When configured as a specific low power state: MFP_LPM_DRIVE_LOW,
MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during
low power mode shall be re-configured as output (if they are not
configured so), thus the PGSRx bits can output.
Create an additional low power values GPDR registers, and properly
save/restore the GAFR + GPDR registers when doing suspend/resume.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Due to the problem of reset status bits being handled by different
registers between pxa2xx and pxa3xx, introduce a global reset_status
variable, initialized by SoC-specific code and later being used by
other drivers.
And also introduce clear_reset_status(), which is used to clear the
corresponding status bits. Pass RESET_STATUS_ALL to clear all bits.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
MFP configurations after resume should be done before the GPIO registers
are restored. Move the mfp sysdev registeration to the same place where
GPIO and IRQ sysdev(s) are registered to better control the order.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
To further clean up the GPIO and IRQ structure:
1. pxa_init_irq_gpio() and pxa_init_gpio() combines into a single
function pxa_init_gpio()
2. assignment of set_wake merged into pxa_init_{irq,gpio}() as
an argument
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This makes the code better organized and simplified a bit. The change
will lose a bit of performance when performing IRQ ack/mask/unmask,but
that's not too much after checking the result binary.
This patch also removes the ugly #ifdef CONFIG_PXA27x .. #endif by
carefully not to access those pxa{27x,3xx} specific registers, this
is done by keeping an internal IRQ number variable. The pxa-regs.h
is also modified so registers for IRQ > PXA_IRQ(31) are made public
even if CONFIG_PXA{27x,3xx} isn't defined (for pxa25x's sake)
The incorrect assumption in the original code that internal irq starts
from 0 is also corrected by comparing with PXA_IRQ(0).
"struct sys_device" for the IRQ are reduced into one single device on
pxa{27x,3xx}.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds gpiolib support for the PXA architecture:
- move all GPIO API functions from generic.c into gpio.c
- convert the gpio_get/set_value macros into inline functions
This makes it easier to hook up GPIOs provided by external chips like
ASICs and CPLDs.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Minor ARM fixup from David Brownell folded into this ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
a function pxa_init_irq_set_wake() was introduced, so that
processor specific code could install their own version
code setting PFER and PRER registers within pxa_gpio_irq_type
are removed, and the edge configuration is postponed to the
(*set_wake) and copies the GRER and GFER register, which will
always be set up correctly by pxa_gpio_irq_type()
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This definition produces processor specific code in generic function
pxa_gpio_mode(), thus creating inconsistencies for support of pxa25x
and pxa27x in a single zImage.
As David Brownell suggests, make it a run-time variable and initialize
at run-time according to the number of GPIOs on the processor. For now
the initialization happens in pxa_init_irq_gpio(), since there is
already a parameter for that, besides, this is and MUST be earlier
than any subsequent calls to pxa_gpio_mode().
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
get_lcdclk_frequency_10khz() is now redundant, remove it. Hide
pxa27x_get_lcdclk_frequency_10khz() from public view.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rename pxa25x and pxa27x memory/lcd/core clock functions, and
select the correct version at run time.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This allows individual CPU support to determine which platform
devices should be registered. Also fix a copy-n-paste bug in
the I2C power platform device entry.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
/* should be ok this time, I aligned this patch to your arm:pxa2.mbox */
1. move pxa25x specific IRQ initialization code to pxa25x_init_irq()
and pxa27x code to pxa27x_init_irq(), remove pxa_init_irq()
2. replace all pxa_init_irq() with their PXA25x or PXA27x specific
functions
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Eric Miao