While $ARCH can be relatively flexible (see Makefile and
tools/scripts/Makefile.arch), $SRCARCH always corresponds to a directory
name under arch/.
Therefore, build samples with -D__TARGET_ARCH_$(SRCARCH), since that
matches the expectations of bpf_helpers.h.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Adds support for fq's Earliest Departure Time to HBM (Host Bandwidth
Manager). Includes a new BPF program supporting EDT, and also updates
corresponding programs.
It will drop packets with an EDT of more than 500us in the future
unless the packet belongs to a flow with less than 2 packets in flight.
This is done so each flow has at least 2 packets in flight, so they
will not starve, and also to help prevent delayed ACK timeouts.
It will also work with ECN enabled traffic, where the packets will be
CE marked if their EDT is more than 50us in the future.
The table below shows some performance numbers. The flows are back to
back RPCS. One server sending to another, either 2 or 4 flows.
One flow is a 10KB RPC, the rest are 1MB RPCs. When there are more
than one flow of a given RPC size, the numbers represent averages.
The rate limit applies to all flows (they are in the same cgroup).
Tests ending with "-edt" ran with the new BPF program supporting EDT.
Tests ending with "-hbt" ran on top HBT qdisc with the specified rate
(i.e. no HBM). The other tests ran with the HBM BPF program included
in the HBM patch-set.
EDT has limited value when using DCTCP, but it helps in many cases when
using Cubic. It usually achieves larger link utilization and lower
99% latencies for the 1MB RPCs.
HBM ends up queueing a lot of packets with its default parameter values,
reducing the goodput of the 10KB RPCs and increasing their latency. Also,
the RTTs seen by the flows are quite large.
Aggr 10K 10K 10K 1MB 1MB 1MB
Limit rate drops RTT rate P90 P99 rate P90 P99
Test rate Flows Mbps % us Mbps us us Mbps ms ms
-------- ---- ----- ---- ----- --- ---- ---- ---- ---- ---- ----
cubic 1G 2 904 0.02 108 257 511 539 647 13.4 24.5
cubic-edt 1G 2 982 0.01 156 239 656 967 743 14.0 17.2
dctcp 1G 2 977 0.00 105 324 408 744 653 14.5 15.9
dctcp-edt 1G 2 981 0.01 142 321 417 811 660 15.7 17.0
cubic-htb 1G 2 919 0.00 1825 40 2822 4140 879 9.7 9.9
cubic 200M 2 155 0.30 220 81 532 655 74 283 450
cubic-edt 200M 2 188 0.02 222 87 1035 1095 101 84 85
dctcp 200M 2 188 0.03 111 77 912 939 111 76 325
dctcp-edt 200M 2 188 0.03 217 74 1416 1738 114 76 79
cubic-htb 200M 2 188 0.00 5015 8 14ms 15ms 180 48 50
cubic 1G 4 952 0.03 110 165 516 546 262 38 154
cubic-edt 1G 4 973 0.01 190 111 1034 1314 287 65 79
dctcp 1G 4 951 0.00 103 180 617 905 257 37 38
dctcp-edt 1G 4 967 0.00 163 151 732 1126 272 43 55
cubic-htb 1G 4 914 0.00 3249 13 7ms 8ms 300 29 34
cubic 5G 4 4236 0.00 134 305 490 624 1310 10 17
cubic-edt 5G 4 4865 0.00 156 306 425 759 1520 10 16
dctcp 5G 4 4936 0.00 128 485 221 409 1484 7 9
dctcp-edt 5G 4 4924 0.00 148 390 392 623 1508 11 26
v1 -> v2: Incorporated Andrii's suggestions
v2 -> v3: Incorporated Yonghong's suggestions
v3 -> v4: Removed credit update that is not needed
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Due to recent change of include path at commit b552d33c80
("samples/bpf: fix include path in Makefile"), some of the
previous include options became unnecessary.
