Enable the port when disabling countermeasures, and disable it on
enabling countermeasures.
This bug causes the response of the system to certain attacks to be
ineffective.
It also prevents wpa_supplicant from getting scan results, as
wpa_supplicant disables countermeasures on startup - preventing the
hardware from scanning.
wpa_supplicant works with ap_mode=2 despite this bug because the commit
handler re-enables the port.
The log tends to look like:
State: DISCONNECTED -> SCANNING
Starting AP scan for wildcard SSID
Scan requested (ret=0) - scan timeout 5 seconds
EAPOL: disable timer tick
EAPOL: Supplicant port status: Unauthorized
Scan timeout - try to get results
Failed to get scan results
Failed to get scan results - try scanning again
Setting scan request: 1 sec 0 usec
Starting AP scan for wildcard SSID
Scan requested (ret=-1) - scan timeout 5 seconds
Failed to initiate AP scan.
Reported by: Giacomo Comes <comes@naic.edu>
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
... and interface up.
In these situations, you are usually trying to connect to a new AP, so
keeping TKIP countermeasures active is confusing. This is already how
the driver behaves (inadvertently). However, querying SIOCGIWAUTH may
tell userspace that countermeasures are active when they aren't.
Clear the setting so that the reporting matches what the driver has
done..
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HW has to be set to FULLSLEEP mode during suspend,
when no interface has been brought up. Not doing this would
break resume, as the chip won't be powered up at all.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This results in an erroneus num_adhoc_vifs count, as the this counter
was incremented but not decremented for mesh interfaces.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The interrupt handler takes a lock - but since commit bcad6e80f3 this
lock goes through an indirection specified in the hermes_t structure.
We must therefore initialise the structure before setting up the
interrupt handler.
Fix orinoco_cs and spectrum_cs
<https://bugzilla.kernel.org/show_bug.cgi?id=23932>
Bisected by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to set LRO on ehea, the user must set a module parameter, which
is not the standard way to do so. This patch adds a way to set LRO using
the ethtool tool.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Regarding benet be_cmd_multicast_set() function, now using
netdev_for_each_mc_addr() helper for mac address copy, but
when copying to req->mac[] did not increase of the index.
Cc: Sathya Perla <sathyap@serverengines.com>
Cc: Subbu Seetharaman <subbus@serverengines.com>
Cc: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Cc: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When matching error address to the range contained by one memory node,
we're in valid range when node interleaving
1. is disabled, or
2. enabled and when the address bits we interleave on match the
interleave selector on this node (see the "Node Interleaving" section in
the BKDG for an enlightening example).
Thus, when we early-exit, we need to reverse the compound logic
statement properly.
Cc: <stable@kernel.org>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
This corrects the misprint introduced when moving '#if
PAGE_SHIFT' from i7core_edac.c to edac_core.h (commit
e9144601d3)
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andrei Konovalov <akonovalov@mvista.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
00740c5854 changed edac_core to
un-/register a workqueue item only if a lowlevel driver supplies a
polling routine. Normally, when we remove a polling low-level driver, we
go and cancel all the queued work. However, the workqueue unreg happens
based on the ->op_state setting, and edac_mc_del_mc() sets this to
OP_OFFLINE _before_ we cancel the work item, leading to NULL ptr oops on
the workqueue list.
Fix it by putting the unreg stuff in proper order.
Cc: <stable@kernel.org> #36.x
Reported-and-tested-by: Tobias Karnat <tobias.karnat@googlemail.com>
LKML-Reference: <1291201307.3029.21.camel@Tobias-Karnat>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
If we break the loop when there are still skbs in tq and no skb in
rq, the skbs will be left in txq until new skbs are enqueued into rq.
In rare cases, no new skb is queued, then these skbs will stay in rq
forever.
After this patch, if tq isn't empty when we break the loop, we goto
resched directly.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the calculation of the inexact hash-based MAC address filter.
It's 64 bits but current code is missing a ULL. Results in filtering out
some legitimate packets.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow 1 as a valid div value as specified in the ADM1026 datasheet.
Signed-off-by: Gabriele Gorla <gorlik@penguintown.net>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Prevent setting fan_div from stomping on other fans that share the
same I2C register.
Signed-off-by: Gabriele Gorla <gorlik@penguintown.net>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The manual fan speed control logic of the IT8721F is much different
from what older devices had. Update the code to properly support that.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: i915 cannot provide switcher services.
drm/radeon/kms: fix vram base calculation on rs780/rs880
drm/radeon/kms: fix formatting of vram and gtt info
drm/radeon/kms: forbid big bo allocation (fdo 31708) v3
drm: Don't try and disable an encoder that was never enabled
drm: Add missing drm_vblank_put() along queue vblank error path
drm/i915/dp: Only apply the workaround if the select is still active
drm/i915: Emit a request to clear a flushed and idle ring for unbusy bo
drm/i915/lvds: Always restore panel-fitter when enabling the LVDS
drm/i915/ringbuffer: Only print an error on the second attempt to reset head
drm/i915: announce to userspace that the bsd ring is coherent
agp/intel: Fix wrong kunmap in i830_cleanup()
drm/i915: Factor in pixel-repeat in FDI M/N calculation
drm/i915: Death to the unnecessary 64bit divide
drm/i915: Clean conflicting modesetting registers upon init
drm/i915: Apply a workaround for transitioning from DP on pipe B to HDMI.
drm/i915: Always set the DP transcoder config to 8BPC.
Adds new Bamboo Pen & Touch model - Bamboo P & T Special Edition
Medium (CTH661/L; Product ID = 0xdb).
Tested-by: Tobias Verbeke <tobias.verbeke@gmail.com>
Signed-off-by: David Foley <favux.is@gmail.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The firmware framework gets initialized during fs_initcall time, so
we are not allowed to call request_firmware earlier.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Avoid overflowing a 32 bit value.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Forbid allocating buffer bigger than visible VRAM or GTT, also
properly set lpfn field.
v2 - use max macro
- silence warning
v3 - don't explicitly set range limit
- use min macro
Cc: stable <stable@kernel.org>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Prevents code that assumes that the encoder is active when asked to be
disabled from dying a horrible death.
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Kristian Høgsberg <krh@bitplanet.net>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Currently, in case of using scatter/gather mode, head of data is not sent to
destination. The cause is second descriptor address is set to NEXT.
The NEXT must have head of descriptor address.
This patch sets head of descriptor address to the NEXT.
Acked-by: Yong Wang <youg.y.wang@intel.com>
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
[dan.j.williams@intel.com: fixed up usage of virt_to_phys()]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
As we may try to power down the link at various times, it is not
necessarily still coupled with an encoder and so we must be careful not
to depend upon an operation that is only valid when the link is still
attached to a pipe.
