Return value check of atomic_dec_if_positive is required as it returns
old value minus one. Without this fix, driver will send small ios to
firmware path and that will be a performance issue.
Not critical, but good to have r1_ldio_hint as default value in sdev
private.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Without this fix, driver will enable INTx Interrupt pin even though
MSI-x vectors are enabled. See below lspci output. DisINTx is unset for
MSIx setup.
lspci -s 85:00.0 -vvv |grep INT |grep Control
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
After applying this fix, driver will enable INTx Interrupt pin only if
Legacy interrupt method is required. See below lspci output. DisINTx is
set for MSIx setup. lspci -s 85:00.0 -vvv |grep INT |grep Control
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When building with a dma_addr_t that is different from pointer size, we
get this warning:
drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_make_prp_nvme':
drivers/scsi/megaraid/megaraid_sas_fusion.c:1654:17: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
It's better to not pretend that the dma address is a pointer and instead
use a dma_addr_t consistently.
Fixes: 33203bc4d6 ("scsi: megaraid_sas: NVME fast path io support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The "sz" variable is in terms of bytes, but we're treating the buffer as
an array of __le32 so we have to divide by 4.
Fixes: def0eab3af ("scsi: megaraid_sas: enhance debug logs in OCR context")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For RAID1 FastPath writes, driver needs to allocate extra commands
internally to accommodate for the extra peer command being sent.
Currently driver is allocating 2 extra commands for each but only one
extra command is necessary. Set RAID_1_10_RMW_CMDS to 2 and also change
macro name to RAID_1_PEER_CMDS.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix indentation issues and smatch warning reported by Dan Carpenter
for previous series as discussed below.
http://www.spinics.net/lists/linux-scsi/msg103635.htmlhttp://www.spinics.net/lists/linux-scsi/msg103603.html
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix - increase internal command pool to 8.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
FIX - Do not use random delay to synchronize with IRQ. Use kernel API.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Error handling: Bail out the driver load if key FW cmds (LD_LIST) are
not return successful. Clean up error handling in megasas_init_fw.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Code refactoring to build_mpt_mfi_pass_thru to return void.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Error handling: If controller reset is not able to recover, kill HBA and
quit immediately.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
FIX - firmware wants non-RW SYS PD IOs to avoid FastPath for better
tracking and other functionalities if the device is task management
capable.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Memset the IO frame to zero after release.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix to account for the reply_q_sz not exceeding the maximum commands
that the firmware can support, instance->max_fw_cmds is already
decremented in megasas_fusion_update_can_queue(). Remove the extra
decrement logic in code.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Minor Optimization: No need to update HBA can_queue value if the current
max FW commands is equal to earlier value.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since maximum supported FW commands are all defined as u16, change
all local variables referring to max_cmd from u32 to u16.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Issue is limited for Syncro firmware where pd_after_lb is not set but is
accidentally used. Not a functional issue, but results in low
performance due to improper load balancing between two LUNs.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fetch the latest controller OCR capability from FW before sending
MR_DCMD_CTRL_SHUTDOWN When application sends a shutdown DCMD
(MR_DCMD_CTRL_SHUTDOWN), driver will fetch latest controller information
from firmware. This is to ensure that driver always has latest OCR
capability of controller before sending the DCMD.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix kernel warning for accessing unaligned memory access in driver.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix endiannes fixes for Ventura specific.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix if RDPQ mode enabled MR FW is deployed on big endian host machine,
driver does not setup reply address correctly.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change MR_TargetIdToLdGet return type from u8 to u16.
ld id range check is added at two places in this patch -
@megasas_build_ldio_fusion and @megasas_build_ld_nonrw_fusion. Previous
driver code used different data type for lds TargetId returned from
MR_TargetIdToLdGet. Prior to this change, above two functions was
safeguarded due to function always return u8 and maximum value of ld id
returned was 255.
