AL3320a is fairly simple chip, so for suspend is enough to disable and
later enable it again.
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Based on:
- 3320A in-kernel driver
- https://www.spinics.net/lists/linux-iio/msg25145.html
- https://lore.kernel.org/patchwork/patch/684179/
I decided to keep it aside of AL3320A due to different approach and much
simpler design of 3010.
Tested on Nexus 7 2012 (grouper/tilapia).
Tested-by: David Heidelberg <david@ixit.cz>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
- modified to be in part with al3010 driver
- cleanup using bitfield, no functionality change intended
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Vishay has published a new version of "Designing the VCNL4200 Into an
Application" application note in October 2019. The new version specifies
that there is +-20% of part to part tolerance. Although the application
note is related to vcnl4200, according to support the vcnl4040's "ASIC
is quite similar to that one for the VCNL4200".
So update the sampling periods (and comment), including the correct
sampling period for proximity. Both sampling periods are lower. Users
relying on the blocking behaviour of reading will get proximity
measurements much earlier.
Fixes: 5a441aade5 ("iio: light: vcnl4000 add support for the VCNL4040 proximity and light sensor")
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Tested-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Vishay has published a new version of "Designing the VCNL4200 Into an
Application" application note in October 2019. The new version specifies
that there is +-20% of part to part tolerance. This explains the drift
seen during experiments. The proximity pulse width is also changed from
32us to 30us. According to the support, the tolerance also applies to
ambient light.
So update the sampling periods. As the reading is blocking, current
users may notice slightly longer response time.
Fixes: be38866fbb ("iio: vcnl4000: add support for VCNL4200")
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This is modelled after the vcnl4035 driver. For the vcnl40{0,1,2}0
we don't do anything since they use on demand measurement.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This will be useful when introducing runtime pm.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver handles two different Sharp sensors that have been
proposed for merging to the mainline kernel over the years, and
already has a limited proximity-only driver in the input
subsystem.
These components are completely different from the confusingly
similarly named Sharp GP2AP020A00F, for which we have a driver
in drivers/iio/light/gp2ap020a00f.c
The two components GP2AP002A00F and GP2AP002S00F are
distinctively different but similar: they share the same set of
registers but differ slightly in the I2C protocol.
Instead of the approach by the previous input driver, we create
a combined IIO proximity and light sensor driver.
The plan is to merge this driver and delete the input driver.
The pieces for the driver are picked all over the place after
researching and grepping through a few different vendor trees
and driver submissions.
We merge it under the light sensors because:
- It has similarities with the Capella CM3605 light sensor and
proximity driver which is there.
- It is related to the GP2AP020A00F driver which is also there.
This driver was tested with the Samsung GT-S7710 mobile phone
which has the GP2AP002S00F proximity sensor mounted.
The suspend/resume cycle will disable the interrupt from the
sensor. If someone would desire to use this interrupt for
wakeup, the driver will need modifications.
Cc: Stephan Gerhold <stephan@gerhold.net>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Cc: Jonathan Bakker <xc-racer2@live.ca>
Cc: Oskar Andero <oskar.andero@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* CrOS EC
- Refactoring of some of cros_ec's headers. include/linux/mfd/cros_ec.h now
removed, new cros_ec.h added drivers/platform/chrome which contains shared
operations of cros_ec transport drivers.
- Response tracing in cros_ec_proto
* Wilco EC
- Fix unregistration order.
- Fix keyboard backlight probing on systems without keyboard backlight
- Minor cleanup (newlines in printks, COMPILE_TEST)
* Misc
- chromeos_laptop converted to use i2c_new_scanned_device instead of
i2c_new_probed_device
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQCtZK6p/AktxXfkOlzbaomhzOwwgUCXjij4AAKCRBzbaomhzOw
wrFjAP0bU5PFkxprCOTY9kF/cMgHPDljEPES4FVV11eGyYr3HgD/StpuIhFGrh7+
Fz96dDdNu1melyGjmMqSN/M9JFo+Hw4=
=FB/I
-----END PGP SIGNATURE-----
Merge tag 'tag-chrome-platform-for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung:
"CrOS EC:
- Refactoring of some of cros_ec's headers:
include/linux/mfd/cros_ec.h now removed, new cros_ec.h added to
drivers/platform/chrome which contains shared operations of cros_ec
transport drivers.
- Response tracing in cros_ec_proto
Wilco EC:
- Fix unregistration order.
- Fix keyboard backlight probing on systems without keyboard
backlight
- Minor cleanup (newlines in printks, COMPILE_TEST)
Misc:
- chromeos_laptop converted to use i2c_new_scanned_device instead of
i2c_new_probed_device"
* tag 'tag-chrome-platform-for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: cros_ec: Match implementation with headers
platform/chrome: cros_ec: Drop unaligned.h include
platform/chrome: wilco_ec: Allow wilco to be compiled in COMPILE_TEST
platform/chrome: wilco_ec: Add newlines to printks
platform/chrome: wilco_ec: Fix unregistration order
cros_ec: treewide: Remove 'include/linux/mfd/cros_ec.h'
platform/chrome: cros_ec_ishtp: Make init_lock static
platform/chrome: chromeos_laptop: Convert to i2c_new_scanned_device
platform/chrome: cros_ec_lpc: Use platform_get_irq_optional() for optional IRQs
platform/chrome: cros_ec_proto: Add response tracing
platform/chrome: cros_ec_trace: Match trace commands with EC commands
According to the data sheet the ambient sensor's scale is 0.12 lux/step
(not 0.024 lux/step as used by vcnl4200) when the integration time is
80ms. The integration time is currently hardcoded in the driver to that
value.
See p. 8 in https://www.vishay.com/docs/84307/designingvcnl4040.pdf
Fixes: 5a441aade5 ("iio: light: vcnl4000 add support for the VCNL4040 proximity and light sensor")
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New device support
* ad7091r5 ADC
- New driver with follow up patch adding scale and vref support.
- DT bindings
* ad7923
- Support for ad7908, ad7918 and ad7928 added to driver.
* bma180
- Support the BMA254 accelerometer. Required fairly substantial rework
to allow for small differences between this an existing parts.
* bma400 accelerometer
- New driver with follow up patch for regulator support.
- DT bindings.
* asc dlhl60d
- New driver support this range of pressure and temperature sensors.
- DT bindings.
* ltc2496 ADC
- New driver to support this ADC.
- Split the existing LTC2497 driver generic component out and reuse.
- DT bindings.
* parallax ping
- New driver supporting ultrasonic and laser tof distance sensors.
- Bindings for these sensors.
New features
* core
- New char type for read_raw returns, used for thermocouple types.
- Rename read_first_n callback to read. The reasons behind the original
naming are lost to the mists of time.
* ad799x
- Allow pm_ops to disable device completely allowing regulator power down.
* bma180
- Enable basic regulator support.
* dmaengine buffer
- Report platform data alignment requirements via new ABI.
* max31856
- Add option to set mains filter rejection frequency and document
new in_temp_filter_notch_center_frequency ABI.
- Add support for configuring HW averaging (oversampling ratio)
- Add runtime configuration of thermocouple type and document new ABI.
* maxim-thermocouple
- Add read only access to thermocouple type using new ABI, includes
adding more specific compatibles to reflect which variant of the
chip is being used.
* mpu6050
- Provide option to support the PMU9150 in package magnetometer directly
rather than via auxiliary bus.
* stm32_adc
- Add overrun interrupt checks to detect if this happens.
* st_lsm6dsx
- Enable the sensor-hub support for lsm6dsm. Includes various reworks to
allow this.
Cleanups and minor fixes
* Subsystem wide
- Tidy up indentation in Kconfig and fix alphabetical order of AD7091R5.
- Drop linux/gpio.h and linux/of_gpio.h from drivers that don't use them.
* ad7266
- Convert to GPIO descriptors.
* ad7303
- Avoid a dance with checking if the regulator is supplied by just
using the optional request interface.
* ad7887
- Simplify channel specification assignment to enable adding more devices.
* ad7923
- Drop some unused and largely pointless defines of BOB_N==N variety.
- Tidy up checkpatch warnings.
- Add missing of_device_id table.
* adf4350
- Convert to GPIO descriptors.
* ak8975
- Convert to GPIO descriptors.
* ADIS library and drivers
- Expand scope of txrx_lock to cover all state and rename as state_lock
- Add unlocked read / write to allow grouping of consecutive calls under
single lock / unlock.
- Add unlocked check_status, reset to allow grouping under single
lock / unlock.
- Remove remaining uses of core mlock for local state protection.
mlock should never be used directly as it protects tightly defined
core IIO device management state.
* adis16240
- Enforce only supported SPI mode on driver load + add DT binding doc.
* atlas-ph-sensor
- Rename to atlas-sensor given it now covers things beyond ph sensors.
* bma180
- Use local dev variable to tidy up code.
- Use c99 style explicity .member assignment to make driver more readable.
* bmp280
- Drop ACPI support. No evidence this was used and appropriate ID is not
registered.
- Allow ACPI to bind device via PRP0001
* dmaengine buffer
- Use dma_request_chan instead of dma_request_slave_channel_reason as that
ABI is going away.
- Add module info to avoid tainting the kernel.
* hts221
- Avoid magic number defines when only used to fill structure elements
that are self describing.
* lm3533
- Drop a stray semicolon.
* max9611
- Cleanup enum handling to be more resilient to future changes.
* mpu6050
- Delete MPU9150 from supported SPI devices as doesn't provide SPI.
- Select I2C_MUX again after kbuild issue fixed elsewhere.
* stm32-timer
- Drop an unnecessary register update.
* ssp_sensors
- Convert to GPIO descriptors.
* st_sensors
- drop !CONFIG_ACPI defines as ACPI_PTR() will stop them being used
anyway.
- Make default platform data structures __maybe_unsued.
- Fill in some missing kernel-doc function parameters.
* st_lsm6dsx
- white space fixes.
- Mark some constants that aren't always used as __maybe_unused.
- Drop of ID table guards as they just pervent use under ACPI.
- Switch to device properties to allow ACPI usage.
* st_uvis25
- Drop acpi.h include as no ACPI APIs used.
* ti-ads1015
- Drop legacy platform data as no one seems to be using it.
- Use the device property API instead of OF specific.
* ti-ads7950
- typo fix in error message.
-----BEGIN PGP SIGNATURE-----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=8FmM
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.6a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 5.6 cycle
New device support
* ad7091r5 ADC
- New driver with follow up patch adding scale and vref support.
- DT bindings
* ad7923
- Support for ad7908, ad7918 and ad7928 added to driver.
* bma180
- Support the BMA254 accelerometer. Required fairly substantial rework
to allow for small differences between this an existing parts.
* bma400 accelerometer
- New driver with follow up patch for regulator support.
- DT bindings.
* asc dlhl60d
- New driver support this range of pressure and temperature sensors.
- DT bindings.
* ltc2496 ADC
- New driver to support this ADC.
- Split the existing LTC2497 driver generic component out and reuse.
- DT bindings.
* parallax ping
- New driver supporting ultrasonic and laser tof distance sensors.
- Bindings for these sensors.
New features
* core
- New char type for read_raw returns, used for thermocouple types.
- Rename read_first_n callback to read. The reasons behind the original
naming are lost to the mists of time.
* ad799x
- Allow pm_ops to disable device completely allowing regulator power down.
* bma180
- Enable basic regulator support.
* dmaengine buffer
- Report platform data alignment requirements via new ABI.
* max31856
- Add option to set mains filter rejection frequency and document
new in_temp_filter_notch_center_frequency ABI.
- Add support for configuring HW averaging (oversampling ratio)
- Add runtime configuration of thermocouple type and document new ABI.
* maxim-thermocouple
- Add read only access to thermocouple type using new ABI, includes
adding more specific compatibles to reflect which variant of the
chip is being used.
* mpu6050
- Provide option to support the PMU9150 in package magnetometer directly
rather than via auxiliary bus.
* stm32_adc
- Add overrun interrupt checks to detect if this happens.
* st_lsm6dsx
- Enable the sensor-hub support for lsm6dsm. Includes various reworks to
allow this.
Cleanups and minor fixes
* Subsystem wide
- Tidy up indentation in Kconfig and fix alphabetical order of AD7091R5.
- Drop linux/gpio.h and linux/of_gpio.h from drivers that don't use them.
* ad7266
- Convert to GPIO descriptors.
* ad7303
- Avoid a dance with checking if the regulator is supplied by just
using the optional request interface.
* ad7887
- Simplify channel specification assignment to enable adding more devices.
* ad7923
- Drop some unused and largely pointless defines of BOB_N==N variety.
- Tidy up checkpatch warnings.
- Add missing of_device_id table.
* adf4350
- Convert to GPIO descriptors.
* ak8975
- Convert to GPIO descriptors.
* ADIS library and drivers
- Expand scope of txrx_lock to cover all state and rename as state_lock
- Add unlocked read / write to allow grouping of consecutive calls under
single lock / unlock.
- Add unlocked check_status, reset to allow grouping under single
lock / unlock.
- Remove remaining uses of core mlock for local state protection.
mlock should never be used directly as it protects tightly defined
core IIO device management state.
* adis16240
- Enforce only supported SPI mode on driver load + add DT binding doc.
* atlas-ph-sensor
- Rename to atlas-sensor given it now covers things beyond ph sensors.
* bma180
- Use local dev variable to tidy up code.
- Use c99 style explicity .member assignment to make driver more readable.
* bmp280
- Drop ACPI support. No evidence this was used and appropriate ID is not
registered.
- Allow ACPI to bind device via PRP0001
* dmaengine buffer
- Use dma_request_chan instead of dma_request_slave_channel_reason as that
ABI is going away.
- Add module info to avoid tainting the kernel.
* hts221
- Avoid magic number defines when only used to fill structure elements
that are self describing.
* lm3533
- Drop a stray semicolon.
* max9611
- Cleanup enum handling to be more resilient to future changes.
* mpu6050
- Delete MPU9150 from supported SPI devices as doesn't provide SPI.
- Select I2C_MUX again after kbuild issue fixed elsewhere.
* stm32-timer
- Drop an unnecessary register update.
* ssp_sensors
- Convert to GPIO descriptors.
* st_sensors
- drop !CONFIG_ACPI defines as ACPI_PTR() will stop them being used
anyway.
- Make default platform data structures __maybe_unsued.
- Fill in some missing kernel-doc function parameters.
* st_lsm6dsx
- white space fixes.
- Mark some constants that aren't always used as __maybe_unused.
- Drop of ID table guards as they just pervent use under ACPI.
- Switch to device properties to allow ACPI usage.
* st_uvis25
- Drop acpi.h include as no ACPI APIs used.
* ti-ads1015
- Drop legacy platform data as no one seems to be using it.
- Use the device property API instead of OF specific.
* ti-ads7950
- typo fix in error message.
* tag 'iio-for-5.6a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (99 commits)
iio: accel: bma180: BMA254 support
iio: pressure: bmp280: Allow device to be enumerated from ACPI
iio: pressure: bmp280: Drop ACPI support
dt-bindings: iio: adc: convert sd modulator to json-schema
iio: buffer: rename 'read_first_n' callback to 'read'
iio: buffer-dmaengine: Report buffer length requirements
bindings: iio: pressure: Add documentation for dlh driver
dt-bindings: Add asc vendor
iio: pressure: Add driver for DLH pressure sensors
iio: buffer-dmaengine: Add module information
iio: accel: bma180: Use explicit member assignment
iio: accel: bma180: Basic regulator support
iio: accel: bma180: Add dev helper variable
iio: imu: st_lsm6dsx: enable sensor-hub support for lsm6dsm
iio: imu: st_lsm6dsx: rename st_lsm6dsx_shub_read_reg in st_lsm6dsx_shub_read_output
iio: imu: st_lsm6dsx: check if shub_output reg is located in primary page
iio: imu: st_lsm6dsx: check if pull_up is located in primary page
iio: imu: st_lsm6dsx: check if master_enable is located in primary page
iio: imu: st_lsm6dsx: export max num of slave devices in st_lsm6dsx_shub_settings
iio: light: remove unneeded semicolon
...
This header file now only includes the cros_ec_dev struct, however, is the
'include/linux/platform_data/cros_ec_proto.h' who contains the definition of
all the Chrome OS EC related structs. There is no reason to have a
separate include for this struct so move to the place where other
structs are defined. That way, we can remove the include itself, but also
simplify the common pattern
#include <linux/mfd/cros_ec.h>
#include <linux/platform_data/cros_ec_proto.h>
for a single include
#include <linux/platform_data/cros_ec_proto.h>
The changes to remove the cros_ec.h include were generated with the
following shell script:
git grep -l "<linux/mfd/cros_ec.h>" | xargs sed -i '/<linux\/mfd\/cros_ec.h>/d'
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
There is no evidence that the driver supports or needs ACPI APIs.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver includes <linux/gpio.h> and <linux/of_gpio.h> yet
fails to use symbols from any of the include files, so drop
these includes.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver include <linux/gpio.h> yet does not use any
of the symbols from the header, so drop the include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* CrOS EC / MFD / IIO
- Contains tag-ib-chrome-mfd-iio-input-5.5, which is the first part of a
series from Gwendal to refactor sensor code between MFD, CrOS EC, iio
and input in order to add a new sensorhub driver and FIFO processing
* Wilco EC:
- Add support for Dell's USB PowerShare policy control, keyboard
backlight LED driver, and a new test_event file.
