IPv6 TSO requests with extension hdrs are a problem to the
Lancer and BEx chips. Workaround is to disable TSO6 feature
for such packets.
Also in Lancer chips, MSS less than 256 was resulting in TX stall.
Fix this by disabling GSO when MSS less than 256.
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
warning: variable ‘netdev’ set but not used
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overlapping changes in drivers/net/phy/marvell.c, bug fix in 'net'
restricting a HW workaround alongside cleanups in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
On certain platforms BE3 chips may indicate spurious UEs (unrecoverable
error). Because of the UE detection logic was disabled in the driver
for BE3 chips. Because of this, even in cases of a real UE,
a failover will not occur. This patch re-enables UE detection on BE3
and if a UE is detected, reads the POST register. If the POST register,
reports either a FAT_LOG_STATE or a ARMFW_UE, then it means that a valid
UE occurred in the chip.
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least some of the be2net cards do not seem to be capabled
of performing checksum offload computions on Q-in-Q packets.
In these case, the recevied checksum on the remote is invalid
and TCP syn packets are dropped.
This patch adds a call to check disbled acceleration features
on Q-in-Q tagged traffic.
CC: Sathya Perla <sathya.perla@broadcom.com>
CC: Ajit Khaparde <ajit.khaparde@broadcom.com>
CC: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
CC: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use time_before_eq for time comparison more safe and dealing
with timer wrapping to be future-proof.
Signed-off-by: Karim Eshapa <karim.eshapa@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We disable VxLAN offload when more than 1 UDP port is added to the driver,
since Skyhawk doesn't support offload with multiple ports. The existing
driver design expects the user to delete all port configurations and create
a configuration with a single UDP port for VxLAN offload to be re-enabled.
Remove this restriction by tracking the ports added and re-enabling offload
when ports get deleted and only 1 port is left.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Reviewed-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use cpu_to_le32() for link_config variable in set_logical_link_config
command as this variable is of type u32.
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compared to custom busy_poll, the generic NAPI one is better, since
it allows to use GRO, and it removes a lot of code and extra locked
operations in fast path.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent commit 3439352916 ("be2net: fix MAC addr setting on privileged
BE3 VFs") allows privileged BE3 VFs to set its MAC address during
initialization. Although the initial MAC for such VFs is already
programmed by parent PF the subsequent setting performed by VF is OK,
but in certain cases (after fresh boot) this command in VF can fail.
The MAC should be initialized only when:
1) no MAC is programmed (always except BE3 VFs during first init)
2) programmed MAC is different from requested (e.g. MAC is set when
interface is down). In this case the initial MAC programmed by PF
needs to be deleted.
The adapter->dev_mac contains MAC address currently programmed in HW so
it should be zeroed when the MAC is deleted from HW and should not be
filled when MAC is set when interface is down in be_mac_addr_set() as
no programming is performed in this case.
Example of failure without the fix (immediately after fresh boot):
# ip link set eth0 up <- eth0 is BE3 PF
be2net 0000:01:00.0 eth0: Link is Up
# echo 1 > /sys/class/net/eth0/device/sriov_numvfs <- Create 1 VF
...
be2net 0000:01:04.0: Emulex OneConnect(be3): VF port 0
# ip link set eth8 up <- eth8 is created privileged VF
be2net 0000:01:04.0: opcode 59-1 failed:status 1-76
RTNETLINK answers: Input/output error
# echo 0 > /sys/class/net/eth0/device/sriov_numvfs <- Delete VF
iommu: Removing device 0000:01:04.0 from group 33
...
# echo 1 > /sys/class/net/eth0/device/sriov_numvfs <- Create it again
iommu: Removing device 0000:01:04.0 from group 33
...
