mac80211 supports multiple virtual interfaces for a single device. For
example, a managed interface (wlan0) and a monitor interface (mon0) can
exist at the same time. Thus priv->iw_mode is not sufficient to track
the wireless mode any more. The patch redefines priv->iw_mode as the
first interface mode (the same as priv->vif->type if priv->vif != NULL).
If another monitor type interface is created later, we don't change
priv->iw_mode into monitor. This way, the original interface still
works. The patch also requests mac80211 to do reassociation after we
change the Rx filter flags.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes 4965 prefix from comments and one function
in iwl-agn-rs.h
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up FH bits and adds missing register values
that will be used later in TX initialization rewrite
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This implements proper short slot handling and adds code to
program the hardware for the correct response rates derived
from the basic rate set for the current BSS.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds a helper function that, given a bitmap of basic
rates and a bitrate returns the response rate for this rate.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move calculation of CSR register offset into rt2x00debug.c
and remove the wrapper functions from each individual driver.
(Except rt2500usb, which still needs to wrap for the
different value type argument).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath9k/xmit.c: In function ‘ath_tx_start’:
drivers/net/wireless/ath9k/xmit.c:1858: warning: ‘tid’ may be used uninitialized in this function
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The latest vendor driver (rtl8187B_linux_26.1036.0708.2008) has a 10 msec
delay after the call to set a new channel, but not before.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Each of the primary write routines, rtl8187_write_phy(),
rtl8225_write_bitbang(), and rtl8225_write_8051() all conclude with an
msleep() command. Testing shows that these are not needed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Routine rtl8225_write() calls either rtl8225_write_bitbang() or
rtl8225_write_8051(), both of which end with an msleep() command. As a
result, a rtl8225_write() immediately followed by an msleep() is not needed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Routine rtl8225_write_phy_cck() calls rtl8225_write_phy(), which concludes
with a sleep of 1 msec; therefore a call to rtl8225_write_phy_cck()
immediately followed by an msleep(1) is not needed.
Signed-off-by: Larry Finger <Larry.Finger@larry.finger>
Tested-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Routine rtl8225_write_phy_ofdm() calls rtl8225_write_phy(), which concludes
with a sleep of 1 msec; therefore a call to rtl8225_write_phy_ofdm()
immediately followed by an msleep(1) is not needed.
Signed-off-by: Larry Finger <Larry.Finger@larry.finger>
Tested-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rtl8187 driver contains 3 sleep statements that are longer than
a second. Testing has shown no bad effects when they are removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All operating modes which require beaconing should
depend on the availability of beacon entries from
the hardware.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can safely remove ieee80211_bss_conf from rt2x00_intf,
it is provided by mac80211 in ieee80211_vif as well.
(rt2x00_intf is the drv_priv field of ieee80211_vif).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement latest changed from mac80211 configuration
handling to optmize configuration handling in rt2x00.
* Remove set_retry_limit callback function, handled
through config()
* Move config_antenna to its own callback function,
it isn't handled by mac80211 anymore
* Use IEEE80211_CONF_CHANGED_* flags and remove manual
checks
* Removed deprecated short slot setting through config()
and put it in config_erp() through which mac80211 now
configures it
* Remove config_phymode() and move contents to config_erp()
since it only managed the basic rates which is now
determined by mac80211 through config_erp().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Newer parts have slots at entry+64 for michael mic and can do WPA-TKIP
in hardware. The open-sourced Atheros HAL has code for accessing this
portion so now we know how where to put the key material.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change re-enables hardware encryption for ath5k after setting up
mac80211 to handle the initialization vectors which happens to make it
work. Add a module param (nohwcrypt) to optionally turn it off.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes two current compilation problems. They showed up
with CONFIG_IEEE80211_DEBUG defined.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Send a notification to the driver on succesful
reception of an ADDBA response, add IEEE80211_AMPDU_TX_RESUME
for this purpose.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 has RX A-MPDU reordering support.
