This reverts commit 8e326289e3.
This patch results in unnecessary netlink notification when one
tries to delete a neigh entry already in NUD_FAILED state. Found
this with a buggy app that tries to delete a NUD_FAILED entry
repeatedly. While the notification issue can be fixed with more
checks, adding more complexity here seems unnecessary. Also,
recent tests with other changes in the neighbour code have
shown that the INCOMPLETE and PROBE checks are good enough for
the original issue.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The loop wants to skip previously dumped addresses, so loops until
current index >= saved index. If the message fills it wants to save
the index for the next address to dump - ie., the one that did not
fit in the current message.
Currently, it is incrementing the index counter before comparing to the
saved index, and then the saved index is off by 1 - it assumes the
current address is going to fit in the message.
Change the index handling to increment only after a succesful dump.
Fixes: 502a2ffd73 ("ipv6: convert idev_list to list macros")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We've been getting checksum errors involving small UDP packets, usually
59B packets with 1 extra non-zero padding byte. netdev_rx_csum_fault()
has been complaining that HW is providing bad checksums. Turns out the
problem is in pskb_trim_rcsum_slow(), introduced in commit 88078d98d1
("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends").
The source of the problem is that when the bytes we are trimming start
at an odd address, as in the case of the 1 padding byte above,
skb_checksum() returns a byte-swapped value. We cannot just combine this
with skb->csum using csum_sub(). We need to use csum_block_sub() here
that takes into account the parity of the start address and handles the
swapping.
Matches existing code in __skb_postpull_rcsum() and esp_remove_trailer().
Fixes: 88078d98d1 ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends")
Signed-off-by: Dimitris Michailidis <dmichail@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 6fe9487892.
It is causing more serious regressions than the RCU warning
it is fixing.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 058214a4d1 ("ip6_tun: Add infrastructure for doing
encapsulation") added the ip6_tnl_encap() call in ip6_tnl_xmit(), before
the call to ipv6_push_frag_opts() to append the IPv6 Tunnel Encapsulation
Limit option (option 4, RFC 2473, par. 5.1) to the outer IPv6 header.
As long as the option didn't actually end up in generated packets, this
wasn't an issue. Then commit 89a23c8b52 ("ip6_tunnel: Fix missing tunnel
encapsulation limit option") fixed sending of this option, and the
resulting layout, e.g. for FoU, is:
.-------------------.------------.----------.-------------------.----- - -
| Outer IPv6 Header | UDP header | Option 4 | Inner IPv6 Header | Payload
'-------------------'------------'----------'-------------------'----- - -
Needless to say, FoU and GUE (at least) won't work over IPv6. The option
is appended by default, and I couldn't find a way to disable it with the
current iproute2.
Turn this into a more reasonable:
.-------------------.----------.------------.-------------------.----- - -
| Outer IPv6 Header | Option 4 | UDP header | Inner IPv6 Header | Payload
'-------------------'----------'------------'-------------------'----- - -
With this, and with 84dad55951 ("udp6: fix encap return code for
resubmitting"), FoU and GUE work again over IPv6.
Fixes: 058214a4d1 ("ip6_tun: Add infrastructure for doing encapsulation")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We initialize a struct tipc_event allocated on the kernel stack to
zero to avert info leak to user space.
Reported-by: syzbot+057458894bc8cada4dee@syzkaller.appspotmail.com
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ethtool_ioctl(), the ioctl command 'ethcmd' is checked through a switch
statement to see whether it is necessary to pre-process the ethtool
structure, because, as mentioned in the comment, the structure
ethtool_rxnfc is defined with padding. If yes, a user-space buffer 'rxnfc'
is allocated through compat_alloc_user_space(). One thing to note here is
that, if 'ethcmd' is ETHTOOL_GRXCLSRLALL, the size of the buffer 'rxnfc' is
partially determined by 'rule_cnt', which is actually acquired from the
user-space buffer 'compat_rxnfc', i.e., 'compat_rxnfc->rule_cnt', through
get_user(). After 'rxnfc' is allocated, the data in the original user-space
buffer 'compat_rxnfc' is then copied to 'rxnfc' through copy_in_user(),
including the 'rule_cnt' field. However, after this copy, no check is
re-enforced on 'rxnfc->rule_cnt'. So it is possible that a malicious user
race to change the value in the 'compat_rxnfc->rule_cnt' between these two
copies. Through this way, the attacker can bypass the previous check on
'rule_cnt' and inject malicious data. This can cause undefined behavior of
the kernel and introduce potential security risk.
This patch avoids the above issue via copying the value acquired by
get_user() to 'rxnfc->rule_cn', if 'ethcmd' is ETHTOOL_GRXCLSRLALL.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dumping classes by parent, kernel would return classes twice:
| # tc qdisc add dev lo root prio
| # tc class show dev lo
| class prio 8001:1 parent 8001:
| class prio 8001:2 parent 8001:
| class prio 8001:3 parent 8001:
| # tc class show dev lo parent 8001:
| class prio 8001:1 parent 8001:
| class prio 8001:2 parent 8001:
| class prio 8001:3 parent 8001:
| class prio 8001:1 parent 8001:
| class prio 8001:2 parent 8001:
| class prio 8001:3 parent 8001:
This comes from qdisc_match_from_root() potentially returning the root
qdisc itself if its handle matched. Though in that case, root's classes
were already dumped a few lines above.