# ip link set eth8 up
be2net 0000:01:04.0 eth8: Link is Up
Initialization is now OK.
v2 - Corrected the comment and condition check suggested by Suresh & Harsha
Fixes: 3439352916 ("be2net: fix MAC addr setting on privileged BE3 VFs")
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ivan Vecera <cera@cera.cz>
Acked-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During interface opening MAC address stored in netdev->dev_addr is
programmed in the HW with exception of BE3 VFs where the initial
MAC is programmed by parent PF. This is OK when MAC address is not
changed when an interfaces is down. In this case the requested MAC is
stored to netdev->dev_addr and later is stored into HW during opening.
But this is not done for all BE3 VFs so the NIC HW does not know
anything about this change and all traffic is filtered.
This is the case of bonding if fail_over_mac == 0 where the MACs of
the slaves are changed while they are down.
The be2net behavior is too restrictive because if a BE3 VF has
the FILTMGMT privilege then it is able to modify its MAC without
any restriction.
To solve the described problem the driver should take care about these
privileged BE3 VFs so the MAC is programmed during opening. And by
contrast unpriviled BE3 VFs should not be allowed to change its MAC
in any case.
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
BE3 VFs without FILTMGMT privilege are not allowed to modify its MAC,
VLAN table and UC/MC lists. So don't try to delete MAC on such VFs.
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return value from be_mcc_notify_wait() contains a base completion status
together with an additional status. The base_status() macro need to be
used to access base status.
Fixes: e3a7ae2 be2net: Changing MAC Address of a VF was broken
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The adapter->pmac_id[0] item is used for primary MAC address but
this is not true for adapter->uc_list[0] as is assumed in
be_set_uc_list(). There are N UC addresses copied first from net_device
to adapter->uc_list[1..N] and then N UC addresses from
adapter->uc_list[0..N-1] are sent to HW. So the last UC address is never
stored into HW and address 00:00:00:00;00:00 (from uc_list[0]) is used
instead.
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Fixes: b717241 be2net: replace polling with sleeping in the FW completion path
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 988d44b "be2net: Avoid redundant addition of mac address in HW"
introduced be_dev_mac_add & be_uc_mac_add helpers that incorrectly
access adapter->uc_list as an array of bytes instead of an array of
be_eth_addr. Consequently NIC is not filled with valid data so unicast
filtering is broken.
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Fixes: 988d44b be2net: Avoid redundant addition of mac address in HW
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VXLAN offloading is enabled, be_features_check() tries to check if
an encapsulated packet is indeed a VXLAN packet. The check is not strict
enough, and considers any UDP-encapsulated ethernet frame with a 8-byte
tunnel header as being VXLAN. Unfortunately, both GENEVE and VXLAN-GPE
have a 8-byte header, so they get through this check.
Force the UDP destination port to be the one that has been offloaded to
hardware.
Without this, GENEVE-encapsulated packets can end up having an incorrect
checksum when both a GENEVE and a VXLAN (offloaded) tunnel are
configured.
This is similar to commit a547224dce ("mlx4e: Do not attempt to
offload VXLAN ports that are unrecognized").
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently allocates 128 bytes of skb headroom.
This was found to be insufficient with some configurations
like Geneve tunnels, which resulted in skb head reallocations.
Increase the headroom to 256 bytes to fix this.
Signed-off-by: Kalesh A P <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OPCODE_COMMON_GET_FN_PRIVILEGES is returning only DEVSEC
privilege (Unrestricted Administrative Privilege) for Lancer NIC functions.
So, driver is failing SET_HSW_CONFIG command, as DEVSEC privilege was not
set in the privilege bitmap. This patch fixes the problem by setting DEVSEC
privilege in SET_HSW_CONFIG’s privilege bitmap.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling napi_hash_del() before netif_napi_del() is dangerous
if a synchronize_rcu() is not enforced before NAPI struct freeing.
Lets leave this detail to core networking stack and feel
more comfortable.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somehow, I missed a healthy number of ethernet drivers in the last pass.
