The kernel IB stack uses one enumeration for IB speed, which wasn't
explicitly specified in the verbs header file. Add that enum, and use
it all over the code.
The IB speed/width notation is also used by iWARP and IBoE HW drivers,
which use the convention of rate = speed * width to advertise their
port link rate.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Update copyright information in the source files.
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Faisal Latif <Faisal.Latif@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix fast memory registration opcode in local invalidate completion.
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Donald Wood <Donald.E.Wood@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Zero high order word of fast memory registration (FMR) length field.
FMR length field is 32 bits, so high word should always be zero.
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Donald Wood <Donald.E.Wood@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Make sure all exit paths from this function unlock everything.
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Set a reject flag, when sending MPA reject message to inform the peer
that the application has rejected the connection.
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Faisal Latif <Faisal.Latif@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Now we must provide the IP destination address, and a reference has
to be dropped when we're done with the entry.
Signed-off-by: David S. Miller <davem@davemloft.net>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Fix for reset which happens right after sending a terminate message.
Terminate timer is not deleted when the connection is closed.
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Faisal Latif <Faisal.Latif@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Change the PHY clock divisor to make the MDIO clock 2.5MHz, instead of
3.5MHz (which is out of spec).
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Faisal Latif <Faisal.Latif@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
To reflect the fact that a refrence is not obtained to the
resulting neighbour entry.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Roland Dreier <roland@purestorage.com>
Commit f2c31e32b3 ("net: fix NULL dereferences in check_peer_redir()")
forgot to take care of infiniband uses of dst neighbours.
Many thanks to Marc Aurele who provided a nice bug report and feedback.
Reported-by: Marc Aurele La France <tsi@ualberta.ca>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (62 commits)
mlx4_core: Deprecate log_num_vlan module param
IB/mlx4: Don't set VLAN in IBoE WQEs' control segment
IB/mlx4: Enable 4K mtu for IBoE
RDMA/cxgb4: Mark QP in error before disabling the queue in firmware
RDMA/cxgb4: Serialize calls to CQ's comp_handler
RDMA/cxgb3: Serialize calls to CQ's comp_handler
IB/qib: Fix issue with link states and QSFP cables
IB/mlx4: Configure extended active speeds
mlx4_core: Add extended port capabilities support
IB/qib: Hold links until tuning data is available
IB/qib: Clean up checkpatch issue
IB/qib: Remove s_lock around header validation
IB/qib: Precompute timeout jiffies to optimize latency
IB/qib: Use RCU for qpn lookup
IB/qib: Eliminate divide/mod in converting idx to egr buf pointer
IB/qib: Decode path MTU optimization
IB/qib: Optimize RC/UC code by IB operation
IPoIB: Use the right function to do DMA unmap pages
RDMA/cxgb4: Use correct QID in insert_recv_cqe()
RDMA/cxgb4: Make sure flush CQ entries are collected on connection close
...
To ease skb->truesize sanitization, its better to be able to localize
all references to skb frags size.
Define accessors : skb_frag_size() to fetch frag size, and
skb_frag_size_{set|add|sub}() to manipulate it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for Packed and Unaligned (PAU) FPDUs is needed for
interoperability between NES and non-NES nodes. When the NES hardware
detects a PAU frame, it will pass it to the driver to process the
frame. NES driver creates a new frame for each FPDU and forwards it
to the hardware to be sent to its associated qp.
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Faisal Latif <Faisal.Latif@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Print the IP address of the remote host when a critical asynchronous event is
received.
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Faisal Latif <Faisal.Latif@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fixes a crash that occurs during close when error async event is received.
Terminate message is not sent to the remote node if already processing close.
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Faisal Latif <Faisal.Latif@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When I converted some drivers from pci_map_page to skb_frag_dma_map I
neglected to convert PCI_DMA_xDEVICE into DMA_x_DEVICE and
pci_dma_mapping_error into dma_mapping_error.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for Enhanced RDMA Connection Establishment
(draft-ietf-storm-mpa-peer-connect-06), aka MPAv2. Details of draft
can be obtained from:
<http://www.ietf.org/id/draft-ietf-storm-mpa-peer-connect-06.txt>
For backwards compatibility, the MPAv2 enabled driver reverts to MPAv1
if the remote node doesn't support MPAv2.
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Faisal Latif <Faisal.Latif@intel.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add calls to ib_umem_release(), as in the other error-handling code in
nes_reg_user_mr().