- Fixes use after free in wilco_ec's telemetry driver.
* Misc:
- bugfix in cros_usbpd_logger (missing destroy workqueue).
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQCtZK6p/AktxXfkOlzbaomhzOwwgUCXeaqtwAKCRBzbaomhzOw
wilIAQCQ3/dpAwg2skKYYf3RBLDJeDLA1id7rNSgMOXc2aKyTAD/fCQtNhwj+Hal
W//04WWngTCQF5fkE9OCJrDwbm5eRwc=
=uOGe
-----END PGP SIGNATURE-----
Merge tag 'tag-chrome-platform-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform changes from Benson Leung:
"CrOS EC / MFD / IIO:
- Contains tag-ib-chrome-mfd-iio-input-5.5, which is the first part
of a series from Gwendal to refactor sensor code between MFD, CrOS
EC, iio and input in order to add a new sensorhub driver and FIFO
processing
Wilco EC:
- Add support for Dell's USB PowerShare policy control, keyboard
backlight LED driver, and a new test_event file.
- Fixes use after free in wilco_ec's telemetry driver.
Misc:
- bugfix in cros_usbpd_logger (missing destroy workqueue)"
* tag 'tag-chrome-platform-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: wilco_ec: fix use after free issue
platform/chrome: cros_ec: Add Kconfig default for cros-ec-sensorhub
Revert "Input: cros_ec_keyb: mask out extra flags in event_type"
Revert "Input: cros_ec_keyb - add back missing mask for event_type"
platform/chrome: cros_ec: handle MKBP more events flag
platform/chrome: cros_ec: Do not attempt to register a non-positive IRQ number
platform/chrome: cros-ec: Record event timestamp in the hard irq
mfd / platform / iio: cros_ec: Register sensor through sensorhub
iio / platform: cros_ec: Add cros-ec-sensorhub driver
mfd / platform: cros_ec: Add sensor_count and make check_features public
platform/chrome: cros_ec: Put docs with the code
platform/chrome: cros_usbpd_logger: add missed destroy_workqueue in remove
platform/chrome: cros_ec: Fix Kconfig indentation
platform/chrome: wilco_ec: Add keyboard backlight LED support
platform/chrome: wilco_ec: Add charging config driver
platform/chrome: wilco_ec: Add Dell's USB PowerShare Policy control
platform/chrome: wilco_ec: Add debugfs test_event file
Remove the duplicated code in MFD, since MFD just registers cros-ec-sensorhub
if at least one sensor is present.
Change IIO cros-ec driver to get the pointer to the cros-ec-dev through
cros-ec-sensorhub.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
veml6030 is an ambient light sensor from Vishay semiconductors.
It has 16-bit resolution, supports both ambient light measurement
and white channel which is more responsive to wider wavelength
spectrum. It has flexible power saving, integration time and
gain options. Communication with host is over I2C.
Signed-off-by: Rishi Gupta <gupt21@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add initial support for Analog Devices ADUX1020 Photometric sensor.
Only proximity mode has been enabled for now.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Third version with the adis rework set dropped as better to just have
a fresh version of that at some future date.
The usual mixed backs of new device support being added to drivers,
long term reworks continuing and little per driver cleanups and
features.
Also a few trivial counter subsystem tidy ups on behalf of William.
Core new feature
* Device label support. A long requested feature no one got around to
implementing before. Allows DT based provision of a 'label' that
identifies a device uniquely within a system. This differs from existing
'name' which is meant to be the part number.
New device support
* ingenic-adc
- Support for the JZ4770 SoC ADC including bindings.
* inv_mpu6050
- Add support for magnetometer in MPU925x parts.
Fiddly to do as this is actually a separate device sitting inside the
package, but with the master device being able to schedule reads etc.
Will only run if the auxiliary bus is not in use for any other devices.
Features
* ad7192
- Userspace calibration controls to do zero and full scale.
* st_lsm6dsx
- Enable latched interrupts by default for sensors events with related clear.
- Motion events and related wakeup source. This needed quite a bit of
refactoring as well.
Cleanups and minor features
* ad7192
- sysfs ABI docs
* ad7949
- Remove code to readback configuration word as driver never actually enabled
it.
- Fix incorrect xfer length. Not actually known to cause problems other
than wasted bus usage.
* adis16080
- Replace core mlock usage with local lock with more appropriate scope.
* adis16130
- Remove pointless mlock usage.
* adis16240
- Remove include of gpio.h as no gpio usage.
* atlas-ph-sensor
- Improve logical ordering of buffer predisable / postenable functions.
This is part of a longer term rework Alexandru is driving towards.
* bh1750
- Fix up a static compiler warning and make the code more readable.
- yaml conversion of binding + MAINTAINERS entry.
* bmp280
- Drop a stray newline.
* cm36651
- Drop a redundant assignment
* itg3200
- Alignment cleanup.
* max31856
- Add missing of_node and parent references, useful to identify the device.
* sc27xx_adc
- Use devm_hwspin_lock_request_specific rather than local rolled version.
* stm32-lptimer counter
- kernel-doc warning.
* stm32-timer counter
- kernel-doc warning.
- Alignment cleanup.
* sx9500
- Improve logical ordering of buffer predisable / postenable functions.
This is part of a longer term rework Alexandru is driving towards.
* tcs3414
- Improve logical ordering of buffer predisable / postenable functions.
This is part of a longer term rework Alexandru is driving towards.
-----BEGIN PGP SIGNATURE-----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=nIWU
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.5a-take3' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of IIO new device support, cleanups and features for the 5.5 cycle
Third version with the adis rework set dropped as better to just have
a fresh version of that at some future date.
The usual mixed backs of new device support being added to drivers,
long term reworks continuing and little per driver cleanups and
features.
Also a few trivial counter subsystem tidy ups on behalf of William.
Core new feature
* Device label support. A long requested feature no one got around to
implementing before. Allows DT based provision of a 'label' that
identifies a device uniquely within a system. This differs from existing
'name' which is meant to be the part number.
New device support
* ingenic-adc
- Support for the JZ4770 SoC ADC including bindings.
* inv_mpu6050
- Add support for magnetometer in MPU925x parts.
Fiddly to do as this is actually a separate device sitting inside the
package, but with the master device being able to schedule reads etc.
Will only run if the auxiliary bus is not in use for any other devices.
Features
* ad7192
- Userspace calibration controls to do zero and full scale.
* st_lsm6dsx
- Enable latched interrupts by default for sensors events with related clear.
- Motion events and related wakeup source. This needed quite a bit of
refactoring as well.
Cleanups and minor features
* ad7192
- sysfs ABI docs
* ad7949
- Remove code to readback configuration word as driver never actually enabled
it.
- Fix incorrect xfer length. Not actually known to cause problems other
than wasted bus usage.
* adis16080
- Replace core mlock usage with local lock with more appropriate scope.
* adis16130
- Remove pointless mlock usage.
* adis16240
- Remove include of gpio.h as no gpio usage.
* atlas-ph-sensor
- Improve logical ordering of buffer predisable / postenable functions.
This is part of a longer term rework Alexandru is driving towards.
* bh1750
- Fix up a static compiler warning and make the code more readable.
- yaml conversion of binding + MAINTAINERS entry.
* bmp280
- Drop a stray newline.
* cm36651
- Drop a redundant assignment
* itg3200
- Alignment cleanup.
* max31856
- Add missing of_node and parent references, useful to identify the device.
* sc27xx_adc
- Use devm_hwspin_lock_request_specific rather than local rolled version.
* stm32-lptimer counter
- kernel-doc warning.
* stm32-timer counter
- kernel-doc warning.
- Alignment cleanup.
* sx9500
- Improve logical ordering of buffer predisable / postenable functions.
This is part of a longer term rework Alexandru is driving towards.
* tcs3414
- Improve logical ordering of buffer predisable / postenable functions.
This is part of a longer term rework Alexandru is driving towards.
* tag 'iio-for-5.5a-take3' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (41 commits)
iio: pressure: bmp280: remove stray newline
iio: adc: sc27xx: Use devm_hwspin_lock_request_specific() to simplify code
iio: chemical: atlas-ph-sensor: fix iio_triggered_buffer_predisable() position
iio: gyro: clean up indentation issue
counter: stm32: clean up indentation issue
iio: proximity: sx9500: fix iio_triggered_buffer_{predisable,postenable} positions
iio: core: Add optional symbolic label to device attributes
dt-binding: iio: Add optional label property
iio: gyro: adis16080: replace mlock with own lock
counter: stm32-lptimer-cnt: fix a kernel-doc warning
counter: stm32-timer-cnt: fix a kernel-doc warning
iio: gyro: adis16130: remove mlock usage
MAINTAINERS: add entry for ROHM BH1750 driver
dt-bindings: iio: light: bh1750: convert bindings to yaml
iio: imu: st_lsm6dsx: add motion report function and call from interrupt
iio: imu: st_lsm6dsx: always enter interrupt thread
iio: imu: st_lsm6dsx: add wakeup-source option
iio: imu: st_lsm6dsx: add motion events
iio: imu: st_lsm6dsx: move interrupt thread to core
iio: imu: inv_mpu6050: add fifo support for magnetometer data
...
* adis16400
- Make sure to free memory on a few failure paths.
* adxl372
- Fix wrong fifo depth
- Fix wrong indexing of data from the fifo.
- Perform a reset at startup to avoid a problem with inconsistent state.
* axp288
- This is a fix for a fix. The original fix made sure we kept the
configuration from some firmwares to preserve a bias current.
Unfortunately it appears the previous behaviour was working around
a buggy firmware by overwriting the wrong value it had. Hence
a regression was seen.
* bmc150
- Fix the centre temperature. This was due to an error in one of the
datasheets.
* hx711
- Fix an issue where a badly timed interrupt could lead to a control
line being high long enough to put the device into a low power state.
* meson_sar_adc
- Fix a case where the irq was enabled before everything it uses was
allocated.
* st_lsm6dsx
- Ensure we don't set the sensor sensitivity to 0 as it will force
all readings to 0.
- Fix a wait time for the slave i2c controller when the accelerometer
is not enabled.
* stm32-adc
- Precursor for fix. Move a set of register definitions to a header.
- Fix a race when several ADCs are in use with some using interrupts
to control the dataflow and some using DMA.
* vcnl4000
- Fix a garbage of_match_table in which a string was passed instead
of the intended enum.
-----BEGIN PGP SIGNATURE-----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=s9EA
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-5.4a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 5.4 cycle.
* adis16400
- Make sure to free memory on a few failure paths.
* adxl372
- Fix wrong fifo depth
- Fix wrong indexing of data from the fifo.
- Perform a reset at startup to avoid a problem with inconsistent state.
* axp288
- This is a fix for a fix. The original fix made sure we kept the
configuration from some firmwares to preserve a bias current.
Unfortunately it appears the previous behaviour was working around
a buggy firmware by overwriting the wrong value it had. Hence
a regression was seen.
* bmc150
- Fix the centre temperature. This was due to an error in one of the
datasheets.
* hx711
- Fix an issue where a badly timed interrupt could lead to a control
line being high long enough to put the device into a low power state.
* meson_sar_adc
- Fix a case where the irq was enabled before everything it uses was
allocated.
* st_lsm6dsx
- Ensure we don't set the sensor sensitivity to 0 as it will force
all readings to 0.
- Fix a wait time for the slave i2c controller when the accelerometer
is not enabled.
* stm32-adc
- Precursor for fix. Move a set of register definitions to a header.
- Fix a race when several ADCs are in use with some using interrupts
to control the dataflow and some using DMA.
* vcnl4000
- Fix a garbage of_match_table in which a string was passed instead
of the intended enum.
* tag 'iio-fixes-for-5.4a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: Fix an undefied reference error in noa1305_probe
iio: light: opt3001: fix mutex unlock race
iio: adc: ad799x: fix probe error handling
iio: light: add missing vcnl4040 of_compatible
iio: light: fix vcnl4000 devicetree hooks
iio: imu: st_lsm6dsx: fix waitime for st_lsm6dsx i2c controller
iio: adc: axp288: Override TS pin bias current for some models
iio: imu: adis16400: fix memory leak
iio: imu: adis16400: release allocated memory on failure
iio: adc: stm32-adc: fix a race when using several adcs with dma and irq
iio: adc: stm32-adc: move registers definitions
iio: accel: adxl372: Perform a reset at start up
iio: accel: adxl372: Fix push to buffers lost samples
iio: accel: adxl372: Fix/remove limitation for FIFO samples
iio: adc: hx711: fix bug in sampling of data
iio: fix center temperature of bmc150-accel-core
iio: imu: st_lsm6dsx: forbid 0 sensor sensitivity
iio: adc: meson_saradc: Fix memory allocation order
I hit the following error when compile the kernel.
drivers/iio/light/noa1305.o: In function `noa1305_probe':
noa1305.c:(.text+0x65): undefined reference to `__devm_regmap_init_i2c'
make: *** [vmlinux] Error 1
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When an end-of-conversion interrupt is received after performing a
single-shot reading of the light sensor, the driver was waking up the
result ready queue before checking opt->ok_to_ignore_lock to determine
if it should unlock the mutex. The problem occurred in the case where
the other thread woke up and changed the value of opt->ok_to_ignore_lock
to false prior to the interrupt thread performing its read of the
variable. In this case, the mutex would be unlocked twice.
Signed-off-by: David Frey <dpfrey@gmail.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
Fixes: 94a9b7b180 ("iio: light: add support for TI's opt3001 light sensor")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit 5a441aade5 ("iio: light: vcnl4000 add support for the VCNL4040
proximity and light sensor") added the support for the vcnl4040 but
forgot to add the of_compatible. Fix this by adding it now.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Fixes: 5a441aade5 ("iio: light: vcnl4000 add support for the VCNL4040 proximity and light sensor")
Reviewed-by: Angus Ainslie (Purism) angus@akkea.ca
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since commit ebd457d559 ("iio: light: vcnl4000 add devicetree hooks")
the of_match_table is supported but the data shouldn't be a string.
Instead it shall be one of 'enum vcnl4000_device_ids'. Also the matching
logic for the vcnl4020 was wrong. Since the data retrieve mechanism is
still based on the i2c_device_id no failures did appeared till now.
Fixes: ebd457d559 ("iio: light: vcnl4000 add devicetree hooks")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Angus Ainslie (Purism) angus@akkea.ca
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The iio_triggered_buffer_{predisable,postenable} functions attach/detach
the poll functions.
For the predisable hook, the disable code should occur before detaching
the poll func, and for the postenable hook, the poll func should be
attached before the enable code.
The driver was slightly reworked. The preenable hook was moved to the
postenable, to add some symmetry to the postenable/predisable part.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Separate the declaration of struct bh1750_chip_info from definition
of bh1750_chip_info_tbl[] in a single statement as it makes the code
hard to read, and with the extra newline it makes it look as if the
bh1750_chip_info_tbl[] had no explicit type.
This change also resolves the following compiler warning about the
unusual position of the static keyword that can be seen when building
with warnings enabled (W=1):
drivers/iio/light/bh1750.c:64:1: warning:
‘static’ is not at beginning of declaration [-Wold-style-declaration]
Related to commit 3a11fbb037 ("iio: light: add support for ROHM
BH1710/BH1715/BH1721/BH1750/BH1751 ambient light sensors").
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Variable ret is being assigned a value that is never read and
is being re-assigned a little later on. The assignment is redundant
and hence can be removed.
Addresses-Coverity: ("Ununsed value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is a bit of mess between cros-ec mfd includes and platform
includes. For example, we have a linux/mfd/cros_ec.h include that
exports the interface implemented in platform/chrome/cros_ec_proto.c. Or
we have a linux/mfd/cros_ec_commands.h file that is non related to the
multifunction device (in the sense that is not exporting any function of
the mfd device). This causes crossed includes between mfd and
platform/chrome subsystems and makes the code difficult to read, apart
from creating 'curious' situations where a platform/chrome driver includes
a linux/mfd/cros_ec.h file just to get the exported functions that are
implemented in another platform/chrome driver.