Most of these drivers either were in need of an updated max_mtu to make
jumbo frames possible to enable again. In a few cases, also setting a
different min_mtu to match previous lower bounds. There are also a few
drivers that had no upper bounds checking, so they're getting a brand new
ETH_MAX_MTU that is identical to IP_MAX_MTU, but accessible by includes
all ethernet and ethernet-like drivers all have already.
acenic:
- min_mtu = 0, max_mtu = 9000
amazon/ena:
- min_mtu = 128, max_mtu = adapter->max_mtu
amd/xgbe:
- min_mtu = 0, max_mtu = 9000
sb1250:
- min_mtu = 0, max_mtu = 1518
cxgb3:
- min_mtu = 81, max_mtu = 65535
cxgb4:
- min_mtu = 81, max_mtu = 9600
cxgb4vf:
- min_mtu = 81, max_mtu = 65535
benet:
- min_mtu = 256, max_mtu = 9000
ibmveth:
- min_mtu = 68, max_mtu = 65535
ibmvnic:
- min_mtu = adapter->min_mtu, max_mtu = adapter->max_mtu
- remove now redundant ibmvnic_change_mtu
jme:
- min_mtu = 1280, max_mtu = 9202
mv643xx_eth:
- min_mtu = 64, max_mtu = 9500
mlxsw:
- min_mtu = 0, max_mtu = 65535
- Basically bypassing the core checks, and instead relying on dynamic
checks in the respective switch drivers' ndo_change_mtu functions
ns83820:
- min_mtu = 0
- remove redundant ns83820_change_mtu, only checked for mtu > 1500
netxen:
- min_mtu = 0, max_mtu = 8000 (P2), max_mtu = 9600 (P3)
qlge:
- min_mtu = 1500, max_mtu = 9000
- driver only supports setting mtu to 1500 or 9000, so the core check only
rules out < 1500 and > 9000, qlge_change_mtu still needs to check that
the value is 1500 or 9000
qualcomm/emac:
- min_mtu = 46, max_mtu = 9194
xilinx_axienet:
- min_mtu = 64, max_mtu = 9000
Fixes: 61e84623ac ("net: centralize net_device min/max MTU checking")
CC: netdev@vger.kernel.org
CC: Jes Sorensen <jes@trained-monkey.org>
CC: Netanel Belgazal <netanel@annapurnalabs.com>
CC: Tom Lendacky <thomas.lendacky@amd.com>
CC: Santosh Raspatur <santosh@chelsio.com>
CC: Hariprasad S <hariprasad@chelsio.com>
CC: Sathya Perla <sathya.perla@broadcom.com>
CC: Ajit Khaparde <ajit.khaparde@broadcom.com>
CC: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
CC: Somnath Kotur <somnath.kotur@broadcom.com>
CC: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
CC: John Allen <jallen@linux.vnet.ibm.com>
CC: Guo-Fu Tseng <cooldavid@cooldavid.org>
CC: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
CC: Jiri Pirko <jiri@mellanox.com>
CC: Ido Schimmel <idosch@mellanox.com>
CC: Manish Chopra <manish.chopra@qlogic.com>
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Rajesh Borundia <rajesh.borundia@qlogic.com>
CC: Timur Tabi <timur@codeaurora.org>
CC: Anirudha Sarangi <anirudh@xilinx.com>
CC: John Linn <John.Linn@xilinx.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VF link state setting feature now works on BE3 chips too from
FW ver 11.1.192.0 onwards.
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX stats update does not take into account headers which get duplicated
when the TSO packet is split into segments by HW. Fix this for both
tunneled (vxlan) and non-tunneled TSO packets.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the year and company name in the copyright string
in be_hw.h.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver has a check to ensure that NCSI FW section is updated only
if the current FW version in the card supports it. This FW version check
is done using memcmp() which obviously fails in some cases. Fix this by
breaking up the version string into integer version components and
comparing them.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver gets the pf_num for Skyhawk and Lancer using
GET_FUNC_CONFIG FW command. But since that command is not
supported in BEx, we need to get it from some other command.