This commit removes duplicated include options in Makefile.
Signed-off-by: Daniel T. Lee <danieltimlee@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Recent commit included libbpf.h in selftests/bpf/bpf_util.h.
Since some samples use bpf_util.h and samples/bpf/Makefile doesn't
have libbpf.h path included, build was failing. Let's add the path
in samples/bpf/Makefile.
Signed-off-by: Prashant Bhole <prashantbhole.linux@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Quentin reports that commit 07c3bbdb1a ("samples: bpf: print
a warning about headers_install") is producing the false
positive when make is invoked locally, from the samples/bpf/
directory.
When make is run locally it hits the "all" target, which
will recursively invoke make through the full build system.
Speed up the "local" run which doesn't actually build anything,
and avoid false positives by skipping all the probes if not in
kbuild environment (cover both the new warning and the BTF
probes).
Reported-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
It seems like periodically someone posts patches to "fix"
header includes. The issue is that samples expect the
include path to have the uAPI headers (from usr/) first,
and then tools/ headers, so that locally installed uAPI
headers take precedence. This means that if users didn't
run headers_install they will see all sort of strange
compilation errors, e.g.:
HOSTCC samples/bpf/test_lru_dist
samples/bpf/test_lru_dist.c:39:8: error: redefinition of ‘struct list_head’
struct list_head {
^~~~~~~~~
In file included from samples/bpf/test_lru_dist.c:9:0:
../tools/include/linux/types.h:69:8: note: originally defined here
struct list_head {
^~~~~~~~~
Try to detect this situation, and print a helpful warning.
v2: just use HOSTCC (Jiong).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Convert test_cgrp2_attach2 example into a proper test_cgroup_attach
kselftest. It's better because we do run kselftest on a constant
basis, so there are better chances to spot a potential regression.
Also make it slightly less verbose to conform kselftests output style.
Output example:
$ ./test_cgroup_attach
#override:PASS
#multi:PASS
test_cgroup_attach:PASS
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Provide a count of class types for a summary of MAD packets. The example
shows one way to filter the trace data based on management class.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The program nrm creates a cgroup and attaches a BPF program to the
cgroup for testing HBM (Host Bandwidth Manager) for egress traffic.
One still needs to create network traffic. This can be done through
netesto, netperf or iperf3.
A follow-up patch contains a script to create traffic.
USAGE: hbm [-d] [-l] [-n <id>] [-r <rate>] [-s] [-t <secs>]
[-w] [-h] [prog]
Where:
-d Print BPF trace debug buffer
-l Also limit flows doing loopback
-n <#> To create cgroup "/hbm#" and attach prog. Default is /nrm1
This is convenient when testing HBM in more than 1 cgroup
-r <rate> Rate limit in Mbps
-s Get HBM stats (marked, dropped, etc.)
-t <time> Exit after specified seconds (deault is 0)
-w Work conserving flag. cgroup can increase its bandwidth
beyond the rate limit specified while there is available
bandwidth. Current implementation assumes there is only
NIC (eth0), but can be extended to support multiple NICs.
Currrently only supported for egress. Note, this is just
a proof of concept.
-h Print this info
prog BPF program file name. Name defaults to hbm_out_kern.o
More information about HBM can be found in the paper "BPF Host Resource
Management" presented at the 2018 Linux Plumbers Conference, Networking Track
(http://vger.kernel.org/lpc_net2018_talks/LPC%20BPF%20Network%20Resource%20Paper.pdf)
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
A cgroup skb BPF program to limit cgroup output bandwidth.
It uses a modified virtual token bucket queue to limit average
egress bandwidth. The implementation uses credits instead of tokens.
Negative credits imply that queueing would have happened (this is
a virtual queue, so no queueing is done by it. However, queueing may
occur at the actual qdisc (which is not used for rate limiting).