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Faisal Latif <faisal.latif@intel.com>
Cc: Roland Dreier <roland@kernel.org>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: linux-rdma@vger.kernel.org
Cc: netdev@vger.kernel.org
Acked-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (26 commits)
IB/qib: Defer HCA error events to tasklet
mlx4_core: Bump the driver version to 1.0
RDMA/cxgb4: Use printk_ratelimited() instead of printk_ratelimit()
IB/mlx4: Support PMA counters for IBoE
IB/mlx4: Use flow counters on IBoE ports
IB/pma: Add include file for IBA performance counters definitions
mlx4_core: Add network flow counters
mlx4_core: Fix location of counter index in QP context struct
mlx4_core: Read extended capabilities into the flags field
mlx4_core: Extend capability flags to 64 bits
IB/mlx4: Generate GID change events in IBoE code
IB/core: Add GID change event
RDMA/cma: Don't allow IPoIB port space for IBoE
RDMA: Allow for NULL .modify_device() and .modify_port() methods
IB/qib: Update active link width
IB/qib: Fix potential deadlock with link down interrupt
IB/qib: Add sysfs interface to read free contexts
IB/mthca: Remove unnecessary read of PCI_CAP_ID_EXP
IB/qib: Remove double define
IB/qib: Remove unnecessary read of PCI_CAP_ID_EXP
...
- unify vlan and nonvlan rx path
- kill nesvnic->vlan_grp and nes_netdev_vlan_rx_register
- allow to turn on/off rx/tx vlan accel via ethtool (set_features)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These methods don't make sense for iWARP devices, so rather than
forcing them to implement stubs, just return -ENOSYS in the core if
the hardware driver doesn't set .modify_device and/or .modify_port.
Signed-off-by: Roland Dreier <roland@purestorage.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/cma: Save PID of ID's owner
RDMA/cma: Add support for netlink statistics export
RDMA/cma: Pass QP type into rdma_create_id()
RDMA: Update exported headers list
RDMA/cma: Export enum cma_state in <rdma/rdma_cm.h>
RDMA/nes: Add a check for strict_strtoul()
RDMA/cxgb3: Don't post zero-byte read if endpoint is going away
RDMA/cxgb4: Use completion objects for event blocking
IB/srp: Fix integer -> pointer cast warnings
IB: Add devnode methods to cm_class and umad_class
IB/mad: Return EPROTONOSUPPORT when an RDMA device lacks the QP required
IB/uverbs: Add devnode method to set path/mode
RDMA/ucma: Add .nodename/.mode to tell userspace where to create device node
RDMA: Add netlink infrastructure
RDMA: Add error handling to ib_core_init()
It should check if strict_strtoul() succeeds before using
'wqm_quanta_value'.
Signed-off-by: Liu Yuan <tailai.ly@taobao.com>
[ Convert to kstrtoul() directly while we're here. - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1446 commits)
macvlan: fix panic if lowerdev in a bond
tg3: Add braces around 5906 workaround.
tg3: Fix NETIF_F_LOOPBACK error
macvlan: remove one synchronize_rcu() call
networking: NET_CLS_ROUTE4 depends on INET
irda: Fix error propagation in ircomm_lmp_connect_response()
irda: Kill set but unused variable 'bytes' in irlan_check_command_param()
irda: Kill set but unused variable 'clen' in ircomm_connect_indication()
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_transport()
be2net: Kill set but unused variable 'req' in lancer_fw_download()
irda: Kill set but unused vars 'saddr' and 'daddr' in irlan_provider_connect_indication()
atl1c: atl1c_resume() is only used when CONFIG_PM_SLEEP is defined.
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_peer().
rxrpc: Kill set but unused variable 'local' in rxrpc_UDP_error_handler()
rxrpc: Kill set but unused variable 'sp' in rxrpc_process_connection()
rxrpc: Kill set but unused variable 'sp' in rxrpc_rotate_tx_window()
pkt_sched: Kill set but unused variable 'protocol' in tc_classify()
isdn: capi: Use pr_debug() instead of ifdefs.
tg3: Update version to 3.119
tg3: Apply rx_discards fix to 5719/5720
...
Fix up trivial conflicts in arch/x86/Kconfig and net/mac80211/agg-tx.c
as per Davem.
The IW_CM_EVENT_STATUS_xxx values were used in only a couple of places;
cma.c uses -Exxx values instead, and so do the amso1100, cxgb3 and cxgb4
drivers -- only nes was using the enum values (with the mild consequence
that all nes connection failures were treated as generic errors rather
than reported as timeouts or rejections).
We can fix this confusion by getting rid of enum iw_cm_event_status and
using a plain int for struct iw_cm_event.status, and converting nes to
use -Exxx as the other iWARP drivers do.
This also gets rid of the warning
drivers/infiniband/core/cma.c: In function 'cma_iw_handler':
drivers/infiniband/core/cma.c:1333:3: warning: case value '4294967185' not in enumerated type 'enum iw_cm_event_status'
drivers/infiniband/core/cma.c:1336:3: warning: case value '4294967186' not in enumerated type 'enum iw_cm_event_status'
drivers/infiniband/core/cma.c:1332:3: warning: case value '4294967192' not in enumerated type 'enum iw_cm_event_status'
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Faisal Latif <faisal.latif@intel.com>
This updates the network drivers so that they don't access the
ethtool_cmd::speed field directly, but use ethtool_cmd_speed()
instead.