Fixes: cb395b2010 ("net: sched: optimize class dumps")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2018-10-18
1) Free the xfrm interface gro_cells when deleting the
interface, otherwise we leak it. From Li RongQing.
2) net/core/flow.c does not exist anymore, so remove it
from the MAINTAINERS file.
3) Fix a slab-out-of-bounds in _decode_session6.
From Alexei Starovoitov.
4) Fix RCU protection when policies inserted into
thei bydst lists. From Florian Westphal.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If the skb space ends in an unresolved entry while dumping we'll miss
some unresolved entries. The reason is due to zeroing the entry counter
between dumping resolved and unresolved mfc entries. We should just
keep counting until the whole table is dumped and zero when we move to
the next as we have a separate table counter.
Reported-by: Colin Ian King <colin.king@canonical.com>
Fixes: 8fb472c09b ("ipmr: improve hash scalability")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit eb63f2964d ("udp6: add missing checks on edumux packet
processing") used the same return code convention of the ipv4 counterpart,
but ipv6 uses the opposite one: positive values means resubmit.
This change addresses the issue, using positive return value for
resubmitting. Also update the related comment, which was broken, too.
Fixes: eb63f2964d ("udp6: add missing checks on edumux packet processing")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sctp_wait_for_connect is called to wait for connect ready
for sp->strm_interleave in sctp_sendmsg_to_asoc, a panic could
be triggered if cpu is scheduled out and the new asoc is freed
elsewhere, as it will return err and later the asoc gets freed
again in sctp_sendmsg.
[ 285.840764] list_del corruption, ffff9f0f7b284078->next is LIST_POISON1 (dead000000000100)
[ 285.843590] WARNING: CPU: 1 PID: 8861 at lib/list_debug.c:47 __list_del_entry_valid+0x50/0xa0
[ 285.846193] Kernel panic - not syncing: panic_on_warn set ...
[ 285.846193]
[ 285.848206] CPU: 1 PID: 8861 Comm: sctp_ndata Kdump: loaded Not tainted 4.19.0-rc7.label #584
[ 285.850559] Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
[ 285.852164] Call Trace:
...
[ 285.872210] ? __list_del_entry_valid+0x50/0xa0
[ 285.872894] sctp_association_free+0x42/0x2d0 [sctp]
[ 285.873612] sctp_sendmsg+0x5a4/0x6b0 [sctp]
[ 285.874236] sock_sendmsg+0x30/0x40
[ 285.874741] ___sys_sendmsg+0x27a/0x290
[ 285.875304] ? __switch_to_asm+0x34/0x70
[ 285.875872] ? __switch_to_asm+0x40/0x70
[ 285.876438] ? ptep_set_access_flags+0x2a/0x30
[ 285.877083] ? do_wp_page+0x151/0x540
[ 285.877614] __sys_sendmsg+0x58/0xa0
[ 285.878138] do_syscall_64+0x55/0x180
[ 285.878669] entry_SYSCALL_64_after_hwframe+0x44/0xa9
This is a similar issue with the one fixed in Commit ca3af4dd28
("sctp: do not free asoc when it is already dead in sctp_sendmsg").
But this one can't be fixed by returning -ESRCH for the dead asoc
in sctp_wait_for_connect, as it will break sctp_connect's return
value to users.
This patch is to simply set err to -ESRCH before it returns to
sctp_sendmsg when any err is returned by sctp_wait_for_connect
for sp->strm_interleave, so that no asoc would be freed due to
this.
When users see this error, they will know the packet hasn't been
sent. And it also makes sense to not free asoc because waiting
connect fails, like the second call for sctp_wait_for_connect in
sctp_sendmsg_to_asoc.
Fixes: 668c9beb90 ("sctp: implement assign_number for sctp_stream_interleave")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reported an use-after-free involving sctp_id2asoc. Dmitry Vyukov
helped to root cause it and it is because of reading the asoc after it
was freed:
CPU 1 CPU 2
(working on socket 1) (working on socket 2)
sctp_association_destroy
sctp_id2asoc
spin lock
grab the asoc from idr
spin unlock
spin lock
remove asoc from idr
spin unlock
free(asoc)
if asoc->base.sk != sk ... [*]
This can only be hit if trying to fetch asocs from different sockets. As
we have a single IDR for all asocs, in all SCTP sockets, their id is
unique on the system. An application can try to send stuff on an id
that matches on another socket, and the if in [*] will protect from such
usage. But it didn't consider that as that asoc may belong to another
socket, it may be freed in parallel (read: under another socket lock).
We fix it by moving the checks in [*] into the protected region. This
fixes it because the asoc cannot be freed while the lock is held.
Reported-by: syzbot+c7dd55d7aec49d48e49a@syzkaller.appspotmail.com
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pid_task() dereferences rcu protected tasks array.
But there is no rcu_read_lock() in shutdown_umh() routine so that
rcu_read_lock() is needed.
get_pid_task() is wrapper function of pid_task. it holds rcu_read_lock()
then calls pid_task(). if task isn't NULL, it increases reference count
of task.
test commands:
%modprobe bpfilter
%modprobe -rv bpfilter
splat looks like:
[15102.030932] =============================
[15102.030957] WARNING: suspicious RCU usage
[15102.030985] 4.19.0-rc7+ #21 Not tainted
[15102.031010] -----------------------------
[15102.031038] kernel/pid.c:330 suspicious rcu_dereference_check() usage!
