On SAMA7G5, when resuming from backup and self-refresh, the bootloader
performs DDR PHY recalibration by restoring the value of ZQ0SR0 (stored
in RAM by Linux before going to backup and self-refresh). It has been
discovered that the current procedure doesn't work for all possible values
that might go to ZQ0SR0 due to hardware bug. The workaround to this is to
avoid storing some values in ZQ0SR0. Thus Linux will read the ZQ0SR0
register and cache its value in RAM after processing it (using
modified_gray_code array). The bootloader will restore the processed value.
Fixes: d2d4716d83 ("ARM: at91: pm: save ddr phy calibration data to securam")
Suggested-by: Frederic Schumacher <frederic.schumacher@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220826083927.3107272-4-claudiu.beznea@microchip.com
It has been discovered that on some parts, from time to time, self-refresh
procedure doesn't work as expected. Debugging and investigating it proved
that disabling AC DLL introduce glitches in RAM controllers which
leads to unexpected behavior. This is confirmed as a hardware bug. DLL
bypass disables 3 DLLs: 2 DX DLLs and AC DLL. Thus, keep only DX DLLs
disabled. This introduce 6mA extra current consumption on VDDCORE when
switching to any ULP mode or standby mode but the self-refresh procedure
still works.
Fixes: f0bbf17958 ("ARM: at91: pm: add self-refresh support for sama7g5")
Suggested-by: Frederic Schumacher <frederic.schumacher@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Tested-by: Cristian Birsan <cristian.birsan@microchip.com>
Link: https://lore.kernel.org/r/20220826083927.3107272-3-claudiu.beznea@microchip.com
For concerns about security, the register to enable/disable IOMMU of
SMI LARB should only be configured in secure world. Thus, we add some
SMC command for multimedia master to enable/disable MM IOMMU in ATF by
setting the register of SMI LARB. This function is prepared for MT8188.
Signed-off-by: Chengci.Xu <chengci.xu@mediatek.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220817124608.10062-4-chengci.xu@mediatek.com
This is a partial revert of commit c295f9831f ("net: mscc: ocelot:
switch from {,un}set to {,un}assign for tag_8021q CPU ports"), because
as it turns out, this isn't how tag_8021q CPU ports under a LAG are
supposed to work.
Under that scenario, all user ports are "assigned" to the single
tag_8021q CPU port represented by the logical port corresponding to the
bonding interface. So one CPU port in a LAG would have is_dsa_8021q_cpu
set to true (the one whose physical port ID is equal to the logical port
ID), and the other one to false.
In turn, this makes 2 undesirable things happen:
(1) PGID_CPU contains only the first physical CPU port, rather than both
(2) only the first CPU port will be added to the private VLANs used by
ocelot for VLAN-unaware bridging
To make the driver behave in the same way for both bonded CPU ports, we
need to bring back the old concept of setting up a port as a tag_8021q
CPU port, and this is what deals with VLAN membership and PGID_CPU
updating. But we also need the CPU port "assignment" (the user to CPU
port affinity), and this is what updates the PGID_SRC forwarding rules.
All DSA CPU ports are statically configured for tag_8021q mode when the
tagging protocol is changed to ocelot-8021q. User ports are "assigned"
to one CPU port or the other dynamically (this will be handled by a
future change).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
With so many counter addresses recently discovered as being wrong, it is
desirable to at least have a central database of information, rather
than two: one through the SYS_COUNT_* registers (used for
ndo_get_stats64), and the other through the offset field of struct
ocelot_stat_layout elements (used for ethtool -S).
The strategy will be to keep the SYS_COUNT_* definitions as the single
source of truth, but for that we need to expand our current definitions
to cover all registers. Then we need to convert the ocelot region
creation logic, and stats worker, to the read semantics imposed by going
through SYS_COUNT_* absolute register addresses, rather than offsets
of 32-bit words relative to SYS_COUNT_RX_OCTETS (which should have been
SYS_CNT, by the way).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ocelot counters are 32-bit and require periodic reading, every 2
seconds, by ocelot_port_update_stats(), so that wraparounds are
detected.
Currently, the counters reported by ocelot_get_stats64() come from the
32-bit hardware counters directly, rather than from the 64-bit
accumulated ocelot->stats, and this is a problem for their integrity.
The strategy is to make ocelot_get_stats64() able to cherry-pick
individual stats from ocelot->stats the way in which it currently reads
them out from SYS_COUNT_* registers. But currently it can't, because
ocelot->stats is an opaque u64 array that's used only to feed data into
ethtool -S.
To solve that problem, we need to make ocelot->stats indexable, and
associate each element with an element of struct ocelot_stat_layout used
by ethtool -S.
This makes ocelot_stat_layout a fat (and possibly sparse) array, so we
need to change the way in which we access it. We no longer need
OCELOT_STAT_END as a sentinel, because we know the array's size
(OCELOT_NUM_STATS). We just need to skip the array elements that were
left unpopulated for the switch revision (ocelot, felix, seville).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ocelot_get_stats64() currently runs unlocked and therefore may collide
with ocelot_port_update_stats() which indirectly accesses the same
counters. However, ocelot_get_stats64() runs in atomic context, and we
cannot simply take the sleepable ocelot->stats_lock mutex. We need to
convert it to an atomic spinlock first. Do that as a preparatory change.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reading stats using the SYS_COUNT_* register definitions is only used by
ocelot_get_stats64() from the ocelot switchdev driver, however,
currently the bucket definitions are incorrect.
Separately, on both RX and TX, we have the following problems:
- a 256-1023 bucket which actually tracks the 256-511 packets
- the 1024-1526 bucket actually tracks the 512-1023 packets
- the 1527-max bucket actually tracks the 1024-1526 packets
=> nobody tracks the packets from the real 1527-max bucket
Additionally, the RX_PAUSE, RX_CONTROL, RX_LONGS and RX_CLASSIFIED_DROPS
all track the wrong thing. However this doesn't seem to have any
consequence, since ocelot_get_stats64() doesn't use these.
Even though this problem only manifests itself for the switchdev driver,
we cannot split the fix for ocelot and for DSA, since it requires fixing
the bucket definitions from enum ocelot_reg, which makes us necessarily
adapt the structures from felix and seville as well.
Fixes: 84705fc165 ("net: dsa: felix: introduce support for Seville VSC9953 switch")
Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Fixes: a556c76adc ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Here is the large set of char and misc and other driver subsystem
changes for 6.0-rc1.
Highlights include:
- large set of IIO driver updates, additions, and cleanups
- new habanalabs device support added (loads of register maps
much like GPUs have)
- soundwire driver updates
- phy driver updates
- slimbus driver updates
- tiny virt driver fixes and updates
- misc driver fixes and updates
- interconnect driver updates
- hwtracing driver updates
- fpga driver updates
- extcon driver updates
- firmware driver updates
- counter driver update
- mhi driver fixes and updates
- binder driver fixes and updates
- speakup driver fixes
Full details are in the long shortlog contents.
All of these have been in linux-next for a while without any reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYup9QQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylBKQCfaSuzl9ZP9dTvAw2FPp14oRqXnpoAnicvWAoq
1vU9Vtq2c73uBVLdZm4m
=AwP3
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver updates from Greg KH:
"Here is the large set of char and misc and other driver subsystem
changes for 6.0-rc1.
Highlights include:
- large set of IIO driver updates, additions, and cleanups
- new habanalabs device support added (loads of register maps much
like GPUs have)
- soundwire driver updates
- phy driver updates
- slimbus driver updates
- tiny virt driver fixes and updates
- misc driver fixes and updates
- interconnect driver updates
- hwtracing driver updates
- fpga driver updates
- extcon driver updates
- firmware driver updates
- counter driver update
- mhi driver fixes and updates
- binder driver fixes and updates
- speakup driver fixes
All of these have been in linux-next for a while without any reported
problems"
* tag 'char-misc-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (634 commits)
drivers: lkdtm: fix clang -Wformat warning
char: remove VR41XX related char driver
misc: Mark MICROCODE_MINOR unused
spmi: trace: fix stack-out-of-bound access in SPMI tracing functions
dt-bindings: iio: adc: Add compatible for MT8188
iio: light: isl29028: Fix the warning in isl29028_remove()
iio: accel: sca3300: Extend the trigger buffer from 16 to 32 bytes
iio: fix iio_format_avail_range() printing for none IIO_VAL_INT
iio: adc: max1027: unlock on error path in max1027_read_single_value()
iio: proximity: sx9324: add empty line in front of bullet list
iio: magnetometer: hmc5843: Remove duplicate 'the'
iio: magn: yas530: Use DEFINE_RUNTIME_DEV_PM_OPS() and pm_ptr() macros
iio: magnetometer: ak8974: Use DEFINE_RUNTIME_DEV_PM_OPS() and pm_ptr() macros
iio: light: veml6030: Use DEFINE_RUNTIME_DEV_PM_OPS() and pm_ptr() macros
iio: light: vcnl4035: Use DEFINE_RUNTIME_DEV_PM_OPS() and pm_ptr() macros
iio: light: vcnl4000: Use DEFINE_RUNTIME_DEV_PM_OPS() and pm_ptr() macros
iio: light: tsl2591: Use DEFINE_RUNTIME_DEV_PM_OPS() and pm_ptr()
iio: light: tsl2583: Use DEFINE_RUNTIME_DEV_PM_OPS and pm_ptr()
iio: light: isl29028: Use DEFINE_RUNTIME_DEV_PM_OPS() and pm_ptr()
iio: light: gp2ap002: Switch to DEFINE_RUNTIME_DEV_PM_OPS and pm_ptr()
...
In a future change we will need to remember the entire tc-taprio config
on all ports rather than just the base time, so use the
taprio_offload_get() helper function to replace ocelot_port->base_time
with ocelot_port->taprio.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When adjusting the PTP clock, the base time of the TAS configuration
will become unreliable. We need reset the TAS configuration by using a
new base time.
For example, if the driver gets a base time 0 of Qbv configuration from
user, and current time is 20000. The driver will set the TAS base time
to be 20000. After the PTP clock adjustment, the current time becomes
10000. If the TAS base time is still 20000, it will be a future time,
and TAS entry list will stop running. Another example, if the current
time becomes to be 10000000 after PTP clock adjust, a large time offset
can cause the hardware to hang.
This patch introduces a tas_clock_adjust() function to reset the TAS
module by using a new base time after the PTP clock adjustment. This can
avoid issues above.
Due to PTP clock adjustment can occur at any time, it may conflict with
the TAS configuration. We introduce a new TAS lock to serialize the
access to the TAS registers.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PMI8998 and PM660 expose the fab_id, this is needed by drivers like
the RRADC to calibrate ADC values.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220429220904.137297-4-caleb.connolly@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some PMIC functions such as the RRADC need to be aware of the PMIC
chip revision information to implement errata or otherwise adjust
behaviour, export the PMIC information to enable this.
This is specifically required to enable the RRADC to adjust
coefficients based on which chip fab the PMIC was produced in,
this can vary per unique device and therefore has to be read at
runtime.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220429220904.137297-3-caleb.connolly@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There are minor updates to SoC specific drivers for chips by Rockchip,
Samsung, NVIDIA, TI, NXP, i.MX, Qualcomm, and Broadcom. Noteworthy
driver changes include:
- Several conversions of DT bindings to yaml format.
- Renesas adds driver support for R-Car V4H, RZ/V2M and RZ/G2UL SoCs.
- Qualcomm adds a bus driver for the SSC (Snapdragon Sensor Core),
and support for more chips in the RPMh power domains and the soc-id.
- NXP has a new driver for the HDMI blk-ctrl on i.MX8MP.
- Apple M1 gains support for the on-chip NVMe controller, making it
possible to finally use the internal disks. This also includes SoC
drivers for their RTKit IPC and for the SART DMA address filter.
For other subsystems that merge their drivers through the SoC tree,
we have
- Firmware drivers for the ARM firmware stack including TEE, OP-TEE,
SCMI and FF-A get a number of smaller updates and cleanups. OP-TEE
now has a cache for firmware argument structures as an optimization,
and SCMI now supports the 3.1 version of the specification.
- Reset controller updates to Amlogic, ASpeed, Renesas and ACPI drivers
- Memory controller updates for Tegra, and a few updates for other
platforms.
-----BEGIN PGP SIGNATURE-----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=XoLF
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM driver updates from Arnd Bergmann:
"There are minor updates to SoC specific drivers for chips by Rockchip,
Samsung, NVIDIA, TI, NXP, i.MX, Qualcomm, and Broadcom.
Noteworthy driver changes include:
- Several conversions of DT bindings to yaml format.
- Renesas adds driver support for R-Car V4H, RZ/V2M and RZ/G2UL SoCs.
- Qualcomm adds a bus driver for the SSC (Snapdragon Sensor Core),
and support for more chips in the RPMh power domains and the
soc-id.
- NXP has a new driver for the HDMI blk-ctrl on i.MX8MP.
- Apple M1 gains support for the on-chip NVMe controller, making it
possible to finally use the internal disks. This also includes SoC
drivers for their RTKit IPC and for the SART DMA address filter.
For other subsystems that merge their drivers through the SoC tree, we
have
- Firmware drivers for the ARM firmware stack including TEE, OP-TEE,
SCMI and FF-A get a number of smaller updates and cleanups. OP-TEE
now has a cache for firmware argument structures as an
optimization, and SCMI now supports the 3.1 version of the
specification.
- Reset controller updates to Amlogic, ASpeed, Renesas and ACPI
drivers
- Memory controller updates for Tegra, and a few updates for other
platforms"
* tag 'arm-drivers-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (159 commits)
memory: tegra: Add MC error logging on Tegra186 onward
memory: tegra: Add memory controller channels support
memory: tegra: Add APE memory clients for Tegra234
memory: tegra: Add Tegra234 support
nvme-apple: fix sparse endianess warnings
soc/tegra: pmc: Document core domain fields
soc: qcom: pdr: use static for servreg_* variables
soc: imx: fix semicolon.cocci warnings
soc: renesas: R-Car V3U is R-Car Gen4
soc: imx: add i.MX8MP HDMI blk-ctrl
soc: imx: imx8m-blk-ctrl: Add i.MX8MP media blk-ctrl
soc: imx: add i.MX8MP HSIO blk-ctrl
soc: imx: imx8m-blk-ctrl: set power device name
soc: qcom: llcc: Add sc8180x and sc8280xp configurations
dt-bindings: arm: msm: Add sc8180x and sc8280xp LLCC compatibles
soc/tegra: pmc: Select REGMAP
dt-bindings: reset: st,sti-powerdown: Convert to yaml
dt-bindings: reset: st,sti-picophyreset: Convert to yaml
dt-bindings: reset: socfpga: Convert to yaml
dt-bindings: reset: snps,axs10x-reset: Convert to yaml
...
Core
----
- Support TCPv6 segmentation offload with super-segments larger than
64k bytes using the IPv6 Jumbogram extension header (AKA BIG TCP).
- Generalize skb freeing deferral to per-cpu lists, instead of
per-socket lists.
- Add a netdev statistic for packets dropped due to L2 address
mismatch (rx_otherhost_dropped).
- Continue work annotating skb drop reasons.
- Accept alternative netdev names (ALT_IFNAME) in more netlink
requests.
- Add VLAN support for AF_PACKET SOCK_RAW GSO.
- Allow receiving skb mark from the socket as a cmsg.
- Enable memcg accounting for veth queues, sysctl tables and IPv6.
BPF
---
- Add libbpf support for User Statically-Defined Tracing (USDTs).
- Speed up symbol resolution for kprobes multi-link attachments.
- Support storing typed pointers to referenced and unreferenced
objects in BPF maps.
- Add support for BPF link iterator.
- Introduce access to remote CPU map elements in BPF per-cpu map.
- Allow middle-of-the-road settings for the
kernel.unprivileged_bpf_disabled sysctl.
- Implement basic types of dynamic pointers e.g. to allow for
dynamically sized ringbuf reservations without extra memory copies.
Protocols
---------
- Retire port only listening_hash table, add a second bind table
hashed by port and address. Avoid linear list walk when binding
to very popular ports (e.g. 443).
- Add bridge FDB bulk flush filtering support allowing user space
to remove all FDB entries matching a condition.
- Introduce accept_unsolicited_na sysctl for IPv6 to implement
router-side changes for RFC9131.
- Support for MPTCP path manager in user space.
- Add MPTCP support for fallback to regular TCP for connections
that have never connected additional subflows or transmitted
out-of-sequence data (partial support for RFC8684 fallback).
- Avoid races in MPTCP-level window tracking, stabilize and improve
throughput.
- Support lockless operation of GRE tunnels with seq numbers enabled.
- WiFi support for host based BSS color collision detection.
- Add support for SO_TXTIME/SCM_TXTIME on CAN sockets.
- Support transmission w/o flow control in CAN ISOTP (ISO 15765-2).
- Support zero-copy Tx with TLS 1.2 crypto offload (sendfile).
- Allow matching on the number of VLAN tags via tc-flower.
- Add tracepoint for tcp_set_ca_state().
Driver API
----------
- Improve error reporting from classifier and action offload.
- Add support for listing line cards in switches (devlink).
- Add helpers for reporting page pool statistics with ethtool -S.
- Add support for reading clock cycles when using PTP virtual clocks,
instead of having the driver convert to time before reporting.
This makes it possible to report time from different vclocks.
- Support configuring low-latency Tx descriptor push via ethtool.
- Separate Clause 22 and Clause 45 MDIO accesses more explicitly.
New hardware / drivers
----------------------
- Ethernet:
- Marvell's Octeon NIC PCI Endpoint support (octeon_ep)
- Sunplus SP7021 SoC (sp7021_emac)
- Add support for Renesas RZ/V2M (in ravb)
- Add support for MediaTek mt7986 switches (in mtk_eth_soc)
- Ethernet PHYs:
- ADIN1100 industrial PHYs (w/ 10BASE-T1L and SQI reporting)
- TI DP83TD510 PHY
- Microchip LAN8742/LAN88xx PHYs
- WiFi:
- Driver for pureLiFi X, XL, XC devices (plfxlc)
- Driver for Silicon Labs devices (wfx)
- Support for WCN6750 (in ath11k)
- Support Realtek 8852ce devices (in rtw89)
- Mobile:
- MediaTek T700 modems (Intel 5G 5000 M.2 cards)
- CAN:
- ctucanfd: add support for CTU CAN FD open-source IP core
from Czech Technical University in Prague
Drivers
-------
- Delete a number of old drivers still using virt_to_bus().
- Ethernet NICs:
- intel: support TSO on tunnels MPLS
- broadcom: support multi-buffer XDP
- nfp: support VF rate limiting
- sfc: use hardware tx timestamps for more than PTP
- mlx5: multi-port eswitch support
- hyper-v: add support for XDP_REDIRECT
- atlantic: XDP support (including multi-buffer)
- macb: improve real-time perf by deferring Tx processing to NAPI
- High-speed Ethernet switches:
- mlxsw: implement basic line card information querying
- prestera: add support for traffic policing on ingress and egress
- Embedded Ethernet switches:
- lan966x: add support for packet DMA (FDMA)
- lan966x: add support for PTP programmable pins
- ti: cpsw_new: enable bc/mc storm prevention
- Qualcomm 802.11ax WiFi (ath11k):
- Wake-on-WLAN support for QCA6390 and WCN6855
- device recovery (firmware restart) support
- support setting Specific Absorption Rate (SAR) for WCN6855
- read country code from SMBIOS for WCN6855/QCA6390
- enable keep-alive during WoWLAN suspend
- implement remain-on-channel support
- MediaTek WiFi (mt76):
- support Wireless Ethernet Dispatch offloading packet movement
between the Ethernet switch and WiFi interfaces
- non-standard VHT MCS10-11 support
- mt7921 AP mode support
- mt7921 IPv6 NS offload support
- Ethernet PHYs:
- micrel: ksz9031/ksz9131: cabletest support
- lan87xx: SQI support for T1 PHYs
- lan937x: add interrupt support for link detection
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Wjii
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core
----
- Support TCPv6 segmentation offload with super-segments larger than
64k bytes using the IPv6 Jumbogram extension header (AKA BIG TCP).
- Generalize skb freeing deferral to per-cpu lists, instead of
per-socket lists.
- Add a netdev statistic for packets dropped due to L2 address
mismatch (rx_otherhost_dropped).
- Continue work annotating skb drop reasons.
- Accept alternative netdev names (ALT_IFNAME) in more netlink
requests.
- Add VLAN support for AF_PACKET SOCK_RAW GSO.
- Allow receiving skb mark from the socket as a cmsg.
- Enable memcg accounting for veth queues, sysctl tables and IPv6.
BPF
---
- Add libbpf support for User Statically-Defined Tracing (USDTs).
- Speed up symbol resolution for kprobes multi-link attachments.
- Support storing typed pointers to referenced and unreferenced
objects in BPF maps.
- Add support for BPF link iterator.
- Introduce access to remote CPU map elements in BPF per-cpu map.
- Allow middle-of-the-road settings for the
kernel.unprivileged_bpf_disabled sysctl.
- Implement basic types of dynamic pointers e.g. to allow for
dynamically sized ringbuf reservations without extra memory copies.
Protocols
---------
- Retire port only listening_hash table, add a second bind table
hashed by port and address. Avoid linear list walk when binding to
very popular ports (e.g. 443).
- Add bridge FDB bulk flush filtering support allowing user space to
remove all FDB entries matching a condition.
- Introduce accept_unsolicited_na sysctl for IPv6 to implement
router-side changes for RFC9131.
- Support for MPTCP path manager in user space.
- Add MPTCP support for fallback to regular TCP for connections that
have never connected additional subflows or transmitted
out-of-sequence data (partial support for RFC8684 fallback).
- Avoid races in MPTCP-level window tracking, stabilize and improve
throughput.
- Support lockless operation of GRE tunnels with seq numbers enabled.
- WiFi support for host based BSS color collision detection.
- Add support for SO_TXTIME/SCM_TXTIME on CAN sockets.
- Support transmission w/o flow control in CAN ISOTP (ISO 15765-2).
- Support zero-copy Tx with TLS 1.2 crypto offload (sendfile).
- Allow matching on the number of VLAN tags via tc-flower.
- Add tracepoint for tcp_set_ca_state().
Driver API
----------
- Improve error reporting from classifier and action offload.
- Add support for listing line cards in switches (devlink).
- Add helpers for reporting page pool statistics with ethtool -S.
- Add support for reading clock cycles when using PTP virtual clocks,
instead of having the driver convert to time before reporting. This
makes it possible to report time from different vclocks.
- Support configuring low-latency Tx descriptor push via ethtool.
- Separate Clause 22 and Clause 45 MDIO accesses more explicitly.
New hardware / drivers
----------------------
- Ethernet:
- Marvell's Octeon NIC PCI Endpoint support (octeon_ep)
- Sunplus SP7021 SoC (sp7021_emac)
- Add support for Renesas RZ/V2M (in ravb)
- Add support for MediaTek mt7986 switches (in mtk_eth_soc)
- Ethernet PHYs:
- ADIN1100 industrial PHYs (w/ 10BASE-T1L and SQI reporting)
- TI DP83TD510 PHY
- Microchip LAN8742/LAN88xx PHYs
- WiFi:
- Driver for pureLiFi X, XL, XC devices (plfxlc)
- Driver for Silicon Labs devices (wfx)
- Support for WCN6750 (in ath11k)
- Support Realtek 8852ce devices (in rtw89)
- Mobile:
- MediaTek T700 modems (Intel 5G 5000 M.2 cards)
- CAN:
- ctucanfd: add support for CTU CAN FD open-source IP core from
Czech Technical University in Prague
Drivers
-------
- Delete a number of old drivers still using virt_to_bus().
- Ethernet NICs:
- intel: support TSO on tunnels MPLS
- broadcom: support multi-buffer XDP
- nfp: support VF rate limiting
- sfc: use hardware tx timestamps for more than PTP
- mlx5: multi-port eswitch support
- hyper-v: add support for XDP_REDIRECT
- atlantic: XDP support (including multi-buffer)
- macb: improve real-time perf by deferring Tx processing to NAPI
- High-speed Ethernet switches:
- mlxsw: implement basic line card information querying
- prestera: add support for traffic policing on ingress and egress
- Embedded Ethernet switches:
- lan966x: add support for packet DMA (FDMA)
- lan966x: add support for PTP programmable pins
- ti: cpsw_new: enable bc/mc storm prevention
- Qualcomm 802.11ax WiFi (ath11k):
- Wake-on-WLAN support for QCA6390 and WCN6855
- device recovery (firmware restart) support
- support setting Specific Absorption Rate (SAR) for WCN6855
- read country code from SMBIOS for WCN6855/QCA6390
- enable keep-alive during WoWLAN suspend
- implement remain-on-channel support
- MediaTek WiFi (mt76):
- support Wireless Ethernet Dispatch offloading packet movement
between the Ethernet switch and WiFi interfaces
- non-standard VHT MCS10-11 support
- mt7921 AP mode support
- mt7921 IPv6 NS offload support
- Ethernet PHYs:
- micrel: ksz9031/ksz9131: cabletest support
- lan87xx: SQI support for T1 PHYs
- lan937x: add interrupt support for link detection"
* tag 'net-next-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1809 commits)
ptp: ocp: Add firmware header checks
ptp: ocp: fix PPS source selector debugfs reporting
ptp: ocp: add .init function for sma_op vector
ptp: ocp: vectorize the sma accessor functions
ptp: ocp: constify selectors
ptp: ocp: parameterize input/output sma selectors
ptp: ocp: revise firmware display
ptp: ocp: add Celestica timecard PCI ids
ptp: ocp: Remove #ifdefs around PCI IDs
ptp: ocp: 32-bit fixups for pci start address
Revert "net/smc: fix listen processing for SMC-Rv2"
ath6kl: Use cc-disable-warning to disable -Wdangling-pointer
selftests/bpf: Dynptr tests
bpf: Add dynptr data slices
bpf: Add bpf_dynptr_read and bpf_dynptr_write
bpf: Dynptr support for ring buffers
bpf: Add bpf_dynptr_from_mem for local dynptrs
bpf: Add verifier support for dynptrs
bpf: Suppress 'passing zero to PTR_ERR' warning
bpf: Introduce bpf_arch_text_invalidate for bpf_prog_pack
...
