As of kernel 4.10, ALSA dice driver is expected to be used in default
speed. In most cases, it's S400. While, IEEE 1394 specification describes
the other speed such as S800.
According to 'TCD30XX User Guide', its link layer controller supports
several transmission speed up to S800[0]. In Dice software interface,
transmission speed in output direction can be configured by asynchronous
transaction to 'TX_SPEED' offset in its address space. S800 may be
available.
This commit improves configuration of transmission unit before starting
packet streaming for this purpose. The value of 'max_speed' in 'fw_device'
data structure has available maximum speed decided in bus arbitration,
thus it's within capacity of the unit.
[0] TCD3xx User Guide - TCAT 1394 LLC, Revision 0.9.0-41360 (TC Applied Technologies, May 6 2015)
http://www.tctechnologies.tc/index.php/support/support-hardware/dice-iii-detailed-documentation
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When sound card is going to be released, dice private data is
also released. Then all of data should be released. However,
stream data is not released. This causes memory leak when
unplugging dice unit.
This commit fixes the bug.
Fixes: 4bdc495c87b3('ALSA: dice: handle several PCM substreams when any isochronous streams are available')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In dice interface, two blocks of register are accessible via IEEE 1394
asynchronous transaction to represent the number of supported isochronous
streams and the number of quadlets for stream information.
Current ALSA dice driver uses array with 'unsigned int' element for
temporary cache of these information. But using structure is preferable
for begin easily comprehensible.
This commit applies a local structure for this aim.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit enables ALSA dice driver to handle whole available streams.
In Dice, certain registers represent the number of available streams at
current sampling transfer frequency for both directions. The parameters
of each stream are represented in a block of register. This block is
aligned sequentially. These streams start simultaneously by writing
enable bit to a register.
This commit operates these registers when starting/stopping streams.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently ALSA dice driver handles a pair of isochronous resources for
IEC 61883-1/6 packet streaming. While, according to some documents about
ASICs named as 'Dice', several isochronous streams are available.
Here, I start to describe ASICs produced under 'Dice' name.
* Dice II (designed by wavefront semiconductor, including TCAT's IP)
* STD (with limited functionality of DTCP)
* CP (with full functionality of DTCP)
* TCD2210/2210-E (so-called 'Dice Mini')
* TCD2220/2220-E (so-called 'Dice Jr.')
* TCD3070-CH (so-called 'Dice III')
Some documents are public and we can see hardware design of them. We can
find some articles about hardware internal register definitions
(not registers exported to IEEE 1394 bus).
* DICE II User Guide
* http://www.tctechnologies.tc/archive/downloads/dice_ii_user_guide.pdf
* 6.1 AVS Audio Receivers
* Table 6.1: AVS Audio Receiver Memory Map
* ARX1-ARX4
* 6.2 AVS Audio Transmitters
* Table 6.2: AVS Audio Transmitter Memory Map
* ATX1, ATX2
* TCD22xx User Guide
* http://www.tctechnologies.tc/downloads/tcd22xx_user_guide.pdf
* 6.1 AVS Audio Receivers
* Table 66: AVS Audio Receiver Memory Map
* ARX1, ARX2
* 6/2 AVS Audio Transmitters
* Table 67: AVS Audio Transmitter Memory Map
* ATX1, ATX2
* DICE III
* http://www.tctechnologies.tc/downloads/TCD3070-CH.pdf
* Dual stream 63 channel transmitter/receiver
For Dice II and TCD22xx series, maximum 16 data channels are transferred in
an AMDTP packet, while for Dice III, maximum 32 data channels are
transferred.
According to the design of the series of these ASICs, this commit allows
this driver to handle additional set of isochronous resources. For
practical reason, two pair of isochronous resources are added. As of this
commit, this driver still use a pair of the first isochronous resources.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit drops implementation of duplex streams synchronization
from ALSA dice driver, due to a reason of hardware design. This patch
allows dice-based units to generate sounds correctly when isochronous
packet streaming starts at first time.
In IEC 61883-6:2005, CIP packetization layer for AM824 data format
utilizes the value of SYT field in CIP header of received packet for
a reference to phase lock loop. Figure 3 in clause 4.3 describes it.
The value is an offset from cycle_time field of every cycle start packet
from cycle master on IEEE 1394 bus. The time calculated with these two
fields is called as 'presentation timestamp' which represents the time
to play data included in the packet.
Although, this idea includes some problems due to accuracy of timekeep in
cycle master, accuracy of transmission of cycle start packet on the bus
with the other units, accuracy of sampling clock in data transmitter side
and accuracy of replay in data receiver side. In most case, these
accuracies somewhat worse because there's no such ideal hardwares in this
world.
