Update comment typo _consisitent_ to _consistent_ from following commit.
commit 0206319fdf ("blk-mq: Fix poll_stat for new size-based bucketing.")
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull block updates from Jens Axboe:
"This is the main pull request for block IO related changes for the
4.16 kernel. Nothing major in this pull request, but a good amount of
improvements and fixes all over the map. This contains:
- BFQ improvements, fixes, and cleanups from Angelo, Chiara, and
Paolo.
- Support for SMR zones for deadline and mq-deadline from Damien and
Christoph.
- Set of fixes for bcache by way of Michael Lyle, including fixes
from himself, Kent, Rui, Tang, and Coly.
- Series from Matias for lightnvm with fixes from Hans Holmberg,
Javier, and Matias. Mostly centered around pblk, and the removing
rrpc 1.2 in preparation for supporting 2.0.
- A couple of NVMe pull requests from Christoph. Nothing major in
here, just fixes and cleanups, and support for command tracing from
Johannes.
- Support for blk-throttle for tracking reads and writes separately.
From Joseph Qi. A few cleanups/fixes also for blk-throttle from
Weiping.
- Series from Mike Snitzer that enables dm to register its queue more
logically, something that's alwways been problematic on dm since
it's a stacked device.
- Series from Ming cleaning up some of the bio accessor use, in
preparation for supporting multipage bvecs.
- Various fixes from Ming closing up holes around queue mapping and
quiescing.
- BSD partition fix from Richard Narron, fixing a problem where we
can't mount newer (10/11) FreeBSD partitions.
- Series from Tejun reworking blk-mq timeout handling. The previous
scheme relied on atomic bits, but it had races where we would think
a request had timed out if it to reused at the wrong time.
- null_blk now supports faking timeouts, to enable us to better
exercise and test that functionality separately. From me.
- Kill the separate atomic poll bit in the request struct. After
this, we don't use the atomic bits on blk-mq anymore at all. From
me.
- sgl_alloc/free helpers from Bart.
- Heavily contended tag case scalability improvement from me.
- Various little fixes and cleanups from Arnd, Bart, Corentin,
Douglas, Eryu, Goldwyn, and myself"
* 'for-4.16/block' of git://git.kernel.dk/linux-block: (186 commits)
block: remove smart1,2.h
nvme: add tracepoint for nvme_complete_rq
nvme: add tracepoint for nvme_setup_cmd
nvme-pci: introduce RECONNECTING state to mark initializing procedure
nvme-rdma: remove redundant boolean for inline_data
nvme: don't free uuid pointer before printing it
nvme-pci: Suspend queues after deleting them
bsg: use pr_debug instead of hand crafted macros
blk-mq-debugfs: don't allow write on attributes with seq_operations set
nvme-pci: Fix queue double allocations
block: Set BIO_TRACE_COMPLETION on new bio during split
blk-throttle: use queue_is_rq_based
block: Remove kblockd_schedule_delayed_work{,_on}()
blk-mq: Avoid that blk_mq_delay_run_hw_queue() introduces unintended delays
blk-mq: Rename blk_mq_request_direct_issue() into blk_mq_request_issue_directly()
lib/scatterlist: Fix chaining support in sgl_alloc_order()
blk-throttle: track read and write request individually
block: add bdev_read_only() checks to common helpers
block: fail op_is_write() requests to read-only partitions
blk-throttle: export io_serviced_recursive, io_service_bytes_recursive
...
The previous patch removed all users of these two functions. Hence
also remove the functions themselves.
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move completion related items (like the call single data) near the
end of the struct, instead of mixing them in with the initial
queueing related fields.
Move queuelist below the bio structures. Then we have all
queueing related bits in the first cache line.
This yields a 1.5-2% increase in IOPS for a null_blk test, both for
sync and for high thread count access. Sync test goes form 975K to
992K, 32-thread case from 20.8M to 21.2M IOPS.
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We only have one atomic flag left. Instead of using an entire
unsigned long for that, steal the bottom bit of the deadline
field that we already reserved.
Remove ->atomic_flags, since it's now unused.
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We reduce the resolution of request expiry, but since we're already
using jiffies for this where resolution depends on the kernel
configuration and since the timeout resolution is coarse anyway,
that should be fine.
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We don't need this to be an atomic flag, it can be a regular
flag. We either end up on the same CPU for the polling, in which
case the state is sane, or we did the sleep which would imply
the needed barrier to ensure we see the right state.
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
After the recent updates to use generation number and state based
synchronization, blk-mq no longer depends on REQ_ATOM_COMPLETE except
to avoid firing the same timeout multiple times.