[15102.031063]
other info that might help us debug this:
[15102.031332]
rcu_scheduler_active = 2, debug_locks = 1
[15102.031363] 1 lock held by modprobe/1570:
[15102.031389] #0: 00000000580ef2b0 (bpfilter_lock){+.+.}, at: stop_umh+0x13/0x52 [bpfilter]
[15102.031552]
stack backtrace:
[15102.031583] CPU: 1 PID: 1570 Comm: modprobe Not tainted 4.19.0-rc7+ #21
[15102.031607] Hardware name: To be filled by O.E.M. To be filled by O.E.M./Aptio CRB, BIOS 5.6.5 07/08/2015
[15102.031628] Call Trace:
[15102.031676] dump_stack+0xc9/0x16b
[15102.031723] ? show_regs_print_info+0x5/0x5
[15102.031801] ? lockdep_rcu_suspicious+0x117/0x160
[15102.031855] pid_task+0x134/0x160
[15102.031900] ? find_vpid+0xf0/0xf0
[15102.032017] shutdown_umh.constprop.1+0x1e/0x53 [bpfilter]
[15102.032055] stop_umh+0x46/0x52 [bpfilter]
[15102.032092] __x64_sys_delete_module+0x47e/0x570
[ ... ]
Fixes: d2ba09c17a ("net: add skeleton of bpfilter kernel module")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to rfc7496 section 4.3 or 4.4:
sprstat_policy: This parameter indicates for which PR-SCTP policy
the user wants the information. It is an error to use
SCTP_PR_SCTP_NONE in sprstat_policy. If SCTP_PR_SCTP_ALL is used,
the counters provided are aggregated over all supported policies.
We change to dump pr_assoc and pr_stream all status by SCTP_PR_SCTP_ALL
instead, and return error for SCTP_PR_SCTP_NONE, as it also said "It is
an error to use SCTP_PR_SCTP_NONE in sprstat_policy. "
Fixes: 826d253d57 ("sctp: add SCTP_PR_ASSOC_STATUS on sctp sockopt")
Fixes: d229d48d18 ("sctp: add SCTP_PR_STREAM_STATUS sockopt for prsctp")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a missing call to rxrpc_put_peer() on the main path through the
rxrpc_error_report() function. This manifests itself as a ref leak
whenever an ICMP packet or other error comes in.
In commit f334430316, the hand-off of the ref to a work item was removed
and was not replaced with a put.
Fixes: f334430316 ("rxrpc: Fix error distribution")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Other than asoc pmtu sync from all transports, sctp_assoc_sync_pmtu
is also processing transport pmtu_pending by icmp packets. But it's
meaningless to use sctp_dst_mtu(t->dst) as new pmtu for a transport.
The right pmtu value should come from the icmp packet, and it would
be saved into transport->mtu_info in this patch and used later when
the pmtu sync happens in sctp_sendmsg_to_asoc or sctp_packet_config.
Besides, without this patch, as pmtu can only be updated correctly
when receiving a icmp packet and no place is holding sock lock, it
will take long time if the sock is busy with sending packets.
Note that it doesn't process transport->mtu_info in .release_cb(),
as there is no enough information for pmtu update, like for which
asoc or transport. It is not worth traversing all asocs to check
pmtu_pending. So unlike tcp, sctp does this in tx path, for which
mtu_info needs to be atomic_t.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The binding table's 'cluster_scope' list is rcu protected to handle
races between threads changing the list and those traversing the list at
the same moment. We have now found that the function named_distribute()
uses the regular list_for_each() macro to traverse the said list.
Likewise, the function tipc_named_withdraw() is removing items from the
same list using the regular list_del() call. When these two functions
execute in parallel we see occasional crashes.
This commit fixes this by adding the missing _rcu() suffixes.
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The udpv6_encap_enable() function is part of the ipv6 code, and if that is
configured as a loadable module and rxrpc is built in then a build failure
will occur because the conditional check is wrong:
net/rxrpc/local_object.o: In function `rxrpc_lookup_local':
local_object.c:(.text+0x2688): undefined reference to `udpv6_encap_enable'
Use the correct config symbol (CONFIG_AF_RXRPC_IPV6) in the conditional
check rather than CONFIG_IPV6 as that will do the right thing.
Fixes: 5271953cad ("rxrpc: Use the UDP encap_rcv hook")
Reported-by: kbuild-all@01.org
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When commit 270972554c ("[IPV6]: ROUTE: Add Router Reachability
Probing (RFC4191).") introduced router probing, the rt6_probe() function
required that a neighbour entry existed. This neighbour entry is used to
record the timestamp of the last probe via the ->updated field.
Later, commit 2152caea71 ("ipv6: Do not depend on rt->n in rt6_probe().")
removed the requirement for a neighbour entry. Neighbourless routes skip
the interval check and are not rate-limited.
This patch adds rate-limiting for neighbourless routes, by recording the
timestamp of the last probe in the fib6_info itself.