In below check, fw_supported_vd_count as of today is 64 or 256 and valid
range to support is either 0-63 or 0-255. Ideally want to filter
accessing raid map for ld ids which are not valid. With the u16 change,
invalid ld id value is 0xFFFF and we will see kernel panic due to random
memory access in MR_LdRaidGet. The changes will ensure we do not call
MR_LdRaidGet if ld id is beyond size of ldSpanMap array.
if (ld < instance->fw_supported_vd_count)
>From firmware perspective,ld id 0xFF is invalid and even though current
driver code forward such command, firmware fails with target not
available.
ld target id issue occurs mainly whenever driver loops to populate raid
map (ea. MR_ValidateMapInfo). These are the only two places where we
may see out of range target ids and wants to protect raid map access
based on range provided by Firmware API.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On a host, if an ld is deleted there is a hole in the ld array returned
by the FW. But in MR_ValidateMapInfo we are not accounting for holes in
the ld array and traverse only upto index num_lds. This patch takes
care of converting the capability field of all the valid lds in the ld
raid map.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently fusion context has fixed array load_balance_info. Use dynamic
allocation. In few places, driver do not want physically contigious
memory. Attempt to use vmalloc if physical contiguous memory is not
available.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add additional logging from driver in OCR context.
Add debug logs for partial completion of IOs is iodone context.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixing issue of not setting residual bytes correctly.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid Host side PCI bandwidth bottleneck and hint FW to do Write
buffering using RaidFlag MR_RAID_FLAGS_IO_SUB_TYPE_LDIO_BW_LIMIT. Once
IO is landed in FW with MR_RAID_FLAGS_IO_SUB_TYPE_LDIO_BW_LIMIT, it will
do single DMA from host and buffer the Write operation. On back end, FW
will DMA same buffer to the Mirror and Data Arm. This will improve
large block IO performance which bottleneck due to Host side PCI
bandwidth limitation.
Consistent ~4000MB T.P for 256K Block size is expected performance
numbers. IOPS for small Block size should be on par with Disk
performance. (E.g 42 SAS Disk in JBOD mode gives 3700MB T.P. Same
Drive used in R1 WT mode, should give ~1800MB T.P)
Using this patch 24 R1 VDs (HDD) gives below performance for Sequential
Write. Without this patch, we cannot reach above 3200MB (Throughput is
in MB.)
Block Size 50% 256K and 50% 4K 100% 256K
4K 3100 2030
8K 3140 2740
16K 3140 3140
32K 3400 3240
64K 3500 3700
128K 3870 3870
256K 3920 3920
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch provide true fast path IO support. Driver creates PRP for
NVME drives and send Fast Path for performance. Certain h/w requirement
needs to be taken care in driver.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fetch true values of NVME property from FW using New DCMD
interface MR_DCMD_DEV_GET_TARGET_PROP
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Adding detection logic for NVME device attached behind Ventura
controller. Driver set HostPageSize in IOC_INIT frame to inform about
page size for NVME devices. Firmware reports NVME page size to the
driver. PD INFO DCMD provide new interface type NVME_PD. Driver set
property of NVME device.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With the changes to remove checks for a valid request descriptor,
issue_dcmd will now always return DCMD_SUCCESS. This patch changes
return type of issue_dcmd to void and change all callers appropriately.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional change. Code clean up. Removing error code which is not
valid scenario. In megasas_get_request_descriptor we can remove the
error handling which is not required. With fusion controllers, if there
is a valid message frame available, we are guaranteed to get a
corresponding request descriptor.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Moving to use DID_REQUEUE return type for reliable unconditional
retries. Driver wants unconditional re-queue, so replace DID_RESET with
DID_REQUEUE
Discussed below -
https://www.spinics.net/lists/linux-scsi/msg102848.html
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional change. Code refactor.
megasas_fire_cmd_fusion can always use 32 bit descriptor write for
ventura. No need to pass extra flag. Only IOC INIT required 64 bit
Descriptor write.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional change. Code refactor.