Fixes regression in 5bddd17.
Reported-and-tested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org [after applying 5bddd17]
Call netif_napi_{add,del}() on the NAPI contexts in the new and
old channels, respectively.
Since efx_init_napi() cannot fail, make its return type void.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The beacon tasklet is accesssing the bslot info for beacon generation.
Meanwhile the same slot can be freed on interface deletion.
Current the remove_interface disables the beacon alert after freeing the slot.
This may leads to null pointer access.
This patch disables SWBA and kills the beacon tasklet to prevent access
to the slot to be freed. After releasing the slot, swba will be enabled again
upon the availablity of beaconing interfaces.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR_RxKeyIdxValid will not be set for bcast/mcast frames and so relying
this status for MIC failed frames is buggy.
Due to this, MIC failure events for broadcast frames are not sent to
supplicant resulted in AP disconnecting the STA.
Able to pass Wifi Test case 5.2.18 with this fix.
Cc: Stable <stable@kernel.org> (2.6.36+)
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When ath_drain_all_txq fails to stop DMA, it issues a hw reset. This reset
happens at a very problematic point in time, when the hardware rx path has
not been stopped yet. This could lead to memory corruption, hardware hangs
or other issues.
To fix these issues, simply remove the reset entirely and check the tx DMA
stop status to prevent problems with fast channel changes.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath9k driver subtracts 3 dBm to the txpower as with two radios the
signal power is doubled.
The resulting value is assigned in an u16 which overflows and makes
the card work at full power.
Cc: stable@kernel.org
Signed-off-by: Matteo Croce <matteo@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we are using a legacy interrupt, our IRQ may be shared and our
interrupt handler may be called even though interrupts are disabled on
the NIC. When we change ring sizes, we reallocate the event queue and
the interrupt handler may use an invalid pointer when called for
another device's interrupt.
Maintain a legacy_irq_enabled flag and test that at the top of the
interrupt handler. Note that this problem results from the need to
work around broken INT_ISR0 reads, and does not affect the legacy
interrupt handler for Falcon A1.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86:
wmi: use memcmp instead of strncmp to compare GUIDs
ACPI, hp-wmi: Fix memory leak in acpi query
msi-wmi: fix semantically incorrect use of keycode instead of scancode
msi-wmi: Add mute key support
asus-laptop: add wimax and wwan support
eeepc-wmi: fix compiler warning
ibm_rtl: _RTL_ is not available in UEFI mode
ibm_rtl: Loosen the DMI criteria to all IBM machines
drivers/platform/x86/thinkpad_acpi.c: delete double assignment
eeepc-wmi: add cpufv sysfs documentation
toshiba_acpi.c: Add key_entry for a lone FN keypress
ibm_rtl: fix printk format warning
In order for bos to retire eventually, a request must be sent down the
ring. This is expected, for example, by occlusion queries for which mesa
will wait upon (whilst running glean) before issuing more batches and so
the normal activity upon the ring is suspended and we need to emit a
request to clear the idle ring.
Reported-by: Jinjin, Wang <jinjin.wang@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30380
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The existing gpio-keys driver can be usable only for GPIO lines with
interrupt support. Several devices have buttons connected to a GPIO
line which is not capable to generate interrupts. This patch adds a
new input driver using the generic GPIO layer and the input-polldev
to support such buttons.
[Ben Gardiner <bengardiner@nanometrics.ca: fold code to use more
of the original gpio_keys infrastructure; cleanups and other
improvements.]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 2c01946c6b (omap3 nand: cleanup
virtual address usages) wrongly enabled CONFIG_MTD_NAND_OMAP_HWECC
which breaks boards like beagle and pandora that use software ECC
for write.
Boards like beagle and pandora uses sw ecc for write (e.g. binary flushed
from u-boot) and read from kernel.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6524/1: GIC irq desciptor bug fix
ARM: 6523/1: iop: ensure sched_clock() is notrace
ARM: 6456/1: Fix for building DEBUG with sa11xx_base.c as a module.
ARM: 6519/1: kuser: Fix incorrect cmpxchg syscall in kuser helpers
ARM: 6505/1: kprobes: Don't HAVE_KPROBES when CONFIG_THUMB2_KERNEL is selected
ARM: 6508/1: vexpress: Correct data alignment in headsmp.S for CONFIG_THUMB2_KERNEL
ARM: 6507/1: RealView: Correct data alignment in headsmp.S for CONFIG_THUMB2_KERNEL
ARM: 6504/1: Thumb-2: Fix long-distance conditional branches in head.S for Thumb-2.
ARM: 6503/1: Thumb-2: Restore sensible zImage header layout for CONFIG_THUMB2_KERNEL
ARM: 6502/1: Thumb-2: Fix CONFIG_THUMB2_KERNEL breakage in compressed/head.S
ARM: 6501/1: Thumb-2: Correct data alignment for CONFIG_THUMB2_KERNEL in mm/proc-v7.S
ARM: 6500/1: Thumb-2: Correct data alignment for CONFIG_THUMB2_KERNEL in kernel/head.S
ARM: 6499/1: Thumb-2: Correct data alignment for CONFIG_THUMB2_KERNEL in bootp/init.S
ARM: 6498/1: vfp: Correct data alignment for CONFIG_THUMB2_KERNEL
ARM: 6497/1: kexec: Correct data alignment for CONFIG_THUMB2_KERNEL
ARM: 6496/1: GIC: Do not try to register more then NR_IRQS interrupts
ARM: cns3xxx: Fix build with CONFIG_PCI=y
While looking for the duplicates in /sys/class/wmi/, I couldn't find
them. The code that looks for duplicates uses strncmp in a binary GUID,
which may contain zero bytes. The right function is memcmp, which is
also used in another section of wmi code.
It was finding 49142400-C6A3-40FA-BADB-8A2652834100 as a duplicate of
39142400-C6A3-40FA-BADB-8A2652834100. Since the first byte is the fourth
printed, they were found as equal by strncmp.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: stable@kernel.org
After freeing the rings we were not zeroing out the ring count values.
This patch now clears these counts correctly.
