The chip type distinction is getting more and more relevant and
complicating, so always print the chip type.
Printing a name string is also much better than just printing an
internal index number.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need for two else-if constructs for the type_1 chip
detection in pl2303_startup(), so merge them.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function dma_set_mask() tests internally whether the dma_mask pointer
for the device is initialized and fails if the dma_mask pointer is NULL.
On pci platforms, the device dma_mask pointer is initialized, when pci
devices are enumerated, to point to the pci_dev->dma_mask which is 0xffffffff.
However, for non-pci platforms, the dma_mask pointer may not be initialized
and in that case dma_set_mask() will fail.
This patch initializes the dma_mask and the coherent_dma_mask to 32bits
in xhci_plat_probe(), before the call to usb_create_hcd() that sets the
"uses_dma" flag for the usb bus and the call to usb_add_hcd() that creates
coherent dma pools for the usb hcd.
Moreover, a call to dma_set_mask() does not set the device coherent_dma_mask.
Since the xhci-hcd driver calls dma_alloc_coherent() and dma_pool_alloc()
to allocate consistent DMA memory blocks, the coherent DMA address mask
has to be set explicitly.
This patch sets the coherent_dma_mask to 64bits in xhci_gen_setup() when
the xHC is capable for 64-bit DMA addressing.
If dma_set_mask() succeeds, for a given bitmask, it is guaranteed that
the given bitmask is also supported for consistent DMA mappings.
Other changes introduced in this patch are:
- The return value of dma_set_mask() is checked to ensure that the required
dma bitmask conforms with the host system's addressing capabilities.
- The dma_mask setup code for the non-primary hcd was removed since both
primary and non-primary hcd refer to the same generic device whose
dma_mask and coherent_dma_mask are already set during the setup of
the primary hcd.
- The code for reading the HCCPARAMS register to find out the addressing
capabilities of xHC was removed since its value is already cached in
xhci->hccparams.
- hcd->self.controller was replaced with the dev variable since it is
already available.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch defines a new trace event, which is called xhci_dbg_ring_expansion
and belongs to the event class xhci_log_msg, and adds tracepoints that trace
the debug messages associated with the expansion of endpoint ring when there
is not enough space allocated to hold all pending TRBs.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch defines a new trace event, which is called xhci_dbg_init
and belongs to the event class xhci_log_msg, and adds tracepoints that
trace the debug statements in the functions used to start and stop the
xhci-hcd driver.
Also, it removes an unnecessary cast of variable val to unsigned int
in xhci_mem_init(), since val is already declared as unsigned int.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch defines a new trace event, which is called xhci_dbg_cancel_urb
and belongs to the event class xhci_log_msg, and adds tracepoints that
trace the debug messages related to the removal of a cancelled URB from
the endpoint's transfer ring.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch creates a new event class, called xhci_log_event,
and defines the xhci_cmd_completion trace event used for
tracing the commands issued to xHC that generate a completion
event in the event ring.
This info can be used, later, to print, in a human readable
way, the completion status and flags as well as the command's
type and fields using the trace-cmd tool and the appropriate
plugin.
Also, a tracepoint is added in handle_cmd_completion().
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch defines a new event class, called xhci_log_ctx,
that records in the ring buffer the context data, the
context type (input or output), the context dma and virtual
addresses, the context endpoint entries, the slot ID and
whether the xHC uses 64 byte context data structures.
This information can be used, later, to parse and display
the context data fields with the appropriate plugin using
the trace-cmd tool.
Also, this patch defines a trace event, called xhci_address_ctx,
to trace the contexts related to the Address Device command and
adds the associated tracepoints in xhci_address_device().
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch defines a new trace event, which is called xhci_dbg_reset_ep
and belongs in the event class xhci_log_msg, and adds tracepoints that
trace the debug messages associated with resetting an endpoint after
the reception of a STALL packet.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch defines a new trace event, which is called xhci_dbg_quirks
and belongs in the event class xhci_log_msg, and adds tracepoints that
trace the debug messages associated with xHCs' quirks.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch defines a new trace event, which is called xhci_dbg_context_change
and belongs in the event class xhci_log_msg, and adds tracepoints for tracing
the debug messages related to context updates performed with Configure Endpoint
and Evaluate Context commands.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch declares an event class for trace events that
trace messages with variadic arguments, called xhci_log_msg,
and defines a trace event for tracing the debug messages in
xhci_address_device() function, called xhci_dbg_address.
In order to implement this type of trace events, a wrapper function,
called xhci_dbg_trace(), was created that records the format string
and variadic arguments into a va_format structure which is passed as
argument to the tracepoints of the class xhci_log_msg.
All the xhci_dbg() calls in xhci_address_device() are replaced
with calls to xhci_dbg_trace(). The functionality of xhci_dbg()
log messages was not removed though, but it is placed inside
xhci_dbg_trace().
This trace event aims to give the ability to the user or the
developper to isolate and trace the debug messages generated
when an Address Device Command is issued to xHC.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CONFIG_USB_XHCI_HCD_DEBUGGING option is used to enable
verbose debugging output for the xHCI host controller
driver.
In the current version of the xhci-hcd driver, this
option must be turned on, in order for the debugging
log messages to be displayed, and users may need to
recompile the linux kernel to obtain debugging
information that will help them track down problems.
This patch removes the above debug option to enable
debugging log messages at all times.
The aim of this is to rely on the debugfs and the
dynamic debugging feature for fine-grained management
of debugging messages and to not force users to set
the debug config option and compile the linux kernel
in order to have access in that information.
This patch, also, removes the XHCI_DEBUG symbol and the
functions dma_to_stream_ring(), xhci_test_radix_tree()
and xhci_event_ring_work() that are not useful anymore.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch replaces the calls to printk(KERN_DEBUG ...)
with either calls to xhci_dbg() or calls to pr_debug(),
depending on whether the xhci_hcd structure is available
at callsite, so that the correspoding debugging messages
are not enabled by default when CONFIG_DYNAMIC_DEBUG option
is set but rather can be enabled dynamically taking advantage
of the dynamic debugging feature.
Also, it adds a newline at the end of debugging messages in
case there is not, so that messages don't appear broken
when printed.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch replaces the calls to xhci_info() with calls to
xhci_dbg() and removes the unused xhci_info() definition
from xhci-hcd.
By replacing the xhci_info() with xhci_dbg(), the calls to
dev_info() are replaced with calls to dev_dbg() so that
their output can be dynamically controlled via the dynamic
debugging mechanism.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Add Device Tree match table to xhci-plat.c. Add DT bindings document.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
All patches here have been pending on linux-usb
and sitting in linux-next for a while now.
The biggest things in this tag are:
DWC3 learned proper usage of threaded IRQ
handlers and now we spend very little time
in hardirq context.
MUSB now has proper support for BeagleBone and
Beaglebone Black.
Tegra's USB support also got quite a bit of love
and is learning to use PHY layer and generic DT
attributes.
Other than that, the usual pack of cleanups and
non-critical fixes follow.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=3NS9
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.12 merge window
All patches here have been pending on linux-usb
and sitting in linux-next for a while now.
The biggest things in this tag are:
DWC3 learned proper usage of threaded IRQ
handlers and now we spend very little time
in hardirq context.
MUSB now has proper support for BeagleBone and
Beaglebone Black.
Tegra's USB support also got quite a bit of love
and is learning to use PHY layer and generic DT
attributes.
Other than that, the usual pack of cleanups and
non-critical fixes follow.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Conflicts:
drivers/usb/gadget/udc-core.c
drivers/usb/host/ehci-tegra.c
drivers/usb/musb/omap2430.c
drivers/usb/musb/tusb6010.c
Stephen Rothwell reported that this driver does not compile on PowerPC
due to this missing include. One could argue why this driver is enabled
on PowerPC in the first place but it sure isn't wrong to include headers
for used function instead of to rely that they sneak in.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since the musb-gadget code now calls the dma engine properly it is
possible to enable it for the TX path in device mode.