Fixes: 2152caea71 ("ipv6: Do not depend on rt->n in rt6_probe().")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
net/rxrpc/output.c: In function 'rxrpc_reject_packets':
net/rxrpc/output.c:527:11: warning:
variable 'ioc' set but not used [-Wunused-but-set-variable]
'ioc' is the correct kvec num when sending a BUSY (or an ABORT) response
packet.
Fixes: ece64fec16 ("rxrpc: Emit BUSY packets when supposed to rather than ABORTs")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix an uninitialised variable introduced by the last patch. This can cause
a crash when a new call comes in to a local service, such as when an AFS
fileserver calls back to the local cache manager.
Fixes: c1e15b4944 ("rxrpc: Fix the packet reception routine")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the commit referred to below we added link tolerance as an additional
criteria for declaring broadcast transmission "stale" and resetting the
unicast links to the affected node.
Unfortunately, this 'improvement' introduced two bugs, which each and
one alone cause only limited problems, but combined lead to seemingly
stochastic unicast link resets, depending on the amount of broadcast
traffic transmitted.
The first issue, a missing initialization of the 'tolerance' field of
the receiver broadcast link, was recently fixed by commit 047491ea33
("tipc: set link tolerance correctly in broadcast link").
Ths second issue, where we omit to reset the 'stale_cnt' field of
the same link after a 'stale' period is over, leads to this counter
accumulating over time, and in the absence of the 'tolerance' criteria
leads to the above described symptoms. This commit adds the missing
initialization.
Fixes: a4dc70d46c ("tipc: extend link reset criteria for stale packet retransmission")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WHen an llc sock is added into the sk_laddr_hash of an llc_sap,
it is not marked with SOCK_RCU_FREE.
This causes that the sock could be freed while it is still being
read by __llc_lookup_established() with RCU read lock. sock is
refcounted, but with RCU read lock, nothing prevents the readers
getting a zero refcnt.
Fix it by setting SOCK_RCU_FREE in llc_sap_add_socket().
Reported-by: syzbot+11e05f04c15e03be5254@syzkaller.appspotmail.com
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to what has been done in 8b4c3cdd9d ("net: sched: Add policy
validation for tc attributes"), fix classifier code to add validation of
TCA_CHAIN and TCA_KIND netlink attributes.
tested with:
# ./tdc.py -c filter
v2: Let sch_api and cls_api share nla_policy they have in common, thanks
to David Ahern.
v3: Avoid EXPORT_SYMBOL(), as validation of those attributes is not done
by TC modules, thanks to Cong Wang.
While at it, restore the 'Delete / get qdisc' comment to its orginal
position, just above tc_get_qdisc() function prototype.
Fixes: 5bc1701881 ("net: sched: introduce multichain support for filters")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In dev_ethtool(), the eth command 'ethcmd' is firstly copied from the
use-space buffer 'useraddr' and checked to see whether it is
ETHTOOL_PERQUEUE. If yes, the sub-command 'sub_cmd' is further copied from
the user space. Otherwise, 'sub_cmd' is the same as 'ethcmd'. Next,
according to 'sub_cmd', a permission check is enforced through the function
ns_capable(). For example, the permission check is required if 'sub_cmd' is
ETHTOOL_SCOALESCE, but it is not necessary if 'sub_cmd' is
ETHTOOL_GCOALESCE, as suggested in the comment "Allow some commands to be
done by anyone". The following execution invokes different handlers
according to 'ethcmd'. Specifically, if 'ethcmd' is ETHTOOL_PERQUEUE,
ethtool_set_per_queue() is called. In ethtool_set_per_queue(), the kernel
object 'per_queue_opt' is copied again from the user-space buffer
'useraddr' and 'per_queue_opt.sub_command' is used to determine which
operation should be performed. Given that the buffer 'useraddr' is in the
user space, a malicious user can race to change the sub-command between the
two copies. In particular, the attacker can supply ETHTOOL_PERQUEUE and
ETHTOOL_GCOALESCE to bypass the permission check in dev_ethtool(). Then
before ethtool_set_per_queue() is called, the attacker changes
ETHTOOL_GCOALESCE to ETHTOOL_SCOALESCE. In this way, the attacker can
bypass the permission check and execute ETHTOOL_SCOALESCE.
This patch enforces a check in ethtool_set_per_queue() after the second
copy from 'useraddr'. If the sub-command is different from the one obtained
in the first copy in dev_ethtool(), an error code EINVAL will be returned.
Fixes: f38d138a7d ("net/ethtool: support set coalesce per queue")
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ethtool_get_rxnfc(), the eth command 'cmd' is compared against
'ETHTOOL_GRXFH' to see whether it is necessary to adjust the variable
'info_size'. Then the whole structure of 'info' is copied from the
user-space buffer 'useraddr' with 'info_size' bytes. In the following
execution, 'info' may be copied again from the buffer 'useraddr' depending
on the 'cmd' and the 'info.flow_type'. However, after these two copies,
there is no check between 'cmd' and 'info.cmd'. In fact, 'cmd' is also
copied from the buffer 'useraddr' in dev_ethtool(), which is the caller
function of ethtool_get_rxnfc(). Given that 'useraddr' is in the user
space, a malicious user can race to change the eth command in the buffer
between these copies. By doing so, the attacker can supply inconsistent
data and cause undefined behavior because in the following execution 'info'
will be passed to ops->get_rxnfc().