Reported-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
initramfs: Really fix build break on symbol-prefixed archs
[media] Fix Kconfig errors due to two visible menus
i2c/algos: convert Kconfig to use the menu's `visible' keyword
media/video: convert Kconfig to use the menu's `visible' keyword
Revert "i2c: Fix Kconfig dependencies"
kconfig: regen parser
kconfig: add an option to determine a menu's visibility
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
parisc: Fix GSC PS/2 driver name for keyboard and mouse
parisc: KittyHawk LCD fix
parisc: convert the rest of the irq handlers to simple/percpu
parisc: fix dino/gsc interrupts
parisc: remove redundant initialization in sigsegv path of sys_rt_sigreturn
Linus Torvalds pointed out that our code was unbalanced when powering on
the panel with respect to the power off sequence in that we were failing
to restore the panel-fitter. The consequence of this would be that
across a simple DPMS off/on for a non-native mode, without an intervening
modeset, the panel fitter would remain disabled and the output would shift
on the panel.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
There's not much we can do here but hope for the best. However the first
failure happens quite frequently and if often remedied by the second
attempt to reset HEAD. So only print the error if that attempt also
fails.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=19802
Reported-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Otherwise we can't really fix the abi-braindeadness of forcing
libva to manually wait for rendering when switching rings. Which
in turn makes implementing hw semaphores a pointless exercise
(at least for ironlake).
[Also added the relaxed fencing param to explain the jump in
numbering - relaxed fencing is in -next.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Add a missing NULL check and fix the wrong address passed to kunmap()
in i830_cleanup().
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[danvet: added cc stable]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Rename intel_mid_dma_pci to intel_mid_dma_pci_driver to pick up the
applied annotations of that suffix.
Reported-by: <major_Lee@wistron.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Currently while submitting scatterlists with more than one SG
entry the DMA buffer address from the first SG entry is inserted
into all initialized DMA buffer descriptors. This is due to the
typo in the for_each_sg() loop where the scatterlist pointer is
used for obtaining the DMA buffer address and _not_ the SG list
iterator.
As a result all received data will be written only into the first
DMA buffer while reading. While writing the data from the first
DMA buffer is send to the device multiple times. This caused
the filesystem destruction on the MMC card when using DMA in
mxcmmc driver.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Changed Makefile to use <modules>-y instead of <modules>-objs. Following
(documentation/kbuild/makefiles.txt).
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
K class aka KittyHawk don't have LED support on their LCD. Installing
HP-UX confirmed this. The current led_wq fills the LCD with black
characters each time it runs.
The patch prevents the led_wq workqueue and its proc entry to be
created for KittyHawk machines.
It also increase min_cmd_delay as currently, one character out of two
is lost when a string is sent to the LCD.
Signed-off-by: Guy Martin <gmsoft@tuxicoman.be>
Signed-off-by: Kyle McMartin <kyle@mcmartin.c>
The generic conversion eliminates the spurious no_ack and no_end
routines, converts all the cascaded handlers to handle_simple_irq() and
makes iosapic use a modified handle_percpu_irq() to become the same as
the CPU irq's. This isn't an essential change, but it eliminates the
mask/unmask overhead of handle_level_irq().
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Fixes the modesetting on the secondary panel of the Libretto W100 and
presumably many more Ironlake laptops with SDVO LVDS displays.
Reported-and-tested-by: Matthew Willoughby <mattfredwill@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
This patch fixes a compilation issue when compiling PCMCIA SA1100
support as a module with PCMCIA_DEBUG enabled. The symbol
soc_pcmcia_debug was not beeing exported.
ARM: pcmcia: Fix for building DEBUG with sa11xx_base.c as a module.
This patch fixes a compilation issue when compiling PCMCIA SA1100
support as a module with PCMCIA_DEBUG enabled. The symbol
soc_pcmcia_debug was not beeing exported.
Cc: <stable@kernel.org>
Signed-off-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the hardware DDA to calculate the ratio with as much accuracy as is
possible.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
* '2.6.37-rc4-pvhvm-fixes' of git://xenbits.xen.org/people/sstabellini/linux-pvhvm:
xen: unplug the emulated devices at resume time
xen: fix save/restore for PV on HVM guests with pirq remapping
xen: resume the pv console for hvm guests too
xen: fix MSI setup and teardown for PV on HVM guests
xen: use PHYSDEVOP_get_free_pirq to implement find_unbound_pirq
* 'upstream/core' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
xen: allocate irq descs on any NUMA node
xen: prevent crashes with non-HIGHMEM 32-bit kernels with largeish memory
xen: use default_idle
xen: clean up "extra" memory handling some more
* 'upstream/bugfix' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
xen: x86/32: perform initial startup on initial_page_table
xen: don't bother to stop other cpus on shutdown/reboot
If we leave the registers in a conflicting state then when we attempt
to teardown the active mode, we will not disable the pipes and planes
in the correct order -- leaving a plane reading from a disabled pipe and
possibly leading to undefined behaviour.
Reported-and-tested-by: Andy Whitcroft <apw@canonical.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=32078
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: se/7724: Remove FSI/B of GPIO init code
sh: se/7724: Update clock framework of FSI clock to non-legacy
sh: Assume new page cache pages have dirty dcache lines.
sh: boards: mach-se: use IS_ERR() instead of NULL check
sh: Add div6_reparent_clks to clock framework for FSI
dma: shdma: add a MODULE_ALIAS() to allow module autoloading
* 'fbdev-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6:
lxfb: Maintain video processor palette through suspend/resume
video: da8xx: Register IRQ as last thing in driver probing.
framebuffer: fix fbcmap.c kernel-doc warning
My new shiny code for corrupted PEB detection has NOR specific bug.
We tread PEB as corrupted and preserve it, if
1. EC header is OK.
2. VID header is corrupted.
3. data area is not "all 0xFFs"
In case of NOR we have 'nor_erase_prepare()' quirk, which invalidates
the headers before erasing the PEB. And we invalidate first the VID
header, and then the EC header. So if a power cut happens after we have
invalidated the VID header, but before we have invalidated the EC
header, we end up with a PEB which satisfies the above 3 conditions,
and the scanning code will treat it as corrupted, and will print
scary warnings, wrongly.
This patch fixes the issue by firt invalidating the EC header, then
invalidating the VID header. In case of power cut inbetween, we still
just lose the EC header, and UBI can deal with this situation gracefully.
Thanks to Anatolij Gustschin <agust@denx.de> for tracking this down.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Reported-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Anatolij Gustschin <agust@denx.de>
Use the ccflag-y flag instead of EXTRA_CFLAGS because EXTRA_CFLAGS is
deprecated and should now be switched. According to (documentation/kbuild/makefiles.txt).
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We should not call kfree(dma) in mid_setup_dma error path because
the memory is allocated in intel_mid_dma_probe and will be freed
in intel_mid_dma_probe error path if mid_setup_dma return error.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
otherwise, i will be -1 inside the latest iteration of the while loop.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: length resolution should be reported units/mm
HID: add support for F430 Force Feedback Wheel
HID: egalax: Use kzalloc
HID: Remove KERN_DEBUG from dbg_hid use
Manually fixed trivial conflict in drivers/hid/hid-input.c (due to
removal of KERN_DEBUG from dbg_hid use clashing with new keycode
interface switch)
Allocate irq descs on any NUMA node (we don't care) rather than
specifically node 0, which may not exist.