- Update the Energy Model support code to allow the Energy Model to be
artificial, which means that the power values may not be on a uniform
scale with other devices providing power information, and update the
cpufreq_cooling and devfreq_cooling thermal drivers to support
artificial Energy Models (Lukasz Luba).
- Make DTPM check the Energy Model type (Lukasz Luba).
- Fix policy counter decrementation in cpufreq if Energy Model is in
use (Pierre Gondois).
- Add CPU-based scaling support to passive devfreq governor (Saravana
Kannan, Chanwoo Choi).
- Update the rk3399_dmc devfreq driver (Brian Norris).
- Export dev_pm_ops instead of suspend() and resume() in the IIO
chemical scd30 driver (Jonathan Cameron).
- Add namespace variants of EXPORT[_GPL]_SIMPLE_DEV_PM_OPS and
PM-runtime counterparts (Jonathan Cameron).
- Move symbol exports in the IIO chemical scd30 driver into the
IIO_SCD30 namespace (Jonathan Cameron).
- Avoid device PM-runtime usage count underflows (Rafael Wysocki).
- Allow dynamic debug to control printing of PM messages (David
Cohen).
- Fix some kernel-doc comments in hibernation code (Yang Li, Haowen
Bai).
- Preserve ACPI-table override during hibernation (Amadeusz Sławiński).
- Improve support for suspend-to-RAM for PSCI OSI mode (Ulf Hansson).
- Make Intel RAPL power capping driver support the RaptorLake and
AlderLake N processors (Zhang Rui, Sumeet Pawnikar).
- Remove redundant store to value after multiply in the RAPL power
capping driver (Colin Ian King).
- Add AlderLake processor support to the intel_idle driver (Zhang Rui).
- Fix regression leading to no genpd governor in the PSCI cpuidle
driver and fix the riscv-sbi cpuidle driver to allow a genpd
governor to be used (Ulf Hansson).
- Fix cpufreq governor clean up code to avoid using kfree() directly
to free kobject-based items (Kevin Hao).
- Prepare cpufreq for powerpc's asm/prom.h cleanup (Christophe Leroy).
- Make intel_pstate notify frequency invariance code when no_turbo is
turned on and off (Chen Yu).
- Add Sapphire Rapids OOB mode support to intel_pstate (Srinivas
Pandruvada).
- Make cpufreq avoid unnecessary frequency updates due to mismatch
between hardware and the frequency table (Viresh Kumar).
- Make remove_cpu_dev_symlink() clear the real_cpus mask to simplify
code (Viresh Kumar).
- Rearrange cpufreq_offline() and cpufreq_remove_dev() to make the
calling convention for some driver callbacks consistent (Rafael
Wysocki).
- Avoid accessing half-initialized cpufreq policies from the show()
and store() sysfs functions (Schspa Shi).
- Rearrange cpufreq_offline() to make the calling convention for some
driver callbacks consistent (Schspa Shi).
- Update CPPC handling in cpufreq (Pierre Gondois).
- Extend dev_pm_domain_detach() doc (Krzysztof Kozlowski).
- Move genpd's time-accounting to ktime_get_mono_fast_ns() (Ulf
Hansson).
- Improve the way genpd deals with its governors (Ulf Hansson).
- Update the turbostat utility to version 2022.04.16 (Len Brown,
Dan Merillat, Sumeet Pawnikar, Zephaniah E. Loss-Cutler-Hull, Chen
Yu).
-----BEGIN PGP SIGNATURE-----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=Hewm
-----END PGP SIGNATURE-----
Merge tag 'pm-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These add support for 'artificial' Energy Models in which power
numbers for different entities may be in different scales, add support
for some new hardware, fix bugs and clean up code in multiple places.
Specifics:
- Update the Energy Model support code to allow the Energy Model to
be artificial, which means that the power values may not be on a
uniform scale with other devices providing power information, and
update the cpufreq_cooling and devfreq_cooling thermal drivers to
support artificial Energy Models (Lukasz Luba).
- Make DTPM check the Energy Model type (Lukasz Luba).
- Fix policy counter decrementation in cpufreq if Energy Model is in
use (Pierre Gondois).
- Add CPU-based scaling support to passive devfreq governor (Saravana
Kannan, Chanwoo Choi).
- Update the rk3399_dmc devfreq driver (Brian Norris).
- Export dev_pm_ops instead of suspend() and resume() in the IIO
chemical scd30 driver (Jonathan Cameron).
- Add namespace variants of EXPORT[_GPL]_SIMPLE_DEV_PM_OPS and
PM-runtime counterparts (Jonathan Cameron).
- Move symbol exports in the IIO chemical scd30 driver into the
IIO_SCD30 namespace (Jonathan Cameron).
- Avoid device PM-runtime usage count underflows (Rafael Wysocki).
- Allow dynamic debug to control printing of PM messages (David
Cohen).
- Fix some kernel-doc comments in hibernation code (Yang Li, Haowen
Bai).
- Preserve ACPI-table override during hibernation (Amadeusz
Sławiński).
- Improve support for suspend-to-RAM for PSCI OSI mode (Ulf Hansson).
- Make Intel RAPL power capping driver support the RaptorLake and
AlderLake N processors (Zhang Rui, Sumeet Pawnikar).
- Remove redundant store to value after multiply in the RAPL power
capping driver (Colin Ian King).
- Add AlderLake processor support to the intel_idle driver (Zhang
Rui).
- Fix regression leading to no genpd governor in the PSCI cpuidle
driver and fix the riscv-sbi cpuidle driver to allow a genpd
governor to be used (Ulf Hansson).
- Fix cpufreq governor clean up code to avoid using kfree() directly
to free kobject-based items (Kevin Hao).
- Prepare cpufreq for powerpc's asm/prom.h cleanup (Christophe
Leroy).
- Make intel_pstate notify frequency invariance code when no_turbo is
turned on and off (Chen Yu).
- Add Sapphire Rapids OOB mode support to intel_pstate (Srinivas
Pandruvada).
- Make cpufreq avoid unnecessary frequency updates due to mismatch
between hardware and the frequency table (Viresh Kumar).
- Make remove_cpu_dev_symlink() clear the real_cpus mask to simplify
code (Viresh Kumar).
- Rearrange cpufreq_offline() and cpufreq_remove_dev() to make the
calling convention for some driver callbacks consistent (Rafael
Wysocki).
- Avoid accessing half-initialized cpufreq policies from the show()
and store() sysfs functions (Schspa Shi).
- Rearrange cpufreq_offline() to make the calling convention for some
driver callbacks consistent (Schspa Shi).
- Update CPPC handling in cpufreq (Pierre Gondois).
- Extend dev_pm_domain_detach() doc (Krzysztof Kozlowski).
- Move genpd's time-accounting to ktime_get_mono_fast_ns() (Ulf
Hansson).
- Improve the way genpd deals with its governors (Ulf Hansson).
- Update the turbostat utility to version 2022.04.16 (Len Brown, Dan
Merillat, Sumeet Pawnikar, Zephaniah E. Loss-Cutler-Hull, Chen Yu)"
* tag 'pm-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (94 commits)
PM: domains: Trust domain-idle-states from DT to be correct by genpd
PM: domains: Measure power-on/off latencies in genpd based on a governor
PM: domains: Allocate governor data dynamically based on a genpd governor
PM: domains: Clean up some code in pm_genpd_init() and genpd_remove()
PM: domains: Fix initialization of genpd's next_wakeup
PM: domains: Fixup QoS latency measurements for IRQ safe devices in genpd
PM: domains: Measure suspend/resume latencies in genpd based on governor
PM: domains: Move the next_wakeup variable into the struct gpd_timing_data
PM: domains: Allocate gpd_timing_data dynamically based on governor
PM: domains: Skip another warning in irq_safe_dev_in_sleep_domain()
PM: domains: Rename irq_safe_dev_in_no_sleep_domain() in genpd
PM: domains: Don't check PM_QOS_FLAG_NO_POWER_OFF in genpd
PM: domains: Drop redundant code for genpd always-on governor
PM: domains: Add GENPD_FLAG_RPM_ALWAYS_ON for the always-on governor
powercap: intel_rapl: remove redundant store to value after multiply
cpufreq: CPPC: Enable dvfs_possible_from_any_cpu
cpufreq: CPPC: Enable fast_switch
ACPI: CPPC: Assume no transition latency if no PCCT
ACPI: bus: Set CPPC _OSC bits for all and when CPPC_LIB is supported
ACPI: CPPC: Check _OSC for flexible address space
...
The NXP Cryptographic Acceleration and Assurance Module (CAAM)
can be used to protect user-defined data across system reboot:
- When the system is fused and boots into secure state, the master
key is a unique never-disclosed device-specific key
- random key is encrypted by key derived from master key
- data is encrypted using the random key
- encrypted data and its encrypted random key are stored alongside
- This blob can now be safely stored in non-volatile memory
On next power-on:
- blob is loaded into CAAM
- CAAM writes decrypted data either into memory or key register
Add functions to realize encrypting and decrypting into memory alongside
the CAAM driver.
They will be used in a later commit as a source for the trusted key
seal/unseal mechanism.
Reviewed-by: David Gstir <david@sigma-star.at>
Reviewed-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Tested-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Tested-by: Michael Walle <michael@walle.cc> # on ls1028a (non-E and E)
Tested-by: John Ernberg <john.ernberg@actia.se> # iMX8QXP
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Update the VCAP filters to support multiple tag_8021q CPU ports.
TX works using a filter for VLAN ID on the ingress of the CPU port, with
a redirect and a VLAN pop action. This can be updated trivially by
amending the ingress port mask of this rule to match on all tag_8021q
CPU ports.
RX works using a filter for ingress port on the egress of the CPU port,
with a VLAN push action. Here we need to replicate these filters for
each tag_8021q CPU port, and let them all have the same action.
This means that the OCELOT_VCAP_ES0_TAG_8021Q_RXVLAN() cookie needs to
encode a unique value for every {user port, CPU port} pair it's given.
Do this by encoding the CPU port in the upper 16 bits of the cookie, and
the user port in the lower 16 bits.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a desire for the felix driver to gain support for multiple
tag_8021q CPU ports, but the current model prevents it.
This is because ocelot_apply_bridge_fwd_mask() only takes into
consideration whether a port is a tag_8021q CPU port, but not whose CPU
port it is.
We need a model where we can have a direct affinity between an ocelot
port and a tag_8021q CPU port. This serves as the basis for multiple CPU
ports.
Declare a "dsa_8021q_cpu" backpointer in struct ocelot_port which
encodes that affinity. Repurpose the "ocelot_set_dsa_8021q_cpu" API to
"ocelot_assign_dsa_8021q_cpu" to express the change of paradigm.
Note that this change makes the first practical use of the new
ocelot_port->index field in ocelot_port_unassign_dsa_8021q_cpu(), where
we need to remove the old tag_8021q CPU port from the reserved VLAN range.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add more logic to ocelot_port_{,un}set_dsa_8021q_cpu() from the ocelot
switch lib by encapsulating the ocelot_apply_bridge_fwd_mask() call that
felix used to have.
This is necessary because the CPU port change procedure will also need
to do this, and it's good to reduce code duplication by having an entry
point in the ocelot switch lib that does all that is needed.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Detailed description for this pull request:
1. Update devfreq core
- Add cpu based scaling support to passive governor. Some device like
cache might require the dynamic frequency scaling. But, it has very
tightly to cpu frequency. So that use passive governor to scale
the frequency according to current cpu frequency.
To decide the frequency of the device, the governor does one of the following:
: Derives the optimal devfreq device opp from required-opps property of
the parent cpu opp_table.
: Scales the device frequency in proportion to the CPU frequency. So, if
the CPUs are running at their max frequency, the device runs at its
max frequency. If the CPUs are running at their min frequency, the
device runs at its min frequency. It is interpolated for frequencies
in between.
2. Update devfreq driver
- Update rk3399_dmc.c as following:
: Convert dt-binding document to YAML and deprecate unused properties.
: Use Hz units for the device-tree properties of rk3399_dmc.
: rk3399_dmc is able to set the idle time before changing the dmc clock.
Specify idle time parameters by using nano-second unit on dt bidning.
: Add new disable-freq properties to optimize the power-saving feature
of rk3399_dmc.
: Disable devfreq-event device on remove() to fix unbalanced
enable-disable count.
: Use devm_pm_opp_of_add_table()
: Block PMU (Power-Management Unit) transitions when scaling frequency
by ARM Trust Firmware in order to fix the conflict between PMU and DMC
(Dynamic Memory Controller).
-----BEGIN PGP SIGNATURE-----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=/3W8
-----END PGP SIGNATURE-----
Merge tag 'devfreq-next-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/linux
Pull devfreq changes for 5.19-rc1 from Chanwoo Choi:
"1. Update devfreq core
- Add cpu based scaling support to passive governor. Some device like
cache might require the dynamic frequency scaling. But, it has very
tightly to cpu frequency. So that use passive governor to scale
the frequency according to current cpu frequency.
To decide the frequency of the device, the governor does one of the following:
: Derives the optimal devfreq device opp from required-opps property of
the parent cpu opp_table.
: Scales the device frequency in proportion to the CPU frequency. So, if
the CPUs are running at their max frequency, the device runs at its
max frequency. If the CPUs are running at their min frequency, the
device runs at its min frequency. It is interpolated for frequencies
in between.
2. Update devfreq drivers
- Update rk3399_dmc.c as following:
: Convert dt-binding document to YAML and deprecate unused properties.
: Use Hz units for the device-tree properties of rk3399_dmc.
: rk3399_dmc is able to set the idle time before changing the dmc clock.
Specify idle time parameters by using nano-second unit on dt bidning.
: Add new disable-freq properties to optimize the power-saving feature
of rk3399_dmc.
: Disable devfreq-event device on remove() to fix unbalanced
enable-disable count.
: Use devm_pm_opp_of_add_table()
: Block PMU (Power-Management Unit) transitions when scaling frequency
by ARM Trust Firmware in order to fix the conflict between PMU and DMC
(Dynamic Memory Controller)."
* tag 'devfreq-next-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/linux:
PM / devfreq: passive: Keep cpufreq_policy for possible cpus
PM / devfreq: passive: Reduce duplicate code when passive_devfreq case
PM / devfreq: Add cpu based scaling support to passive governor
PM / devfreq: Export devfreq_get_freq_range symbol within devfreq
PM / devfreq: rk3399_dmc: Block PMU during transitions
soc: rockchip: power-domain: Manage resource conflicts with firmware
PM / devfreq: rk3399_dmc: Avoid static (reused) profile
PM / devfreq: rk3399_dmc: Use devm_pm_opp_of_add_table()
PM / devfreq: rk3399_dmc: Disable edev on remove()
PM / devfreq: rk3399_dmc: Support new *-ns properties
PM / devfreq: rk3399_dmc: Support new disable-freq properties
PM / devfreq: rk3399_dmc: Use bitfield macro definitions for ODT_PD
PM / devfreq: rk3399_dmc: Drop excess timing properties
PM / devfreq: rk3399_dmc: Drop undocumented ondemand DT props
dt-bindings: devfreq: rk3399_dmc: Add more disable-freq properties
dt-bindings: devfreq: rk3399_dmc: Specify idle params in nanoseconds
dt-bindings: devfreq: rk3399_dmc: Fix Hz units
dt-bindings: devfreq: rk3399_dmc: Deprecate unused/redundant properties
dt-bindings: devfreq: rk3399_dmc: Convert to YAML
Currently the ocelot switch lib is unaware of the index of a struct
ocelot_port, since that is kept in the encapsulating structures of outer
drivers (struct dsa_port :: index, struct ocelot_port_private :: chip_port).
With the upcoming increase in complexity associated with assigning DSA
tag_8021q CPU ports to certain user ports, it becomes necessary for the
switch lib to be able to retrieve the index of a certain ocelot_port.
Therefore, introduce a new u8 to ocelot_port (same size as the chip_port
used by the ocelot switchdev driver) and rework the existing code to
populate and use it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is no longer used since commit 7c4bb540e9 ("net: dsa: tag_ocelot:
create separate tagger for Seville").
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for logging memory controller errors on Tegra186, Tegra194
and Tegra234. On these SoCs, interrupts can occur on multiple channels.
Add support required to read the status of interrupts across multiple
channels, log and clear them.
Also add new interrupts supported on these SoCs.
Reviewed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Ashish Mhetre <amhetre@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20220506132312.3910637-5-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
From Tegra186 onwards, the memory controller supports multiple channels.
Add support for mapping the address spaces of these channels and specify
the number of channels supported by Tegra186, Tegra194 and Tegra234.
In case of old bindings, channels won't be present. If channels are not
present then print a warning and continue so that backward compatibility
will be preserved in driver.
During error interrupts from memory controller, appropriate registers
from these channels need to be accessed for logging error info.
Signed-off-by: Ashish Mhetre <amhetre@nvidia.com>
Reviewed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20220506132312.3910637-4-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
On RK3399 platforms, power domains are managed mostly by the kernel
(drivers/soc/rockchip/pm_domains.c), but there are a few exceptions
where ARM Trusted Firmware has to be involved:
(1) system suspend/resume
(2) DRAM DVFS (a.k.a., "ddrfreq")
Exception (1) does not cause much conflict, since the kernel has
quiesced itself by the time we make the relevant PSCI call.
Exception (2) can cause conflict, because of two actions:
(a) ARM Trusted Firmware needs to read/modify/write the PMU_BUS_IDLE_REQ
register to idle the memory controller domain; the kernel driver
also has to touch this register for other domains.
(b) ARM Trusted Firmware needs to manage the clocks associated with
these domains.
To elaborate on (b): idling a power domain has always required ungating
an array of clocks; see this old explanation from Rockchip:
https://lore.kernel.org/linux-arm-kernel/54503C19.9060607@rock-chips.com/
Historically, ARM Trusted Firmware has avoided this issue by using a
special PMU_CRU_GATEDIS_CON0 register -- this register ungates all the
necessary clocks -- when idling the memory controller. Unfortunately,
we've found that this register is not 100% sufficient; it does not turn
the relevant PLLs on [0].
So it's possible to trigger issues with something like the following:
1. enable a power domain (e.g., RK3399_PD_VDU) -- kernel will
temporarily enable relevant clocks/PLLs, then turn them back off
2. a PLL (e.g., PLL_NPLL) is part of the clock tree for
RK3399_PD_VDU's clocks but otherwise unused; NPLL is disabled
3. perform a ddrfreq transition (rk3399_dmcfreq_target() -> ...
drivers/clk/rockchip/clk-ddr.c / ROCKCHIP_SIP_DRAM_FREQ)
4. ARM Trusted Firmware unagates VDU clocks (via PMU_CRU_GATEDIS_CON0)
5. ARM Trusted firmware idles the memory controller domain
6. Step 5 waits on the VDU domain/clocks, but NPLL is still off
i.e., we hang the system.
So for (b), we need to at a minimum manage the relevant PLLs on behalf
of firmware. It's easier to simply manage the whole clock tree, in a
similar way we do in rockchip_pd_power().
For (a), we need to provide mutual exclusion betwen rockchip_pd_power()
and firmware. To resolve that, we simply grab the PMU mutex and release
it when ddrfreq is done.
The Chromium OS kernel has been carrying versions of part of this hack
for a while, based on some new custom notifiers [1]. I've rewritten as a
simple function call between the drivers, which is OK because:
* the PMU driver isn't enabled, and we don't have this problem at all
(the firmware should have left us in an OK state, and there are no
runtime conflicts); or
* the PMU driver is present, and is a single instance.
And the power-domain driver cannot be removed, so there's no lifetime
management to worry about.
For completeness, there's a 'dmc_pmu_mutex' to guard (likely
theoretical?) probe()-time races. It's OK for the memory controller
driver to start running before the PMU, because the PMU will avoid any
critical actions during the block() sequence.
[0] The RK3399 TRM for PMU_CRU_GATEDIS_CON0 only talks about ungating
clocks. Based on experimentation, we've found that it does not power
up the necessary PLLs.
[1] CHROMIUM: soc: rockchip: power-domain: Add notifier to dmc driver
https://chromium-review.googlesource.com/q/I242dbd706d352f74ff706f5cbf42ebb92f9bcc60
Notably, the Chromium solution only handled conflict (a), not (b).
In practice, item (b) wasn't a problem in many cases because we
never managed to fully power off PLLs. Now that the (upstream) video
decoder driver performs runtime clock management, we often power off
NPLL.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The felix driver is the only user of dsa_port_walk_mdbs(), and there
isn't even a good reason for it, considering that the host MDB entries
are already saved by the ocelot switch lib in the ocelot->multicast list.
Rewrite the multicast entry migration procedure around the
ocelot->multicast list so we can delete dsa_port_walk_mdbs().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since the blamed commit, VCAP filters can appear on more than one list.
If their action is "trap", they are chained on ocelot->traps via
filter->trap_list. This is in addition to their normal placement on the
VCAP block->rules list head.
Therefore, when we free a VCAP filter, we must remove it from all lists
it is a member of, including ocelot->traps.
There are at least 2 bugs which are direct consequences of this design
decision.
First is the incorrect usage of list_empty(), meant to denote whether
"filter" is chained into ocelot->traps via filter->trap_list.
This does not do the correct thing, because list_empty() checks whether
"head->next == head", but in our case, head->next == head->prev == NULL.
So we dereference NULL pointers and die when we call list_del().
Second is the fact that not all places that should remove the filter
from ocelot->traps do so. One example is ocelot_vcap_block_remove_filter(),
which is where we have the main kfree(filter). By keeping freed filters
in ocelot->traps we end up in a use-after-free in
felix_update_trapping_destinations().
Attempting to fix all the buggy patterns is a whack-a-mole game which
makes the driver unmaintainable. Actually this is what the previous
patch version attempted to do:
https://patchwork.kernel.org/project/netdevbpf/patch/20220503115728.834457-3-vladimir.oltean@nxp.com/
but it introduced another set of bugs, because there are other places in
which create VCAP filters, not just ocelot_vcap_filter_create():
- ocelot_trap_add()
- felix_tag_8021q_vlan_add_rx()
- felix_tag_8021q_vlan_add_tx()
Relying on the convention that all those code paths must call
INIT_LIST_HEAD(&filter->trap_list) is not going to scale.
So let's do what should have been done in the first place and keep a
bool in struct ocelot_vcap_filter which denotes whether we are looking
at a trapping rule or not. Iterating now happens over the main VCAP IS2
block->rules. The advantage is that we no longer risk having stale
references to a freed filter, since it is only present in that list.
Fixes: e42bd4ed09 ("net: mscc: ocelot: keep traps in a list")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 2f187bfa6f ("net: ethernet: ocelot: remove the need for num_stats
initializer") added a macro that patchwork warned it lacked parentheses
around an argument. Correct this mistake.
Fixes: 2f187bfa6f ("net: ethernet: ocelot: remove the need for num_stats initializer")
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 2f187bfa6f ("net: ethernet: ocelot: remove the need for num_stats
initializer") added a flags field to the ocelot stats structure. The same
behavior can be achieved without this additional field taking up extra
memory.
Remove this structure element to free up RAM
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a desire to share the oclot_stats_layout struct outside of the
current vsc7514 driver. In order to do so, the length of the array needs to
be known at compile time, and defined in the struct ocelot and struct
felix_info.
Since the array is defined in a .c file and would be declared in the header
file via:
extern struct ocelot_stat_layout[];
the size of the array will not be known at compile time to outside modules.
To fix this, remove the need for defining the number of stats at compile
time and allow this number to be determined at initialization.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dma-buf:
- rename dma-buf-map to iosys-map
core:
- move buddy allocator to core
- add pci/platform init macros
- improve EDID parser deep color handling
- EDID timing type 7 support
- add GPD Win Max quirk
- add yes/no helpers to string_helpers
- flatten syncobj chains
- add nomodeset support to lots of drivers
- improve fb-helper clipping support
- add default property value interface
fbdev:
- improve fbdev ops speed
ttm:
- add a backpointer from ttm bo->ttm resource
dp:
- move displayport headers
- add a dp helper module
bridge:
- anx7625 atomic support, HDCP support
panel:
- split out panel-lvds and lvds bindings
- find panels in OF subnodes
privacy:
- add chromeos privacy screen support
fb:
- hot unplug fw fb on forced removal
simpledrm:
- request region instead of marking ioresource busy
- add panel oreintation property
udmabuf:
- fix oops with 0 pages
amdgpu:
- power management code cleanup
- Enable freesync video mode by default
- RAS code cleanup
- Improve VRAM access for debug using SDMA
- SR-IOV rework special register access and fixes
- profiling power state request ioctl
- expose IP discovery via sysfs
- Cyan skillfish updates
- GC 10.3.7, SDMA 5.2.7, DCN 3.1.6 updates
- expose benchmark tests via debugfs
- add module param to disable XGMI for testing
- GPU reset debugfs register dumping support
amdkfd:
- CRIU support
- SDMA queue fixes
radeon:
- UVD suspend fix
- iMac backlight fix
i915:
- minimal parallel submission for execlists
- DG2-G12 subplatform added
- DG2 programming workarounds
- DG2 accelerated migration support
- flat CCS and CCS engine support for XeHP
- initial small BAR support
- drop fake LMEM support
- ADL-N PCH support
- bigjoiner updates
- introduce VMA resources and async unbinding
- register definitions cleanups
- multi-FBC refactoring
- DG1 OPROM over SPI support
- ADL-N platform enabling
- opregion mailbox #5 support
- DP MST ESI improvements
- drm device based logging
- async flip optimisation for DG2
- CPU arch abstraction fixes
- improve GuC ADS init to work on aarch64
- tweak TTM LRU priority hint
- GuC 69.0.3 support
- remove short term execbuf pins
nouveau:
- higher DP/eDP bitrates
- backlight fixes
msm:
- dpu + dp support for sc8180x
- dp support for sm8350
- dpu + dsi support for qcm2290
- 10nm dsi phy tuning support
- bridge support for dp encoder
- gpu support for additional 7c3 SKUs
ingenic:
- HDMI support for JZ4780
- aux channel EDID support
ast:
- AST2600 support
- add wide screen support
- create DP/DVI connectors
omapdrm:
- fix implicit dma_buf fencing
vc4:
- add CSC + full range support
- better display firmware handoff
panfrost:
- add initial dual-core GPU support
stm:
- new revision support
- fb handover support
mediatek:
- transfer display binding document to yaml format.