This implementation uses 3 thresholds, one to start marking packets and
the other two to drop packets:
CREDIT
- <--------------------------|------------------------> +
| | | 0
| Large pkt |
| drop thresh |
Small pkt drop Mark threshold
thresh
The effect of marking depends on the type of packet:
a) If the packet is ECN enabled, then the packet is ECN ce marked.
The current mark threshold is tuned for DCTCP.
c) Else, it is dropped if it is a large packet.
If the credit is below the drop threshold, the packet is dropped.
Note that dropping a packet through the BPF program does not trigger CWR
(Congestion Window Reduction) in TCP packets. A future patch will add
support for triggering CWR.
This BPF program actually uses 2 drop thresholds, one threshold
for larger packets (>= 120 bytes) and another for smaller packets. This
protects smaller packets such as SYNs, ACKs, etc.
The default bandwidth limit is set at 1Gbps but this can be changed by
a user program through a shared BPF map. In addition, by default this BPF
program does not limit connections using loopback. This behavior can be
overwritten by the user program. There is also an option to calculate
some statistics, such as percent of packets marked or dropped, which
the user program can access.
A latter patch provides such a program (hbm.c)
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Some samples don't really need the magic of bpf_load,
switch them to libbpf.
v2: - specify program types.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
bpftool can do all the things load_sock_ops used to do, and more.
Point users to bpftool instead of maintaining this sample utility.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This commit converts the xdpsock sample application to use the AF_XDP
functions present in libbpf. This cuts down the size of it by nearly
300 lines of code.
The default ring sizes plus the batch size has been increased and the
size of the umem area has decreased. This so that the sample application
will provide higher throughput. Note also that the shared umem code
has been removed from the sample as this is not supported by libbpf
at this point in time.
Tested-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Some of XDP samples that are attaching the bpf program to the interface
via libbpf's bpf_set_link_xdp_fd are still using the bpf_load.c for
loading and manipulating the ebpf program and maps. Convert them to do
this through libbpf usage and remove bpf_load from the picture.
While at it remove what looks like debug leftover in
xdp_redirect_map_user.c
In xdp_redirect_cpu, change the way that the program to be loaded onto
interface is chosen - user now needs to pass the program's section name
instead of the relative number. In case of typo print out the section
names to choose from.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
x86 compilation has required asm goto support since 4.17.
Since clang does not support asm goto, at 4.17,
Commit b1ae32dbab ("x86/cpufeature: Guard asm_volatile_goto usage
for BPF compilation") worked around the issue by permitting an
alternative implementation without asm goto for clang.
At 5.0, more asm goto usages appeared.
[yhs@148 x86]$ egrep -r asm_volatile_goto
include/asm/cpufeature.h: asm_volatile_goto("1: jmp 6f\n"
include/asm/jump_label.h: asm_volatile_goto("1:"
include/asm/jump_label.h: asm_volatile_goto("1:"
include/asm/rmwcc.h: asm_volatile_goto (fullop "; j" #cc " %l[cc_label]" \
include/asm/uaccess.h: asm_volatile_goto("\n" \
include/asm/uaccess.h: asm_volatile_goto("\n" \
[yhs@148 x86]$
Compiling samples/bpf directories, most bpf programs failed
compilation with error messages like:
In file included from /home/yhs/work/bpf-next/samples/bpf/xdp_sample_pkts_kern.c:2:
In file included from /home/yhs/work/bpf-next/include/linux/ptrace.h:6:
In file included from /home/yhs/work/bpf-next/include/linux/sched.h:15:
In file included from /home/yhs/work/bpf-next/include/linux/sem.h:5:
In file included from /home/yhs/work/bpf-next/include/uapi/linux/sem.h:5:
In file included from /home/yhs/work/bpf-next/include/linux/ipc.h:9:
In file included from /home/yhs/work/bpf-next/include/linux/refcount.h:72:
/home/yhs/work/bpf-next/arch/x86/include/asm/refcount.h:70:9: error: 'asm goto' constructs are not supported yet
return GEN_BINARY_SUFFIXED_RMWcc(LOCK_PREFIX "subl",
^
/home/yhs/work/bpf-next/arch/x86/include/asm/rmwcc.h:67:2: note: expanded from macro 'GEN_BINARY_SUFFIXED_RMWcc'
__GEN_RMWcc(op " %[val], %[var]\n\t" suffix, var, cc, \
^
/home/yhs/work/bpf-next/arch/x86/include/asm/rmwcc.h:21:2: note: expanded from macro '__GEN_RMWcc'
asm_volatile_goto (fullop "; j" #cc " %l[cc_label]" \
^
/home/yhs/work/bpf-next/include/linux/compiler_types.h:188:37: note: expanded from macro 'asm_volatile_goto'
#define asm_volatile_goto(x...) asm goto(x)
Most implementation does not even provide an alternative
implementation. And it is also not practical to make changes
for each call site.