Remove all REQ_ATOM_COMPLETE usages and use a new rq_flags flag
RQF_MQ_TIMEOUT_EXPIRED to avoid firing the same timeout multiple
times. This removes atomic bitops from hot paths too.
v2: Removed blk_clear_rq_complete() from blk_mq_rq_timed_out().
v3: Added RQF_MQ_TIMEOUT_EXPIRED flag.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "jianchao.wang" <jianchao.w.wang@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently, blk-mq timeout path synchronizes against the usual
issue/completion path using a complex scheme involving atomic
bitflags, REQ_ATOM_*, memory barriers and subtle memory coherence
rules. Unfortunately, it contains quite a few holes.
There's a complex dancing around REQ_ATOM_STARTED and
REQ_ATOM_COMPLETE between issue/completion and timeout paths; however,
they don't have a synchronization point across request recycle
instances and it isn't clear what the barriers add.
blk_mq_check_expired() can easily read STARTED from N-2'th iteration,
deadline from N-1'th, blk_mark_rq_complete() against Nth instance.
In fact, it's pretty easy to make blk_mq_check_expired() terminate a
later instance of a request. If we induce 5 sec delay before
time_after_eq() test in blk_mq_check_expired(), shorten the timeout to
2s, and issue back-to-back large IOs, blk-mq starts timing out
requests spuriously pretty quickly. Nothing actually timed out. It
just made the call on a recycle instance of a request and then
terminated a later instance long after the original instance finished.
The scenario isn't theoretical either.
This patch replaces the broken synchronization mechanism with a RCU
and generation number based one.
1. Each request has a u64 generation + state value, which can be
updated only by the request owner. Whenever a request becomes
in-flight, the generation number gets bumped up too. This provides
the basis for the timeout path to distinguish different recycle
instances of the request.
Also, marking a request in-flight and setting its deadline are
protected with a seqcount so that the timeout path can fetch both
values coherently.
2. The timeout path fetches the generation, state and deadline. If
the verdict is timeout, it records the generation into a dedicated
request abortion field and does RCU wait.
3. The completion path is also protected by RCU (from the previous
patch) and checks whether the current generation number and state
match the abortion field. If so, it skips completion.
4. The timeout path, after RCU wait, scans requests again and
terminates the ones whose generation and state still match the ones
requested for abortion.
By now, the timeout path knows that either the generation number
and state changed if it lost the race or the completion will yield
to it and can safely timeout the request.
While it's more lines of code, it's conceptually simpler, doesn't
depend on direct use of subtle memory ordering or coherence, and
hopefully doesn't terminate the wrong instance.
While this change makes REQ_ATOM_COMPLETE synchronization unnecessary
between issue/complete and timeout paths, REQ_ATOM_COMPLETE isn't
removed yet as it's still used in other places. Future patches will
move all state tracking to the new mechanism and remove all bitops in
the hot paths.
Note that this patch adds a comment explaining a race condition in
BLK_EH_RESET_TIMER path. The race has always been there and this
patch doesn't change it. It's just documenting the existing race.
v2: - Fixed BLK_EH_RESET_TIMER handling as pointed out by Jianchao.
- s/request->gstate_seqc/request->gstate_seq/ as suggested by Peter.
- READ_ONCE() added in blk_mq_rq_update_state() as suggested by Peter.
v3: - Fixed possible extended seqcount / u64_stats_sync read looping
spotted by Peter.
- MQ_RQ_IDLE was incorrectly being set in complete_request instead
of free_request. Fixed.
v4: - Rebased on top of hctx_lock() refactoring patch.
- Added comment explaining the use of hctx_lock() in completion path.
v5: - Added comments requested by Bart.
- Note the addition of BLK_EH_RESET_TIMER race condition in the
commit message.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "jianchao.wang" <jianchao.w.wang@oracle.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Bart Van Assche <Bart.VanAssche@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Components relying only on the request_queue structure for accessing
block devices (e.g. I/O schedulers) have a limited knowledged of the
device characteristics. In particular, the device capacity cannot be
easily discovered, which for a zoned block device also result in the
inability to easily know the number of zones of the device (the zone
size is indicated by the chunk_sectors field of the queue limits).
Introduce the nr_zones field to the request_queue structure to simplify
access to this information. Also, add the bitmap seq_zone_bitmap which
indicates which zones of the device are sequential zones (write
preferred or write required) and the bitmap seq_zones_wlock which
indicates if a zone is write locked, that is, if a write request
targeting a zone was dispatched to the device. These fields are
initialized by the low level block device driver (sd.c for ZBC/ZAC
disks). They are not initialized by stacking drivers (device mappers)
handling zoned block devices (e.g. dm-linear).