- add mt8195 display device binding.
- allow commands to be sent during video mode.
- add wait_for_event for crtc disable by cmdq.
tegra:
- YUV format support
rcar-du:
- LVDS support for M3-W+ (R8A77961)
exynos:
- BGR pixel format for FIMD device
-----BEGIN PGP SIGNATURE-----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=uRsT
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2022-03-24' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Lots of work all over, Intel improving DG2 support, amdkfd CRIU
support, msm new hw support, and faster fbdev support.
dma-buf:
- rename dma-buf-map to iosys-map
core:
- move buddy allocator to core
- add pci/platform init macros
- improve EDID parser deep color handling
- EDID timing type 7 support
- add GPD Win Max quirk
- add yes/no helpers to string_helpers
- flatten syncobj chains
- add nomodeset support to lots of drivers
- improve fb-helper clipping support
- add default property value interface
fbdev:
- improve fbdev ops speed
ttm:
- add a backpointer from ttm bo->ttm resource
dp:
- move displayport headers
- add a dp helper module
bridge:
- anx7625 atomic support, HDCP support
panel:
- split out panel-lvds and lvds bindings
- find panels in OF subnodes
privacy:
- add chromeos privacy screen support
fb:
- hot unplug fw fb on forced removal
simpledrm:
- request region instead of marking ioresource busy
- add panel oreintation property
udmabuf:
- fix oops with 0 pages
amdgpu:
- power management code cleanup
- Enable freesync video mode by default
- RAS code cleanup
- Improve VRAM access for debug using SDMA
- SR-IOV rework special register access and fixes
- profiling power state request ioctl
- expose IP discovery via sysfs
- Cyan skillfish updates
- GC 10.3.7, SDMA 5.2.7, DCN 3.1.6 updates
- expose benchmark tests via debugfs
- add module param to disable XGMI for testing
- GPU reset debugfs register dumping support
amdkfd:
- CRIU support
- SDMA queue fixes
radeon:
- UVD suspend fix
- iMac backlight fix
i915:
- minimal parallel submission for execlists
- DG2-G12 subplatform added
- DG2 programming workarounds
- DG2 accelerated migration support
- flat CCS and CCS engine support for XeHP
- initial small BAR support
- drop fake LMEM support
- ADL-N PCH support
- bigjoiner updates
- introduce VMA resources and async unbinding
- register definitions cleanups
- multi-FBC refactoring
- DG1 OPROM over SPI support
- ADL-N platform enabling
- opregion mailbox #5 support
- DP MST ESI improvements
- drm device based logging
- async flip optimisation for DG2
- CPU arch abstraction fixes
- improve GuC ADS init to work on aarch64
- tweak TTM LRU priority hint
- GuC 69.0.3 support
- remove short term execbuf pins
nouveau:
- higher DP/eDP bitrates
- backlight fixes
msm:
- dpu + dp support for sc8180x
- dp support for sm8350
- dpu + dsi support for qcm2290
- 10nm dsi phy tuning support
- bridge support for dp encoder
- gpu support for additional 7c3 SKUs
ingenic:
- HDMI support for JZ4780
- aux channel EDID support
ast:
- AST2600 support
- add wide screen support
- create DP/DVI connectors
omapdrm:
- fix implicit dma_buf fencing
vc4:
- add CSC + full range support
- better display firmware handoff
panfrost:
- add initial dual-core GPU support
stm:
- new revision support
- fb handover support
mediatek:
- transfer display binding document to yaml format.
- add mt8195 display device binding.
- allow commands to be sent during video mode.
- add wait_for_event for crtc disable by cmdq.
tegra:
- YUV format support
rcar-du:
- LVDS support for M3-W+ (R8A77961)
exynos:
- BGR pixel format for FIMD device"
* tag 'drm-next-2022-03-24' of git://anongit.freedesktop.org/drm/drm: (1529 commits)
drm/i915/display: Do not re-enable PSR after it was marked as not reliable
drm/i915/display: Fix HPD short pulse handling for eDP
drm/amdgpu: Use drm_mode_copy()
drm/radeon: Use drm_mode_copy()
drm/amdgpu: Use ternary operator in `vcn_v1_0_start()`
drm/amdgpu: Remove pointless on stack mode copies
drm/amd/pm: fix indenting in __smu_cmn_reg_print_error()
drm/amdgpu/dc: fix typos in comments
drm/amdgpu: fix typos in comments
drm/amd/pm: fix typos in comments
drm/amdgpu: Add stolen reserved memory for MI25 SRIOV.
drm/amdgpu: Merge get_reserved_allocation to get_vbios_allocations.
drm/amdkfd: evict svm bo worker handle error
drm/amdgpu/vcn: fix vcn ring test failure in igt reload test
drm/amdgpu: only allow secure submission on rings which support that
drm/amdgpu: fixed the warnings reported by kernel test robot
drm/amd/display: 3.2.177
drm/amd/display: [FW Promotion] Release 0.0.108.0
drm/amd/display: Add save/restore PANEL_PWRSEQ_REF_DIV2
drm/amd/display: Wait for hubp read line for Pollock
...
Core
----
- Introduce XDP multi-buffer support, allowing the use of XDP with
jumbo frame MTUs and combination with Rx coalescing offloads (LRO).
- Speed up netns dismantling (5x) and lower the memory cost a little.
Remove unnecessary per-netns sockets. Scope some lists to a netns.
Cut down RCU syncing. Use batch methods. Allow netdev registration
to complete out of order.
- Support distinguishing timestamp types (ingress vs egress) and
maintaining them across packet scrubbing points (e.g. redirect).
- Continue the work of annotating packet drop reasons throughout
the stack.
- Switch netdev error counters from an atomic to dynamically
allocated per-CPU counters.
- Rework a few preempt_disable(), local_irq_save() and busy waiting
sections problematic on PREEMPT_RT.
- Extend the ref_tracker to allow catching use-after-free bugs.
BPF
---
- Introduce "packing allocator" for BPF JIT images. JITed code is
marked read only, and used to be allocated at page granularity.
Custom allocator allows for more efficient memory use, lower
iTLB pressure and prevents identity mapping huge pages from
getting split.
- Make use of BTF type annotations (e.g. __user, __percpu) to enforce
the correct probe read access method, add appropriate helpers.
- Convert the BPF preload to use light skeleton and drop
the user-mode-driver dependency.
- Allow XDP BPF_PROG_RUN test infra to send real packets, enabling
its use as a packet generator.
- Allow local storage memory to be allocated with GFP_KERNEL if called
from a hook allowed to sleep.
- Introduce fprobe (multi kprobe) to speed up mass attachment (arch
bits to come later).
- Add unstable conntrack lookup helpers for BPF by using the BPF
kfunc infra.
- Allow cgroup BPF progs to return custom errors to user space.
- Add support for AF_UNIX iterator batching.
- Allow iterator programs to use sleepable helpers.
- Support JIT of add, and, or, xor and xchg atomic ops on arm64.
- Add BTFGen support to bpftool which allows to use CO-RE in kernels
without BTF info.
- Large number of libbpf API improvements, cleanups and deprecations.
Protocols
---------
- Micro-optimize UDPv6 Tx, gaining up to 5% in test on dummy netdev.
- Adjust TSO packet sizes based on min_rtt, allowing very low latency
links (data centers) to always send full-sized TSO super-frames.
- Make IPv6 flow label changes (AKA hash rethink) more configurable,
via sysctl and setsockopt. Distinguish between server and client
behavior.
- VxLAN support to "collect metadata" devices to terminate only
configured VNIs. This is similar to VLAN filtering in the bridge.
- Support inserting IPv6 IOAM information to a fraction of frames.
- Add protocol attribute to IP addresses to allow identifying where
given address comes from (kernel-generated, DHCP etc.)
- Support setting socket and IPv6 options via cmsg on ping6 sockets.
- Reject mis-use of ECN bits in IP headers as part of DSCP/TOS.
Define dscp_t and stop taking ECN bits into account in fib-rules.
- Add support for locked bridge ports (for 802.1X).
- tun: support NAPI for packets received from batched XDP buffs,
doubling the performance in some scenarios.
- IPv6 extension header handling in Open vSwitch.
- Support IPv6 control message load balancing in bonding, prevent
neighbor solicitation and advertisement from using the wrong port.
Support NS/NA monitor selection similar to existing ARP monitor.
- SMC
- improve performance with TCP_CORK and sendfile()
- support auto-corking
- support TCP_NODELAY
- MCTP (Management Component Transport Protocol)
- add user space tag control interface
- I2C binding driver (as specified by DMTF DSP0237)
- Multi-BSSID beacon handling in AP mode for WiFi.
- Bluetooth:
- handle MSFT Monitor Device Event
- add MGMT Adv Monitor Device Found/Lost events
- Multi-Path TCP:
- add support for the SO_SNDTIMEO socket option
- lots of selftest cleanups and improvements
- Increase the max PDU size in CAN ISOTP to 64 kB.
Driver API
----------
- Add HW counters for SW netdevs, a mechanism for devices which
offload packet forwarding to report packet statistics back to
software interfaces such as tunnels.
- Select the default NIC queue count as a fraction of number of
physical CPU cores, instead of hard-coding to 8.
- Expose devlink instance locks to drivers. Allow device layer of
drivers to use that lock directly instead of creating their own
which always runs into ordering issues in devlink callbacks.
- Add header/data split indication to guide user space enabling
of TCP zero-copy Rx.
- Allow configuring completion queue event size.
- Refactor page_pool to enable fragmenting after allocation.
- Add allocation and page reuse statistics to page_pool.
- Improve Multiple Spanning Trees support in the bridge to allow
reuse of topologies across VLANs, saving HW resources in switches.
- DSA (Distributed Switch Architecture):
- replay and offload of host VLAN entries
- offload of static and local FDB entries on LAG interfaces
- FDB isolation and unicast filtering
New hardware / drivers
----------------------
- Ethernet:
- LAN937x T1 PHYs
- Davicom DM9051 SPI NIC driver
- Realtek RTL8367S, RTL8367RB-VB switch and MDIO
- Microchip ksz8563 switches
- Netronome NFP3800 SmartNICs
- Fungible SmartNICs
- MediaTek MT8195 switches
- WiFi:
- mt76: MediaTek mt7916
- mt76: MediaTek mt7921u USB adapters
- brcmfmac: Broadcom BCM43454/6
- Mobile:
- iosm: Intel M.2 7360 WWAN card
Drivers
-------
- Convert many drivers to the new phylink API built for split PCS
designs but also simplifying other cases.
- Intel Ethernet NICs:
- add TTY for GNSS module for E810T device
- improve AF_XDP performance
- GTP-C and GTP-U filter offload
- QinQ VLAN support
- Mellanox Ethernet NICs (mlx5):
- support xdp->data_meta
- multi-buffer XDP
- offload tc push_eth and pop_eth actions
- Netronome Ethernet NICs (nfp):
- flow-independent tc action hardware offload (police / meter)
- AF_XDP
- Other Ethernet NICs:
- at803x: fiber and SFP support
- xgmac: mdio: preamble suppression and custom MDC frequencies
- r8169: enable ASPM L1.2 if system vendor flags it as safe
- macb/gem: ZynqMP SGMII
- hns3: add TX push mode
- dpaa2-eth: software TSO
- lan743x: multi-queue, mdio, SGMII, PTP
- axienet: NAPI and GRO support
- Mellanox Ethernet switches (mlxsw):
- source and dest IP address rewrites
- RJ45 ports
- Marvell Ethernet switches (prestera):
- basic routing offload
- multi-chain TC ACL offload
- NXP embedded Ethernet switches (ocelot & felix):
- PTP over UDP with the ocelot-8021q DSA tagging protocol
- basic QoS classification on Felix DSA switch using dcbnl
- port mirroring for ocelot switches
- Microchip high-speed industrial Ethernet (sparx5):
- offloading of bridge port flooding flags
- PTP Hardware Clock
- Other embedded switches:
- lan966x: PTP Hardward Clock
- qca8k: mdio read/write operations via crafted Ethernet packets
- Qualcomm 802.11ax WiFi (ath11k):
- add LDPC FEC type and 802.11ax High Efficiency data in radiotap
- enable RX PPDU stats in monitor co-exist mode
- Intel WiFi (iwlwifi):
- UHB TAS enablement via BIOS
- band disablement via BIOS
- channel switch offload
- 32 Rx AMPDU sessions in newer devices
- MediaTek WiFi (mt76):
- background radar detection
- thermal management improvements on mt7915
- SAR support for more mt76 platforms
- MBSSID and 6 GHz band on mt7915
- RealTek WiFi:
- rtw89: AP mode
- rtw89: 160 MHz channels and 6 GHz band
- rtw89: hardware scan
- Bluetooth:
- mt7921s: wake on Bluetooth, SCO over I2S, wide-band-speed (WBS)
- Microchip CAN (mcp251xfd):
- multiple RX-FIFOs and runtime configurable RX/TX rings
- internal PLL, runtime PM handling simplification
- improve chip detection and error handling after wakeup
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=ELpe
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"The sprinkling of SPI drivers is because we added a new one and Mark
sent us a SPI driver interface conversion pull request.
Core
----
- Introduce XDP multi-buffer support, allowing the use of XDP with
jumbo frame MTUs and combination with Rx coalescing offloads (LRO).
- Speed up netns dismantling (5x) and lower the memory cost a little.
Remove unnecessary per-netns sockets. Scope some lists to a netns.
Cut down RCU syncing. Use batch methods. Allow netdev registration
to complete out of order.
- Support distinguishing timestamp types (ingress vs egress) and
maintaining them across packet scrubbing points (e.g. redirect).
- Continue the work of annotating packet drop reasons throughout the
stack.
- Switch netdev error counters from an atomic to dynamically
allocated per-CPU counters.
- Rework a few preempt_disable(), local_irq_save() and busy waiting
sections problematic on PREEMPT_RT.
- Extend the ref_tracker to allow catching use-after-free bugs.
BPF
---
- Introduce "packing allocator" for BPF JIT images. JITed code is
marked read only, and used to be allocated at page granularity.
Custom allocator allows for more efficient memory use, lower iTLB
pressure and prevents identity mapping huge pages from getting
split.
- Make use of BTF type annotations (e.g. __user, __percpu) to enforce
the correct probe read access method, add appropriate helpers.
- Convert the BPF preload to use light skeleton and drop the
user-mode-driver dependency.
- Allow XDP BPF_PROG_RUN test infra to send real packets, enabling
its use as a packet generator.
- Allow local storage memory to be allocated with GFP_KERNEL if
called from a hook allowed to sleep.
- Introduce fprobe (multi kprobe) to speed up mass attachment (arch
bits to come later).
- Add unstable conntrack lookup helpers for BPF by using the BPF
kfunc infra.
- Allow cgroup BPF progs to return custom errors to user space.
- Add support for AF_UNIX iterator batching.
- Allow iterator programs to use sleepable helpers.
- Support JIT of add, and, or, xor and xchg atomic ops on arm64.
- Add BTFGen support to bpftool which allows to use CO-RE in kernels
without BTF info.
- Large number of libbpf API improvements, cleanups and deprecations.
Protocols
---------
- Micro-optimize UDPv6 Tx, gaining up to 5% in test on dummy netdev.
- Adjust TSO packet sizes based on min_rtt, allowing very low latency
links (data centers) to always send full-sized TSO super-frames.
- Make IPv6 flow label changes (AKA hash rethink) more configurable,
via sysctl and setsockopt. Distinguish between server and client
behavior.
- VxLAN support to "collect metadata" devices to terminate only
configured VNIs. This is similar to VLAN filtering in the bridge.
- Support inserting IPv6 IOAM information to a fraction of frames.
- Add protocol attribute to IP addresses to allow identifying where
given address comes from (kernel-generated, DHCP etc.)
- Support setting socket and IPv6 options via cmsg on ping6 sockets.
- Reject mis-use of ECN bits in IP headers as part of DSCP/TOS.
Define dscp_t and stop taking ECN bits into account in fib-rules.
- Add support for locked bridge ports (for 802.1X).
- tun: support NAPI for packets received from batched XDP buffs,
doubling the performance in some scenarios.
- IPv6 extension header handling in Open vSwitch.
- Support IPv6 control message load balancing in bonding, prevent
neighbor solicitation and advertisement from using the wrong port.
Support NS/NA monitor selection similar to existing ARP monitor.
- SMC
- improve performance with TCP_CORK and sendfile()
- support auto-corking
- support TCP_NODELAY
- MCTP (Management Component Transport Protocol)
- add user space tag control interface
- I2C binding driver (as specified by DMTF DSP0237)
- Multi-BSSID beacon handling in AP mode for WiFi.
- Bluetooth:
- handle MSFT Monitor Device Event
- add MGMT Adv Monitor Device Found/Lost events
- Multi-Path TCP:
- add support for the SO_SNDTIMEO socket option
- lots of selftest cleanups and improvements
- Increase the max PDU size in CAN ISOTP to 64 kB.
Driver API
----------
- Add HW counters for SW netdevs, a mechanism for devices which
offload packet forwarding to report packet statistics back to
software interfaces such as tunnels.
- Select the default NIC queue count as a fraction of number of
physical CPU cores, instead of hard-coding to 8.
- Expose devlink instance locks to drivers. Allow device layer of
drivers to use that lock directly instead of creating their own
which always runs into ordering issues in devlink callbacks.
- Add header/data split indication to guide user space enabling of
TCP zero-copy Rx.
- Allow configuring completion queue event size.
- Refactor page_pool to enable fragmenting after allocation.
- Add allocation and page reuse statistics to page_pool.
- Improve Multiple Spanning Trees support in the bridge to allow
reuse of topologies across VLANs, saving HW resources in switches.
- DSA (Distributed Switch Architecture):
- replay and offload of host VLAN entries
- offload of static and local FDB entries on LAG interfaces
- FDB isolation and unicast filtering
New hardware / drivers
----------------------
- Ethernet:
- LAN937x T1 PHYs
- Davicom DM9051 SPI NIC driver
- Realtek RTL8367S, RTL8367RB-VB switch and MDIO
- Microchip ksz8563 switches
- Netronome NFP3800 SmartNICs
- Fungible SmartNICs
- MediaTek MT8195 switches
- WiFi:
- mt76: MediaTek mt7916
- mt76: MediaTek mt7921u USB adapters
- brcmfmac: Broadcom BCM43454/6
- Mobile:
- iosm: Intel M.2 7360 WWAN card
Drivers
-------
- Convert many drivers to the new phylink API built for split PCS
designs but also simplifying other cases.
- Intel Ethernet NICs:
- add TTY for GNSS module for E810T device
- improve AF_XDP performance
- GTP-C and GTP-U filter offload
- QinQ VLAN support
- Mellanox Ethernet NICs (mlx5):
- support xdp->data_meta
- multi-buffer XDP
- offload tc push_eth and pop_eth actions
- Netronome Ethernet NICs (nfp):
- flow-independent tc action hardware offload (police / meter)
- AF_XDP
- Other Ethernet NICs:
- at803x: fiber and SFP support
- xgmac: mdio: preamble suppression and custom MDC frequencies
- r8169: enable ASPM L1.2 if system vendor flags it as safe
- macb/gem: ZynqMP SGMII
- hns3: add TX push mode
- dpaa2-eth: software TSO
- lan743x: multi-queue, mdio, SGMII, PTP
- axienet: NAPI and GRO support
- Mellanox Ethernet switches (mlxsw):
- source and dest IP address rewrites
- RJ45 ports
- Marvell Ethernet switches (prestera):
- basic routing offload
- multi-chain TC ACL offload
- NXP embedded Ethernet switches (ocelot & felix):
- PTP over UDP with the ocelot-8021q DSA tagging protocol
- basic QoS classification on Felix DSA switch using dcbnl
- port mirroring for ocelot switches
- Microchip high-speed industrial Ethernet (sparx5):
- offloading of bridge port flooding flags
- PTP Hardware Clock
- Other embedded switches:
- lan966x: PTP Hardward Clock
- qca8k: mdio read/write operations via crafted Ethernet packets
- Qualcomm 802.11ax WiFi (ath11k):
- add LDPC FEC type and 802.11ax High Efficiency data in radiotap
- enable RX PPDU stats in monitor co-exist mode
- Intel WiFi (iwlwifi):
- UHB TAS enablement via BIOS
- band disablement via BIOS
- channel switch offload
- 32 Rx AMPDU sessions in newer devices
- MediaTek WiFi (mt76):
- background radar detection
- thermal management improvements on mt7915
- SAR support for more mt76 platforms
- MBSSID and 6 GHz band on mt7915
- RealTek WiFi:
- rtw89: AP mode
- rtw89: 160 MHz channels and 6 GHz band
- rtw89: hardware scan
- Bluetooth:
- mt7921s: wake on Bluetooth, SCO over I2S, wide-band-speed (WBS)
- Microchip CAN (mcp251xfd):
- multiple RX-FIFOs and runtime configurable RX/TX rings
- internal PLL, runtime PM handling simplification
- improve chip detection and error handling after wakeup"
* tag 'net-next-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2521 commits)
llc: fix netdevice reference leaks in llc_ui_bind()
drivers: ethernet: cpsw: fix panic when interrupt coaleceing is set via ethtool
ice: don't allow to run ice_send_event_to_aux() in atomic ctx
ice: fix 'scheduling while atomic' on aux critical err interrupt
net/sched: fix incorrect vlan_push_eth dest field
net: bridge: mst: Restrict info size queries to bridge ports
net: marvell: prestera: add missing destroy_workqueue() in prestera_module_init()
drivers: net: xgene: Fix regression in CRC stripping
net: geneve: add missing netlink policy and size for IFLA_GENEVE_INNER_PROTO_INHERIT
net: dsa: fix missing host-filtered multicast addresses
net/mlx5e: Fix build warning, detected write beyond size of field
iwlwifi: mvm: Don't fail if PPAG isn't supported
selftests/bpf: Fix kprobe_multi test.
Revert "rethook: x86: Add rethook x86 implementation"
Revert "arm64: rethook: Add arm64 rethook implementation"
Revert "powerpc: Add rethook support"
Revert "ARM: rethook: Add rethook arm implementation"
netdevice: add missing dm_private kdoc
net: bridge: mst: prevent NULL deref in br_mst_info_size()
selftests: forwarding: Use same VRF for port and VLAN upper
...
There are a few separately maintained driver subsystems that we merge through
the SoC tree, notable changes are:
- Memory controller updates, mainly for Tegra and Mediatek SoCs,
and clarifications for the memory controller DT bindings
- SCMI firmware interface updates, in particular a new transport based
on OPTEE and support for atomic operations.
- Cleanups to the TEE subsystem, refactoring its memory management
For SoC specific drivers without a separate subsystem, changes include
- Smaller updates and fixes for TI, AT91/SAMA5, Qualcomm and NXP
Layerscape SoCs.
- Driver support for Microchip SAMA5D29, Tesla FSD, Renesas RZ/G2L,
and Qualcomm SM8450.
- Better power management on Mediatek MT81xx, NXP i.MX8MQ
and older NVIDIA Tegra chips
-----BEGIN PGP SIGNATURE-----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=Cfbk
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM driver updates from Arnd Bergmann:
"There are a few separately maintained driver subsystems that we merge
through the SoC tree, notable changes are:
- Memory controller updates, mainly for Tegra and Mediatek SoCs, and
clarifications for the memory controller DT bindings
- SCMI firmware interface updates, in particular a new transport
based on OPTEE and support for atomic operations.
- Cleanups to the TEE subsystem, refactoring its memory management
For SoC specific drivers without a separate subsystem, changes include
- Smaller updates and fixes for TI, AT91/SAMA5, Qualcomm and NXP
Layerscape SoCs.
- Driver support for Microchip SAMA5D29, Tesla FSD, Renesas RZ/G2L,
and Qualcomm SM8450.
- Better power management on Mediatek MT81xx, NXP i.MX8MQ and older
NVIDIA Tegra chips"
* tag 'arm-drivers-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (154 commits)
ARM: spear: fix typos in comments
soc/microchip: fix invalid free in mpfs_sys_controller_delete
soc: s4: Add support for power domains controller
dt-bindings: power: add Amlogic s4 power domains bindings
ARM: at91: add support in soc driver for new SAMA5D29
soc: mediatek: mmsys: add sw0_rst_offset in mmsys driver data
dt-bindings: memory: renesas,rpc-if: Document RZ/V2L SoC
memory: emif: check the pointer temp in get_device_details()
memory: emif: Add check for setup_interrupts
dt-bindings: arm: mediatek: mmsys: add support for MT8186
dt-bindings: mediatek: add compatible for MT8186 pwrap
soc: mediatek: pwrap: add pwrap driver for MT8186 SoC
soc: mediatek: mmsys: add mmsys reset control for MT8186
soc: mediatek: mtk-infracfg: Disable ACP on MT8192
soc: ti: k3-socinfo: Add AM62x JTAG ID
soc: mediatek: add MTK mutex support for MT8186
soc: mediatek: mmsys: add mt8186 mmsys routing table
soc: mediatek: pm-domains: Add support for mt8186
dt-bindings: power: Add MT8186 power domains
soc: mediatek: pm-domains: Add support for mt8195
...