AM335x Advisory 1.0.13 says that we may lose the toggle bit on multiple
RX transfers. There is a workaround in host mode but none in device mode
and therefore RX transfers are disabled.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch makes use of the two function is_cppi_enabled() and
tusb_dma_omap() instead of the ifdef for the proper DMA implementation
setup code. It basically shifts the code right by one indention level
and adds a few line breaks once the chars are crossed.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
I've found some new datasheets which describe some additionally
supported standard baud rates and I've verified them with my HX
(rev. 3A) device. But adding support for individual (chip type
specific) baud rates would add a good amount of extra code (especially
when support for further chips will be added to the driver one day),
which makes no sense as long as we are not using the direct baud rate
encoding method for newer chips.
So for now, just drop a comment about these additionally supported baud
rates.
The second comment is about the baud rate differences between the two
encoding methods. In theory, we could optimize the code a bit by
comparing the resulting baud rates of both methods and selecting the
one which is closer to the requested baud rate. But that seems to be a
bit overkill, because the differences are very small and the device
likely uses the same baud rate generator for both methods so that the
resulting baud rate would be the same.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the divisor based baud rate encoding method has been fixed and
extended, it can also be used for baud rates < 115200 baud with HX
chips.
This makes it possible to adjust the baud rate almost continuously
instead of just beeing able to select between 16 fixed standard values.
Tested with a PL2303HX 04463A (week 46, 2004, rev 3A).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reinhard Max has done some tests with a PL2303HX (rev A) and a logic
analyzer and it seems, that although the PL2303HX is specified for baud
rates from 75 to 6M baud, the full divisor range can be used with the
divisor based baud rate encoding method. This corresponds to baud rates
from 46 to 24M baud.
Baud rates down to 46 baud (max. divisor) have been confirmed to work
even under heavy/permanent load, so remove the lower limit.
Baud rates up to 24M baud should really be tested carefully in "real
life" scenarios before removing the upper limit completely.
Anyway, the Windows driver allows maximum baud rates of 110% of the
specified limit, so for now, increase the upper limit to this value.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Reinhard Max <max@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 0c967e7e "USB: serial: pl2303 works at 500kbps" added 500000
baud to the list of supported standard baud rates.
But the reason why the driver works with this baud rate is, that since
commit 8d48fdf6 "USB: PL2303: correctly handle baudrates above 115200"
a second (divisor based) baud rate encoding method is used for values
above 115200 baud, which is not limited to a fixed set of standard baud
rates.
Remove the 500000 baud value from the list of standard baud rates
again, because this list is only used with the direct baud rate
encoding method and 500000 baud is not supported with this method.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In opposition to the direct baud rate encoding method, the divisor
based method is not limited to a fixed set of standard baud rates.
Hence, there is no need to round to the next nearest standard value.
Reported-by: Mastro Gippo <gipmad@gmail.com>
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Reinhard Max <max@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on the formula in the code description, Reinhard Max and me have
investigated the devices behavior / functional principle of the divisor
based baud rate encoding method.
It turned out, that (although beeing a good starting point) the current
code has some flaws. It doesn't work correctly for a wide range of baud
rates and the divisor resolution can be improved. It also doesn't
report the actually set baud rate.
This patch fixes and improves the code for the divisor based baud rate
encoding method a lot. It can now be used for the whole range of baud
rates from 46 baud to 24M baud with a very good divisor resolution and
userspace can read back the resulting baud rate.
It also documents the formula used for encoding and the hardware
behavior (including special cases).
The basic algorithm, rounding and several code comments/explanations
are provided by Reinhard Max.
I've added some minor fixes, the handling of the special cases and
further code/algorithm descriptions.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Reinhard Max <max@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prevent the USB core from suspending the HWA root hub since bus_suspend
and bus_resume are not yet supported. Otherwise the PM system will chew
up CPU time constantly attempting to suspend and resume the root hub but
never succeeding.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both could want to submit the same URB. Some checks of the flag
intended to prevent that were missing.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix endianess bugs in firmware handling introduced by commits cb7a7c6a
("ti_usb_3410_5052: add Multi-Tech modem support") and 05a3d905
("ti_usb_3410_5052: support alternate firmware") which made the driver
use the wrong firmware for certain devices on big-endian machines.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure the reported device-type on big-endian machines is the same as
on little-endian ones.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix probe of Rigol devices on big-endian machines. A quirk for these
devices was introduced by commit c2e314835 ("USB: usbtmc: Set
rigol_quirk if device is listed") but was only enabled on little-endian
machines.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix bug in device-type detection on big-endian machines originally
introduced by commit 0eafe4de ("USB: serial: mos7840: add support for
MCS7810 devices") which always matched on little-endian product ids.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes an issue where the bulk-in urb used for incoming data transfer
is not resubmitted if the packet recieved contains an error status. This
results in the driver locking until the port is closed and re-opened.
Tested on a custom board with a Cinterion GSM module.
Signed-off-by: Matt Burtch <matt@grid-net.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a kernel panic that can occur when disconnecting a
wireless USB->serial device. When the serial device disconnects, the
device cleanup procedure ends up calling usb_hcd_disable_endpoint on the
serial device's endpoints. The wusbcore uses the ABORT_RPIPE command to
abort all transfers on the given endpoint but it does not properly give
back the URBs when the transfer results return from the HWA. This patch
prevents the transfer result processing code from bailing out when it sees
a WA_XFER_STATUS_ABORTED result code so that these urbs are flushed
properly by usb_hcd_disable_endpoint. It also updates wa_urb_dequeue to
handle the case where the endpoint has already been cleaned up when
usb_kill_urb is called which is where the panic originally occurred.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commits 4005ad4390 (EHCI: implement new semantics for
URB_ISO_ASAP) and c75c5ab575 (ALSA: USB: adjust for changed 3.8 USB
API) became widely distributed, people have been experiencing problems
with audio transfers. The slightest underrun causes complete failure,
requiring the audio stream to be restarted.
It turns out that the current isochronous API doesn't handle underruns
in the best way. The ALSA developers would much rather have transfers
that are submitted too late be accepted and complete in the normal
fashion, rather than being refused outright.
This patch implements the requested approach. When an isochronous URB
submission is so late that all its scheduled slots have already
expired, a debugging message will be printed in the log and the URB
will be accepted as usual. Assuming it was submitted by a completion
handler (which is normally the case), it will complete shortly
thereafter with all the usb_iso_packet_descriptor status fields marked
-EXDEV.
This fixes (for ehci-hcd)
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1191603
It should be applied to all kernels that include commit 4005ad4390.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Maksim Boyko <maksboyko@yandex.ru>
CC: Clemens Ladisch <clemens@ladisch.de>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wa_urb_enqueue_run locks and unlocks its list lock as it traverses the
list of queued transfers. This was done to prevent deadlocking due to
acquiring locks in reverse order in different places. The problem is that
releasing the lock during the list traversal could allow the dequeue
routine to corrupt the list while it is being iterated over. This patch
moves all list entries to a temp list while holding the list lock, then
traverses the temp list with no lock held.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hub_status_data function on the wireless USB root hub controller
(wusbhc_rh_status_data) always returns a positive value even if no ports
have changed. This patch updates wusbhc_rh_status_data to only return a
positive value if the root hub status needs to be queried. The current
implementation can also leave the upper bits of the port bitmap
uninitialized if wusbhc->ports_max is not one less than an even multiple
of 8. This patch fixes that as well by initializing the buffer to 0.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB Embedded High-speed Host Electrical Test (EHSET) defines the
SINGLE_STEP_SET_FEATURE test as follows:
1) The host enumerates the test device with VID:0x1A0A, PID:0x0108
2) The host sends the SETUP stage of a GetDescriptor(Device)
3) The device ACKs the request
4) The host issues SOFs for 15 seconds allowing the test operator to
raise the scope trigger just above the SOF voltage level
5) The host sends the IN packet
6) The device sends data in response, triggering the scope
7) The host sends an ACK in response to the data
This patch adds additional handling to the EHCI hub driver and allows
the EHSET driver to initiate this test mode by issuing a a SetFeature
request to the root hub with a Test Selector value of 0x06. From there
it mimics ehci_urb_enqueue() but separately submits QTDs for the
SETUP and DATA/STATUS stages in order to insert a delay in between.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
[jackp@codeaurora.org: imported from commit c2084930 on codeaurora.org;
minor cleanup and updated author email]
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If someone provided meaningful error codes from reset() we should tell the
user what they were.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While reading the config parsing code I noticed this check is missing, without
this check config->desc.wTotalLength can end up with a value larger then the
dev->rawdescriptors length for the config, and when userspace then tries to
get the rawdescriptors bad things may happen.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor so that register writes for configuration are only performed if
the device has a regmap provided and also register as a platform driver.