(At the moment NUMA is meaningless within a domain, so any info
the kernel has is just from an SRAT table we haven't suppressed/disabled.)
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
If this is a non-HIGHMEM 32-bit kernel, then the page structures only go
up to the limit of addressable memory, even if more memory is physically
present. Don't try to add that extra memory to the balloon.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
The AMD Geode CS5536 Companion Device Silicon Revision B1 Specification
Update mentions the follow as issue #36:
"Atomic write transactions to the atomic GPIO High Bank Feature Bit
registers should only affect the bits selected [...]"
"after Suspend, an atomic write transaction [...] will clear all
non-selected bits of the accessed register."
In other words, writing to the high bank for a single GPIO bit will
clear every other GPIO bit (but only sometimes after a suspend).
The workaround described is obvious and simple; do a read-modify-write.
This patch does that, and documents why we're doing it.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's not useful to build LED triggers when there's no LEDs that can be
triggered by them. Therefore, fix up the dependencies so that this
cannot happen, and fix a few users that select triggers to depend on
LEDS_CLASS as well (there is also one user that also selects LEDS_CLASS,
which is OK).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Tested-by: Ingo Molnar <mingo@elte.hu>
Cc: Arnd Hannemann <arnd@arndnet.de>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This workaround only applies to Ironlake.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
The pipe is always set to 8BPC, but here we were leaving whatever
previous bits were set by the BIOS in place.
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
This patch fixes hang in dmfe driver on attempt of sending a big packet.
Without this patch the code stops the queue and never wakes it again.
Signed-off-by: Alexander V. Lukyanov <lav@netis.ru>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To reproduce: if connman (http://connman.net/) is started,
inserting the stmmac module triggers a "BUG: spinlock bad magic on CPU#0".
Registering the device in stmmac_probe() sends a notification to connman
which brings the interface up before the lock is initialized.
Signed-off-by: Vlad Lungu <vlad.lungu@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (27 commits)
Staging: rt2870: Add USB ID for Buffalo Airstation WLI-UC-GN
staging: easycap needs smp_lock.h, fixes build error
Staging: batman-adv: ensure that eth_type_trans gets linear memory
Staging: batman-adv: Don't remove interface with spinlock held
staging: brcm80211: updated maintainers contact information
staging: fix winbond build, needs delay.h
Staging: line6: fix up my fixup for some sysfs attribute permissions
Staging: zram: fix up my fixup for some sysfs attribute permissions
Staging: udlfb: fix up my fixup for some sysfs attribute permissions
Staging: samsung-laptop: fix up my fixup for some sysfs attribute permissions
Staging: iio: adis16220: fix up my fixup for some sysfs attribute permissions
Staging: frontier: fix up my fixup for some sysfs attribute permissions
Staging: asus_oled: fix up my fixup for some sysfs attribute permissions
staging: spectra: fix build error
Staging: intel_sst: fix memory leak
Staging: rtl8712: signedness bug in init
staging: rtl8187se: Change panic to warn when RF switch turned off
staging: comedi: fix memory leak
Staging: quickstart: free after input_unregister_device()
Staging: speakup: free after input_unregister_device()
...
* 'driver-core-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
uio: Change mail address of Hans J. Koch
driver core: prune docs about device_interface
driver core: the development tree has switched to git
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
serial: mfd: adjust the baud rate setting
TTY: open/hangup race fixup
TTY: don't allow reopen when ldisc is changing
NET: wan/x25, fix ldisc->open retval
TTY: ldisc, fix open flag handling
serial8250: Mark console as CON_ANYTIME
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: fix autosuspend bug in usb-serial
USB: ehci: disable LPM and PPCD for nVidia MCP89 chips
USB: serial: ftdi_sio: Vardaan USB RS422/485 converter PID added
USB: yurex: add .llseek fop to file_operations
USB: ftdi_sio: Add ID for RT Systems USB-29B radio cable
usb: musb: do not use dma for control transfers
usb: musb: gadget: fix compilation warning
usb: musb: clear RXCSR_AUTOCLEAR before PIO read
usb: musb: unmap dma buffer when switching to PIO
xhci: Don't let the USB core disable SuperSpeed ports.
xhci: Setup array of USB 2.0 and USB 3.0 ports.
xhci: Fix reset-device and configure-endpoint commands
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB: Fix information leak in marshalling code
IB/pack: Remove some unused code added by the IBoE patches
IB/mlx4: Fix IBoE link state
IB/mlx4: Fix IBoE reported link rate
mlx4_core: Workaround firmware bug in query dev cap
IB/mlx4: Fix memory ordering of VLAN insertion control bits
MAINTAINERS: Update NetEffect entry
This reverts commit 916448e77f.
"As far as I can tell, either of these patches breaks multiple VIF
scenarios. I'm not sure exactly why, but I had to revert this to
get any of my interfaces to associate."
-- Ben Greear <greearb@candelatech.com>
http://marc.info/?l=linux-wireless&m=129123368719339&w=2
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few LNA control related flags were also specified as a bitfields, however
for some strange reason they were written in big-endian order this time.
Fix this by using flags instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Parsing data using bitfields is messy, because it makes endian handling
much harder. AR9002 and earlier got it right, AR9003 got it wrong.
This might lead to either using too high or too low tx power values,
depending on frequency and eeprom settings.
Fix it by getting rid of the CTL related bitfields entirely and use
masks instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The register which gives input gpio state is 0x404c for ar9003,
currently 0x4048 is wrongly used. This will disable RF and make
it unusable on some of AR9003.
Cc:stable@kernel.org
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
regulator: fix kernel-doc for set_consumer_device_supply
regulator: enable supply regulator only when use count is zero
regulator: twl-regulator - fix twlreg_set_mode
regulator: lock supply in regulator enable
regulator: Return proper error for regulator_register()
regulator: Ensure enough delay time for enabling regulator
regulator: Remove a redundant device_remove_file call in create_regulator
regulator: Staticise mc13783_powermisc_rmw()
regulator: regulator disable supply fix
When remapping MSIs into pirqs for PV on HVM guests, qemu is responsible
for doing the actual mapping and unmapping.
We only give qemu the desired pirq number when we ask to do the mapping
the first time, after that we should be reading back the pirq number
from qemu every time we want to re-enable the MSI.
This fixes a bug in xen_hvm_setup_msi_irqs that manifests itself when
trying to enable the same MSI for the second time: the old MSI to pirq
mapping is still valid at this point but xen_hvm_setup_msi_irqs would
try to assign a new pirq anyway.