Remove function megasas_fpio_to_ldio as we never require to convert fpio
to ldio because of frame unavailability. Grab extra frame of raid 1
write fast path before it creates first frame as Fast Path. Removed
is_raid_1_fp_write flag as raid 1 write fast path command is decided
using r1_alt_dev_handle only. Move resetting megasas_cmd_fusion fields
at common function megasas_return_cmd_fusion.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional change. Code refactor.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This reverts commit "3e5eadb1a881" ("scsi: megaraid_sas: Enable or
Disable Fast path based on the PCI Threshold Bandwidth")
This patch was aimed to increase performance of R1 Write operation for
large IO size. Since this method used timer approach, it turn on/off
fast path did not work as expected. Patch 0013 describes new algorithm
and performance number.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update Linux driver to use new pdTargetId field for JBOD target ID
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ldio outstanding variable needs to be decremented in io completion path for
iMR dual queue depth
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Large SEQ IO workload should sent as non fast path commands
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The Megaraid driver has to support the SAS3.5 Generic Megaraid Controllers Firmware functionality.
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SAS3.5 Generic Megaraid Controllers FW will support new dynamic RaidMap to have different
sizes for different number of supported VDs.
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To improve RAID 1/10 Write performance, OS drivers need to issue the
required Write IOs as Fast Path IOs (after the appropriate checks
allowing Fast Path to be used) to the appropriate physical drives
(translated from the OS logical IO) and wait for all Write IOs to complete.
Design: A write IO on RAID volume will be examined if it can be sent in
Fast Path based on IO size and starting LBA and ending LBA falling on to
a Physical Drive boundary. If the underlying RAID volume is a RAID 1/10,
driver issues two fast path write IOs one for each corresponding physical
drive after computing the corresponding start LBA for each physical drive.
Both write IOs will have the same payload and are posted to HW such that
replies land in the same reply queue.
If there are no resources available for sending two IOs, driver will send
the original IO from SCSI layer to RAID volume through the Firmware.
Based on PCI bandwidth and write payload, every second this feature is
enabled/disabled.
When both IOs are completed by HW, the resources will be released
and SCSI IO completion handler will be called.
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Detect sequential Write IOs and pass the hint that it is part of sequential
stream to help HBA Firmware do the Full Stripe Writes. For read IOs on
certain RAID volumes like Read Ahead volumes,this will help driver to
send it to Firmware even if the IOs can potentially be sent to
hardware directly (called fast path) bypassing firmware.
Design: 8 streams are maintained per RAID volume as per the combined
firmware/driver design. When there is no stream detected the LRU stream
is used for next potential stream and LRU/MRU map is updated to make this
as MRU stream. Every time a stream is detected the MRU map
is updated to make the current stream as MRU stream.
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
An UNMAP command on a PI formatted device will leave the Logical Block Application
Tag and Logical Block Reference Tag as all F's (for those LBAs that are unmapped).
To avoid IO errors if those LBAs are subsequently read before they are written with
valid tag fields, the MPI SCSI IO requests need to set the EEDPFlags element EEDP
Escape Mode field, Bits [7:6] appropriately. A value of 2 should be set to disable
all PI checks if the Logical Block Application Tag is 0xFFFF for PI types 1 and 2.
A value of 3 should be set to disable all PI checks if the Logical Block Application
Tag is 0xFFFF and the Logical Block Reference Tag is 0xFFFFFFFF for PI type 3.
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SAS3.5 Generic Megaraid based Controllers will have the support for 128 MSI-X vectors,
resulting in the need to support 128 reply queues
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch contains new pci device ids for SAS3.5 Generic Megaraid Controllers
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This update includes the usual round of major driver updates (ncr5380,
lpfc, hisi_sas, megaraid_sas, ufs, ibmvscsis, mpt3sas). There's also
an assortment of minor fixes, mostly in error legs or other not very
user visible stuff. The major change is the pci_alloc_irq_vectors
replacement for the old pci_msix_.. calls; this effectively makes IRQ
mapping generic for the drivers and allows blk_mq to use the
information.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sPXh
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This update includes the usual round of major driver updates (ncr5380,
lpfc, hisi_sas, megaraid_sas, ufs, ibmvscsis, mpt3sas).