This patch workarounded the asm goto issue by redefining the macro like below:
#define asm_volatile_goto(x...) asm volatile("invalid use of asm_volatile_goto")
If asm_volatile_goto is not used by bpf programs, which is typically the case, nothing bad
will happen. If asm_volatile_goto is used by bpf programs, which is incorrect, the compiler
will issue an error since "invalid use of asm_volatile_goto" is not valid assembly codes.
With this patch, all bpf programs under samples/bpf can pass compilation.
Note that bpf programs under tools/testing/selftests/bpf/ compiled fine as
they do not access kernel internal headers.
Fixes: e769742d35 ("Revert "x86/jump-labels: Macrofy inline assembly code to work around GCC inlining bugs"")
Fixes: 18fe58229d ("x86, asm: change the GEN_*_RMWcc() macros to not quote the condition")
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
These explicit rules are unneeded because scripts/Makefile.build
provides a pattern rule to create %.s from %.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add additional checks in tools/testing/selftests/bpf and
samples/bpf such that if clang/llvm compiler can generate
BTF sections, do not use pahole.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Sample program which shows TCP_SAVE_SYN/TCP_SAVED_SYN usage example:
bpf program which is doing TOS/TCLASS reflection (server would reply
with a same TOS/TCLASS as client).
Signed-off-by: Nikita V. Shirokov <tehnerd@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Pull networking updates from David Miller:
"Highlights:
- Gustavo A. R. Silva keeps working on the implicit switch fallthru
changes.
- Support 802.11ax High-Efficiency wireless in cfg80211 et al, From
Luca Coelho.
- Re-enable ASPM in r8169, from Kai-Heng Feng.
- Add virtual XFRM interfaces, which avoids all of the limitations of
existing IPSEC tunnels. From Steffen Klassert.
- Convert GRO over to use a hash table, so that when we have many
flows active we don't traverse a long list during accumluation.
- Many new self tests for routing, TC, tunnels, etc. Too many
contributors to mention them all, but I'm really happy to keep
seeing this stuff.
- Hardware timestamping support for dpaa_eth/fsl-fman from Yangbo Lu.
- Lots of cleanups and fixes in L2TP code from Guillaume Nault.
- Add IPSEC offload support to netdevsim, from Shannon Nelson.
- Add support for slotting with non-uniform distribution to netem
packet scheduler, from Yousuk Seung.
- Add UDP GSO support to mlx5e, from Boris Pismenny.
- Support offloading of Team LAG in NFP, from John Hurley.
- Allow to configure TX queue selection based upon RX queue, from
Amritha Nambiar.
- Support ethtool ring size configuration in aquantia, from Anton
Mikaev.
- Support DSCP and flowlabel per-transport in SCTP, from Xin Long.
- Support list based batching and stack traversal of SKBs, this is
very exciting work. From Edward Cree.
- Busyloop optimizations in vhost_net, from Toshiaki Makita.