For most of the drivers, these changes are purely cosmetic and don't
fix any problem, such as for those 1GbE/10GbE drivers that indirectly
call their own ethtool get_settings()/mii_ethtool_gset(). The changes
are meant to enforce code consistency and provide robustness with
future larger throughputs, at the expense of a few CPU cycles for each
ethtool operation.
All drivers compiled with make allyesconfig ion x86_64 have been
updated.
Tested: make allyesconfig on x86_64 + e1000e/bnx2x work
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1765a57533 ("net: make dev->master general") introduced a
test of an uninitialized netdev. Fix the code so the intended netdev
is tested.
Signed-off-by: Roland Dreier <roland@purestorage.com>
There's no reason to print "NetEffect RNIC driver successfully loaded"
at level KERN_ERR (where it will uglify the console on a quiet boot).
Change it to KERN_INFO.
Signed-off-by: Roland Dreier <roland@purestorage.com>
The idea here is this minimizes the number of places one has to edit
in order to make changes to how flows are defined and used.
Signed-off-by: David S. Miller <davem@davemloft.net>
dev->master is now tightly connected to bonding driver. This patch makes
this pointer more general and ready to be used by others.
- netdev_set_master() - bond specifics moved to new function
netdev_set_bond_master()
- introduced netif_is_bond_slave() to check if device is a bonding slave
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nes_port_ibevent() should not be called when the nes RDMA device is not
registered with the RDMA core. Add missing checks of of_device_registered flag.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
During iw_nes initialization the link status for SFP+ PHY is always
detected as "up" regardless of real state (cable either connected or
disconnected). Add SFP+ PHY specific link status detection to the
iw_nes initialization procedure. Use link status recheck for
netdev_open to detect delayed state updates.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In case of SFP+ PHY, link status check at interrupt processing can
give false results. For proper link status change detection a delayed
recheck is needed to give nes registers time to settle. Add a
periodic link status recheck scheduled at interrupt to detect
potential delayed registers state changes.
Addresses: http://bugs.openfabrics.org/bugzilla/show_bug.cgi?id=2117
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Depending on link state change, IB_EVENT_PORT_ERR or
IB_EVENT_PORT_ACTIVE should be generated when handling MAC interrupts.
Plugging in a cable happens to result in series of interrupts changing
driver's link state a number of times before finally staying at link
up (e.g. link up, link down, link up, link down, ..., link up). To
prevent sending series of redundant IB_EVENT_PORT_ACTIVE and
IB_EVENT_PORT_ERR events, we use a timer to debounce them in
nes_port_ibevent().
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Enable configuring bonds on nes devices by adding missing support for
master net_device to the driver.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (63 commits)
IB/qib: clean up properly if pci_set_consistent_dma_mask() fails
IB/qib: Allow driver to load if PCIe AER fails
IB/qib: Fix uninitialized pointer if CONFIG_PCI_MSI not set
IB/qib: Fix extra log level in qib_early_err()
RDMA/cxgb4: Remove unnecessary KERN_<level> use
RDMA/cxgb3: Remove unnecessary KERN_<level> use
IB/core: Add link layer type information to sysfs
IB/mlx4: Add VLAN support for IBoE
IB/core: Add VLAN support for IBoE
IB/mlx4: Add support for IBoE
mlx4_en: Change multicast promiscuous mode to support IBoE
mlx4_core: Update data structures and constants for IBoE
mlx4_core: Allow protocol drivers to find corresponding interfaces
IB/uverbs: Return link layer type to userspace for query port operation
IB/srp: Sync buffer before posting send
IB/srp: Use list_first_entry()
IB/srp: Reduce number of BUSY conditions
IB/srp: Eliminate two forward declarations
IB/mlx4: Signal node desc changes to SM by using FW to generate trap 144
IB: Replace EXTRA_CFLAGS with ccflags-y
...
We tried very hard to remove all possible dev_hold()/dev_put() pairs in
network stack, using RCU conversions.
There is still an unavoidable device refcount change for every dst we
create/destroy, and this can slow down some workloads (routers or some
app servers, mmap af_packet)
We can switch to a percpu refcount implementation, now dynamic per_cpu
infrastructure is mature. On a 64 cpus machine, this consumes 256 bytes
per device.