A simple way to reproduce this bug is to assign an MSI capable network
card to a PV on HVM guest, if the user brings down the corresponding
ethernet interface and up again, Linux would fail to enable MSIs on the
device.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Use the new hypercall PHYSDEVOP_get_free_pirq to ask Xen to allocate a
pirq. Remove the unsupported PHYSDEVOP_get_nr_pirqs hypercall to get the
amount of pirq available.
This fixes find_unbound_pirq that otherwise would return a number
starting from nr_irqs that might very well be out of range in Xen.
The symptom of this bug is that when you passthrough an MSI capable pci
device to a PV on HVM guest, Linux would fail to enable MSIs on the
device.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
On some motherboards the it8712f watchdog does not work unless
the game port was enabled. see Bug 13140. We therefor add a note
to Kconfig.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
* fix devinit and devexit sections
* fix platform removal code so that the iounmap happens after the removal of the timer.
* changes the reboot_notifier by a platform shutdown method.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds an additional LPC Controller DeviceID for the Intel Patsburg PCH for TCO Watchdog.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Input ABI requires reporting resolution on main axes in units per
millimeter, not units per inch, so we need to convert accordingly.
Tested-by: Nikolai Kondrashov <spbnick@gmail.com>
Acked-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We erroneously ignored the Always Running APIC Timer on WSM-EX.
Move the check for ARAT down so that it can apply to any/all models.
Signed-off-by: Len Brown <len.brown@intel.com>
ib_ucm_init_qp_attr() and ucma_init_qp_attr() pass struct ib_uverbs_qp_attr
with reserved, qp_state, {ah_attr,alt_ah_attr}{reserved,->grh.reserved}
fields uninitialized to copy_to_user(). This leads to leaking of
contents of kernel stack memory to userspace.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use netif_running() and netif_carrier_ok() to report link state,
exactly as is done to report Ethernet link state in sysfs.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The link rate is the product of the link speed in the link width. For
Etherent ports the rate is 10G, so we use 1 for the width and 4 for
speed to get the correct rate.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ConnectX firmware is supposed to report the number blue flame
registers per page as log2 of the value. However, due to a firmware
bug, it reports actual number. This patch works around this by
checking if the number of registers calculated fits within a page. If
it does not, we use 8 registers per page.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The new interface creates directories per mapped image
and under each it creates a subdir per available snapshot.
This allows keeping a cleaner interface within the sysfs
guidelines. The ABI documentation was updated too.
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Yehuda Sadeh <yehuda@hq.newdream.net>
Signed-off-by: Sage Weil <sage@newdream.net>
If turning on a power resource fails, do not reference count it,
since it cannot be in use in that case.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Commit 3e384ee6c6 (ACPI / PM: Fix
reference counting of power resources) introduced a regression by
causing fan power resources to be turned on and reference counted
unnecessarily during resume, so on some boxes fans are always on
after resume.
Fix the problem by checking if the current device state is different
from the new state before reference counting and turning on power
resources in acpi_power_transition().
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=22932 .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: Maciej Rutecki <maciej.rutecki@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Restore the check for an unassigned mac address before adopting the
first slaves as it's own. The change in behavior was introduced by:
commit c20811a79e
Author: Jiri Pirko <jpirko@redhat.com>
bonding: move dev_addr cpy to bond_enslave
Signed-off-by: David Strand <dpstrand@gmail.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code for the b44_wap54g10_workaround was never included, because
the config option was wrong. The nvram_get function was never in
mainline kernel, only in external OpenWrt patches.
The code should be compiled in when CONFIG_BCM47XX is selected and not
when CONFIG_SSB_DRIVER_MIPS is selected, because nvram_getenv is only
available on bcm47xx platforms and now in the mainline kernel code.
Using an include is better than a second function declaration, to fix
this when the function signature changes.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must fully update the control segment before marking it as valid,
so that hardware doesn't start executing it before we're ready.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
[ Move VLAN control bit setting to before wmb(). - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Atheros 3011 has small sflash firmware and needs to be
blacklisted in transport driver to load actual firmware
in DFU driver.
Signed-off-by: Bala Shanmugam <sbalashanmugam@atheros.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
If a device is autosuspended an inability to resubmit URBs is
to be expected. Check the error code and only log real errors.
(Now that autosuspend is default enabled for btusb, those log
messages were happening all the time e.g. with a BT mouse)
Signed-off-by: Stefan Seyfried <seife+kernel@b1-systems.com>
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The ref-count of parport gained from parport_find_number()
was not released in normal path.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The Geode X driver uses both of the LX's palettes, one for gamma
correction and one for colormaps.
The kernel driver currently only backs up the one used for colormaps
during suspend/resume. If you mess with gamma settings and do a
suspend/resume, colors go funny.
Fix this by backing up the video proc palette during suspend/resume,
alongside the display controller one which is already handled.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Following commit exposed a bug in driver:
"fbdev: da8xx/omap-l1xx: implement double buffering"
Bug is, if interrupt handler is called before initialization is
finished, raster controller is enabled and following register
modifications causes hardware to stay in a broken state.
By looking at this one may say that proper locking is missing in
this driver, and a more proper fix should be prepared. However,
aformentioned commit causes a regression in the driver and some
fix to current one should be applied first.
Signed-off-by: Caglar Akyuz <caglar@bilkon-kontrol.com.tr>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use correct bit positions of rsid field.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Lenovo S10-3t's ClickPad is a 2-button ClickPad that reports BTN_LEFT
and BTN_RIGHT as normal touchpad, unlike the 1-button ClickPad used in
HP mini 210 that reports solely BTN_MIDDLE.
In 0xc0-cap response, the 1-button ClickPad has the 20-bit set while
2-button ClickPad has the 8-bit set.
This patch makes the kernel only handle 1-button ClickPad specially,
and treat 2-button ClickPad in the same fashion as regular touchpads.
This fixes kernel bug #18122 and MeeGo bug #4807.
