The PCI part of the DesignWare I2C driver does a lot of things that are not
required anymore. For example drivers aren't supposed to handle PCI state
transitions themselves. This is all provided by the PCI bus core already.
In addition to that there is no point scheduling RPM suspend on driver's
idle hook but instead we can use RPM autosuspend for this (which is enabled
in the driver already).
As a bonus, this patch also fixes following compile warning which is
emitted when the driver was compiled without CONFIG_PM_RUNTIME set:
drivers/i2c/busses/i2c-designware-pcidrv.c:245:12: warning: ‘i2c_dw_pci_runtime_idle’ defined but not used [-Wunused-function]
Reported-by: xinhui.pan <xinhuix.pan@intel.com>
Reported-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch allows to set independantly SCL and SDA falling times.
The tLOW period is computed by taking into account the SCL falling time.
The tHIGH period is computed by taking into account the SDA falling time.
For instance in case the margin on tLOW is considered too small, it can
be increased by increasing the SCL falling time which is by default set
at 300ns.
The same applies for tHIGH period with the help of SDA falling time.
Signed-off-by: Romain Baeriswyl <romainba@abilis.com>
Reviewed-by: Christian Ruppert <christian.ruppert@abilis.com>
Acked-by: Shinya Kuribayashi <skuribay@pobox.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Put necessary SSYNC code into blackfin twi arch header. The generic TWI
driver should not contain any architecture specific code.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The ADI TWI peripheral is not binding to the Blackfin processor only.
The bits macros and structs should be put in the generic include header.
And update head file path in drivers accordingly.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Allwinner A31 I2C controller is almost identical to the one used in the
other Allwinner SoCs, except for the fact that it needs to clear the interrupt
by setting the INT_FLAGS bit in the control register, instead of clearing it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Allwinner A31 SoC using that IP has a reset controller maintaining
it reset unless told otherwise.
Add some optional reset support to the driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We should never be busy performing transfers at suspend late, thus
there are no reason to check for it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
At system suspend_late, runtime PM has been disabled by the PM core
which means we can safely operate on these resources. Consequentially
we no longer have to wait until the noirq phase of the system suspend.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since the runtime PM state is expected to be active according to the
amba bus, we must align our behaviour while probing to it.
Moreover, this is needed to be able to have the driver fully functional
without depending on CONFIG_RUNTIME_PM.
Since the device is active while a successful probe has been completed,
the reference counting for the clock will be screwed up and never reach
zero. We resolve this by implementing runtime PM callbacks and let them
handle the resources accordingly, including the clock.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[wsa: s/#if/#ifdef/]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The amba bus are responsible for pm_runtime_enable|disable, remove the
redundant pm_runtime_disable at driver removal.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use devm_* functions to simplify code and error handling.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move the former platform data struct nmk_i2c_controller into the
per-device state container struct i2c_nmk_client, and remove all
the platform data probe path hacks.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[wsa: use 100kHz as default]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
While we are here, also brush up the devicetree binding documentation.
The example was an inappropriate copy from the sh_mobile driver.
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Because the offload mechanism can fall back to a standard transfer,
having two seperate initialization states is unfortunate. Let's just
have one state which does things consistently. This fixes a bug where
some preparation was missing when the fallback happened. And it makes
the code much easier to follow. To implement this, we put the check
if offload is possible at the top of the offload setup function.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: stable@vger.kernel.org # v3.12+
Fixes: 930ab3d403 (i2c: mv64xxx: Add I2C Transaction Generator support)
Pull more i2c updates from Wolfram Sang:
"Mostly bugfixes, small but wanted cleanups, and Paul's init.h removal
applied"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: rcar: fix NACK error code
i2c: update i2c_algorithm documentation
i2c: rcar: use devm_clk_get to ensure clock is properly ref-counted
i2c: rcar: do not print error if device nacks transfer
i2c: rely on driver core when sanitizing devices
i2c: delete non-required instances of include <linux/init.h>
i2c: acorn: is tristate and should use module.h
i2c: piix4: Standardize log messages
i2c: piix4: Use different message for AMD Auxiliary SMBus Controller
i2c: piix4: Add support for AMD ML and CZ SMBus changes
Pull hwmon updates from Jean Delvare:
"This include it87 driver improvements, and a tree-wide change of my
e-mail address"
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
Update Jean Delvare's e-mail address
hwmon: (it87) Print proper names for the IT8771E and IT8772E
hwmon: (it87) Add support for the ITE IT8603E
The response to a bus NACK is to return -ENXIO instead of the
-EREMOTEIO being currently returned by the driver.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The current i2c-rcar driver does clk_get() without a corresponding
clk_put(). Add the clk to the driver private data and then get it
with the devm functions so that it is released when the driver is
unbound.
Note, we do not call clk_prepare_enable() at this point due to the
very possible magic that is being done by the pm_runtime system
underneath the driver.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c-rcar driver currently prints an error message if the master_xfer
callback fails. However if the bus is being probed then lots of NAKs
will be generated, causing the output of a number of errors printed.
To solve this, disable the print if the error is not -EREMOTEIO.
An example of running i2cdetect:
10: i2c-rcar e6530000.i2c: error -121 : 15
-- i2c-rcar e6530000.i2c: error -121 : 15
-- 12 i2c-rcar e6530000.i2c: error -121 : 15
-- i2c-rcar e6530000.i2c: error -121 : 15
-- i2c-rcar e6530000.i2c: error -121 : 15
-- i2c-rcar e6530000.i2c: error -121 : 15
-- i2c-rcar e6530000.i2c: error -121 : 15
-- i2c-rcar e6530000.i2c: error -121 : 15
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This file is controlled by a tristate Kconfig option, and hence
needs to include module.h so that it can get module_init() once
we relocate it from init.h into module.h in the future.