- Introduce the ETF qdisc, which allows time based transmissions. IGB
can offload this in hardware. From Vinicius Costa Gomes.
- Add parameter support to devlink, from Moshe Shemesh.
- Several multiplication and division optimizations for BPF JIT in
nfp driver, from Jiong Wang.
- Lots of prepatory work to make more of the packet scheduler layer
lockless, when possible, from Vlad Buslov.
- Add ACK filter and NAT awareness to sch_cake packet scheduler, from
Toke Høiland-Jørgensen.
- Support regions and region snapshots in devlink, from Alex Vesker.
- Allow to attach XDP programs to both HW and SW at the same time on
a given device, with initial support in nfp. From Jakub Kicinski.
- Add TLS RX offload and support in mlx5, from Ilya Lesokhin.
- Use PHYLIB in r8169 driver, from Heiner Kallweit.
- All sorts of changes to support Spectrum 2 in mlxsw driver, from
Ido Schimmel.
- PTP support in mv88e6xxx DSA driver, from Andrew Lunn.
- Make TCP_USER_TIMEOUT socket option more accurate, from Jon
Maxwell.
- Support for templates in packet scheduler classifier, from Jiri
Pirko.
- IPV6 support in RDS, from Ka-Cheong Poon.
- Native tproxy support in nf_tables, from Máté Eckl.
- Maintain IP fragment queue in an rbtree, but optimize properly for
in-order frags. From Peter Oskolkov.
- Improvde handling of ACKs on hole repairs, from Yuchung Cheng"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1996 commits)
bpf: test: fix spelling mistake "REUSEEPORT" -> "REUSEPORT"
hv/netvsc: Fix NULL dereference at single queue mode fallback
net: filter: mark expected switch fall-through
xen-netfront: fix warn message as irq device name has '/'
cxgb4: Add new T5 PCI device ids 0x50af and 0x50b0
net: dsa: mv88e6xxx: missing unlock on error path
rds: fix building with IPV6=m
inet/connection_sock: prefer _THIS_IP_ to current_text_addr
net: dsa: mv88e6xxx: bitwise vs logical bug
net: sock_diag: Fix spectre v1 gadget in __sock_diag_cmd()
ieee802154: hwsim: using right kind of iteration
net: hns3: Add vlan filter setting by ethtool command -K
net: hns3: Set tx ring' tc info when netdev is up
net: hns3: Remove tx ring BD len register in hns3_enet
net: hns3: Fix desc num set to default when setting channel
net: hns3: Fix for phy link issue when using marvell phy driver
net: hns3: Fix for information of phydev lost problem when down/up
net: hns3: Fix for command format parsing error in hclge_is_all_function_id_zero
net: hns3: Add support for serdes loopback selftest
bnxt_en: take coredump_record structure off stack
...
Convert xdpsock_user.c to use libbpf instead of bpf_load.o.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Convert xdp_fwd_user.c to use libbpf instead of bpf_load.o.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
To smoothly test BTF supported binary on samples/bpf,
let samples/bpf/Makefile probe llc, pahole and
llvm-objcopy for BPF support and use them
like tools/testing/selftests/bpf/Makefile
changed from the commit c0fa1b6c3e ("bpf: btf:
Add BTF tests").
Signed-off-by: Taeung Song <treeze.taeung@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
In preparation for enabling command line LDLIBS, re-name HOST_LOADLIBES
to KBUILD_HOSTLDLIBS as the internal use only flags. Also rename
existing usage to HOSTLDLIBS for consistency. This should not have any
visible effects.
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In preparation for enabling command line CFLAGS, re-name HOSTCFLAGS to
KBUILD_HOSTCFLAGS as the internal use only flags. This should not have
any visible effects.
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add an example program showing how to sample packets from XDP using the
perf event buffer. The example userspace program just prints the ethernet
header for every packet sampled.
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2018-05-24
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Björn Töpel cleans up AF_XDP (removes rebind, explicit cache alignment from uapi, etc).