This patch adds a necessary check on 'info.cmd' and 'cmd' to confirm that
they are still same after the two copies in ethtool_get_rxnfc(). Otherwise,
an error code EINVAL will be returned.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2018-10-14
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix xsk map update and delete operation to not call synchronize_net()
but to piggy back on SOCK_RCU_FREE for sockets instead as we are not
allowed to sleep under RCU, from Björn.
2) Do not change RLIMIT_MEMLOCK in reuseport_bpf selftest if the process
already has unlimited RLIMIT_MEMLOCK, from Eric.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David writes:
"Networking
1) RXRPC receive path fixes from David Howells.
2) Re-export __skb_recv_udp(), from Jiri Kosina.
3) Fix refcounting in u32 classificer, from Al Viro.
4) Userspace netlink ABI fixes from Eugene Syromiatnikov.
5) Don't double iounmap on rmmod in ena driver, from Arthur
Kiyanovski.
6) Fix devlink string attribute handling, we must pull a copy into a
kernel buffer if the lifetime extends past the netlink request.
From Moshe Shemesh.
7) Fix hangs in RDS, from Ka-Cheong Poon.
8) Fix recursive locking lockdep warnings in tipc, from Ying Xue.
9) Clear RX irq correctly in socionext, from Ilias Apalodimas.
10) bcm_sf2 fixes from Florian Fainelli."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
net: dsa: bcm_sf2: Call setup during switch resume
net: dsa: bcm_sf2: Fix unbind ordering
net: phy: sfp: remove sfp_mutex's definition
r8169: set RX_MULTI_EN bit in RxConfig for 8168F-family chips
net: socionext: clear rx irq correctly
net/mlx4_core: Fix warnings during boot on driverinit param set failures
tipc: eliminate possible recursive locking detected by LOCKDEP
selftests: udpgso_bench.sh explicitly requires bash
selftests: rtnetlink.sh explicitly requires bash.
qmi_wwan: Added support for Gemalto's Cinterion ALASxx WWAN interface
tipc: queue socket protocol error messages into socket receive buffer
tipc: set link tolerance correctly in broadcast link
net: ipv4: don't let PMTU updates increase route MTU
net: ipv4: update fnhe_pmtu when first hop's MTU changes
net/ipv6: stop leaking percpu memory in fib6 info
rds: RDS (tcp) hangs on sendto() to unresponding address
net: make skb_partial_csum_set() more robust against overflows
devlink: Add helper function for safely copy string param
devlink: Fix param cmode driverinit for string type
devlink: Fix param set handling for string type
...
When booting kernel with LOCKDEP option, below warning info was found:
WARNING: possible recursive locking detected
4.19.0-rc7+ #14 Not tainted
--------------------------------------------
swapper/0/1 is trying to acquire lock:
00000000dcfc0fc8 (&(&list->lock)->rlock#4){+...}, at: spin_lock_bh
include/linux/spinlock.h:334 [inline]
00000000dcfc0fc8 (&(&list->lock)->rlock#4){+...}, at:
tipc_link_reset+0x125/0xdf0 net/tipc/link.c:850
but task is already holding lock:
00000000cbb9b036 (&(&list->lock)->rlock#4){+...}, at: spin_lock_bh
include/linux/spinlock.h:334 [inline]
00000000cbb9b036 (&(&list->lock)->rlock#4){+...}, at:
tipc_link_reset+0xfa/0xdf0 net/tipc/link.c:849
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&list->lock)->rlock#4);
lock(&(&list->lock)->rlock#4);
*** DEADLOCK ***
May be due to missing lock nesting notation
2 locks held by swapper/0/1:
#0: 00000000f7539d34 (pernet_ops_rwsem){+.+.}, at:
register_pernet_subsys+0x19/0x40 net/core/net_namespace.c:1051
#1: 00000000cbb9b036 (&(&list->lock)->rlock#4){+...}, at:
spin_lock_bh include/linux/spinlock.h:334 [inline]
#1: 00000000cbb9b036 (&(&list->lock)->rlock#4){+...}, at:
tipc_link_reset+0xfa/0xdf0 net/tipc/link.c:849
stack backtrace:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.19.0-rc7+ #14
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1af/0x295 lib/dump_stack.c:113
print_deadlock_bug kernel/locking/lockdep.c:1759 [inline]
check_deadlock kernel/locking/lockdep.c:1803 [inline]
validate_chain kernel/locking/lockdep.c:2399 [inline]
__lock_acquire+0xf1e/0x3c60 kernel/locking/lockdep.c:3411
lock_acquire+0x1db/0x520 kernel/locking/lockdep.c:3900
__raw_spin_lock_bh include/linux/spinlock_api_smp.h:135 [inline]
_raw_spin_lock_bh+0x31/0x40 kernel/locking/spinlock.c:168
spin_lock_bh include/linux/spinlock.h:334 [inline]
tipc_link_reset+0x125/0xdf0 net/tipc/link.c:850
tipc_link_bc_create+0xb5/0x1f0 net/tipc/link.c:526
tipc_bcast_init+0x59b/0xab0 net/tipc/bcast.c:521
tipc_init_net+0x472/0x610 net/tipc/core.c:82
ops_init+0xf7/0x520 net/core/net_namespace.c:129
__register_pernet_operations net/core/net_namespace.c:940 [inline]
register_pernet_operations+0x453/0xac0 net/core/net_namespace.c:1011
register_pernet_subsys+0x28/0x40 net/core/net_namespace.c:1052
tipc_init+0x83/0x104 net/tipc/core.c:140
do_one_initcall+0x109/0x70a init/main.c:885
do_initcall_level init/main.c:953 [inline]
do_initcalls init/main.c:961 [inline]
do_basic_setup init/main.c:979 [inline]
kernel_init_freeable+0x4bd/0x57f init/main.c:1144
kernel_init+0x13/0x180 init/main.c:1063
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:413
The reason why the noise above was complained by LOCKDEP is because we
nested to hold l->wakeupq.lock and l->inputq->lock in tipc_link_reset
function. In fact it's unnecessary to move skb buffer from l->wakeupq
queue to l->inputq queue while holding the two locks at the same time.