This allows the driver to be used to manage GPIO based control of the
device.
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: devicetree@vger.kernel.org
Reviewed-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are no software visible differences that I am aware of but in case
any are discovered allow the DTS to specify exactly which device is
present.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since there is no runtime interface for changing modes this is probably
the most sensible default.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for supporting operation without an I2C control interface
factor out the I2C-specific parts of the probe routine from those that
don't do any register I/O.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will give access to the diagnostic infrastructure regmap has but
the main point is to support future refactoring.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the connect signal is pulled high then the device will start up meaning
that if we just pull it high on probe then the device will start running
prior to the configuration being written out. Fix this by pulling the GPIO
low when we reset and only pulling it high when configuration is finished.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The /RESET GPIO is not manipulated from atomic context so support GPIOs
that can't be written from atomic context by using _cansleep().
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_USB_SUPPORT is not selected we get things like:
scripts/kconfig/mconf Kconfig
warning: (MIPS_SEAD3 && PMC_MSP && CPU_CAVIUM_OCTEON) selects USB_EHCI_BIG_ENDIAN_MMIO which has unmet direct dependencies (USB_SUPPORT && USB)
It is much cleaner to make the various system Kconfigs select
USB_EHCI_BIG_ENDIAN_MMIO rather than move the system config
information into USB's Kconfig, but the warnings are annoying.
Eliminate the warning by moving the definition of
USB_EHCI_BIG_ENDIAN_MMIO outside of all the Kconfig if statements.
While we are at it move USB_OHCI_BIG_ENDIAN_DESC,
USB_OHCI_BIG_ENDIAN_MMIO, USB_OHCI_LITTLE_ENDIAN and
USB_EHCI_BIG_ENDIAN_DESC too, as they could very well suffer similar
problems for other systems.
Get rid of the redundant "default n" in USB_OHCI_BIG_ENDIAN_DESC and
USB_OHCI_BIG_ENDIAN_MMIO
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The intn and connect GPIO properties are swapped in the code which will
cause failures at runtime if these are connected, fix the code.
There are currently no in-tree users of this device to check or update.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of having to create a new driver for a "simple" usb to serial
device, mush them all into one file, with a macro, so as to make it easy
to add new ones.
Cc: "René Bürgel" <rene.buergel@sohard.de>
Acked-by: Wei Shuai <cpuwolf@gmail.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Acked-by: Frans Klaver <frans.klaver@xsens.com>
Cc: "Wesley W. Terpstra" <w.terpstra@gsi.de>
Cc: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch marks all xHCI controllers as no_sg_constraint
since xHCI supports building packet from discontinuous buffers.
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some host controllers(such as xHCI) can support building
packet from discontinuous buffers, so introduce one flag
and helper for this kind of host controllers, then the
feature can help some applications(such as usbnet) by
supporting arbitrary length of sg buffers.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All 4 transfer types can work well on EHCI HCD after switching to run
URB giveback in tasklet context, so mark all HCD drivers to support
it.
Also we don't need to release ehci->lock during URB giveback any more.
>From below test results on 3 machines(2 ARM and one x86), time
consumed by EHCI interrupt handler droped much without performance
loss.
1 test description
1.1 mass storage performance test:
- run below command 10 times and compute the average performance
dd if=/dev/sdN iflag=direct of=/dev/null bs=200M count=1
- two usb mass storage device:
A: sandisk extreme USB 3.0 16G(used in test case 1 & case 2)
B: kingston DataTraveler G2 4GB(only used in test case 2)
1.2 uvc function test:
- run one simple capture program in the below link
http://kernel.ubuntu.com/~ming/up/capture.c
- capture format 640*480 and results in High Bandwidth mode on the
uvc device: Z-Star 0x0ac8/0x3450
- on T410(x86) laptop, also use guvcview to watch video capture/playback
1.3 about test2 and test4
- both two devices involved are tested concurrently by above test items
1.4 how to compute irq time(the time consumed by ehci_irq)
- use trace points of irq:irq_handler_entry and irq:irq_handler_exit
1.5 kernel
3.10.0-rc3-next-20130528
1.6 test machines
Pandaboard A1: ARM CortexA9 dural core
Arndale board: ARM CortexA15 dural core
T410: i5 CPU 2.67GHz quad core
2 test result
2.1 test case1: single mass storage device performance test
--------------------------------------------------------------------
upstream | patched
perf(MB/s)+irq time(us) | perf(MB/s)+irq time(us)
--------------------------------------------------------------------
Pandaboard A1: 25.280(avg:145,max:772) | 25.540(avg:14, max:75)
Arndale board: 29.700(avg:33, max:129) | 29.700(avg:10, max:50)
T410: 34.430(avg:17, max:154*)| 34.660(avg:12, max:155)
---------------------------------------------------------------------
2.2 test case2: two mass storage devices' performance test
--------------------------------------------------------------------
upstream | patched
perf(MB/s)+irq time(us) | perf(MB/s)+irq time(us)
--------------------------------------------------------------------
Pandaboard A1: 15.840/15.580(avg:158,max:1216) | 16.500/16.160(avg:15,max:139)
Arndale board: 17.370/16.220(avg:33 max:234) | 17.480/16.200(avg:11, max:91)
T410: 21.180/19.820(avg:18 max:160) | 21.220/19.880(avg:11, max:149)
---------------------------------------------------------------------
2.3 test case3: one uvc streaming test
- uvc device works well(on x86, luvcview can be used too and has
same result with uvc capture)
--------------------------------------------------------------------
upstream | patched
irq time(us) | irq time(us)
--------------------------------------------------------------------
Pandaboard A1: (avg:445, max:873) | (avg:33, max:44)
Arndale board: (avg:316, max:630) | (avg:20, max:27)
T410: (avg:39, max:107) | (avg:10, max:65)
---------------------------------------------------------------------
2.4 test case4: one uvc streaming plus one mass storage device test
--------------------------------------------------------------------
upstream | patched
perf(MB/s)+irq time(us) | perf(MB/s)+irq time(us)
--------------------------------------------------------------------
Pandaboard A1: 20.340(avg:259,max:1704)| 20.390(avg:24, max:101)
Arndale board: 23.460(avg:124,max:726) | 23.370(avg:15, max:52)
T410: 28.520(avg:27, max:169) | 28.630(avg:13, max:160)
---------------------------------------------------------------------
2.5 test case5: read single mass storage device with small transfer
- run below command 10 times and compute the average speed
dd if=/dev/sdN iflag=direct of=/dev/null bs=4K count=4000
1), test device A:
--------------------------------------------------------------------
upstream | patched
perf(MB/s)+irq time(us) | perf(MB/s)+irq time(us)
--------------------------------------------------------------------
Pandaboard A1: 6.5(avg:21, max:64) | 6.5(avg:10, max:24)
Arndale board: 8.13(avg:12, max:23) | 8.06(avg:7, max:17)
T410: 6.66(avg:13, max:131) | 6.84(avg:11, max:149)
---------------------------------------------------------------------
2), test device B:
--------------------------------------------------------------------
upstream | patched
perf(MB/s)+irq time(us) | perf(MB/s)+irq time(us)
--------------------------------------------------------------------
Pandaboard A1: 5.5(avg:21,max:43) | 5.49(avg:10, max:24)
Arndale board: 5.9(avg:12, max:22) | 5.9(avg:7, max:17)
T410: 5.48(avg:13, max:155) | 5.48(avg:7, max:140)
---------------------------------------------------------------------
* On T410, sometimes read ehci status register in ehci_irq takes more
than 100us, and the problem has been reported on the link:
http://marc.info/?t=137065867300001&r=1&w=2
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ehci-hcd currently unlinks an interrupt QH when it becomes empty, that
is, after its last URB completes. This works well because in almost
all cases, the completion handler for an interrupt URB resubmits the
URB; therefore the QH doesn't become empty and doesn't get unlinked.