In order to have a better separation on what the cros-ec multifunction
driver does and what the cros-ec core provides move and rework the
affected includes doing:
- Move cros_ec_commands.h to include/linux/platform_data/cros_ec_commands.h
- Get rid of the parts that are implemented in the platform/chrome/cros_ec_proto.c
driver from include/linux/mfd/cros_ec.h to a new file
include/linux/platform_data/cros_ec_proto.h
- Update all the drivers with the new includes, so
- Drivers that only need to know about the protocol include
- linux/platform_data/cros_ec_proto.h
- linux/platform_data/cros_ec_commands.h
- Drivers that need to know about the cros-ec mfd device also include
- linux/mfd/cros_ec.h
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Series changes: 3
- Fix dereferencing pointer to incomplete type 'struct cros_ec_dev' (lkp)
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This got caught by the implicit fall through detection but is
a bug rather than missing marking.
Reported-by: 0-DAY kernel test infrastructure
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fixes: 741172d18e ("iio: light: noa1305: Add support for NOA1305")
Link: https://lore.kernel.org/r/20190813133851.14345-1-Jonathan.Cameron@huawei.com
Cc: Gustavo Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver adds the initial support for the ON Semiconductor
NOA1305 Ambient Light Sensor.
Originally written by Sergei Miroshnichenko. Found here:
196d6cf897
Signed-off-by: Sergei M <fizik1@yandex.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use regulator_bulk_() APIs to shrink driver size.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Brian Masney <masneyb@onstation.org>
Tested-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use devm_iio_device_register, which removes the tsl2772_remove
function.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Brian Masney <masneyb@onstation.org>
Tested-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use devm_add_action_or_reset to call tsl2772_chip_off
when the device is removed.
This also fixes the issue that the chip is turned off
before the device is unregistered.
Not marked for stable as fairly hard to hit the bug and
this is in the middle of a set making other cleanups
to the driver. Hence will probably need explicit backporting.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Fixes: c06c4d7935 ("staging: iio: tsl2x7x/tsl2772: move out of staging")
Reviewed-by: Brian Masney <masneyb@onstation.org>
Tested-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use devm_add_action_or_reset to remove the call to
tsl2772_disable_regulators_action to simplify the error path.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Brian Masney <masneyb@onstation.org>
Tested-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use device-managed APIs to simplify the code.
The remove functions are redundant now and can
be deleted.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use device-managed APIs to simplify the code.
The remove functions are redundant now and can
be deleted.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Embedded controller return minimum and maximum frequencies, unfortunately
we have no way to know the step for all available frequencies.
Even if not complete, we can return a list of known values using the
standard read_avail callback (IIO_CHAN_INFO_SAMP_FREQ) to provide them to
userland.
Now cros_ec_* sensors provides frequencies values in sysfs like this:
"0 min max". 0 is always true to disable the sensor.
Default frequencies are provided for earlier protocol.
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
[rebased on top of iio/testing and solved conflicts]
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Due to an API misread, error code can be different for -EIO when reading
a sysfs entry. Return the error reported by the cros_ec stack.
Check the proper error message (protocol error, not supported) is
reported when there is an error returned by the EC stack.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add calibration scale support to accel, gyro and magnetometer.
Check on eve with current firmware, check reading calibscale returns 1.0,
check with newer firmware values are applied.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
s/ADPS9960/APDS9960/
(P and D switched)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add device tree support for the stk33xx family of ambient light sensors.
Tested-by: Martijn Braam <martijn@brixit.nl>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
A few bits for the counters subsystem mixed in here as well.
There are some late breaking fixes as well, which aren't so urgent
they can't wait for the merge window.
New Device Support
* adf4371
- New driver + bindings.
- Support the adf4372 PLL. Mostly ID and bindings.
* ad8366 (note includes rework of driver needed to allow support for these).
- Support the ADL5240 variable gain amplifier (VGA).
- Support the ADA4961 digital gain amplifier (DGA).
* dps310
- New driver, in several parts from different authors for this temp
and pressure sensor.
- Includes errata workaround for a temperature reading issue.
* stk3310
- Support the stk3335, mostly ID.
Features and cleanups
* core
- drop error handling on debugfs registration.
- harden by making sure we don't overrun iio_chan_info_postfix.
* docs
- convert remaining docs to rst. At somepoint we'll fit these few
into the main IIO docs.
- improve sampling_frequency_available docs but explaining the
range form.
* ad_sigma_delta
- Drop a pointless goto.
* ad2s1210
- Drop pointless platform data null check seeing as we don't actually
use platform data anymore.
* ad7124
- Relax limitation on channel numbers to allow pseudo different channels.
- Support control of whether the input is buffered via DT.
- Use dynamic allocation for channel configuration to make it easier
to support new devices.
- YAML binding conversion.
* ad7150
- Comment tidy up.
- Consistent and simple if (ret) handling of i2c errors.
- FIELD_GET and GENMASK.
- Ternary rather than !!(condition) for readability.
- Use macros to avoid repetition of channel definitions.
* ad7606
- Add software channel config (rather that pin controlled)
- Refactor to simplify addition of new part in future.
* ad7746
- of_deivce_id table.
* ad7780
- MAINTAINERS entry
- YAML DT bindings.
* ad8366
- Stop using core mlock in favour of well scoped local lock.
- SPDX + copyright date update.
* ad9834
- of_device_id table
* adf4371
- Add support for output stage muting before lock on has occured.
* adis library
- MAINTAINERS entry to reflect that this now Alexandru's problem ;)
* adis162xx:
- Fix a slightly incorrect set of comments and print statements on
minimum supported voltage.
* adis16203
- of_device_id table.
* adis16240
- Add of_device_id table (in two parts as first patch only used it for
MODULE_DEVICE_TABLE.)
* adt7316-spi
- of_device_id table
* adxl372
- YAML DT binding conversion.
- Cleanup use of buffer callback functions (precursor to core rework).
* bh1710
- Simplify getting the i2c adapter from the client.
* dht11
- Mote to newer GPIO consumer interface.
* kxcjk-1013.c
- Add binding for sensor in display of some ultrabooks after userspace
tools updated for it not be a problem to report two similar sensors.
* imx7d
- drop unused variables.
- white space
- define instead of variable for clock frequency that is fixed.
- drop pointless error message.
* messon_saradc
- SPDX
* sps30
- MAINTAINERS entry
- YAML binding conversion.
* st_accel
- Tidy up ordering in various buffer related callbacks. This is
part of a long running effort to simplify the core code.
* stm32-dfsdm:
- Manage the resolution cleanly in triggerd modes.
- Add fast mode support which allows more flexible filter choices.
- Add a comment on the reason for a 16 bit record when technically
not 'required'.
* st_lsm6dsx
- Embed device name in the sensor_settings struct as i3c doesn't
have a convenient name field to use for this.
* xilinx-adc
- Relax constraints on supported platforms to reflect that this
can used with FPGAs on PCIe cards and hence many architectures.
* counters/ftm-quaddec
- Fix some formatting io MODULE_AUTHOR
- MAINTAINERS entry
Fixes
* tools
- fix incorrect handling of 32 bit channels.
* sca3000
- Potential endian bug that is unlikely to bite anyone (be64 host
seems unlikely for this old part).
* stm32-adc
- Add vdda-supply. On some boards it needs to be turned on to supply
the ADC. DT bindings included.
* stm32-dfsdm
- Fix output resolution to work with filter orders other than 3.
- Fix output datatype as it's signed and previously claimed not to be.
-----BEGIN PGP SIGNATURE-----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=a3vh
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.3b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO device support, features, cleanups and minor fixes for 5.3.
A few bits for the counters subsystem mixed in here as well.
There are some late breaking fixes as well, which aren't so urgent
they can't wait for the merge window.
New Device Support
* adf4371
- New driver + bindings.
- Support the adf4372 PLL. Mostly ID and bindings.
* ad8366 (note includes rework of driver needed to allow support for these).
- Support the ADL5240 variable gain amplifier (VGA).
- Support the ADA4961 digital gain amplifier (DGA).
* dps310
- New driver, in several parts from different authors for this temp
and pressure sensor.
- Includes errata workaround for a temperature reading issue.
* stk3310
- Support the stk3335, mostly ID.
Features and cleanups
* core
- drop error handling on debugfs registration.
- harden by making sure we don't overrun iio_chan_info_postfix.
* docs
- convert remaining docs to rst. At somepoint we'll fit these few
into the main IIO docs.
- improve sampling_frequency_available docs but explaining the
range form.
* ad_sigma_delta
- Drop a pointless goto.
* ad2s1210
- Drop pointless platform data null check seeing as we don't actually
use platform data anymore.
* ad7124
- Relax limitation on channel numbers to allow pseudo different channels.
- Support control of whether the input is buffered via DT.
- Use dynamic allocation for channel configuration to make it easier
to support new devices.
- YAML binding conversion.
* ad7150
- Comment tidy up.
- Consistent and simple if (ret) handling of i2c errors.
- FIELD_GET and GENMASK.
- Ternary rather than !!(condition) for readability.
- Use macros to avoid repetition of channel definitions.
* ad7606
- Add software channel config (rather that pin controlled)
- Refactor to simplify addition of new part in future.
* ad7746
- of_deivce_id table.
* ad7780
- MAINTAINERS entry
- YAML DT bindings.
* ad8366
- Stop using core mlock in favour of well scoped local lock.
- SPDX + copyright date update.
* ad9834
- of_device_id table
* adf4371
- Add support for output stage muting before lock on has occured.
* adis library
- MAINTAINERS entry to reflect that this now Alexandru's problem ;)
* adis162xx:
- Fix a slightly incorrect set of comments and print statements on
minimum supported voltage.
* adis16203
- of_device_id table.
* adis16240
- Add of_device_id table (in two parts as first patch only used it for
MODULE_DEVICE_TABLE.)
* adt7316-spi
- of_device_id table
* adxl372
- YAML DT binding conversion.
- Cleanup use of buffer callback functions (precursor to core rework).
* bh1710
- Simplify getting the i2c adapter from the client.
* dht11
- Mote to newer GPIO consumer interface.
* kxcjk-1013.c
- Add binding for sensor in display of some ultrabooks after userspace
tools updated for it not be a problem to report two similar sensors.
* imx7d
- drop unused variables.
- white space
- define instead of variable for clock frequency that is fixed.
- drop pointless error message.
* messon_saradc
- SPDX
* sps30
- MAINTAINERS entry
- YAML binding conversion.
* st_accel
- Tidy up ordering in various buffer related callbacks. This is
part of a long running effort to simplify the core code.
* stm32-dfsdm:
- Manage the resolution cleanly in triggerd modes.
- Add fast mode support which allows more flexible filter choices.
- Add a comment on the reason for a 16 bit record when technically
not 'required'.
* st_lsm6dsx
- Embed device name in the sensor_settings struct as i3c doesn't
have a convenient name field to use for this.
* xilinx-adc
- Relax constraints on supported platforms to reflect that this
can used with FPGAs on PCIe cards and hence many architectures.
* counters/ftm-quaddec
- Fix some formatting io MODULE_AUTHOR
- MAINTAINERS entry
Fixes
* tools
- fix incorrect handling of 32 bit channels.
* sca3000
- Potential endian bug that is unlikely to bite anyone (be64 host
seems unlikely for this old part).
* stm32-adc
- Add vdda-supply. On some boards it needs to be turned on to supply
the ADC. DT bindings included.
* stm32-dfsdm
- Fix output resolution to work with filter orders other than 3.
- Fix output datatype as it's signed and previously claimed not to be.
* tag 'iio-for-5.3b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (68 commits)
iio: iio-utils: Fix possible incorrect mask calculation
iio: frequency: adf4371: Add support for output stage mute
dt-bindings: iio: frequency: Add ADF4372 PLL documentation
iio: frequency: adf4371: Add support for ADF4372 PLL
dt-bindings: iio: adc: Add buffered input property
Convert AD7124 bindings documentation to YAML format.
iio: adc: ad7124: Shift to dynamic allocation for channel configuration
iio: adc: ad7124: Add buffered input support
iio: adc: ad7124: Remove input number limitation
MAINTAINERS: add ADIS IMU driver library entry
iio: adis162xx: fix low-power docs & reports
counter/ftm-quaddec: Add missing '>' in MODULE_AUTHOR
iio: core: no need to check return value of debugfs_create functions
docs: iio: convert to ReST
iio: adc: stm32-adc: add missing vdda-supply
dt-bindings: iio: adc: stm32: add missing vdda supply
iio: adc: stm32-dfsdm: add comment for 16 bits record
iio: adc: stm32-dfsdm: add fast mode support
iio: adc: stm32-dfsdm: manage data resolution in trigger mode
iio: adc: stm32-dfsdm: fix data type
...
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope it will be useful but without any warranty
without even the implied warranty of merchantability or fitness for
a particular purpose see the gnu general public license for more
details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081205.379537898@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stk3335 light/proximity sensor is similar to the stk3310 and stk3311
sensors and works with the stk3310 driver.
Signed-off-by: Martijn Braam <martijn@brixit.nl>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We have a dedicated pointer for that, so use it. Much easier to read and
less computation involved.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 of
the license as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 2 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531081038.470437358@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin st fifth floor boston ma 02110
1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 246 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.674189849@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin st fifth floor boston ma 02110
1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 111 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.567572064@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this file is subject to the terms and conditions of version 2 of the
gnu general public license see the file copying in the main
directory of this archive for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 55 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.108941081@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
it and or modify it under the terms of the gnu general public
license version 2 as published by the free software foundation this
program is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 11 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000434.249870634@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 263 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 228 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.107155473@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
licensed under the gpl 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 135 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170026.071193225@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The VCNL4040 is almost identical to the VCNL4200 as far as register
layout goes but just need to check a different ID register location.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The VCNL4200 datasheet says that word read and writes should be used
to access the registers.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Tested-by: Tomas Novotny <tomas@novotny.cz>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Adopt the SPDX license identifier headers to ease license compliance
management. Also fix MODULE_LICENSE for cros_ec_accel_legacy to match
the SPDX and boiler plate license.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The cros_ec sensors drivers do not call any sysfs functions
or use any sysfs defines, and thus do not need to include
linux/sysfs.h. Also, some cros_ec drivers include linux/delay.h
and is not used.
Signed-off-by: Guenter Roeck <groeck@chromium.org>
[remove linux/delay.h]
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Formatting of Kconfig files doesn't look so pretty, so just
take damp cloth and clean it up.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The MAX44009 is a low-power ambient light sensor from Maxim
Integrated. It differs from the MAX44000 in that it doesn't have
proximity sensing and that it requires far less current (1 micro-amp
vs 5 micro-amps). The register mapping and feature set between the
two are different enough to require a new driver for the MAX44009.
Developed and tested with a BeagleBone Black and UDOO Neo (i.MX6SX)
Supported features:
* Reading lux (processed value)
* Rising and falling illuminance threshold
events
* Configuring integration time
https://datasheets.maximintegrated.com/en/ds/MAX44009.pdf
Signed-off-by: Robert Eshleman <bobbyeshleman@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The light sensor's power supply could be controllable by regulator
on some platforms, such as i.MX6Q-SABRESD board, the light sensor
isl29023's power supply is controlled by a GPIO fixed regulator,
need to make sure the regulator is enabled before any operation of
sensor, this patch adds vcc regulator operation support.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Along with the headline feature of 5 new drivers, we have the
substantial addition of auxilliary sensor support on the lsm6sdx
parts for ST. There has also been a good set of staging cleanup
in this period with more underway.
An ever increasing number of devices supported with just a new
ID which is a good sign that at least some manufacturers are
continuing to stabilise their interfaces.
New device support,
* ad7124
- New driver supporting Analog Devices' ad7124-4 and ad7124-8 parts
with the inevitable DT binding.
* ad7949
- New driver supporting Analog Devices' ad7949, AD7682 and AD7689 ADCs.
* rm3100
- New driver supporting PNIs RM3100 magnometer with bindings and
vendor prefix.
* ti-dac7311
- New driver supporting DAC7311, DAC6311 and DAC5311 TI DACs, with
DT bindings.
* vcnl5035
- New driver supporting the light sensor part of the VCNL4035, with
DT bindings
Features,
* bindings
- Add a generic ADC channel binding as we keep reinventing this
wheel.
* adc128s052
- Add IDs for additional pin compatible parts.
- Add APCI ID seen on E3940 UP squared boards.
* ad_sigma_delta
- Allow for custom data register overiding default.
* kxcjk1013
- Add KIOX0009 ACPI ID as seen on the Acer One 10.
* lsm6dsx
- Rework leading to...
- External sensor support using the built in I2C master.
- Initial support for a slave lis2mdl magnetometer.
* meson-saradc
- Add temperature sensor support and bindings.
* st_magn
- New ID for lsm9dsl_magn with bindings
- New ID for lis3de accelerometer
* tpl0102
- Add supprot for IIO_AVAIL_RANGE to report the range available
from this device to userspace and in kernel users.
Cleanups and minor fixes
* tools
- Allow outside specification of CFLAGS
* ad2s90
- Handle and spi_read error.