Note that module_exit() appears to be missing from the driver, so
it is questionable whether it would actually work for a removal
and reload cycle if it was configured for a modular build.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use exactly the same log messages in the legacy setup function and the
SB800+ setup function. This way strings can be reused, which saves
some bytes in the generated binary.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Same messages for AMD main and auxiliary SMBus controllers lead to confusion,
this patch is to remove confusion and keep consistent with non-AMD products.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The locations of SMBus register base address and enablement bit are changed
from AMD ML, which need this patch to be supported.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@vger.kernel.org
This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep it
strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared with Mike
Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for multiplatform
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3CcT
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep
it strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared
with Mike Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for
multiplatform"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: mvebu: move Armada 370/XP specific definitions to armada-370-xp.h
ARM: mvebu: remove prototypes of non-existing functions from common.h
ARM: mvebu: move ARMADA_XP_MAX_CPUS to armada-370-xp.h
serial: sh-sci: Rework baud rate calculation
serial: sh-sci: Compute overrun_bit without using baud rate algo
serial: sh-sci: Remove unused GPIO request code
serial: sh-sci: Move overrun_bit and error_mask fields out of pdata
serial: sh-sci: Support resources passed through platform resources
serial: sh-sci: Don't check IRQ in verify port operation
serial: sh-sci: Set the UPF_FIXED_PORT flag
serial: sh-sci: Remove duplicate interrupt check in verify port op
serial: sh-sci: Simplify baud rate calculation algorithms
serial: sh-sci: Remove baud rate calculation algorithm 5
serial: sh-sci: Sort headers alphabetically
ARM: EXYNOS: Kill exynos_pm_late_initcall()
ARM: EXYNOS: Consolidate selection of PM_GENERIC_DOMAINS for Exynos4
ARM: at91: switch Calao QIL-A9260 board to DT
clk: at91: fix pmc_clk_ids data type attriubte
PM / devfreq: use inclusion <mach/map.h> instead of <plat/map-s5p.h>
ARM: EXYNOS: remove <mach/regs-clock.h> for exynos
...
As usual, we have a batch of fixes that weren't considered significant
enough to warrant going into the later -rcs for previous release, so
they are queued up on this branch.
A handful of these are for various DT fixups for Samsung platforms,
and a handful of other minor things.
There are also a couple of stable-marked patches for mvebu -- they came in
quite late and we decided to keep them deferred until the first -stable
release to get more coverage instead of squeezing them into 3.13.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=QhN9
-----END PGP SIGNATURE-----
Merge tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-critical fixes from Olof Johansson:
"As usual, we have a batch of fixes that weren't considered significant
enough to warrant going into the later -rcs for previous release, so
they are queued up on this branch.
A handful of these are for various DT fixups for Samsung platforms,
and a handful of other minor things.
There are also a couple of stable-marked patches for mvebu -- they
came in quite late and we decided to keep them deferred until the
first -stable release to get more coverage instead of squeezing them
into 3.13"
* tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
ARM: at91: smc: bug fix in sam9_smc_cs_read()
i2c: mv64xxx: Document the newly introduced Armada XP A0 compatible
i2c: mv64xxx: Fix bus hang on A0 version of the Armada XP SoCs
ARM: mvebu: Add quirk for i2c for the OpenBlocks AX3-4 board
ARM: mvebu: Add support to get the ID and the revision of a SoC
ARM: dts: msm: Fix gpio interrupt and reg length
irqchip: sirf: set IRQ_LEVEL status_flags
ARM: OMAP2+: gpmc: Move legacy GPMC width setting
ARM: OMAP2+: gpmc: Introduce gpmc_set_legacy()
ARM: OMAP2+: gpmc: Move initialization outside the gpmc_t condition
ARM: OMAP2+: board-generic: update SoC compatibility strings
Documentation: dt: OMAP: explicitly state SoC compatible strings
ARM: OMAP2+: enable AM33xx SOC EVM audio
ARM: OMAP2+: Select USB PHY for AM335x SoC
ARM: bcm2835: Fix grammar in help message
ARM: msm: trout: fix uninit var warning
ARM: dts: Use MSHC controller for eMMC memory for exynos4412-trats2
ARM: dts: Fix definition of MSHC device tree nodes for exynos4x12
ARM: dts: add clock provider for mshc node for Exynos4412 SOC
clk: samsung: exynos4: Fix definition of div_mmc_pre4 divider
...
Pull trivial tree updates from Jiri Kosina:
"Usual rocket science stuff from trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
neighbour.h: fix comment
sched: Fix warning on make htmldocs caused by wait.h
slab: struct kmem_cache is protected by slab_mutex
doc: Fix typo in USB Gadget Documentation
of/Kconfig: Spelling s/one/once/
mkregtable: Fix sscanf handling
lp5523, lp8501: comment improvements
thermal: rcar: comment spelling
treewide: fix comments and printk msgs
IXP4xx: remove '1 &&' from a condition check in ixp4xx_restart()
Documentation: update /proc/uptime field description
Documentation: Fix size parameter for snprintf
arm: fix comment header and macro name
asm-generic: uaccess: Spelling s/a ny/any/
mtd: onenand: fix comment header
doc: driver-model/platform.txt: fix a typo
drivers: fix typo in DEVTMPFS_MOUNT Kconfig help text
doc: Fix typo (acces_process_vm -> access_process_vm)
treewide: Fix typos in printk
drivers/gpu/drm/qxl/Kconfig: reformat the help text
...