For the issues, ASICs for Dice include Jitter Elimination Technologies
(JET) PLL. The PLL can handle several sources of clock and compensate it
with high-precision internal clock source. The sequence of value in syt
field of received AMDTP packets is one of the sources, therefore
transmitters on IEEE 1394 bus should transfer it.
On the other hand, current ALSA dice driver is programmed with a mode of
duplex streams with synchronization. In this mode, the driver outputs
packets after some incoming packets are handled, to re-use the value of
SYT field in incoming packets to the value for outgoing packets. This mode
is enabled when source signal of sampling clock is set to internal, and
this is a major use case. Thus, in most cases, the unit receives no packets
during a short time after packet streaming starts.
As long as I experienced, this causes the units to generate no sounds at
first time to receive packets. This issue occurs only with Dice II. I guess
this is due to a quirk of the PLL. In short, the PLL cannot generate firm
signals to ADCs/DACs or the other ICs when no packets are received in the
beginning of packet streaming. While, on second time or later, the unit
generates sound correctly. I guess that starting packet streaming at first
time sets the PLL correctly.
Well, still based on my hypothesis and no way to prove it, this commit
drops duplex streams synchronization from this driver. At least, the PLL
requires the sequence of value in SYT field of received AMDTP packets as
one of source of clock signals with internal clock source.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As long as I tested, Dice-based models produced by TC Electronic with
factory-configured settings transfer no notification within
ensure_phase_lock(). On the other hand, with upgraded firmwares, it
starts to transfer the notification. This seems to be a quirk of earlier
firmwares.
This commit ensures phase lock by reading a register after waiting for
the notification. Even if it's timed-out, ensure_phase_lock() return
success as long as the register has expected clock status.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In former commits, probing process has no need to set sampling transfer
frequency. Although it's OK to drop a function to change the frequency
from this module, some models require it before streaming. This seems to
be due to phase lock of clock source.
This commit moves the function from transaction layer to stream layer, and
rename it according to the purpose.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dice interface design doesn't allow drivers to read supported combination
between sampling transfer frequencies and the number of Multi bit linear
audio data channels. Due to the design, ALSA dice driver changes current
sampling transfer frequency to generate cache of the combinations at
device probing processing.
Although, this idea is worse because ALSA dice driver changes the state of
clock. This is not what users want when they save favorite configuration
to the device in advance.
Furthermore, there's a possibility that the format of data block is decided
not only according to current sampling transfer frequency, but also the
other factors, i.e. data format for digital interface. It's not good to
generate channel cache according to the sampling transfer frequency only.
This commit purges processing cache data and related structure members. As
a result, users must set preferable sampling transfer frequency before
using ALSA PCM applications, as long as they want to start any PCM
substreams at the rate except for current one.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In previous commit, ALSA Dice driver limits PCM substreams at current
sampling transfer frequency and current number of Multi bit linear audio
data channel. Thus, the driver has no need to start AMDTP streams at
the other sampling transfer frequency except for current one. This is due
to Dice interface design.
This commit limits AMDTP stream at current sampling transfer frequency,
according to the design.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some local variables in some functions are typed as unsigned int, while
__be32 value is assigned to them. This causes sparse warnings.
dice-stream.c:50:17: warning: incorrect type in assignment (different base types)
dice-stream.c:50:17: expected unsigned int [unsigned] channel
dice-stream.c:50:17: got restricted __be32 [usertype] <noident>
dice-stream.c:74:17: warning: incorrect type in assignment (different base types)
dice-stream.c:74:17: expected unsigned int [unsigned] channel
dice-stream.c:74:17: got restricted __be32 [usertype] <noident>
This commit fixes this bug.
Fixes: 288a8d0cb04f('ALSA: dice: Change the way to start stream')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In IEC 61883-6, several types of data are available in AM824 format. The
data is transferred in each data channel. The position of data channel in
data block differs depending on model.
Current implementation has an array to map the index of data channel in an
data block to the position of actual data channel. The implementation
allows each driver to access the mapping directly.
In later commit, the mapping is in specific structure pushed into an
opaque pointer. Helper functions are required.
This commit adds the helper functions for this purpose. In IEC 61883-6,
AM824 format supports many data types, while this specification easily
causes over-engineering. Current AM824 implementation is allowed to handle
two types of data, Multi Bit Linear Audio data (=PCM samples) and MIDI
conformant data (=MIDI messages).
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The value of FDF field in CIP header is protocol-dependent. Thus, it's
better to allow data block processing layer to decide the value in any
timing.
In AM824 data format, the value of FDF field in CIP header indicates
N-flag and Nominal Sampling Frequency Code (sfc). The N-flag is for
switching 'Clock-based rate control mode' and 'Command-based rate control
mode'. In our implementation, 'Clock-based rate control mode' is just
supported. Therefore, When sampling transfer frequency is decided, then
the FDF can be set.