- Handle spi_setup failure
- Drop a pointless assignment.
- Prevent a potentail race by moving device registration to after
all other setup.
- Add missing scale attribute.
- Add a sanity check on channel type before trying to read it.
* ad2s1210
- Move to modern gpio descriptors.
- Drop a gpioin flag which made no sense as far as we can tell.
- Add dt table (bindings doc to follow when this is ready for
moving out of staging).
* ad5933
- Drop camel-case naming of ext_clk_hz.
- White space fixes.
* ad7150
- Local variable to shorten overly long line.
- Alignment and line break fixes.
* ad7280a
- Handle an error path that was previously ignored.
- Use crc8.h to build the crc table replacing custom code.
- Avoid unecessary cast.
- Power down the device if an error happens in probe
- Use devm routines to simplify probe and remove.
* ad7606
- Alignment fixes.
* ad7780
- This worked as long as by coincidence an uninitialized value
was 0. Lets not rely on that.
- Ensure gain update is only used with the ad778x chips that
actually support it.
- Tidy up pattern mask generation.
- Read regulator when scale is requested (which should be infrequent)
as it might have changed from initialization.
* ad7816
- Move to modern gpio descriptors
- Don't use a busy_pin for ad7818 as there isn't one.
- Ensure RD/WR and CONVST pins are outputs (previously they
were brought up as inputs which doesn't seem to make any sense)
- DT id table.
* adc128s052
- SPDX
* adt7316
- Alignment fix.
- Fix data reading. When using I2C the driver never actually
used the value read. This has been broken a very long time
hence no rush to fix it now + the driver is undergoing a lot
of cleanup.
- Sanity check that the i2c read didn't fail to actually read
anything.
* dpot-dac
- Mark a switch full through with slightly different text so that
gcc doesn't warn on it.
* gyro-adc
- Fix a wrong file in the MAINTAINERS entry and add binding doc to the
listed files.
* ina2xx
- Add some early returns to clarify error paths in switch.
* lsm6dsx
- MAINTAINERS entry.
* max11100
- SPDX
* max9611
- SPDX
* mcp4131
- use of_device_get_match_data in preference to spi_get_device_id
approach.
* rcar-adc
- SPDX
* sc27xx
- Add ADC conversion timeout support to avoid possible fault.
* ssp_sensors
- Don't free managed resources manually.
* st-magn
- Add a comment to avoid future confusion over when to use -magn
postfix (on multi chip in package parts)
- Add BDU register for LIS3MDL where it seems to have been missed.
* st-sensors
- Minor spelling, grammar etc fixes.
* tpl0102
- Use a pointer rather than an index of an array to improve conciseness.
-----BEGIN PGP SIGNATURE-----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=78Y3
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.21a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-testing
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 4.21 cycle
Along with the headline feature of 5 new drivers, we have the
substantial addition of auxilliary sensor support on the lsm6sdx
parts for ST. There has also been a good set of staging cleanup
in this period with more underway.
An ever increasing number of devices supported with just a new
ID which is a good sign that at least some manufacturers are
continuing to stabilise their interfaces.
New device support,
* ad7124
- New driver supporting Analog Devices' ad7124-4 and ad7124-8 parts
with the inevitable DT binding.
* ad7949
- New driver supporting Analog Devices' ad7949, AD7682 and AD7689 ADCs.
* rm3100
- New driver supporting PNIs RM3100 magnometer with bindings and
vendor prefix.
* ti-dac7311
- New driver supporting DAC7311, DAC6311 and DAC5311 TI DACs, with
DT bindings.
* vcnl5035
- New driver supporting the light sensor part of the VCNL4035, with
DT bindings
Features,
* bindings
- Add a generic ADC channel binding as we keep reinventing this
wheel.
* adc128s052
- Add IDs for additional pin compatible parts.
- Add APCI ID seen on E3940 UP squared boards.
* ad_sigma_delta
- Allow for custom data register overiding default.
* kxcjk1013
- Add KIOX0009 ACPI ID as seen on the Acer One 10.
* lsm6dsx
- Rework leading to...
- External sensor support using the built in I2C master.
- Initial support for a slave lis2mdl magnetometer.
* meson-saradc
- Add temperature sensor support and bindings.
* st_magn
- New ID for lsm9dsl_magn with bindings
- New ID for lis3de accelerometer
* tpl0102
- Add supprot for IIO_AVAIL_RANGE to report the range available
from this device to userspace and in kernel users.
Cleanups and minor fixes
* tools
- Allow outside specification of CFLAGS
* ad2s90
- Handle and spi_read error.
- Handle spi_setup failure
- Drop a pointless assignment.
- Prevent a potentail race by moving device registration to after
all other setup.
- Add missing scale attribute.
- Add a sanity check on channel type before trying to read it.
* ad2s1210
- Move to modern gpio descriptors.
- Drop a gpioin flag which made no sense as far as we can tell.
- Add dt table (bindings doc to follow when this is ready for
moving out of staging).
* ad5933
- Drop camel-case naming of ext_clk_hz.
- White space fixes.
* ad7150
- Local variable to shorten overly long line.
- Alignment and line break fixes.
* ad7280a
- Handle an error path that was previously ignored.
- Use crc8.h to build the crc table replacing custom code.
- Avoid unecessary cast.
- Power down the device if an error happens in probe
- Use devm routines to simplify probe and remove.
* ad7606
- Alignment fixes.
* ad7780
- This worked as long as by coincidence an uninitialized value
was 0. Lets not rely on that.
- Ensure gain update is only used with the ad778x chips that
actually support it.
- Tidy up pattern mask generation.
- Read regulator when scale is requested (which should be infrequent)
as it might have changed from initialization.
* ad7816
- Move to modern gpio descriptors
- Don't use a busy_pin for ad7818 as there isn't one.
- Ensure RD/WR and CONVST pins are outputs (previously they
were brought up as inputs which doesn't seem to make any sense)
- DT id table.
* adc128s052
- SPDX
* adt7316
- Alignment fix.
- Fix data reading. When using I2C the driver never actually
used the value read. This has been broken a very long time
hence no rush to fix it now + the driver is undergoing a lot
of cleanup.
- Sanity check that the i2c read didn't fail to actually read
anything.
* dpot-dac
- Mark a switch full through with slightly different text so that
gcc doesn't warn on it.
* gyro-adc
- Fix a wrong file in the MAINTAINERS entry and add binding doc to the
listed files.
* ina2xx
- Add some early returns to clarify error paths in switch.
* lsm6dsx
- MAINTAINERS entry.
* max11100
- SPDX
* max9611
- SPDX
* mcp4131
- use of_device_get_match_data in preference to spi_get_device_id
approach.
* rcar-adc
- SPDX
* sc27xx
- Add ADC conversion timeout support to avoid possible fault.
* ssp_sensors
- Don't free managed resources manually.
* st-magn
- Add a comment to avoid future confusion over when to use -magn
postfix (on multi chip in package parts)
- Add BDU register for LIS3MDL where it seems to have been missed.
* st-sensors
- Minor spelling, grammar etc fixes.
* tpl0102
- Use a pointer rather than an index of an array to improve conciseness.
* tag 'iio-for-4.21a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (80 commits)
Staging: iio: adt7316: Add an extra check for 'ret' equals to 0
Staging: iio: adt7316: Fix i2c data reading, set the data field
dt-bindings: iio: adc: Add docs for ad7124
iio: adc: Add ad7124 support
dt-bindings: iio: adc: Add common ADCs properties to a separate file
iio: ad_sigma_delta: Allow to provide custom data register address
staging: iio: ad7816: Add device tree table.
iio: imu: st_lsm6dsx: add entry in MAINTAINERS file
iio: potentiometer: mcp4131: use of_device_get_match_data()
staging: iio: adc: ad7280a: use devm_* APIs
staging: iio: adc: ad7280a: power down the device on error in probe
dt-bindings: iio: imu: st_lsm6dsx: add support to i2c pullup resistors
iio: imu: st_lsm6dsx: add hw FIFO support to i2c controller
iio: imu: st_lsm6dsx: add st_lsm6dsx_push_tagged_data routine
iio: imu: st_lsm6dsx: add i2c embedded controller support
iio: imu: st_lsm6dsx: introduce st_lsm6dsx_sensor_set_enable routine
iio: imu: st_lsm6dsx: introduce ST_LSM6DSX_ID_EXT sensor ids
iio: imu: st_lsm6dsx: remove static from st_lsm6dsx_set_watermark
iio: imu: st_lsm6dsx: reload trimming parameter at bootstrap
iio: imu: st_lsm6dsx: introduce locked read/write utility routines
...
Add support for VCNL4035, which is capable of Ambient light
sensing (ALS) and proximity function. This patch adds support
only for ALS function
Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Before this commit sensor_hub_input_attr_get_raw_value() failed to take
the signedness of 16 and 8 bit values into account, returning e.g.
65436 instead of -100 for the z-axis reading of an accelerometer.
This commit adds a new is_signed parameter to the function and makes all
callers pass the appropriate value for this.
While at it, this commit also fixes up some neighboring lines where
statements were needlessly split over 2 lines to improve readability.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the big staging and IIO driver pull request for 4.20-rc1.
There are lots of things here, we ended up adding more lines than
removing, thanks to a large influx of Comedi National Instrument device
support. Someday soon we need to get comedi out of staging...
Other than the comedi drivers, the "big" things here are:
- new iio drivers
- delete dgnc driver (no one used it and no one had the hardware
anymore)
- vbox driver updates and fixes
- erofs fixes
- tons and tons of tiny checkpatch fixes for almost all staging
drivers
All of these have been in linux-next, with the last few happening a bit
"late" due to them getting stuck on my laptop during travel to the
Mantainers summit.
When merging with your tree, there will be 2 merge conflicts, both files
will be simple to resolve, just delete them :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW9bSGA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk5eACfYp73m9tLO22rnBcXJ73bWAYSTOMAn2GEL4Nc
LZBXs8QvvJIwfqmi7ofn
=UWJn
-----END PGP SIGNATURE-----
Merge tag 'staging-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO driver updates from Greg KH:
"Here is the big staging and IIO driver pull request for 4.20-rc1.
There are lots of things here, we ended up adding more lines than
removing, thanks to a large influx of Comedi National Instrument
device support. Someday soon we need to get comedi out of staging...
Other than the comedi drivers, the "big" things here are:
- new iio drivers
- delete dgnc driver (no one used it and no one had the hardware
anymore)
- vbox driver updates and fixes
- erofs fixes
- tons and tons of tiny checkpatch fixes for almost all staging
drivers
All of these have been in linux-next, with the last few happening a
bit "late" due to them getting stuck on my laptop during travel to the
Mantainers summit"
* tag 'staging-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (690 commits)
staging: gasket: Fix sparse "incorrect type in assignment" warnings.
staging: gasket: remove debug logs for callback invocation
staging: gasket: remove debug logs in page table mapping calls
staging: rtl8188eu: core: Use sizeof(*p) instead of sizeof(struct P) for memory allocation
staging: ks7010: Remove extra blank line
staging: gasket: Remove extra blank line
staging: media: davinci_vpfe: Fix spelling mistake in enum
staging: speakup: Add a pair of braces
staging: wlan-ng: Replace long int with long
staging: MAINTAINERS: remove obsolete IPX staging directory
staging: MAINTAINERS: remove NCP filesystem entry
staging: rtl8188eu: cleanup comparsions to false
staging: gasket: Update device virtual address comment
staging: gasket: sysfs: fix attribute release comment
staging: gasket: apex: fix sysfs_show
staging: gasket: page_table: simplify gasket_components_to_dev_address
staging: gasket: page_table: fix comment in components_to_dev_address
staging: gasket: page table: fixup error path allocating coherent mem
staging: gasket: page_table: rearrange gasket_page_table_entry
staging: gasket: page_table: remove unnecessary PTE status set to free
...
Add device tree support for ROHM BH1750 series ambient light sensors.
Signed-off-by: ryang <decatf@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Relying on CONFIG_PM_SLEEP to set PM ops is not necessary
since core will handle everything internally. One have to only make sure
that functions that can go unused are marked with __maybe_unused.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Drop boilerplate license text and use SPDX identifier instead.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Split regmap_config.use_single_rw into use_single_read and
use_single_write. This change enables drivers of devices which only
support bulk operations in one direction to use the regmap_bulk_*()
functions for both directions and have their bulk operation split into
single operations only when necessary.
Update all struct regmap_config instances where use_single_rw==true to
instead set both use_single_read and use_single_write. No attempt was
made to evaluate whether it is possible to set only one of
use_single_read or use_single_write.
Signed-off-by: David Frey <dpfrey@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Variable max44000_alstim_shift is defined but is never used hence it is
redundant and can be removed. This variable has been like this since
the driver was added back in 2016.
Cleans up clang warning:
warning: 'max44000_alstim_shift' defined but not used [-Wunused-const-variable=]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds support for the regulator framework to the tsl2772
driver. Driver was tested using a LG Nexus 5 (hammerhead) phone with
the two regulators and on a Raspberry Pi 2 without any regulators
controlling the power to the sensor.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds support for optionally reading the proximity led diode
and current settings from device tree. This was tested using a LG
Nexus 5 (hammerhead) which requires a different diode than the driver
default for the IR LED.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Read response register to detect any error.
Signed-off-by: Maxime Roussin-Bélanger <maxime.roussinbelanger@gmail.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The current check on val always results in true and so the
call to sii1133_update_adcsens never gets called. Fix this check
so it returns with -EINVAL only when val is not zero and not one.
Detected by CoverityScan, CID#1472099 ("Logically dead code")
Fixes: e01e7eaf37 ("iio: light: introduce si1133")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
VCNL4200 is an integrated long distance (up to 1500mm) proximity and
ambient light sensor.
The support is very basic. There is no configuration of proximity and
ambient light sensing yet. Only the reading of both measured values is
done.
The reading of ambient light and proximity values is blocking. If you
request a new value too early, the driver waits for new value to be
ready.
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We can detect incorrectly specified device id for some chips, so warn
user in that case.
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver already supports VCNL4010/20 devices. The currently supported
features and detectable product id are the same, so add shared id for
them.
This is a groundwork to extend the driver by detecting incorrectly
specified device id.
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There are similar chips in the vcnl4xxx family. The initialization and
communication is a bit different for members of the family, so this
patch makes the driver extendable for different chips.
There is no functional change.
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There are also a couple of fixes that can wait for the coming merge
window.
Core new features
* Support for phase channels (used in time of flight sensors amongst
other things)
* Support for deep UV light channel modifier.
New Device Support
* AD4758 DAC
- New driver and dt bindings.
* adxl345
- Support the adxl375 +-200g part which is register compatible.
* isl29501 Time of flight sensor.
- New driver
* meson-saradc
- Support the Meson8m2 Socs - right now this is just an ID, but there will
be additional difference in future.
* mpu6050
- New ID for 6515 variant.
* si1133 UV sensor.
- New driver
* Spreadtrum SC27xx PMIC ADC
- New driver and dt bindings.
Features
* adxl345
- Add calibration offset readback and writing.
- Add sampling frequency control.
Fixes and Cleanups
* ad5933
- Use a macro for the channel definition to reduce duplication.
* ad9523
- Replace use of core mlock with a local lock. Part of ongoing efforts
to avoid confusing the purpose of mlock which is only about iio core
state changes.
- Fix displayed phase which was out by a factor of 10.
* adxl345
- Add a link to the datasheet.
- Rework the use of the address field in the chan_spec structures to
allow addition of more per channel information.
* adis imu
- Mark switch fall throughs.
* at91-sama5d2
- Fix some casting on big endian systems.
* bmp280
- Drop some DT elements that aren't used and should mostly be done from
userspace rather than in DT.
* hx711
- add clock-frequency dt binding and resulting delay to deal with capacitance
issue on some boards.
- fix a spurious unit-address in the example.
* ina2xx
- Avoid a possible kthread_stop with a stale task_struct.
* ltc2632
- Remove some unused local variables (assigned but value never used).
* max1363
- Use device_get_match_data to remove some boilerplate.
* mma8452
- Mark switch fall throughs.
* sca3000
- Fix a missing return in a switch statement (a bad fallthrough
previously!)
* sigma-delta-modulator
- Drop incorrect unit address from the DT example.
* st_accel
- Use device_get_match_data to drop some boiler plate.
- Move to probe_new for i2c driver as second parameter not used.
* st_sensors library
- Use a strlcpy (safe in this case).
* st_lsm6dsx
- Add some error logging.
* ti-ads7950
- SPDX
- Allow simultaneous buffered and polled reads. Needed on a Lego Mindstorms
EV3 where some channels are used for power supply monitoring at a very low
rate.
* ti-dac5571
- Remove an unused variable.
* xadc
- Drop some dead code.
-----BEGIN PGP SIGNATURE-----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=T+hS
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.19b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO new device support, features and cleanups.