If used 64 bit compiler GCC warns that:
drivers/i2c/busses/i2c-s3c2410.c: In function ‘s3c24xx_get_device_quirks’:
drivers/i2c/busses/i2c-s3c2410.c:168:10: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
This patch fixes this by converting "unsigned int" to "kernel_ulong_t".
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use devm_*() functions to make cleanup paths simpler,
and remove redundant return value check of platform_get_resource()
because the value is checked by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- mvebu
- fix boot hang on Armada XP due to broken i2c offloading in A0 SoC revision
(specifically experienced on some early OpenBlocks AX3-4 boards)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=tliU
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-3.13' of git://git.infradead.org/linux-mvebu into next/fixes-non-critical
From Jason Cooper:
mvebu late fixes for v3.13
- mvebu
- fix boot hang on Armada XP due to broken i2c offloading in A0 SoC revision
(specifically experienced on some early OpenBlocks AX3-4 boards)
* tag 'mvebu-fixes-3.13' of git://git.infradead.org/linux-mvebu:
i2c: mv64xxx: Document the newly introduced Armada XP A0 compatible
i2c: mv64xxx: Fix bus hang on A0 version of the Armada XP SoCs
ARM: mvebu: Add quirk for i2c for the OpenBlocks AX3-4 board
ARM: mvebu: Add support to get the ID and the revision of a SoC
Signed-off-by: Kevin Hilman <khilman@linaro.org>
The first variants of Armada XP SoCs (A0 stepping) have issues related
to the i2c controller which prevent to use the offload mechanism and
lead to a kernel hang during boot.
The commit introduces a new the compatible string
marvell,mv78230-a0-i2c for the i2c controller. When this compatible
string is used the driver disables the offload mechanism and the
kernel no more hangs on these SoCs.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reported-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: stable@vger.kernel.org # v3.12+: af8d1c63afcb: ARM: mvebu: Add support to get the ID and the revision of a SoC
Cc: stable@vger.kernel.org # v3.12+: 85e618a1be2b: ARM: mvebu: Add quirk for i2c for the OpenBlocks AX3-4 board
Cc: stable@vger.kernel.org # v3.12+
Fixes: 930ab3d403 (i2c: mv64xxx: Add I2C Transaction Generator support)
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds the support of the I2C_SMBUS_I2C_BLOCK_DATA transaction
type for the iSMT SMBus Controller.
Signed-off-by: Robert Valiquette <robert.valiquette@intel.com>
Acked-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
OSIF, Open Source InterFace, is a USB based i2c bus master. The
origional design was based on i2c-tiny-usb, but more modern versions
of the firmware running on the MegaAVR microcontroller use a different
protocol over the USB. This code is based on Barry Carter
<barry.carter@gmail.com> driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The RobotFuzz device is not compatible with i2c-tiny-usb. Remove its
entry from the USB table so that the new correct driver can be used.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since 93abe8e4 (clk: add non CONFIG_HAVE_CLK routines) code using clk.h
like this platform driver need not depend on HAVE_CLK. Also, remove a
redundant clk.h include from core driver.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Nomadik I2C is now configured from the device tree on all platforms
using this controller. Delete the platform data header and move the
definitions into the driver so it is all contained in one single file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Nomadik I2C controller needs to have the slave set-up time
configured based off the clock used to drive the I2C bus block.
Currently this is done with static assignments assuming that the
block is clocked 48MHz which is pretty likely to be bug-prone.
Calculate the SLSU from the equation given in the datasheet
instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
cppcheck rightfully says:
drivers/i2c/busses/i2c-viperboard.c:169: style: Variable 'bytes_xfer' is assigned a value that is never used.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Lars Poeschel <poeschel@lemonage.de>
This patch fixed several typo in printk from various
part of kernel source.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Simplified the probe and remove functions using devm_* functions
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
IRQ handler has to be register first before IRQ
is enabled in xiic_reinit().
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Code changes to fix checkpatch warnings listed below.
- WARNING: please, no space before tabs
- WARNING: quoted string split across lines
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use devm_request_region() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use devm_kzalloc() functions to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
smatch rightfully says:
drivers/i2c/busses/i2c-imx.c:610 i2c_imx_probe() info: why not propagate 'irq' from platform_get_irq() instead of (-2)?
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For Exynos4 and Exynos5 SoCs from Samsung the i2c clock is based
on a fixed 66 MHz peripheral clock, and therefore is completely
independent of the cpu frequency.
Thus, registering for a CPU freq notifier is very wasteful.
This patch modifes the code such that, i2c bus registers to
cpu_freq_transition only if CONFIG_CPU_FREQ_S3C24XX is enabled.
This change should save a bunch of cpufreq transitions calls
which does not apply to exynos SoCs.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds polling mode support for i2c-s3c2410 driver.The
SATA PHY controller's CMU and TRSV block's are of I2C register
map in exynos5250.These blocks can be configured using i2c.
But i2c controller instance on which these block's sits lacks an
interrupt line.Also the current i2c-s3c2410 driver is only interrupt
driven, thus a polling mode support is required in the driver for
supporting this controller. This patch adds this support to the driver.
Signed-off-by: Vasanth Ananthan <vasanth.a@samsung.com>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Hardware supported by the i2c sh_mobile and rcar drivers is only found
on SUPERH or ARCH_SHMOBILE platforms. Restrict non-COMPILE_TEST
compilation to them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested with a r7s72100 genmai board acessing an eeprom.