Use that and remove redundant RX processing within the driver.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Doing an interface down/up leaves the old HT assoc
information, clear it.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Accessing mac80211's internal state machine is wrong.
Will add resumption of a TID in a later patch.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
config_interface() was the wrong place to enable interrupts
when bringing up an interface, move it to ath_open().
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TSF is already reset properly via mac80211's callback.
Resetting it in config_interface() is not needed.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simplify attach and detach routines by consolidating
the stop and suspend functions.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split hw.c into more manageable files:
ani.c
calib.c
eeprom.c
mac.c
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the internal VAP management routines
and embed ath_vap in mac80211's driver private area
provided in ieee80211_vif.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also, random indentation and whitespace cleanup.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the ath_buf instance associated with each tx frame
directly and remove all redundant information in ath_tx_control.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Start removing the internal node list in ath9k, in preparation
for using mac80211's STA list.
Remove lists, locks, routines, flags, functions managing nodes in ath9k.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Be sure we clear out both the mic (if applicable) and
the encryption key type.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* In set_opmode don't handle antenna settings and preserve other STA_ID1 settings
(shouldn't matter because we call it during reset but it makes things cleaner)
Also set properly AP/ADHOC indicator flag on CFG while setting AP/ADHOC modes
and always enable key search mode.
* Properly set BSSID Mask during reset (cache it and reuse it durring set_associd)
* Update beacon_init to flush pending BMISS interrupts and handle setting of adhoc
beacon ATIM policy flag for ad-hoc mode. Also set TSF to 0 to start TSF increment
on AP mode. We need to handle sleep timers for AR5212 there + add support for PCF.
* Properly clean MIC key from keytable when TKIP is used (Bob is working on set_key
function etc so i leave it for now).
Tested on AR5212 (Hainan) and AR5413 and works fine
v2 Set PISR on AR5211+ and ISR on AR5210, got to sleep more ;-)
Changes-Licensed-under: ISC
Signed-Off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert all the drivers using net/ieee80211.h to use linux/ieee80211.h.
Contains a bugfix in libertas where the SSID parsing could overrun the
buffer when the AP sends invalid information.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Dan Williams <dcbw@redhat.com> [airo, libertas]
Acked-by: Pavel Roskin <proski@gnu.org> [orinoco]
Acked-by: David Kilroy <kilroyd@googlemail.com> [orinoco]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I added this comment myself, but it's clearly wrong. I had meant
to place it in iwl_mac_add_interface, which at the time didn't
honour the MAC address setting, but it does now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the SSID from the driver API since now there is no
driver that requires knowing the SSID and I think it's
unlikely that any hardware design that does require the
SSID will play well with mac80211.
This also removes support for setting the SSID in master
mode which will require a patch to hostapd to not try.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since adm8211 currently doesn't implement IBSS mode anyway,
it can't be using the SSID. And if/when it does implement
IBSS mode, we'll have to see how to make it beacon anyway.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SSID programmed into the device is used by the ucode only
to reply to probe requests, a functionality we disable anyway
because it doesn't fit with the mac80211/hostapd programming
model. Therefore, it isn't useful to program the SSID into
device.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now the essid stuff is unused, so remove it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an undirected scan is requested and iwlwifi is not associated but
the user has set an SSID (and maybe was associated with that network at
some point) then iwlwifi will assume the user wanted to scan for this
SSID which seems wrong. Remove this code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Was wondering about this code since supposedly the firmware will
add the SSID element. Turns out it's dead, so remove it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I added .set_frag_threshold I didn't realise it was already
there which now generated a sparse warning. Therefore, remove
the .set_frag_threshold NULL initialiser, and while at it all the
other useless ones.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a constant from the 802.11 specification.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch prints reason code for deauth/dissoc frames to give users
more ideas what's happened for the disconnection.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zhu, Yi