There are also a couple of fixes that can wait for the coming merge
window.
Core new features
* Support for phase channels (used in time of flight sensors amongst
other things)
* Support for deep UV light channel modifier.
New Device Support
* AD4758 DAC
- New driver and dt bindings.
* adxl345
- Support the adxl375 +-200g part which is register compatible.
* isl29501 Time of flight sensor.
- New driver
* meson-saradc
- Support the Meson8m2 Socs - right now this is just an ID, but there will
be additional difference in future.
* mpu6050
- New ID for 6515 variant.
* si1133 UV sensor.
- New driver
* Spreadtrum SC27xx PMIC ADC
- New driver and dt bindings.
Features
* adxl345
- Add calibration offset readback and writing.
- Add sampling frequency control.
Fixes and Cleanups
* ad5933
- Use a macro for the channel definition to reduce duplication.
* ad9523
- Replace use of core mlock with a local lock. Part of ongoing efforts
to avoid confusing the purpose of mlock which is only about iio core
state changes.
- Fix displayed phase which was out by a factor of 10.
* adxl345
- Add a link to the datasheet.
- Rework the use of the address field in the chan_spec structures to
allow addition of more per channel information.
* adis imu
- Mark switch fall throughs.
* at91-sama5d2
- Fix some casting on big endian systems.
* bmp280
- Drop some DT elements that aren't used and should mostly be done from
userspace rather than in DT.
* hx711
- add clock-frequency dt binding and resulting delay to deal with capacitance
issue on some boards.
- fix a spurious unit-address in the example.
* ina2xx
- Avoid a possible kthread_stop with a stale task_struct.
* ltc2632
- Remove some unused local variables (assigned but value never used).
* max1363
- Use device_get_match_data to remove some boilerplate.
* mma8452
- Mark switch fall throughs.
* sca3000
- Fix a missing return in a switch statement (a bad fallthrough
previously!)
* sigma-delta-modulator
- Drop incorrect unit address from the DT example.
* st_accel
- Use device_get_match_data to drop some boiler plate.
- Move to probe_new for i2c driver as second parameter not used.
* st_sensors library
- Use a strlcpy (safe in this case).
* st_lsm6dsx
- Add some error logging.
* ti-ads7950
- SPDX
- Allow simultaneous buffered and polled reads. Needed on a Lego Mindstorms
EV3 where some channels are used for power supply monitoring at a very low
rate.
* ti-dac5571
- Remove an unused variable.
* xadc
- Drop some dead code.
e-mail received from Silicon Lab to confirm that the licensing
isn't a problem.
"
Dear Maxime Roussin-Belanger,
The LUX calculation code only works with Si1133.
As long as the software is used with Silicon Lab's sensor product,
I don't see any problem.
Regards,
Tony
"
Signed-off-by: Maxime Roussin-Bélanger <maxime.roussinbelanger@gmail.com>
Reviewed-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It may be possible for tsl2772_get_lux to return a zero lux value
and hence a division by zero can occur when lux_val is zero. Check
for this case and return -ERANGE to avoid the division by zero.
Detected by CoverityScan, CID#1469484 ("Division or modulo by zero")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The times reported by the in_illuminance_integration_time_available
sysfs attribute are actually in milliseconds, not microseconds. This
patch corrects the times with the correct unit.
The fixes tag is inaccurate as the issue existed when the driver
was still in staging. However, lots of changes occured before
it graduated so this is as a good a point as any for backports.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Fixes: f44d5c8ac3 ("staging: iio: tsl2583: move out of staging")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move the tsl2772 driver out of staging and into mainline.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Similar to other common iio frameworks, move cros_ec_sensors_core.h from
drivers/iio/common/cros_ec_sensors/ to include/linux/iio/common.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Usually, functions responsible for reading raw data typically relies on
values from iio_chan_info_enum to correctly identify the type of data to
be read. There is a set of a device driver that uses the magic number 0
instead of IIO_CHAN_INFO_RAW. This patch improves the readability by
replaces the magic number 0 for the appropriate IIO_CHAN_INFO_RAW in six
devices driver in the IIO subsystem.
Signed-off-by: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds support for the On Semiconductor LV0104CS ambient
light sensor.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If an application set a tight sampling frequency, given the interrupt
use is a wakeup source, suspend will not happen: the kernel will receive
a wake up interrupt and will cancel the suspend process.
Given cros_ec sensors type is non wake up, this patch adds prepare and
complete callbacks to set 1s sampling period just before suspend. This
ensures the sensor hub will not be a source of interrupt during the
suspend process.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add GPLv2+ SPDX identifier and update email for author's drivers.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Structures st_uvis25_i2c_regmap_config and st_uvis25_spi_regmap_config are
local to the source and do not need to be in global scope, so make them
both static.
Cleans up sparse warnings:
warning: symbol 'st_uvis25_i2c_regmap_config' was not declared. Should
it be static?
warning: symbol 'st_uvis25_spi_regmap_config' was not declared. Should
it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
add support for STMicroelectronics UVIS25 uv sensor
http://www.st.com/resource/en/datasheet/uvis25.pdf
- continuos mode support
- i2c support
- spi support
- trigger mode support
- system PM support
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Driver for 20-bit ALS and UV B sensor with I2C interface exposing
the following API:
in_uvindex_input
in_illuminance_raw
in_illuminance_scale
in_illuminance_scale_available
in_intensity_uv_raw
in_intensity_uv_scale
in_intensity_uv_scale_available
integration_time
integration_time_available
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix gcc warnings about variable 'ec_device' being set but not used
in these files:
common/cros_ec_sensors/cros_ec_sensors.c:194:25
light/cros_ec_light_prox.c:184:25
Signed-off-by: Paolo Cretaro <paolocretaro@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd atomisp
cleanups (take the media tree's version).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgnFrg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymxbwCgtNlBkqD2JJYpLRKvI/C4w1vzZsEAnA2THRkt
g3ioPBqmqC/2DSbldr2o
=/ebw
-----END PGP SIGNATURE-----
Merge tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO updates from Greg KH:
"Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd
atomisp cleanups (take the media tree's version)"
* tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (507 commits)
staging: lustre: add SPDX identifiers to all lustre files
staging: greybus: Remove redundant license text
staging: greybus: add SPDX identifiers to all greybus driver files
staging: ccree: simplify ioread/iowrite
staging: ccree: simplify registers access
staging: ccree: simplify error handling logic
staging: ccree: remove dead code
staging: ccree: handle limiting of DMA masks
staging: ccree: copy IV to DMAable memory
staging: fbtft: remove redundant initialization of buf
staging: sm750fb: Fix parameter mistake in poke32
staging: wilc1000: Fix bssid buffer offset in Txq
staging: fbtft: fb_ssd1331: fix mirrored display
staging: android: Fix checkpatch.pl error
staging: greybus: loopback: convert loopback to use generic async operations
staging: greybus: operation: add private data with get/set accessors
staging: greybus: loopback: Fix iteration count on async path
staging: greybus: loopback: Hold per-connection mutex across operations
staging: greybus/loopback: use ktime_get() for time intervals
staging: fsl-dpaa2/eth: Extra headroom in RX buffers
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reported scale was only correct for the default settings of 100 ms
integration time and gain 1.
This aligns the reported scale with the behaviour of any other IIO driver
and the documented ABI, but may require userspace changes if someone uses
non-default settings.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Instead of manually iterating the array of allowed gain values, use
find_closest. Storing the current gain setting avoids accessing the
hardware on each query.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Instead of reading the value from the register on each query, store the
set value.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This improves code uniformity (range checks for als_gain are also done
in the setter). Also unmangle rounding and calculation of register value.
The calculated integration time it_ms is required in the next patch of
the series.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The TCS3472 device provides interrupt signal for out-of-threshold events
with persistence filter.
This change adds interrupt support for the threshold events and enables
to configure the period of time by persistence filter.
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
New device support:
* ak8974
- support the AMI306.
* st_magnetometer
- add support for the LIS2MDL with bindings.
* rockchip-saradc
- add binding for rv1108 SoC (no driver change).
* srf08
- add srf02 (i2c only) and srf10 support.
* stm32-timer
- support for the STM32H7 to existing driver.
Features:
* tools
- move over to the tools buildsystem rather than hand rolling.
- add an install section to the build.
* ak8974
- use serial number to add device randomness.
- add AMI306 calibration data output.
* ccs811
- triggered buffer support.
* srf08
- add a device tree table as the old style i2c probing is going away,
- add triggered buffer support
* st32-adc
- add optional st,min-sample-time-nsecs binding to allow control of
sampling against analog circuitry.
* stm32-timer
- add output compare triggers.
* ti-ads1015
- add threshold event support.
* ti-ads7950
- Allow use on ACPI platforms including providing a default reference
voltage as there is no way to obtain this on ACPI currently.
Cleanup and fixes:
* ad7606
- fix an error return code in probe.
* ads1015
- fix incorrect data rate setting update when capture in progress,
- fix wrong scale information for the ADS1115,
- make conversions work when CONFIG_PM is not set,
- make sure we don't get a stale result after a runtime resume by
ensuring we wait long enough,
- avoid returning a false error form the buffer setup callbacks,
- add enough wait time to get the correct conversion,
- remove an unnecessary config register update,
- add a helper to set conversion mode reducing repeated boilerplate,
- use devm_iio_triggered_buffer_setup to simplify error and remove
paths,
- use iio_device_claim_direct_mode instead of opencoding the same.
* ak8974
- mark the INT_CLEAR register as precious to prevent debugfs access.
* apds9300
- constify the i2c_device_id.
* at91-sama5 adc
- add missing Kconfig dependency.
* bma180 accel
- constify the i2c_device_id.
* rockchip_saradc
- explicitly request exclusive reset control as part of the reset rework
on going throughout the kernel.
* st_accel
- fix drdy configuration for a load of accelerometers that only have
the int1 line. Fix is unimportant as presumably no deviec tree actually
used the non existent hardware line.
* st_pressure
- fix drdy configuration for LPS22HB and LPS25H by dropping int2 support
as they don't have this. Fix is unimportant as presumably no device tree
actually used the non existent hardware line.
* stm32-dac
- explicitly request exclusive reset control (part of reset being reworked).
* tsl2583
- constify the i2c_device_id.
* xadc
- coding style fixes.
-----BEGIN PGP SIGNATURE-----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=b6g8
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.14b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO new device support, features and cleanup for the 4.14 cycle.
New device support:
* ak8974
- support the AMI306.
* st_magnetometer
- add support for the LIS2MDL with bindings.
* rockchip-saradc
- add binding for rv1108 SoC (no driver change).
* srf08
- add srf02 (i2c only) and srf10 support.
* stm32-timer
- support for the STM32H7 to existing driver.
Features:
* tools
- move over to the tools buildsystem rather than hand rolling.
- add an install section to the build.
* ak8974
- use serial number to add device randomness.
- add AMI306 calibration data output.
* ccs811
- triggered buffer support.
* srf08
- add a device tree table as the old style i2c probing is going away,
- add triggered buffer support
* st32-adc
- add optional st,min-sample-time-nsecs binding to allow control of
sampling against analog circuitry.
* stm32-timer
- add output compare triggers.
* ti-ads1015
- add threshold event support.
* ti-ads7950
- Allow use on ACPI platforms including providing a default reference
voltage as there is no way to obtain this on ACPI currently.
Cleanup and fixes:
* ad7606
- fix an error return code in probe.
* ads1015
- fix incorrect data rate setting update when capture in progress,
- fix wrong scale information for the ADS1115,
- make conversions work when CONFIG_PM is not set,
- make sure we don't get a stale result after a runtime resume by
ensuring we wait long enough,
- avoid returning a false error form the buffer setup callbacks,
- add enough wait time to get the correct conversion,
- remove an unnecessary config register update,
- add a helper to set conversion mode reducing repeated boilerplate,
- use devm_iio_triggered_buffer_setup to simplify error and remove
paths,
- use iio_device_claim_direct_mode instead of opencoding the same.
* ak8974
- mark the INT_CLEAR register as precious to prevent debugfs access.
* apds9300
- constify the i2c_device_id.
* at91-sama5 adc
- add missing Kconfig dependency.
* bma180 accel
- constify the i2c_device_id.
* rockchip_saradc
- explicitly request exclusive reset control as part of the reset rework
on going throughout the kernel.
* st_accel
- fix drdy configuration for a load of accelerometers that only have
the int1 line. Fix is unimportant as presumably no deviec tree actually
used the non existent hardware line.
* st_pressure
- fix drdy configuration for LPS22HB and LPS25H by dropping int2 support
as they don't have this. Fix is unimportant as presumably no device tree
actually used the non existent hardware line.
* stm32-dac
- explicitly request exclusive reset control (part of reset being reworked).
* tsl2583
- constify the i2c_device_id.
* xadc
- coding style fixes.
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* ad2s1210
- Fix negative angular velocity reads (identified by a gcc 7 warning)
* aspeed-adc
- Wait for initialization sequence to finish before enabling channels.
Without it no channels work.
* axp288
- Revert a patch that dropped some bogus register mods. No one is entirely
sure why but it breaks charging on some devices.
- Fix GPADC pin read returning 0. Turns out a small sleep is needed.
* bmc150
- Make sure device is restored to normal state after suspend / resume
cycle. Otherwise, simple sysfs reads are broken.
* tsl2563
- fix wrong event code.
* st-accel
- add spi 3-wire support. Needed to fix the lsm303agr accelerometer
which only had 3 wires in all cases. Side effect is to enable optional
3-wire support for other devices.
* st-pressure
- disable multiread by default for LPS22HB (only effects SPI)
* sun4i-gpadc-iio
- fix unbalanced irq enable / disable
* vf610
- Fix VALT slection for REFSEL bits - ensures we are using the
right reference pins.
-----BEGIN PGP SIGNATURE-----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=BApO
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.13a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 4.13 cycle.
* ad2s1210
- Fix negative angular velocity reads (identified by a gcc 7 warning)
* aspeed-adc
- Wait for initialization sequence to finish before enabling channels.
Without it no channels work.
* axp288
- Revert a patch that dropped some bogus register mods. No one is entirely
sure why but it breaks charging on some devices.
- Fix GPADC pin read returning 0. Turns out a small sleep is needed.
* bmc150
- Make sure device is restored to normal state after suspend / resume
cycle. Otherwise, simple sysfs reads are broken.
* tsl2563
- fix wrong event code.
* st-accel
- add spi 3-wire support. Needed to fix the lsm303agr accelerometer
which only had 3 wires in all cases. Side effect is to enable optional
3-wire support for other devices.
* st-pressure
- disable multiread by default for LPS22HB (only effects SPI)
* sun4i-gpadc-iio
- fix unbalanced irq enable / disable
* vf610
- Fix VALT slection for REFSEL bits - ensures we are using the
right reference pins.
Set up and use triggered buffer if there is irq defined for device in
device tree. Trigger producer triggers from rpr0521 drdy interrupt line.
Trigger consumer reads rpr0521 data to scan buffer.
Depends on previous commits of _scale and _offset.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add a link to the TCS3472 datasheet in the AMS's website.
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The integration time is controlled by the ATIME register only. However,
this register is written by i2c_smbus_write_word_data() in write_raw().
We actually don't need to write a subsequent register. So just use
i2c_smbus_write_byte_data() instead.
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The TSL2563 driver provides three iio channels, two of which are raw ADC
channels (channel 0 and channel 1) in the device and the remaining one
is calculated by the two. The ADC channel 0 only supports programmable
interrupt with threshold settings and this driver supports the event but
the generated event code does not contain the corresponding iio channel
type.
This is going to change userspace ABI. Hopefully fixing this to be
what it should always have been won't break any userspace code.
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Move proximity channel from last to first in structs to avoid confusion
later with buffered triggers. Proximity data output is first in rpr0521
register map.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add sysfs read/write proximity offset feature. Offset is read/write from
sensor registers. Values are proximity raw 10-bit values. After applying
offset value, output values will be (measured_raw - offset_value). Output
values are unsigned so offset value doesn't make output negative.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Just whitespace change, no functional changes.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Changed magic number to sizeof() on value read.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Refactor _set_power_state(), _resume() and _suspend().
Enable measurement only when needed, not in _init(). System can suspend
during measurement and measurement is continued on resume.
Pm turns off measurement when both ps and als measurements are disabled for
2 seconds. During off-time the power save is 20-500mA, typically 180mA.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Set sensor measurement off after probe fail in pm_runtime_set_active() or
iio_device_register(). Without this change sensor measurement stays on
even though probe fails on these calls.
This is maybe rare case, but causes constant power drain without any
benefits when it happens. Power drain is 20-500uA, typically 180uA.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Sensor was marked enabled on each call even if the call was for disabling
sensor.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The register mapping for the IIO driver for the Liteon Light and Proximity
sensor LTR501 interrupt mode is interchanged (ALS/PS).