Signed-off-by: Yan Li <yan.i.li@intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add two new Bamboo Pen & Touch models:
Bamboo Comic Medium (CTH661/S1; Product ID = 0xd8)
Bamboo P & T Special Edition Small (CTH461/L; Product ID = 0xdA)
Tested-by: IRIE Shinsuke <irieshinsuke@yahoo.co.jp>
Tested-by: Andrea Cadeddu <mrernia@gmail.com>
Signed-off-by: David Foley <favux.is@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: add workaround for dce3 ddc line vbios bug
drm/radeon/kms: fix interlaced and doublescan handling
drm/radeon/kms: fix typos in disabled vbios code
Revert "drm/i915/dp: use VBT provided eDP params if available"
drm/i915: Clear pfit registers when not used by any outputs
drm: record monitor status in output_poll_execute
drm: Set connector DPMS status to ON in drm_crtc_helper_set_config
drm/i915: fix regression due to ba3d8d749b
Revert "drm/radeon/kms: fix typo in r600 cs checker"
drm/i915/sdvo: Always add a 30ms delay to make SDVO TV detection reliable
MAINTAINERS: INTEL DRM DRIVERS list (intel-gfx) is subscribers-only
drm/i915/sdvo: Always fallback to querying the shared DDC line
drm/i915: Handle pagefaults in execbuffer user relocations
drm/i915/sdvo: Only enable HDMI encodings only if the commandset is supported
drm/radeon/kms: fix resume regression for some r5xx laptops
drm/radeon/kms: fix regression in rs4xx i2c setup
drm/i915: Only save/restore cursor regs if !KMS
drm/i915: Prevent integer overflow when validating the execbuffer
6xx/7xx was hitting the wrong BUS_CNTL reg and bits.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'intel/drm-intel-fixes' of /ssd/git/drm-next:
Revert "drm/i915/dp: use VBT provided eDP params if available"
drm/i915: Clear pfit registers when not used by any outputs
drm/i915: fix regression due to ba3d8d749b
Previous baud rate setting code only has been tested with 3.5M/9600/
115200/230400/460800 bps, and recently we got a 3M bps device to test,
which needs to modify current MUL register setting, and with this
patch 2.5M/2M/1.5M/1M/0.5M should also work as they just use a MUL
value scale down from 3M's.
Also got some reference register setting from silicon guys for
different baud rates, which tries to keep the pre-scalar register value
to 16.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
AR_RxKeyIdxValid will not be set for bcast/mcast frames and so relying
this status for MIC failed frames is buggy.
Due to this, MIC failure events for broadcast frames are not sent to
supplicant resulted in AP disconnecting the STA.
Able to pass Wifi Test case 5.2.18 with this fix.
Cc: Stable <stable@kernel.org> (2.6.36+)
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch (as1437) fixes a bug in the usb-serial autosuspend
handling. Since the usb-serial core now has autosuspend support, it
must set the .supports_autosuspend member in every serial driver it
registers. Otherwise the usb_autopm_get_interface() call won't work.
This fixes Bugzilla #23012.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: stable@kernel.org
Reported-by: Kevin Smith <thirdwiggin@gmail.com>
Reported-and-tested-by: Simon Gerber <gesimu@gmail.com>
Reported-and-tested-by: Matteo Croce <matteo@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Tested on MacBookAir3,1. Without this, we get EPROTO errors when
fetching device config descriptors.
Signed-off-by: Brian Tarricone <brian@tarricone.org>
Reported-by: Benoit Gschwind <gschwind@gnu-log.net>
Tested-by: Edgar Hucek <gimli@dark-green.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the PID for the Vardaan Enterprises VEUSB422R3 USB to RS422/485
converter. It uses the same chip as the FTDI_8U232AM_PID 0x6001.
This should also work with the stable branches for:
2.6.31, 2.6.32, 2.6.33, 2.6.34, 2.6.35, 2.6.36
Signed-off-by: Jacques Viviers <jacques.viviers@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Default llseek operation behavior was changed by the patch named
"vfs: make no_llseek the default" after the yurex driver had been merged,
so the llseek to yurex is now ignored.
This patch add llseek fop with default_llseek to yurex driver
to catch up to the change.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Another variant of the RT Systems programming cable for ham radios.
Signed-off-by: Michael Stuermer <ms@mallorn.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
passing argument 2 of 'dma_map_single' discards qualifiers from pointer target type
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fix kernel-doc warning for set_consumer_device_supply():
Warning(drivers/regulator/core.c:912): missing initial short description on line:
* set_consumer_device_supply: Bind a regulator to a symbolic supply
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Supply regulators are disabled only when the last
reference count is removed on the child regulator
(the use count goes from 1 to 0). This patch changes
the behaviour of enable so the supply regulator is
enabled only when the use count of the child
regulator goes from 0 to 1.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The Singular Message is 16 bits:
DEV_GRP[15:13] MT[12] RES_ID[11:4] RES_STATE[3:0]
Current implementation return immedially after sucessfuly write MSB part.
To properly set mode, we need to write the complete message ( MSB and LSB ).
In twl.h, now we have defines for PM Master module register offsets,
use it instead of hard coded 0x15/0x16.
Use "message & 0xff" to ensure we send correct value for LSB.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Lesly Arackal Manuel <leslyam@ti.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch add locks around regulator supply enable.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Integer division will truncate the result, this patch ensures we have
enough delay time for enabling regulator.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
We already have device_remove_file() in error path,
no need to call it before goto link_name_err.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
It is not used outside this driver so no need to make the symbol global.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch fixes a disable failure when regulator supply is used.
A while loop in regulator disable checks for supply pointer != NULL
but the pointer is not always updated, resulting in the while loop
running too many times causing a disable failure.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This reverts commit 869184a675.
This is required for the Sony Vaio Jesse was working on at the time, but
breaks most other eDP machines - machines that were working in earlier
kernels.
Reported-and-tested-by: Dave Airlie <airlied@redhat.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31188
Tested-by: Zhao Jian <jian.j.zhao@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Like in the "TTY: don't allow reopen when ldisc is changing" patch,
this one fixes a TTY WARNING as described in the option 1) there:
1) __tty_hangup from tty_ldisc_hangup to tty_ldisc_enable. During this
section tty_lock is held. However tty_lock is temporarily dropped in
the middle of the function by tty_ldisc_hangup.
The fix is to introduce a new flag which we set during the unlocked
window and check it in tty_reopen too. The flag is TTY_HUPPING and is
cleared after TTY_HUPPED is set.
While at it, remove duplicate TTY_HUPPED set_bit. The one after
calling ops->hangup seems to be more correct. But anyway, we hold
tty_lock, so there should be no difference.
Also document the function it does that kind of crap.
Nicely reproducible with two forked children:
static void do_work(const char *tty)
{
if (signal(SIGHUP, SIG_IGN) == SIG_ERR) exit(1);
setsid();
while (1) {
int fd = open(tty, O_RDWR|O_NOCTTY);
if (fd < 0) continue;
if (ioctl(fd, TIOCSCTTY)) continue;
if (vhangup()) continue;
close(fd);
}
exit(0);
}
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: <Valdis.Kletnieks@vt.edu>
Reported-by: Kyle McMartin <kyle@mcmartin.ca>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are many WARNINGs like the following reported nowadays:
WARNING: at drivers/tty/tty_io.c:1331 tty_open+0x2a2/0x49a()
Hardware name: Latitude E6500
Modules linked in:
Pid: 1207, comm: plymouthd Not tainted 2.6.37-rc3-mmotm1123 #3
Call Trace:
[<ffffffff8103b189>] warn_slowpath_common+0x80/0x98
[<ffffffff8103b1b6>] warn_slowpath_null+0x15/0x17
[<ffffffff8128a3ab>] tty_open+0x2a2/0x49a
[<ffffffff810fd53f>] chrdev_open+0x11d/0x146
...