Using this, I/O schedulers can introduce zone write locking to control
request dispatching to a zoned block device and avoid write request
reordering by limiting to at most a single write request per zone
outside of the scheduler at any time.
Based on previous patches from Damien Le Moal.
Signed-off-by: Christoph Hellwig <hch@lst.de>
[Damien]
* Fixed comments and identation in blkdev.h
* Changed helper functions
* Fixed this commit message
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A previous change blindly added massive alignment to the
call_single_data structure in struct request. This ballooned it in size
from 296 to 320 bytes on my setup, for no valid reason at all.
Use the unaligned struct __call_single_data variant instead.
Fixes: 966a967116 ("smp: Avoid using two cache lines for struct call_single_data")
Cc: stable@vger.kernel.org # v4.14
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit caa4b02476e3(blk-map: call blk_queue_bounce from blk_rq_append_bio)
moves blk_queue_bounce() into blk_rq_append_bio(), but don't consider
the fact that the bounced bio becomes invisible to caller since the
parameter type is 'struct bio *'. Make it a pointer to a pointer to
a bio, so the caller sees the right bio also after a bounce.
Fixes: caa4b02476 ("blk-map: call blk_queue_bounce from blk_rq_append_bio")
Cc: Christoph Hellwig <hch@lst.de>
Reported-by: Michele Ballabio <barra_cuda@katamail.com>
(handling failure of blk_rq_append_bio(), only call bio_get() after
blk_rq_append_bio() returns OK)
Tested-by: Michele Ballabio <barra_cuda@katamail.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit a8821f3f3("block: Improvements to bounce-buffer handling") tries
to make sure that the bio to .make_request_fn won't exceed BIO_MAX_PAGES,
but ignores that passthrough I/O can use blk_queue_bounce() too.
Especially, passthrough IO may not be sector-aligned, and the check
of 'sectors < bio_sectors(*bio_orig)' inside __blk_queue_bounce() may
become true even though the max bvec number doesn't exceed BIO_MAX_PAGES,
then cause the bio splitted, and the original passthrough bio is submited
to generic_make_request().
This patch fixes this issue by checking if the bio is passthrough IO,
and use bio_kmalloc() to allocate the cloned passthrough bio.
Cc: NeilBrown <neilb@suse.com>
Fixes: a8821f3f3("block: Improvements to bounce-buffer handling")
Tested-by: Michele Ballabio <barra_cuda@katamail.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull core block layer updates from Jens Axboe:
"This is the main pull request for block storage for 4.15-rc1.
Nothing out of the ordinary in here, and no API changes or anything
like that. Just various new features for drivers, core changes, etc.
In particular, this pull request contains:
- A patch series from Bart, closing the whole on blk/scsi-mq queue
quescing.
- A series from Christoph, building towards hidden gendisks (for
multipath) and ability to move bio chains around.
- NVMe
- Support for native multipath for NVMe (Christoph).
- Userspace notifications for AENs (Keith).
- Command side-effects support (Keith).
- SGL support (Chaitanya Kulkarni)
- FC fixes and improvements (James Smart)
- Lots of fixes and tweaks (Various)
- bcache
- New maintainer (Michael Lyle)
- Writeback control improvements (Michael)
- Various fixes (Coly, Elena, Eric, Liang, et al)
- lightnvm updates, mostly centered around the pblk interface
(Javier, Hans, and Rakesh).
- Removal of unused bio/bvec kmap atomic interfaces (me, Christoph)
- Writeback series that fix the much discussed hundreds of millions
of sync-all units. This goes all the way, as discussed previously
(me).
- Fix for missing wakeup on writeback timer adjustments (Yafang
Shao).
- Fix laptop mode on blk-mq (me).
- {mq,name} tupple lookup for IO schedulers, allowing us to have
alias names. This means you can use 'deadline' on both !mq and on
mq (where it's called mq-deadline). (me).
- blktrace race fix, oopsing on sg load (me).
- blk-mq optimizations (me).
- Obscure waitqueue race fix for kyber (Omar).
- NBD fixes (Josef).
- Disable writeback throttling by default on bfq, like we do on cfq
(Luca Miccio).
- Series from Ming that enable us to treat flush requests on blk-mq
like any other request. This is a really nice cleanup.
- Series from Ming that improves merging on blk-mq with schedulers,
getting us closer to flipping the switch on scsi-mq again.
- BFQ updates (Paolo).
- blk-mq atomic flags memory ordering fixes (Peter Z).