2) David Ahern adds mtu checks to bpf_ipv{4,6}_fib_lookup() helpers.
3) Jesper Dangaard Brouer adds bulking support to ndo_xdp_xmit.
4) Jiong Wang adds support for indirect and arithmetic shifts to NFP
5) Martin KaFai Lau cleans up BTF uapi and makes the btf_header extensible.
6) Mathieu Xhonneux adds an End.BPF action to seg6local with BPF helpers allowing
to edit/grow/shrink a SRH and apply on a packet generic SRv6 actions.
7) Sandipan Das adds support for bpf2bpf function calls in ppc64 JIT.
8) Yonghong Song adds BPF_TASK_FD_QUERY command for introspection of tracing events.
9) other misc fixes from Gustavo A. R. Silva, Sirio Balmelli, John Fastabend, and Magnus Karlsson
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is mostly to test kprobe/uprobe which needs kernel headers.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
S390 bpf_jit.S is removed in net-next and had changes in 'net',
since that code isn't used any more take the removal.
TLS data structures split the TX and RX components in 'net-next',
put the new struct members from the bug fix in 'net' into the RX
part.
The 'net-next' tree had some reworking of how the ERSPAN code works in
the GRE tunneling code, overlapping with a one-line headroom
calculation fix in 'net'.
Overlapping changes in __sock_map_ctx_update_elem(), keep the bits
that read the prog members via READ_ONCE() into local variables
before using them.
Signed-off-by: David S. Miller <davem@davemloft.net>
Building samples with clang ignores the $(Q) setting, always
printing full command to the output. Make it less verbose.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Make complains that it doesn't know how to make libbpf.a:
scripts/Makefile.host:106: target 'samples/bpf/../../tools/lib/bpf/libbpf.a' doesn't match the target pattern
Now that we have it as a dependency of the sources simply add libbpf.a
to libraries not objects.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
There are many ways users may compile samples, some of them got
broken by commit 5f9380572b ("samples: bpf: compile and link
against full libbpf"). Improve path resolution and make libbpf
building a dependency of source files to force its build.
Samples should now again build with any of:
cd samples/bpf; make
make samples/bpf/
make -C samples/bpf
cd samples/bpf; make O=builddir
make samples/bpf/ O=builddir
make -C samples/bpf O=builddir
export KBUILD_OUTPUT=builddir
make samples/bpf/
make -C samples/bpf
Fixes: 5f9380572b ("samples: bpf: compile and link against full libbpf")
Reported-by: Björn Töpel <bjorn.topel@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Now that we can use full powers of libbpf in BPF samples, we
should perhaps make the simplest XDP programs not depend on
bpf_load helpers. This way newcomers will be exposed to the
recommended library from the start.
Use of bpf_prog_load_xattr() will also make it trivial to later
on request offload of the programs by simply adding ifindex to
the xattr.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
There are two copies of event reading loop - in bpftool and
trace_helpers "library". Consolidate them and move the code
to libbpf. Return codes from trace_helpers are kept, but
renamed to include LIBBPF prefix.
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
samples/bpf currently cherry-picks object files from tools/lib/bpf
to link against. Just compile the full library and link statically
against it.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Simple example of fast-path forwarding. It has a serious flaw
in not verifying the egress device index supports XDP forwarding.
If the egress device does not packets are dropped.
Take this only as a simple example of fast-path forwarding.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This is a sample application for AF_XDP sockets. The application
supports three different modes of operation: rxdrop, txonly and l2fwd.
To show-case a simple round-robin load-balancing between a set of
sockets in an xskmap, set the RR_LB compile time define option to 1 in
"xdpsock.h".
v2: The entries variable was calculated twice in {umem,xq}_nb_avail.
Co-authored-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
There is no functionality change in this patch. The common-purpose
trace functions, including perf_event polling and ksym lookup,
are moved from trace_output_user.c and bpf_load.c to
selftests/bpf/trace_helpers.c so that these function can
be reused later in selftests.