SoC specific code is generally used for older platforms that don't (yet)
use device tree to do the same things.
- Support is added for i.MXRT10xx, a Cortex-M7 based microcontroller
from NXP. At the moment this is still incomplete as other portions
are merged through different trees.
- Long abandoned support for running NOMMU ARMv4 or ARMv5 platforms
gets removed, now the Arm NOMMU platforms are limited to the
Cortex-M family of microcontrollers
- Two old PXA boards get removed, along with corresponding driver
bits.
- Continued cleanup of the Intel IXP4xx platforms, removing some
remnants of the old board files.
- Minor Cleanups and fixes for Orion, PXA, MMP, Mstar, Samsung
- CPU idle support for AT91
- A system controller driver for Polarfire
-----BEGIN PGP SIGNATURE-----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=2fmA
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"SoC specific code is generally used for older platforms that don't
(yet) use device tree to do the same things.
- Support is added for i.MXRT10xx, a Cortex-M7 based microcontroller
from NXP. At the moment this is still incomplete as other portions
are merged through different trees.
- Long abandoned support for running NOMMU ARMv4 or ARMv5 platforms
gets removed, now the Arm NOMMU platforms are limited to the
Cortex-M family of microcontrollers
- Two old PXA boards get removed, along with corresponding driver
bits.
- Continued cleanup of the Intel IXP4xx platforms, removing some
remnants of the old board files.
- Minor Cleanups and fixes for Orion, PXA, MMP, Mstar, Samsung
- CPU idle support for AT91
- A system controller driver for Polarfire"
* tag 'arm-soc-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (29 commits)
ARM: remove support for NOMMU ARMv4/v5
ARM: PXA: fix up decompressor code
soc: microchip: make mpfs_sys_controller_put static
ARM: pxa: remove Intel Imote2 and Stargate 2 boards
ARM: mmp: Fix failure to remove sram device
ARM: mstar: Select ARM_ERRATA_814220
soc: add microchip polarfire soc system controller
ARM: at91: Kconfig: select PM_OPP
ARM: at91: PM: add cpu idle support for sama7g5
ARM: at91: ddr: fix typo to align with datasheet naming
ARM: at91: ddr: align macro definitions
ARM: at91: ddr: remove CONFIG_SOC_SAMA7 dependency
ARM: ixp4xx: Convert to SPARSE_IRQ and P2V
ARM: ixp4xx: Drop all common code
ARM: ixp4xx: Drop custom DMA coherency and bouncing
ARM: ixp4xx: Remove feature bit accessors
net: ixp4xx_hss: Check features using syscon
net: ixp4xx_eth: Drop platform data support
soc: ixp4xx-npe: Access syscon regs using regmap
soc: ixp4xx: Add features from regmap helper
...
-----BEGIN PGP SIGNATURE-----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=Bc0l
-----END PGP SIGNATURE-----
Merge tag 'media/v5.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- a major reorg at platform Kconfig/Makefile files, organizing them per
vendor. The other media Kconfig/Makefile files also sorted
- New sensor drivers: hi847, isl7998x, ov08d10
- New Amphion vpu decoder stateful driver
- New Atmel microchip csi2dc driver
- tegra-vde driver promoted from staging
- atomisp: some fixes for it to work on BYT
- imx7-mipi-csis driver promoted from staging and renamed
- camss driver got initial support for VFE hardware version Titan 480
- mtk-vcodec has gained support for MT8192
- lots of driver changes, fixes and improvements
* tag 'media/v5.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (417 commits)
media: nxp: Restrict VIDEO_IMX_MIPI_CSIS to ARCH_MXC or COMPILE_TEST
media: amphion: cleanup media device if register it fail
media: amphion: fix some issues to improve robust
media: amphion: fix some error related with undefined reference to __divdi3
media: amphion: fix an issue that using pm_runtime_get_sync incorrectly
media: vidtv: use vfree() for memory allocated with vzalloc()
media: m5mols/m5mols.h: document new reset field
media: pixfmt-yuv-planar.rst: fix PIX_FMT labels
media: platform: Remove unnecessary print function dev_err()
media: amphion: Add missing of_node_put() in vpu_core_parse_dt()
media: mtk-vcodec: Add missing of_node_put() in mtk_vdec_hw_prob_done()
media: platform: amphion: Fix build error without MAILBOX
media: spi: Kconfig: Place SPI drivers on a single menu
media: i2c: Kconfig: move camera drivers to the top
media: atomisp: fix bad usage at error handling logic
media: platform: rename mediatek/mtk-jpeg/ to mediatek/jpeg/
media: media/*/Kconfig: sort entries
media: Kconfig: cleanup VIDEO_DEV dependencies
media: platform/*/Kconfig: make manufacturer menus more uniform
media: platform: Create vendor/{Makefile,Kconfig} files
...
Per-flow mirroring with the VCAP IS2 TCAM (in itself handled as an
offload for tc-flower) is done by setting the MIRROR_ENA bit from the
action vector of the filter. The packet is mirrored to the port mask
configured in the ANA:ANA:MIRRORPORTS register (the same port mask as
the destinations for port-based mirroring).
Functionality was tested with:
tc qdisc add dev swp3 clsact
tc filter add dev swp3 ingress protocol ip \
flower skip_sw ip_proto icmp \
action mirred egress mirror dev swp1
and pinging through swp3, while seeing that the ICMP replies are
mirrored towards swp1.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ocelot switches perform port-based ingress mirroring if
ANA:PORT:PORT_CFG field SRC_MIRROR_ENA is set, and egress mirroring if
the port is in ANA:ANA:EMIRRORPORTS.
Both ingress-mirrored and egress-mirrored frames are copied to the port
mask from ANA:ANA:MIRRORPORTS.
So the choice of limiting to a single mirror port via ocelot_mirror_get()
and ocelot_mirror_put() may seem bizarre, but the hardware model doesn't
map very well to the user space model. If the user wants to mirror the
ingress of swp1 towards swp2 and the ingress of swp3 towards swp4, we'd
have to program ANA:ANA:MIRRORPORTS with BIT(2) | BIT(4), and that would
make swp1 be mirrored towards swp4 too, and swp3 towards swp2. But there
are no tc-matchall rules to describe those actions.
Now, we could offload a matchall rule with multiple mirred actions, one
per desired mirror port, and force the user to stick to the multi-action
rule format for subsequent matchall filters. But both DSA and ocelot
have the flow_offload_has_one_action() check for the matchall offload,
plus the fact that it will get cumbersome to cross-check matchall
mirrors with flower mirrors (which will be added in the next patch).
As a result, we limit the configuration to a single mirror port, with
the possibility of lifting the restriction in the future.
Frames injected from the CPU don't get egress-mirrored, since they are
sent with the BYPASS bit in the injection frame header, and this
bypasses the analyzer module (effectively also the mirroring logic).
I don't know what to do/say about this.
Functionality was tested with:
tc qdisc add dev swp3 clsact
tc filter add dev swp3 ingress \
matchall skip_sw \
action mirred egress mirror dev swp1
and pinging through swp3, while seeing that the ICMP replies are
mirrored towards swp1.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Follow the established programming model for this driver and provide
shims in the felix DSA driver which call the implementations from the
ocelot switch lib. The ocelot switchdev driver wasn't integrated with
dcbnl due to lack of hardware availability.
The switch doesn't have any fancy QoS classification enabled by default.
The provided getters will create a default-prio app table entry of 0,
and no dscp entry. However, the getters have been made to actually
retrieve the hardware configuration rather than static values, to be
future proof in case DSA will need this information from more call paths.
For default-prio, there is a single field per port, in ANA_PORT_QOS_CFG,
called QOS_DEFAULT_VAL.
DSCP classification is enabled per-port, again via ANA_PORT_QOS_CFG
(field QOS_DSCP_ENA), and individual DSCP values are configured as
trusted or not through register ANA_DSCP_CFG (replicated 64 times).
An untrusted DSCP value falls back to other QoS classification methods.
If trusted, the selected ANA_DSCP_CFG register also holds the QoS class
in the QOS_DSCP_VAL field.
The hardware also supports DSCP remapping (DSCP value X is translated to
DSCP value Y before the QoS class is determined based on the app table
entry for Y) and DSCP packet rewriting. The dcbnl framework, for being
so flexible in other useless areas, doesn't appear to support this.
So this functionality has been left out.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently ocelot uses a pvid of 0 for standalone ports and ports under a
VLAN-unaware bridge, and the pvid of the bridge for ports under a
VLAN-aware bridge. Standalone ports do not perform learning, but packets
received on them are still subject to FDB lookups. So if the MAC DA that
a standalone port receives has been also learned on a VLAN-unaware
bridge port, ocelot will attempt to forward to that port, even though it
can't, so it will drop packets.
So there is a desire to avoid that, and isolate the FDBs of different
bridges from one another, and from standalone ports.
The ocelot switch library has two distinct entry points: the felix DSA
driver and the ocelot switchdev driver.
We need to code up a minimal bridge_num allocation in the ocelot
switchdev driver too, this is copied from DSA with the exception that
ocelot does not care about DSA trees, cross-chip bridging etc. So it
only looks at its own ports that are already in the same bridge.
The ocelot switchdev driver uses the bridge_num it has allocated itself,
while the felix driver uses the bridge_num allocated by DSA. They are
both stored inside ocelot_port->bridge_num by the common function
ocelot_port_bridge_join() which receives the bridge_num passed by value.
Once we have a bridge_num, we can only use it to enforce isolation
between VLAN-unaware bridges. As far as I can see, ocelot does not have
anything like a FID that further makes VLAN 100 from a port be different
to VLAN 100 from another port with regard to FDB lookup. So we simply
deny multiple VLAN-aware bridges.
For VLAN-unaware bridges, we crop the 4000-4095 VLAN region and we
allocate a VLAN for each bridge_num. This will be used as the pvid of
each port that is under that VLAN-unaware bridge, for as long as that
bridge is VLAN-unaware.
VID 0 remains only for standalone ports. It is okay if all standalone
ports use the same VID 0, since they perform no address learning, the
FDB will contain no entry in VLAN 0, so the packets will always be
flooded to the only possible destination, the CPU port.
The CPU port module doesn't need to be member of the VLANs to receive
packets, but if we use the DSA tag_8021q protocol, those packets are
part of the data plane as far as ocelot is concerned, so there it needs
to. Just ensure that the DSA tag_8021q CPU port is a member of all
reserved VLANs when it is created, and is removed when it is deleted.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver provides an interface for other drivers to access the
functions of the system controller on the Microchip PolarFire SoC.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20220217101349.2374873-2-conor.dooley@microchip.com
Add CPU idle support for SAMA7G5. Support will make use of PMC_CPU_RATIO
register to divide the CPU clock by 16 before switching it to idle and
use automatic self-refresh option of DDR controller.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20220113144900.906370-5-claudiu.beznea@microchip.com
Remove CONFIG_SOC_SAMA7 dependency to avoid having #ifdef preprocessor
directives in driver code (arch/arm/mach-at91/pm.c). This prepares the
code for next commits.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20220113144900.906370-2-claudiu.beznea@microchip.com
This adds the logic in the Felix DSA driver and Ocelot switch library.
For Ocelot switches, the DEST_IDX that is the output of the MAC table
lookup is a logical port (equal to physical port, if no LAG is used, or
a dynamically allocated number otherwise). The allocation we have in
place for LAG IDs is different from DSA's, so we can't use that:
- DSA allocates a continuous range of LAG IDs starting from 1
- Ocelot appears to require that physical ports and LAG IDs are in the
same space of [0, num_phys_ports), and additionally, ports that aren't
in a LAG must have physical port id == logical port id
The implication is that an FDB entry towards a LAG might need to be
deleted and reinstalled when the LAG ID changes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When kernel.h is used in the headers it adds a lot into dependency hell,
especially when there are circular dependencies are involved.
Replace kernel.h inclusion with the list of what is really being used.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Historically, the felix DSA driver has installed special traps such that
PTP over L2 works with the ocelot-8021q tagging protocol; commit
0a6f17c6ae ("net: dsa: tag_ocelot_8021q: add support for PTP
timestamping") has the details.
Then the ocelot switch library also gained more comprehensive support
for PTP traps through commit 96ca08c058 ("net: mscc: ocelot: set up
traps for PTP packets").
Right now, PTP over L2 works using ocelot-8021q via the traps it has set
for itself, but nothing else does. Consolidating the two code blocks
would make ocelot-8021q gain support for PTP over L4 and tc-flower
traps, and at the same time avoid some code and TCAM duplication.
The traps are similar in intent, but different in execution, so some
explanation is required. The traps set up by felix_setup_mmio_filtering()
are VCAP IS1 filters, which have a PAG that chains them to a VCAP IS2
filter, and the IS2 is where the 'trap' action resides. The traps set up
by ocelot_trap_add(), on the other hand, have a single filter, in VCAP
IS2. The reason for chaining VCAP IS1 and IS2 in Felix was to ensure
that the hardcoded traps take precedence and cannot be overridden by the
Ocelot switch library.
So in principle, the PTP traps needed for ocelot-8021q in the Felix
driver can rely on ocelot_trap_add(), but the filters need to be patched
to account for a quirk that LS1028A has: the quirk_no_xtr_irq described
in commit 0a6f17c6ae ("net: dsa: tag_ocelot_8021q: add support for PTP
timestamping"). Live-patching is done by iterating through the trap list
every time we know it has been updated, and transforming a trap into a
redirect + CPU copy if ocelot-8021q is in use.
Making the DSA ocelot-8021q tagger work with the Ocelot traps means we
can eliminate the dedicated OCELOT_VCAP_IS1_TAG_8021Q_PTP_MMIO and
OCELOT_VCAP_IS2_TAG_8021Q_PTP_MMIO cookies. To minimize the patch delta,
OCELOT_VCAP_IS2_MRP_TRAP takes the place of OCELOT_VCAP_IS2_TAG_8021Q_PTP_MMIO
(the alternative would have been to left-shift all cookie numbers by 1).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot switch library does not need this information, but the felix
DSA driver does.
As a reminder, the VSC9959 switch in LS1028A doesn't have an IRQ line
for packet extraction, so to be notified that a PTP packet needs to be
dequeued, it receives that packet also over Ethernet, by setting up a
packet trap. The Felix driver needs to install special kinds of traps
for packets in need of RX timestamps, such that the packets are
replicated both over Ethernet and over the CPU port module.
But the Ocelot switch library sets up more than one trap for PTP event
messages; it also traps PTP general messages, MRP control messages etc.
Those packets don't need PTP timestamps, so there's no reason for the
Felix driver to send them to the CPU port module.
By knowing which traps need PTP timestamps, the Felix driver can
adjust the traps installed using ocelot_trap_add() such that only those
will actually get delivered to the CPU port module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using the ocelot-8021q tagging protocol, the CPU port isn't
configured as an NPI port, but is a regular port. So a "trap to CPU"
operation is actually a "redirect" operation. So DSA needs to set up the
trapping action one way or another, depending on the tagging protocol in
use.
To ease DSA's work of modifying the action, keep all currently installed
traps in a list, so that DSA can live-patch them when the tagging
protocol changes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OCELOT_VCAP_IS2_TAG_8021Q_TXVLAN overlaps with OCELOT_VCAP_IS2_MRP_REDIRECT.
To avoid this, make OCELOT_VCAP_IS2_MRP_REDIRECT take the cookie region
from N to 2 * N - 1 (where N is ocelot->num_phys_ports).
To avoid any risk that the singleton (not per port) VCAP IS2 filters
overlap with per-port VCAP IS2 filters, we must ensure that the number
of singleton filters is smaller than the number of physical ports.
This is true right now, but may change in the future as switches with
less ports get supported, or more singleton filters get added. So to be
future-proof, let's move the singleton filters at the end of the range,
where they won't overlap with anything to their right.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MRP assist code installs a VCAP IS2 trapping rule for each port, but
since the key and the action is the same, just the ingress port mask
differs, there isn't any need to do this. We can save some space in the
TCAM by using a single filter and adjusting the ingress port mask.
Reuse the ocelot_trap_add() and ocelot_trap_del() functions for this
purpose.
Now that the cookies are no longer per port, we need to change the
allocation scheme such that MRP traps use a fixed number.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MRP frames are configured to be trapped to the CPU queue 7, and this
number is reflected in the extraction header. However, the information
isn't used anywhere, so just leave MRP frames to go to CPU queue 0
unless needed otherwise.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every use case that needed VCAP filters (in order: DSA tag_8021q, MRP,
PTP traps) has hardcoded filter identifiers that worked well enough for
that use case alone. But when two or more of those use cases would be
used together, some of those identifiers would overlap, leading to
breakage.
Add definitions for each cookie and centralize them in ocelot_vcap.h,
such that the overlaps are more obvious.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create and utilize bulk regmap reads instead of single access for gathering
stats. The background reading of statistics happens frequently, and over
a few contiguous memory regions.
High speed PCIe buses and MMIO access will probably see negligible
performance increase. Lower speed buses like SPI and I2C could see
significant performance increase, since the bus configuration and register
access times account for a large percentage of data transfer time.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Regmap supports bulk register reads. Ocelot does not. This patch adds
support for Ocelot to invoke bulk regmap reads. That will allow any driver
that performs consecutive reads over memory regions to optimize that
access.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the ocelot.h file, several read / write macros were split across
multiple lines, while others weren't. Split all macros that exceed the 80
character column width and match the style of the rest of the file.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UAPI Changes:
- Fix invalid IN_FORMATS blob when plane->format_mod_supported is NULL.
Cross-subsystem Changes:
- Assorted dt bindings updates.
- Fix vga16fb vga checking on x86.
- Fix extra semicolon in rwsem.h's _down_write_nest_lock.
- Assorted small fixes to agp and fbdev drivers.
- Fix oops in creating a udmabuf with 0 pages.
- Hot-unplug firmware fb devices on forced removal
- Reqquest memory region in simplefb and simpledrm, and don't make the ioresource as busy.
Core Changes:
- Mock a drm_plane in drm-plane-helper selftest.
- Assorted bug fixes to device logging, dbi.
- Use DP helper for sink count in mst.
- Assorted documentation fixes.
- Assorted small fixes.
- Move DP headers to drm/dp, and add a drm dp helper module.
- Move the buddy allocator from i915 to common drm.
- Add simple pci and platform module init macros to remove a lot of boilerplate from some drivers.
- Support microsoft extension for HMDs and specialized monitors.
- Improve edid parser's deep color handling.
- Add type 7 timing support to edid parser.
- Add a weak backpointer to the ttm_bo from ttm_resource
- Add 3 eDP panels.
Driver Changes:
- Add support for HDMI and JZ4780 to ingenic.
- Add support for higher DP/eDP bitrates to nouveau.
- Assorted driver fixes to tilcdc, vmwgfx, sn65dsi83, meson, stm, panfrost, v3d, gma500, vc4, virtio, mgag200, ast, radeon, amdgpu, nouveau, various bridge drivers.
- Convert and revert exynos dsi support to bridge driver.
- Add vcc supply regulator support for sn65dsi83.
- More conversion of bridge/chipone-icn6211 to atomic.
- Remove conflicting fb's from stm, and add support for new hw version.
- Add device link in parade-ps8640 to fix suspend/resume.
- Update Boe-tv110c9m init sequence.
- Add wide screen support to AST2600.
- Fix omapdrm implicit dma_buf fencing.
- Add support for multiple overlay planes to vkms.
- Convert bridge/anx7625 to atomic, add HDCP support,
add eld support for audio, and fix HPD.
- Add driver for ChromeOS privacy screen.
- Handover display from firmware to vc4 more gracefully, and support nomodeset.
- Add flexible and ycbcr pixel formats to stm/ltdc.
- Convert exynos mipi dsi to atomic.
- Add initial dual core group GPUs support to panfrost.
- No longer add exclusive fence in amdgpu as shared fence.
- Add CSC and full range supoprt to vc4.
- Shutdown the display on system shutdown and unbind.
- Add Multi-Inno Technology MI0700S4T-6 simple panel.
-----BEGIN PGP SIGNATURE-----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=IMtm
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2022-01-27' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
[airlied: add two missing Kconfig]
drm-misc-next for v5.18:
UAPI Changes:
- Fix invalid IN_FORMATS blob when plane->format_mod_supported is NULL.
Cross-subsystem Changes:
- Assorted dt bindings updates.
- Fix vga16fb vga checking on x86.
- Fix extra semicolon in rwsem.h's _down_write_nest_lock.
- Assorted small fixes to agp and fbdev drivers.
- Fix oops in creating a udmabuf with 0 pages.
- Hot-unplug firmware fb devices on forced removal
- Reqquest memory region in simplefb and simpledrm, and don't make the ioresource as busy.
Core Changes:
- Mock a drm_plane in drm-plane-helper selftest.
- Assorted bug fixes to device logging, dbi.
- Use DP helper for sink count in mst.
- Assorted documentation fixes.
- Assorted small fixes.
- Move DP headers to drm/dp, and add a drm dp helper module.
- Move the buddy allocator from i915 to common drm.
- Add simple pci and platform module init macros to remove a lot of boilerplate from some drivers.
- Support microsoft extension for HMDs and specialized monitors.
- Improve edid parser's deep color handling.
- Add type 7 timing support to edid parser.
- Add a weak backpointer to the ttm_bo from ttm_resource
- Add 3 eDP panels.
Driver Changes:
- Add support for HDMI and JZ4780 to ingenic.
- Add support for higher DP/eDP bitrates to nouveau.
- Assorted driver fixes to tilcdc, vmwgfx, sn65dsi83, meson, stm, panfrost, v3d, gma500, vc4, virtio, mgag200, ast, radeon, amdgpu, nouveau, various bridge drivers.
- Convert and revert exynos dsi support to bridge driver.
- Add vcc supply regulator support for sn65dsi83.
- More conversion of bridge/chipone-icn6211 to atomic.
- Remove conflicting fb's from stm, and add support for new hw version.
- Add device link in parade-ps8640 to fix suspend/resume.
- Update Boe-tv110c9m init sequence.
- Add wide screen support to AST2600.
- Fix omapdrm implicit dma_buf fencing.
- Add support for multiple overlay planes to vkms.
- Convert bridge/anx7625 to atomic, add HDCP support,
add eld support for audio, and fix HPD.
- Add driver for ChromeOS privacy screen.
- Handover display from firmware to vc4 more gracefully, and support nomodeset.
- Add flexible and ycbcr pixel formats to stm/ltdc.
- Convert exynos mipi dsi to atomic.
- Add initial dual core group GPUs support to panfrost.
- No longer add exclusive fence in amdgpu as shared fence.
- Add CSC and full range supoprt to vc4.
- Shutdown the display on system shutdown and unbind.
- Add Multi-Inno Technology MI0700S4T-6 simple panel.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/456a23c6-7324-7543-0c45-751f30ef83f7@linux.intel.com
After adding device_link between the iommu consumer and smi-larb,
the pm_runtime_get(_sync) of smi-larb and smi-common will be called
automatically. we can get rid of mtk_smi_larb_get/put.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de> # BPI-R2/MT7623
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The RPI_FIRMWARE_NOTIFY_DISPLAY_DONE firmware call allows to tell the
firmware the kernel is in charge of the display now and the firmware can
free whatever resources it was using.
Acked-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20211215095117.176435-2-maxime@cerno.tech
Core
----
- Defer freeing TCP skbs to the BH handler, whenever possible,
or at least perform the freeing outside of the socket lock section
to decrease cross-CPU allocator work and improve latency.
- Add netdevice refcount tracking to locate sources of netdevice
and net namespace refcount leaks.
- Make Tx watchdog less intrusive - avoid pausing Tx and restarting
all queues from a single CPU removing latency spikes.
- Various small optimizations throughout the stack from Eric Dumazet.
- Make netdev->dev_addr[] constant, force modifications to go via
appropriate helpers to allow us to keep addresses in ordered data
structures.
- Replace unix_table_lock with per-hash locks, improving performance
of bind() calls.
- Extend skb drop tracepoint with a drop reason.
- Allow SO_MARK and SO_PRIORITY setsockopt under CAP_NET_RAW.
BPF
---
- New helpers:
- bpf_find_vma(), find and inspect VMAs for profiling use cases
- bpf_loop(), runtime-bounded loop helper trading some execution
time for much faster (if at all converging) verification
- bpf_strncmp(), improve performance, avoid compiler flakiness
- bpf_get_func_arg(), bpf_get_func_ret(), bpf_get_func_arg_cnt()
for tracing programs, all inlined by the verifier
- Support BPF relocations (CO-RE) in the kernel loader.
- Further the support for BTF_TYPE_TAG annotations.
- Allow access to local storage in sleepable helpers.
- Convert verifier argument types to a composable form with different
attributes which can be shared across types (ro, maybe-null).
- Prepare libbpf for upcoming v1.0 release by cleaning up APIs,
creating new, extensible ones where missing and deprecating those
to be removed.
Protocols
---------
- WiFi (mac80211/cfg80211):
- notify user space about long "come back in N" AP responses,
allow it to react to such temporary rejections
- allow non-standard VHT MCS 10/11 rates
- use coarse time in airtime fairness code to save CPU cycles
- Bluetooth:
- rework of HCI command execution serialization to use a common
queue and work struct, and improve handling errors reported
in the middle of a batch of commands
- rework HCI event handling to use skb_pull_data, avoiding packet
parsing pitfalls
- support AOSP Bluetooth Quality Report
- SMC:
- support net namespaces, following the RDMA model
- improve connection establishment latency by pre-clearing buffers
- introduce TCP ULP for automatic redirection to SMC
- Multi-Path TCP:
- support ioctls: SIOCINQ, OUTQ, and OUTQNSD
- support socket options: IP_TOS, IP_FREEBIND, IP_TRANSPARENT,
IPV6_FREEBIND, and IPV6_TRANSPARENT, TCP_CORK and TCP_NODELAY
- support cmsgs: TCP_INQ
- improvements in the data scheduler (assigning data to subflows)
- support fastclose option (quick shutdown of the full MPTCP
connection, similar to TCP RST in regular TCP)
- MCTP (Management Component Transport) over serial, as defined by
DMTF spec DSP0253 - "MCTP Serial Transport Binding".