- Loop cgroup support (Shaohua).
- Lots of minor fixes from lots of different folks, both for core and
driver code"
* 'for-4.15/block' of git://git.kernel.dk/linux-block: (294 commits)
nvme: fix visibility of "uuid" ns attribute
blk-mq: fixup some comment typos and lengths
ide: ide-atapi: fix compile error with defining macro DEBUG
blk-mq: improve tag waiting setup for non-shared tags
brd: remove unused brd_mutex
blk-mq: only run the hardware queue if IO is pending
block: avoid null pointer dereference on null disk
fs: guard_bio_eod() needs to consider partitions
xtensa/simdisk: fix compile error
nvme: expose subsys attribute to sysfs
nvme: create 'slaves' and 'holders' entries for hidden controllers
block: create 'slaves' and 'holders' entries for hidden gendisks
nvme: also expose the namespace identification sysfs files for mpath nodes
nvme: implement multipath access to nvme subsystems
nvme: track shared namespaces
nvme: introduce a nvme_ns_ids structure
nvme: track subsystems
block, nvme: Introduce blk_mq_req_flags_t
block, scsi: Make SCSI quiesce and resume work reliably
block: Add the QUEUE_FLAG_PREEMPT_ONLY request queue flag
...
Several block layer and NVMe core functions accept a combination
of BLK_MQ_REQ_* flags through the 'flags' argument but there is
no verification at compile time whether the right type of block
layer flags is passed. Make it possible for sparse to verify this.
This patch does not change any functionality.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Cc: linux-nvme@lists.infradead.org
Cc: Christoph Hellwig <hch@lst.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The contexts from which a SCSI device can be quiesced or resumed are:
* Writing into /sys/class/scsi_device/*/device/state.
* SCSI parallel (SPI) domain validation.
* The SCSI device power management methods. See also scsi_bus_pm_ops.
It is essential during suspend and resume that neither the filesystem
state nor the filesystem metadata in RAM changes. This is why while
the hibernation image is being written or restored that SCSI devices
are quiesced. The SCSI core quiesces devices through scsi_device_quiesce()
and scsi_device_resume(). In the SDEV_QUIESCE state execution of
non-preempt requests is deferred. This is realized by returning
BLKPREP_DEFER from inside scsi_prep_state_check() for quiesced SCSI
devices. Avoid that a full queue prevents power management requests
to be submitted by deferring allocation of non-preempt requests for
devices in the quiesced state. This patch has been tested by running
the following commands and by verifying that after each resume the
fio job was still running:
for ((i=0; i<10; i++)); do
(
cd /sys/block/md0/md &&
while true; do
[ "$(<sync_action)" = "idle" ] && echo check > sync_action
sleep 1
done
) &
pids=($!)
for d in /sys/class/block/sd*[a-z]; do
bdev=${d#/sys/class/block/}
hcil=$(readlink "$d/device")
hcil=${hcil#../../../}
echo 4 > "$d/queue/nr_requests"
echo 1 > "/sys/class/scsi_device/$hcil/device/queue_depth"
fio --name="$bdev" --filename="/dev/$bdev" --buffered=0 --bs=512 \
--rw=randread --ioengine=libaio --numjobs=4 --iodepth=16 \
--iodepth_batch=1 --thread --loops=$((2**31)) &
pids+=($!)
done
sleep 1
echo "$(date) Hibernating ..." >>hibernate-test-log.txt
systemctl hibernate
sleep 10
kill "${pids[@]}"
echo idle > /sys/block/md0/md/sync_action
wait
echo "$(date) Done." >>hibernate-test-log.txt
done
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
References: "I/O hangs after resuming from suspend-to-ram" (https://marc.info/?l=linux-block&m=150340235201348).
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Martin Steigerwald <martin@lichtvoll.de>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This flag will be used in the next patch to let the block layer
core know whether or not a SCSI request queue has been quiesced.
A quiesced SCSI queue namely only processes RQF_PREEMPT requests.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Martin Steigerwald <martin@lichtvoll.de>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A side effect of this patch is that the GFP mask that is passed to
several allocation functions in the legacy block layer is changed
from GFP_KERNEL into __GFP_DIRECT_RECLAIM.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Martin Steigerwald <martin@lichtvoll.de>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
That we we can also poll non blk-mq queues. Mostly needed for
the NVMe multipath code, but could also be useful elsewhere.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This helpers allows to bounce steal the uncompleted bios from a request so
that they can be reissued on another path.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This helper allows reinserting a bio into a new queue without much
overhead, but requires all queue limits to be the same for the upper
and lower queues, and it does not provide any recursion preventions.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Javier González <javier@cnexlabs.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We already have a queue_is_rq_based helper to check if a request_queue
is request based, so we can remove the flag for it.