Acked-by: Alexei Starovoitov <ast@fb.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Move the testsuite to
selftests/bpf/{test_tunnel_kern.c, test_tunnel.sh}
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
adding bpf's sample program which is using bpf_xdp_adjust_tail helper
by generating ICMPv4 "packet to big" message if ingress packet's size is
bigger then 600 bytes
Signed-off-by: Nikita V. Shirokov <tehnerd@tehnerd.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
add empty raw_tracepoint bpf program to test overhead similar
to kprobe and traditional tracepoint tests
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
CPU is active when have running tasks on it and CPUFreq governor can
select different operating points (OPP) according to different workload;
we use 'pstate' to present CPU state which have running tasks with one
specific OPP. On the other hand, CPU is idle which only idle task on
it, CPUIdle governor can select one specific idle state to power off
hardware logics; we use 'cstate' to present CPU idle state.
Based on trace events 'cpu_idle' and 'cpu_frequency' we can accomplish
the duration statistics for every state. Every time when CPU enters
into or exits from idle states, the trace event 'cpu_idle' is recorded;
trace event 'cpu_frequency' records the event for CPU OPP changing, so
it's easily to know how long time the CPU stays in the specified OPP,
and the CPU must be not in any idle state.
This patch is to utilize the mentioned trace events for pstate and
cstate statistics. To achieve more accurate profiling data, the program
uses below sequence to insure CPU running/idle time aren't missed:
- Before profiling the user space program wakes up all CPUs for once, so
can avoid to missing account time for CPU staying in idle state for
long time; the program forces to set 'scaling_max_freq' to lowest
frequency and then restore 'scaling_max_freq' to highest frequency,
this can ensure the frequency to be set to lowest frequency and later
after start to run workload the frequency can be easily to be changed
to higher frequency;
- User space program reads map data and update statistics for every 5s,
so this is same with other sample bpf programs for avoiding big
overload introduced by bpf program self;
- When send signal to terminate program, the signal handler wakes up
all CPUs, set lowest frequency and restore highest frequency to
'scaling_max_freq'; this is exactly same with the first step so
avoid to missing account CPU pstate and cstate time during last
stage. Finally it reports the latest statistics.
The program has been tested on Hikey board with octa CA53 CPUs, below
is one example for statistics result, the format mainly follows up
Jesper Dangaard Brouer suggestion.
Jesper reminds to 'get printf to pretty print with thousands separators
use %' and setlocale(LC_NUMERIC, "en_US")', tried three different arm64
GCC toolchains (5.4.0 20160609, 6.2.1 20161016, 6.3.0 20170516) but all
of them cannot support printf flag character %' on arm64 platform, so go
back print number without grouping mode.
CPU states statistics:
state(ms) cstate-0 cstate-1 cstate-2 pstate-0 pstate-1 pstate-2 pstate-3 pstate-4
CPU-0 767 6111 111863 561 31 756 853 190
CPU-1 241 10606 107956 484 125 646 990 85
CPU-2 413 19721 98735 636 84 696 757 89
CPU-3 84 11711 79989 17516 909 4811 5773 341
CPU-4 152 19610 98229 444 53 649 708 1283
CPU-5 185 8781 108697 666 91 671 677 1365
CPU-6 157 21964 95825 581 67 566 684 1284
CPU-7 125 15238 102704 398 20 665 786 1197
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Parse netlink ext attribute to get the error message returned by
the card. Code is partially take from libnl.
We add netlink.h to the uapi include of tools. And we need to
avoid include of userspace netlink header to have a successful
build of sample so nlattr.h has a define to avoid
the inclusion. Using a direct define could have been an issue
as NLMSGERR_ATTR_MAX can change in the future.
We also define SOL_NETLINK if not defined to avoid to have to
copy socket.h for a fixed value.