On x86, dev_hold(dev) code :
before
lock incl 0x280(%ebx)
after:
movl 0x260(%ebx),%eax
incl fs:(%eax)
Stress bench :
(Sending 160.000.000 UDP frames,
IP route cache disabled, dual E5540 @2.53GHz,
32bit kernel, FIB_TRIE)
Before:
real 1m1.662s
user 0m14.373s
sys 12m55.960s
After:
real 0m51.179s
user 0m15.329s
sys 10m15.942s
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This lets the bonding driver to detect when an interface goes down.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
With commit cd6860eb ("RDMA/nes: Fix hangs on ifdown") we no longer
remove nes interfaces on ifdown. On nes_query_port(), add an
additional check of the netdev queue and report IB_PORT_DOWN if the
queue is not running.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Just a small cleanup. The "passive_state" variable isn't used any
more after commit dae58728dc ("RDMA/nes: Fix double CLOSE event
indication crash")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix:
drivers/infiniband/hw/nes/nes_verbs.c: In function 'nes_alloc_fast_reg_page_list':
drivers/infiniband/hw/nes/nes_verbs.c:477: warning: cast to pointer from integer of different size
drivers/infiniband/hw/nes/nes_verbs.c: In function 'nes_post_send':
drivers/infiniband/hw/nes/nes_verbs.c:3486: warning: cast to pointer from integer of different size
drivers/infiniband/hw/nes/nes_verbs.c:3486: warning: cast to pointer from integer of different size
by printing u64 quantities by casting to unsigned long and long and
using %llx, rather than casting to void* and using %p.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Changing state to CLOSING when FIN is received causes A0 cards to
hang. Fix this by checking for A0 cards in FIN handling.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When the driver receives an AE for FIN received, it closes the
connection without changing the state of the connection in the
hardware to closing. By changing the state to closing, hardware will
do a normal close sequence.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
During a stress testing in a large cluster, multiple close event are
detected and BUG() is hit in the iWARP core. The cause is that the
active node gave up while waiting for an MPA response from the peer
and tried to close the connection by sending RST. The passive node
driver receives the RST but is waiting for MPA response from the user.
When the MPA accept is received, the driver offloads the connection
and sends a CLOSE event. The driver gets an AE indicating RESET
received and also sends a CLOSE event, hitting a BUG().
Fix this by correcting RESET handling and sending CLOSE events.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Setting TX pause param writes to the wrong register location causing
the adapter to hang. Correct the define used to write the reigster.
Addresses: https://bugs.openfabrics.org/show_bug.cgi?id=2116
Reported-by: Shiri Franchi <shirif@voltaire.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (42 commits)
IB/qib: Add missing <linux/slab.h> include
IB/ehca: Drop unnecessary NULL test
RDMA/nes: Fix confusing if statement indentation
IB/ehca: Init irq tasklet before irq can happen
RDMA/nes: Fix misindented code
RDMA/nes: Fix showing wqm_quanta
RDMA/nes: Get rid of "set but not used" variables
RDMA/nes: Read firmware version from correct place
IB/srp: Export req_lim via sysfs
IB/srp: Make receive buffer handling more robust
IB/srp: Use print_hex_dump()
IB: Rename RAW_ETY to RAW_ETHERTYPE
RDMA/nes: Fix two sparse warnings
RDMA/cxgb3: Make needlessly global iwch_l2t_send() static
IB/iser: Make needlessly global iser_alloc_rx_descriptors() static
RDMA/cxgb4: Add timeouts when waiting for FW responses
IB/qib: Fix race between qib_error_qp() and receive packet processing
IB/qib: Limit the number of packets processed per interrupt
IB/qib: Allow writes to the diag_counters to be able to clear them
IB/qib: Set cfgctxts to number of CPUs by default
...
Fix confusing indentation that makes a statement look as if it's part of
an if statement when in fact it isn't.
Reported-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Simple changes to fix warnings:
CHECK drivers/infiniband/hw/nes/nes_verbs.c
nes_verbs.c:1944:45: warning: Using plain integer as NULL pointer
nes_verbs.c:1944:48: warning: Using plain integer as NULL pointer
CHECK drivers/infiniband/hw/nes/nes_cm.c
nes_cm.c:2645:43: warning: mixing different enum types
nes_cm.c:2645:43: int enum iw_cm_event_type versus
nes_cm.c:2645:43: int enum iw_cm_event_status
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Acked-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When ib_unregister_device() is called from netdev stop during ifdown,
it sometimes hangs. Changes made to indicate port_err to ib_dispatch_event()
during netdev stop and port_active during netdev open. The
ib_unregister_device() is only called during remove of the module.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Read and print eeprom version and save it off for later use.
Also delete a tab.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change code like
x = expr(++x)
that assigns to x twice without a sequence point in between to the
intended (and well-defined)
x = expr(x + 1)
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Following commit 1437ce3983 "ethtool:
Change ethtool_op_set_flags to validate flags", ethtool_op_set_flags
takes a third parameter and cannot be used directly as an
implementation of ethtool_ops::set_flags.