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJSr3AnAAoJEMzrak5tbycxfMwQAMeffTFreJqDiQ4Vj0XmuhSn
RFlXiZQsWtQ6gGgNfKyDsXzDMaz1KDAabcUYRcZwrluxuSCPBcK1JirCj5R8uRY7
LDZFX92CO8zRgiij0mhgokV4zzuEQ56q1uhPxqI3o+wG3v44jlMSMgFHQJUevdET
aKr2Pss8Hb00XDztnpxprs6FUoU/W99NRH0i/5znbBwuHqYFP37zlKe2MRwbqDwR
AMgkrnGoawe85Stz4p/iR9pCLpAMa0dH94V4JrAP4+IQrl0DEKWbrolpQHii4gzh
NCGazMELTqkaZaorC/n1SmczH1kTj4vcjbbmeB8dwS8Vqhr+uf7W1oLlJ46TUOsp
ESO0uD2GfpHKQQwLxEfgjfmwsIUMbdWHef8f2HUuvl6Js+LCpaPkxd52Pt/qL4sU
0sKqTbldRZXzGhvwa0/MK32WhmH4v31s7IZAg5A2YxqDR6yWryl7legWyvrI96C0
OlmVe1C/2NGk0QCfK0G/xTa9V7YzMfj8k4ICSZOgUoF4BeGGj6d3svWvLbKbbrU1
0fVvR7aCm78pRXixI6kURpj9D0mEfqus9Hx7VoWcL0TS4QH2dSYlGI+jDCiliQmj
+kWrZWHsASSvPmUZk4RBNaviCbnGU8/t5nNdJSdFIUM/PIswzZ4GaAu6gdVksIY8
hcx410PyAzTZL2lENamE
=8T7+
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/cleanup
From Stephen Warren:
ARM: tegra: implement common DMA and resets DT bindings
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
* tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (30 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Correct spelling typo in various part of kernel
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tegra's clock driver now provides an implementation of the common
reset API (include/linux/reset.h). Use this instead of the old Tegra-
specific API; that will soon be removed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Pull i2c fixes from Wolfram Sang:
"Some easy but needed fixes for i2c drivers since rc1"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: bcm2835: Linking platform nodes to adapter nodes
i2c: omap: raw read and write endian fix
i2c: i2c-bcm-kona: Fix module build
i2c: i2c-diolan-u2c: different usb endpoints for DLN-2-U2C
i2c: bcm-kona: remove duplicated include
i2c: davinci: raw read and write endian fix
In order to find I2C devices in the device tree, the platform nodes
have to be known by the I2C core. This requires setting the
dev.of_node parameter of the adapter.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
All OMAP IP blocks expect LE data, but CPU may operate in BE mode.
Need to use endian neutral functions to read/write h/w registers.
I.e instead of __raw_read[lw] and __raw_write[lw] functions code
need to use read[lw]_relaxed and write[lw]_relaxed functions.
If the first simply reads/writes register, the second will byteswap
it if host operates in BE mode.
Changes are trivial sed like replacement of __raw_xxx functions
with xxx_relaxed variant.
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Correct a typo that prevented the driver from being built as a module.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The previous diolan adapter uses other out/in endpoints than
the current DLN-2-U2C in compatibility mode.
They changed from 0x2/0x84 to 0x3/0x83.
This patch gets the endpoints from the usb interface, instead
of hardcode them in the driver.
This was tested on a current DLN-2-U2C board.
Signed-off-by: Martin Vogt <mvogt1@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C IP block expect LE data, but CPU may operate in BE mode.
Need to use endian neutral functions to read/write h/w registers.
I.e instead of __raw_read[lw] and __raw_write[lw] functions code
need to use read[lw]_relaxed and write[lw]_relaxed functions.
If the first simply reads/writes register, the second will byteswap
it if host operates in BE mode.
Changes are trivial sed like replacement of __raw_xxx functions
with xxx_relaxed variant.
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
From Tony Lindgren:
Few more fixes for issues found booting older omaps using device tree.
Also few randconfig build fixes and removal of some dead code for omap4
as it no longer has legacy platform data based booting support.
* tag 'omap-for-v3.13/more-fixes-for-merge-window-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove legacy omap4_twl6030_hsmmc_init
ARM: OMAP2+: Remove legacy mux code for display.c
ARM: OMAP2+: Fix undefined reference to set_cntfreq
gpio: twl4030: Fix passing of pdata in the device tree case
gpio: twl4030: Fix regression for twl gpio output
ARM: OMAP2+: More randconfig fixes for reconfigure_io_chain
ARM: dts: Fix omap2 specific dtsi files by adding the missing entries
ARM: OMAP2+: Fix GPMC and simplify bootloader timings for 8250 and smc91x
i2c: omap: Fix missing device tree flags for omap2
Pull i2c changes from Wolfram Sang:
- new drivers for exynos5, bcm kona, and st micro
- bigger overhauls for drivers mxs and rcar
- typical driver bugfixes, cleanups, improvements
- got rid of the superfluous 'driver' member in i2c_client struct This
touches a few drivers in other subsystems. All acked.
