This happens when do stress test of uvc stream on/off which will
enable/disable endpoints. uvc has four tx requests, and may disable
endpoint between queue tx requests as following:
enable ep --> start qmu
queue tx request0
queue tx request1
queue tx request2 --> resume qmu
disable ep --> stop qmu may fail [1]
queue tx request3 --> will resume qmu, may cause qmu can't work
when enable ep next time [2]
[1]: when the tx fifo has some data to transmit, and
try to stop qmu (stop ep) meanwhile resume qmu (queue tx request),
it may cause stop qmu timeout, then can be fixed by flushing fifo
when stop qmu.
[2]: it resumes qmu again, shall stop qmu again.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reported-by: Min Guo <min.guo@mediatek.com>
Link: https://lore.kernel.org/r/20230119033322.21426-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the dr_mode is "host", after the host enter runtime suspend,
the mtu3 can't do it, because the mtu3's device wakeup function is
not enabled, instead it's enabled in gadget init function, to fix
the issue, init wakeup early in mtu3's probe()
Fixes: 6b587394c6 ("usb: mtu3: support suspend/resume for dual-role mode")
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reported-by: Tianping Fang <tianping.fang@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220929064459.32522-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Runtime verification infrastructure
This is the biggest change for this pull request. It introduces the
runtime verification that is necessary for running Linux on safety
critical systems. It allows for deterministic automata models to be
inserted into the kernel that will attach to tracepoints, where the
information on these tracepoints will move the model from state to state.
If a state is encountered that does not belong to the model, it will then
activate a given reactor, that could just inform the user or even panic
the kernel (for which safety critical systems will detect and can recover
from).
- Two monitor models are also added: Wakeup In Preemptive (WIP - not to be
confused with "work in progress"), and Wakeup While Not Running (WWNR).
- Added __vstring() helper to the TRACE_EVENT() macro to replace several
vsnprintf() usages that were all doing it wrong.
- eprobes now can have their event autogenerated when the event name is left
off.
- The rest is various cleanups and fixes.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCYu0yzRQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qj4HAP4tQtV55rjj4DQ5XIXmtI3/64PmyRSJ
+y4DEXi1UvEUCQD/QAuQfWoT/7gh35ltkfeS4t3ockzy14rrkP5drZigiQA=
=kEtM
-----END PGP SIGNATURE-----
Merge tag 'trace-v6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
- Runtime verification infrastructure
This is the biggest change here. It introduces the runtime
verification that is necessary for running Linux on safety critical
systems.
It allows for deterministic automata models to be inserted into the
kernel that will attach to tracepoints, where the information on
these tracepoints will move the model from state to state.
If a state is encountered that does not belong to the model, it will
then activate a given reactor, that could just inform the user or
even panic the kernel (for which safety critical systems will detect
and can recover from).
- Two monitor models are also added: Wakeup In Preemptive (WIP - not to
be confused with "work in progress"), and Wakeup While Not Running
(WWNR).
- Added __vstring() helper to the TRACE_EVENT() macro to replace
several vsnprintf() usages that were all doing it wrong.
- eprobes now can have their event autogenerated when the event name is
left off.
- The rest is various cleanups and fixes.
* tag 'trace-v6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (50 commits)
rv: Unlock on error path in rv_unregister_reactor()
tracing: Use alignof__(struct {type b;}) instead of offsetof()
tracing/eprobe: Show syntax error logs in error_log file
scripts/tracing: Fix typo 'the the' in comment
tracepoints: It is CONFIG_TRACEPOINTS not CONFIG_TRACEPOINT
tracing: Use free_trace_buffer() in allocate_trace_buffers()
tracing: Use a struct alignof to determine trace event field alignment
rv/reactor: Add the panic reactor
rv/reactor: Add the printk reactor
rv/monitor: Add the wwnr monitor
rv/monitor: Add the wip monitor
rv/monitor: Add the wip monitor skeleton created by dot2k
Documentation/rv: Add deterministic automata instrumentation documentation
Documentation/rv: Add deterministic automata monitor synthesis documentation
tools/rv: Add dot2k
Documentation/rv: Add deterministic automaton documentation
tools/rv: Add dot2c
Documentation/rv: Add a basic documentation
rv/include: Add instrumentation helper functions
rv/include: Add deterministic automata monitor definition via C macros
...
Instead of open coding a __dynamic_array() with a fixed length (which
defeats the purpose of the dynamic array in the first place). Use the new
__vstring() helper that will use a va_list and only write enough of the
string into the ring buffer that is needed.
Link: https://lkml.kernel.org/r/20220719112719.17e796c6@gandalf.local.home
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-usb@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Add function wake notification to support function remote wakeup,
currently assume the composite device only enable function wake
for the first interface.
Forward request to function driver when the recipient is an interface,
including:
GetStatus() request to the first interface in a function returns the
information about 'function remote wakeup' and 'function remote wakeup
capalbe';
SetFeature request of FUNCTION_SUSPEND to an interface recipient, the
controller driver saves the suspend option;
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220708071903.25752-5-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is capable of supporting usb3 dual role if there is at least one
usb3 port for device and xhci controller, we can check it from the
controller's capability, so no need the property "mediatek,usb3-drd"
anymore, but I find the property is not decribed in dt-binding.