Instead, we can move skb buffers in l->wakeupq queue to a temporary
list first and then move the buffers of the temporary list to l->inputq
queue, which is also safe for us.
Fixes: 3f32d0be6c ("tipc: lock wakeup & inputq at tipc_link_reset()")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The XSKMAP update and delete functions called synchronize_net(), which
can sleep. It is not allowed to sleep during an RCU read section.
Instead we need to make sure that the sock sk_destruct (xsk_destruct)
function is asynchronously called after an RCU grace period. Setting
the SOCK_RCU_FREE flag for XDP sockets takes care of this.
Fixes: fbfc504a24 ("bpf: introduce new bpf AF_XDP map type BPF_MAP_TYPE_XSKMAP")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
In tipc_sk_filter_rcv(), when we detect protocol messages with error we
call tipc_sk_conn_proto_rcv() and let it reset the connection and notify
the socket by calling sk->sk_state_change().
However, tipc_sk_filter_rcv() may have been called from the function
tipc_backlog_rcv(), in which case the socket lock is held and the socket
already awake. This means that the sk_state_change() call is ignored and
the error notification lost. Now the receive queue will remain empty and
the socket sleeps forever.
In this commit, we convert the protocol message into a connection abort
message and enqueue it into the socket's receive queue. By this addition
to the above state change we cover all conditions.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the patch referred to below we added link tolerance as an additional
criteria for declaring broadcast transmission "stale" and resetting the
affected links.
However, the 'tolerance' field of the broadcast link is never set, and
remains at zero. This renders the whole commit without the intended
improving effect, but luckily also with no negative effect.
In this commit we add the missing initialization.
Fixes: a4dc70d46c ("tipc: extend link reset criteria for stale packet retransmission")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an MTU update with PMTU smaller than net.ipv4.route.min_pmtu is
received, we must clamp its value. However, we can receive a PMTU
exception with PMTU < old_mtu < ip_rt_min_pmtu, which would lead to an
increase in PMTU.
To fix this, take the smallest of the old MTU and ip_rt_min_pmtu.
Before this patch, in case of an update, the exception's MTU would
always change. Now, an exception can have only its lock flag updated,
but not the MTU, so we need to add a check on locking to the following
"is this exception getting updated, or close to expiring?" test.
Fixes: d52e5a7e7c ("ipv4: lock mtu in fnhe when received PMTU < net.ipv4.route.min_pmtu")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 5aad1de5ea ("ipv4: use separate genid for next hop
exceptions"), exceptions get deprecated separately from cached
routes. In particular, administrative changes don't clear PMTU anymore.
As Stefano described in commit e9fa1495d7 ("ipv6: Reflect MTU changes
on PMTU of exceptions for MTU-less routes"), the PMTU discovered before
the local MTU change can become stale:
- if the local MTU is now lower than the PMTU, that PMTU is now
incorrect
- if the local MTU was the lowest value in the path, and is increased,
we might discover a higher PMTU
Similarly to what commit e9fa1495d7 did for IPv6, update PMTU in those
cases.
If the exception was locked, the discovered PMTU was smaller than the
minimal accepted PMTU. In that case, if the new local MTU is smaller
than the current PMTU, let PMTU discovery figure out if locking of the
exception is still needed.
To do this, we need to know the old link MTU in the NETDEV_CHANGEMTU
notifier. By the time the notifier is called, dev->mtu has been
changed. This patch adds the old MTU as additional information in the
notifier structure, and a new call_netdevice_notifiers_u32() function.
Fixes: 5aad1de5ea ("ipv4: use separate genid for next hop exceptions")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fib6_info_alloc() function allocates percpu memory to hold per CPU
pointers to rt6_info, but this memory is never freed. Fix it.
Fixes: a64efe142f ("net/ipv6: introduce fib6_info struct and helpers")
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=q6E6
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-fixes-20181008' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Fix packet reception code
Here are a set of patches that prepares for and fix problems in rxrpc's
package reception code. There serious problems are:
(A) There's a window between binding the socket and setting the data_ready
hook in which packets can find their way into the UDP socket's receive
queues.
(B) The skb_recv_udp() will return an error (and clear the error state) if
there was an error on the Tx side. rxrpc doesn't handle this.
(C) The rxrpc data_ready handler doesn't fully drain the UDP receive
queue.
(D) The rxrpc data_ready handler assumes it is called in a non-reentrant
state.