When we start using tasklets for URB completion, this scheme won't work
as well. The resubmission won't occur until the tasklet runs, which
will be some time after the completion is queued with the tasklet.
During that delay, the QH will be empty and so will be unlinked
unnecessarily.
To prevent this problem, this patch adds a 5-ms time delay before empty
interrupt QHs are unlinked. Most often, during that time the interrupt
URB will be resubmitted and thus we can avoid unlinking the QH.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch does the below improvement:
- think QH_STATE_COMPLETING as unlinking state since all URBs on the
endpoint should be in unlinking or unlinked when doing endpoint_disable()
- add "WARN_ON(!list_empty(&qh->qtd_list));" if qh->qh_state is
QH_STATE_LINKED because there shouldn't be any active transfer in qh
- when qh->qh_state is QH_STATE_LINKED, the QH(async or periodic)
should be in its corresponding list, so the search through the async
list isn't necessary.
- unlink periodic QH to speed up unlinking if the QH is in linked
state
Basically, only the last one is related with this patchset because
the assumption of "periodic qh self-unlinks on empty" isn't true
any more when we introduce unlink-wait for periodic qh.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch implements the mechanism of giveback of URB in
tasklet context, so that hardware interrupt handling time for
usb host controller can be saved much, and HCD interrupt handling
can be simplified.
Motivations:
1), on some arch(such as ARM), DMA mapping/unmapping is a bit
time-consuming, for example: when accessing usb mass storage
via EHCI on pandaboard, the common length of transfer buffer is 120KB,
the time consumed on DMA unmapping may reach hundreds of microseconds;
even on A15 based box, the time is still about scores of microseconds
2), on some arch, reading DMA coherent memoery is very time-consuming,
the most common example is usb video class driver[1]
3), driver's complete() callback may do much things which is driver
specific, so the time is consumed unnecessarily in hardware irq context.
4), running driver's complete() callback in hardware irq context causes
that host controller driver has to release its lock in interrupt handler,
so reacquiring the lock after return may busy wait a while and increase
interrupt handling time. More seriously, releasing the HCD lock makes
HCD becoming quite complicated to deal with introduced races.
So the patch proposes to run giveback of URB in tasklet context, then
time consumed in HCD irq handling doesn't depend on drivers' complete and
DMA mapping/unmapping any more, also we can simplify HCD since the HCD
lock isn't needed to be released during irq handling.
The patch should be reasonable and doable:
1), for drivers, they don't care if the complete() is called in hard irq
context or softirq context
2), the biggest change is the situation in which usb_submit_urb() is called
in complete() callback, so the introduced tasklet schedule delay might be a
con, but it shouldn't be a big deal:
- control/bulk asynchronous transfer isn't sensitive to schedule
delay
- the patch schedules giveback of periodic URBs using
tasklet_hi_schedule, so the introduced delay should be very
small
- for ISOC transfer, generally, drivers submit several URBs
concurrently to avoid interrupt delay, so it is OK with the
little schedule delay.
- for interrupt transfer, generally, drivers only submit one URB
at the same time, but interrupt transfer is often used in event
report, polling, ... situations, and a little delay should be OK.
Considered that HCDs may optimize on submitting URB in complete(), the
patch may cause the optimization not working, so introduces one flag to mark
if the HCD supports to run giveback URB in tasklet context. When all HCDs
are ready, the flag can be removed.
[1], http://marc.info/?t=136438111600010&r=1&w=2
Cc: Oliver Neukum <oliver@neukum.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Tegra30 EHCI controller is mostly compatible with the Tegra20
controller, except Tegra30 includes the HOSTPC register extension.
The has_hostpc capability bit must be set in the ehci_hcd structure if
the controller has such extensions. The new tegra_ehci_soc_config
structure is added to describe the differences between the SoCs.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The Tegra30 TRM recommends configuration of certain PHY parameters for
optimal quality. Program the following registers based on device tree
parameters:
- UTMIP_XCVR_HSSLEW: HS slew rate control.
- UTMIP_HSSQUELCH_LEVEL: HS squelch detector level
- UTMIP_HSDISCON_LEVEL: HS disconnect detector level.
These registers exist in Tegra20, but programming them hasn't been
necessary, so these parameters won't be set on Tegra20 to keep the
device trees backward compatible.
Additionally, the UTMIP_XCVR_SETUP parameter can be set from fuses
instead of a software-programmed value, as the optimal value can
vary between invidual boards. The boolean property
nvidia,xcvr-setup-use-fuses can be used to enable this behaviour.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The Tegra30 USB PHY is a bit different than the Tegra20 PHY:
- The EHCI controller supports the HOSTPC register extension, and some
of the fields that the PHY needs to modify (PHCD and PTS) have moved
to the new HOSTPC register.
- Some of the UTMI PLL configuration registers have moved from the USB
register space to the Clock-And-Reset controller space. In Tegra30
the clock driver is responsible for configuring the UTMI PLL.
- The USBMODE register must be explicitly written to enter host mode.
- Certain PHY parameters need to be programmed for optimal signal
quality. Support for this will be added in the next patch.
The new tegra_phy_soc_config structure is added to describe the
differences between the SoCs.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some of the PHY parameters are not set according to the TRMs:
- UTMIP_FS_PREABMLE_J should be set, not cleared
- UTMIP_XCVR_LSBIAS_SEL should be cleared, not set
- UTMIP_PD_CHRG should be set in host mode and cleared in device mode
- UTMIP_XCVR_SETUP is a two-part field; the upper bits were not set
properly
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The has_hostpc capability bit indicates that the host controller has the
HOSTPC register extensions, but at the same time enables clock disabling
power saving features with the PHY Low Power Clock Disable (PHCD) bit.
However, some host controllers have the HOSTPC extensions but don't
support the low-power feature, so the PHCD bit must not be set on those
controllers. Add a separate capability bit for the low-power feature
instead, and change all existing users of has_hostpc to use this new
capability bit.
The idea for this commit is taken from an old 2012 commit that never got
merged ("disociate chipidea PHY low power suspend control from hostpc")
Inspired-by: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The conversion to videobuf2 failed to check the return value of
vb2_qbuf(). Fix it.
Cc: stable@vger.kernel.org
Reported-by: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This driver is currently used by musb' cppi41 couter part. I may merge
both dma engine user of musb at some point but not just yet.
The driver seems to work in RX/TX mode in host mode, tested on mass
storage. I increaed the size of the TX / RX transfers and waited for the
core code to cancel a transfers and it seems to recover.
v2..3:
- use mall transfers on RX side and check data toggle.
- use rndis mode on tx side so we haveon interrupt for 4096 transfers.
- remove custom "transferred" hack and use dmaengine_tx_status() to
compute the total amount of data that has been transferred.
- cancel transfers and reclaim descriptors
v1..v2:
- RX path added
- dma mode 0 & 1 is working
- device tree nodes re-created.
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <djbw@fb.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This moves the two instances from the big node into two child nodes. The
glue layer ontop does almost nothing.
There is one devices containing the control module for USB (2) phy,
(2) usb and later the dma engine. The usb device is the "glue device"
which contains the musb device as a child. This is what we do ever since.
The new file musb_am335x is just here to prob the new bus and populate
child devices.
There are a lot of changes to the dsps file as a result of the changes:
- musb_core_offset
This is gone. The device tree provides memory ressources information
for the device there is no need to "fix" things
- instances
This is gone as well. If we have two instances then we have have two
child enabled nodes in the device tree. For instance the SoC in beagle
bone has two USB instances but only one has been wired up so there is
no need to load and init the second instance since it won't be used.
- dsps_glue is now per glue device
In the past there was one of this structs but with an array of two and
each instance accessed its variable depending on the platform device
id.
- no unneeded copy of structs
I do not know why struct dsps_musb_wrapper is copied but it is not
necessary. The same goes for musb_hdrc_platform_data which allocated
on demand and then again by platform_device_add_data(). One copy is
enough.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dsps uses a nop driver which is added in dsps itself and does the PHY
on/off calls within dsps. Since those calls are now moved the nop driver
itself, we can now request the phy proper phy and remove those calls.