This means tty_reopen is called without TTY_LDISC set. For further
considerations, note tty_lock is held in tty_open. TTY_LDISC is cleared in:
1) __tty_hangup from tty_ldisc_hangup to tty_ldisc_enable. During this
section tty_lock is held. However tty_lock is temporarily dropped in
the middle of the function by tty_ldisc_hangup.
2) tty_release via tty_ldisc_release till the end of tty existence. If
tty->count <= 1, tty_lock is taken, TTY_CLOSING bit set and then
tty_ldisc_release called. tty_reopen checks TTY_CLOSING before checking
TTY_LDISC.
3) tty_set_ldisc from tty_ldisc_halt to tty_ldisc_enable. We:
* take tty_lock, set TTY_LDISC_CHANGING, put tty_lock
* call tty_ldisc_halt (clear TTY_LDISC), tty_lock is _not_ held
* do some other work
* take tty_lock, call tty_ldisc_enable (set TTY_LDISC), put
tty_lock
I cannot see how 2) can be a problem, as there I see no race. OTOH, 1)
and 3) can happen without problems. This patch the case 3) by checking
TTY_LDISC_CHANGING along with TTY_CLOSING in tty_reopen. 1) will be
fixed in the following patch.
Nicely reproducible with two processes:
while (1) {
fd = open("/dev/ttyS1", O_RDWR);
if (fd < 0) {
warn("open");
continue;
}
close(fd);
}
--------
while (1) {
fd = open("/dev/ttyS1", O_RDWR);
ld1 = 0; ld2 = 2;
while (1) {
ioctl(fd, TIOCSETD, &ld1);
ioctl(fd, TIOCSETD, &ld2);
}
close(fd);
}
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: <Valdis.Kletnieks@vt.edu>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We should never return positive values from ldisc->open, tty layer
doesn't (and never did) expect that.
If we do that, weird things like warnings in tty_ldisc_close happen.
Not sure if dev->base_addr is used somehow now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Andrew Hendry <andrew.hendry@gmail.com>
Cc: linux-x25@vger.kernel.org
Tested-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a concrete ldisc open fails in tty_ldisc_open, we forget to clear
TTY_LDISC_OPEN. This causes a false warning on the next ldisc open:
WARNING: at drivers/char/tty_ldisc.c:445 tty_ldisc_open+0x26/0x38()
Hardware name: System Product Name
Modules linked in: ...
Pid: 5251, comm: a.out Tainted: G W 2.6.32-5-686 #1
Call Trace:
[<c1030321>] ? warn_slowpath_common+0x5e/0x8a
[<c1030357>] ? warn_slowpath_null+0xa/0xc
[<c119311c>] ? tty_ldisc_open+0x26/0x38
[<c11936c5>] ? tty_set_ldisc+0x218/0x304
...
So clear the bit when failing...
Introduced in c65c9bc3ef (tty: rewrite the ldisc locking) back in
2.6.31-rc1.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Reported-by: Sergey Lapin <slapin@ossfans.org>
Tested-by: Sergey Lapin <slapin@ossfans.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some Lenovos have TPMs that require a quirk to function correctly. This can
be autodetected by checking whether the device has a _HID of INTC0102. This
is an invalid PNPid, and as such is discarded by the pnp layer - however
it's still present in the ACPI code, so we can pull it out that way. This
means that the quirk won't be automatically applied on non-ACPI systems,
but without ACPI we don't have any way to identify the chip anyway so I
don't think that's a great concern.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Tested-by: Jiri Kosina <jkosina@suse.cz>
Tested-by: Andy Isaacson <adi@hexapodia.org>
Signed-off-by: James Morris <jmorris@namei.org>
BugLink: http://bugs.launchpad.net/bugs/441990
This was tested to successfully enable the hardware.
Signed-off-by: John Tapsell <johnflux@gmail.com>
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
CC: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit: "carl9170: revamp carl9170_tx_prepare"
introduced a peculiar bug that would only show
up if the the module parameter noht is set to 1.
Then all outbound voice, video and background
frames would each invoke a (bogus) RTS/CTS
handshake.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
while removing beaconing mode interface, SWBA interrupt
was never disabled when there are no other beaconing interfaces.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With some upcoming changes we'd like to use
the interface types for P2P capability tests.
Enable them now so that when we add those
tests in wpa_supplicant, nothing will break.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath9k driver uses a shared pm_qos_request_list structure for all
devices. This causes the following warning if more than one device is
present in the system:
WARNING: at kernel/pm_qos_params.c:234 ath9k_init_device+0x5e8/0x6b0()
pm_qos_add_request() called for already added request
Modules linked in:
Call Trace:
[<802b1cdc>] dump_stack+0x8/0x34
[<8007dd90>] warn_slowpath_common+0x78/0xa4
[<8007de44>] warn_slowpath_fmt+0x2c/0x38
[<801b0828>] ath9k_init_device+0x5e8/0x6b0
[<801bc508>] ath_pci_probe+0x2dc/0x39c
[<80176254>] pci_device_probe+0x64/0xa4
[<8019471c>] driver_probe_device+0xbc/0x188
[<80194854>] __driver_attach+0x6c/0xa4
[<80193e20>] bus_for_each_dev+0x60/0xb0
[<80193580>] bus_add_driver+0xcc/0x268
[<80194c08>] driver_register+0xe0/0x198
[<801764e0>] __pci_register_driver+0x50/0xe0
[<80365f48>] ath9k_init+0x3c/0x6c
[<8006050c>] do_one_initcall+0xfc/0x1d8
[<80355340>] kernel_init+0xd4/0x174
[<800639a4>] kernel_thread_helper+0x10/0x18
---[ end trace 5345fc6f870564a6 ]---
This patch fixes that warning by using a separate pm_qos_request_list
sructure for each device.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
card->priv must not be accessed after lbs_remove_card() was called
as lbs_remove_card() frees card->priv via free_netdev().
For libertas_sdio this is a regression introduced by 23b149c189.
The correct fix to the issue described there is simply to remove the
assignment. This flag is set at the appropriate time inside
lbs_remove_card anyway.
Reported-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"priv" is stored at the end of the wiphy structure, which is freed
during the call to lbs_cfg_free(). It must not be touched afterwards.