Driver API
----------
- Support timestamping on bond interfaces in active/passive mode.
- Introduce generic phylink link mode validation for drivers which
don't have any quirks and where MAC capability bits fully express
what's supported. Allow PCS layer to participate in the validation.
Convert a number of drivers.
- Add support to set/get size of buffers on the Rx rings and size of
the tx copybreak buffer via ethtool.
- Support offloading TC actions as first-class citizens rather than
only as attributes of filters, improve sharing and device resource
utilization.
- WiFi (mac80211/cfg80211):
- support forwarding offload (ndo_fill_forward_path)
- support for background radar detection hardware
- SA Query Procedures offload on the AP side
New hardware / drivers
----------------------
- tsnep - FPGA based TSN endpoint Ethernet MAC used in PLCs with
real-time requirements for isochronous communication with protocols
like OPC UA Pub/Sub.
- Qualcomm BAM-DMUX WWAN - driver for data channels of modems
integrated into many older Qualcomm SoCs, e.g. MSM8916 or
MSM8974 (qcom_bam_dmux).
- Microchip LAN966x multi-port Gigabit AVB/TSN Ethernet Switch
driver with support for bridging, VLANs and multicast forwarding
(lan966x).
- iwlmei driver for co-operating between Intel's WiFi driver and
Intel's Active Management Technology (AMT) devices.
- mse102x - Vertexcom MSE102x Homeplug GreenPHY chips
- Bluetooth:
- MediaTek MT7921 SDIO devices
- Foxconn MT7922A
- Realtek RTL8852AE
Drivers
-------
- Significantly improve performance in the datapaths of:
lan78xx, ax88179_178a, lantiq_xrx200, bnxt.
- Intel Ethernet NICs:
- igb: support PTP/time PEROUT and EXTTS SDP functions on
82580/i354/i350 adapters
- ixgbevf: new PF -> VF mailbox API which avoids the risk of
mailbox corruption with ESXi
- iavf: support configuration of VLAN features of finer granularity,
stacked tags and filtering
- ice: PTP support for new E822 devices with sub-ns precision
- ice: support firmware activation without reboot
- Mellanox Ethernet NICs (mlx5):
- expose control over IRQ coalescing mode (CQE vs EQE) via ethtool
- support TC forwarding when tunnel encap and decap happen between
two ports of the same NIC
- dynamically size and allow disabling various features to save
resources for running in embedded / SmartNIC scenarios
- Broadcom Ethernet NICs (bnxt):
- use page frag allocator to improve Rx performance
- expose control over IRQ coalescing mode (CQE vs EQE) via ethtool
- Other Ethernet NICs:
- amd-xgbe: add Ryzen 6000 (Yellow Carp) Ethernet support
- Microsoft cloud/virtual NIC (mana):
- add XDP support (PASS, DROP, TX)
- Mellanox Ethernet switches (mlxsw):
- initial support for Spectrum-4 ASICs
- VxLAN with IPv6 underlay
- Marvell Ethernet switches (prestera):
- support flower flow templates
- add basic IP forwarding support
- NXP embedded Ethernet switches (ocelot & felix):
- support Per-Stream Filtering and Policing (PSFP)
- enable cut-through forwarding between ports by default
- support FDMA to improve packet Rx/Tx to CPU
- Other embedded switches:
- hellcreek: improve trapping management (STP and PTP) packets
- qca8k: support link aggregation and port mirroring
- Qualcomm 802.11ax WiFi (ath11k):
- qca6390, wcn6855: enable 802.11 power save mode in station mode
- BSS color change support
- WCN6855 hw2.1 support
- 11d scan offload support
- scan MAC address randomization support
- full monitor mode, only supported on QCN9074
- qca6390/wcn6855: report signal and tx bitrate
- qca6390: rfkill support
- qca6390/wcn6855: regdb.bin support
- Intel WiFi (iwlwifi):
- support SAR GEO Offset Mapping (SGOM) and Time-Aware-SAR (TAS)
in cooperation with the BIOS
- support for Optimized Connectivity Experience (OCE) scan
- support firmware API version 68
- lots of preparatory work for the upcoming Bz device family
- MediaTek WiFi (mt76):
- Specific Absorption Rate (SAR) support
- mt7921: 160 MHz channel support
- RealTek WiFi (rtw88):
- Specific Absorption Rate (SAR) support
- scan offload
- Other WiFi NICs
- ath10k: support fetching (pre-)calibration data from nvmem
- brcmfmac: configure keep-alive packet on suspend
- wcn36xx: beacon filter support
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=KLm3
-----END PGP SIGNATURE-----
Merge tag '5.17-net-next' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core
----
- Defer freeing TCP skbs to the BH handler, whenever possible, or at
least perform the freeing outside of the socket lock section to
decrease cross-CPU allocator work and improve latency.
- Add netdevice refcount tracking to locate sources of netdevice and
net namespace refcount leaks.
- Make Tx watchdog less intrusive - avoid pausing Tx and restarting
all queues from a single CPU removing latency spikes.
- Various small optimizations throughout the stack from Eric Dumazet.
- Make netdev->dev_addr[] constant, force modifications to go via
appropriate helpers to allow us to keep addresses in ordered data
structures.
- Replace unix_table_lock with per-hash locks, improving performance
of bind() calls.
- Extend skb drop tracepoint with a drop reason.
- Allow SO_MARK and SO_PRIORITY setsockopt under CAP_NET_RAW.
BPF
---
- New helpers:
- bpf_find_vma(), find and inspect VMAs for profiling use cases
- bpf_loop(), runtime-bounded loop helper trading some execution
time for much faster (if at all converging) verification
- bpf_strncmp(), improve performance, avoid compiler flakiness
- bpf_get_func_arg(), bpf_get_func_ret(), bpf_get_func_arg_cnt()
for tracing programs, all inlined by the verifier
- Support BPF relocations (CO-RE) in the kernel loader.
- Further the support for BTF_TYPE_TAG annotations.
- Allow access to local storage in sleepable helpers.
- Convert verifier argument types to a composable form with different
attributes which can be shared across types (ro, maybe-null).
- Prepare libbpf for upcoming v1.0 release by cleaning up APIs,
creating new, extensible ones where missing and deprecating those
to be removed.
Protocols
---------
- WiFi (mac80211/cfg80211):
- notify user space about long "come back in N" AP responses,
allow it to react to such temporary rejections
- allow non-standard VHT MCS 10/11 rates
- use coarse time in airtime fairness code to save CPU cycles
- Bluetooth:
- rework of HCI command execution serialization to use a common
queue and work struct, and improve handling errors reported in
the middle of a batch of commands
- rework HCI event handling to use skb_pull_data, avoiding packet
parsing pitfalls
- support AOSP Bluetooth Quality Report
- SMC:
- support net namespaces, following the RDMA model
- improve connection establishment latency by pre-clearing buffers
- introduce TCP ULP for automatic redirection to SMC
- Multi-Path TCP:
- support ioctls: SIOCINQ, OUTQ, and OUTQNSD
- support socket options: IP_TOS, IP_FREEBIND, IP_TRANSPARENT,
IPV6_FREEBIND, and IPV6_TRANSPARENT, TCP_CORK and TCP_NODELAY
- support cmsgs: TCP_INQ
- improvements in the data scheduler (assigning data to subflows)
- support fastclose option (quick shutdown of the full MPTCP
connection, similar to TCP RST in regular TCP)
- MCTP (Management Component Transport) over serial, as defined by
DMTF spec DSP0253 - "MCTP Serial Transport Binding".
Driver API
----------
- Support timestamping on bond interfaces in active/passive mode.
- Introduce generic phylink link mode validation for drivers which
don't have any quirks and where MAC capability bits fully express
what's supported. Allow PCS layer to participate in the validation.
Convert a number of drivers.
- Add support to set/get size of buffers on the Rx rings and size of
the tx copybreak buffer via ethtool.
- Support offloading TC actions as first-class citizens rather than
only as attributes of filters, improve sharing and device resource
utilization.
- WiFi (mac80211/cfg80211):
- support forwarding offload (ndo_fill_forward_path)
- support for background radar detection hardware
- SA Query Procedures offload on the AP side
New hardware / drivers
----------------------
- tsnep - FPGA based TSN endpoint Ethernet MAC used in PLCs with
real-time requirements for isochronous communication with protocols
like OPC UA Pub/Sub.
- Qualcomm BAM-DMUX WWAN - driver for data channels of modems
integrated into many older Qualcomm SoCs, e.g. MSM8916 or MSM8974
(qcom_bam_dmux).
- Microchip LAN966x multi-port Gigabit AVB/TSN Ethernet Switch driver
with support for bridging, VLANs and multicast forwarding
(lan966x).
- iwlmei driver for co-operating between Intel's WiFi driver and
Intel's Active Management Technology (AMT) devices.
- mse102x - Vertexcom MSE102x Homeplug GreenPHY chips
- Bluetooth:
- MediaTek MT7921 SDIO devices
- Foxconn MT7922A
- Realtek RTL8852AE
Drivers
-------
- Significantly improve performance in the datapaths of: lan78xx,
ax88179_178a, lantiq_xrx200, bnxt.
- Intel Ethernet NICs:
- igb: support PTP/time PEROUT and EXTTS SDP functions on
82580/i354/i350 adapters
- ixgbevf: new PF -> VF mailbox API which avoids the risk of
mailbox corruption with ESXi
- iavf: support configuration of VLAN features of finer
granularity, stacked tags and filtering
- ice: PTP support for new E822 devices with sub-ns precision
- ice: support firmware activation without reboot
- Mellanox Ethernet NICs (mlx5):
- expose control over IRQ coalescing mode (CQE vs EQE) via ethtool
- support TC forwarding when tunnel encap and decap happen between
two ports of the same NIC
- dynamically size and allow disabling various features to save
resources for running in embedded / SmartNIC scenarios
- Broadcom Ethernet NICs (bnxt):
- use page frag allocator to improve Rx performance
- expose control over IRQ coalescing mode (CQE vs EQE) via ethtool
- Other Ethernet NICs:
- amd-xgbe: add Ryzen 6000 (Yellow Carp) Ethernet support
- Microsoft cloud/virtual NIC (mana):
- add XDP support (PASS, DROP, TX)
- Mellanox Ethernet switches (mlxsw):
- initial support for Spectrum-4 ASICs
- VxLAN with IPv6 underlay
- Marvell Ethernet switches (prestera):
- support flower flow templates
- add basic IP forwarding support
- NXP embedded Ethernet switches (ocelot & felix):
- support Per-Stream Filtering and Policing (PSFP)
- enable cut-through forwarding between ports by default
- support FDMA to improve packet Rx/Tx to CPU
- Other embedded switches:
- hellcreek: improve trapping management (STP and PTP) packets
- qca8k: support link aggregation and port mirroring
- Qualcomm 802.11ax WiFi (ath11k):
- qca6390, wcn6855: enable 802.11 power save mode in station mode
- BSS color change support
- WCN6855 hw2.1 support
- 11d scan offload support
- scan MAC address randomization support
- full monitor mode, only supported on QCN9074
- qca6390/wcn6855: report signal and tx bitrate
- qca6390: rfkill support
- qca6390/wcn6855: regdb.bin support
- Intel WiFi (iwlwifi):
- support SAR GEO Offset Mapping (SGOM) and Time-Aware-SAR (TAS)
in cooperation with the BIOS
- support for Optimized Connectivity Experience (OCE) scan
- support firmware API version 68
- lots of preparatory work for the upcoming Bz device family
- MediaTek WiFi (mt76):
- Specific Absorption Rate (SAR) support
- mt7921: 160 MHz channel support
- RealTek WiFi (rtw88):
- Specific Absorption Rate (SAR) support
- scan offload
- Other WiFi NICs
- ath10k: support fetching (pre-)calibration data from nvmem
- brcmfmac: configure keep-alive packet on suspend
- wcn36xx: beacon filter support"
* tag '5.17-net-next' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2048 commits)
tcp: tcp_send_challenge_ack delete useless param `skb`
net/qla3xxx: Remove useless DMA-32 fallback configuration
rocker: Remove useless DMA-32 fallback configuration
hinic: Remove useless DMA-32 fallback configuration
lan743x: Remove useless DMA-32 fallback configuration
net: enetc: Remove useless DMA-32 fallback configuration
cxgb4vf: Remove useless DMA-32 fallback configuration
cxgb4: Remove useless DMA-32 fallback configuration
cxgb3: Remove useless DMA-32 fallback configuration
bnx2x: Remove useless DMA-32 fallback configuration
et131x: Remove useless DMA-32 fallback configuration
be2net: Remove useless DMA-32 fallback configuration
vmxnet3: Remove useless DMA-32 fallback configuration
bna: Simplify DMA setting
net: alteon: Simplify DMA setting
myri10ge: Simplify DMA setting
qlcnic: Simplify DMA setting
net: allwinner: Fix print format
page_pool: remove spinlock in page_pool_refill_alloc_cache()
amt: fix wrong return type of amt_send_membership_update()
...
There are cleanups and minor bugfixes across several SoC specific
drivers, for Qualcomm, Samsung, NXP i.MX, AT91, Tegra, Keystone,
Renesas, ZynqMP
Noteworthy new features are:
- The op-tee firmware driver gains support for asynchronous
notifications from secure-world firmware.
- Qualcomm platforms gain support for new SoC types in various
drivers: power domain, cache controller, RPM sleep, soc-info
- Samsung SoC drivers gain support for new SoCs in ChipID and PMU,
as well as a new USIv2 driver that handles various types of
serial communiction (uart, i2c, spi)
- Renesas adds support for R-Car S4-8 (R8A779F0) in multiple
drivers, as well as memory controller support for RZ/G2L
(R9A07G044).
- Apple M1 gains support for the PMGR power management driver
-----BEGIN PGP SIGNATURE-----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=tlZT
-----END PGP SIGNATURE-----
Merge tag 'drivers-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"There are cleanups and minor bugfixes across several SoC specific
drivers, for Qualcomm, Samsung, NXP i.MX, AT91, Tegra, Keystone,
Renesas, ZynqMP
Noteworthy new features are:
- The op-tee firmware driver gains support for asynchronous
notifications from secure-world firmware.
- Qualcomm platforms gain support for new SoC types in various
drivers: power domain, cache controller, RPM sleep, soc-info
- Samsung SoC drivers gain support for new SoCs in ChipID and PMU, as
well as a new USIv2 driver that handles various types of serial
communiction (uart, i2c, spi)
- Renesas adds support for R-Car S4-8 (R8A779F0) in multiple drivers,
as well as memory controller support for RZ/G2L (R9A07G044).
- Apple M1 gains support for the PMGR power management driver"
* tag 'drivers-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (94 commits)
soc: qcom: rpmh-rsc: Fix typo in a comment
soc: qcom: socinfo: Add SM6350 and SM7225
dt-bindings: arm: msm: Don't mark LLCC interrupt as required
dt-bindings: firmware: scm: Add SM6350 compatible
dt-bindings: arm: msm: Add LLCC for SM6350
soc: qcom: rpmhpd: Sort power-domain definitions and lists
soc: qcom: rpmhpd: Remove mx/cx relationship on sc7280
soc: qcom: rpmhpd: Rename rpmhpd struct names
soc: qcom: rpmhpd: sm8450: Add the missing .peer for sm8450_cx_ao
soc: qcom: socinfo: add SM8450 ID
soc: qcom: rpmhpd: Add SM8450 power domains
dt-bindings: power: rpmpd: Add SM8450 to rpmpd binding
soc: qcom: smem: Update max processor count
dt-bindings: arm: qcom: Document SM8450 SoC and boards
dt-bindings: firmware: scm: Add SM8450 compatible
dt-bindings: arm: cpus: Add kryo780 compatible
soc: qcom: rpmpd: Add support for sm6125
dt-bindings: qcom-rpmpd: Add sm6125 power domains
soc: qcom: aoss: constify static struct thermal_cooling_device_ops
PM: AVS: qcom-cpr: Use div64_ul instead of do_div
...
Add support for flushing the MAC table on a given port in the ocelot
switch library, and use this functionality in the felix DSA driver.
This operation is needed when a port leaves a bridge to become
standalone, and when the learning is disabled, and when the STP state
changes to a state where no FDB entry should be present.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220107144229.244584-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Only couple drivers need to get the -ENODEV error code and majority of
drivers need to explicitly initialize the performance state. Add new
common helper which sets up OPP table for these drivers.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Ethernet frames can be extracted or injected autonomously to or from
the device’s DDR3/DDR3L memory and/or PCIe memory space. Linked list
data structures in memory are used for injecting or extracting Ethernet
frames. The FDMA generates interrupts when frame extraction or
injection is done and when the linked lists need updating.
The FDMA is shared between all the ethernet ports of the switch and
uses a linked list of descriptors (DCB) to inject and extract packets.
Before adding descriptors, the FDMA channels must be stopped. It would
be inefficient to do that each time a descriptor would be added so the
channels are restarted only once they stopped.
Both channels uses ring-like structure to feed the DCBs to the FDMA.
head and tail are never touched by hardware and are completely handled
by the driver. On top of that, page recycling has been added and is
mostly taken from gianfar driver.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Co-developed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to support PTP in FDMA, PTP handling code is needed. Since
this is the same as for register-based extraction, export it with
a new ocelot_ptp_rx_timestamp() function.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
FDMA will need this code to prepare the injection frame header when
sending SKBs. Move this code into ocelot_ifh_port_set() and add
conditional IFH setting for vlan and rew op if they are not set.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
commit 32ecd22ba6 ("net: mscc: ocelot: split register definitions to a
separate file") left out an include for <soc/mscc/ocelot_vcap.h>. It was
missed because the only consumer was ocelot_vsc7514.h, which already
included ocelot_vcap.
Fixes: 32ecd22ba6 ("net: mscc: ocelot: split register definitions to a separate file")
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211209074010.1813010-1-colin.foster@in-advantage.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move these to a separate file will allow them to be shared to other
drivers.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
VCAP (Versatile Content Aware Processor) is the TCAM-based engine behind
tc flower offload on ocelot, among other things. The ingress port mask
on which VCAP rules match is present as a bit field in the actual key of
the rule. This means that it is possible for a rule to be shared among
multiple source ports. When the rule is added one by one on each desired
port, that the ingress port mask of the key must be edited and rewritten
to hardware.
But the API in ocelot_vcap.c does not allow for this. For one thing,
ocelot_vcap_filter_add() and ocelot_vcap_filter_del() are not symmetric,
because ocelot_vcap_filter_add() works with a preallocated and
prepopulated filter and programs it to hardware, and
ocelot_vcap_filter_del() does both the job of removing the specified
filter from hardware, as well as kfreeing it. That is to say, the only
option of editing a filter in place, which is to delete it, modify the
structure and add it back, does not work because it results in
use-after-free.
This patch introduces ocelot_vcap_filter_replace, which trivially
reprograms a VCAP entry to hardware, at the exact same index at which it
existed before, without modifying any list or allocating any memory.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The VSC9959 switch embedded within NXP LS1028A (and that version of
Ocelot switches only) supports cut-through forwarding - meaning it can
start the process of looking up the destination ports for a packet, and
forward towards those ports, before the entire packet has been received
(as opposed to the store-and-forward mode).
The up side is having lower forwarding latency for large packets. The
down side is that frames with FCS errors are forwarded instead of being
dropped. However, erroneous frames do not result in incorrect updates of
the FDB or incorrect policer updates, since these processes are deferred
inside the switch to the end of frame. Since the switch starts the
cut-through forwarding process after all packet headers (including IP,
if any) have been processed, packets with large headers and small
payload do not see the benefit of lower forwarding latency.
There are two cases that need special attention.
The first is when a packet is multicast (or flooded) to multiple
destinations, one of which doesn't have cut-through forwarding enabled.
The switch deals with this automatically by disabling cut-through
forwarding for the frame towards all destination ports.
The second is when a packet is forwarded from a port of lower link speed
towards a port of higher link speed. This is not handled by the hardware
and needs software intervention.
Since we practically need to update the cut-through forwarding domain
from paths that aren't serialized by the rtnl_mutex (phylink
mac_link_down/mac_link_up ops), this means we need to serialize physical
link events with user space updates of bonding/bridging domains.
Enabling cut-through forwarding is done per {egress port, traffic class}.
I don't see any reason why this would be a configurable option as long
as it works without issues, and there doesn't appear to be any user
space configuration tool to toggle this on/off, so this patch enables
cut-through forwarding on all eligible ports and traffic classes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20211125125808.2383984-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
PSFP rules take effect on the streams from any port of VSC9959 switch.
This patch use ingress port to limit the rule only active on this port.
Each stream can only match two ingress source ports in VSC9959. Streams
from lowest port gets the configuration of SFID pointed by MAC Table
lookup and streams from highest port gets the configuration of (SFID+1)
pointed by MAC Table lookup. This patch defines the PSFP rule on highest
port as dummy rule, which means that it does not modify the MAC table.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Policer was previously automatically assigned from the highest index to
the lowest index from policer pool. But police action of tc flower now
uses index to set an police entry. This patch uses the police index to
set vcap policers, so that one policer can be shared by multiple rules.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VSC9959 supports Per-Stream Filtering and Policing(PSFP) that complies
with the IEEE 802.1Qci standard. The stream is identified by Null stream
identification(DMAC and VLAN ID) defined in IEEE802.1CB.
For PSFP, four tables need to be set up: stream table, stream filter
table, stream gate table, and flow meter table. Identify the stream by
parsing the tc flower keys and add it to the stream table. The stream
filter table is automatically maintained, and its index is determined by
SGID(flow gate index) and FMID(flow meter index).
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PSFP support gate and police action. This patch add the gate and police
action to flower parse action, check chain ID to determine which block
to offload. Adding psfp callback functions to add, delete and update gate
and police in PSFP table if hardware supports it.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ocelot_mact_learn_streamdata() can be used in VSC9959 to overwrite an
FDB entry with stream data. The stream data includes SFID and SSID which
can be used for PSFP and FRER set.
ocelot_mact_lookup() can be used to check if the given {DMAC, VID} FDB
entry is exist, and also can retrieve the DEST_IDX and entry type for
the FDB entry.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are all the driver updates for SoC specific drivers. There
are a couple of subsystems with individual maintainers picking up
their patches here:
- The reset controller subsystem add support for a few new SoC
variants to existing drivers, along with other minor improvements
- The OP-TEE subsystem gets a driver for the ARM FF-A transport
- The memory controller subsystem has improvements for Tegra,
Mediatek, Renesas, Freescale and Broadcom specific drivers.
- The tegra cpuidle driver changes get merged through this
tree this time. There are only minor changes, but they depend
on other tegra driver updates here.
- The ep93xx platform finally moves to using the drivers/clk/
subsystem, moving the code out of arch/arm in the process.
This depends on a small sound driver change that is included
here as well.
- There are some minor updates for Qualcomm and Tegra specific
firmware drivers.
The other driver updates are mainly for drivers/soc, which contains
a mixture of vendor specific drivers that don't really fit elsewhere:
- Mediatek drivers gain more support for MT8192, with new support for
hw-mutex and mmsys routing, plus support for reset lines in the
mmsys driver.
- Qualcomm gains a new "sleep stats" driver, and support for
the "Generic Packet Router" in the APR driver.
- There is a new user interface for routing the UARTS on ASpeed
BMCs, something that apparently nobody else has needed so far.
- More drivers can now be built as loadable modules, in particular
for Broadcom and Samsung platforms.
- Lots of improvements to the TI sysc driver for better suspend/resume
support
Finally, there are lots of minor cleanups and new device IDs for
amlogic, renesas, tegra, qualcomm, mediateka, samsung, imx, layerscape,
allwinner, broadcom, and omap.
-----BEGIN PGP SIGNATURE-----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=tUuj
-----END PGP SIGNATURE-----
Merge tag 'drivers-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are all the driver updates for SoC specific drivers. There are a
couple of subsystems with individual maintainers picking up their
patches here:
- The reset controller subsystem add support for a few new SoC
variants to existing drivers, along with other minor improvements
- The OP-TEE subsystem gets a driver for the ARM FF-A transport
- The memory controller subsystem has improvements for Tegra,
Mediatek, Renesas, Freescale and Broadcom specific drivers.
- The tegra cpuidle driver changes get merged through this tree this
time. There are only minor changes, but they depend on other tegra
driver updates here.
- The ep93xx platform finally moves to using the drivers/clk/
subsystem, moving the code out of arch/arm in the process. This
depends on a small sound driver change that is included here as
well.
- There are some minor updates for Qualcomm and Tegra specific
firmware drivers.
The other driver updates are mainly for drivers/soc, which contains a
mixture of vendor specific drivers that don't really fit elsewhere:
- Mediatek drivers gain more support for MT8192, with new support for
hw-mutex and mmsys routing, plus support for reset lines in the
mmsys driver.
- Qualcomm gains a new "sleep stats" driver, and support for the
"Generic Packet Router" in the APR driver.
- There is a new user interface for routing the UARTS on ASpeed BMCs,
something that apparently nobody else has needed so far.
- More drivers can now be built as loadable modules, in particular
for Broadcom and Samsung platforms.
