Make use of enum chips and use a switch statement in load_attenuators()
so that the compiler can tell us if we've failed to cater for a
supported chip.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220323034056.260455-4-chris.packham@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The adt7473, adt7475, adt7476 and adt7490 have pins that can be used for
different functions. On the adt7473 and adt7475 this is pins 5 and 9.
On the adt7476 and adt7490 this is pins 10 and 14.
The first pin can either be PWM2(default) or SMBALERT#. The second pin
can be TACH4(default), THERM#, SMBALERT# or GPIO.
The adt7475 driver has always been able to detect the configuration if
it had been done by an earlier boot stage. Add support for configuring
the pins based on the hardware description in the device tree.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220323034056.260455-3-chris.packham@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Many hwmon drivers don't use the id information provided by the old
i2c probe function, and the remainder can easily be adapted to the new
form ("probe_new") by calling i2c_match_id explicitly.
This avoids scanning the identifier tables during probes.
Drivers which didn't use the id are converted as-is; drivers which did
are modified as follows:
* if the information in i2c_client is sufficient, that's used instead
(client->name);
* anything else is handled by calling i2c_match_id() with the same
level of error-handling (if any) as before.
A few drivers aren't included in this patch because they have a
different set of maintainers. They will be covered by other patches.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813160222.1503401-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add a "adi,pwm-active-state" device-tree property to allow hardware
designs to use inverted logic on the PWM output.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
[groeck: dev_err -> dev_warn]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Added support for reading DTS properties to set attenuators on
device probe for the ADT7473, ADT7475, ADT7476, and ADT7490.
Signed-off-by: Logan Shaw <logan.shaw@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
[groeck: Continuation line formatting; dev_err -> dev_warn]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
reg2volt returns the voltage that matches a given register value.
Converting this back the other way with volt2reg didn't return the same
register value because it used truncation instead of rounding.
This meant that values read from sysfs could not be written back to sysfs
to set back the same register value.
With this change, volt2reg will return the same value for every voltage
previously returned by reg2volt (for the set of possible input values)
Signed-off-by: Luuk Paulussen <luuk.paulussen@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20191205231659.1301-1-luuk.paulussen@alliedtelesis.co.nz
cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
hwmon_device_register() is a deprecated function and produces a warning.
Converting the driver to use the hwmon_device_register_with_groups()
instead.
Signed-off-by: Grant McEwan <grant.mcewan@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20190721225530.28799-2-grant.mcewan@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_OF is not enabled, the following build warning is observed.
drivers/hwmon/adt7475.c:171:34: warning:
‘adt7475_of_match’ defined but not used
Mark adt7475_of_match as __maybe_unused to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use SENSOR[_DEVICE]_ATTR[_2]_{RO,RW,WO} to simplify the source code,
to improve readbility, and to reduce the chance of inconsistencies.
Also replace any remaining S_<PERMS> in the driver with octal values.
The conversion was done automatically with coccinelle. The semantic patches
and the scripts used to generate this commit log are available at
https://github.com/groeck/coccinelle-patches/hwmon/.
This patch does not introduce functional changes. It was verified by
compiling the old and new files and comparing text and data sizes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The adt7475_read_word() function was meant to return negative error
codes on failure.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The adt7475_update_device() function returns error pointers. The
problem is that in show_pwmfreq() we dereference it before the check.
And then in pwm_use_point2_pwm_at_crit_show() there isn't a check at
all. I don't know if it's required, but it silences a static checker
warning and it's doesn't hurt anything to check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Change update device function to return an error pointer if needed,
and report the error to user space.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
[groeck: Clarified/updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
I2C SMBus sometimes returns error codes.
In the error case, measurement values are updated incorrectly.
The sensor application then generates warning log messages and SNMP traps.
To prevent this, add error handling into the update functions.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
[groeck: Update description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Currently the valid variable is of type char, but it is used as boolean.
So let's change it to bool.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
[groeck: Update description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The update function reads both measurement and limit values.
Those parts can be split so split them for a maintainability.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
[groeck: Clarify description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
10055 7032 0 17087 42bf drivers/hwmon/adt7475.o
File size After adding 'const':
text data bss dec hex filename
10567 6520 0 17087 42bf drivers/hwmon/adt7475.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When enabled temperature smoothing allows ramping the fan speed over a
configurable period of time instead of jumping to the new speed
instantaneously.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Systems using 4-wire fans usually require high frequency (22.5kHz)
output on the pwm. Add 22500 as a valid option in the pwmfreq_table. In
high frequency mode the low-order bit are ignored so they can safely be
set to 0.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
By default adt7475 will stop the fans (pwm duty cycle 0%) when the
temperature drops past Tmin - hysteresis. Some systems want to keep the
fans moving even when the temperature drops so add new sysfs attributes
that configure the enhanced acoustics min 1-3 which allows the fans to
run at the minimum configure pwm duty cycle.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The adt7475 has had find_nearest() since it's creation in 2009. Since
then find_closest() has been introduced and several drivers have been
updated to use it. Update the adt7475 to use find_closest() and remove
the now unused find_nearest().