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
i2c: bcm-kona: fix error return code in bcm_kona_i2c_probe()
i2c: i2c-eg20t: do not print error message in syslog if no ACK received
i2c: bcm-kona: Introduce Broadcom I2C Driver
i2c: cbus-gpio: Fix device tree binding
i2c: wmt: add missing clk_disable_unprepare() on error
i2c: designware: add new ACPI IDs
i2c: i801: Add Device IDs for Intel Wildcat Point-LP PCH
i2c: exynos5: Remove incorrect clk_disable_unprepare
i2c: i2c-st: Add ST I2C controller
i2c: exynos5: add High Speed I2C controller driver
i2c: rcar: fixup rcar type naming
i2c: scmi: remove some bogus NULL checks
i2c: sh_mobile & rcar: Enable the driver on all ARM platforms
i2c: sh_mobile: Convert to clk_prepare/unprepare
i2c: mux: gpio: use reg value for i2c_add_mux_adapter
i2c: mux: gpio: use gpio_set_value_cansleep()
i2c: Include linux/of.h header
i2c: mxs: Fix PIO mode on i.MX23
i2c: mxs: Rework the PIO mode operation
i2c: mxs: distinguish i.MX23 and i.MX28 based I2C controller
...
Fix to return a negative error code from the bus speed parse
error handling case instead of 0.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Using the i2c-eg20t driver and call i2cdetect or probe on the bus,
the driver will print a lot of error messages if there was no ACK
received.
i2cdetect normally print a table with all the available devices. If there
is no device on the address, the table will be empty.
Currently with the i2c-eg20t driver, the table is not visible because
the error messages destroy the table.
Error message: pch_i2c_getack return -71
This patch prevent the driver to print the messages to syslog.
The pch_i2c_wait_for_check_xfer function is the only one who is
calling pch_i2c_getack, so we can delete the function and add the
read to pch_i2c_wait_for_check_xfer.
If no ACK is received, the Message will be printed as a dbg
message.
Fixed print message to be a one liner so we can grep for the
error message.
Tested on Intel Atom E6xx and Eg20t Chipset.
Signed-off-by: Andreas Werner <wernerandy@gmx.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Introduce support for Broadcom Serial Controller (BSC) I2C bus found
in the Kona family of Mobile SoCs. FIFO hardware is utilized but only
standard mode (100kHz), fast mode (400kHz), fast mode plus (1MHz), and
I2C high-speed (3.4 MHz) bus speeds are supported.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
[wsa: fixed Kconfig sorting, squashed broken out patches into one]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
As we claim to support device tree for mach-omap2, we
should have the necessary flags in the driver to make it
usable.
Cc: linux-i2c@vger.kernel.org
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like we're missing two lines needed to make it
work properly with device tree.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the missing clk_disable_unprepare() before return
from wmt_i2c_reset_hardware() in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org # 3.11+
Newer Intel PCHs with LPSS have the same Designware I2C controllers than
Haswell but the ACPI IDs differ. Add these IDs to the driver list.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds the SMBus Device IDs for the Intel Wildcat Point-LP PCH.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds support to SSC (Synchronous Serial Controller)
I2C driver. This IP also supports SPI protocol, but this is not
the aim of this driver.
This IP is embedded in all ST SoCs for Set-top box platorms, and
supports I2C Standard and Fast modes.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Adds support for High Speed I2C driver found in Exynos5 and
later SoCs from Samsung.
Driver only supports Device Tree method.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Taekgyun Ko <taeggyun.ko@samsung.com>
Reviewed-by: Simon Glass <sjg@google.com>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: Andrew Bresticker <abrestic@google.com>
[wsa: rebased to v3.12-rc4 (no of_i2c.h anymore)]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
b720423a26
(i2c: rcar: add rcar-H2 support)
added R-Car H2 support on i2c-rcar.
The R-Car I2C type is based on SoC generation
(Gen1 = E1/M1/H1, Gen2 = E2/M2/H2),
but added naming was H1/H2 instead of Gen1/Gen2.
Gen1/Gen2 is better naming on this driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
"obj" can't be NULL here.
We already know that "pkg->package.elements" gives us a valid pointer
so the next pointer after that is also non-NULL.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Renesas ARM platforms are transitioning from single-platform to
multi-platform kernels using the new ARCH_SHMOBILE_MULTI. Make the
driver available on all ARM platforms to enable it on both ARCH_SHMOBILE
and ARCH_SHMOBILE_MULTI, and increase build testing coverage with
COMPILE_TEST.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Turn clk_enable() and clk_disable() calls into clk_prepare_enable() and
clk_disable_unprepare() to get ready for the migration to the common
clock framework.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Replace some instances of of_irq_map_one()/irq_create_of_mapping() and
of_irq_to_resource() by the simpler equivalent irq_of_parse_and_map().
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
[grant.likely: resolved conflicts with core code renames]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Initially commit cb527ede1b
"i2c-omap: Double clear of ARDY status in IRQ handler"
added a workaround for undocumented errata ProDB0017052.
But then commit 1d7afc9594
"i2c: omap: ack IRQ in parts" refactored code and missed
one of ARDY clearings. So current code violates errata.
It causes often i2c bus timeouts on my Pandaboard.
This patch adds a second clearing in place.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Subsystems like pinctrl and gpio rightfully make use of deferred probing at
core level. Now, deferred drivers won't be retried if they don't have a .probe
function specified in the driver struct. Fix this driver to have that, so the
devices it supports won't get lost in a deferred probe.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Subsystems like pinctrl and gpio rightfully make use of deferred probing at
core level. Now, deferred drivers won't be retried if they don't have a .probe
function specified in the driver struct. Fix this driver to have that, so the
devices it supports won't get lost in a deferred probe.