Currently only the first musb interface is used so we only add one phy
node for now.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This driver is a redo of my earlier attempt. It uses parts of the
generic PHY driver and uses the new control driver for the register
the phy needs to power on/off the phy. It also enables easy access for
the wakeup register which is not yet implemented.
The difference between the omap attempt is:
- no static holding variable
- one global visible function which exports a struct with callbacks to
access the "control" registers.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch exports the mostly generic functions so they can be used from
other phy driver instead of duplicating the code.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The "nop" driver isn't a do-nothing-stub but supports a couple functions
like clock on/off or is able to use a voltage regulator. This patch
simply renames the driver to "generic" since it is easy possible to
extend it by a simple function istead of writing a complete driver.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When platform_driver_probe() is not used, bind/unbind via sysfs
is enabled. Thus, __exit_p annotation should be removed from
remove().
Also, mv_otg_remove() is staticized, because this function is
used only in this file. Fix the following sparse warning:
drivers/usb/phy/phy-mv-usb.c:656:5: warning: symbol 'mv_otg_remove' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
mv_u3d_phy_shutdown() is used only in this file.
Fix the following sparse warning:
drivers/usb/phy/phy-mv-u3d-usb.c:85:6: warning: symbol 'mv_u3d_phy_shutdown' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
control_selector_init() is used only in this file.
audio_bind_config() is used only in audio.c file to which
f_uac1.c is included. Thus, these functions are staticized
to fix the following warnings.
drivers/usb/gadget/f_uac1.c:698:12: warning: symbol 'control_selector_init' was not declared. Should it be static?
drivers/usb/gadget/f_uac1.c:722:12: warning: symbol 'audio_bind_config' was not declared. Should it be static?
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
rndis_init() and rndis_exit() are used only in this file.
Fix the following sparse warnings:
drivers/usb/gadget/rndis.c:1145:5: warning: symbol 'rndis_init' was not declared. Should it be static?
drivers/usb/gadget/rndis.c:1179:6: warning: symbol 'rndis_exit' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The local variables such as 'filename', 'vendor_name', and
'product_name' are pointers; thus, use NULL instead of 0 to fix
the following sparse warnings
drivers/usb/gadget/f_mass_storage.c:3046:27: warning: Using plain integer as NULL pointer
drivers/usb/gadget/f_mass_storage.c:3050:28: warning: Using plain integer as NULL pointer
drivers/usb/gadget/f_mass_storage.c:3051:29: warning: Using plain integer as NULL pointer
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As far as prep_dma() is called with spinlock held,
we have to pass GFP_ATOMIC regardless of gfp argument.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Modified dwc3-omap to receive connect and disconnect notification using
extcon framework. Also did the necessary cleanups required after
adapting to extcon framework.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
When building the htmldocs (in verbose mode), scripts/kernel-doc reports the
following type of warnings:
Warning(drivers/usb/core/usb.c:76): No description found for return value of
'usb_find_alt_setting'
Fix them by:
- adding some missing descriptions of return values
- using "Return" sections for those descriptions
Signed-off-by: Yacine Belkadi <yacine.belkadi.1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AT91 PMC (Power Management Controller) provides an USB clock used by
USB Full Speed host (ohci) and USB Full Speed device (udc).
The usb drivers (ohci and udc) must configure this clock to 48Mhz.
This configuration was formely done in mach-at91/clock.c, but this
implementation will be removed when moving to common clk framework.
This patch adds support for usb clock retrieval and configuration, and is
backward compatible with the current at91 clk implementation (if usb clk
is not found, it does not configure/enable it).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds missing clk_put on fclk and iclk in case the probe function
fails after these clocks have been retrieved.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
fusb300_rdcxf() used only in this file.
Fix the following sparse warning:
drivers/usb/gadget/fusb300_udc.c:560:6: warning: symbol 'fusb300_rdcxf' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
'req' is a pointer; thus, use NULL instead of 0
to fix the following sparse warning:
drivers/usb/gadget/goku_udc.c:775:13: warning: Using plain integer as NULL pointer
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SET_SYSTEM_SLEEP_PM_OPS are only used
when the CONFIG_PM_SLEEP is enabled. Unnecessary CONFIG_PM ifdefs
are removed.
drivers/usb/dwc3/dwc3-pci.c:215:12: warning: 'dwc3_pci_suspend' defined but not used [-Wunused-function]
drivers/usb/dwc3/dwc3-pci.c:224:12: warning: 'dwc3_pci_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The AT91 PMC (Power Management Controller) provides an USB clock used by
USB Full Speed host (ohci) and USB Full Speed device (udc).
The usb drivers (ohci and udc) must configure this clock to 48Mhz.
This configuration was formely done in mach-at91/clock.c, but this
implementation will be removed when moving to common clk framework.
This patch adds support for usb clock retrieval and configuration, and is
backward compatible with the current at91 clk implementation (if usb clk
is not found, it does not configure/enable it).
Changes since v1:
- use IS_ENABLED(CONFIG_COMMON_CLK) to isolate new at91 clk support
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In theory, an EHCI controller can turn off the PORT_RESUME or
PORT_RESET bits in a port status register all by itself (and some
controllers actually do this). We shouldn't depend on these bits
being set correctly.
This patch rearranges the code in ehci-hcd that handles completion of
port resets and resumes. We guarantee that ehci->reset_done[portnum]
is nonzero if a reset or resume is in progress, and that the portnum
bit is set in ehci->resuming_ports if the operation is a resume. (To
help enforce this guarantee, the patch prevents suspended ports from
being reset.) Therefore it's not necessary to look at the port status
bits to learn what's going on.
The patch looks bigger than it really is, because it changes the
indentation level of a sizeable region of code. Most of what it
actually does is interchange some tests. The only functional changes
are testing reset_done and resuming_ports rather than PORT_RESUME and
PORT_RESET, removing a now-unnecessary check for spontaneous
resets of the PORT_RESUME and PORT_RESET bits, and preventing a
suspended or resuming port from being reset.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ehci-hcd driver isn't as careful as it should be about the way it
uses ehci->resuming_ports. One of the omissions was fixed recently by
commit 47a64a13d5 (USB: EHCI: Fix resume signalling on remote
wakeup), but there are other places that need attention:
When a port's suspend feature is explicitly cleared, the
corresponding bit in resuming_ports should be set and the core
should be notified about the port resume.
We don't need to clear a resuming_ports bit when a reset
completes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's not clear if the type_0 and type_1 chips support the divisor based baud
rate encoding method, so don't use it until anyone with such chip has tested it
to avoid regressions with the following patches.
Even if it has been working fine with these chips since the code has been added
2 years ago, this change will not cause any regressions, because the baud rates
currently supported/allowed with the divisor based method are supported with
the direct method, too.
The code for the divisor based method also isn't entirely correct (yet), so that the
direct encoding method actually works better (sets the baud rate more precisely).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hub driver's usb_port_suspend() routine doesn't handle errors
related to Link Power Management properly. It always returns failure,
it doesn't try to clean up the wakeup setting, (in the case of system
sleep) it doesn't try to go ahead with the port suspend regardless,
and it doesn't try to apply the new power-off mechanism.
This patch fixes these problems.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hub driver is inconsistent in its organization of code for
enabling and disabling remote wakeup. There is a special routine to
disable wakeup for SuperSpeed devices but not for slower devices, and
there is no special routine to enable wakeup.
This patch refactors the code. It renames and changes the existing
function to make it handle both SuperSpeed and non-SuperSpeed devices,
and it adds a corresponding routine to enable remote wakeup. It also
changes the speed determination to look at the device's speed rather
than the speed of the parent hub -- this shouldn't make any difference
because a SuperSpeed device always has to be attached to a SuperSpeed
hub and conversely.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch simplifies the interface presented by usb_get_status().
Instead of forcing callers to check for the proper data length and
convert the status value to host byte order, the function will now
do these things itself.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB hub driver's event handler contains a check to catch SuperSpeed
devices that transitioned into the SS.Inactive state and tries to fix
them with a reset. It decides whether to do a plain hub port reset or
call the usb_reset_device() function based on whether there was a device
attached to the port.