Changes nes and ipoib driver to pass in the appropriate value.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove useless union keyword in rtable, rt6_info and dn_route.
Since there is only one member in a union, the union keyword isn't useful.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/nes: Fix incorrect unlock in nes_process_mac_intr()
RDMA/nes: Async event for closed QP causes crash
RDMA/nes: Have ethtool read hardware registers for rx/tx stats
RDMA/cxgb4: Only insert sq qid in lookup table
RDMA/cxgb4: Support IB_WR_READ_WITH_INV opcode
RDMA/cxgb4: Set fence flag for inv-local-stag work requests
RDMA/cxgb4: Update some HW limits
RDMA/cxgb4: Don't limit fastreg page list depth
RDMA/cxgb4: Return proper errors in fastreg mr/pbl allocation
RDMA/cxgb4: Fix overflow bug in CQ arm
RDMA/cxgb4: Optimize CQ overflow detection
RDMA/cxgb4: CQ size must be IQ size - 2
RDMA/cxgb4: Register RDMA provider based on LLD state_change events
RDMA/cxgb4: Detach from the LLD after unregistering RDMA device
IB/ipath: Remove support for QLogic PCIe QLE devices
IB/qib: Add new qib driver for QLogic PCIe InfiniBand adapters
IB/mad: Make needlessly global mad_sendq_size/mad_recvq_size static
IB/core: Allow device-specific per-port sysfs files
mlx4_core: Clean up mlx4_alloc_icm() a bit
mlx4_core: Fix possible chunk sg list overflow in mlx4_alloc_icm()
Commit ce6e74f2 ("RDMA/nes: Make nesadapter->phy_lock usage
consistent") introduced a problem where phy_lock was only unlocked
within an if statement and so nes_process_mac_intr() could return with
phy_lock still held. Fix this.
This was discovered because of the sparse warning:
drivers/infiniband/hw/nes/nes_hw.c:2643:9: warning: context imbalance in 'nes_process_mac_intr' - different lock contexts for basic block
Reported-by: Roland Dreier <rdreier@cisco.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Under abnormal termination, modify_qp() closes the QP, and async event
(AE) handling also attempts to close the same QP, causing a crash.
Fix this by checking the state of the QP before processing the AE.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Enhance ethtool to read hardware registers for rcv/tx error stats.
Also add support for free pbl resources. Remove cq depth stats, which
are not used.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a new parameter to ib_register_device() so that low-level device
drivers can pass in a pointer to a callback function that will be
called for each port that is registered in sysfs. This allows
low-level device drivers to create files in
/sys/class/infiniband/<hca>/ports/<N>/
without having to poke through the internals of the RDMA sysfs handling.
There is no need for an unregister function since the kobject
reference will go to zero when ib_unregister_device() is called.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
qlcnic: adding co maintainer
ixgbe: add support for active DA cables
ixgbe: dcb, do not tag tc_prio_control frames
ixgbe: fix ixgbe_tx_is_paused logic
ixgbe: always enable vlan strip/insert when DCB is enabled
ixgbe: remove some redundant code in setting FCoE FIP filter
ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
ixgbe: fix header len when unsplit packet overflows to data buffer
ipv6: Never schedule DAD timer on dead address
ipv6: Use POSTDAD state
ipv6: Use state_lock to protect ifa state
ipv6: Replace inet6_ifaddr->dead with state
cxgb4: notify upper drivers if the device is already up when they load
cxgb4: keep interrupts available when the ports are brought down
cxgb4: fix initial addition of MAC address
cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
cnic: Convert cnic_local_flags to atomic ops.
can: Fix SJA1000 command register writes on SMP systems
bridge: fix build for CONFIG_SYSFS disabled
ARCNET: Limit com20020 PCI ID matches for SOHARD cards
...
Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).
Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c
This allows the compiler to do a bit better; on my x86-64 build:
add/remove: 0/2 grow/shrink: 1/0 up/down: 2288/-2365 (-77)
function old new delta
nes_init_phy 273 2561 +2288
nes_init_1g_phy 469 - -469
nes_init_2025_phy 1896 - -1896
Signed-off-by: Roland Dreier <rolandd@cisco.com>
nes_{read,write}_1G_phy_reg() are using phy_lock while
nes_{read,write}_10G_phy_reg() leave that to the caller.
Remove phy_lock from 1G routines and leave the locking to the caller.
Add additional phy_lock calls around 1G read/write.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Check correct variable for allocation failure
RDMA/nes: Correct cap.max_inline_data assignment in nes_query_qp()
RDMA/cm: Set num_paths when manually assigning path records
IB/cm: Fix device_create() return value check
cap.max_inline_data is incorrectly set in init_attr instead of attr.