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The lockdep code had reported the following unsafe locking scenario:
CPU0 CPU1
---- ----
lock(s_active#228);
lock(&bdev->bd_mutex/1);
lock(s_active#228);
lock(&bdev->bd_mutex);
*** DEADLOCK ***
The deadlock may happen when one task (CPU1) is trying to delete a
partition in a block device and another task (CPU0) is accessing
tracing sysfs file (e.g. /sys/block/dm-1/trace/act_mask) in that
partition.
The s_active isn't an actual lock. It is a reference count (kn->count)
on the sysfs (kernfs) file. Removal of a sysfs file, however, require
a wait until all the references are gone. The reference count is
treated like a rwsem using lockdep instrumentation code.
The fact that a thread is in the sysfs callback method or in the
ioctl call means there is a reference to the opended sysfs or device
file. That should prevent the underlying block structure from being
removed.
Instead of using bd_mutex in the block_device structure, a new
blk_trace_mutex is now added to the request_queue structure to protect
access to the blk_trace structure.
Suggested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Waiman Long <longman@redhat.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Fix typo in patch subject line, and prune a comment detailing how
the code used to work.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull block layer updates from Jens Axboe:
"This is the first pull request for 4.14, containing most of the code
changes. It's a quiet series this round, which I think we needed after
the churn of the last few series. This contains:
- Fix for a registration race in loop, from Anton Volkov.
- Overflow complaint fix from Arnd for DAC960.
- Series of drbd changes from the usual suspects.
- Conversion of the stec/skd driver to blk-mq. From Bart.
- A few BFQ improvements/fixes from Paolo.
- CFQ improvement from Ritesh, allowing idling for group idle.
- A few fixes found by Dan's smatch, courtesy of Dan.
- A warning fixup for a race between changing the IO scheduler and
device remova. From David Jeffery.
- A few nbd fixes from Josef.
- Support for cgroup info in blktrace, from Shaohua.
- Also from Shaohua, new features in the null_blk driver to allow it
to actually hold data, among other things.
- Various corner cases and error handling fixes from Weiping Zhang.
- Improvements to the IO stats tracking for blk-mq from me. Can
drastically improve performance for fast devices and/or big
machines.
- Series from Christoph removing bi_bdev as being needed for IO
submission, in preparation for nvme multipathing code.
- Series from Bart, including various cleanups and fixes for switch
fall through case complaints"
* 'for-4.14/block' of git://git.kernel.dk/linux-block: (162 commits)
kernfs: checking for IS_ERR() instead of NULL
drbd: remove BIOSET_NEED_RESCUER flag from drbd_{md_,}io_bio_set
drbd: Fix allyesconfig build, fix recent commit
drbd: switch from kmalloc() to kmalloc_array()
drbd: abort drbd_start_resync if there is no connection
drbd: move global variables to drbd namespace and make some static
drbd: rename "usermode_helper" to "drbd_usermode_helper"
drbd: fix race between handshake and admin disconnect/down
drbd: fix potential deadlock when trying to detach during handshake
drbd: A single dot should be put into a sequence.
drbd: fix rmmod cleanup, remove _all_ debugfs entries
drbd: Use setup_timer() instead of init_timer() to simplify the code.
drbd: fix potential get_ldev/put_ldev refcount imbalance during attach
drbd: new disk-option disable-write-same
drbd: Fix resource role for newly created resources in events2
drbd: mark symbols static where possible
drbd: Send P_NEG_ACK upon write error in protocol != C
drbd: add explicit plugging when submitting batches
drbd: change list_for_each_safe to while(list_first_entry_or_null)
drbd: introduce drbd_recv_header_maybe_unplug
...
struct call_single_data is used in IPIs to transfer information between
CPUs. Its size is bigger than sizeof(unsigned long) and less than
cache line size. Currently it is not allocated with any explicit alignment
requirements. This makes it possible for allocated call_single_data to
cross two cache lines, which results in double the number of the cache lines
that need to be transferred among CPUs.
This can be fixed by requiring call_single_data to be aligned with the
size of call_single_data. Currently the size of call_single_data is the
power of 2. If we add new fields to call_single_data, we may need to
add padding to make sure the size of new definition is the power of 2
as well.
Fortunately, this is enforced by GCC, which will report bad sizes.
To set alignment requirements of call_single_data to the size of
call_single_data, a struct definition and a typedef is used.