- Lots of improvements to the TI sysc driver for better
suspend/resume support"
Finally, there are lots of minor cleanups and new device IDs for
amlogic, renesas, tegra, qualcomm, mediateka, samsung, imx,
layerscape, allwinner, broadcom, and omap"
* tag 'drivers-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (179 commits)
optee: Fix spelling mistake "reclain" -> "reclaim"
Revert "firmware: qcom: scm: Add support for MC boot address API"
qcom: spm: allow compile-testing
firmware: arm_ffa: Remove unused 'compat_version' variable
soc: samsung: exynos-chipid: add exynosautov9 SoC support
firmware: qcom: scm: Don't break compile test on non-ARM platforms
soc: qcom: smp2p: Add of_node_put() before goto
soc: qcom: apr: Add of_node_put() before return
soc: qcom: qcom_stats: Fix client votes offset
soc: qcom: rpmhpd: fix sm8350_mxc's peer domain
dt-bindings: arm: cpus: Document qcom,msm8916-smp enable-method
ARM: qcom: Add qcom,msm8916-smp enable-method identical to MSM8226
firmware: qcom: scm: Add support for MC boot address API
soc: qcom: spm: Add 8916 SPM register data
dt-bindings: soc: qcom: spm: Document qcom,msm8916-saw2-v3.0-cpu
soc: qcom: socinfo: Add PM8150C and SMB2351 models
firmware: qcom_scm: Fix error retval in __qcom_scm_is_call_available()
soc: aspeed: Add UART routing support
soc: fsl: dpio: rename the enqueue descriptor variable
soc: fsl: dpio: use an explicit NULL instead of 0
...
- Remove socket skb caches
- Add a SO_RESERVE_MEM socket op to forward allocate buffer space
and avoid memory accounting overhead on each message sent
- Introduce managed neighbor entries - added by control plane and
resolved by the kernel for use in acceleration paths (BPF / XDP
right now, HW offload users will benefit as well)
- Make neighbor eviction on link down controllable by userspace
to work around WiFi networks with bad roaming implementations
- vrf: Rework interaction with netfilter/conntrack
- fq_codel: implement L4S style ce_threshold_ect1 marking
- sch: Eliminate unnecessary RCU waits in mini_qdisc_pair_swap()
BPF:
- Add support for new btf kind BTF_KIND_TAG, arbitrary type tagging
as implemented in LLVM14
- Introduce bpf_get_branch_snapshot() to capture Last Branch Records
- Implement variadic trace_printk helper
- Add a new Bloomfilter map type
- Track <8-byte scalar spill and refill
- Access hw timestamp through BPF's __sk_buff
- Disallow unprivileged BPF by default
- Document BPF licensing
Netfilter:
- Introduce egress hook for looking at raw outgoing packets
- Allow matching on and modifying inner headers / payload data
- Add NFT_META_IFTYPE to match on the interface type either from
ingress or egress
Protocols:
- Multi-Path TCP:
- increase default max additional subflows to 2
- rework forward memory allocation
- add getsockopts: MPTCP_INFO, MPTCP_TCPINFO, MPTCP_SUBFLOW_ADDRS
- MCTP flow support allowing lower layer drivers to configure msg
muxing as needed
- Automatic Multicast Tunneling (AMT) driver based on RFC7450
- HSR support the redbox supervision frames (IEC-62439-3:2018)
- Support for the ip6ip6 encapsulation of IOAM
- Netlink interface for CAN-FD's Transmitter Delay Compensation
- Support SMC-Rv2 eliminating the current same-subnet restriction,
by exploiting the UDP encapsulation feature of RoCE adapters
- TLS: add SM4 GCM/CCM crypto support
- Bluetooth: initial support for link quality and audio/codec
offload
Driver APIs:
- Add a batched interface for RX buffer allocation in AF_XDP
buffer pool
- ethtool: Add ability to control transceiver modules' power mode
- phy: Introduce supported interfaces bitmap to express MAC
capabilities and simplify PHY code
- Drop rtnl_lock from DSA .port_fdb_{add,del} callbacks
New drivers:
- WiFi driver for Realtek 8852AE 802.11ax devices (rtw89)
- Ethernet driver for ASIX AX88796C SPI device (x88796c)
Drivers:
- Broadcom PHYs
- support 72165, 7712 16nm PHYs
- support IDDQ-SR for additional power savings
- PHY support for QCA8081, QCA9561 PHYs
- NXP DPAA2: support for IRQ coalescing
- NXP Ethernet (enetc): support for software TCP segmentation
- Renesas Ethernet (ravb) - support DMAC and EMAC blocks of
Gigabit-capable IP found on RZ/G2L SoC
- Intel 100G Ethernet
- support for eswitch offload of TC/OvS flow API, including
offload of GRE, VxLAN, Geneve tunneling
- support application device queues - ability to assign Rx and Tx
queues to application threads
- PTP and PPS (pulse-per-second) extensions
- Broadcom Ethernet (bnxt)
- devlink health reporting and device reload extensions
- Mellanox Ethernet (mlx5)
- offload macvlan interfaces
- support HW offload of TC rules involving OVS internal ports
- support HW-GRO and header/data split
- support application device queues
- Marvell OcteonTx2:
- add XDP support for PF
- add PTP support for VF
- Qualcomm Ethernet switch (qca8k): support for QCA8328
- Realtek Ethernet DSA switch (rtl8366rb)
- support bridge offload
- support STP, fast aging, disabling address learning
- support for Realtek RTL8365MB-VC, a 4+1 port 10M/100M/1GE switch
- Mellanox Ethernet/IB switch (mlxsw)
- multi-level qdisc hierarchy offload (e.g. RED, prio and shaping)
- offload root TBF qdisc as port shaper
- support multiple routing interface MAC address prefixes
- support for IP-in-IP with IPv6 underlay
- MediaTek WiFi (mt76)
- mt7921 - ASPM, 6GHz, SDIO and testmode support
- mt7915 - LED and TWT support
- Qualcomm WiFi (ath11k)
- include channel rx and tx time in survey dump statistics
- support for 80P80 and 160 MHz bandwidths
- support channel 2 in 6 GHz band
- spectral scan support for QCN9074
- support for rx decapsulation offload (data frames in 802.3
format)
- Qualcomm phone SoC WiFi (wcn36xx)
- enable Idle Mode Power Save (IMPS) to reduce power consumption
during idle
- Bluetooth driver support for MediaTek MT7922 and MT7921
- Enable support for AOSP Bluetooth extension in Qualcomm WCN399x
and Realtek 8822C/8852A
- Microsoft vNIC driver (mana)
- support hibernation and kexec
- Google vNIC driver (gve)
- support for jumbo frames
- implement Rx page reuse
Refactor:
- Make all writes to netdev->dev_addr go thru helpers, so that we
can add this address to the address rbtree and handle the updates
- Various TCP cleanups and optimizations including improvements
to CPU cache use
- Simplify the gnet_stats, Qdisc stats' handling and remove
qdisc->running sequence counter
- Driver changes and API updates to address devlink locking
deficiencies
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=srde
-----END PGP SIGNATURE-----
Merge tag 'net-next-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- Remove socket skb caches
- Add a SO_RESERVE_MEM socket op to forward allocate buffer space and
avoid memory accounting overhead on each message sent
- Introduce managed neighbor entries - added by control plane and
resolved by the kernel for use in acceleration paths (BPF / XDP
right now, HW offload users will benefit as well)
- Make neighbor eviction on link down controllable by userspace to
work around WiFi networks with bad roaming implementations
- vrf: Rework interaction with netfilter/conntrack
- fq_codel: implement L4S style ce_threshold_ect1 marking
- sch: Eliminate unnecessary RCU waits in mini_qdisc_pair_swap()
BPF:
- Add support for new btf kind BTF_KIND_TAG, arbitrary type tagging
as implemented in LLVM14
- Introduce bpf_get_branch_snapshot() to capture Last Branch Records
- Implement variadic trace_printk helper
- Add a new Bloomfilter map type
- Track <8-byte scalar spill and refill
- Access hw timestamp through BPF's __sk_buff
- Disallow unprivileged BPF by default
- Document BPF licensing
Netfilter:
- Introduce egress hook for looking at raw outgoing packets
- Allow matching on and modifying inner headers / payload data
- Add NFT_META_IFTYPE to match on the interface type either from
ingress or egress
Protocols:
- Multi-Path TCP:
- increase default max additional subflows to 2
- rework forward memory allocation
- add getsockopts: MPTCP_INFO, MPTCP_TCPINFO, MPTCP_SUBFLOW_ADDRS
- MCTP flow support allowing lower layer drivers to configure msg
muxing as needed
- Automatic Multicast Tunneling (AMT) driver based on RFC7450
- HSR support the redbox supervision frames (IEC-62439-3:2018)
- Support for the ip6ip6 encapsulation of IOAM
- Netlink interface for CAN-FD's Transmitter Delay Compensation
- Support SMC-Rv2 eliminating the current same-subnet restriction, by
exploiting the UDP encapsulation feature of RoCE adapters
- TLS: add SM4 GCM/CCM crypto support
- Bluetooth: initial support for link quality and audio/codec offload
Driver APIs:
- Add a batched interface for RX buffer allocation in AF_XDP buffer
pool
- ethtool: Add ability to control transceiver modules' power mode
- phy: Introduce supported interfaces bitmap to express MAC
capabilities and simplify PHY code
- Drop rtnl_lock from DSA .port_fdb_{add,del} callbacks
New drivers:
- WiFi driver for Realtek 8852AE 802.11ax devices (rtw89)
- Ethernet driver for ASIX AX88796C SPI device (x88796c)
Drivers:
- Broadcom PHYs
- support 72165, 7712 16nm PHYs
- support IDDQ-SR for additional power savings
- PHY support for QCA8081, QCA9561 PHYs
- NXP DPAA2: support for IRQ coalescing
- NXP Ethernet (enetc): support for software TCP segmentation
- Renesas Ethernet (ravb) - support DMAC and EMAC blocks of
Gigabit-capable IP found on RZ/G2L SoC
- Intel 100G Ethernet
- support for eswitch offload of TC/OvS flow API, including
offload of GRE, VxLAN, Geneve tunneling
- support application device queues - ability to assign Rx and Tx
queues to application threads
- PTP and PPS (pulse-per-second) extensions
- Broadcom Ethernet (bnxt)
- devlink health reporting and device reload extensions
- Mellanox Ethernet (mlx5)
- offload macvlan interfaces
- support HW offload of TC rules involving OVS internal ports
- support HW-GRO and header/data split
- support application device queues
- Marvell OcteonTx2:
- add XDP support for PF
- add PTP support for VF
- Qualcomm Ethernet switch (qca8k): support for QCA8328
- Realtek Ethernet DSA switch (rtl8366rb)
- support bridge offload
- support STP, fast aging, disabling address learning
- support for Realtek RTL8365MB-VC, a 4+1 port 10M/100M/1GE switch
- Mellanox Ethernet/IB switch (mlxsw)
- multi-level qdisc hierarchy offload (e.g. RED, prio and shaping)
- offload root TBF qdisc as port shaper
- support multiple routing interface MAC address prefixes
- support for IP-in-IP with IPv6 underlay
- MediaTek WiFi (mt76)
- mt7921 - ASPM, 6GHz, SDIO and testmode support
- mt7915 - LED and TWT support
- Qualcomm WiFi (ath11k)
- include channel rx and tx time in survey dump statistics
- support for 80P80 and 160 MHz bandwidths
- support channel 2 in 6 GHz band
- spectral scan support for QCN9074
- support for rx decapsulation offload (data frames in 802.3
format)
- Qualcomm phone SoC WiFi (wcn36xx)
- enable Idle Mode Power Save (IMPS) to reduce power consumption
during idle
- Bluetooth driver support for MediaTek MT7922 and MT7921
- Enable support for AOSP Bluetooth extension in Qualcomm WCN399x and
Realtek 8822C/8852A
- Microsoft vNIC driver (mana)
- support hibernation and kexec
- Google vNIC driver (gve)
- support for jumbo frames
- implement Rx page reuse
Refactor:
- Make all writes to netdev->dev_addr go thru helpers, so that we can
add this address to the address rbtree and handle the updates
- Various TCP cleanups and optimizations including improvements to
CPU cache use
- Simplify the gnet_stats, Qdisc stats' handling and remove
qdisc->running sequence counter
- Driver changes and API updates to address devlink locking
deficiencies"
* tag 'net-next-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2122 commits)
Revert "net: avoid double accounting for pure zerocopy skbs"
selftests: net: add arp_ndisc_evict_nocarrier
net: ndisc: introduce ndisc_evict_nocarrier sysctl parameter
net: arp: introduce arp_evict_nocarrier sysctl parameter
libbpf: Deprecate AF_XDP support
kbuild: Unify options for BTF generation for vmlinux and modules
selftests/bpf: Add a testcase for 64-bit bounds propagation issue.
bpf: Fix propagation of signed bounds from 64-bit min/max into 32-bit.
bpf: Fix propagation of bounds from 64-bit min/max into 32-bit and var_off.
net: vmxnet3: remove multiple false checks in vmxnet3_ethtool.c
net: avoid double accounting for pure zerocopy skbs
tcp: rename sk_wmem_free_skb
netdevsim: fix uninit value in nsim_drv_configure_vfs()
selftests/bpf: Fix also no-alu32 strobemeta selftest
bpf: Add missing map_delete_elem method to bloom filter map
selftests/bpf: Add bloom map success test for userspace calls
bpf: Add alignment padding for "map_extra" + consolidate holes
bpf: Bloom filter map naming fixups
selftests/bpf: Add test cases for struct_ops prog
bpf: Add dummy BPF STRUCT_OPS for test purpose
...
- No core updates
- No new clocksource/event driver
- A large rework of the ARM architected timer driver to prepare for the
support of the upcoming ARMv8.6 support
- Fix Kconfig options for Exynos MCT, Samsung PWM and TI DM timers
- Address a namespace collison in the ARC sp804 timer driver
-----BEGIN PGP SIGNATURE-----
iQJHBAABCgAxFiEEQp8+kY+LLUocC4bMphj1TA10mKEFAmF/IPsTHHRnbHhAbGlu
dXRyb25peC5kZQAKCRCmGPVMDXSYoXztEACE15PRW/s3dsKjsX4HgZocPS3WSeBx
Nim90LHLWA8hiN3LdY5PmyB5lWHFPojCNtnnnA3hAAasalxtxu00XUwMx11Ewf7C
HDpYvW4Pp3QHFH9i45nxVJ/2bhiL7g8cpvYNrXuk2rVkZnBf13LGqD4IUJbts/gY
X+T0NTDHFNjJjbabuD4LVsfKkerPPJawYtL6EnFn8hkZwMKVY2Mq0xw6fCzA7qGy
JbBkt0Or5k7imruq3uob9V+IscmkcPRxrP1JOgJLbzCbax+bpz2SL1nZxm5NAeol
Hdxx+bP2PnpoCsq6GnN3q17nvr8PEOeEQ02AcZ/5IpExIfBnIDahJ61KA8Ao6WGm
xvVY4fIG6nqul6LMqoAyVc0BeG4Mc7u3D12f+1/UE9pmYbMEM5TcHRbxg0QgTauF
R78xc5P5v+B2LcUTE9/czJlaCZQuAF+4N60Lnt+aW0Ahsa0h+O2vrX1rBOC3d4US
12xexkAimMS8VvmuD5wSPE9JrBMDZraJuDM3G+5cwOjXIG8VFXOSloOn/9BhWFEM
c0scefsGFxENDwkd3d6PmGfrtxSOnqAzhvxgRyJ9zql9wX6LDOa6s2HXKxdSXEL8
N18WTWsC0Ps60XLlH9CQrBj/T0YnKpOazMx0LIFLPFqEkoSkEjq1j3KgDnSQQ4uE
J4c2UU4M8FnMlg==
=SVx3
-----END PGP SIGNATURE-----
Merge tag 'timers-core-2021-10-31' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"Time, timers and timekeeping updates:
- No core updates
- No new clocksource/event driver
- A large rework of the ARM architected timer driver to prepare for
the support of the upcoming ARMv8.6 support
- Fix Kconfig options for Exynos MCT, Samsung PWM and TI DM timers
- Address a namespace collison in the ARC sp804 timer driver"
* tag 'timers-core-2021-10-31' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/timer-ti-dm: Select TIMER_OF
clocksource/drivers/exynosy: Depend on sub-architecture for Exynos MCT and Samsung PWM
clocksource/drivers/arch_arm_timer: Move workaround synchronisation around
clocksource/drivers/arm_arch_timer: Fix masking for high freq counters
clocksource/drivers/arm_arch_timer: Drop unnecessary ISB on CVAL programming
clocksource/drivers/arm_arch_timer: Remove any trace of the TVAL programming interface
clocksource/drivers/arm_arch_timer: Work around broken CVAL implementations
clocksource/drivers/arm_arch_timer: Advertise 56bit timer to the core code
clocksource/drivers/arm_arch_timer: Move MMIO timer programming over to CVAL
clocksource/drivers/arm_arch_timer: Fix MMIO base address vs callback ordering issue
clocksource/drivers/arm_arch_timer: Move drop _tval from erratum function names
clocksource/drivers/arm_arch_timer: Move system register timer programming over to CVAL
clocksource/drivers/arm_arch_timer: Extend write side of timer register accessors to u64
clocksource/drivers/arm_arch_timer: Drop CNT*_TVAL read accessors
clocksource/arm_arch_timer: Add build-time guards for unhandled register accesses
clocksource/drivers/arc_timer: Eliminate redefined macro error
DSA would like to remove the rtnl_lock from its
SWITCHDEV_FDB_{ADD,DEL}_TO_DEVICE handlers, and the felix driver uses
the same MAC table functions as ocelot.
This means that the MAC table functions will no longer be implicitly
serialized with respect to each other by the rtnl_mutex, we need to add
a dedicated lock in ocelot for the non-atomic operations of selecting a
MAC table row, reading/writing what we want and polling for completion.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA would like to remove the rtnl_lock from its
SWITCHDEV_FDB_{ADD,DEL}_TO_DEVICE handlers, and the felix driver uses
the same MAC table functions as ocelot.
This means that the MAC table functions will no longer be implicitly
serialized with respect to each other by the rtnl_mutex, we need to add
a dedicated lock in ocelot for the non-atomic operations of selecting a
MAC table row, reading/writing what we want and polling for completion.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have a list of struct ocelot_bridge_vlan entries, we can
rewrite the pvid logic to simply point to one of those structures,
instead of having a separate structure with a "bool valid".
The NULL pointer will represent the lack of a bridge pvid (not to be
confused with the lack of a hardware pvid on the port, that is present
at all times).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At present, the ocelot driver accepts a single egress-untagged bridge
VLAN, meaning that this sequence of operations:
ip link add br0 type bridge vlan_filtering 1
ip link set swp0 master br0
bridge vlan add dev swp0 vid 2 pvid untagged
fails because the bridge automatically installs VID 1 as a pvid & untagged
VLAN, and vid 2 would be the second untagged VLAN on this port. It is
necessary to delete VID 1 before proceeding to add VID 2.
This limitation comes from the fact that we operate the port tag, when
it has an egress-untagged VID, in the OCELOT_PORT_TAG_NATIVE mode.
The ocelot switches do not have full flexibility and can either have one
single VID as egress-untagged, or all of them.
There are use cases for having all VLANs as egress-untagged as well, and
this patch adds support for that.
The change rewrites ocelot_port_set_native_vlan() into a more generic
ocelot_port_manage_port_tag() function. Because the software bridge's
state, transmitted to us via switchdev, can become very complex, we
don't attempt to track all possible state transitions, but instead take
a more declarative approach and just make ocelot_port_manage_port_tag()
figure out which more to operate in:
- port is VLAN-unaware: the classified VLAN (internal, unrelated to the
802.1Q header) is not inserted into packets on egress
- port is VLAN-aware:
- port has tagged VLANs:
-> port has no untagged VLAN: set up as pure trunk
-> port has one untagged VLAN: set up as trunk port + native VLAN
-> port has more than one untagged VLAN: this is an invalid config
which is rejected by ocelot_vlan_prepare
- port has no tagged VLANs
-> set up as pure egress-untagged port
We don't keep the number of tagged and untagged VLANs, we just count the
structures we keep.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First and foremost, the driver currently allocates a constant sized
4K * u32 (16KB memory) array for the VLAN masks. However, a typical
application might not need so many VLANs, so if we dynamically allocate
the memory as needed, we might actually save some space.
Secondly, we'll need to keep more advanced bookkeeping of the VLANs we
have, notably we'll have to check how many untagged and how many tagged
VLANs we have. This will have to stay in a structure, and allocating
another 16 KB array for that is again a bit too much.
So refactor the bridge VLANs in a linked list of structures.
The hook points inside the driver are ocelot_vlan_member_add() and
ocelot_vlan_member_del(), which previously used to operate on the
ocelot->vlan_mask[vid] array element.
ocelot_vlan_member_add() and ocelot_vlan_member_del() used to call
ocelot_vlan_member_set() to commit to the ocelot->vlan_mask.
Additionally, we had two calls to ocelot_vlan_member_set() from outside
those callers, and those were directly from ocelot_vlan_init().
Those calls do not set up bridging service VLANs, instead they:
- clear the VLAN table on reset
- set the port pvid to the value used by this driver for VLAN-unaware
standalone port operation (VID 0)
So now, when we have a structure which represents actual bridge VLANs,
VID 0 doesn't belong in that structure, since it is not part of the
bridging layer.
So delete the middle man, ocelot_vlan_member_set(), and let
ocelot_vlan_init() call directly ocelot_vlant_set_mask() which forgoes
any data structure and writes directly to hardware, which is all that we
need.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a cosmetic patch which clarifies what are the port tagging
options for Ocelot switches.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In drivers/clocksource/, 3 drivers use "TIMER_CTRL_IE" with 3 different
values. Two of them (mps2-timer.c and timer-sp804.c/timer-sp.h) are
localized and left unmodifed.
One of them uses a shared header file (<soc/arc/timers.h>), which is
what is causing the "redefined" warnings, so change the macro name in
that driver only. Also change the TIMER_CTRL_NH macro name.
Both macro names are prefixed with "ARC_" to reduce the likelihood
of future name collisions.
In file included from ../drivers/clocksource/timer-sp804.c:24:
../drivers/clocksource/timer-sp.h:25: error: "TIMER_CTRL_IE" redefined [-Werror]
25 | #define TIMER_CTRL_IE (1 << 5) /* VR */
../include/soc/arc/timers.h:20: note: this is the location of the previous definition
20 | #define TIMER_CTRL_IE (1 << 0) /* Interrupt when Count reaches limit */
Fixes: b26c2e3823 ("ARC: breakout timer include code into separate header")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Vineet Gupta <vgupta@kernel.org>
Cc: linux-snps-arc@lists.infradead.org
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Shahab Vahedi <Shahab.Vahedi@synopsys.com>
Acked-by: Vineet Gupta <vgupta@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210924020825.20317-1-rdunlap@infradead.org
Use the generic dynamic interrupt moderation (dim) framework to
implement adaptive interrupt coalescing on Rx. With the per-packet
interrupt scheme, a high interrupt rate has been noted for moderate
traffic flows leading to high CPU utilization.
The dpio driver exports new functions to enable/disable adaptive IRQ
coalescing on a DPIO object, to query the state or to update Net DIM
with a new set of bytes and frames dequeued.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In DPAA2 based SoCs, the IRQ coalesing support per software portal has 2
configurable parameters:
- the IRQ timeout period (QBMAN_CINH_SWP_ITPR): how many 256 QBMAN
cycles need to pass until a dequeue interrupt is asserted.
- the IRQ threshold (QBMAN_CINH_SWP_DQRR_ITR): how many dequeue
responses in the DQRR ring would generate an IRQ.
Add support for setting up and querying these IRQ coalescing related
parameters.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Through the dpio_get_attributes() firmware call the dpio driver has
access to the QBMAN clock frequency. Extend the structure which holds
the firmware's response so that we can have access to this information.
This will be needed in the next patches which also add support for
interrupt coalescing which needs to be configured based on the
frequency.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tools/testing/selftests/net/ioam6.sh
7b1700e009 ("selftests: net: modify IOAM tests for undef bits")
bf77b1400a ("selftests: net: Test for the IOAM encapsulation with IPv6")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This drops the use of power-domains for exposing the load_state from the
QMP driver to clients, to avoid issues related to system suspend.
SMP2P becomes wakeup capable, to allow dying remoteprocs to wake up
Linux from suspend to perform recovery.
It adds RPM power-domain support for SM6350 and MSM8953 and base RPM
support for MSM8953 and QCM2290.
It adds support for MSM8996, SDM630 and SDM660 in the SPM driver, which
will enable the introduction of proper voltage scaling of the CPU
subsystem.
Support for releasing secondary CPUs on MSM8226 is introduced.
The Asynchronous Packet Router (APR) driver is extended to support the
new Generic Packet Router (GPR) variant, which is used to communicate
with the firmware in the new AudioReach audio driver.
Lastly it transitions a number of drivers to safer string functions, as
well as switching things to use devm_platform_ioremap_resource().
-----BEGIN PGP SIGNATURE-----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=FE4j
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=LLU7
-----END PGP SIGNATURE-----
Merge tag 'qcom-drivers-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/drivers
Qualcomm driver updates for v5.16
This drops the use of power-domains for exposing the load_state from the
QMP driver to clients, to avoid issues related to system suspend.
SMP2P becomes wakeup capable, to allow dying remoteprocs to wake up
Linux from suspend to perform recovery.
It adds RPM power-domain support for SM6350 and MSM8953 and base RPM
support for MSM8953 and QCM2290.
It adds support for MSM8996, SDM630 and SDM660 in the SPM driver, which
will enable the introduction of proper voltage scaling of the CPU
subsystem.
Support for releasing secondary CPUs on MSM8226 is introduced.
The Asynchronous Packet Router (APR) driver is extended to support the
new Generic Packet Router (GPR) variant, which is used to communicate
with the firmware in the new AudioReach audio driver.