Set it in attr so subsequent init_attr.cap assignment will get the
correct value.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Converts the list and the core manipulating with it to be the same as uc_list.
+uses two functions for adding/removing mc address (normal and "global"
variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Commit 09124e19 ("RDMA/nes: Add support for KR device id 0x0110") took
out too much code and broke CX4 link detection in back-to-back
configuration. Put back the code that does the link check.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Clear the stall bit to drop any incoming packets while destroying NIC
QP. This will prevent a chip resource leak.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Set assume_aligned_header bit in QP context as requested by hardware group.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (48 commits)
IB/srp: Clean up error path in srp_create_target_ib()
IB/srp: Split send and recieve CQs to reduce number of interrupts
RDMA/nes: Add support for KR device id 0x0110
IB/uverbs: Use anon_inodes instead of private infinibandeventfs
IB/core: Fix and clean up ib_ud_header_init()
RDMA/cxgb3: Mark RDMA device with CXIO_ERROR_FATAL when removing
RDMA/cxgb3: Don't allocate the SW queue for user mode CQs
RDMA/cxgb3: Increase the max CQ depth
RDMA/cxgb3: Doorbell overflow avoidance and recovery
IB/core: Pack struct ib_device a little tighter
IB/ucm: Clean whitespace errors
IB/ucm: Increase maximum devices supported
IB/ucm: Use stack variable 'base' in ib_ucm_add_one
IB/ucm: Use stack variable 'devnum' in ib_ucm_add_one
IB/umad: Clean whitespace
IB/umad: Increase maximum devices supported
IB/umad: Use stack variable 'base' in ib_umad_init_port
IB/umad: Use stack variable 'devnum' in ib_umad_init_port
IB/umad: Remove port_table[]
IB/umad: Convert *cdev to cdev in struct ib_umad_port
...
Due to the loop complexicity in nes_nic.c, I'm using char* to copy mc addresses
to it.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for KR device id 0x0110. While at it, cleanup
nes_init_phy() by splitting it into nes_init_1g_phy() and
nes_init_2025_phy().
Remove support for NES_PHY_TYPE_IRIS, which was used on an XFP board
that was only manufactured in small quantities and given out for evals
in even smaller quantities.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change the nes driver to return -ENOMEM on SQ/RQ overflow to match the
return code of other RDMA HW drivers (e.g cxgb3, ehca, mlx4, mthca).
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Acked-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There is a double disconnect during AE processing, causing crashes.
While fixing the crash, also simplify the AE handling code.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When a listener is destroyed and there is an MPA response pending for
loopback connection, the active side cm_node gets destroyed twice:
once in cm_event_connect_error() and again in nes_accept()/nes_reject().
Increment the cm_node's refcount so it's not destroyed by
cm_event_connect_error().
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
After running long iterative MPI tests, sometimes ethtool reports a
"CM Destroy Listener" count more than the "CM Create Listener" count.
This inconsistency is fixed by making counter variables atomic.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch replaces dev->mc_count in all drivers (hopefully I didn't miss
anything). Used spatch and did small tweaks and conding style changes when
it was suitable.
Jirka
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the remote node's ethernet address changes, the connection keeps
trying to connect using the old address. The connection wil continue
failing until the driver is unloaded and loaded again (eiter reboot or
rmmod). Fix this by checking that the NIC has the correct address
before starting a connection.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A FIN that is received during an MPA start up sequence causes a
timeout in iwcm.c. The connection has not been completely closed so
the iwcm code is waiting for resources to be cleaned up. This closes
the connection so everything cleans up correctly.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We fail when creating many qps as kmap() fails for sq_vbase.
Fix this by doing kunmap() as soon as we are done with sq_vbase.
We do kunmap() in one of the locations below:
(1) nes_destroy_qp()
(2) nes_accept()
(3) nes_connect_event
We keep a flag to avoid multiple calls to kunmap().
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
STags are generated randomly but the driver does not correctly prevent
a zero STag. Using STag zero is privileged and causes a user space
application to fail. This change prevents the driver from trying to
allocate a zero STag.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
While running a Xansation test, an active side node crashed. The
problem started on the passive side, which generated an STtag that was
0. The passive side sent a TERMINATE instead of an MPA REJECT msg.
The active side, receives TERMINATE and sends connect_err() and set
the cm_node state to CLOSED. The passive side sends FIN + ACK after
TERMINATE. Active side ends up in handle_ack_pkt() and send_reset().
send_reset() consumes 1 cm_node's ref_count. Because the cm_node is
in CLOSED state, which means that cm_node will be destroyed after
completion of the connect_err() indication, CM will crash after
send_reset().