Otherwise TPE recovery would fail since all NIC PFs would
end up with a func num of 0. There's a pci function number
field in the response of GET_CNTL_ATTRIBUTES command that
can be read to get the same info for BEx adapters.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warnings:
drivers/net/ethernet/emulex/benet/be_main.c:47:25: warning:
symbol 'be_err_recovery_workq' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_main.c:63:25: warning:
symbol 'be_wq' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new rtnl UAPI that exposes a list of vlans per VF, giving
the ability for user-space application to specify it for the VF, as an
option to support 802.1ad.
We adjusted IP Link tool to support this option.
For future use cases, the new UAPI supports multiple vlans. For now we
limit the list size to a single vlan in kernel.
Add IFLA_VF_VLAN_LIST in addition to IFLA_VF_VLAN to keep backward
compatibility with older versions of IP Link tool.
Add a vlan protocol parameter to the ndo_set_vf_vlan callback.
We kept 802.1Q as the drivers' default vlan protocol.
Suitable ip link tool command examples:
Set vf vlan protocol 802.1ad:
ip link set eth0 vf 1 vlan 100 proto 802.1ad
Set vf to VST (802.1Q) mode:
ip link set eth0 vf 1 vlan 100 proto 802.1Q
Or by omitting the new parameter
ip link set eth0 vf 1 vlan 100
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get 4 warnings when building kernel with W=1:
drivers/net/ethernet/emulex/benet/be_main.c:4368:6: warning: no previous prototype for 'be_calculate_pf_pool_rss_tables' [-Wmissing-prototypes]
drivers/net/ethernet/emulex/benet/be_cmds.c:4385:5: warning: no previous prototype for 'be_get_nic_pf_num_list' [-Wmissing-prototypes]
drivers/net/ethernet/emulex/benet/be_cmds.c:4537:6: warning: no previous prototype for 'be_reset_nic_desc' [-Wmissing-prototypes]
drivers/net/ethernet/emulex/benet/be_cmds.c:4910:5: warning: no previous prototype for '__be_cmd_set_logical_link_config' [-Wmissing-prototypes]
In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
so this patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the device mac address is updated using ndo_set_mac_address(),
while the same mac address is already programmed, the driver does not
detect this condition if its netdev->dev_addr has been changed. The
driver tries to add the same mac address resulting in mac address
collision error. This has been observed in bonding mode-5 configuration.
To fix this, store the mac address configured in HW in the adapter
structure. Use this to compare against the new address being updated
to avoid collision.
Signed-off-by: Suresh Reddy <Suresh.Reddy@broadcom.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a mac address is added to the uc_list and later the same mac address
is added via ndo_set_mac_address() or vice versa, the driver does not
detect this condition and tries to add it again. This results in a mac
address collision error when the FW rejects it.
Fix this by checking if the given mac address is present in uc_list while
setting the device mac address and vice versa. Similarly skip deletion if
the address is still in use in the other form.
Signed-off-by: Suresh Reddy <Suresh.Reddy@broadcom.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver issues OPCODE_COMMON_GET_EXT_FAT_CAPABILITIES cmd during init which
when issued by VFs results in the logging of a cmd failure message since
they don't have the required privilege for this cmd. Fix by checking
privilege before issuing the cmd.
Also fixed typo in CAPABILITIES.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per SLI guideline, drivers need to issue COMMON_RESET_FUNCTION SLI
cmd during driver unload to clean up any non-persistent state
information.
Issue this cmd only if VFs are not assigned to VMs as it is possible
for PF driver to unload while it\'s VF remains functional and assigned
to a VM.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch supports recovery from UEs caused due to Transient Parity
Errors (TPE), in BE2, BE3 and Skyhawk adapters. This change avoids
system reboot when such errors occur. The driver recovers from these
errors such that the adapter resumes full operational status as prior
to the UE.