The second patch fixes (A) - (C); the third patch renders (B) and (C)
non-issues by using the recap_rcv hook instead of data_ready - and the
final patch fixes (D). That last is the most complex.
The preparatory patches are:
(1) Fix some places that are doing things in the wrong net namespace.
(2) Stop taking the rcu read lock as it's held by the IP input routine in
the call chain.
(3) Only end the Tx phase if *we* rotated the final packet out of the Tx
buffer.
(4) Don't assume that the call state won't change after dropping the
call_state lock.
(5) Only take receive window and MTU suze parameters from an ACK packet if
it's the latest ACK packet.
(6) Record connection-level abort information correctly.
(7) Fix a trace line.
And then there are three main patches - note that these are mixed in with
the preparatory patches somewhat:
(1) Fix the setup window (A), skb_recv_udp() error check (B) and packet
drainage (C).
(2) Switch to using the encap_rcv instead of data_ready to cut out the
effects of the UDP read queues and get the packets delivered directly.
(3) Add more locking into the various packet input paths to defend against
re-entrance (D).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In rds_send_mprds_hash(), if the calculated hash value is non-zero and
the MPRDS connections are not yet up, it will wait. But it should not
wait if the send is non-blocking. In this case, it should just use the
base c_path for sending the message.
Signed-off-by: Ka-Cheong Poon <ka-cheong.poon@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devlink string param buffer is allocated at the size of
DEVLINK_PARAM_MAX_STRING_VALUE. Add helper function which makes sure
this size is not exceeded.
Renamed DEVLINK_PARAM_MAX_STRING_VALUE to
__DEVLINK_PARAM_MAX_STRING_VALUE to emphasize that it should be used by
devlink only. The driver should use the helper function instead to
verify it doesn't exceed the allowed length.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driverinit configuration mode value is held by devlink to enable the
driver fetch the value after reload command. In case the param type is
string devlink should copy the value from driver string buffer to
devlink string buffer on devlink_param_driverinit_value_set() and
vice-versa on devlink_param_driverinit_value_get().
Fixes: ec01aeb180 ("devlink: Add support for get/set driverinit value")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case devlink param type is string, it needs to copy the string value
it got from the input to devlink_param_value.
Fixes: e3b7ca18ad ("devlink: Add param set command")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rxrpc_input_packet() function and its call tree was built around the
assumption that data_ready() handler called from UDP to inform a kernel
service that there is data to be had was non-reentrant. This means that
certain locking could be dispensed with.
This, however, turns out not to be the case with a multi-queue network card
that can deliver packets to multiple cpus simultaneously. Each of those
cpus can be in the rxrpc_input_packet() function at the same time.
Fix by adding or changing some structure members:
(1) Add peer->rtt_input_lock to serialise access to the RTT buffer.
(2) Make conn->service_id into a 32-bit variable so that it can be
cmpxchg'd on all arches.
(3) Add call->input_lock to serialise access to the Rx/Tx state. Note
that although the Rx and Tx states are (almost) entirely separate,
there's no point completing the separation and having separate locks
since it's a bi-phasal RPC protocol rather than a bi-direction
streaming protocol. Data transmission and data reception do not take
place simultaneously on any particular call.
and making the following functional changes:
(1) In rxrpc_input_data(), hold call->input_lock around the core to
prevent simultaneous producing of packets into the Rx ring and
updating of tracking state for a particular call.
(2) In rxrpc_input_ping_response(), only read call->ping_serial once, and
check it before checking RXRPC_CALL_PINGING as that's a cheaper test.
The bit test and bit clear can then be combined. No further locking
is needed here.
(3) In rxrpc_input_ack(), take call->input_lock after we've parsed much of
the ACK packet. The superseded ACK check is then done both before and
after the lock is taken.
The handing of ackinfo data is split, parsing before the lock is taken
and processing with it held. This is keyed on rxMTU being non-zero.
Congestion management is also done within the locked section.
(4) In rxrpc_input_ackall(), take call->input_lock around the Tx window
rotation. The ACKALL packet carries no information and is only really
useful after all packets have been transmitted since it's imprecise.
(5) In rxrpc_input_implicit_end_call(), we use rx->incoming_lock to
prevent calls being simultaneously implicitly ended on two cpus and
also to prevent any races with incoming call setup.
(6) In rxrpc_input_packet(), use cmpxchg() to effect the service upgrade
on a connection. It is only permitted to happen once for a
connection.
(7) In rxrpc_new_incoming_call(), we have to recheck the routing inside
rx->incoming_lock to see if someone else set up the call, connection
or peer whilst we were getting there. We can't trust the values from
the earlier routing check unless we pin refs on them - which we want
to avoid.
Further, we need to allow for an incoming call to have its state
changed on another CPU between us making it live and us adjusting it
because the conn is now in the RXRPC_CONN_SERVICE state.
(8) In rxrpc_peer_add_rtt(), take peer->rtt_input_lock around the access
to the RTT buffer. Don't need to lock around setting peer->rtt.