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When the listener is destroyed for a loopback connection, the listener
node gets a reset event. This causes a crash as the listener is not
expecting a reset event. Code review of cm_event_reset() during
debugging showed the cm_id ref count is incremented after calling its
event handler and not before.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
While running IMP_EXT's window test, we saw a crash in nes_accept().
Here is the sequence of what happened:
(1) In MVAPICH2, connect request is received for port #0.
FIX: Add a nes_connect() check to make sure local or remote tcp port
is not 0.
(2) Remote node's (passive) TCP stack sends a reset when it gets a
connect request because of port = 0. Active side set the connect
error to IW_CM_EVENT_STATUS_REJECTED when it received the RST from
remote node.
FIX: The corect error code is -ECONNRESET.
(3) Wrong error code of IW_CM_EVENT_STATUS_REJECTED causes the core to
destroy its listener ports. Here there are connections that may
have sent an MPA request up and waiting for accept or reject. But
the listener and its cm_nodes have been freed already causing the
crash noticed.
FIX: The cm_node is freed only if its state is not
NES_CM_STATE_MPAREQ_RCVD. If cm_node's state is
NES_CM_STATE_MPAREQ_RCVD then its new state is set to
NES_CM_STATE_LISTENER_DESTROYED and it is not freed. When
nes_accept() or nes_reject() is received, its state is checked
for NES_CM_STATE_LISTENER_DESTROYED and in this case the cm_node
is freed and error is returned.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
During testing of REJECT connection error handling, we saw that the
cm_id resources are not released. When the retransmit timer expires,
we need to send a reset message to remote node before issuing the
ABORTED event.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
During Xansation testing, we saw that error handling of MPA frame
msg/response is not handled properly.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The ORD size needs updating as we are supporting more inbound READ
resources per connection.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change MAX_CM_BUFFER for MPA frames to be conformant to RFC 5044:
we need 512 + 20 instead of 512.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The size argument to ioremap_nocache should be the size of desired
information, not the pointer to it.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@expression@
expression *x;
@@
x =
<+...
*sizeof(x)
...+>// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Update copyright from Intel-NE, Inc. to Intel Corporation. Use proper
branding string in Kconfig and simplify description.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a check to nes_create_cq() to return -EINVAL if creating a CQ with
depth > max_cqe (32766).
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add IB_SINGAL_ALL_WR support as an iWARP extension. If set, make sure
all WR for the QP are signalled. Consolidate flags used in nesqp
structure.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add additional PHY uC status check in case PHY firmware is not running
properly with heartbeat. Add a hard PHY reset if uC status is 0x0
after initial reset.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for IB_WR_SEND_WITH_INV, IB_WR_RDMA_READ_WITH_INV
and IB_WR_LOCAL_INV.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
On error, set bad_wr in nes_post_recv(). Stop processing ib_wr queue
when an error is detected.
Signed-off-by: Frank Zago <fzago@systemfabricworks.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
On error, set bad_wr in nes_post_send(). Stop processing ib_wr queue
when an error is detected.
Signed-off-by: Frank Zago <fzago@systemfabricworks.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
These string query operations were supposed to be replaced by the
generic get_sset_count() starting in 2007. Convert the remaining
implementations.
Also remove calls to these operations to initialise drvinfo->n_stats.
The ethtool core code already does that.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Don't turn on carrier for a non-active port
IB/mthca: Fix access to freed memory in catastrophic event handling
mlx4_core: Pass cache line size to device FW
RDMA/nes: Remove duplicate .ndo_set_mac_address field initialization
IB/mad: Fix lock-lock-timer deadlock in RMPP code
The definition of nes_netdev_ops has initializations of a local function
and eth_mac_addr for its ndo_set_mac_address field. This change uses only
the local function.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier I, s, fld;
position p0,p;
expression E;
@@
struct I s =@p0 { ... .fld@p = E, ...};
@s@
identifier I, s, r.fld;
position r.p0,p;
expression E;
@@
struct I s =@p0 { ... .fld@p = E, ...};
@script:python@
p0 << r.p0;
fld << r.fld;
ps << s.p;
pr << r.p;
@@
if int(ps[0].line)!=int(pr[0].line) or int(ps[0].column)!=int(pr[0].column):
cocci.print_main(fld,p0)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1623 commits)
netxen: update copyright
netxen: fix tx timeout recovery
netxen: fix file firmware leak
netxen: improve pci memory access
netxen: change firmware write size
tg3: Fix return ring size breakage
netxen: build fix for INET=n
cdc-phonet: autoconfigure Phonet address
Phonet: back-end for autoconfigured addresses
Phonet: fix netlink address dump error handling
ipv6: Add IFA_F_DADFAILED flag
net: Add DEVTYPE support for Ethernet based devices
mv643xx_eth.c: remove unused txq_set_wrr()
ucc_geth: Fix hangs after switching from full to half duplex
ucc_geth: Rearrange some code to avoid forward declarations
phy/marvell: Make non-aneg speed/duplex forcing work for 88E1111 PHYs
drivers/net/phy: introduce missing kfree
drivers/net/wan: introduce missing kfree
net: force bridge module(s) to be GPL
Subject: [PATCH] appletalk: Fix skb leak when ipddp interface is not loaded
...