However, there are device/hub combinations (found with a JetFlash
Transcend mass storage stick (8564:1000) on the root hub of an Intel
LynxPoint PCH) which can transition to the SS.Inactive state on
disconnect (and stay there long enough for the host to notice). In this
case, above-mentioned reset check will call usb_reset_device() on the
stale device data structure. The kernel will send pointless LPM control
messages to the no longer connected device address and can even cause
several 5 second khubd stalls on some (buggy?) host controllers, before
finally accepting the device's fate amongst a flurry of error messages.
This patch makes the choice of reset dependent on the port status that
has just been read from the hub in addition to the existence of an
in-kernel data structure for the device, and only proceeds with the more
extensive reset if both are valid.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A randconfig build hit the following build errors because xhci.c and
xhci-mem.c use dma mapping functions but don't include
<linux/dma-mapping.h>. Add the missing includes to fix the build errors.
drivers/usb/host/xhci.c In function 'xhci_gen_setup':
drivers/usb/host/xhci.c +4872 : error: implicit declaration of function 'dma_set_mask'
drivers/usb/host/xhci.c +4872 : error: implicit declaration of function 'DMA_BIT_MASK'
drivers/usb/host/xhci-mem.c In function 'xhci_free_stream_ctx':
drivers/usb/host/xhci-mem.c +435 : error: implicit declaration of function 'dma_free_coherent'
drivers/usb/host/xhci-mem.c In function 'xhci_alloc_stream_ctx':
drivers/usb/host/xhci-mem.c +463 : error: implicit declaration of function 'dma_alloc_coherent'
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The USB hub driver's event handler contains a check to catch SuperSpeed
devices that transitioned into the SS.Inactive state and tries to fix
them with a reset. It decides whether to do a plain hub port reset or
call the usb_reset_device() function based on whether there was a device
attached to the port.
However, there are device/hub combinations (found with a JetFlash
Transcend mass storage stick (8564:1000) on the root hub of an Intel
LynxPoint PCH) which can transition to the SS.Inactive state on
disconnect (and stay there long enough for the host to notice). In this
case, above-mentioned reset check will call usb_reset_device() on the
stale device data structure. The kernel will send pointless LPM control
messages to the no longer connected device address and can even cause
several 5 second khubd stalls on some (buggy?) host controllers, before
finally accepting the device's fate amongst a flurry of error messages.
This patch makes the choice of reset dependent on the port status that
has just been read from the hub in addition to the existence of an
in-kernel data structure for the device, and only proceeds with the more
extensive reset if both are valid.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Use the wrapper function for retrieving the
platform_data instead of accessing dev->platform_data
directly.
While at that also make change 'node' initialization
to use the dev pointer.
Inspired-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This code doesn't serve any purpose anymore, since the aio retry
infrastructure has been removed.
This change should be safe because aio_read/write are also used for
synchronous IO, and called from do_sync_read()/do_sync_write() - and
there's no looping done in the sync case (the read and write syscalls).
Signed-off-by: Kent Overstreet <koverstreet@google.com>
Cc: Zach Brown <zab@redhat.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Asai Thambi S P <asamymuthupa@micron.com>
Cc: Selvan Mani <smani@micron.com>
Cc: Sam Bradshaw <sbradshaw@micron.com>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Originally, io_event() was documented to return the io_event if
cancellation succeeded - the io_event wouldn't be delivered via the ring
buffer like it normally would.
But this isn't what the implementation was actually doing; the only
driver implementing cancellation, the usb gadget code, never returned an
io_event in its cancel function. And aio_complete() was recently changed
to no longer suppress event delivery if the kiocb had been cancelled.
This gets rid of the unused io_event argument to kiocb_cancel() and
kiocb->ki_cancel(), and changes io_cancel() to return -EINPROGRESS if
kiocb->ki_cancel() returned success.
Also tweak the refcounting in kiocb_cancel() to make more sense.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
Cc: Zach Brown <zab@redhat.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Asai Thambi S P <asamymuthupa@micron.com>
Cc: Selvan Mani <smani@micron.com>
Cc: Sam Bradshaw <sbradshaw@micron.com>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
RT Systems makes many usb serial cables based on the ftdi_sio driver for
programming various amateur radios. This patch is a full listing of
their current product offerings and should allow these cables to all
be recognized.
Signed-off-by: Rick Farina (Zero_Chaos) <zerochaos@gentoo.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FOTG210 is an OTG controller which can be configured as an
USB2.0 host. FOTG210 host is an ehci-like controller with
some differences. First, register layout of FOTG210 is
incompatible with EHCI. Furthermore, FOTG210 is lack of
siTDs which means iTDs are used for both HS and FS ISO
transfer.
Signed-off-by: Feng-Hsin Chiang <john453@faraday-tech.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following regression that has been introduced recently with
commit b2d6d98fc7:
With type_0 and type_1 chips
- all baud rates < 1228800 baud are rounded up to 1228800 baud
- the device silently runs at 9600 baud for all baud rates > 1228800
baud
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using below configs, the compile will have error:
ERROR: "ehci_init_driver" undefined!
.config:
CONFIG_USB_CHIPIDEA=m
CONFIG_USB_CHIPIDEA_HOST=y
CONFIG_USB_CHIPIDEA_DEBUG=y
The reason is chipidea host uses symbol from ehci, but ehci
is not compiled. Let the chipidea host depend on
ehci even it is built as module.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following build warnings on x86:
drivers/usb/chipidea/core.c: In function 'hw_phymode_configure':
drivers/usb/chipidea/core.c:226:3: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/usb/chipidea/core.c:230:3: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/usb/chipidea/core.c:243:3: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/usb/chipidea/core.c:246:3: warning: large integer implicitly truncated to unsigned type [-Woverflow]
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some fixes for v3.11-rc3. Mostly related to
the recent conversion to configfs done on the gadget
drivers, but we also have a fix for MUSB resources
on platforms which need 3 resources instead of 2, and
a fix for the sysfs_notify() call on udc-core.c which
was notifying an unexistent file.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=WNXc
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.11-rc3
Here are some fixes for v3.11-rc3. Mostly related to
the recent conversion to configfs done on the gadget
drivers, but we also have a fix for MUSB resources
on platforms which need 3 resources instead of 2, and
a fix for the sysfs_notify() call on udc-core.c which
was notifying an unexistent file.
When deferred probe happens driver will try to ioremap multiple times
and will fail. Memory resource.start variable is a global variable,
modifications in this field will be accumulated on every probe.
Fix this by moving the above operations after driver hold all
required PHY's.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use switch() instead of if-else when checking for the PHY type.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The name of udc state attribute file under sysfs is registered as
"state", while usb_gadget_set_state take it as "status" when it's
going to update. This patch fixes the typo.
Signed-off-by: Rong Wang <Rong.Wang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Cc: <stable@kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The compatibility layer which the USBF_PHONET_INCLUDED was a part of
is no longer present - the USBF_PHONET_INCLUDED is not #defined by anyone
anymore, so the ifndef is always true. Removing it.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Introduced by commit 59835a (usb: gadget: multi: use
function framework for ACM.)
Make rndis_do_config() consistent with cdc_do_config() in the way it
handles returning the PTR_ERR(f_acm_*).
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The EOI register is not present in the AM335x memory space according to
the TRM and thus removed.
Should any platform using the EOI register get merged then it may be
used again if the register address is not zero.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The ti81xx platform is not fully supported right now. This patch renames
the date structure to a am33xx prefix which is actually used.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the new of_usb_get_dr_mode helper function for parsing dr_mode
from the device tree. Also replace the usage of the custom
tegra_usb_phy_mode enum with the standard enum.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the new of_usb_get_phy_mode helper function for parsing phy_type
from the device tree.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The Tegra EHCI driver is no longer using these custom functions, so they
can be removed.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use devm_get_phy_by_phandle to get a PHY device instead of the custom
Tegra functions.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Register the Tegra PHY device instances with the PHY subsystem so that
the Tegra EHCI driver can locate a PHY via the standard APIs.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Platform data is not used in tegra-ehci anymore, so remove all
references to it.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ehci-tegra calls devm_usb_get_phy, which will never succeed since the Tegra
PHY does not register itself with the PHY subsystem. It is also completely
redundant since the code has already located a PHY via an internal API.