There's also an assortment of minor fixes, mostly in error legs or
other not very user visible stuff. The major change is the
pci_alloc_irq_vectors replacement for the old pci_msix_.. calls; this
effectively makes IRQ mapping generic for the drivers and allows
blk_mq to use the information"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (256 commits)
scsi: qla4xxx: switch to pci_alloc_irq_vectors
scsi: hisi_sas: support deferred probe for v2 hw
scsi: megaraid_sas: switch to pci_alloc_irq_vectors
scsi: scsi_devinfo: remove synchronous ALUA for NETAPP devices
scsi: be2iscsi: set errno on error path
scsi: be2iscsi: set errno on error path
scsi: hpsa: fallback to use legacy REPORT PHYS command
scsi: scsi_dh_alua: Fix RCU annotations
scsi: hpsa: use %phN for short hex dumps
scsi: hisi_sas: fix free'ing in probe and remove
scsi: isci: switch to pci_alloc_irq_vectors
scsi: ipr: Fix runaway IRQs when falling back from MSI to LSI
scsi: dpt_i2o: double free on error path
scsi: cxlflash: Migrate scsi command pointer to AFU command
scsi: cxlflash: Migrate IOARRIN specific routines to function pointers
scsi: cxlflash: Cleanup queuecommand()
scsi: cxlflash: Cleanup send_tmf()
scsi: cxlflash: Remove AFU command lock
scsi: cxlflash: Wait for active AFU commands to timeout upon tear down
scsi: cxlflash: Remove private command pool
...
[mkp: fixed bad indentation]
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It is not good when an irq arrives before driver structures are
allocated.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A couple of dev_printk messages spans two lines and the literal string
is missing a white space between words. Add the white space.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch will fix regression caused by commit 1e793f6fc0 ("scsi:
megaraid_sas: Fix data integrity failure for JBOD (passthrough)
devices").
The problem was that the MEGASAS_IS_LOGICAL macro did not have braces
and as a result the driver ended up exposing a lot of non-existing SCSI
devices (all SCSI commands to channels 1,2,3 were returned as
SUCCESS-DID_OK by driver).
[mkp: clarified patch description]
Fixes: 1e793f6fc0
Reported-by: Jens Axboe <axboe@kernel.dk>
CC: stable@vger.kernel.org
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Tested-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Tested-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
CC: stable@vger.kernel.org
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Until now the megaraid_sas driver has reported successful completion on
SYNCHRONIZE_CACHE commands without sending them down to the controller.
The controller firmware has been responsible for taking care of flushing
disk caches for all drives that belong to a Virtual Disk at the time of
system reboot/shutdown.
There may have been a reason to avoid sending SYNCHRONIZE_CACHE to a VD
in the past but that no longer appears to be valid.
Older versions of MegaRaid firmware (Gen2 and Gen2.5) set the WCE bit
for Virtual Disks but the firmware does not report correct completion
status for a SYNCHRONIZE_CACHE command. As a result, we must use another
method to identify whether it is safe to send the command to the
controller. We use the canHandleSyncCache firmware flag in the scratch
pad register at offset 0xB4.
New SYNCHRONIZE_CACHE behavior:
IF 'JBOD'
Driver sends SYNCHRONIZE_CACHE command to the firmware
Firmware sends SYNCHRONIZE_CACHE to drive
Firmware obtains status from drive and returns same status back to driver
ELSEIF 'VirtualDisk'
IF firmware supports new API bit called canHandleSyncCache
Driver sends SYNCHRONIZE_CACHE command to the firmware
Firmware does not send SYNCHRONIZE_CACHE to drives
Firmware returns SUCCESS
ELSE
Driver does not send SYNCHRONIZE_CACHE command to the firmware
Driver return SUCCESS for that command
ENDIF
ENDIF
[mkp: edited patch description]
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch addresses the issue of driver firing DCMDs in PCI
shutdown/detach path irrespective of firmware state. Driver will now
check whether firmware is in operational state or not before firing
DCMDs. If firmware is in unrecoverable state or does not become
operational within specfied time, driver will skip firing DCMDs.
[mkp: fixed typos]
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan Srikanteshwara <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes the issue of wrong PhysArm was sent to firmware for R1
VD downgrade.
Signed-off-by: Kiran Kumar Kasturi <kiran-kumar.kasturi@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For SRIOV enabled firmware, if there is a OCR(online controller reset)
possibility driver set the convert flag to 1, which is not happening if
there are outstanding commands even after 180 seconds. As driver does
not set convert flag to 1 and still making the OCR to run, VF(Virtual
function) driver is directly writing on to the register instead of
waiting for 30 seconds. Setting convert flag to 1 will cause VF driver
will wait for 30 secs before going for reset.