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Subsystems like pinctrl and gpio rightfully make use of deferred probing at
core level. Now, deferred drivers won't be retried if they don't have a .probe
function specified in the driver struct. Fix this driver to have that, so the
devices it supports won't get lost in a deferred probe.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Subsystems like pinctrl and gpio rightfully make use of deferred probing at
core level. Now, deferred drivers won't be retried if they don't have a .probe
function specified in the driver struct. Fix this driver to have that, so the
devices it supports won't get lost in a deferred probe.
Reported-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
The i.MX23 I2C controller is also capable of PIO, but needs a little harder
push to behave. The controller needs to be reset after every PIO/DMA operation
for some reason, otherwise in rare cases, the controller can hang or emit
bytes onto the bus.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Analyze and rework the PIO mode operation. The PIO mode operation
was unreliable on MX28, by analyzing the bus with LA, the checks
for when data were available or were to be sent were wrong.
The PIO WRITE has to be completely reworked as it multiple problems.
The MX23 datasheet helped here, see comments in the code for details.
The problems boil down to:
- RUN bit in CTRL0 must be set after DATA register was written
- The PIO transfer must be 4 bytes long tops, otherwise use
clock stretching.
Both of these fixes are implemented.
The PIO READ operation can only be done for up to four bytes as
we are unable to read out the data from the DATA register fast
enough.
This patch also tries to document the investigation within the
code.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It seems the PIO mode does not work, or at least not like it works
on a i.MX28. Each short transfer needs about one second (without an
error message) but does not send anything on the I2C lines.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Using the same clock for all device instances is non-portable and obtaining
clock references by an ID without using a device pointer is discouraged.
This is also not needed, because on platforms, where this driver is used,
suitable clocks are available for the I2C controllers, that are children of
the peripheral clock and just pass its rate 1-to-1 to controllers. This
patch switches the driver to obtain references to correct clocks.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When clk_get() fails, it returns an error code, not a NULL. This patch
fixes such an error handling bug.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds Device Tree support to the i2c-rcar driver and respective
documentation.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is no need to repeatedly query clock frequency, where it is not
expected to change. The complete loop can also trivially be replaced with
a simple division. A further loop below the one, being simplified, could
also be replaced, but that would get more complicated.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
A recent patch added even more superfluous parenthesis to those, which
already were there. Remove them again.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds code to initialize the DMA buffer to compensate for
possible hardware data corruption.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
[wsa: changed to use 'sizeof']
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
According to Designware I2C spec, if I2C_DYNAMIC_TAR_UPDATE is set to 1,
the 10-bit addressing mode is controlled by IC_10BITADDR_MASTER bit of
IC_TAR register instead of IC_CON register. The IC_10BITADDR_MASTER
in IC_CON register becomes read-only copy. Since I2C_DYNAMIC_TAR_UPDATE
value can't be detected from hardware register, so we will always set the
IC_10BITADDR_MASTER bit in both IC_CON and IC_TAR register whenever 10-bit
addresing mode is requested by user application.
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver is used on PowerPC which don't provide writel_relaxed(). This
breaks the c2k and prpmc2800 default configurations. To fix the build,
turn the calls to writel_relaxed() into writel(). The impacts for ARM
should be minimal.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some functions and variables are only used if the configuration selects
HAVE_CLK. Protect them with a corresponding #ifdef CONFIG_HAVE_CLK block
to avoid compiler warnings.
Signed-off-by: Thierry Reding <treding@nvidia.com>
[wsa: added marker to #endif]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
commit d16933b339 "i2c: s3c2410: Move
location of clk_prepare_enable() call in probe function" refactored
clk_enable and clk_disable calls yet neglected to remove the
clk_disable_unprepare call in the module's remove().
It helps remove warnings on an arndale during unbind:
echo 12c90000.i2c > /sys/bus/platform/devices/12c90000.i2c/driver/unbind
------------[ cut here ]------------
WARNING: CPU: 0 PID: 2548 at drivers/clk/clk.c:842 clk_disable+0x18/0x24()
Modules linked in:
CPU: 0 PID: 2548 Comm: bash Not tainted 3.11.0-next-20130916-00003-gf4bddbc #6
[<c0014d48>] (unwind_backtrace+0x0/0xf8) from [<c00117d0>] (show_stack+0x10/0x14)