Lastly it transitions a number of drivers to safer string functions, as
well as switching things to use devm_platform_ioremap_resource().
* tag 'qcom-drivers-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (40 commits)
soc: qcom: apr: Add GPR support
soc: dt-bindings: qcom: add gpr bindings
soc: qcom: apr: make code more reuseable
soc: dt-bindings: qcom: apr: deprecate qcom,apr-domain property
soc: dt-bindings: qcom: apr: convert to yaml
dt-bindings: soc: qcom: aoss: Delete unused power-domain definitions
dt-bindings: msm/dp: Remove aoss-qmp header
soc: qcom: aoss: Drop power domain support
dt-bindings: soc: qcom: aoss: Drop the load state power-domain
soc: qcom: smp2p: Add wakeup capability to SMP2P IRQ
dt-bindings: power: rpmpd: Add SM6350 to rpmpd binding
dt-bindings: soc: qcom: aoss: Add SM6350 compatible
soc: qcom: llcc: Disable MMUHWT retention
soc: qcom: smd-rpm: Add QCM2290 compatible
dt-bindings: soc: qcom: smd-rpm: Add QCM2290 compatible
firmware: qcom_scm: Add compatible for MSM8953 SoC
dt-bindings: firmware: qcom-scm: Document msm8953 bindings
soc: qcom: pdr: Prefer strscpy over strcpy
soc: qcom: rpmh-rsc: Make use of the helper function devm_platform_ioremap_resource_byname()
soc: qcom: gsbi: Make use of the helper function devm_platform_ioremap_resource()
...
Link: https://lore.kernel.org/r/20211012173442.1017010-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Michael reported that when using the "ocelot-8021q" tagging protocol,
the switch driver module must be manually loaded before the tagging
protocol can be loaded/is available.
This appears to be the same problem described here:
https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
where due to the fact that DSA tagging protocols make use of symbols
exported by the switch drivers, circular dependencies appear and this
breaks module autoloading.
The ocelot_8021q driver needs the ocelot_can_inject() and
ocelot_port_inject_frame() functions from the switch library. Previously
the wrong approach was taken to solve that dependency: shims were
provided for the case where the ocelot switch library was compiled out,
but that turns out to be insufficient, because the dependency when the
switch lib _is_ compiled is problematic too.
We cannot declare ocelot_can_inject() and ocelot_port_inject_frame() as
static inline functions, because these access I/O functions like
__ocelot_write_ix() which is called by ocelot_write_rix(). Making those
static inline basically means exposing the whole guts of the ocelot
switch library, not ideal...
We already have one tagging protocol driver which calls into the switch
driver during xmit but not using any exported symbol: sja1105_defer_xmit.
We can do the same thing here: create a kthread worker and one work item
per skb, and let the switch driver itself do the register accesses to
send the skb, and then consume it.
Fixes: 0a6f17c6ae ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping")
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained here:
https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
DSA tagging protocol drivers cannot depend on symbols exported by switch
drivers, because this creates a circular dependency that breaks module
autoloading.
The tag_ocelot.c file depends on the ocelot_ptp_rew_op() function
exported by the common ocelot switch lib. This function looks at
OCELOT_SKB_CB(skb) and computes how to populate the REW_OP field of the
DSA tag, for PTP timestamping (the command: one-step/two-step, and the
TX timestamp identifier).
None of that requires deep insight into the driver, it is quite
stateless, as it only depends upon the skb->cb. So let's make it a
static inline function and put it in include/linux/dsa/ocelot.h, a
file that despite its name is used by the ocelot switch driver for
populating the injection header too - since commit 40d3f295b5 ("net:
mscc: ocelot: use common tag parsing code with DSA").
With that function declared as static inline, its body is expanded
inside each call site, so the dependency is broken and the DSA tagger
can be built without the switch library, upon which the felix driver
depends.
Fixes: 39e5308b32 ("net: mscc: ocelot: support PTP Sync one-step timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The sad reality is that when a PTP frame with a TX timestamping request
is transmitted, it isn't guaranteed that it will make it all the way to
the wire (due to congestion inside the switch), and that a timestamp
will be taken by the hardware and placed in the timestamp FIFO where an
IRQ will be raised for it.
The implication is that if enough PTP frames are silently dropped by the
hardware such that the timestamp ID has rolled over, it is possible to
match a timestamp to an old skb.
Furthermore, nobody will match on the real skb corresponding to this
timestamp, since we stupidly matched on a previous one that was stale in
the queue, and stopped there.
So PTP timestamping will be broken and there will be no way to recover.
It looks like the hardware parses the sequenceID from the PTP header,
and also provides that metadata for each timestamp. The driver currently
ignores this, but it shouldn't.
As an extra resiliency measure, do the following:
- check whether the PTP sequenceID also matches between the skb and the
timestamp, treat the skb as stale otherwise and free it
- if we see a stale skb, don't stop there and try to match an skb one
more time, chances are there's one more skb in the queue with the same
timestamp ID, otherwise we wouldn't have ever found the stale one (it
is by timestamp ID that we matched it).
While this does not prevent PTP packet drops, it at least prevents
the catastrophic consequences of incorrect timestamp matching.
Since we already call ptp_classify_raw in the TX path, save the result
in the skb->cb of the clone, and just use that result in the interrupt
code path.
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
PTP packets with 2-step TX timestamp requests are matched to packets
based on the egress port number and a 6-bit timestamp identifier.
All PTP timestamps are held in a common FIFO that is 128 entry deep.
This patch ensures that back-to-back timestamping requests cannot exceed
the hardware FIFO capacity. If that happens, simply send the packets
without requesting a TX timestamp to be taken (in the case of felix,
since the DSA API has a void return code in ds->ops->port_txtstamp) or
drop them (in the case of ocelot).
I've moved the ts_id_lock from a per-port basis to a per-switch basis,
because we need separate accounting for both numbers of PTP frames in
flight. And since we need locking to inc/dec the per-switch counter,
that also offers protection for the per-port counter and hence there is
no reason to have a per-port counter anymore.
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
At present, there is a problem when user space bombards a port with PTP
event frames which have TX timestamping requests (or when a tc-taprio
offload is installed on a port, which delays the TX timestamps by a
significant amount of time). The driver will happily roll over the 2-bit
timestamp ID and this will cause incorrect matches between an skb and
the TX timestamp collected from the FIFO.
The Ocelot switches have a 6-bit PTP timestamp identifier, and the value
63 is reserved, so that leaves identifiers 0-62 to be used.
The timestamp identifiers are selected by the REW_OP packet field, and
are actually shared between CPU-injected frames and frames which match a
VCAP IS2 rule that modifies the REW_OP. The hardware supports
partitioning between the two uses of the REW_OP field through the
PTP_ID_LOW and PTP_ID_HIGH registers, and by default reserves the PTP
IDs 0-3 for CPU-injected traffic and the rest for VCAP IS2.
The driver does not use VCAP IS2 to set REW_OP for 2-step timestamping,
and it also writes 0xffffffff to both PTP_ID_HIGH and PTP_ID_LOW in
ocelot_init_timestamp() which makes all timestamp identifiers available
to CPU injection.
Therefore, we can make use of all 63 timestamp identifiers, which should
allow more timestampable packets to be in flight on each port. This is
only part of the solution, more issues will be addressed in future changes.
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The PM stubs need to depend on ARCH_TEGRA in order to be usable for
compile-testing of tegra-cpuidle driver. Add the dependency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently the ocelot driver does support the 'vlan modify' action, but
in the ingress chain, and it is offloaded to VCAP IS1. This action
changes the classified VLAN before the packet enters the bridging
service, and the bridging works with the classified VLAN modified by
VCAP IS1.
That is good for some use cases, but there are others where the VLAN
must be modified at the stage of the egress port, after the packet has
exited the bridging service. One example is simulating IEEE 802.1CB
active stream identification filters ("active" means that not only the
rule matches on a packet flow, but it is also able to change some
headers). For example, a stream is replicated on two egress ports, but
they must have different VLAN IDs on egress ports A and B.
This seems like a task for the VCAP ES0, but that currently only
supports pushing the ES0 tag A, which is specified in the rule. Pushing
another VLAN header is not what we want, but rather overwriting the
existing one.
It looks like when we push the ES0 tag A, it is actually possible to not
only take the ES0 tag A's value from the rule itself (VID_A_VAL), but
derive it from the following formula:
ES0_TAG_A = Classified VID + VID_A_VAL
Otherwise said, ES0_TAG_A can be used to increment with a given value
the VLAN ID that the packet was already classified to, and the packet
will have this value as an outer VLAN tag. This new VLAN ID value then
gets stripped on egress (or not) according to the value of the native
VLAN from the bridging service.
While the hardware will happily increment the classified VLAN ID for all
packets that match the ES0 rule, in practice this would be rather
insane, so we only allow this kind of ES0 action if the ES0 filter
contains a VLAN ID too, so as to restrict the matching on a known
classified VLAN. If we program VID_A_VAL with the delta between the
desired final VLAN (ES0_TAG_A) and the classified VLAN, we obtain the
desired behavior.
It doesn't look like it is possible with the tc-vlan action to modify
the VLAN ID but not the PCP. In hardware it is possible to leave the PCP
to the classified value, but we unconditionally program it to overwrite
it with the PCP value from the rule.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ocelot_flower.c calls ocelot_vcap_filter_add(), the filter has a
given filter->id.cookie. This filter is added to the block->rules list.
However, when ocelot_flower.c calls ocelot_vcap_block_find_filter_by_id()
which passes the cookie as argument, the filter is never found by
filter->id.cookie when searching through the block->rules list.
This is unsurprising, since the filter->id.cookie is an unsigned long,
but the cookie argument provided to ocelot_vcap_block_find_filter_by_id()
is a signed int, and the comparison fails.
Fixes: 50c6cc5b92 ("net: mscc: ocelot: store a namespaced VCAP filter ID")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20210930125330.2078625-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement the support for SAW v4.1, used in at least MSM8998,
SDM630, SDM660 and APQ variants and, while at it, also add the
configuration for the SDM630/660 Silver and Gold cluster L2
Adaptive Voltage Scaler: this is also one of the prerequisites
to allow the OSM controller to perform DCVS.
Please note that despite there are various "versions" of these
values downstream, these are the only ones that are perfectly
stable on the entire set of tested devices.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210729155609.608159-4-angelogioacchino.delregno@somainline.org
In commit a871be6b8e ("cpuidle: Convert Qualcomm SPM driver to a generic
CPUidle driver") the SPM driver has been converted to a
generic CPUidle driver: that was mainly made to simplify the
driver and that was a great accomplishment;
Though, at that time, this driver was only applicable to ARM 32-bit SoCs,
lacking logic about the handling of newer generation SAW.
In preparation for the enablement of SPM features on AArch64/ARM64,
split the cpuidle-qcom-spm driver in two: the CPUIdle related
state machine (currently used only on ARM SoCs) stays there, while
the SPM communication handling lands back in soc/qcom/spm.c and
also making sure to not discard the simplifications that were
introduced in the aforementioned commit.
Since now the "two drivers" are split, the SCM dependency in the
main SPM handling is gone and for this reason it was also possible
to move the SPM initialization early: this will also make sure that
whenever the SAW CPUIdle driver is getting initialized, the SPM
driver will be ready to do the job.
Please note that the anticipation of the SPM initialization was
also done to optimize the boot times on platforms that have their
CPU/L2 idle states managed by other means (such as PSCI), while
needing SAW initialization for other purposes, like AVS control.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210729155609.608159-2-angelogioacchino.delregno@somainline.org
These are updates for drivers that are tied to a particular SoC,
including the correspondig device tree bindings:
- A couple of reset controller changes for unisoc, uniphier, renesas
and zte platforms
- memory controller driver fixes for omap and tegra
- Rockchip io domain driver updates
- Lots of updates for qualcomm platforms, mostly touching their
firmware and power management drivers
- Tegra FUSE and firmware driver updateѕ
- Support for virtio transports in the SCMI firmware framework
- cleanup of ixp4xx drivers, towards enabling multiplatform
support and bringing it up to date with modern platforms
- Minor updates for keystone, mediatek, omap, renesas.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iD8DBQBhLz215t5GS2LDRf4RAjlHAJ473D0PymaTzv68EuPHThG+DEPifQCdGjLq
QGBB6JidIP8rtEdC+LWBB8I=
=M5+N
-----END PGP SIGNATURE-----
Merge tag 'drivers-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are updates for drivers that are tied to a particular SoC,
including the correspondig device tree bindings:
- A couple of reset controller changes for unisoc, uniphier, renesas
and zte platforms
- memory controller driver fixes for omap and tegra
- Rockchip io domain driver updates
- Lots of updates for qualcomm platforms, mostly touching their
firmware and power management drivers
- Tegra FUSE and firmware driver updateѕ
- Support for virtio transports in the SCMI firmware framework
- cleanup of ixp4xx drivers, towards enabling multiplatform support
and bringing it up to date with modern platforms
- Minor updates for keystone, mediatek, omap, renesas"
* tag 'drivers-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (96 commits)
reset: simple: remove ZTE details in Kconfig help
soc: rockchip: io-domain: Remove unneeded semicolon
soc: rockchip: io-domain: add rk3568 support
dt-bindings: power: add rk3568-pmu-io-domain support
bus: ixp4xx: return on error in ixp4xx_exp_probe()
soc: renesas: Prefer memcpy() over strcpy()
firmware: tegra: Stop using seq_get_buf()
soc/tegra: fuse: Enable fuse clock on suspend for Tegra124
soc/tegra: fuse: Add runtime PM support
soc/tegra: fuse: Clear fuse->clk on driver probe failure
soc/tegra: pmc: Prevent racing with cpuilde driver
soc/tegra: bpmp: Remove unused including <linux/version.h>
dt-bindings: soc: ti: pruss: Add dma-coherent property
soc: ti: Remove pm_runtime_irq_safe() usage for smartreflex
soc: ti: pruss: Enable support for ICSSG subsystems on K3 AM64x SoCs
dt-bindings: soc: ti: pruss: Update bindings for K3 AM64x SoCs
firmware: arm_scmi: Use WARN_ON() to check configured transports
firmware: arm_scmi: Fix boolconv.cocci warnings
soc: mediatek: mmsys: Fix missing UFOE component in mt8173 table routing
soc: mediatek: mmsys: add MT8365 support
...
There are three noteworthy updates for 32-bit arm platforms this time:
- The Microchip SAMA7 family based on Cortex-A7 gets introduced, a new
cousin to the older SAM9 (ARM9xx based) and SAMA5 (Cortex-A5 based)
SoCs.
- The ixp4xx platform (based on Intel XScale) is finally converted to
device tree, and all the old board files are getting removed now.
- The Cirrus Logic EP93xx platform loses support for the old
MaverickCrunch FPU. Support for compiling user space applications
was already removed in gcc-4.9, and the kernel support for old
applications could not be built with clang ias. After confirming
that there are no remaining users, removing this from the kernel
seemed better than adding support for unused features to clang.
There are minor updates to the aspeed, omap and samsung platforms
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iD8DBQBhL0Bu5t5GS2LDRf4RAtYAAJ9qcN3tF8tHPPBUknXjvQVN7ESntwCfQtPu
XOVR6q993d7EZh3ATYuXVtE=
=igP/
-----END PGP SIGNATURE-----
Merge tag 'soc-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"There are three noteworthy updates for 32-bit arm platforms this time:
- The Microchip SAMA7 family based on Cortex-A7 gets introduced, a
new cousin to the older SAM9 (ARM9xx based) and SAMA5 (Cortex-A5
based) SoCs.
- The ixp4xx platform (based on Intel XScale) is finally converted to
device tree, and all the old board files are getting removed now.
- The Cirrus Logic EP93xx platform loses support for the old
MaverickCrunch FPU. Support for compiling user space applications
was already removed in gcc-4.9, and the kernel support for old
applications could not be built with clang ias. After confirming
that there are no remaining users, removing this from the kernel
seemed better than adding support for unused features to clang.
There are minor updates to the aspeed, omap and samsung platforms"
* tag 'soc-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (48 commits)
soc: aspeed-lpc-ctrl: Fix clock cleanup in error path
ARM: s3c: delete unneed local variable "delay"
soc: aspeed: Re-enable FWH2AHB on AST2600
soc: aspeed: socinfo: Add AST2625 variant
soc: aspeed: p2a-ctrl: Fix boundary check for mmap
soc: aspeed: lpc-ctrl: Fix boundary check for mmap
ARM: ixp4xx: Delete the Freecom FSG-3 boardfiles
ARM: ixp4xx: Delete GTWX5715 board files
ARM: ixp4xx: Delete Coyote and IXDPG425 boardfiles
ARM: ixp4xx: Delete Intel reference design boardfiles
ARM: ixp4xx: Delete Avila boardfiles
ARM: ixp4xx: Delete the Arcom Vulcan boardfiles
ARM: ixp4xx: Delete Gateway WG302v2 boardfiles
ARM: ixp4xx: Delete Omicron boardfiles
ARM: ixp4xx: Delete the D-Link DSM-G600 boardfiles
ARM: ixp4xx: Delete NAS100D boardfiles
ARM: ixp4xx: Delete NSLU2 boardfiles
arm: omap2: Drop the unused OMAP_PACKAGE_* KConfig entries
arm: omap2: Drop obsolete MACH_OMAP3_PANDORA entry
ARM: ep93xx: remove MaverickCrunch support
...
We need to transmit more restrictions in future patches, convert this
one to netlink extack.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to reject some more configurations in future patches, convert
the existing one to netlink extack.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements runtime PM support for the FUSE block and prepares the driver
to work better in conjunction with the CPUIDLE driver.
-----BEGIN PGP SIGNATURE-----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=migJ
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=GgIf
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.15-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/drivers
soc/tegra: Changes for v5.15-rc1
Implements runtime PM support for the FUSE block and prepares the driver
to work better in conjunction with the CPUIDLE driver.
* tag 'tegra-for-5.15-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: fuse: Enable fuse clock on suspend for Tegra124
soc/tegra: fuse: Add runtime PM support
soc/tegra: fuse: Clear fuse->clk on driver probe failure
soc/tegra: pmc: Prevent racing with cpuilde driver
soc/tegra: bpmp: Remove unused including <linux/version.h>
Link: https://lore.kernel.org/r/20210813162157.2820913-3-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The felix DSA driver, which is a wrapper over the same hardware class as
ocelot, is integrated with phylink, but ocelot is using the plain PHY
library. It makes sense to bring together the two implementations, which
is what this patch achieves.
This is a large patch and hard to break up, but it does the following:
The existing ocelot_adjust_link writes some registers, and
felix_phylink_mac_link_up writes some registers, some of them are
common, but both functions write to some registers to which the other
doesn't.
The main reasons for this are:
- Felix switches so far have used an NXP PCS so they had no need to
write the PCS1G registers that ocelot_adjust_link writes
- Felix switches have the MAC fixed at 1G, so some of the MAC speed
changes actually break the link and must be avoided.
The naming conventions for the functions introduced in this patch are:
- vsc7514_phylink_{mac_config,validate} are specific to the Ocelot
instantiations and placed in ocelot_net.c which is built only for the
ocelot switchdev driver.
- ocelot_phylink_mac_link_{up,down} are shared between the ocelot
switchdev driver and the felix DSA driver (they are put in the common
lib).
One by one, the registers written by ocelot_adjust_link are:
DEV_MAC_MODE_CFG - felix_phylink_mac_link_up had no need to write this
register since its out-of-reset value was fine and
did not need changing. The write is moved to the
common ocelot_phylink_mac_link_up and on felix it is
guarded by a quirk bit that makes the written value
identical with the out-of-reset one
DEV_PORT_MISC - runtime invariant, was moved to vsc7514_phylink_mac_config
PCS1G_MODE_CFG - same as above
PCS1G_SD_CFG - same as above
PCS1G_CFG - same as above
PCS1G_ANEG_CFG - same as above
PCS1G_LB_CFG - same as above
DEV_MAC_ENA_CFG - both ocelot_adjust_link and ocelot_port_disable
touched this. felix_phylink_mac_link_{up,down} also
do. We go with what felix does and put it in
ocelot_phylink_mac_link_up.
DEV_CLOCK_CFG - ocelot_adjust_link and felix_phylink_mac_link_up both
write this, but to different values. Move to the common
ocelot_phylink_mac_link_up and make sure via the quirk
that the old values are preserved for both.
ANA_PFC_PFC_CFG - ocelot_adjust_link wrote this, felix_phylink_mac_link_up
did not. Runtime invariant, speed does not matter since
PFC is disabled via the RX_PFC_ENA bits which are cleared.
Move to vsc7514_phylink_mac_config.
QSYS_SWITCH_PORT_MODE_PORT_ENA - both ocelot_adjust_link and
felix_phylink_mac_link_{up,down} wrote
this. Ocelot also wrote this register
from ocelot_port_disable. Keep what
felix did, move in ocelot_phylink_mac_link_{up,down}
and delete ocelot_port_disable.
ANA_POL_FLOWC - same as above
SYS_MAC_FC_CFG - same as above, except slight behavior change. Whereas
ocelot always enabled RX and TX flow control, felix
listened to phylink (for the most part, at least - see
the 2500base-X comment).
The registers which only felix_phylink_mac_link_up wrote are:
SYS_PAUSE_CFG_PAUSE_ENA - this is why I am not sure that flow control
worked on ocelot. Not it should, since the
code is shared with felix where it does.
ANA_PORT_PORT_CFG - this is a Frame Analyzer block register, phylink
should be the one touching them, deleted.
Other changes:
- The old phylib registration code was in mscc_ocelot_init_ports. It is
hard to work with 2 levels of indentation already in, and with hard to
follow teardown logic. The new phylink registration code was moved
inside ocelot_probe_port(), right between alloc_etherdev() and
register_netdev(). It could not be done before (=> outside of)
ocelot_probe_port() because ocelot_probe_port() allocates the struct
ocelot_port which we then use to assign ocelot_port->phy_mode to. It
is more preferable to me to have all PHY handling logic inside the
same function.
- On the same topic: struct ocelot_port_private :: serdes is only used
in ocelot_port_open to set the SERDES protocol to Ethernet. This is
logically a runtime invariant and can be done just once, when the port
registers with phylink. We therefore don't even need to keep the
serdes reference inside struct ocelot_port_private, or to use the devm
variant of of_phy_get().
- Phylink needs a valid phy-mode for phylink_create() to succeed, and
the existing device tree bindings in arch/mips/boot/dts/mscc/ocelot_pcb120.dts
don't define one for the internal PHY ports. So we patch
PHY_INTERFACE_MODE_NA into PHY_INTERFACE_MODE_INTERNAL.
- There was a strategically placed:
switch (priv->phy_mode) {
case PHY_INTERFACE_MODE_NA:
continue;
which made the code skip the serdes initialization for the internal
PHY ports. Frankly that is not all that obvious, so now we explicitly
initialize the serdes under an "if" condition and not rely on code
jumps, so everything is clearer.
- There was a write of OCELOT_SPEED_1000 to DEV_CLOCK_CFG for QSGMII
ports. Since that is in fact the default value for the register field
DEV_CLOCK_CFG_LINK_SPEED, I can only guess the intention was to clear
the adjacent fields, MAC_TX_RST and MAC_RX_RST, aka take the port out
of reset, which does match the comment. I don't even want to know why
this code is placed there, but if there is indeed an issue that all
ports that share a QSGMII lane must all be up, then this logic is
already buggy, since mscc_ocelot_init_ports iterates using
for_each_available_child_of_node, so nobody prevents the user from
putting a 'status = "disabled";' for some QSGMII ports which would
break the driver's assumption.
In any case, in the eventuality that I'm right, we would have yet
another issue if ocelot_phylink_mac_link_down would reset those ports
and that would be forbidden, so since the ocelot_adjust_link logic did
not do that (maybe for a reason), add another quirk to preserve the
old logic.
The ocelot driver teardown goes through all ports in one fell swoop.
When initialization of one port fails, the ocelot->ports[port] pointer
for that is reset to NULL, and teardown is done only for non-NULL ports,
so there is no reason to do partial teardowns, let the central
mscc_ocelot_release_ports() do its job.
Tested bind, unbind, rebind, link up, link down, speed change on mock-up
hardware (modified the driver to probe on Felix VSC9959). Also
regression tested the felix DSA driver. Could not test the Ocelot
specific bits (PCS1G, SERDES, device tree bindings).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ocelot_port_enable touches ANA_PORT_PORT_CFG, which has the following
fields:
- LOCKED_PORTMOVE_CPU, LEARNDROP, LEARNCPU, LEARNAUTO, RECV_ENA, all of
which are written with their hardware default values, also runtime
invariants. So it makes no sense to write these during every .ndo_open.
- PORTID_VAL: this field has an out-of-reset value of zero for all ports
and must be initialized by software. Additionally, the
ocelot_setup_logical_port_ids() code path sets up different logical
port IDs for the ports in a hardware LAG, and we absolutely don't want
.ndo_open to interfere there and reset those values.
So in fact the write from ocelot_port_enable can better be moved to
ocelot_init_port, and the .ndo_open hook deleted.
ocelot_port_disable touches DEV_MAC_ENA_CFG and QSYS_SWITCH_PORT_MODE_PORT_ENA,
in an attempt to undo what ocelot_adjust_link did. But since .ndo_stop
does not get called each time the link falls (i.e. this isn't a
substitute for .phylink_mac_link_down), felix already does better at
this by writing those registers already in felix_phylink_mac_link_down.