CC: stable@vger.kernel.org
Signed-off-by: Kiran Kumar Kasturi <kiran-kumar.kasturi@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 02b01e010a ("megaraid_sas: return sync cache call with
success") modified the driver to successfully complete SYNCHRONIZE_CACHE
commands without passing them to the controller. Disk drive caches are
only explicitly managed by controller firmware when operating in RAID
mode. So this commit effectively disabled writeback cache flushing for
any drives used in JBOD mode, leading to data integrity failures.
[mkp: clarified patch description]
Fixes: 02b01e010a
CC: stable@vger.kernel.org
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This update includes the usual round of major driver updates (hpsa, be2iscsi,
hisi_sas, zfcp, cxlflash). There's a new incarnation of hpsa called smartpqi
for which a driver is added, there's some cleanup work of the ibm vscsi target
and updates to libfc, plus a whole host of minor fixes and updates and finally
the removal of several ISA drivers which seem not to have been used for years.
Signed-off-by: James Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJX9fZGAAoJEAVr7HOZEZN4TfkP/2bOHBGqyQ16P9jRjWXtC6pJ
Fp/ZfU6ZrSpcGN49Wr9vyPbpvYKdtIZg3oUs6XhKmnfP+lbeIIJ5jxlEnwBVwWya
JOOD91o8lLN7zRMuyfYIfgnm4dIU3GSLpnWIyfAhoMH1utiLLcq7s2XEM5girDft
dVUL20XprtJkVsg2C+hhRAI8PMjWFInadj2eRIHdxJIDC8fXR+w8ojBShou+lf6Q
/zYPgckTCBlZWIc/ohI3j52r4qmkChgX+3/jR+v9i5bGXjFfpmh0GzxM7tscESSa
4Y/ZLTg72j/colYkA1jt04YLxA2dQCa6b8DmJIcUTL0WStsJUQH5hFFFHt3mSafI
HirqRfHpmadHbfi5Kiyx688S5b0oVN4bMxvMoEOAUy7WVaLEr84GJ5VYhoAwkPhL
USaDx6Hsa1OT0lGYAtyRKOUT/d55grztEOnSxBFiQgRoB8wrGX616Xg8VONy7JZS
wEZtf1v5K0+ZXJiu4NtY+/RzQdOwu7OQHKfN5mLri8tJ+eo8d88ZwSARJxEZetSM
P4EVR2ZjhL+Ct78v3i4Yj8FVMXHSzzulj530KQ/U7z/l4c2S54mtEKijDmXmto8k
baiIah/wgaS/fznoOsJw+Iy/2HqsAtNZsReNcgNPLzfabTBXKSBXJDLmO4d3g/3s
zwj1m3JtzAx2j3kQrkSv
=cyTO
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This update includes the usual round of major driver updates (hpsa,
be2iscsi, hisi_sas, zfcp, cxlflash). There's a new incarnation of hpsa
called smartpqi for which a driver is added, there's some cleanup work
of the ibm vscsi target and updates to libfc, plus a whole host of
minor fixes and updates and finally the removal of several ISA drivers
which seem not to have been used for years"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (173 commits)
scsi: mvsas: Mark symbols static where possible
scsi: pm8001: Mark symbols static where possible
scsi: arcmsr: Simplify user_len checking
scsi: fcoe: fix off by one in eth2fc_speed()
scsi: dtc: remove from tree
scsi: t128: remove from tree
scsi: pas16: remove from tree
scsi: u14-34f: remove from tree
scsi: ultrastor: remove from tree
scsi: in2000: remove from tree
scsi: wd7000: remove from tree
scsi: scsi_dh_alua: Fix memory leak in alua_rtpg()
scsi: lpfc: Mark symbols static where possible
scsi: hpsa: correct call to hpsa_do_reset
scsi: ufs: Get a TM service response from the correct offset
scsi: ibmvfc: Fix I/O hang when port is not mapped
scsi: megaraid_sas: clean function declarations in megaraid_sas_base.c up
scsi: ipr: Remove redundant messages at adapter init time
scsi: ipr: Don't log unnecessary 9084 error details
scsi: smartpqi: raid bypass lba calculation fix
...