There is a register called INTERRUPT register (address 0x8F)
Bit 0 represents PS measurement trigger.
Bit 1 represents ALS measurement trigger.
This two bit fields are interchanged within the driver.
see datasheet page 24:
http://optoelectronics.liteon.com/upload/download/DS86-2012-0006/S_110_LTR-501ALS-01_PrelimDS_ver1%5B1%5D.pdf
Signed-off-by: Franziska Naepelt <franziska.naepelt@idt.com>
Fixes: 7ac702b314 ("iio: ltr501: Add interrupt support")
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes the following warning when building with clang:
drivers/iio/light/isl29018.c:808:36: error: variable
'isl29018_acpi_match' is not needed and will not be emitted
[-Werror,-Wunneeded-internal-declaration]
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds runtime power management support to the tsl2583 driver.
The device is powered off after two seconds of inactivity. Verified that
the driver still functions correctly using a TSL2581 hooked up to a
Raspberry Pi 2.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
isl29030 is basically the same chip. The only difference
is the chip's first pin. For isl29028 its named ADDR0 and
can be used to change the chip's i2c address. For isl29030
on the other hand that pin is named Ials and is an analog
current output proportional to ALS/IR. This change is
irrelevant for the Linux driver.
This has been tested on Motorola Droid 4.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Move ISL29028 ALS / Proximity Sensor out of staging and into mainline.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
APDS9960 can safely force runtime suspend if the system wants
to enter system-wide suspend
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Check for attribute_group structures that are only stored in the
event_attrs filed of iio_info structure. As the event_attrs field of
iio_info structures is constant, so these attribute_group structures can
also be declared constant. Done using coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct attribute_group i@p = {...};
@ok1@
identifier r1.i;
position p;
struct iio_info x;
@@
x.event_attrs=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
static
+const
struct attribute_group i={...};
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct attribute_group i;
As the attrs field of iio_info structures is also constant, so these
attribute_group structures can also be declared constant. Done manually.
File size before:
text data bss dec hex filename
5798 2376 0 8174 1fee drivers/iio/light/lm3533-als.o
File size after:
text data bss dec hex filename
5926 2248 0 8174 1fee drivers/iio/light/lm3533-als.o
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Check for attribute_group structures that are only stored in the
attrs filed of iio_info structure. As the attrs field of iio_info
structures is constant, so these attribute_group structures can also be
declared constant.
Done using coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct attribute_group i@p = {...};
@ok1@
identifier r1.i;
position p;
struct iio_info x;
@@
x.attrs=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
static
+const
struct attribute_group i={...};
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct attribute_group i;
File size before:
text data bss dec hex filename
8503 488 0 8991 231f drivers/iio/light/apds9960.o
File size after:
text data bss dec hex filename
8567 424 0 8991 231f drivers/iio/light/apds9960.o
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Check for attribute_group structures that are only stored in the
attrs filed of iio_info structure. As the attrs field of iio_info
structures is constant, so these attribute_group structures can also be
declared constant.
Done using coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct attribute_group i@p = {...};
@ok1@
identifier r1.i;
position p;
struct iio_info x;
@@
x.attrs=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
static
+const
struct attribute_group i={...};
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct attribute_group i;
File size before:
text data bss dec hex filename
2276 352 0 2628 a44 drivers/iio/light/bh1750.o
File size after:
text data bss dec hex filename
2340 320 0 2660 a64 drivers/iio/light/bh1750.o
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for STMicro VL6180 - ALS, range and proximity sensor. Sensor is capable of measuring the light
intensity as well as object distance using TOF (Time of Flight) technology.
Signed-off-by: Manivannan Sadhasivam <manivannanece23@gmail.com>
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add HID_USAGE_SENSOR_HUMAN_PRESENCE support for Human Presence sensitivity
parsing, in case some implementation uses it as sensitivity modifier.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Handle Light and Proximity sensors presented by the ChromeOS EC Sensor hub.
Creates an IIO device for each functions.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
New device support:
* lsm6dsx imu
- new driver and bindings.
* max11100 adc
- new driver and bindings.
* tlc4541
- new driver
* tmp007 thermopile
- new driver.
Core
* in kernel interfaces
- pass through raw values if no scaling provided and a processed value is
requested.
* trigger
- close a race condition in acquiring trigger reference.
- constify device_type structures.
- rework the viio_trigger_alloc function to be much neater and easier to
read.
- free trigger resources correctly on some error paths. Avoids putting a
module we don't have.
Documentation
* ABI
- specify a unit for proximity measurements.
Cleanups and features
* ads1015
- constify iio_info structure.
* ads7950 cleanups following merge in previous pull
- Add device tree bindings
- Drop the ti prefix from the module name in common with other drivers.
- Change regulator name to vref to match datasheet and other drivers.
* ak8974
- remove a redundant zero timeout check.
* bmi160
- use variable names for sizeof instead of types.
* cm3605
- mark PM functions as __maybe_unused to avoid a build warning.
* isl29028 (on it's way towards moving out of staging).
- alignment fixes and newline improvements.
- combine proxim_get and read_proxim for simpler code.
- drop unused ISL29028_DEV_ATTR macro
- move some error logging into functions to cut out repitition.
- make error messages more consistent.
- tidy up some brackets.
- drop the enable flag that nothing uses.
- only set proximity rate and ALS scale when relevant channel type is enabled.
- runtime pm support.
* lsm6dsx
- fix wrong values for gyro sensitivitiy.
* mag3110
- claim direct mode during sysfs reads to avoid a race condition.
* max1363
- export OF device table IDs as module aliases.
* max30100
- use msleep for long uncritical delays.
* mcp4531
- export OF device table as module aliases.
* ms5611
- claim direct mode during sysfs reads to avoid a race condition.
* opt3001
- export OF device table as module aliases.
* sx9500
- claim direct mode during oversampling changes to avoid a race condition.
-----BEGIN PGP SIGNATURE-----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=Wvje
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.11b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into work-next
Jonathan writes:
Second round of IIO new device support, cleanups and features for the 4.11 cycle
New device support:
* lsm6dsx imu
- new driver and bindings.
* max11100 adc
- new driver and bindings.
* tlc4541
- new driver
* tmp007 thermopile
- new driver.
Core
* in kernel interfaces
- pass through raw values if no scaling provided and a processed value is
requested.
* trigger
- close a race condition in acquiring trigger reference.
- constify device_type structures.
- rework the viio_trigger_alloc function to be much neater and easier to
read.
- free trigger resources correctly on some error paths. Avoids putting a
module we don't have.
Documentation
* ABI
- specify a unit for proximity measurements.
Cleanups and features
* ads1015
- constify iio_info structure.
* ads7950 cleanups following merge in previous pull
- Add device tree bindings
- Drop the ti prefix from the module name in common with other drivers.
- Change regulator name to vref to match datasheet and other drivers.
* ak8974
- remove a redundant zero timeout check.
* bmi160
- use variable names for sizeof instead of types.
* cm3605
- mark PM functions as __maybe_unused to avoid a build warning.
* isl29028 (on it's way towards moving out of staging).
- alignment fixes and newline improvements.
- combine proxim_get and read_proxim for simpler code.
- drop unused ISL29028_DEV_ATTR macro
- move some error logging into functions to cut out repitition.
- make error messages more consistent.
- tidy up some brackets.
- drop the enable flag that nothing uses.
- only set proximity rate and ALS scale when relevant channel type is enabled.
- runtime pm support.
* lsm6dsx
- fix wrong values for gyro sensitivitiy.
* mag3110
- claim direct mode during sysfs reads to avoid a race condition.
* max1363
- export OF device table IDs as module aliases.
* max30100
- use msleep for long uncritical delays.
* mcp4531
- export OF device table as module aliases.
* ms5611
- claim direct mode during sysfs reads to avoid a race condition.
* opt3001
- export OF device table as module aliases.
* sx9500
- claim direct mode during oversampling changes to avoid a race condition.
The I2C core always reports a MODALIAS of the form i2c:<foo> even if the
device was registered via OF, this means that exporting the OF device ID
table device aliases in the module is not needed. But in order to change
how the core reports modaliases to user-space, it's better to export it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When CONFIG_PM_SLEEP is disabled, we get a harmless warning
drivers/iio/light/cm3605.c:292:12: error: 'cm3605_pm_resume' defined but not used [-Werror=unused-function]
drivers/iio/light/cm3605.c:281:12: error: 'cm3605_pm_suspend' defined but not used [-Werror=unused-function]
Marking the functions as possibly unused avoids the warning without
needing to add an #ifdef.
Fixes: 8afa505c12 ("iio: light: add driver for Capella CM3605")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
It's shaping to be another fairly busy cycle. Lots more on the way!
New device support
* ads7950
- new driver supporting ads7950, ads7951, ads7952, ads7953, ads7954,
ads7955, ads7956, ads7957, ads7958, ads7959, ads7960, and ads7961 ADCs.
* cm3605
- New driver for this light sensor and proximity sensor which is an
analog part with some additional digital controls.
* hx711
- New driver.
Core new stuff
* Gravity sensor type. This is a processed datastream in which the device
will try to work out which way is down.
* Split the buffer.h file into two parts. One provides the interface to 'use'
a buffer, the second provides the internals of the buffer functionality as
needed by implementations of buffers.
- Move documentation inline so as to allow use of private: tag when
generating documentation.
- Add some utility functions for the few things that are directly done
with the buffers.
- Stop exporting functions that no-one uses outside of the core code.
- Push docs down by the code in the c file where they should have always
been.
- Fix typo in kernel-doc for buffer.
- push down some includes that were previously happening implicitly.
- stop enabling the timestamp of the dummy device.
Features and cleanups
* ad5592r
- ACPI support
* ad5593r
-ACPI support.
* ad5933
- Fix a false comment about size of a particular register.
* ad7150
- replace S_IRUGO | S_IWUSR with 0644. I'm not that keen on these patches
in general, but as it was nicely presented I took this one anyway. As a
general rule will only take these as part of a larger driver cleanup.
- don't eat an error but rather reutnr it in the write_event_config callback.
* ad7606
- replace non standard range attibute with _scale
* ade7753
- use usleep_range for short sleeps
* ade7754
- use usleep_range for short sleeps
* ade7758
- use usleep_range for short sleeps
* ade7759
- use usleep_range for short sleeps
* ade7854
- use usleep_range for short sleeps
* adis16201
- fix description
* adis16203
- fix description
- fix copyright year
* adis16209
- fix description
* adt7316
- Add braces to arms of if else statement (for consistency)
- Alignment fixes.
* axp288
- Fix up an issue with accidental overwrites of data.
* bmi160
- add deivce tables for i2c and spi to support correctly identifying the
full dt name (including manufacturer).
- device tree binding.
* bmp280
- use usleep_range for short sleeps.
* cm3232
- return error from cm3232_reg_init rather than eating it if the last write
fails.
* dummy driver
- remove a semicolor found at end of a function defintition.
* exynos-adc
- use usleep_range for short sleeps.
* hid-sensor (accel)
- Add timestamp support. The hardware can provide timestamps so lets support
them. If not fall back to timestamps estimated in kernel.
* hid-sensor (light)
- Add a duplicate ID for the light channels so as to keep existing interface
whilst also using the more standard IIO interface.
* hts221
- acpi probing
* imx25-gcq
- Add a macro call to allow this driver to be automatically loaded.
* isl29028
- reorganise code to avoid deep nesting of if statements.
- move chip test and default regs into a function suitable or sharing with
power management code.
- tidy up some code alignment.
* lidar-lite-v3
- introduce compatible strings that make it clear Garmin have consideral
friends.
* mma8452
- avoid returning signed value when unsigned is appropriate
* spmi-vadc
- Update function for generic voltage conversion to take into account that
different channels on this device should be handled differently.
- Rework code to allow per channel voltage scaling and support the standard
options for this hardware.
- Fixup three minor issues with the above patches for this part. These all
effect test builds rather than the native builds for the part, but good to
clean them up anyway.
* st_sensors
- support device matching from the ACPI DST tables.
- acpi based probing for accelerometers
- acpi based probing for pressure sensors
- Allow pressure sensors to read negative values.
- Export sampling frequency for lps25h and lps331ap.
- Add support for the old DT bindings from the period when these deivces
were often supported through windows.
Docs fixup:
* typo in sysfs-bus-iio
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAlh2bhcRHGppYzIzQGtl
cm5lbC5vcmcACgkQVIU0mcT0FogdSQ/9Hyd3ic5AgWyDKr9JI1vJPj3kT0PIYHLk
4ucbQ8HUJQBBLnsausTb+UwuGV277DkVjGVsI4epn59H3CvkNh3Egl3XCmbhIpt2
oyl9Pw9dSon6n/7I5pNSwmqD45O+aB7qFLigIfLmciwpMHZly3ExzGBMpqUkgjf9
bVzndDqrfoNIrU7UaMD6QgrSxrgYJJJJwBDig/0zjAkGvu9L8a8ghrKkrRzMy62O
nGP5mmEagivFF9lpGzzrw2pYBQWY4AFbsNvuLElE7nUz0PKKG+9J0oaBiglTYv2p
mkNlYl7iTZfI3eFOXa+7HdSmeNhYX2dvbEM2jAA/Mr6ojWg2mSRu7Y19Kl2KP7K7
BDRKBw+Cp0wkVvJ8LU/6PiDSmqp09VfjjqevzVGJi/BmWLzG0Mi2OsQmmynbw2SV
hxiGETRV7vBoyJWDJuwJoftZaRnHWJbiQ6ftEUbWOFA9RIBMgOJBiL+RtxerJkHv
FWlCFpv/618TUB/uM15+EOLVJAT5b7K+6+l6EGEjWdjiS/7vL7QM5DL8w4zV43zz
cQ98UeIlqCkvoFmx9uHbl44COLQgzNtxAjytLxqbsOmEb40wlzoNzgSoUGu73SaG
8qwznH0w0p8P1nyzwe9qKKK6SmFhj/tF6jKVmIi/H7wJdA1J5dAAmwFUBSxLs2DX
u1eM3ikCl/M=
=yjUA
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.11a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of new device support, features and cleanups for IIO in the 4.11 cycle.
It's shaping to be another fairly busy cycle. Lots more on the way!
New device support
* ads7950
- new driver supporting ads7950, ads7951, ads7952, ads7953, ads7954,
ads7955, ads7956, ads7957, ads7958, ads7959, ads7960, and ads7961 ADCs.
* cm3605
- New driver for this light sensor and proximity sensor which is an
analog part with some additional digital controls.
* hx711
- New driver.
Core new stuff
* Gravity sensor type. This is a processed datastream in which the device
will try to work out which way is down.
* Split the buffer.h file into two parts. One provides the interface to 'use'
a buffer, the second provides the internals of the buffer functionality as
needed by implementations of buffers.
- Move documentation inline so as to allow use of private: tag when
generating documentation.
- Add some utility functions for the few things that are directly done
with the buffers.
- Stop exporting functions that no-one uses outside of the core code.
- Push docs down by the code in the c file where they should have always
been.
- Fix typo in kernel-doc for buffer.
- push down some includes that were previously happening implicitly.
- stop enabling the timestamp of the dummy device.
Features and cleanups
* ad5592r
- ACPI support
* ad5593r
-ACPI support.
* ad5933
- Fix a false comment about size of a particular register.
* ad7150
- replace S_IRUGO | S_IWUSR with 0644. I'm not that keen on these patches
in general, but as it was nicely presented I took this one anyway. As a
general rule will only take these as part of a larger driver cleanup.
- don't eat an error but rather reutnr it in the write_event_config callback.
* ad7606
- replace non standard range attibute with _scale
* ade7753
- use usleep_range for short sleeps
* ade7754
- use usleep_range for short sleeps
* ade7758
- use usleep_range for short sleeps
* ade7759
- use usleep_range for short sleeps
* ade7854
- use usleep_range for short sleeps
* adis16201
- fix description
* adis16203
- fix description
- fix copyright year
* adis16209
- fix description
* adt7316
- Add braces to arms of if else statement (for consistency)
- Alignment fixes.
* axp288
- Fix up an issue with accidental overwrites of data.
* bmi160
- add deivce tables for i2c and spi to support correctly identifying the
full dt name (including manufacturer).
- device tree binding.
* bmp280
- use usleep_range for short sleeps.
* cm3232
- return error from cm3232_reg_init rather than eating it if the last write
fails.
* dummy driver
- remove a semicolor found at end of a function defintition.
* exynos-adc
- use usleep_range for short sleeps.
* hid-sensor (accel)
- Add timestamp support. The hardware can provide timestamps so lets support
them. If not fall back to timestamps estimated in kernel.
* hid-sensor (light)
- Add a duplicate ID for the light channels so as to keep existing interface
whilst also using the more standard IIO interface.