Call otg_set_host unconditionally to simplify the code since it should
be safe to do so.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
struct usb_phy already has a field for the device pointer, so this
unnecessary field can be removed.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The tegra ehci driver has enabled USB vbus regulators directly using
GPIOs and the device tree attribute nvidia,vbus-gpio. This is ugly
and causes error messages on boot when both the regulator driver
and the ehci driver want access to the same GPIO.
After this patch, usb vbus regulators for tegra usb phy devices are specified
with the device tree attribute vbus-supply = <&x> where x is a regulator defined
in the device tree. The old nvidia,vbus-gpio property is no longer supported.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
UTMIP parameters used to be hardcoded into tables in the
PHY driver. This patch reads them from the device tree instead
in accordance with the phy-tegra-usb DT documentation.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit 8d2421e ("usb: musb: kill global and static for multi instance")
removed the global dma_mask copy and replaced by parent's DMA mask. The
problem here is that if the parent does not have a dma_mask then
musb_remove() goes kaboom.
Instead trying to fix this I was thinking we do we need to erase
dma_mask in the first place?
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ti81xx does not have a baseport mainline i.e. it should not boot. The
amount of rework that is required makes it easier to simply remove that
platform (i.e. that possible platform device) and add it later once it
comes back with DT support.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If the init / shutdown function of the phy moves out of dsps into the
phy driver, then dsps needs to call the callbacks of the phy driver to
ensure that this happens.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace clk_enable/disable with clk_prepare_enable/disable_unprepare to
avoid common clk framework warnings.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Current usbhsx_for_each_xxx macro will read out-of-array's
memory after last loop operation.
It was not good C language operation, and the binary which was
compiled by (at least) gcc 4.8.1 is broken
This patch tidyup these issues
Reported-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Reviewed-by: Takashi Yoshii <takashi.yoshii.zj@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use a mapping table (dpll_map) to match the possible system clock rates
to the appropriate DPLL parameters.
Introduce a function "omap_usb3_get_dpll_params()" that will
return the matching DPLL parameters for the given clock rate.
Also, bail out on phy init if DPLL locking fails.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ehci-omap needs NOP_USB_XCEIV PHY driver to function
properly, so select it. As the USB PHY drivers no longer
depend on USB_PHY, it is safe to select the PHY drivers.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Adrien Vergé <adrienverge@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert PHY Drivers from menuconfig to menu so that the PHY drivers
can be explicitely selected by the controller drivers.
USB_PHY is no longer a user visible option. It is upto to the PHY
drivers to select it if needed. This patch does so for the existing
PHY drivers that use the USB_PHY library.
Doing so moves the USB_PHY and PHY driver selection problem from the
end user to the PHY and controller driver developer.
e.g.
Earlier, a controller driver (e.g. EHCI_OMAP) that needs to select
a PHY driver (e.g. NOP_PHY) couldn't do so because the PHY driver
depended on USB_PHY. Making the controller driver depend on USB_PHY
has a negative effect i.e. it becomes invisible to the user till
USB_PHY is enabled. Most end users will not familiar with this.
With this patch, the end user just needs to select the controller driver
needed for his/her platform without worrying about which PHY driver to
select.
Also update USB_EHCI_MSM, USB_LPC32XX and USB_OMAP to not depend
on USB_PHY any more. They can safely select the necessary PHY drivers.
[ balbi@ti.com : refreshed on top of my next branch. Changed bool
followed by default n into def_bool n ]
CC: Pavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
before changing to configured state, we need
to wait until gadget driver has had a chance
to process the request.
In case of USB_GADGET_DELAYED_STATUS, that means
we need to defer usb_gadget_set_state() until
the upcoming usb_ep_queue().
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case we're switching back to USB_STATE_ADDRESS
from USB_STATE_CONFIGURED (if host sends
a set configuration command for configuration
zero), we should only switch if the request
is successfully processed by the gadget driver.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
usb_gadget_set_state() will call sysfs_notify()
which might sleep. Some users might want to call
usb_gadget_set_state() from the very IRQ handler
which actually changes the gadget state.
Instead of having every UDC driver add their own
workqueue for such a simple notification, we're
adding it generically to our struct usb_gadget,
so the details are hidden from all UDC drivers.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
that function isn't really processing any event
buffer, rather just checking whether it contains
events to be processed.
Due to that reason, we're reaning it to dwc3_check_event_buf()
instead.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We can make use of bit 31 of the GEVNTSIZ(n)
registers to mask/unmask interrupts from that
particular interrupter.
With that feature, we can easily drop IRQF_ONESHOT
from our driver which makes it possible to
properly change IRQ priorities when using RT
patchset *and* it allows us to make use of the
scheduler to choose the proper time to handle
this IRQ thread.
Signed-off-by: Felipe Balbi <balbi@ti.com>
That register has more than just the event buffer
size; we can also mask and unmask that particular
interrupter on bit 31 of that register.
In this patch we introduce the necessary macros
and make sure to use the new macros while also
making sure we mask interrupts during driver
removal.
Signed-off-by: Felipe Balbi <balbi@ti.com>
the macro DWC3_DCFG_LPM_CAP was defined twice.
This patch just removes one of the definitions,
no functional changes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
that way we get debugging information when
enabling verbose debug of the driver.
It will be no-op otherwise.
Signed-off-by: Felipe Balbi <balbi@ti.com>
by moving that dev_vdbg() to the internal
__dwc3_gadget_ep_enable() we get the print
even when enable ep0, which calls the internal
function directly.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Recent versions of the core, can suspend and resume
the PHYs automatically, so we don't need to fiddle
with dwc3's Global PHY registers at all.
On versions prior to 1.94a this patch will mean
that we will never ask dwc3 to suspend the PHY.
This is an acceptable behavior or such old versions
of the core, specially considering that the only
chip known to have a version prior to 1.94a was
OMAP5 ES1.0 and that's not supported in mainline
kernel, because it was just a test spin of OMAP5.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adapts the dwc3 to use the device tree helper
"of_usb_get_dr_mode" for the mode of operation of the dwc3 instance
being probed.
[ balbi@ti.com : make of_usb_get_dr_mode() conditional on
dev->of_node and let pdata pass dr_mode too ]
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
stmp_reset_block() may fail, so let's check its return value and propagate it
in the case of error.
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The musb driver no longer uses procfs, so get rid of the proc_dir_entry
variable in struct musb.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds OF match table to the driver to allow instantiating it
using device tree.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
all other drivers using Synopsys IPs with DT
have a compatible of snps,$driver, in order
to add consistency, we are switching over to
snps,dwc3 but keeping synopsys,dwc3 in the core
driver to maintain backwards compatibility.
New DTS bindings should NOT use synopsys,dwc3.
Signed-off-by: Felipe Balbi <balbi@ti.com>
in order to allow different instances of the
core work in different maximum speeds, we will
move the maximum_speed module_parameter to
both DeviceTree (making use the new maximum-speed
DT property) and platform_data.
Signed-off-by: Felipe Balbi <balbi@ti.com>
in case we're not in a DT boot, we should
still be able to tell the driver how to behave.
In order to be able to pass flags to the driver,
we introduce platform_data structure which the
core driver should use.
Signed-off-by: Felipe Balbi <balbi@ti.com>
this helper will be used for controllers which
want to work at a lower speed even though they
support higher USB transfer rates.
One such case is Texas Instruments' AM437x
SoC where it uses a USB3 controller without
a USB3 PHY, rendering the controller USB2-only.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is a Linux-only driver which makes use
of GPL-only symbols. It makes no sense to
maintain Dual BSD/GPL licensing for this driver.
Considering that the amount of work to use this
driver in any different operating system would likely
be as large as developing the driver from scratch and
considering that we depend on GPL-only symbols, we
will switch over to a GPL v2-only license.
Cc: Anton Tikhomirov <av.tikhomirov@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
@list is not as a parameter of dwc3_event_buffer, so remove it in
comments.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We cannot request an IRQ with spinlocks held
as that would trigger a sleeping inside
spinlock warning.
Cc: <stable@vger.kernel.org> # v3.10
Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
That driver hasn't been really maintained for
a long time. It doesn't compile in any way, it
includes non-existent headers, has no users,
and is just plain broken.
The person who used to work with that driver
has publicly stated that he has no plans to
touch that driver again and is ok with removal[1].
Due to these factors, imx_udc is now removed from
the tree, if someone really believe it needs to
be kept, please fix the bugs in that driver.