For reference, the inventory of state-accessing or state-altering functions
used by the packet input procedure is:
> rxrpc_input_packet()
* PACKET CHECKING
* ROUTING
> rxrpc_post_packet_to_local()
> rxrpc_find_connection_rcu() - uses RCU
> rxrpc_lookup_peer_rcu() - uses RCU
> rxrpc_find_service_conn_rcu() - uses RCU
> idr_find() - uses RCU
* CONNECTION-LEVEL PROCESSING
- Service upgrade
- Can only happen once per conn
! Changed to use cmpxchg
> rxrpc_post_packet_to_conn()
- Setting conn->hi_serial
- Probably safe not using locks
- Maybe use cmpxchg
* CALL-LEVEL PROCESSING
> Old-call checking
> rxrpc_input_implicit_end_call()
> rxrpc_call_completed()
> rxrpc_queue_call()
! Need to take rx->incoming_lock
> __rxrpc_disconnect_call()
> rxrpc_notify_socket()
> rxrpc_new_incoming_call()
- Uses rx->incoming_lock for the entire process
- Might be able to drop this earlier in favour of the call lock
> rxrpc_incoming_call()
! Conflicts with rxrpc_input_implicit_end_call()
> rxrpc_send_ping()
- Don't need locks to check rtt state
> rxrpc_propose_ACK
* PACKET DISTRIBUTION
> rxrpc_input_call_packet()
> rxrpc_input_data()
* QUEUE DATA PACKET ON CALL
> rxrpc_reduce_call_timer()
- Uses timer_reduce()
! Needs call->input_lock()
> rxrpc_receiving_reply()
! Needs locking around ack state
> rxrpc_rotate_tx_window()
> rxrpc_end_tx_phase()
> rxrpc_proto_abort()
> rxrpc_input_dup_data()
- Fills the Rx buffer
- rxrpc_propose_ACK()
- rxrpc_notify_socket()
> rxrpc_input_ack()
* APPLY ACK PACKET TO CALL AND DISCARD PACKET
> rxrpc_input_ping_response()
- Probably doesn't need any extra locking
! Need READ_ONCE() on call->ping_serial
> rxrpc_input_check_for_lost_ack()
- Takes call->lock to consult Tx buffer
> rxrpc_peer_add_rtt()
! Needs to take a lock (peer->rtt_input_lock)
! Could perhaps manage with cmpxchg() and xadd() instead
> rxrpc_input_requested_ack
- Consults Tx buffer
! Probably needs a lock
> rxrpc_peer_add_rtt()
> rxrpc_propose_ack()
> rxrpc_input_ackinfo()
- Changes call->tx_winsize
! Use cmpxchg to handle change
! Should perhaps track serial number
- Uses peer->lock to record MTU specification changes
> rxrpc_proto_abort()
! Need to take call->input_lock
> rxrpc_rotate_tx_window()
> rxrpc_end_tx_phase()
> rxrpc_input_soft_acks()
- Consults the Tx buffer
> rxrpc_congestion_management()
- Modifies the Tx annotations
! Needs call->input_lock()
> rxrpc_queue_call()
> rxrpc_input_abort()
* APPLY ABORT PACKET TO CALL AND DISCARD PACKET
> rxrpc_set_call_completion()
> rxrpc_notify_socket()
> rxrpc_input_ackall()
* APPLY ACKALL PACKET TO CALL AND DISCARD PACKET
! Need to take call->input_lock
> rxrpc_rotate_tx_window()
> rxrpc_end_tx_phase()
> rxrpc_reject_packet()
There are some functions used by the above that queue the packet, after
which the procedure is terminated:
- rxrpc_post_packet_to_local()
- local->event_queue is an sk_buff_head
- local->processor is a work_struct
- rxrpc_post_packet_to_conn()
- conn->rx_queue is an sk_buff_head
- conn->processor is a work_struct
- rxrpc_reject_packet()
- local->reject_queue is an sk_buff_head
- local->processor is a work_struct
And some that offload processing to process context:
- rxrpc_notify_socket()
- Uses RCU lock
- Uses call->notify_lock to call call->notify_rx
- Uses call->recvmsg_lock to queue recvmsg side
- rxrpc_queue_call()
- call->processor is a work_struct
- rxrpc_propose_ACK()
- Uses call->lock to wrap __rxrpc_propose_ACK()
And a bunch that complete a call, all of which use call->state_lock to
protect the call state:
- rxrpc_call_completed()
- rxrpc_set_call_completion()
- rxrpc_abort_call()
- rxrpc_proto_abort()
- Also uses rxrpc_queue_call()
Fixes: 17926a7932 ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both")
Signed-off-by: David Howells <dhowells@redhat.com>
Fix connection-level abort handling to cache the abort and error codes
properly so that a new incoming call can be properly aborted if it races
with the parent connection being aborted by another CPU.
The abort_code and error parameters can then be dropped from
rxrpc_abort_calls().
Fixes: f5c17aaeb2 ("rxrpc: Calls should only have one terminal state")
Signed-off-by: David Howells <dhowells@redhat.com>
Move the out-of-order and duplicate ACK packet check to before the call to
rxrpc_input_ackinfo() so that the receive window size and MTU size are only
checked in the latest ACK packet and don't regress.
Fixes: 248f219cb8 ("rxrpc: Rewrite the data and ack handling code")
Signed-off-by: David Howells <dhowells@redhat.com>
Carry the call state out of the locked section in rxrpc_rotate_tx_window()
rather than sampling it afterwards. This is only used to select tracepoint
data, but could have changed by the time we do the tracepoint.
Signed-off-by: David Howells <dhowells@redhat.com>
Roopa Prabhu