We get a few warnings when building kernel with W=1:
drivers/scsi/megaraid/megaraid_sas_fusion.c:281:1: warning: no previous prototype for 'megasas_free_cmds_fusion' [-Wmissing-prototypes]
drivers/scsi/megaraid/megaraid_sas_fusion.c:714:1: warning: no previous prototype for 'megasas_ioc_init_fusion' [-Wmissing-prototypes]
....
In fact, these functions are declared in
drivers/scsi/megaraid/megaraid_sas_base.c, but should be declared in a
header file, thus can be recognized in other file.
So this patch adds the declarations into
drivers/scsi/megaraid/megaraid_sas_fusion.h.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A dev_printk message spans two lines and the literal string is missing a
white space between words. Add the white space.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The 2nd parameter of 'find_first_bit' is the number of bits to search.
In this case, we are passing 'sizeof(unsigned long)' which is likely to
be 4.
It is likely that the number of bits in a long was expected here, so use
BITS_PER_LONG instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reuse existing functionality from memdup_user() instead of keeping
duplicate source code.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Found one megaraid_sas HBA probe fails,
[ 187.235190] scsi host2: Avago SAS based MegaRAID driver
[ 191.112365] megaraid_sas 0000:89:00.0: BAR 0: can't reserve [io 0x0000-0x00ff]
[ 191.120548] megaraid_sas 0000:89:00.0: IO memory region busy!
and the card has resource like,
[ 125.097714] pci 0000:89:00.0: [1000:005d] type 00 class 0x010400
[ 125.104446] pci 0000:89:00.0: reg 0x10: [io 0x0000-0x00ff]
[ 125.110686] pci 0000:89:00.0: reg 0x14: [mem 0xce400000-0xce40ffff 64bit]
[ 125.118286] pci 0000:89:00.0: reg 0x1c: [mem 0xce300000-0xce3fffff 64bit]
[ 125.125891] pci 0000:89:00.0: reg 0x30: [mem 0xce200000-0xce2fffff pref]
that does not io port resource allocated from BIOS, and kernel can not
assign one as io port shortage.
The driver is only looking for MEM, and should not fail.
It turns out megasas_init_fw() etc are using bar index as mask. index 1
is used as mask 1, so that pci_request_selected_regions() is trying to
request BAR0 instead of BAR1.
Fix all related reference.
Fixes: b6d5d8808b ("megaraid_sas: Use lowest memory bar for SR-IOV VF support")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There was an issue reported by Lucz Geza on Dell Perc 6i. As per issue
reported, megaraid_sas driver goes into an infinite error reporting loop
as soon as there is a change in the status of one of the
arrays (degrade, resync online etc ). Below are the error logs reported
continuously-
Jun 25 08:49:30 ns8 kernel: [ 757.757017] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
Jun 25 08:49:30 ns8 kernel: [ 757.778017] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
Jun 25 08:49:30 ns8 kernel: [ 757.799017] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
Jun 25 08:49:30 ns8 kernel: [ 757.820018] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
Jun 25 08:49:30 ns8 kernel: [ 757.841018] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
This issue is very much specific to controllers which do not support
DCMD- MR_DCMD_PD_LIST_QUERY. In case of any hotplugging/rescanning of
drives, AEN thread will be scheduled by driver and fire DCMD-
MR_DCMD_PD_LIST_QUERY and if this DCMD is failed then driver will fail
this event processing and will not go ahead for further events. This
will cause infinite loop of same event getting retried infinitely and
causing above mentioned logs.
Fix for this problem is: not to fire DCMD MR_DCMD_PD_LIST_QUERY for
controllers which do not support it and send DCMD SUCCESS status to AEN
function so that it can go ahead with other event processing.
Reported-by: Lucz Geza <geza@lucz.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
I actually read the error messages in my logs, and successful
initialization is not an error.
Arguably these log lines could be deleted entirely.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch will do code optmization for task management functions.
Below are key changes:
1. Remove reset_device hook as it was not being used and driver was
setting this to NULL.