Following is the list of changes in the driver to support this:
o The driver registers its UE recoverable capability with ARM FW at init
time. This also allows the driver to know if the feature is supported in
the FW.
o As the UE recovery requires precise time bound processing, the driver
creates its own error recovery work queue with a single worker thread (per
module, shared across functions).
o Each function runs an error detection task at an interval of 1 second as
required by the FW. The error detection logic already exists for BEx/SH,
but it now runs in the context of a separate worker thread.
o When an error is detected by the task, if it is recoverable, the PF0
driver instance initiates a soft reset, while other PF driver instances
wait for the reset to complete and the chip to become ready. Once
the chip is ready, all driver instances including PF0, resume to
reinitialize the respective functions.
o The PF0 driver checks for some recovery criteria, to determine if the
recovery can be initiated. If the criteria is not met, the PF0 driver does
not initiate a soft reset, it retains the existing behavior to stop
further processing and requires a reboot to get the chip to operational
state again.
o To allow each function to share the workq, while also making progress in
its recovery process, a per-function recovery state machine is used.
The per-function tasks avoid blocking operations like msleep() while in
this state machine (until reinit state) and instead reschedule for the
required delay.
o With these changes, the existing error recovery code for Lancer also
runs in the context of the new worker thread.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ndo_set_rx_mode() and ndo_add/del_vxlan_port() calls may be called with
BHs disabled. The driver currently issues the required cmds to the FW in
these contexts and polls on completions from the FW, while BHs remain
disabled. This can cause either packet loss or packet reception to be
delayed on that CPU.
This patch defers processing of the above cmds to a separate workqueue.
With this change, FW cmds are now issued only in process context.
Now that the FW cmds are issued only in process context, they can sleep
waiting for a completion instead of polling. All the spin_lock_bh(mcc_lock)
calls are now replaced with mutex calls.
Also a new rx_filter_lock is now needed to protect the RX filtering fields
like vids[] between be_vlan_add/rem_vid() and __be_set_rx_mode() contexts.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eachtime the ndo_set_rx_mode() routine is called, the driver programs the
multicast list in the adapter without checking if there are any changes to
the list. This leads to a flood of RX_FILTER cmds when a number of vlan
interfaces are configured over the device, as the ndo_ gets
called for each vlan interface. To avoid this, we now use __dev_mc_sync()
and __dev_uc_sync() API, but only to detect if there is a change in the
mc/uc lists. Now that we use this API, the code has to be-designed to
issue these API calls for each invocation of the be_set_rx_mode() call.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently removes a new vid from the adapter->vids[] array if
be_vid_config() returns an error, which occurs when there is an error in
HW/FW. This is wrong. After the HW/FW error is recovered from, we need the
complete vids[] array to re-program the vlan list.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Lancer FW has a bug due to which in some cases vlan-promisc setting
is cleared eventhough the vlan-list programming did not succeed (via
VLAN_CONFIG) cmd. The driver has no way of knowing if the vlan-promisc
mode was cleared or not when this cmd fails. To work around this issue,
this patch first explicitly clears the vlan-promisc mode via RX_FILTER
cmd and then tries to program the vlan list.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The be2net driver performs fw temperature queries on be_worker() routine,
which is executed each second for each be_adapter. There is a frequency
threshold to avoid fw query to happens at each call to be_worker();
instead, currently a fw query occurs once in 64 runs of the procedure.
Nevertheless, this fw temperature query is invoked only for adapters which
interface is up, so we can see I/O errors on read of hwmon counters from
userspace (from tools like lm-sensors) in case we have adapters' functions
which interface is down.
This patch moves the fw query code to be invoked even if interface is down.
No functional changes were introduced.
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"num_vec" needs to be signed for the error handling to work.
Fixes: e261768e9e ('be2net: support asymmetric rx/tx queue counts')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suresh Reddy