To test the effect of the patch, I used the vm-scalability multiple
thread swap test case (swap-w-seq-mt). The test will create multiple
threads and each thread will eat memory until all RAM and part of swap
is used, so that huge number of IPIs are triggered when unmapping
memory. In the test, the throughput of memory writing improves ~5%
compared with misaligned call_single_data, because of faster IPIs.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Huang, Ying <ying.huang@intel.com>
[ Add call_single_data_t and align with size of call_single_data. ]
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Aaron Lu <aaron.lu@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/87bmnqd6lz.fsf@yhuang-mobile.sh.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Since we split the scsi_request out of struct request bsg fails to
provide a reply-buffer for the drivers. This was done via the pointer
for sense-data, that is not preallocated anymore.
Failing to allocate/assign it results in illegal dereferences because
LLDs use this pointer unquestioned.
An example panic on s390x, using the zFCP driver, looks like this (I had
debugging on, otherwise NULL-pointer dereferences wouldn't even panic on
s390x):
Unable to handle kernel pointer dereference in virtual kernel address space
Failing address: 6b6b6b6b6b6b6000 TEID: 6b6b6b6b6b6b6403
Fault in home space mode while using kernel ASCE.
AS:0000000001590007 R3:0000000000000024
Oops: 0038 ilc:2 [#1] PREEMPT SMP DEBUG_PAGEALLOC
Modules linked in: <Long List>
CPU: 2 PID: 0 Comm: swapper/2 Not tainted 4.12.0-bsg-regression+ #3
Hardware name: IBM 2964 N96 702 (z/VM 6.4.0)
task: 0000000065cb0100 task.stack: 0000000065cb4000
Krnl PSW : 0704e00180000000 000003ff801e4156 (zfcp_fc_ct_els_job_handler+0x16/0x58 [zfcp])
R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3 CC:2 PM:0 RI:0 EA:3
Krnl GPRS: 0000000000000001 000000005fa9d0d0 000000005fa9d078 0000000000e16866
000003ff00000290 6b6b6b6b6b6b6b6b 0000000059f78f00 000000000000000f
00000000593a0958 00000000593a0958 0000000060d88800 000000005ddd4c38
0000000058b50100 07000000659cba08 000003ff801e8556 00000000659cb9a8
Krnl Code: 000003ff801e4146: e31020500004 lg %r1,80(%r2)
000003ff801e414c: 58402040 l %r4,64(%r2)
#000003ff801e4150: e35020200004 lg %r5,32(%r2)
>000003ff801e4156: 50405004 st %r4,4(%r5)
000003ff801e415a: e54c50080000 mvhi 8(%r5),0
000003ff801e4160: e33010280012 lt %r3,40(%r1)
000003ff801e4166: a718fffb lhi %r1,-5
000003ff801e416a: 1803 lr %r0,%r3
Call Trace:
([<000003ff801e8556>] zfcp_fsf_req_complete+0x726/0x768 [zfcp])
[<000003ff801ea82a>] zfcp_fsf_reqid_check+0x102/0x180 [zfcp]
[<000003ff801eb980>] zfcp_qdio_int_resp+0x230/0x278 [zfcp]
[<00000000009b91b6>] qdio_kick_handler+0x2ae/0x2c8
[<00000000009b9e3e>] __tiqdio_inbound_processing+0x406/0xc10
[<00000000001684c2>] tasklet_action+0x15a/0x1d8
[<0000000000bd28ec>] __do_softirq+0x3ec/0x848
[<00000000001675a4>] irq_exit+0x74/0xf8
[<000000000010dd6a>] do_IRQ+0xba/0xf0
[<0000000000bd19e8>] io_int_handler+0x104/0x2d4
[<00000000001033b6>] enabled_wait+0xb6/0x188
([<000000000010339e>] enabled_wait+0x9e/0x188)
[<000000000010396a>] arch_cpu_idle+0x32/0x50
[<0000000000bd0112>] default_idle_call+0x52/0x68
[<00000000001cd0fa>] do_idle+0x102/0x188
[<00000000001cd41e>] cpu_startup_entry+0x3e/0x48
[<0000000000118c64>] smp_start_secondary+0x11c/0x130
[<0000000000bd2016>] restart_int_handler+0x62/0x78
[<0000000000000000>] (null)
INFO: lockdep is turned off.
Last Breaking-Event-Address:
[<000003ff801e41d6>] zfcp_fc_ct_job_handler+0x3e/0x48 [zfcp]
Kernel panic - not syncing: Fatal exception in interrupt
This patch moves bsg-lib to allocate and setup struct bsg_job ahead of
time, including the allocation of a buffer for the reply-data.