2. Create wrapper functions for task abort and target reset and inside
these functions adapter specific calls be made. e.g. fusion adapters
support task abort and target reset so task abort and target reset
should be issued to fusion adapters only and for MFI adapters, print
a message saying feature not supported.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In OCR path, before calling chip reset calls function
megasas_wait_for_outstanding_fusion to check reason for OCR. In case of
firmware FAULT initiated OCR and DCMD timeout initiated timeout, driver
will clear any outstanding reply (yet to be processed by driver) in
reply queues before going for chip reset. This code is added to handle a
scenario when IO timeout initiated adapter reset and management
application initiated adapter reset (by sending command to FAULT
firmware) happens simultaneously since adapter reset function is
safe-guarded by reset_mutex so only thread will be doing controller
reset. Consider IO timeout thread gets mutex and proceeds with adapter
reset process after disabling interrupts and by the time management
application has fired command to firmware to do adapter reset and the
same command is completed by firmware but since interrupts are disabled,
driver will not get completion and the same command will be in
outstanding/pending commands list of driver and refires same command
from IO timeout thread after chip reset which will again FAULT firmware
and eventually causes kill adapter.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch will reduce memory footprints of megaraid_sas driver when
booted in kdump mode. Driver will not allocate memory for optional and
perfromance oriented features. Below are key changes done in
megaraid_sas driver to do this:
1. Limit Controller's queue depth to 100 in kdump mode.
2. Do not allocate memory for system info buffer and PD info buffer.
3. Disable performance oriented features e.g. Disable RDPQ mode, disable
dual queue depth, restrict to single MSI-x vector.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
gcc-6 found a dubious indentation in the megasas_mgmt_fw_ioctl
function:
drivers/scsi/megaraid/megaraid_sas_base.c: In function 'megasas_mgmt_fw_ioctl':
drivers/scsi/megaraid/megaraid_sas_base.c:6658:4: warning: statement is indented as if it were guarded by... [-Wmisleading-indentation]
kbuff_arr[i] = NULL;
^~~~~~~~~
drivers/scsi/megaraid/megaraid_sas_base.c:6653:3: note: ...this 'if' clause, but it is not
if (kbuff_arr[i])
^~
The code is actually correct, as there is no downside in clearing a NULL
pointer again.
This clarifies the code and avoids the warning by adding extra curly
braces.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 90dc9d98f0 ("megaraid_sas : MFI MPT linked list corruption fix")
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are few MFI adapters which do not support MR_DCMD_PD_LIST_QUERY so
if MFI adapters fail this DCMD, it should not be considered as FATAL and
driver should not issue kill adapter and set per controller's instance
variable- pd_list_not_supported so that same variable can be used inside
functions- slave_alloc and slave_configure to allow firmware scan.
Killing adapter because of DCMD failure when this DCMD is not supported
causes driver's probe getting failed. This issue got introduced by
commit 6d40afbc7d ("megaraid_sas: MFI IO timeout handling").
Killing adapter in case of this DCMD failure should be limited to Fusion
adapters only. Per controller's instance variable allow_fw_scan is
removed as pd_list_not_supported better reflect the purpose.
Fixes: 6d40afbc7d
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A barrier should be added to ensure proper ordering of memory mapped
writes.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Kashyap Desai <kashyap.desai@broadcom.com>
Acked-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Inside compat IOCTL hook of driver, driver was using wrong address of
ioc->frame.raw which leads sense_ioc_ptr to be calculated wrongly and
failing IOCTL.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver assumes that VFs always have peers present whenever they have
same LD IDs. But this is not the case. This patch handles the above
mentioned by explicitly checking for a peer before making HA/non-HA path
decision.
Signed-off-by: Uday Lingala <uday.lingala@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The pd_seq_sync pointer can't be NULL, we have to check its entries
instead.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes online controller resets on SRIOV-enabled series of
Avago controllers.
1) Remove late detection heartbeat.
2) Change in the behavior if the FW found in READY/OPERATIONAL state.
Signed-off-by: Uday Lingala <uday.lingala@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch will introduce module-parameter for SCSI command timeout
value and fix setting of resetwaittime beyond a value.