* hts221
- acpi probing
* imx25-gcq
- Add a macro call to allow this driver to be automatically loaded.
* isl29028
- reorganise code to avoid deep nesting of if statements.
- move chip test and default regs into a function suitable or sharing with
power management code.
- tidy up some code alignment.
* lidar-lite-v3
- introduce compatible strings that make it clear Garmin have consideral
friends.
* mma8452
- avoid returning signed value when unsigned is appropriate
* spmi-vadc
- Update function for generic voltage conversion to take into account that
different channels on this device should be handled differently.
- Rework code to allow per channel voltage scaling and support the standard
options for this hardware.
- Fixup three minor issues with the above patches for this part. These all
effect test builds rather than the native builds for the part, but good to
clean them up anyway.
* st_sensors
- support device matching from the ACPI DST tables.
- acpi based probing for accelerometers
- acpi based probing for pressure sensors
- Allow pressure sensors to read negative values.
- Export sampling frequency for lps25h and lps331ap.
- Add support for the old DT bindings from the period when these deivces
were often supported through windows.
Docs fixup:
* typo in sysfs-bus-iio
According to the datasheet, the shortest available integration time for
ALS ADC conversion is 1.5625ms but illuminance_integration_time_available
sysfs file shows wrong value.
Cc: Crestez Dan Leonard <leonard.crestez@intel.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Fixes: d5d8f49b6 ("max44000: Expose ambient sensor scaling")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds a driver for the Capella Microsystems CM3605 Ambient
Light Sensor and proximity sensor. This is a pretty simple entirely
analog device that is interfaced with the target system using
the POUT (proximity out) and AOUT (ambient light out) signals.
The POUT signal is a simple high/low signal that indicates whether
an object is in proximity, most typically used to detect a face
in front of a mobile device. The signal requires that an infrared
LED is mounted next to the device, making IR light reflect off
the object in proximity and triggering the POUT signal. We grab
a GPIO pin to handle the POUT signal as an interrupt line and
register this as an event channel for the sensor.
Since the proximity sensor requires an IR LED, we add a LED trigger
named "cm3605" so that the infrared LED can just associate with
this trigger to be sure it is always on when the proximity sensor
needs it.
The AOUT is an analog voltage between 0 and 1550 mV that indicate
the LUX value in the ambient light: this is orthogonal to the
proximity sensor functionality. Since this analog voltage needs
to be converted into a digital value, the driver grabs an IIO
channel named "aout" associated with the device.
This patch created a combined ALS and proximity sensor driver.
The former supports raw reads of the LUX value and the latter
will generate proximity events.
To integrate this properly with Linux we also add a supply
regulator for the VDD pin (driving both functions) and add device
tree bindings to define the RSET resistor that in turn configures
the luminosity range of the ALS sensor.
Since the sensor needs to be on more or less constantly, we
restrict the power management to system suspend/resume: we
disable the IR LED and disable the regulator for VDD on suspend
and take them back up on resume.
Tests:
cd /sys/bus/iio/devices/iio:device1
cat in_illuminance_raw
304
(hold hand over sensor)
cat in_illuminance_raw
17
iio_event_monitor cm3605
Found IIO device with name cm3605 with device number 1
(hold hand over sensor)
Event: time: 2444842301447, type: proximity, channel: 0,
evtype: thresh, direction: falling
(remove hand over sensor)
Event: time: 2445583440706, type: proximity, channel: 0,
evtype: thresh, direction: rising
Cc: Capella Microsystems <capellamicro@gmail.com>
Cc: Kevin Tsai <ktsai@capellamicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
There is one light sensor type defined in the sensor hub specification,
which has one Illuminance field. It doesn't distinguish between ambient
light sensor or color sensor. Currently it is presented as IIO_INTENSITY
channel. There are some user spaces specifically looking for IIO_LIGHT
channel.
To satisfy such user spaces this change also add a duplicate IIO_LIGHT
channel. The units of measurement of Illuminance field is Lux, so it is
still compatible to IIO ABI.
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In function cm3232_reg_init(), it returns 0 even if the last call to
i2c_smbus_write_byte_data() returns a negative value (indicates error).
As a result, the return value may be inconsistent with the execution
status, and the caller of cm3232_reg_init() will not be able to detect
the error. This patch fixes the bug.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188641
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This array is supposed to have 10 elements. Smatch complains that with
the current code we can have n == max_ints and read beyond the end of
the array.
Fixes: ac4f6eee8f ("staging: iio: TAOS tsl258x: Device driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Move tsl2580, tsl2581, tsl2583 driver out of staging into mainline.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Driver was checking for direct mode but not locking it. Use
claim/release helper functions to guarantee the device stays
in direct mode during all raw write operations.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Driver was checking for direct mode but not locking it. Use
claim/release helper functions to guarantee the device stays
in direct mode during required raw read cases.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Move ISL29018/ISL29023/ISL29035 driver out of staging into mainline.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The si114x supports x=1,2,3 IR LEDs for proximity sensing together with
visible and IR ambient light sensing (ALS).
Newer parts (si1132, si1145/6/7) can measure UV light and compute an UV
index
This was tested on si1143 and si1145
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Here are a number of small driver fixes for 4.8-rc5.
The largest thing here is deleting an obsolete driver,
drivers/misc/bh1780gli.c, as the functionality of it was replaced by an
iio driver a while ago. The other fixes are things that have been
reported, or reverts of broken stuff (the binder change). All of these
changes have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlfK3/MPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspm5MAoLb+
VGesoc7cGbFN0EIskollZRzBAJ9Wnhvu3rVeDQYCA0t9+uRg0CcpWw==
=Wt/v
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a number of small driver fixes for 4.8-rc5.
The largest thing here is deleting an obsolete driver,
drivers/misc/bh1780gli.c, as the functionality of it was replaced by
an iio driver a while ago.
The other fixes are things that have been reported, or reverts of
broken stuff (the binder change). All of these changes have been in
linux-next for a while with no reported issues"
* tag 'char-misc-4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
thunderbolt: Don't declare Falcon Ridge unsupported
thunderbolt: Add support for INTEL_FALCON_RIDGE_2C controller.
thunderbolt: Fix resume quirk for Falcon Ridge 4C.
lkdtm: Mark lkdtm_rodata_do_nothing() notrace
mei: me: disable driver on SPT SPS firmware
Revert "android: binder: fix dangling pointer comparison"
drivers/iio/light/Kconfig: SENSORS_BH1780 cleanup
android: binder: fix dangling pointer comparison
misc: delete bh1780 driver
Commit 7ef9153d9a ("misc: delete bh1780 driver") has removed the
Kconfig option SENSORS_BH1780. Remove the last reference on this
option.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is likely that checking the result of 'pm_runtime_set_active' is
expected here.
Fixes: f0e5f57d3a ("iio: light: us8152d: Add power management support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Select IIO_BUFFER and IIO_TRIGGERED_BUFFER to compile.
Remove IIO_TRIGGER if present since IIO_BUFFER selects it.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
VCNL4000, VCNL4010 and VCNL4020 chips are fairly compatible from a software
point of view, added features are not yet supported by the driver
patch adds a check for the product ID and demotes the corresponding
dev_info() to dev_dbg()
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added macros for sensing range as the corresponding magic numbers
were used at multiple places.
- ISL29125_SENSING_RANGE_0 for 375 lux full range
- ISL29125_SENSING_RANGE_1 for 10k lux full range
Signed-off-by: Bijosh Thykkoottathil <bijosh.t@hotmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Adds a new per-device sysfs attribute "current_timestamp_clock" to allow
userspace to select a particular POSIX clock for buffered samples and
events timestamping.
Following clocks, as listed in clock_gettime(2), are supported:
CLOCK_REALTIME, CLOCK_MONOTONIC, CLOCK_MONOTONIC_RAW,
CLOCK_REALTIME_COARSE, CLOCK_MONOTONIC_COARSE, CLOCK_BOOTTIME and
CLOCK_TAI.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Acked-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Firstly some contact detail updates:
* NXP took over freescale. Update the mma8452 header to reflect this.
* Martin Kepplinger email address change in mma8452 header.
* Adriana Reus has changed email address. Update .mailmap.
* Matt Ranostay has changed email address. Update .mailmap.
New Device Support
* max1363
- add the missing i2c_device_ids for a couple of parts so they can actually
be used.
* ms5867
- add device ids for ms5805 and ms5837 parts.
New Features
* ad5755
- DT support. This one was a bit controversial and under review for a long
time. Still no one could come up with a better solution.
* stx104
- add gpio support
* ti-adc081c
- Add ACPI device ID matching.
Core changes
* Refuse to register triggers with duplicate names. There is no way to
distinguish between them so this makes no sense. A few drivers do not
generate unique names for each instance of the device present. We can't
fix this without changing ABI so leave them and wait for someone to
actually take the rare step of two identical accelerometers on the same
board.
* buffer-dma
- use ARRAY_SIZE in a few appropriate locations.
Tools
* Fix the fact that the --trigger-num option in generic_buffer didn't allow
0 which is perfectly valid in the ABI.
Cleanups
* as3935
- improve error reporting.
- remove redundant zeroing of a field in iio_priv.
* gp2ap020a00f
- use the iio_device_claim_*_mode helpers rather than open coding locking
around mode changes.
* isl29125
- use the iio_device_claim_*_mode helpers rather than open coding locking.
* lidar
- use the iio_device_claim_*_mode helpers rather than open coding locking.
* mma8452
- more detail in devices supported description in comments (addresses and
similar)
* sca3000
- add a missing error check.
* tcs3414
- use the iio_device_claim_*_mode helpers rather than open coding locking.
* tcs3472
- use the iio_device_claim_*_mode helpers rather than open coding locking.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=6Lja
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.8b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second round of new iio device support, features and cleanups in the 4.8 cycle
Firstly some contact detail updates:
* NXP took over freescale. Update the mma8452 header to reflect this.
* Martin Kepplinger email address change in mma8452 header.
* Adriana Reus has changed email address. Update .mailmap.
* Matt Ranostay has changed email address. Update .mailmap.
New Device Support
* max1363
- add the missing i2c_device_ids for a couple of parts so they can actually
be used.
* ms5867
- add device ids for ms5805 and ms5837 parts.
New Features
* ad5755
- DT support. This one was a bit controversial and under review for a long
time. Still no one could come up with a better solution.
* stx104
- add gpio support
* ti-adc081c
- Add ACPI device ID matching.
Core changes
* Refuse to register triggers with duplicate names. There is no way to
distinguish between them so this makes no sense. A few drivers do not
generate unique names for each instance of the device present. We can't
fix this without changing ABI so leave them and wait for someone to
actually take the rare step of two identical accelerometers on the same
board.
* buffer-dma
- use ARRAY_SIZE in a few appropriate locations.
Tools
* Fix the fact that the --trigger-num option in generic_buffer didn't allow
0 which is perfectly valid in the ABI.
Cleanups
* as3935
- improve error reporting.
- remove redundant zeroing of a field in iio_priv.
* gp2ap020a00f
- use the iio_device_claim_*_mode helpers rather than open coding locking
around mode changes.
* isl29125
- use the iio_device_claim_*_mode helpers rather than open coding locking.
* lidar
- use the iio_device_claim_*_mode helpers rather than open coding locking.
* mma8452
- more detail in devices supported description in comments (addresses and
similar)
* sca3000
- add a missing error check.
* tcs3414
- use the iio_device_claim_*_mode helpers rather than open coding locking.
* tcs3472
- use the iio_device_claim_*_mode helpers rather than open coding locking.
We want the fixes in here, and we can resolve a merge issue in
drivers/iio/industrialio-trigger.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the code that guarantees the device stays in direct mode
with iio_device_claim_direct_mode() which does same. Includes a
tiny bit of refactoring (single case -> if) and simplified return
flow.
Also prevents a theoretical race condition by effectively taking the lock
a little earlier than before.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Replace the code that guarantees the device stays in direct mode
with iio_device_claim_direct_mode() which does same. This allows
removal of an unused lock in the device private global data.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Replace the code that guarantees the device stays in direct mode
with iio_device_claim_direct_mode() which does same. This allows
removal of an unused lock in the device private global data.
Also prevents a previous race condition when a buffer is enabled whilst
a raw read is going on.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Replace the code that guarantees the device stays in direct mode
with iio_device_claim_direct_mode() which does same. This allows
removal of an unused lock in the device private global data.
Also prevents a possible race around a buffer being enabled whilst
a read is going on.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
New device support
* ads1015
- add ads1115 support
* bma220 accelerometer
- new driver
- triggered buffer support.
* bmc150
- add bmm150 support.
* bmp280
- bme280 support with addition of humidity channel.
* max5487 potentiometer
- new driver
* MMA7660FC accelerometer.
- New driver
* st-pressure
- support for the lps22hb
* loop trigger.
- This one is *nasty* but we have real applications (parrot drones) where
it is useful. The trigger basically spins as hard as it can firing off
a new trigger each time all triggered devices come back to say they are
done. It doesn't hang a machine even when doing it on a dummy driver.
A lot nicer than having this implemented within lots of device drivers
anyway.
Core stuff
* Add support to create IIO devices via configfs (similar to we did for
triggers a while back) + docs.
* New channel types
- IIO_ELECTRICAL_CONDUCTIVITY
* Couple of MAINTAINERS patches to list the device tree bindings.
* Make trigger ops structure non optional (comment fix). It hasn't been for
an awful long time, but that's not what the description said.
New features
* ak8975
- support adapters that are limited to byte data only by allowing the
emulated block read i2c function that was recently introduced.
* atlas-ph
- support atlas-ec (electrical conductivity sensor)
* bmi160
- add available frequency and scale attributes to make the driver
more user friendly (and avoid having to read the datasheet to know
what will work).
* dummy
- move creation to configfs interface. It's not real hardware so we
are not that worried about the ABI breakage ;)
* mma8452
- oversampling ration support
* nau7802
- expose available gains to make life easier for userspace.
* st-sensors
- allow use of emulation for SMBus block reads as all the st parts support
it.
* ti-ads1015
- list datasheet names to allow their use by inkernel consumers.
* Various module alias additions to help auto probing. Drop one redundant one
as well.
Cleanups
* ad7266, ad7476, ad7887, ad7923, ad799x
- use direct mode claim function rather than open coding it during sensor
read (prevents switching on buffers mid read).
* ad7793, ad7791
- use direct mode claim to prevent frequency changes when buffers running.
* afe440x - These are ABI breaking but the driver requires custom userspace
code to do anything useful anyway and that is still being written and under
control of TI. Ultimately we may have other libraries to do pulse
oximetry with these devices but we aren't aware of any yet.
- kernel-doc format fixes
- drop ifdef fun around of_match_ptr - it's not worth the mess to save
a tiny amount of space.
- drop some unnecessary register initializations.
- drop the weird locked gain modes as they gain us nothing (can just set
all gains separately).
- remove handling of offset attributes seeing as no channels actually have
them (oops)
- Drop the LED3 input channel as it's an alias for ALED2.
- *big one* remove channel names - an experiment that turned out to not
make sense - see patch for details.
- use regmap fields to clean up code.
- tie the tia gain stages to appropriate channels in the ABI as that is
what they really effect. Same with the LED currents.
- cleanout some unused defines and fix a missnamed one.
* atlas-ph
- reorganise to allow support of other similar parts.
* bmc150
- document supported chips in kconfig help.
* jsa1212
- drop an unneeded i2c functionality check for functionality the driver
doesn't use.
* mxs-lradc
- simply touch screen registration code.
- remove the touch screen unregister as all devm based now.
- disable only those channels that are masked in hardware stop (others
are already dealt with elsewhere)
* st-sensors
- unexport st_sensors_get_buffer_element as nothing outside the st-sensors
core driver uses it.
- fix handling of failure to start up regulators.
* tpl0102
- drop an i2c functionality test for features that aren't needed.
* ti-am335x
- use variable name rather than type in sizeof for clarity.
- use SIMPLE_DEV_PM_OPS helper macro to tidy up a bit.
Tools
* Add install / uninstall to makefile. Someone cares, so presumably
some people will find it useful!
* generic_buffer
- rename to iio_generic_buffer to line up with other tools.
- handle cleanup when receiving signals
- Add a --device-num option and a --trigger-num option rather than
relying on naming which doesn't work if you have two of the same part.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Hq1a
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.8a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of IIO new device support, features and cleanups for the 4.8 cycle.
New device support
* ads1015
- add ads1115 support
* bma220 accelerometer
- new driver
- triggered buffer support.
* bmc150
- add bmm150 support.
* bmp280
- bme280 support with addition of humidity channel.
* max5487 potentiometer
- new driver
* MMA7660FC accelerometer.
- New driver
* st-pressure
- support for the lps22hb
* loop trigger.
- This one is *nasty* but we have real applications (parrot drones) where
it is useful. The trigger basically spins as hard as it can firing off
a new trigger each time all triggered devices come back to say they are
done. It doesn't hang a machine even when doing it on a dummy driver.