This means, struct bsg_job is not allocated separately anymore, but as part
of struct request allocation - similar to struct scsi_cmd. Reflect this in
the function names that used to handle creation/destruction of struct
bsg_job.
Reported-by: Steffen Maier <maier@linux.vnet.ibm.com>
Suggested-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Fixes: 82ed4db499 ("block: split scsi_request out of struct request")
Cc: <stable@vger.kernel.org> #4.11+
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We haven't used these in years, but somehow the definitions still
remained. Kill them, and renumber the QUEUE_FLAG_ space. We had
a hole in the beginning of the space, too.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Only used inside the bounce code, and opencoding it makes it more obvious
what is going on.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Useful to verify that things are working the way they should.
Reading the file will return number of kb written with each
write hint. Writing the file will reset the statistics. No care
is taken to ensure that we don't race on updates.
Drivers will write to q->write_hints[] if they handle a given
write hint.
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
No functional changes in this patch, we just use up some holes
in the bio and request structures to define a write hint that
we psas down the stack.
Ensure that we don't merge requests that have different life time
hints assigned to them, and that we inherit the write hint when
cloning a bio.
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull in the fix for shared tags, as it conflicts with the pending
changes in for-4.13/block. We already pulled in v4.12-rc5 to solve
other conflicts or get fixes that went into 4.12, so not a lot
of changes in this merge.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If we have shared tags enabled, then every IO completion will trigger
a full loop of every queue belonging to a tag set, and every hardware
queue for each of those queues, even if nothing needs to be done.
This causes a massive performance regression if you have a lot of
shared devices.
Instead of doing this huge full scan on every IO, add an atomic
counter to the main queue that tracks how many hardware queues have
been marked as needing a restart. With that, we can avoid looking for
restartable queues, if we don't have to.
Max reports that this restores performance. Before this patch, 4K
IOPS was limited to 22-23K IOPS. With the patch, we are running at
950-970K IOPS.
Fixes: 6d8c6c0f97 ("blk-mq: Restart a single queue if tag sets are shared")
Reported-by: Max Gurtovoy <maxg@mellanox.com>
Tested-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Tested-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add a comment above the queue_lockdep_assert_held() macro that
explains the purpose of the q->queue_lock test.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Several block drivers need to initialize the driver-private request
data after having called blk_get_request() and before .prep_rq_fn()
is called, e.g. when submitting a REQ_OP_SCSI_* request. Avoid that
that initialization code has to be repeated after every
blk_get_request() call by adding new callback functions to struct
request_queue and to struct blk_mq_ops.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Instead of declaring the second argument of blk_*_get_request()
as int and passing it to functions that expect an unsigned int,
declare that second argument as unsigned int. Also because of
consistency, rename that second argument from 'rw' into 'op'.
This patch does not change any functionality.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
While the Write Same page currently always is in low-level it is just
as easy and safer to just compare the page and offset directly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
It is required that no dispatch can happen any more once
blk_mq_quiesce_queue() returns, and we don't have such requirement
on APIs of stopping queue.
But blk_mq_quiesce_queue() still may not block/drain dispatch in the
the case of BLK_MQ_S_START_ON_RUN, so use the new introduced flag of
QUEUE_FLAG_QUIESCED and evaluate it inside RCU read-side critical
sections for fixing this issue.
Also blk_mq_quiesce_queue() is implemented via stopping queue, which
limits its uses, and easy to cause race, because any queue restart in
other paths may break blk_mq_quiesce_queue(). With the introduced
flag of QUEUE_FLAG_QUIESCED, we don't need to depend on stopping queue
for quiescing any more.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We usually put blk_mq_*() into include/linux/blk-mq.h, so
move this API into there.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blk_queue_split() is always called with the last arg being q->bio_split,
where 'q' is the first arg.
Also blk_queue_split() sometimes uses the passed-in 'bs' and sometimes uses
q->bio_split.
This is inconsistent and unnecessary. Remove the last arg and always use
q->bio_split inside blk_queue_split()
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Credit-to: Javier González <jg@lightnvm.io> (Noticed that lightnvm was missed)
Reviewed-by: Javier González <javier@cnexlabs.com>
Tested-by: Javier González <javier@cnexlabs.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Avoid that the following complaint is reported:
BUG: sleeping function called from invalid context at kernel/workqueue.c:2790
in_atomic(): 1, irqs_disabled(): 0, pid: 41, name: rcuop/3
1 lock held by rcuop/3/41:
#0: (rcu_callback){......}, at: [<ffffffff8111f9a2>] rcu_nocb_kthread+0x282/0x500
Call Trace:
dump_stack+0x86/0xcf
___might_sleep+0x174/0x260
__might_sleep+0x4a/0x80
flush_work+0x7e/0x2e0
__cancel_work_timer+0x143/0x1c0
cancel_work_sync+0x10/0x20
blk_throtl_exit+0x25/0x60
blkcg_exit_queue+0x35/0x40
blk_release_queue+0x42/0x130
kobject_put+0xa9/0x190
This happens since we invoke callbacks that need to block from the
queue release handler. Fix this by pushing the final release to
a workqueue.