[<c00117d0>] (show_stack+0x10/0x14) from [<c0361be8>] (dump_stack+0x6c/0xac)
[<c0361be8>] (dump_stack+0x6c/0xac) from [<c001d864>] (warn_slowpath_common+0x64/0x88)
[<c001d864>] (warn_slowpath_common+0x64/0x88) from [<c001d8a4>] (warn_slowpath_null+0x1c/0x24)
[<c001d8a4>] (warn_slowpath_null+0x1c/0x24) from [<c02c4a64>] (clk_disable+0x18/0x24)
[<c02c4a64>] (clk_disable+0x18/0x24) from [<c028d0b0>] (s3c24xx_i2c_remove+0x28/0x70)
[<c028d0b0>] (s3c24xx_i2c_remove+0x28/0x70) from [<c0217a10>] (platform_drv_remove+0x18/0x1c)
[<c0217a10>] (platform_drv_remove+0x18/0x1c) from [<c0216358>] (__device_release_driver+0x58/0xb4)
[<c0216358>] (__device_release_driver+0x58/0xb4) from [<c02163d0>] (device_release_driver+0x1c/0x28)
[<c02163d0>] (device_release_driver+0x1c/0x28) from [<c02153c0>] (unbind_store+0x58/0x90)
[<c02153c0>] (unbind_store+0x58/0x90) from [<c0214c90>] (drv_attr_store+0x20/0x2c)
[<c0214c90>] (drv_attr_store+0x20/0x2c) from [<c01032c0>] (sysfs_write_file+0x168/0x198)
[<c01032c0>] (sysfs_write_file+0x168/0x198) from [<c00ae1c0>] (vfs_write+0xb0/0x194)
[<c00ae1c0>] (vfs_write+0xb0/0x194) from [<c00ae594>] (SyS_write+0x3c/0x70)
[<c00ae594>] (SyS_write+0x3c/0x70) from [<c000e3e0>] (ret_fast_syscall+0x0/0x30)
---[ end trace 4c9f9403066f57a6 ]---
------------[ cut here ]------------
WARNING: CPU: 0 PID: 2548 at drivers/clk/clk.c:751 clk_unprepare+0x14/0x1c()
Modules linked in:
CPU: 0 PID: 2548 Comm: bash Tainted: G W 3.11.0-next-20130916-00003-gf4bddbc #6
[<c0014d48>] (unwind_backtrace+0x0/0xf8) from [<c00117d0>] (show_stack+0x10/0x14)
[<c00117d0>] (show_stack+0x10/0x14) from [<c0361be8>] (dump_stack+0x6c/0xac)
[<c0361be8>] (dump_stack+0x6c/0xac) from [<c001d864>] (warn_slowpath_common+0x64/0x88)
[<c001d864>] (warn_slowpath_common+0x64/0x88) from [<c001d8a4>] (warn_slowpath_null+0x1c/0x24)
[<c001d8a4>] (warn_slowpath_null+0x1c/0x24) from [<c02c5834>] (clk_unprepare+0x14/0x1c)
[<c02c5834>] (clk_unprepare+0x14/0x1c) from [<c028d0b8>] (s3c24xx_i2c_remove+0x30/0x70)
[<c028d0b8>] (s3c24xx_i2c_remove+0x30/0x70) from [<c0217a10>] (platform_drv_remove+0x18/0x1c)
[<c0217a10>] (platform_drv_remove+0x18/0x1c) from [<c0216358>] (__device_release_driver+0x58/0xb4)
[<c0216358>] (__device_release_driver+0x58/0xb4) from [<c02163d0>] (device_release_driver+0x1c/0x28)
[<c02163d0>] (device_release_driver+0x1c/0x28) from [<c02153c0>] (unbind_store+0x58/0x90)
[<c02153c0>] (unbind_store+0x58/0x90) from [<c0214c90>] (drv_attr_store+0x20/0x2c)
[<c0214c90>] (drv_attr_store+0x20/0x2c) from [<c01032c0>] (sysfs_write_file+0x168/0x198)
[<c01032c0>] (sysfs_write_file+0x168/0x198) from [<c00ae1c0>] (vfs_write+0xb0/0x194)
[<c00ae1c0>] (vfs_write+0xb0/0x194) from [<c00ae594>] (SyS_write+0x3c/0x70)
[<c00ae594>] (SyS_write+0x3c/0x70) from [<c000e3e0>] (ret_fast_syscall+0x0/0x30)
---[ end trace 4c9f9403066f57a7 ]---
Signed-off-by: Kim Phillips <kim.phillips@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
commit 6d4028c644 (i2c: use dev_get_platdata()) did a bad conversion
of this one case:
drivers/i2c/busses/i2c-davinci.c: In function 'davinci_i2c_probe':
drivers/i2c/busses/i2c-davinci.c:665:2: warning: passing argument 1 of
'dev_get_platdata' from incompatible pointer type [enabled by default]
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch modify I2C driver of rcar-H1 to usable on both rcar-H1 and rcar-H2.
Signed-off-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
let i2c core retry 3 times as sometimes we get random noack and timeout
even when we access an existing i2c client.
Signed-off-by: Zhiwu Song <Zhiwu.Song@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
if users set I2C_M_REV_DIR_ADDR, revert the direction of address.
Signed-off-by: Zhiwu Song <Zhiwu.Song@csr.com>
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
there is a typo before, it makes the final bitrate wrong, this patch fixes
it.
Signed-off-by: Zhiwu Song <Zhiwu.Song@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
this fixes the issue that we lost to wait the i2c reset finished.
Signed-off-by: Zhiwu Song <Zhiwu.Song@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Due to hardware ANOMALY, we need to reset I2C earlier after
we get NOACK while accessing non-existing clients, otherwise
we will get errors even we access existing clients later
Signed-off-by: Zhiwu Song <Zhiwu.Song@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some Intel LPSS I2C devices make the SDA hold time and *CNT parameters
available via SSCN (standard mode) and FMCN (fast mode) ACPI methods.
Implement support for this so that we check whether an ACPI method exists
and if it does, fill in the SDA hold time and *CNT values to the device
private structure for core to use.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The DesignWare I2C controller has high count (HCNT) and low count (LCNT)
registers for each of the I2C speed modes (standard and fast). These
registers are programmed based on the input clock speed in the driver.
The current code calculates these values based on the input clock speed and
tries hard to meet the I2C bus timing requirements. This could result
non-optimal values with regarding to the bus speed. For example on Intel
BayTrail we get bus speed of 315.41kHz which is ~20% slower than we would
expect (400kHz) in fast mode (even though the timing requirements are met).
