The A31 companion pmic (axp221) does not generate vbus change interrupts
when the board is driving vbus, so we must poll when using the pmic for
vbus-det _and_ we're driving vbus.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
commit 5cf700ac9d ("phy: phy-sun4i-usb: Fix optional gpios failing
probe")
changed the condition under which irqs are requested, but omitted matching
changes to sun4i_usb_phy_remove(). This commit fixes this.
Fixes: 5cf700ac9d ("phy: phy-sun4i-usb: Fix optional gpios failing probe")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The interrupt 0 is not a valid interrupt number. In the event where the
retrieval of the vbus-det gpio would return null, the gpiod_to_irq
callback would return 0, while the current code makes the assumption
that it is a valid interrupt, and would go on calling request_irq.
Obviously, this would fail, preventing the driver from probing properly,
while the vbus and id gpios are optional.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Note this commit only adds support for phys 1-3, phy 0, the otg phy, is
not yet (fully) supported after this commit.
Signed-off-by: Reinder de Haan <patchesrdh@mveas.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Use of_match_node instead of calling of_device_is_compatible a ton of
times to get model specific config data.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Both data->id_det_gpio and data->vbus_det_gpio are optional, so use
devm_gpiod_get_optional for them.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
*) Add new NXP USB OTG PHY driver
*) Add vbus/id detection, extcon support and fixes in phy-sun4i-usb
driver
*) Add support to use phy-sun4i-usb driver for sun8i-a23 and sun8i-a33
SoCs
*) Other trivial code cleanups, dropping .owner assignment and constify
phy_ops
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJVyhKbAAoJEA5ceFyATYLZIRcP/ivt04ocgcZ7+kyTC55uUvoA
I/YAQScDW+LWdCeEE11nWl5oDDecaMDFs/aIVAbuEt38lya6lIzU66gsFlJpJCHj
LolnyE8DU8WhEkJRdMsDFVLX+oaNPHHfhIGEorm/FwdoJ6oT0TQ1NZbw7qh6o+T9
+Eb/T8nSTFIHWm24E0MN2pos9mvG4FtDeNp09j05y0F6L/AuLj/eBVJN5vNQ5YgZ
onA0YuPNzEJOOdgPJp2WiG2U72evCsCXy5X95gBbz/Fk7uj+vvgy+rMNorOZik+H
jLHGuV5kynHGehjn7+UaiPAU4zFfuqbVSyF07tMVqRdb5nGN9621DcfR9jieb2/g
3I0BQcHohwTjQvffdifCcDdF6YwzdLtZQwUEqjngafDoi5mfoolLupsTpLO9GOAO
Dq5ZbvqHKoCdQ1h+LZ6KRrr+de9Lrp3P/Ys/9t22e+DF3Vhq0QW8KNMJtNVutrFx
RZmiuf5AWPieZBwaVzWVI5AX8Y2KsoVX9BXiOsgkFuFhd3V6lkpI56UlV36IP+rD
E8MZ1NblCD+zR19DeZByyl2q1jvK3APNsQQrF3YzIGw9/yaJvVsMvpHIlF9gQ3Z1
A8rvUn3nYW6Gnc9L3b7VQJM15n8K0bym4fPkCIRe5yimC+a5ztxddEajYynmpQGg
5C9QmBF7MH6HlXwVPF4R
=97xz
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.3
*) Add new NXP USB OTG PHY driver
*) Add vbus/id detection, extcon support and fixes in phy-sun4i-usb
driver
*) Add support to use phy-sun4i-usb driver for sun8i-a23 and sun8i-a33
SoCs
*) Other trivial code cleanups, dropping .owner assignment and constify
phy_ops
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The phy_ops variables are never modified after initialized in these
drivers, so make them const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
data->vbus_det is always 1 on boards without a (working) vbus-det, skip
the vbus_det test on such boards.
This fixes the sun4i usb phy code never turning on Vbus on such boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Move vbus-detect helper functions up in the file, just moving some code
around, no functional changes what so ever.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
sun4i_usb_phy_set_squelch_detect is used by other code, which may be built
as a module, so it should be exported.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
On some boards there is no vbus_det gpio pin, instead vbus-detection for
otg can be done via the pmic.