Fixed up trivial conflicts:
- arch/x86/include/asm/socket.h
converted to <asm-generic/socket.h> in the x86 tree. The generic
header has the same new #define's, so that works out fine.
- drivers/net/tun.c
fix conflict between 89f56d1e9 ("tun: reuse struct sock fields") that
switched over to using 'tun->socket.sk' instead of the redundantly
available (and thus removed) 'tun->sk', and 2b980dbd ("lsm: Add hooks
to the TUN driver") which added a new 'tun->sk' use.
Noted in 'next' by Stephen Rothwell.
Old query_port code reports static MTU and link state values.
Instead, map actual MTU to next largest IB_MTU_* constant and
correctly report link state.
Cc: Steve Wise <swise@opengridcomputing.com>
Reported-by: Jeff Squyres <jsquyres@cisco.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The disconn routine has been reworked to acoomodate the terminate and
flushing changes. The routine has been reorganized to make all the
decisions at the start then it performs all the required operations.
This simplified the lock handling and is easier to follow.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use the flush status to fill in cqe status when a specific error has
been identified. Subsequent flushed completions still use the flushed
value.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When a flush request is given to the hw, it will place one cqe marked
as flushed (unless there is nothing to flush). An application that is
waiting for all wqe's to complete will be left hanging. This modifies
poll_cq to return the correct number of flushes for the pending
elements on the wq.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When an asynchronous event occurs that requires a terminate, it is
sometimes possible to identify the wqe in error. This change uses
flush to get this information to the poll routine. The flush
operation puts the status into the cqe. If this information is not
available, it continues to use the more generic flush code as before.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Implement the sending and receiving of Terminate packets.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
CQ errors are not being handled correctly. Put in the the upcall for
CQ errors.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When a QP is destroyed, unprocessed CQ entries could still reference
the QP. This change zeroes the context value at QP destroy time. By
skipping over cqe's with a zero context, poll_cq no longer processes a
cqe for a destroyed QP.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The routine to allocate a cqp request is not called from process
context code. Since it is not OK to sleep, it needs to use GFP_ATOMIC
not GFP_KERNEL.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The code currently has a work structure in the QP. This requires a
lock and a pending flag to ensure there is never more than one request
active. When two events happen quickly (such as FIN and LLP CLOSE),
it causes unnecessary timeouts since the second one is dropped.
This fix allocates memory for the work request so the second one can
be queued. A lock is removed since it is no longer needed.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
During termination, it is possible for the refcnt to go to zero while
the worker thread is posting events upward. This fix increments the
refcnt before the request is passed to the worker thread. The thread
decrements the refcnt when the request is completed.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Neil Horman <nhorman@txudriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to put ethtool_ops in data, they should be const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During cluster testing, one QP was not closed, as FIN is not handled
properly when its rexmit count expires or in some cases when RST is is
received after sending FIN. The reason is that the cm_id does not get
decremented under these conditions.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In nes_query_device(), max_qp_init_rd_atom is incorrectly set to
max_qp_wr. This was found when a test application had a dapl async
event error.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
With a postfix increment, i is incremented one past 10K/5K before the
loop ends, so the error messages will be displayed too soon if the
test succeeds on the last iteration. Fix the comparisons to be >
instead of >=.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If reg_phys_mem() fails, we need to free memory allocated for MPA
frame with private data before returning the error. Also move
nes_add_ref() after the reg_phys_mem() is successful.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Running large cluster setup, we are hanging after many hours of
testing. Fixing this required going over the code and making sure the
rexmit entry was properly removed based on the cm_node's state and
packet received. Also when receiving a FIN packet, check seq# and
make sure there were no errors before calling handle_fin().
Following are the changes done in nes_cm.c:
* handle_ack_pkt() needs to return error value, so in case of error,
handle_fin() is not called. Some cleanup done while going over the code.
* handle_rst_pkt(), handling of cm_node's NES_CM_STATE_LAST_ACK is missing.
* process_packet(), in case of FIN only packet is received, call
check_seq() before processing.
* in handle_fin_pkt(), we are calling cleanup_retrans_entry() for all
conditions, even if the packets need to be dropped.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Under heavy load with large cluster testing, it may take longer to
receive a response to MPA requests. Change the driver to wait longer
after each rexmit to max time value.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
check_seq() was not checking if the seq#s have wrapped. Fix it.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Roland Dreier