This commit replaces 'amdtp_stream_set_parameters' with
'amdtp_am824_set_parameters' to set the FDF. This is the same timing
to decide the ration between the number of data blocks and the number of
PCM frames.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds data block processing layer for AM824 format. The new
layer initializes streaming layer with its value for fmt field.
Currently, most implementation of data block processing still remains
streaming layer. In later commits, these codes will be moved to the layer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In IEC 61883-6, one data block represents one event. In ALSA, the event is
one PCM frame. Therefore, when processing one data block, current
implementation counts one PCM frame.
On the other hand, Dice platform has a quirk called as 'dual wire' at
higher sampling rate. In detail, see comment of commit 6eb6c81eee
("ALSA: dice: Split stream functionality into a file").
Currently, to handle this quirk, AMDTP stream structure has a
'double_pcm_frames' member. When this is enabled, two PCM frames are
counted. Each driver set this flag by accessing the structure member
directly.
In future commit, some members related to AM824 data block will be moved
to specific structure, to separate packet streaming layer and data block
processing layer. The access will be limited by opaque pointer.
For this reason, this commit adds an argument into
amdtp_stream_set_parameter() to set the flag.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, amdtp_stream_set_parameters() returns no error even if wrong
arguments are given. This is not good for streaming layer because drivers
can continue processing ignoring capability of streaming layer.
This commit changes this function to return error code.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently stream destructor in each driver has a problem to be called in
a context in which sound card object is released, because the destructors
call amdtp_stream_pcm_abort() and touch PCM runtime data.
The PCM runtime data is destroyed in application's context with
snd_pcm_close(), on the other hand PCM substream data is destroyed after
sound card object is released, in most case after all of ALSA character
devices are released. When PCM runtime is destroyed and PCM substream is
remained, amdtp_stream_pcm_abort() touches PCM runtime data and causes
Null-pointer-dereference.
This commit changes stream destructors and allows each driver to call
it after releasing runtime.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org> # 3.19+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a support for MIDI capture/playback
When MIDI substrams already start streaming and PCM substreams are going to
join at different sampling rate, streams are stopped once. Then sampling rate
is changed and streams are restarted.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit allows this driver to handle devices with non SYT-Match
sampling clock source.
When sampling clock source is SYT-Match mode, devices handle
'presentation timestamp' in received packets and generates sampling clock
according to the information. In this case, driver is synchronization master
and must transfer correct value in SYT field of each packets in outgoing
stream, then the outgoing stream is a master stream.
On the other hand, non SYT-Match mode, devices do this. So drivers must pick
up the value in SYT field of incoming packets and use the value for outgoing
stream. Currently firewire-lib module achieve this work.
Furthermore, without SYT-Match and internal clock source, the sampling rate
should be fixed for the other devices connected to the handled device. This
commit add a restriction of sampling rate at this situation.
With these implementations, this driver has no need to set clock source.
This commit remove set function.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds support for AMDTP in-stream. As a result, Dice driver
supports full duplex streams with synchronization.
AMDTP can transfer timestamps in its packets. By handling the timestamp,
devices can synchronize to the other devices or drivers on the same bus.
When Dice chipset is 'enabled', it starts streams with correct settings.
This 'enable' register is global, thus, when a stream is started to run,
an opposite stream can't start unless turning off 'enable'. Therefore
a pair of streams must be running. This causes a loss of CPU usage when
single stream is needed for neither playbacking or capturing.
This commit assumes that playback-only models also have a functionality
to transmit stream for delivering timestamps.
Currently, sampling clock source is restricted to SYT-Match mode. This is
improved in followed commit. I note that at SYT-Match mode, Dice can select
from 4 streams for synchronization but this driver uses the 1st stream only
for simplicity.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Streaming functionality can start streams when rate is given but currently
some codes are in PCM functionality.
This commit changes the way to start stream and add some arrangement
to make it easy to understand the way.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a file and move some codes related to PCM functionality.
Currently PCM playback is supported. PCM capture will be supported in followed
commits.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a file with some helper functions for streaming, and move some
codes into the file with some arrangements.
Well-known CMP is not used to start/stop streams for Dice chipset. It's
achieved by writing to specific address. We call this way as 'enable'.
When devices are 'enabled', streaming starts in registered isochronous channel.
Some helper functions are already implemented in previous commit.
Basically, the stream is compliant to IEC 61883-6, so-called as AMDTP. But Dice
has a specific quirk, so called-as 'Dual Wire'. This quirk is applied at
176.4/192.0kHz. In this mode, each packet includes double number of events than
number in the specification, and stream runs at a half of sampling rate.
There is another quirk at bus reset. Dice chipset handles drivers' request but
don't re-enable streaming. So stream should be stopped.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Sakamoto