[1] http://marc.info/?l=linux-usb&m=136197620417636&w=2
Signed-off-by: Felipe Balbi <balbi@ti.com>
Glue layers are starting to have separate
requirements. For example, OMAP's glue layer
is starting to use extcon framework which
no one else needs.
In order to make it clear the proper dependencies,
we are now allowing glue layers to be selectable
so that each glue layer can list their own dependencies
without messing with the core IP driver.
Signed-off-by: Felipe Balbi <balbi@ti.com>
If the descriptor is missing the reqeust is never unmapped. This patch
changes this and renames the cleanup label to unlock since there is no
cleanup done. The cleanup would revert the allocation of ressource (i.e.
this dma mapping) but it does not, it simply unlocks and returns.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The cleanup in the error is missing the dma controller. The structure is
allocated at runtime and ux500 allocates even a little more than just
this struct. So cleanup!
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes is_dma_capable() and an ifdef in the init/exit path
around init/de-init of the dma_controller. Since we have the empty stubs
in the PIO code we can call it without gcc trouble. Earlier we had an
ifdef and the is_dma_capable() macro where gcc ignored the if (0) path
even that the function was not around :)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add a dma_controller_create() returning NULL so a few ifdefs can
dropped.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The core code creates a controller and immediately after that it calls
the ->start() callback. This one might drop an error but nobody cares.
The same thing happens in the destroy corner: First ->stop() called
followed by destroy callback. So why not merge those two into the same
function since there is no difference.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This check is hardly required and alas is wrong. 'c' might be NULL but
the chances are low that 'controller' after the container_of() becomes
NULL.
Since no other DMA implementation is doing that and musb-core does not
call it with a NULL pointer it can dropped.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The ifdef reads somehow better than an ifndef
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Silence compiler warnings on 64-bit systems introduced by commit
05cf0dec ("USB: mos7840: fix race in led handling") which uses the
usb-serial data pointer to temporarily store the device type during
probe but failed to add the required casts.
[gregkh - change uintptr_t to unsigned long]
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix race in LED handling introduced by commit 0eafe4de ("USB: serial:
mos7840: add support for MCS7810 devices") which reused the port control
urb for manipulating the LED without making sure that the urb is not
already in use. This could lead to the control urb being manipulated
while in flight.
Fix by adding a dedicated LED urb and ctrlrequest along with a LED-busy
flag to handle concurrency.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix race in device-type detection introduced by commit 0eafe4de ("USB:
serial: mos7840: add support for MCS7810 devices") which used a static
variable to hold the device type.
Move type detection to probe and use serial data to store the device
type.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix race in mos7840_get_reg which unconditionally manipulated the
control urb (which may already be in use) by adding a control-urb busy
flag.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds a driver for the Suunto ANT+ USB device, exposing it as a usb
serial device. This lets the userspace "gant" program to talk to the
device to communicate over the ANT+ protocol to any devices it finds.
Reported-by: Steinar Gunderson <sgunderson@bigfoot.com>
Tested-by: Steinar Gunderson <sgunderson@bigfoot.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When ohci-hcd is shutting down, call ohci_usb_reset reset ohci-hcd, the
root hub generate an interrupt, but ohci->rh_state is OHCI_RH_HALTED,
and ohci_irq ignore the interrupt, the kernel trigger warning "irq
nobody cared". ehci-hcd is first disable interrupts, then reset ehci.
This patch disable ohci interrupt before reset ohci.
The patch is tested at the arm cortex-a9 demo board.
Signed-off-by: caizhiyong <caizhiyong@huawei.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57f6ce072e ("usb: phy:
add a new driver for usb3 phy") added the new Kconfig option
OMAP_USB3, but it had no dependencies whatsoever, and hence
became available across all arch/platforms.
Which presumably caused this to show up in x86 randconfig:
warning: (USB_MUSB_HDRC && OMAP_USB3) selects \
OMAP_CONTROL_USB which has unmet direct \
dependencies (USB_SUPPORT && ARCH_OMAP2PLUS)
Then commit 6992819feb ("usb: phy:
fix Kconfig warning") was added. However, this just deleted the
ARCH_OMAP2PLUS dependency from OMAP_CONTROL_USB, further
compounding the problem by opening up OMAP_CONTROL_USB to
all arch/platforms as well.
Earlier it was suggested[1] that we revert the change of 6992819feb
to restore the dependency, and add a same ARCH_OMAP2PLUS dependency
to the new OMAP_USB3 entry. However that was discouraged on the
grounds of people wanting the extra sanity compile testing on x86,
even though the driver could probably never be used there.
Now we have CONFIG_COMPILE_TEST, so developers who value the ability
to compile drivers on an architecture that it never can be used for
can have that, and people who want dependencies to shield them from
seeing options that aren't relevant to their platform get what they
want too.
Here we restore the dependency but couple it with COMPILE_TEST, in
order to achieve both of the above goals.
[1] https://patchwork.kernel.org/patch/2194511/
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Moiz Sonasath <m-sonasath@ti.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge the usb_hcd_ep93xx_probe() into ohci_hcd_ep93xx_drv_probe() and
the usb_hcd_ep93xx_remove() into ohci_hcd_ep93xx_drv_remove(). As Alan
Stern pointed out, there is no reason for them to be separate.
Also, as Alan Stern suggested, eliminate the ep93xx_start_hc() and
ep93xx_stop_hc() routines and simply call clk_enable() and clk_disable()
directly. The extra level of redirection does not add any clarity.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_clk_get() to make the code a bit cleaner and simpler.
This also fixes a bug where a clk_put() is not done if usb_add_hcd()
fails.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_ioremap_resource() to make the code a bit cleaner and
simpler.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Updated skel_read() in usb-skeleton.c. When there is no data in the
buffer, we would allow retry for both blocking and nonblocking cases.
Original logic give retry only for blocking case. Actually we can also
allow retry for nonblocking case. This will reuse the existing retry
logic and handle the return of -EAGAIN in one place. Also if the data to
be read is short and can be retrieved in quick time, we can also give a
chance for nonblocking case and may catch the data and copy it back to
userspace in one read() call too.
Signed-off-by: Chen Wang <unicornxx.wang@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kfree(data) will be called implicitly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a few cases where braces are not needed. This patch removes
unnecessary '& 255' pieces as well when lvalue type is u8.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recent patch series introduces few trailing spaces. This patch removes them.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For certain (HP) printers the printer device_id does not only contain a
static part identifying the printer, but it also contains a dynamic part
giving printer status, ink level, etc.
To get to this info various userspace utilities need to be able to make a
printer class 'get_device_id' request without first claiming the interface
(as that is in use for the actual printer driver).
Since the printer class 'get_device_id' request does not change interface
settings in anyway, allowing this without claiming the interface should not
cause any issues.
CC: Sanjay Kumar <sanjay.kumar14@hp.com>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most HCD drivers are doing the same thing in their ".shutdown" callback
so it makes sense to use the generic usb_hcd_platform_shutdown()
handler there.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes a redundant nested "#ifdef CONFIG_PM" from the hub
driver. It also adds a label to the "#endif" line corresponding to
the outer "#ifdef CONFIG_PM".
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An Embedded Host High-Speed Electrical Test (EHSET) test fixture is
used to initiate test modes on a host controller in order to perform
the high speed electrical testing procedure for USB-IF compliance.
When this test fixture is connected to a host, it can enumerate as
one of several selectable VID/PID pairs, each corresponding to one
of the following test modes:
* TEST_SE0_NAK
* TEST_J
* TEST_K
* TEST_PACKET
* HS_HOST_PORT_SUSPEND_RESUME
* SINGLE_STEP_GET_DEV_DESC
* SINGLE_STEP_SET_FEATURE
The USB EHSET procedure can be found here:
http://www.usb.org/developers/onthego/EHSET_v1.01.pdf
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
[jackp@codeaurora.org: imported from commit 073c9409 on codeaurora.org;
minor cleanup and updated author email]
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bInterval must be on the range 1 - 16, if we
want to pass the maximum allowed, we should
be passing 16.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bInterval must be on the range 1 - 16, if we
want to pass the maximum allowed, we should
be passing 16
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Frank Schäfer