Signed-off-by: Eric Leblond <eric@regit.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Do not build lib/bpf/bpf.o with this Makefile but use the one from the
library directory. This avoid making a buggy bpf.o file (e.g. missing
symbols).
This patch is useful if some code (e.g. Landlock tests) needs both the
bpf.o (from tools/lib/bpf) and the bpf_load.o (from samples/bpf).
Signed-off-by: Mickaël Salaün <mic@digikod.net>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Creating a bpf sample that shows howto use the XDP 'data_meta'
infrastructure, created by Daniel Borkmann. Very few drivers support
this feature, but I wanted a functional sample to begin with, when
working on adding driver support.
XDP data_meta is about creating a communication channel between BPF
programs. This can be XDP tail-progs, but also other SKB based BPF
hooks, like in this case the TC clsact hook. In this sample I show
that XDP can store info named "mark", and TC/clsact chooses to use
this info and store it into the skb->mark.
It is a bit annoying that XDP and TC samples uses different tools/libs
when attaching their BPF hooks. As the XDP and TC programs need to
cooperate and agree on a struct-layout, it is best/easiest if the two
programs can be contained within the same BPF restricted-C file.
As the bpf-loader, I choose to not use bpf_load.c (or libbpf), but
instead wrote a bash shell scripted named xdp2skb_meta.sh, which
demonstrate howto use the iproute cmdline tools 'tc' and 'ip' for
loading BPF programs. To make it easy for first time users, the shell
script have command line parsing, and support --verbose and --dry-run
mode, if you just want to see/learn the tc+ip command syntax:
# ./xdp2skb_meta.sh --dev ixgbe2 --dry-run
# Dry-run mode: enable VERBOSE and don't call TC+IP
tc qdisc del dev ixgbe2 clsact
tc qdisc add dev ixgbe2 clsact
tc filter add dev ixgbe2 ingress prio 1 handle 1 bpf da obj ./xdp2skb_meta_kern.o sec tc_mark
# Flush XDP on device: ixgbe2
ip link set dev ixgbe2 xdp off
ip link set dev ixgbe2 xdp obj ./xdp2skb_meta_kern.o sec xdp_mark
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This sample program can be used for monitoring and reporting how many
packets per sec (pps) are received per NIC RX queue index and which
CPU processed the packet. In itself it is a useful tool for quickly
identifying RSS imbalance issues, see below.
The default XDP action is XDP_PASS in-order to provide a monitor
mode. For benchmarking purposes it is possible to specify other XDP
actions on the cmdline --action.
Output below shows an imbalance RSS case where most RXQ's deliver to
CPU-0 while CPU-2 only get packets from a single RXQ. Looking at
things from a CPU level the two CPUs are processing approx the same
amount, BUT looking at the rx_queue_index levels it is clear that
RXQ-2 receive much better service, than other RXQs which all share CPU-0.
Running XDP on dev:i40e1 (ifindex:3) action:XDP_PASS
XDP stats CPU pps issue-pps
XDP-RX CPU 0 900,473 0
XDP-RX CPU 2 906,921 0
XDP-RX CPU total 1,807,395
RXQ stats RXQ:CPU pps issue-pps
rx_queue_index 0:0 180,098 0
rx_queue_index 0:sum 180,098
rx_queue_index 1:0 180,098 0
rx_queue_index 1:sum 180,098
rx_queue_index 2:2 906,921 0
rx_queue_index 2:sum 906,921
rx_queue_index 3:0 180,098 0
rx_queue_index 3:sum 180,098
rx_queue_index 4:0 180,082 0
rx_queue_index 4:sum 180,082
rx_queue_index 5:0 180,093 0
rx_queue_index 5:sum 180,093
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This adds a basic test for bpf_override_return to verify it works. We
override the main function for mounting a btrfs fs so it'll return
-ENOMEM and then make sure that trying to mount a btrfs fs will fail.
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Ilya Leoshkevich