Meanwhile, also take into account if the u3 port is disabled when the
u3 phy is shared with pcie.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220708071903.25752-4-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We may want to disable device's usb3 port when the combo phy is switched
from usb3 mode to pcie mode for some projects.
Meanwhile rename member @is_u3_ip to @u3_capable to avoid misleading, due
to the member's value may be changed when disable usb3 port, but the
controller is still a usb3 IP which also tells us how to manage the fifo.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220708071903.25752-3-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register gadget irq to avoid the interrupt handler is occurred
or scheduled during the unbind flow, may happen when do android
function switch stress test.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220609074233.15532-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support controller reset via a reset-controller usually in infracfg,
it's different with the software reset by IPPC which only used to reset MAC,
and it will also reset IPPC meanwhile.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220523090449.14430-4-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Issue description:
When an OTG port has been switched to device role and then switch back
to host role again, the USB 3.0 Host (XHCI) will not be able to detect
"plug in event of a connected USB 2.0/1.0 ((Highspeed and Fullspeed)
devices until system reboot.
Root cause and Solution:
There is a condition checking flag "ssusb->otg_switch.is_u3_drd" in
toggle_opstate(). At the end of role switch procedure, toggle_opstate()
will be called to set DC_SESSION and SOFT_CONN bit. If "is_u3_drd" was
set and switched the role to USB host 3.0, bit DC_SESSION and SOFT_CONN
will be skipped hence caused the port cannot detect connected USB 2.0
(Highspeed and Fullspeed) devices. Simply remove the condition check to
solve this issue.
Fixes: d0ed062a8b ("usb: mtu3: dual-role mode support")
Cc: stable@vger.kernel.org
Tested-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Signed-off-by: Tainping Fang <tianping.fang@mediatek.com>
Link: https://lore.kernel.org/r/20220419081245.21015-1-macpaul.lin@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a seldom issue that the controller access invalid address
and trigger devapc or emimpu violation. That is due to memory access
is out of order and cause gpd data is not correct.
Add mb() to prohibit compiler or cpu from reordering to make sure GPD
is fully written before setting its HWO.
Fixes: 48e0d3735a ("usb: mtu3: supports new QMU format")
Cc: stable@vger.kernel.org
Reported-by: Eddie Hung <eddie.hung@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20211218095749.6250-2-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the Interval value from isoc/intr endpoint descriptor, no need
minus one. The original code doesn't cause transfer error for
normal cases, but it may have side effect with respond time of ERDY
or tPingTimeout.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20211218095749.6250-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new API dev_pm_set_dedicated_wake_irq_reverse() to request
dedicated wake-up interrupt, due to we want to enable the wake IRQ
after running ->runtime_suspend().
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some platforms, e.g. 8183/8192, use low level latch way to keep
wakeup signal, it may latch a wrong signal if debounce more time,
and enable wakeup earlier.
____________________
ip_sleep ____/ \__________
___________________
wakeup_signal ____________/ \______
_______________________________
wakeup_en _______/
^ ^
|(1) |(2)
latch wakeup_signal mistakenly at (1), should latch it at (2);
Workaround: delay about 100us to enable wakeup, meanwhile decrease
debounce time.
Fixes: b1a344589e ("usb: mtu3: support ip-sleep wakeup for MT8183")
Cc: stable@vger.kernel.org
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20210826083637.33237-2-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Forgot 'return 0;' when suspend successfully, make the mistake
when I split patches.
Fixes: 6b587394c6 ("usb: mtu3: support suspend/resume for dual-role mode")
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20210826083637.33237-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support suspend/resume for dual-role mode including the single
port and multi-ports supported by host controller, when the host
supports mult-ports, only port0 (u2/u3) is used to support dual
role mode.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1626340078-29111-14-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a dedicated wakeup irq for runtime suspend/resume, and interrupts
names are provided if using wakeup irq, this patch only support host
mode.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1626340078-29111-11-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support to disable specific usb2 host ports, it's useful when
a usb2 port is disabled on some platforms, but enabled on others
for the same SoC.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1626340078-29111-9-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use common helper ssusb_set_mode() to do role switch instead
of manual switch helper;
Remove unnecessary local variable when get role status
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1623139069-8173-14-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now we mainly use usb-role-switch to set dual role mode, and all
three ways supported use the same function to switch mode, use
usb_role enum will make code clear
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1623139069-8173-10-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When power down device IP, we can also power down device port,
then power on the port again when power on device ip, it's helpful
to make device ip enter ip sleep mode.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1623139069-8173-7-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support ip-sleep wakeup for MT8183, it's similar to MT8173,
and it's also a specific one, but not following IPM rule.
Due to the index 2 already used by many DTS, it's better to keep
it unchanged for backward compatibility, treat specific ones without
following IPM rule as revision 1.x, meanwhile reserve 3~10 for later
revision that follows the IPM rule.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1616482975-17841-10-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable u3_ports_disabed contains a spelling mistake,
rename it to u3_ports_disabled.
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210311092529.4898-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This code is using the wrong sizeof() so it does not allocate enough
memory. It allocates 32 bytes but 72 are required. That will lead to
memory corruption.
Fixes: ae07809255 ("usb: mtu3: add debugfs interface files")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/X8ikqc4Mo2/0G72j@mwanda
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chunfeng Yun