs/
BUG_ON() conversion in fs/nfsd/
BUG_ON conversion for fs/reiserfs
BUG_ON cleanups in arch/i386
BUG_ON cleanup in drivers/net/tokenring/
BUG_ON cleanup for drivers/md/
kerneldoc-typo in led-class.c
debugfs: spelling fix
rcutorture: Fix incorrect description of default for nreaders parameter
parport: Remove space in function calls
Michal Wronski: update contact info
Spelling fix: "control" instead of "cotrol"
reboot parameter in Documentation/kernel-parameters.txt
Fix copy&waste bug in comment in scripts/kernel-doc
remove duplicate "until" from kernel/workqueue.c
ite_gpio fix tabbage
fix file specification in comments
...
Fixed trivial path conflicts due to removed files:
arch/mips/dec/boot/decstation.c, drivers/char/ite_gpio.c
Many files include the filename at the beginning, serveral used a wrong one.
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
As per feature-removal-schedule.txt.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It was obesrved that at least one older PCI card predating the
requirement for the TRDY signal to respond within 16 clock ticks actually
does not meet this rule nor even the power-on defaults of the PCI bridges
found in development systems built around the Broadcom SiByte SOCs. Here
is a patch that bumps up the timeout to the highest finite value supported
by these chips, which is 255 clock ticks. The bridges affected are the
SiByte SOC itself and the SP1011.
This change does not effectively affect systems only having PCI option
cards installed that meet the TRDY requirement of the current PCI spec.
The rule was introduced with PCI 2.1, so any older card may make the
system affected. If this is the case, performance of the system will
suffer in return for the card working at all. If this is a concern, then
the solution is not to use such cards.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
The following change updates the Atlas interrupt handling to match that
of Malta. Tested with a 5Kc and a 34Kf successfully.
Signed-off-by: Maciej W. Rozycki <macro@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
I've encountered a serious problem with PCI config space access on Au1x000
platforms with recent 2.6.x-kernel. With 2.4.31 the same hardware works fine.
So I was looking for the differences:
Symptoms:
- no PCI-device is seen on bootup though two or three cards are present
- lspci output is empty
- OR: lspci shows 20 times the same device
(- OR: in some slot-configurations it worked anyhow)
System(s):
1. platform with Au1500 and three PCI-devices (actually a mycable XXS1500
with backplane for three PCI-devices)
2. platform with Au1550 and two PCI-devices (custom board)
Debugging:
I digged down to the config_access() of the au1xxx-processors in
arch/mips/pci/ops-au1000.c and switched on DEBUG.
The code of config_access() seems to be almost the same as of the
2.4.x-kernel. But the "pci_cfg_vm->addr" returned by get_vm_area(0x2000, 0)
once on booting is different. That's of course not forbidden. But the
alignment seems to be wrong. In my case, I received:
2.4.31: pci_cfg_vm->addr = c0000000
2.6.18-rc5: pci_cfg_vm->addr = c0101000
To make it short: With 2.6.x it fails on the first config-access with:
"PCI ERR detected: status 83a00356".
Fixup:
My fix is now, to use the VM_IOREMAP-flag in the get_vm_area call. This flag
seems to be introduced in mm/vmalloc.c a long time ago (in 2.6.7-bk13, I
found in gitweb).
Now, the returned address is pci_cfg_vm->addr = c0104000 and everything works
fine.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (33 commits)
[MIPS] Add missing backslashes to macro definitions.
[MIPS] Death list of board support to be removed after 2.6.18.
[MIPS] Remove BSD and Sys V compat data types.
[MIPS] ioc3.h: Uses u8, so include <linux/types.h>.
[MIPS] 74K: Assume it will also have an AR bit in config7
[MIPS] Treat CPUs with AR bit as physically indexed.
[MIPS] Oprofile: Support VSMP on 34K.
[MIPS] MIPS32/MIPS64 S-cache fix and cleanup
[MIPS] excite: PCI makefile needs to use += if it wants a chance to work.
[MIPS] excite: plat_setup -> plat_mem_setup.
[MIPS] au1xxx: export dbdma functions
[MIPS] au1xxx: dbdma, no sleeping under spin_lock
[MIPS] au1xxx: fix PSC_SMBTXRX_RSR.
[MIPS] Early printk for IP27.
[MIPS] Fix handling of 0 length I & D caches.
[MIPS] Typo fixes.
[MIPS] MIPS32/MIPS64 secondary cache management
[MIPS] Fix FIXADDR_TOP for TX39/TX49.
[MIPS] Remove first timer interrupt setup in wrppmc_timer_setup()
[MIPS] Fix configuration of R2 CPU features and multithreading.
...
Based on a patch series originally from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added support for RM200C machines with big endian firmware
Added support for RM200-C40 (R5000 support)
Signed-off-by: Florian Lohoff <flo@rfc822.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Support for the GT-64120-based Wind River 4KC PPMC Evaluation board.
Signed-off-by: Rongkai.Zhan <Rongkai.zhan@windriver.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Thomas Bogendoerfer