A lot nicer than having this implemented within lots of device drivers
anyway.
Core stuff
* Add support to create IIO devices via configfs (similar to we did for
triggers a while back) + docs.
* New channel types
- IIO_ELECTRICAL_CONDUCTIVITY
* Couple of MAINTAINERS patches to list the device tree bindings.
* Make trigger ops structure non optional (comment fix). It hasn't been for
an awful long time, but that's not what the description said.
New features
* ak8975
- support adapters that are limited to byte data only by allowing the
emulated block read i2c function that was recently introduced.
* atlas-ph
- support atlas-ec (electrical conductivity sensor)
* bmi160
- add available frequency and scale attributes to make the driver
more user friendly (and avoid having to read the datasheet to know
what will work).
* dummy
- move creation to configfs interface. It's not real hardware so we
are not that worried about the ABI breakage ;)
* mma8452
- oversampling ration support
* nau7802
- expose available gains to make life easier for userspace.
* st-sensors
- allow use of emulation for SMBus block reads as all the st parts support
it.
* ti-ads1015
- list datasheet names to allow their use by inkernel consumers.
* Various module alias additions to help auto probing. Drop one redundant one
as well.
Cleanups
* ad7266, ad7476, ad7887, ad7923, ad799x
- use direct mode claim function rather than open coding it during sensor
read (prevents switching on buffers mid read).
* ad7793, ad7791
- use direct mode claim to prevent frequency changes when buffers running.
* afe440x - These are ABI breaking but the driver requires custom userspace
code to do anything useful anyway and that is still being written and under
control of TI. Ultimately we may have other libraries to do pulse
oximetry with these devices but we aren't aware of any yet.
- kernel-doc format fixes
- drop ifdef fun around of_match_ptr - it's not worth the mess to save
a tiny amount of space.
- drop some unnecessary register initializations.
- drop the weird locked gain modes as they gain us nothing (can just set
all gains separately).
- remove handling of offset attributes seeing as no channels actually have
them (oops)
- Drop the LED3 input channel as it's an alias for ALED2.
- *big one* remove channel names - an experiment that turned out to not
make sense - see patch for details.
- use regmap fields to clean up code.
- tie the tia gain stages to appropriate channels in the ABI as that is
what they really effect. Same with the LED currents.
- cleanout some unused defines and fix a missnamed one.
* atlas-ph
- reorganise to allow support of other similar parts.
* bmc150
- document supported chips in kconfig help.
* jsa1212
- drop an unneeded i2c functionality check for functionality the driver
doesn't use.
* mxs-lradc
- simply touch screen registration code.
- remove the touch screen unregister as all devm based now.
- disable only those channels that are masked in hardware stop (others
are already dealt with elsewhere)
* st-sensors
- unexport st_sensors_get_buffer_element as nothing outside the st-sensors
core driver uses it.
- fix handling of failure to start up regulators.
* tpl0102
- drop an i2c functionality test for features that aren't needed.
* ti-am335x
- use variable name rather than type in sizeof for clarity.
- use SIMPLE_DEV_PM_OPS helper macro to tidy up a bit.
Tools
* Add install / uninstall to makefile. Someone cares, so presumably
some people will find it useful!
* generic_buffer
- rename to iio_generic_buffer to line up with other tools.
- handle cleanup when receiving signals
- Add a --device-num option and a --trigger-num option rather than
relying on naming which doesn't work if you have two of the same part.
Without this, the iio:deviceX is missing in the /sys/bus/i2c/devices/0-0039
Some userspace tools use this path to identify a specific instance of the
device.
Signed-off-by: Yong Li <sdliyong@gmail.com>
Reviewed-By: Matt Ranostay <mranostay@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Using the struct i2c_device->id field for naming the light sensor
is a bad idea: when booting from the pure device tree this is NULL
and that causes the device not to have the "name" property in
sysfs and that in turn confuses the "lsiio" command to stop listing
devices.
So instead of using the device .id, use the hard string "bh1780",
which works just fine.
Fixes: 1f0477f183 ("iio: light: new driver for the ROHM BH1780")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The code in runtime_[suspend|resume] was assuming that the
i2c client data was the bh1780 state container, but it contains
the IIO device. So first dereference the IIO device from the
i2c client, then get the state container using the iio_priv()
call.
Fixes: 1f0477f183 ("iio: light: new driver for the ROHM BH1780")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This is not implemented and doesn't really make sense because IIO
proximity is unit-less.
Remove IIO_CHAN_INFO_SCALE from info_mask because so that the _scale
sysfs entry won't appear. This fixes userspace tools like generic_buffer
which abort when reads returns an error.
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This driver does not call i2c_smbus_read|write_byte_data(),
so remove the corresponding functionality test. It uses regmap
to handle byte transfers transparently.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Reviewed-by:Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Matt Ranostay <matt.ranostay@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When writing a value using direct reg access from debugfs
we need to return and not fall through to reading the
value, lest we'll dereference a NULL pointer.
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Bit of a bumper set for new drivers but plenty of other stuff here as well!
New device support
* ad5592R ADC/DAC
- new driver supporting ad5592r and ad5593r combined ADC/DAC and gpio chips.
* Aosong am2315 relative humidity
- new driver with triggered buffer support in follow up patch.
* bmi160 imu
- new driver
* bmp280
- bmp180 support - note there is support in the misc/bmp085 driver. Intent
is to remove that driver long term.
* invensense mpu6050
- cleanup leading to explicit support of mpu9150 with a good few cleanups
along the way.
* Hope RF hp03 pressure and temperature sensor.
- new driver
* maxim DS1803 potentiometer
- new driver
* maxim max44000 light and proximity sensor
- new driver built in a series of steps to support pretty much everything.
* ROHM BH1780 light sensor
- new driver. There is an existing driver in misc that this is pretty much
intended to replace. The discussion on whether to support the non standard
interface of that driver is some way is continuing.
* st-gyro
- lsm9ds0-gyro. The accel/magn side of this will take a while longer as
extensions to the st library are needed for cases where two types of sensor
share a single i2c address.
* ti-adc081c
- support the adc101c and adc121c
* Vishay VEML6070 UV sensor
- new driver.
New features
* core
- devm_ APIs for channel_get and channel_get_all. The first user of these
is the generic ADC based thermal driver. As it is going through the
thermal tree these will be picked up as a patch to that next cycle as that
is how the author preferred to do it.
- mounting matrix support. This new core support allows devices to provide
to userspace (typically from the device tree) allowing compensation for how
the sensor is mounted on the device. First examples are on UAVs but it
has a more mundane use on typical phone where the chip may be on the front
or the back of the circuit board and soldered at any angle. Includes
support for this ABI in ak8975 (which has an older interface, now
deprecated) and mpu6050.
* tools
- add a -a option to enable all available channels in generic_buffer sample.
Makes it somewhat easier to use.
* adis library and drivers
- support manual self test flag clearing. This has technically been broken
for a very long time - result is an offset on readings as the applied field
is on all the time.
* ak8975
- triggered buffer support
* bmc150
- spi support (including splitting the driver into core and i2c parts)
* bmp280
- oversampling support.
* dht11
- improved logging - useful to debug timing issues on this quirky device.
* st-sensors
- read each channel invidivually as not all support the optimization of
reading in bulk. This is technically a fix, but will need to be backported
if desired.
- support open drain and shared interrupts.
* ti-adc081c
- triggered buffer support.
Cleanups
* inkern
- white space fix.
* ad7606
- use the iio_device_claim_direct_mode call rather than open coding equiv.
* ad799x
- white space fix.
* ad9523
- unsigned -> unsigned int
* apds9660
- brace location tidying up.
- silence an uninitialized variable warning.
* ak8975
- else and brace on same line fix.
* at91_adc
- white space fixes.
* bmc150
- use regmap stored copy of the device pointer rather than having an
additional copy.
* bmg160
- use regmap stored copy of the device pointer rather than having an
additional copy.
* hid-sensors
- white space fixes.
* mcp3422
- white space fix.
* mma7455
- use regmap to retrieve the device struct rather than carrying another copy
in the private data.
* ms_sensors
- white space fix.
* mxs-lradc
- move current bindings out of staging - some will be shortly deprecated but
the reality is that we have device trees out there using them so they will
need to be supported for some time. They accidentally got left behind
when the driver graduated from staging.
- white space cleanup.
- set INPUT_PROP_DIRECT.
- move ts config into a better function.
- move the STMP reset out of the ADC init.
* vf610_adc
- case label indenting fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=zzV9
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.7b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-testing
Jonathan writes:
2nd set of new device support, features and cleanup for IIO in the 4.7 cycle.
Bit of a bumper set for new drivers but plenty of other stuff here as well!
New device support
* ad5592R ADC/DAC
- new driver supporting ad5592r and ad5593r combined ADC/DAC and gpio chips.
* Aosong am2315 relative humidity
- new driver with triggered buffer support in follow up patch.
* bmi160 imu
- new driver
* bmp280
- bmp180 support - note there is support in the misc/bmp085 driver. Intent
is to remove that driver long term.
* invensense mpu6050
- cleanup leading to explicit support of mpu9150 with a good few cleanups
along the way.
* Hope RF hp03 pressure and temperature sensor.
- new driver
* maxim DS1803 potentiometer
- new driver
* maxim max44000 light and proximity sensor
- new driver built in a series of steps to support pretty much everything.
* ROHM BH1780 light sensor
- new driver. There is an existing driver in misc that this is pretty much
intended to replace. The discussion on whether to support the non standard
interface of that driver is some way is continuing.
* st-gyro
- lsm9ds0-gyro. The accel/magn side of this will take a while longer as
extensions to the st library are needed for cases where two types of sensor
share a single i2c address.
* ti-adc081c
- support the adc101c and adc121c
* Vishay VEML6070 UV sensor
- new driver.
New features
* core
- devm_ APIs for channel_get and channel_get_all. The first user of these
is the generic ADC based thermal driver. As it is going through the
thermal tree these will be picked up as a patch to that next cycle as that
is how the author preferred to do it.
- mounting matrix support. This new core support allows devices to provide
to userspace (typically from the device tree) allowing compensation for how
the sensor is mounted on the device. First examples are on UAVs but it
has a more mundane use on typical phone where the chip may be on the front
or the back of the circuit board and soldered at any angle. Includes
support for this ABI in ak8975 (which has an older interface, now
deprecated) and mpu6050.
* tools
- add a -a option to enable all available channels in generic_buffer sample.
Makes it somewhat easier to use.
* adis library and drivers
- support manual self test flag clearing. This has technically been broken
for a very long time - result is an offset on readings as the applied field
is on all the time.
* ak8975
- triggered buffer support
* bmc150
- spi support (including splitting the driver into core and i2c parts)
* bmp280
- oversampling support.
* dht11
- improved logging - useful to debug timing issues on this quirky device.
* st-sensors
- read each channel invidivually as not all support the optimization of
reading in bulk. This is technically a fix, but will need to be backported
if desired.
- support open drain and shared interrupts.
* ti-adc081c
- triggered buffer support.
Cleanups
* inkern
- white space fix.
* ad7606
- use the iio_device_claim_direct_mode call rather than open coding equiv.
* ad799x
- white space fix.
* ad9523
- unsigned -> unsigned int
* apds9660
- brace location tidying up.
- silence an uninitialized variable warning.
* ak8975
- else and brace on same line fix.
* at91_adc
- white space fixes.
* bmc150
- use regmap stored copy of the device pointer rather than having an
additional copy.
* bmg160
- use regmap stored copy of the device pointer rather than having an
additional copy.
* hid-sensors
- white space fixes.
* mcp3422
- white space fix.
* mma7455
- use regmap to retrieve the device struct rather than carrying another copy
in the private data.
* ms_sensors
- white space fix.
* mxs-lradc
- move current bindings out of staging - some will be shortly deprecated but
the reality is that we have device trees out there using them so they will
need to be supported for some time. They accidentally got left behind
when the driver graduated from staging.
- white space cleanup.
- set INPUT_PROP_DIRECT.
- move ts config into a better function.
- move the STMP reset out of the ADC init.
* vf610_adc
- case label indenting fix.
This patch exposes ALSTIM as illuminance_integration_time and ALSPGA as
illuminance_scale.
Changing ALSTIM also changes the number of bits available in the data
register. This is handled inside raw value reading because:
* It's very easy to shift a few bits
* It allows SCALE and INT_TIME to be completely independent controls
* Buffer support requires constant scan_type.realbits per-channel
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This is exposed as an output channel with "led" as an extend_name.
Other sensors also have support for controlling an external LED. It's
not clear that simply exposing an undecorated output channel is the
correct approach.
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The proximity sensor relies on sending pulses to an external IR led and
it is disabled by default on powerup. The driver will enable it with a
default power setting.
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This just adds support for reporting illuminance with default settings.
Important default registers are written on probe because the device
otherwise lacks a reset function.
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
It causes a static checker warning if we use "buf" on the failure path
so move that inside the if statement.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
ultraviolet (UV) light sensor with I2C interface with a peak
sensitivity at 355 nm
strangely, chip uses two addresses 0x38 and 0x39 for LSB and
MSB data, resp.
datasheet: http://www.vishay.com/docs/84277/veml6070.pdf
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This is a reimplementation of the old misc device driver for the
ROHM BH1780 ambient light sensor (drivers/misc/bh1780gli.c).
Differences from the old driver:
- Uses the IIO framework
- Uses runtime PM to idle the hardware after 5 seconds
- No weird custom power management from userspace
- No homebrewn values in sysfs
This uses the same (undocumented) device tree compatible-string
as the old driver ("rohm,bh1780gli").
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes the error reported by checkpatch.pl:
ERROR: that open brace { should be on the previous line
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This resolves a lot of merge issues with PAGE_CACHE_* changes, and an
iio driver merge issue.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Again I've ended up with two early fix sets, depending on whether they are
dependent on elements of the merge window or simply came in after I had
patches with that dependency already, vs older fixes that were just too
late for the last cycle. This first set is for the older ones.
- max1353
* Add a missing adc to max1363_id - the driver has supported the
max11644-11647 for a while, but as they weren't in the id table there
was no way of actually initializing it.
* Fix a wrong reference voltage for the above models. Given you couldn't
initialize the driver for these parts without patching, no one noticed
that the reference voltage used in computing the scaling was wrong.
- apds9960
* The fifo last enelement was read twice (and hence pushed out twice) due
to a small logic bug.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJXAXr7AAoJEFSFNJnE9BaItS0P/2wAnYTMEU67ja9SSu6Z2oeU
rxDesnKm0g/coa1+nx42lb8fXfYQKCb57o234fq9odKKuc1g7K77Fdaf3/bv8HD6
sPbDqHx66yk5iYPAAOn8pAYpB6GPzhN5xLE7oJzuHs/qLuUn36G09PL1lo1sdVdF
3wT7U3bOgdaRcQyxQJ6zR229Vq9kgG1RHYeqFzooO/Al+IgfCW5F3MNJWKUr4UpP
IHyusbpH5vjVMTqs1WNmcT3q7miFGl8FeEFVFXFv7rjrYD24Zvl+CiZTA8zyai0/
kOF1ptsw3WuxTfshTMiv7PX0HzNerPrRCIXqoNjpN++k234K+mDU/hjeACoRe5jH
ud4zxkOx7ssmPk8xh5U9ICD+AFcFVrhpVQq6esqkukaYA/CXGbY99e9p0TRH/7T7
I/53xBnesyCPPV5ppr5J7Mbgzd4jdVsQN+Cj5aVpTyg2PkP+WqM2xx9nEfrfcg1T
RCv02PFZFrZsECRT35pOmbM5FMnU83sW5CZak11I5cHMEDPU+TCq89H226ppHP2O
3HwGB+s473whNfRBPrVGcTZSx71li3orv4XNYX3wFNMLdWXzIDlGlWk52I3NqKwi
GEdYvsdKjFoTho/nWgxyw/Nqqj9wtrCznbvSCnWwJf9a0AxdzKurFCygfKoCskAC
XcdojNMWdwLH4twvPT7z
=Bfg6
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.6a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into usb-linus
Jonathan writes:
First round of IIO fixes for the 4.6 cycle.
Again I've ended up with two early fix sets, depending on whether they are
dependent on elements of the merge window or simply came in after I had
patches with that dependency already, vs older fixes that were just too
late for the last cycle. This first set is for the older ones.
- max1353
* Add a missing adc to max1363_id - the driver has supported the
max11644-11647 for a while, but as they weren't in the id table there
was no way of actually initializing it.
* Fix a wrong reference voltage for the above models. Given you couldn't
initialize the driver for these parts without patching, no one noticed
that the reference voltage used in computing the scaling was wrong.
- apds9960
* The fifo last enelement was read twice (and hence pushed out twice) due
to a small logic bug.
David Heidelberg