This commit adds support for monitoring vbus_det via the power_supply
exported by the pmic, enabling support for otg on these boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
On some boards we cannot detect the presence of an external Vusb, because
e.g. the 5V of the otg connector is directly connected to the 5V of the board,
and thus is always high.
This commit adds support for using such boards by only looking at the
id-detection pin.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The usb-phys on the sun8i-a33 SoC are mostly the same as sun8i-a23 but for
some reason (hw bug?) the phyctl register was moved to a different address
and is not initialized to 0 on reset.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The usb-phys on the sun8i-a23 SoC have the same setup wrt clocks as on the
sun6i-a31 SoC, but there are only 2 instead of 3 like on the sun5i-a13 SoC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Before this commit the code for determining the disconnect threshold was
checking for "allwinner,sun4i-a10-usb-phy" or "allwinner,sun6i-a31-usb-phy"
assuming that those where the exception and then newer SoCs would use a
disconnect threshold of 2 like sun7i does. But it turns out that newer
SoCs use a disconnect threshold of 3 and sun5i and sun7i are the
exceptions, so check for those instead.
Here are the settings from the various Allwinner SDK sources:
sun4i-a10: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
sun5i-a13: USBC_Phy_Write(usbc_no, 0x2a, 2, 2);
sun6i-a31: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
sun7i-a20: USBC_Phy_Write(usbc_no, 0x2a, 2, 2);
sun8i-a23: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
sun8i-h3: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
sun9i-a80: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
Note this commit makes no functional changes as currently we only support
sun4i - sun7i.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The sunxi musb glue needs to know if a host or normal usb cable is plugged
in, add extcon support so that the musb glue can monitor the host status.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The usb0 phy is connected to an OTG controller, and as such needs some special
handling:
1) It allows explicit control over the pullups, enable these on phy_init and
disable them on phy_exit.
2) It has bits to signal id and vbus detect to the musb-core, add support for
for monitoring id and vbus detect gpio-s for use in dual role mode, and set
these bits to the correct values for operating in host only mode when no
gpios are specified in the devicetree.
While updating the devicetree binding documentation also add documentation
for the sofar undocumented usage of regulators for vbus for all 3 phys.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The sunxi otg phy has a bug where it wrongly detects a high speed squelch
when reset on the root port gets de-asserted with a lo-speed device.
The workaround for this is to disable squelch detect before de-asserting
reset, and re-enabling it after the reset de-assert is done. Add a sunxi
specific phy function to allow the sunxi-musb glue to do this.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The allwinner SDK uses a value of 3 for the disconnect threshold setting on
sun6i, do the same in the kernel.
In my previous experience with sun5i problems getting the threshold right
is important to avoid usb2 devices being unplugged sometimes going unnoticed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The users of the old method are now converted to the new one.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
[ kishon@ti.com : made phy-berlin-usb.c and phy-miphy28lp.c to use the updated
devm_phy_create API.]
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The driver for sun4i USB phys currently supports
only phy1 and phy2 which are used for USB host
controllers. This patch adds support for USB phy0,
which is used by the musb hdrc USB controller.
Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch removes the superflous .owner field for drivers which
use the module_platform_driver or platform_driver_register api,
as this is overriden in __platform_driver_register.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
In case of multi-phy PHY providers, each PHY should be modeled as a sub
node of the PHY provider. Then each PHY will have a different node pointer
(node pointer of sub node) than that of PHY provider. Added this provision
in the PHY core.
Also fixed all drivers to use the updated API.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
PTR_ERR_OR_ZERO simplifies the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The USB phy controller in the A31 differs mostly from the older controllers
because it has a clock dedicated for each phy, while the older ones were having
a single clock for all the phys.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Move the phy initialization and variables declaration to the loop itself, since
it is where it really belongs. Also remove all the temporary variables, we can
use the structure members directly.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The Allwinner A1x / A2x SoCs have 2 or 3 usb phys which are all accessed
through a single set of registers. Besides this there are also some other
phy related bits which need poking, which are per phy, but shared between the
ohci and ehci controllers, so these are also controlled from this new phy
driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Hans de Goede