So keep ocelot_port_disable (for now, until ocelot is converted to
phylink too), and just delete the felix call to it, which is not
necessary.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both PMC and cpuidle drivers are probed at the same init level and
cpuidle depends on the PMC suspend mode. Add new default suspend mode
that indicates whether PMC driver has been probed and reset the mode in
a case of deferred probe of the PMC driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
- add new SoC based on a Cortex-A7 core: the SAMA7G5 family
- mach-at91 entry, Kconfig and header files
- Power Management Controller (PMC) code and associated power management
changes. Support for suspend/resume, Ultra Low Power modes and
Backup with Memory in Self-Refresh mode.
- Power management association with DDR controller and
shutdown controller for addressing this variety of modes.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ5TRCVIBiyi/S+BG4fOrpwrNPNDAUCYQpPnQAKCRAfOrpwrNPN
DJyeAQDvS538E7jFPdsmUn3iZhMhV4zCZVsPk9fox9ptV8ewEAD/QuWFZg78YkZE
vGe/AXlxjA4V/TMiGElf0/nbZ8xLiw4=
=YucO
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=+KcA
-----END PGP SIGNATURE-----
Merge tag 'at91-soc-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/soc
AT91 soc for 5.15:
- add new SoC based on a Cortex-A7 core: the SAMA7G5 family
- mach-at91 entry, Kconfig and header files
- Power Management Controller (PMC) code and associated power management
changes. Support for suspend/resume, Ultra Low Power modes and
Backup with Memory in Self-Refresh mode.
- Power management association with DDR controller and
shutdown controller for addressing this variety of modes.
* tag 'at91-soc-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux: (26 commits)
ARM: at91: pm: add sama7g5 shdwc
ARM: at91: pm: add pm support for SAMA7G5
ARM: at91: sama7: introduce sama7 SoC family
ARM: at91: pm: add sama7g5's pmc
ARM: at91: pm: add backup mode support for SAMA7G5
ARM: at91: pm: save ddr phy calibration data to securam
ARM: at91: pm: add sama7g5 ddr phy controller
ARM: at91: pm: add sama7g5 ddr controller
ARM: at91: pm: wait for ddr power mode off
ARM: at91: pm: add support for 2.5V LDO regulator control
ARM: at91: pm: add support for MCK1..4 save/restore for ulp modes
ARM: at91: pm: add self-refresh support for sama7g5
ARM: at91: ddr: add registers definitions for sama7g5's ddr
ARM: at91: sfrbu: add sfrbu registers definitions for sama7g5
ARM: at91: pm: add support for waiting MCK1..4
ARM: at91: pm: s/CONFIG_SOC_SAM9X60/CONFIG_HAVE_AT91_SAM9X60_PLL/g
ARM: at91: pm: avoid push and pop on stack while memory is in self-refersh
ARM: at91: pm: use r7 instead of tmp1
ARM: at91: pm: do not initialize pdev
ARM: at91: pm: check for different controllers in at91_pm_modes_init()
...
Link: https://lore.kernel.org/r/20210804084316.12641-1-nicolas.ferre@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Reset controllers: Adding support for Microchip Sparx5 Switch.
- Memory controllers: ARM Primecell PL35x SMC memory controller
driver cleanups and improvements.
- i.MX SoC drivers: Power domain support for i.MX8MM and i.MX8MN.
- Rockchip: RK3568 power domains support + DT binding updates,
cleanups.
- Qualcomm SoC drivers: Amend socinfo with more SoC/PMIC details,
including support for MSM8226, MDM9607, SM6125 and SC8180X.
- ARM FFA driver: "Firmware Framework for ARMv8-A", defining
management interfaces and communication (including bus model)
between partitions both in Normal and Secure Worlds.
- Tegra Memory controller changes, including major rework to deal
with identity mappings at boot and integration with ARM SMMU
pieces.
-----BEGIN PGP SIGNATURE-----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=kPg8
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM driver updates from Olof Johansson:
- Reset controllers: Adding support for Microchip Sparx5 Switch.
- Memory controllers: ARM Primecell PL35x SMC memory controller driver
cleanups and improvements.
- i.MX SoC drivers: Power domain support for i.MX8MM and i.MX8MN.
- Rockchip: RK3568 power domains support + DT binding updates,
cleanups.
- Qualcomm SoC drivers: Amend socinfo with more SoC/PMIC details,
including support for MSM8226, MDM9607, SM6125 and SC8180X.
- ARM FFA driver: "Firmware Framework for ARMv8-A", defining management
interfaces and communication (including bus model) between partitions
both in Normal and Secure Worlds.
- Tegra Memory controller changes, including major rework to deal with
identity mappings at boot and integration with ARM SMMU pieces.
* tag 'arm-drivers-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (120 commits)
firmware: turris-mox-rwtm: add marvell,armada-3700-rwtm-firmware compatible string
firmware: turris-mox-rwtm: show message about HWRNG registration
firmware: turris-mox-rwtm: fail probing when firmware does not support hwrng
firmware: turris-mox-rwtm: report failures better
firmware: turris-mox-rwtm: fix reply status decoding function
soc: imx: gpcv2: add support for i.MX8MN power domains
dt-bindings: add defines for i.MX8MN power domains
firmware: tegra: bpmp: Fix Tegra234-only builds
iommu/arm-smmu: Use Tegra implementation on Tegra186
iommu/arm-smmu: tegra: Implement SID override programming
iommu/arm-smmu: tegra: Detect number of instances at runtime
dt-bindings: arm-smmu: Add Tegra186 compatible string
firmware: qcom_scm: Add MDM9607 compatible
soc: qcom: rpmpd: Add MDM9607 RPM Power Domains
soc: renesas: Add support to read LSI DEVID register of RZ/G2{L,LC} SoC's
soc: renesas: Add ARCH_R9A07G044 for the new RZ/G2L SoC's
dt-bindings: soc: rockchip: drop unnecessary #phy-cells from grf.yaml
memory: emif: remove unused frequency and voltage notifiers
memory: fsl_ifc: fix leak of private memory on probe failure
memory: fsl_ifc: fix leak of IO mapping on probe failure
...
A few SoC (code) changes have queued up this cycle, mostly for minor
changes and some refactoring and cleanup of legacy platforms. This
branch also contains a few of the fixes that weren't sent in by the end
of the release (all fairly minor).
- Adding an additional maintainer for the TEE subsystem (Sumit Garg)
- Quite a significant modernization of the IXP4xx platforms by Linus
Walleij, revisiting with a new PCI host driver/binding, removing legacy
mach/* include dependencies and moving platform detection/config to
drivers/soc. Also some updates/cleanup of platform data.
- Core power domain support for Tegra platforms, and some improvements
in build test coverage by adding stubs for compile test targets.
- A handful of updates to i.MX platforms, adding legacy (non-PSCI) SMP
support on i.MX7D, SoC ID setup for i.MX50, removal of platform data
and board fixups for iMX6/7.
... and a few smaller changes and fixes for Samsung, OMAP, Allwinner,
Rockchip.
-----BEGIN PGP SIGNATURE-----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=b6Jo
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Olof Johansson:
"A few SoC (code) changes have queued up this cycle, mostly for minor
changes and some refactoring and cleanup of legacy platforms. This
branch also contains a few of the fixes that weren't sent in by the
end of the release (all fairly minor).
- Adding an additional maintainer for the TEE subsystem (Sumit Garg)
- Quite a significant modernization of the IXP4xx platforms by Linus
Walleij, revisiting with a new PCI host driver/binding, removing
legacy mach/* include dependencies and moving platform
detection/config to drivers/soc. Also some updates/cleanup of
platform data.
- Core power domain support for Tegra platforms, and some
improvements in build test coverage by adding stubs for compile
test targets.
- A handful of updates to i.MX platforms, adding legacy (non-PSCI)
SMP support on i.MX7D, SoC ID setup for i.MX50, removal of platform
data and board fixups for iMX6/7.
... and a few smaller changes and fixes for Samsung, OMAP, Allwinner,
Rockchip"
* tag 'arm-soc-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (53 commits)
MAINTAINERS: Add myself as TEE subsystem reviewer
ixp4xx: fix spelling mistake in Kconfig "Devce" -> "Device"
hw_random: ixp4xx: Add OF support
hw_random: ixp4xx: Add DT bindings
hw_random: ixp4xx: Turn into a module
hw_random: ixp4xx: Use SPDX license tag
hw_random: ixp4xx: enable compile-testing
pata: ixp4xx: split platform data to its own header
soc: ixp4xx: move cpu detection to linux/soc/ixp4xx/cpu.h
PCI: ixp4xx: Add a new driver for IXP4xx
PCI: ixp4xx: Add device tree bindings for IXP4xx
ARM/ixp4xx: Make NEED_MACH_IO_H optional
ARM/ixp4xx: Move the virtual IObases
MAINTAINERS: ARM/MStar/Sigmastar SoCs: Add a link to the MStar tree
ARM: debug: add UART early console support for MSTAR SoCs
ARM: dts: ux500: Fix LED probing
ARM: imx: add smp support for imx7d
ARM: imx6q: drop of_platform_default_populate() from init_machine
arm64: dts: rockchip: Update RK3399 PCI host bridge window to 32-bit address memory
soc/tegra: fuse: Fix Tegra234-only builds
...
This driver adds support for the single mailbox channel of the MSS
system controller on the Microchip PolarFire SoC.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The tegra_mc_probe_device() symbol is only available when the TEGRA_MC
Kconfig option is enabled. Provide a stub if that's not the case so that
the driver can be compile-tested.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210618111846.1286166-1-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
These changes implement the core power domain for the PMC, and fix a
couple of minor issues as well as add stubs to help some drivers be
compile tested more easily.
-----BEGIN PGP SIGNATURE-----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=g0AU
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.14-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/soc
soc/tegra: Changes for v5.14-rc1
These changes implement the core power domain for the PMC, and fix a
couple of minor issues as well as add stubs to help some drivers be
compile tested more easily.
* tag 'tegra-for-5.14-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: fuse: Fix Tegra234-only builds
soc/tegra: fuse: Don't return -ENOMEM when allocate lookups failed
soc/tegra: regulators: Support core domain state syncing
soc/tegra: pmc: Add driver state syncing
soc/tegra: pmc: Add core power domain
soc/tegra: fuse: Add stubs needed for compile-testing
soc/tegra: Add devm_tegra_core_dev_init_opp_table()
soc/tegra: Add stub for soc_is_tegra()
soc/tegra: regulators: Bump voltages on system reboot
regulator: core: Add regulator_sync_voltage_rdev()
Link: https://lore.kernel.org/r/20210611164437.3568059-2-thierry.reding@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Instead of programming all SID overrides during early boot, perform the
operation on-demand after the SMMU translations have been set up for a
device. This reuses data from device tree to match memory clients for a
device and programs the SID specified in device tree, which corresponds
to the SID used for the SMMU context banks for the device.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210603164632.1000458-2-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
The Tegra210 (and earlier) driver now supports all the functionality
that the Tegra186 (and later) driver does, so they can be unified.
Note that previously the Tegra186 (and later) driver could be unloaded,
even if that was perhaps not very useful. Older chips don't support that
yet, but once they do this code can be reenabled.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-11-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Tegra20 requires a slightly different interrupt handler than Tegra30 and
later, so parameterize the handler, so that each SoC implementation can
provide its own.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-8-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
The current per-SoC setup code runs at a fairly arbitrary point during
probe, thereby making it less flexible for other SoC generations. Move
the call around slightly (after only the very basic, common setup that
applies to all SoC generations has been performed), which will allow
it to be used for other implementations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-6-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Continuing the scheme of unification, push suspend/resume callbacks into
per-SoC driver so that they can be properly parameterized.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-5-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Subsequent patches will introduce further callbacks, so create a new
struct tegra_mc_ops to collect all of them in a single place. Move the
existing ->init() callback into the new structure.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-4-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
As another step towards unifying both the Tegra210 (and earlier) and
Tegra186 (and later) memory controller drivers, unify the structures
that are used to represent them.
Note that this comes at a slight space penalty since some fields are
not used on all generations, but the benefits of unifying the driver
outweigh the downsides.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-3-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Subsequent patches will add more register fields to the tegra_mc_client
structure, so consolidate all register field definitions into a common
sub-structure for coherency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-2-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Add driver state syncing that is invoked once all PMC consumers are
attached and ready. The consumers are the power domain clients.
The synchronization callback is invoked once all client drivers are
probed, the driver core handles this for us. This callback informs
PMC driver that all voltage votes are initialized by each PD client
and it's safe to begin voltage scaling of the core power domain.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
[treding@nvidia.com: squash DT backwards-compatibility patch]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add missing stubs that will allow Tegra memory driver to be compile-tested
by kernel build bots.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
As on i.MX51 and i.MX53, initialize the SoC ID based on the SoC
compatible string of the board.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to
walk all map elements in a more robust and easier to verify
fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF
on s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices
which don't need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability
on next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is
slow in reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take
place correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP
packets before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used
to define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
-independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and
bnxt support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP
which define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay
for packets sampled from switch HW (and corresponding egress
and policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP
forwarding, bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface
to distribute MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x -
11-port Ethernet switch with 8x 1-Gigabit Ethernet
and 3x 10-Gigabit interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365
and BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack,
matching on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode
changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=vcbA
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to walk
all map elements in a more robust and easier to verify fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF on
s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices which don't
need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability on
next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is slow in
reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take place
correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP packets
before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used to
define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and bnxt
support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP which
define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay for
packets sampled from switch HW (and corresponding egress and
policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP forwarding,
bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface to distribute
MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x - 11-port
Ethernet switch with 8x 1-Gigabit Ethernet and 3x 10-Gigabit
interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365 and
BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack, matching
on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes"
* tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2451 commits)
net: selftest: fix build issue if INET is disabled
net: netrom: nr_in: Remove redundant assignment to ns
net: tun: Remove redundant assignment to ret
net: phy: marvell: add downshift support for M88E1240
net: dsa: ksz: Make reg_mib_cnt a u8 as it never exceeds 255
net/sched: act_ct: Remove redundant ct get and check
icmp: standardize naming of RFC 8335 PROBE constants
bpf, selftests: Update array map tests for per-cpu batched ops
bpf: Add batched ops support for percpu array
bpf: Implement formatted output helpers with bstr_printf
seq_file: Add a seq_bprintf function
sfc: adjust efx->xdp_tx_queue_count with the real number of initialized queues
net:nfc:digital: Fix a double free in digital_tg_recv_dep_req
net: fix a concurrency bug in l2tp_tunnel_register()
net/smc: Remove redundant assignment to rc
mpls: Remove redundant assignment to err
llc2: Remove redundant assignment to rc
net/tls: Remove redundant initialization of record
rds: Remove redundant assignment to nr_sig
dt-bindings: net: mdio-gpio: add compatible for microchip,mdio-smi0
...
Although HWTSTAMP_TX_ONESTEP_SYNC existed in ioctl for hardware timestamp
configuration, the PTP Sync one-step timestamping had never been supported.
This patch is to truely support it.
- ocelot_port_txtstamp_request()
This function handles tx timestamp request by storing
ptp_cmd(tx timestamp type) in OCELOT_SKB_CB(skb)->ptp_cmd,
and additionally for two-step timestamp storing ts_id in
OCELOT_SKB_CB(clone)->ptp_cmd.
- ocelot_ptp_rew_op()
During xmit, this function is called to get rew_op (rewriter option) by
checking skb->cb for tx timestamp request, and configure to transmitting.
Non-onestep-Sync packet with one-step timestamp request falls back to use
two-step timestamp.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to a common ocelot_port_txtstamp_request() for TX timestamp
request handling.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free skb->cb usage in core driver and let device drivers decide to
use or not. The reason having a DSA_SKB_CB(skb)->clone was because
dsa_skb_tx_timestamp() which may set the clone pointer was called
before p->xmit() which would use the clone if any, and the device
driver has no way to initialize the clone pointer.
This patch just put memset(skb->cb, 0, sizeof(skb->cb)) at beginning
of dsa_slave_xmit(). Some new features in the future, like one-step
timestamp may need more bytes of skb->cb to use in
dsa_skb_tx_timestamp(), and p->xmit().
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updates for SoC specific drivers include a few subsystems that
have their own maintainers but send them through the soc tree:
TEE/OP-TEE:
- Add tracepoints around calls to secure world
Memory controller drivers:
- Minor fixes for Renesas, Exynos, Mediatek and Tegra platforms
- Add debug statistics to Tegra20 memory controller
- Update Tegra bindings and convert to dtschema
ARM SCMI Firmware:
- Support for modular SCMI protocols and vendor specific extensions
- New SCMI IIO driver
- Per-cpu DVFS
The other driver changes are all from the platform maintainers
directly and reflect the drivers that don't fit into any other
subsystem as well as treewide changes for a particular platform.
SoCFPGA:
- Various cleanups contributed by Krzysztof Kozlowski
Mediatek:
- add MT8183 support to mutex driver
- MMSYS: use per SoC array to describe the possible routing
- add MMSYS support for MT8183 and MT8167
- add support for PMIC wrapper with integrated arbiter
- add support for MT8192/MT6873
Tegra:
- Bug fixes to PMC and clock drivers
NXP/i.MX:
- Update SCU power domain driver to keep console domain power on.
- Add missing ADC1 power domain to SCU power domain driver.
- Update comments for single global power domain in SCU power domain
driver.
- Add i.MX51/i.MX53 unique id support to i.MX SoC driver.
NXP/FSL SoC driver updates for v5.13
- Add ACPI support for RCPM driver
- Use generic io{read,write} for QE drivers after performance optimized
for PowerPC
- Fix QBMAN probe to cleanup HW states correctly for kexec
- Various cleanup and style fix for QBMAN/QE/GUTS drivers
OMAP:
- Preparation to use devicetree for genpd
- ti-sysc needs iorange check improved when the interconnect target module
has no control registers listed
- ti-sysc needs to probe l4_wkup and l4_cfg interconnects first to avoid
issues with missing resources and unnecessary deferred probe
- ti-sysc debug option can now detect more devices
- ti-sysc now warns if an old incomplete devicetree data is found as we
now rely on it being complete for am3 and 4
- soc init code needs to check for prcm and prm nodes for omap4/5 and dra7
- omap-prm driver needs to enable autoidle retention support for omap4
- omap5 clocks are missing gpmc and ocmc clock registers
- pci-dra7xx now needs to use builtin_platform_driver instead of using
builtin_platform_driver_probe for deferred probe to work
Raspberry Pi:
- Fix-up all RPi firmware drivers so as for unbind to happen in an
orderly fashion
- Support for RPi's PoE hat PWM bus
Qualcomm
- Improved detection for SCM calling conventions
- Support for OEM specific wifi firmware path
- Added drivers for SC7280/SM8350: RPMH, LLCC< AOSS QMP
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=iidq
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Updates for SoC specific drivers include a few subsystems that have
their own maintainers but send them through the soc tree:
TEE/OP-TEE:
- Add tracepoints around calls to secure world
Memory controller drivers:
- Minor fixes for Renesas, Exynos, Mediatek and Tegra platforms
- Add debug statistics to Tegra20 memory controller
- Update Tegra bindings and convert to dtschema
ARM SCMI Firmware:
- Support for modular SCMI protocols and vendor specific extensions
- New SCMI IIO driver
- Per-cpu DVFS
The other driver changes are all from the platform maintainers
directly and reflect the drivers that don't fit into any other
subsystem as well as treewide changes for a particular platform.
SoCFPGA:
- Various cleanups contributed by Krzysztof Kozlowski
Mediatek:
- add MT8183 support to mutex driver
- MMSYS: use per SoC array to describe the possible routing
- add MMSYS support for MT8183 and MT8167
- add support for PMIC wrapper with integrated arbiter
- add support for MT8192/MT6873
Tegra:
- Bug fixes to PMC and clock drivers
NXP/i.MX:
- Update SCU power domain driver to keep console domain power on.
- Add missing ADC1 power domain to SCU power domain driver.
- Update comments for single global power domain in SCU power domain
driver.
- Add i.MX51/i.MX53 unique id support to i.MX SoC driver.
NXP/FSL SoC driver updates for v5.13
- Add ACPI support for RCPM driver
- Use generic io{read,write} for QE drivers after performance
optimized for PowerPC
- Fix QBMAN probe to cleanup HW states correctly for kexec
- Various cleanup and style fix for QBMAN/QE/GUTS drivers
OMAP:
- Preparation to use devicetree for genpd
- ti-sysc needs iorange check improved when the interconnect target
module has no control registers listed
- ti-sysc needs to probe l4_wkup and l4_cfg interconnects first to
avoid issues with missing resources and unnecessary deferred probe
- ti-sysc debug option can now detect more devices
- ti-sysc now warns if an old incomplete devicetree data is found as
we now rely on it being complete for am3 and 4
- soc init code needs to check for prcm and prm nodes for omap4/5 and
dra7
- omap-prm driver needs to enable autoidle retention support for
omap4
- omap5 clocks are missing gpmc and ocmc clock registers
- pci-dra7xx now needs to use builtin_platform_driver instead of
using builtin_platform_driver_probe for deferred probe to work
Raspberry Pi:
- Fix-up all RPi firmware drivers so as for unbind to happen in an
orderly fashion
- Support for RPi's PoE hat PWM bus
Qualcomm
- Improved detection for SCM calling conventions
- Support for OEM specific wifi firmware path
- Added drivers for SC7280/SM8350: RPMH, LLCC< AOSS QMP"
* tag 'arm-drivers-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
soc: aspeed: fix a ternary sign expansion bug
memory: mtk-smi: Add device-link between smi-larb and smi-common
memory: samsung: exynos5422-dmc: handle clk_set_parent() failure
memory: renesas-rpc-if: fix possible NULL pointer dereference of resource
clk: socfpga: fix iomem pointer cast on 64-bit
soc: aspeed: Adapt to new LPC device tree layout
pinctrl: aspeed-g5: Adapt to new LPC device tree layout
ipmi: kcs: aspeed: Adapt to new LPC DTS layout
ARM: dts: Remove LPC BMC and Host partitions
dt-bindings: aspeed-lpc: Remove LPC partitioning
soc: fsl: enable acpi support in RCPM driver
soc: qcom: mdt_loader: Detect truncated read of segments
soc: qcom: mdt_loader: Validate that p_filesz < p_memsz
soc: qcom: pdr: Fix error return code in pdr_register_listener
firmware: qcom_scm: Fix kernel-doc function names to match
firmware: qcom_scm: Suppress sysfs bind attributes
firmware: qcom_scm: Workaround lack of "is available" call on SC7180
firmware: qcom_scm: Reduce locking section for __get_convention()
firmware: qcom_scm: Make __qcom_scm_is_call_available() return bool
Revert "soc: fsl: qe: introduce qe_io{read,write}* wrappers"
...
- Add ACPI support for RCPM driver
- Use generic io{read,write} for QE drivers after performance optimized
for PowerPC
- Fix QBMAN probe to cleanup HW states correctly for kexec
- Various cleanup and style fix for QBMAN/QE/GUTS drivers
-----BEGIN PGP SIGNATURE-----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=+DV0
-----END PGP SIGNATURE-----
Merge tag 'soc-fsl-next-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into arm/drivers
NXP/FSL SoC driver updates for v5.13
- Add ACPI support for RCPM driver
- Use generic io{read,write} for QE drivers after performance optimized
for PowerPC
- Fix QBMAN probe to cleanup HW states correctly for kexec
- Various cleanup and style fix for QBMAN/QE/GUTS drivers
* tag 'soc-fsl-next-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
soc: fsl: enable acpi support in RCPM driver
Revert "soc: fsl: qe: introduce qe_io{read,write}* wrappers"
tty: serial: ucc_uart: replace qe_io{read,write}* wrappers by generic io{read,write}*
soc: fsl: qe: replace qe_io{read,write}* wrappers by generic io{read,write}*
soc: fsl: guts: fix comment syntax in file
soc: fsl: guts: remove unneeded semicolon
soc: fsl: qe: Use DEFINE_SPINLOCK() for spinlock
soc: fsl: qbman: Delete useless kfree code
soc: fsl: qbman: Ensure device cleanup is run for kexec
Link: https://lore.kernel.org/r/20210409205719.27927-1-leoyang.li@nxp.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
1. Few cleanups.
2. Add debug statistics to Tegra20 memory controller.
3. Update bindings and convert to dtschema. This update is not
backwards compatible (ABI break) however the broken part was added
recently (v5.11) and there are no users of it yet.
-----BEGIN PGP SIGNATURE-----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=bbW2
-----END PGP SIGNATURE-----
Merge tag 'memory-controller-drv-tegra-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl into arm/drivers
Memory controller drivers for v5.13 - Tegra SoC
1. Few cleanups.
2. Add debug statistics to Tegra20 memory controller.
3. Update bindings and convert to dtschema. This update is not
backwards compatible (ABI break) however the broken part was added
recently (v5.11) and there are no users of it yet.
* tag 'memory-controller-drv-tegra-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
dt-bindings: memory: tegra20: mc: Convert to schema
dt-bindings: memory: tegra124: emc: Replace core regulator with power domain
dt-bindings: memory: tegra30: emc: Replace core regulator with power domain
dt-bindings: memory: tegra20: emc: Replace core regulator with power domain
memory: tegra: Print out info-level once per driver probe
memory: tegra20: Protect debug code with a lock
memory: tegra20: Correct comment to MC_STAT registers writes
memory: tegra20: Add debug statistics
memory: tegra: replace DEFINE_SIMPLE_ATTRIBUTE with DEFINE_DEBUGFS_ATTRIBUTE
Link: https://lore.kernel.org/r/20210407161333.73013-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We have currently three users of the PSEC_PER_SEC each of them defining it
individually. Instead, move it to time64.h to be available for everyone.
There is a new user coming with the same constant in use. It will also
make its life easier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 6ac9b61786.
This commit was required because at that time, ioread/iowrite
functions were sub-optimal on powerpc/32 compared to the
architecture specific in_/out_ IO accessors.
But there are now equivalent since
commit 894fa235eb ("powerpc: inline iomap accessors").
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Claudiu Beznea