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ADT7475 and ADT7476 have the STRT bit cleared by default[1]. Before any
monitoring activities the STRT bit needs to be set. Logically this needs
to happen before any of the sensors are read so the probe() function
seems the best place for it.
[1] - https://www.onsemi.com/pub/Collateral/ADT7475-D.PDF
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
SENSORS_LIMIT and the generic clamp_val have the same functionality,
and clamp_val is more efficient.
This patch reduces text size by 9052 bytes and bss size by 11624 bytes
for x86_64 builds.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: George Joseph <george.joseph@fairview5.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Many hwmon drivers use jiffies but omit the inclusion of the header
file. Fix that, and also fix one driver which was including the header
file but didn't need it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Luca Tettamanti <kronos.it@gmail.com>
Cc: Marc Hulsman <m.hulsman@tudelft.nl>
Cc: Rudolf Marek <r.marek@assembler.cz>
Convert to use devm_ functions to reduce code size and simplify the code.
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
This patch converts the drivers in drivers/hwmon/* to use the
module_i2c_driver() macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Corentin Labbe <corentin.labbe@geomatys.fr>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: Riku Voipio <riku.voipio@iki.fi>
Cc: Guillaume Ligneul <guillaume.ligneul@gmail.com>
Cc: David George <david.george@ska.ac.za>
Cc: "Hans J. Koch" <hjk@hansjkoch.de>
Cc: Marc Hulsman <m.hulsman@tudelft.nl>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
replaced strict_strtol with kstrtol and
replaced strict_strtuol with kstrtuol
This satisfies checkpatch -f
Compile tested only: no warnings or errors given
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
We can mark normal_i2c const. Almost all drivers do that already, so
fix the 3 remaining ones before they are used as (bad) examples for
new drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: George Joseph <george.joseph@fairview5.com>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
These macros simply declare an enum, so drivers might as well declare
it themselves. This puts an end to the arbitrary limit of 8 chip types
per i2c driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Struct i2c_client_address_data only contains one field at this point,
which makes its usefulness questionable. Get rid of it and pass simple
address lists around instead.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
The "kind" parameter always has value -1, and nobody is using it any
longer, so we can remove it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
The ADT7476 has 5 dedicated pins for VID input, and the +12V input can
optionally be used as a 6th VID pin. Add support for VID input.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Add support for the Analog Devices ADT7476 chip. This chip is largely
compatible with the ADT7473 and ADT7475, with additional features.
In particular, it has 5 voltage inputs instead of 2, and VID input
pins.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
It is possible to bypass the voltage attenuators on the +2.5V, Vccp,
+5V and +12V voltage monitoring inputs. This is useful to connect
other voltage channels than the ones the monitoring chip was
originally designed for. When this feature is enabled, we must not
include the scaling factors in our computations.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Print the device name and revision at probe time, as well as a list of
all optional features which are available.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
The TACH4 pin can be used for other functions, so fan4 may not always
be available. Likewise, the PWM2 pin can be used for ALERT output, in
which case pwm2 is not available
For the ADT7490, the +2.5 Vin pin may also be used for other
functions, in which case in0 is not available.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Move sysfs files removal to a separate function. The code is common to
the device probing error path and the standard device removal path. As
it will grow with future driver development, this avoids code
duplication.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Add support for the Analog Devices ADT7490 chip. This chip is largely
compatible with the ADT7473 and ADT7475, with additional features.
In particular, it has 6 voltage inputs instead of 2.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Check the value of register 0x3f as part of the device detection, to
make it more robust.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
adt7475_attr_group is used internally only and can thus be marked
static.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Rework the handling of voltage inputs to make it possible and easy to
support more inputs. This will be needed for the upcoming ADT7490
support.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Implement the non-standard pwm_use_point2_pwm_at_crit sysfs attribute
as the adt7473 driver did.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Add support for the ADT7473 to the adt7475 driver, and mark the
adt7473 driver for removal. The ADT7473 and ADT7475 chips are almost
the same chip and essentially compatible, so there's no point in
having separate drivers for them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
As kind is now hard-coded to -1, there is room for code clean-ups.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Corentin Labbe <corentin.labbe@geomatys.fr>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Juerg Haefliger <juergh@gmail.com>
Cc: Riku Voipio <riku.voipio@iki.fi>
Acked-by: "Hans J. Koch" <hjk@linutronix.de>
Cc: Rudolf Marek <r.marek@assembler.cz>
The adt7475 driver creates pwm#_auto_channel_temp attributes instead
of the standard pwm#_auto_channels_temp. Fix it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Chris Packham