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make instance->adprecovery variable atomic and removes hba_lock spinlock
while accessing instance->adprecovery.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch will add capability in driver to tell firmware that it can
throttle IOs in case controller's queue depth is downgraded post OFU
(online firmware upgrade). This feature will ensure firmware can be
downgraded from higher queue depth to lower queue depth without needing
system reboot. Added throttling code in IO path of driver, in case OS
tries to send more IOs than post OFU firmware's queue depth.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1. For iMR controllers, firmware will report two queue depths:
- Controller-wide queue depth
- LDIO queue depth (240)
Controller-wide queue depth will be greater among the two. Using this
new feature, iMR can provide larger Queue depth(QD) for JBOD and limited
QD for Virtual Disk(VD).
2. megaraid_sas driver will throttle read/write LDIOs based on "LDIO
Queue Depth".
3. Dual queue depth can be enabled/disabled via module parameter. It is
enabled by default if the firmware supports it. Only specific firmware
builds will enable the feature.
4. Added sysfs parameter "ldio_outstanding" which permits querying the
number of outstanding LDIO requests at runtime.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
build_and_issue_cmd should return SCSI_MLQUEUE_HOST_BUSY for a few error
cases instead of returning 1.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch will create a reply queue pool for each MSI-X index and will
provide an array of base addresses instead of the single address of
legacy mode. Using this new interface the driver can support higher
queue depths through scattered DMA pools.
If array mode is not supported driver will fall back to the legacy
method of reply pool allocation. This limits controller queue depth to
1K max. To enable a queue depth of more than 1K driver requires firmware
to support array mode and scratch_pad3 will provide the new queue depth
value.
When RDPQ is used, downgrading to an older firmware release should not
be permitted. This may cause firmware fault and is not supported.
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Firmware will fill out per-LD data to tell driver whether a particular
LD supports region lock bypass. If yes, then driver will send non-FP
LDIO to region lock bypass FIFO. With this change in driver, firmware
will optimize certain code to improve performance.
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch will update device Queue depth based on interface type(SAS,
SATA..) for sysPDs. For Virtual disks(VDs), there will be no change in
queue depth (will remain 256). To fetch interface type (SAS or SATA or
FC..) of syspD, driver will send DCMD MR_DCMD_PD_GET_INFO.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds task management for SCSI commands. Added functions are
task abort and target reset.
1. Currently, megaraid_sas driver performs controller reset when any IO
times out. With task management support added, task abort and target
reset will be tried to recover timed out IO. If task management fails,
then controller reset will be performaned. If the task management
request times out, fail the request and escalate to the next
level (controller reset).
2. mr_device_priv_data will be allocated for all generations of
controller, but is_tm_capable flag will never be set for
controllers (prior to Invader series) as firmware support is not
available for task management.
3. Task management capable firmware will set is_tm_capable flag in
firmware API.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch will do proper error handling for DCMD timeout failure cases
for Fusion adapters:
1. For MFI adapters, in case of DCMD timeout (DCMD which must return
SUCCESS) driver will call kill adapter.
2. What action needs to be taken in case of DCMD timeout is decided by
function dcmd_timeout_ocr_possible(). DCMD timeout causing OCR is
applicable to the following commands:
MR_DCMD_PD_LIST_QUERY
MR_DCMD_LD_GET_LIST
MR_DCMD_LD_LIST_QUERY
MR_DCMD_CTRL_SET_CRASH_DUMP_PARAMS
MR_DCMD_SYSTEM_PD_MAP_GET_INFO
MR_DCMD_LD_MAP_GET_INFO
3. If DCMD fails from driver init path there are certain DCMDs which
must return SUCCESS. If those DCMDs fail, driver bails out. For optional
DCMDs like pd_info etc., driver continues without executing certain
functionality.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch will do synhronization between OCR function and AEN function
using "reset_mutex" lock. reset_mutex will be acquired only in the
first half of the AEN function which issues a DCMD. Second half of the
function which calls SCSI API (scsi_add_device/scsi_remove_device)
should be out of reset_mutex to avoid deadlock between scsi_eh thread
and driver.
During chip reset (inside OCR function), there should not be any PCI
access and AEN function (which is called in delayed context) may be
firing DCMDs (doing PCI writes) when chip reset is happening in parallel
which will cause FW fault. This patch will solve the problem by making
AEN thread and OCR thread mutually exclusive.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shivasharan S