Reported-by: Ross Zwisler <zwisler@gmail.com>
Fixes: commit b425e50492 ("block: Avoid that blk_exit_rl() triggers a use-after-free")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Tested-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Updated changelog
Signed-off-by: Jens Axboe <axboe@fb.com>
Replace bi_error with a new bi_status to allow for a clear conversion.
Note that device mapper overloaded bi_error with a private value, which
we'll have to keep arround at least for now and thus propagate to a
proper blk_status_t value.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently we use nornal Linux errno values in the block layer, and while
we accept any error a few have overloaded magic meanings. This patch
instead introduces a new blk_status_t value that holds block layer specific
status codes and explicitly explains their meaning. Helpers to convert from
and to the previous special meanings are provided for now, but I suspect
we want to get rid of them in the long run - those drivers that have a
errno input (e.g. networking) usually get errnos that don't know about
the special block layer overloads, and similarly returning them to userspace
will usually return somethings that strictly speaking isn't correct
for file system operations, but that's left as an exercise for later.
For now the set of errors is a very limited set that closely corresponds
to the previous overloaded errno values, but there is some low hanging
fruite to improve it.
blk_status_t (ab)uses the sparse __bitwise annotations to allow for sparse
typechecking, so that we can easily catch places passing the wrong values.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
From the context where a SCSI command is submitted it is not always
possible to figure out whether or not the queue the command is
submitted to has struct scsi_request as the first member of its
private data. Hence introduce the flag QUEUE_FLAG_SCSI_PASSTHROUGH.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Don Brace <don.brace@microsemi.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull libnvdimm fixes from Dan Williams:
"Incremental fixes and a small feature addition on top of the main
libnvdimm 4.12 pull request:
- Geert noticed that tinyconfig was bloated by BLOCK selecting DAX.
The size regression is fixed by moving all dax helpers into the
dax-core and only specifying "select DAX" for FS_DAX and
dax-capable drivers. He also asked for clarification of the
NR_DEV_DAX config option which, on closer look, does not need to be
a config option at all. Mike also throws in a DEV_DAX_PMEM fixup
for good measure.
- Ben's attention to detail on -stable patch submissions caught a
case where the recent fixes to arch_copy_from_iter_pmem() missed a
condition where we strand dirty data in the cache. This is tagged
for -stable and will also be included in the rework of the pmem api
to a proposed {memcpy,copy_user}_flushcache() interface for 4.13.
- Vishal adds a feature that missed the initial pull due to pending
review feedback. It allows the kernel to clear media errors when
initializing a BTT (atomic sector update driver) instance on a pmem
namespace.
- Ross noticed that the dax_device + dax_operations conversion broke
__dax_zero_page_range(). The nvdimm unit tests fail to check this
path, but xfstests immediately trips over it. No excuse for missing
this before submitting the 4.12 pull request.
These all pass the nvdimm unit tests and an xfstests spot check. The
set has received a build success notification from the kbuild robot"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
filesystem-dax: fix broken __dax_zero_page_range() conversion
libnvdimm, btt: ensure that initializing metadata clears poison
libnvdimm: add an atomic vs process context flag to rw_bytes
x86, pmem: Fix cache flushing for iovec write < 8 bytes
device-dax: kill NR_DEV_DAX
block, dax: move "select DAX" from BLOCK to FS_DAX
device-dax: Tell kbuild DEV_DAX_PMEM depends on DEV_DAX
For configurations that do not enable DAX filesystems or drivers, do not
require the DAX core to be built.
Given that the 'direct_access' method has been removed from
'block_device_operations', we can also go ahead and remove the
block-related dax helper functions from fs/block_dev.c to
drivers/dax/super.c. This keeps dax details out of the block layer and
lets the DAX core be built as a module in the FS_DAX=n case.
Filesystems need to include dax.h to call bdev_dax_supported().
Cc: linux-xfs@vger.kernel.org
Cc: Jens Axboe <axboe@kernel.dk>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: "Darrick J. Wong" <darrick.wong@oracle.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Jan Kara <jack@suse.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Minwoo Im