Remove the unnecessary NULL assignment causing this memory corruption.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
eth_type_trans tries to pull data with the length of the ethernet header
from the skb. We only ensured that enough data for the first ethernet
header and the batman header is available in non-paged memory of the skb
and not for the ethernet after the batman header.
eth_type_trans would fail sometimes with drivers which don't ensure that
all there data is perfectly linearised.
The failure was noticed through a kernel bug Oops generated by the
skb_pull inside eth_type_trans.
Reported-by: Rafal Lesniak <lesniak@eresi-project.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We call a lot of the netdevice code when holding if_list_lock which will
spin the whole time. This is not necessary because we only want to
protect the access to the list to be serialized. An extra queue can be
used which hold all interfaces which should be removed and then use that
queue without any locks for netdevice cleanup.
We create a "scheduling while atomic" Oops when calling different
netdevice related functions inside a spinlock protected area on a
preemtible kernel.
Reported-by: Rafal Lesniak <lesniak@eresi-project.org>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Open-source development team extended so contacts updated.
Reviewed-by: Brett Rudley <brudley@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
... otherwise the panel-fitter may be left enabled with random settings
and cause unintended filtering (i.e. blurring of native modes on external
panels).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31942
Reported-and-tested-by: Ben Kohler <bkohler@gmail.com>
Tested-by: Ciprian Docan <docan@eden.rutgers.edu>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The wrong of initializer entry was modified.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Reported-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver's AUTHOR was changed to "Toshiharu Okada" from "Masayuki Ohtake".
I update the Kconfig, renamed "Topcliff" to "EG20T".
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds USB IDs to enable force feedback on the Thrustmaster
F430 wheel.
Antonio did the work, I just converted to git patch to include in Kernel.
Reported-by: Antonio Orefice <aorefice77@gmail.com>
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix two bugs in dirty page logging:
When counting pages we should increase address by 1 instead of
VHOST_PAGE_SIZE. Make log_write() correctly process requests
that cross pages with write_address not starting at page boundary.
Reported-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In order to correctly report monitor connected status changes, the
previous monitor status must be recorded in the connector->status
value instead of being discarded.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When setting a new crtc configuration, force the DPMS state of all
connectors to ON. Otherwise, they'll be left at OFF and a future mode set
that disables the specified connector will not turn the connector off.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In commit 58933c64(ucc_geth: Fix the wrong the Rx/Tx FIFO size),
the UCC_GETH_UTFTT_INIT is set to 512 based on the recommendation
of the QE Reference Manual. But that will sometimes cause tx halt
while working in half duplex mode.
According to errata draft QE_GENERAL-A003(High Tx Virtual FIFO
threshold size can cause UCC to halt), setting UTFTT less than
[(UTFS x (M - 8)/M) - 128] will prevent this from happening
(M is the minimum buffer size).
The patch changes UTFTT back to 256.
Signed-off-by: Li Yang <leoli@freescale.com>
Cc: Jean-Denis Boyer <jdboyer@media5corp.com>
Cc: Andreas Schmitz <Andreas.Schmitz@riedel.net>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds some debug information about ehea not being able to
allocate enough spaces. Also it correctly updates the amount of available
skb.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HSO driver incorrectly creates a serial device instead of a net
device when disable_net is set. It shouldn't create anything for the
network interface.
Signed-off-by: Filip Aben <f.aben@option.com>
Reported-by: Piotr Isajew <pki@ex.com.pl>
Reported-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We register lapb when tty is created, but unregister it only when the
device is UP. So move the lapb_unregister to x25_asy_close_tty after
the device is down.
The old behaviour causes ldisc switching to fail each second attempt,
because we noted for us that the device is unused, so we use it the
second time, but labp layer still have it registered, so it fails
obviously.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Sergey Lapin <slapin@ossfans.org>
Cc: Andrew Hendry <andrew.hendry@gmail.com>
Tested-by: Sergey Lapin <slapin@ossfans.org>
Tested-by: Mikhail Ulyanov <ulyanov.mikhail@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were truncating the number of unicast and multicast MAC addresses
supported. Additionally, we were incorrectly computing the MAC Address
hash (a "1 << N" where we needed a "1ULL << N").
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocating unit from ird might return several error codes
not only -EAGAIN, so it should not be changed and returned
precisely. Same time unit release procedure should be invoked
only if device is unregistering.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
CC: Paul Mackerras <paulus@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
"aup->enable" holds already the address pointing to the MAC enable
register. The bug was introduced by commit d0e7cb:
"au1000-eth: remove volatiles, switch to I/O accessors".
CC: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't track gpu flush request in any special way. So even with
obj->write_domain == 0, a gpu flush might be outstanding but no
yet executed. Even worse, the latest request might use the object
only for reading. So and unconditional call to object_wait_rendering
is needed for !pipelined.
Hence revert that patch fully and untangle the flushing from the
synchronization again.
Reported-by: Keith Packard <keithp@keithp.com>
Tested-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cciss: fix build for PROC_FS disabled
block: fix amiga and atari floppy driver compile warning
blk-throttle: Fix calculation of max number of WRITES to be dispatched
ioprio: grab rcu_read_lock in sys_ioprio_{set,get}()
xen/blkfront: cope with backend that fail empty BLKIF_OP_WRITE_BARRIER requests
xen/blkfront: Implement FUA with BLKIF_OP_WRITE_BARRIER
xen/blkfront: change blk_shadow.request to proper pointer
xen/blkfront: map REQ_FLUSH into a full barrier
Fix kernel-doc warning in fbcmap.c:
Warning(drivers/video/fbcmap.c:92): No description found for parameter 'flags'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'intel/drm-intel-fixes' of /ssd/git/drm-next:
drm/i915/sdvo: Always add a 30ms delay to make SDVO TV detection reliable
MAINTAINERS: INTEL DRM DRIVERS list (intel-gfx) is subscribers-only
drm/i915/sdvo: Always fallback to querying the shared DDC line
drm/i915: Handle pagefaults in execbuffer user relocations
drm/i915/sdvo: Only enable HDMI encodings only if the commandset is supported
drm/i915: Only save/restore cursor regs if !KMS
drm/i915: Prevent integer overflow when validating the execbuffer
This reverts commit d33ef52d9d.
This change seems to expose a bug in the 3D driver tiggered by
certain apps, so revert it to keep userspace working.
Reported-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Incorrect rcu check was used as rcu isn't done
under mutex here. Force check to 1 for now,
to stop it from complaining.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The qdio device indicator is freed before the device is notified that
the indicator is reset. This sequence contains a race when the freed
indicator is used by a new device while the reset of the indicator is
still pending. Do the reset operation before freeing the indicator to
avoid that potential race.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
David Kilroy