This patch makes it possible for the platform code to pass more optimal
HCNT/LCNT values to the core driver if they are known beforehand. If these
are not set we use the calculated and more conservative values.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Shinya Kuribayashi <skuribay@pobox.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
make the MPC I2C driver get, prepare and enable the gated clock item for
register access during probe; disable and unprepare the clock upon
remove(), put is done by the devm approach; hold a reference to the
clock over the period of use
clock lookup is non-fatal in this implementation as not all platforms
may provide clock specs in their device tree, but failure to enable a
clock when specified is considered fatal
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix to return a negative error code in the irq get error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
[wsa: fixed wrong exit point, too]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This follows what has already been done for the DeviceTree helpers. Move
the ACPI helpers from drivers/acpi/acpi_i2c.c to the I2C core and update
documentation accordingly.
This also solves a problem reported by Jerry Snitselaar that we can't build
the ACPI I2C helpers as a module.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C of helpers used to live in of_i2c.c but experience (from SPI) shows
that it is much cleaner to have this in the core. This also removes a
circular dependency between the helpers and the core, and so we can
finally register child nodes in the core instead of doing this manually
in each driver. So, fix the drivers and documentation, too.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
All the Armada XP (mv78230, mv78260 and mv78460) have a silicon issue
in the I2C controller which violate the i2c repeated start
timing. The I2C standard requires a minimum of 4.7us for the repeated
start condition whereas the I2C controller of the Armada XP this time
is 2.9us.
So this patch adds a 5us delay for the start case only if the
the compatible i2c-mv78230 is set.
Based on the initals patches from Zbigniew Bodek
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Zbigniew Bodek <zbb@semihalf.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The I2C Transaction Generator offloads CPU from managing I2C
transfer step by step.
This feature is currently only available on Armada XP, so usage of
this mechanism is activated through device tree.
Based on the work of Piotr Ziecik and rewrote to use the new way of
handling multiples i2c messages.
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We want to bail out immediately if i2c_add_adapter failed and not try to
register child nodes with a nilled adapter structure.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Patch fixes i2c-tiny-usb not to use stack as URB transfer_buffer. URB buffers
need to be DMA-able, which stack is not.
Patch is only compile tested.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
According to I2C specification the NACK should be handled as folowing:
"When SDA remains HIGH during this ninth clock pulse, this is defined as the Not
Acknowledge signal. The master can then gene rate either a STOP condition to
abort the transfer, or a repeated START condition to start a new transfer."
[http://www.nxp.com/documents/user_manual/UM10204.pdf]
The same is recomened by TI I2C wiki:
http://processors.wiki.ti.com/index.php/I2C_Tips
Currently, the OMAP I2C driver interrupts I2C trunsfer in case of NACK, but
It queries Stop condition OMAP_I2C_CON_REG.STP=1 only if NACK has been received
during the last message transmitting/recieving.
This may lead to stuck Bus in "Bus Busy" until I2C IP reset (idle/enable).
Hence, fix it by querying Stop condition (STP) always when NACK is received.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Hein Tibosch <hein_tibosch@yahoo.es>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The timing calculation is rather bogus and gives extremely wrong
results for higher frequencies (on an i.MX28). E.g. instead of 400 kHz
I measured 770 kHz.
Implement a calculation that adheres to the I2C spec and gives exact
results for I2C frequencies from 12.56 kHz to 960 kHz.
Also the bus_free and leadin parameters are programmed according to
the I2C spec for standard and fast mode.
This was tested on a Ka-Ro TX28 module with a DS1339, TSC2007, PCA9554
and SGTL5000 client.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Marek Vasut <marex@denx.de>
[wsa: patch fixes whitespace issue, too]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to devm_ioremap_resource.
Move the call to platform_get_resource adjacent to the call to
devm_ioremap_resource to make the connection between them more clear.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@
- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add Freescale Vybrid VF610 I2C controller support to
imx I2C driver framework.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This add struct imx_i2c_hwdata to hold more quirks data
which may vary between SoCs, thus the driver can operate
on more differences to support more SoCs.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This add bits operation macro that differ between SoCs.
Interrupt flags clear operation in I2SR differ between SoCs:
write zero to clear(w0c) INT flag on i.MX,
but write one to clear(w1c) INT flag on Vybrid.
I2C module enable operation in I2CR also differ between SoCs:
set I2CR_IEN bit enable the module on i.MX,
but clear I2CR_IEN bit enable the module on Vybrid.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
the I2C register offset may different between SoCs,
to provid support for all these chips, split the
register offset into a fixed base address and a
variable shift value, then the full register offset
will be calculated by
reg_off = ( reg_base_addr << reg_shift)
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
wrap the readb(), writeb() into inline function calls.
It would make the driver more clearer to support platform
with different register offset.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The id_entry field should be changed by platform driver core,
driver should prevent changing it derectly. Use local variable
to save and extract platform_device_id info of the dts devices
instead.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The module clk should be enabled before write to
its register in probe(), and the clk can be disabled
after.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
using struct representing the i2c clk{div, val} pair would
make the i2c_clk_div array more clear.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for the secondary SMBus controller on the AMD SB800 and AMD FCH
chipsets.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Tested-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Keystone SOCs uses the same I2C IP as available on DaVinci SOCs.
Update the config so that ARCH_KEYSTONE can use it.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver no longer uses definitions from mach/hardware.h.
On the other hand, including this header breaks this driver
on non-davinci platforms which don't have such a header.
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.
drivers/i2c/busses/i2c-bfin-twi.c:585:12: warning: 'i2c_bfin_twi_suspend' defined but not used [-Wunused-function]
drivers/i2c/busses/i2c-bfin-twi.c:600:12: warning: 'i2c_bfin_twi_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add CONFIG_PM_SLEEP to suspend function to fix the following build
warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.
drivers/i2c/busses/i2c-puv3.c:249:12: warning: 'puv3_i2c_suspend' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Mika Westerberg