A display resolution is only supported if it meets all the restrictions
below for Maximum Pipe Pixel Rate.
The display resolution must fit within the maximum pixel rate output
from the pipe. Make sure that the display pipe is able to feed pixels at
a rate required to support the desired resolution.
For each enabled plane on the pipe {
If plane scaling enabled {
Horizontal down scale amount = Maximum[1, plane horizontal size /
scaler horizontal window size]
Vertical down scale amount = Maximum[1, plane vertical size /
scaler vertical window size]
Plane down scale amount = Horizontal down scale amount *
Vertical down scale amount
Plane Ratio = 1 / Plane down scale amount
}
Else {
Plane Ratio = 1
}
If plane source pixel format is 64 bits per pixel {
Plane Ratio = Plane Ratio * 8/9
}
}
Pipe Ratio = Minimum Plane Ratio of all enabled planes on the pipe
If pipe scaling is enabled {
Horizontal down scale amount = Maximum[1, pipe horizontal source size /
scaler horizontal window size]
Vertical down scale amount = Maximum[1, pipe vertical source size /
scaler vertical window size]
Note: The progressive fetch - interlace display mode is equivalent to a
2.0 vertical down scale
Pipe down scale amount = Horizontal down scale amount *
Vertical down scale amount
Pipe Ratio = Pipe Ratio / Pipe down scale amount
}
Pipe maximum pixel rate = CDCLK frequency * Pipe Ratio
In this patch our calculation is based on pipe downscale amount
(plane max downscale amount * pipe downscale amount) instead of Pipe
Ratio. So,
max supported crtc clock with given scaling = CDCLK / pipe downscale.
Flip will fail if,
current crtc clock > max supported crct clock with given scaling.
Changes since V1:
- separate out fixed_16_16 wrapper API definition
Changes since V2:
- Fix buggy crtc !active condition (Maarten)
- use intel_wm_plane_visible wrapper as per Maarten's suggestion
Changes since V3:
- Change failure return from ERANGE to EINVAL
Changes since V4:
- Rebase based on previous patch changes
Changes since V5:
- return EINVAL instead of continue (Maarten)
Changes since V6:
- Improve commit message
- Address review comment
Changes since V7:
- use !enable instead of !active
- rename config variable for consistency (Maarten)
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170526151546.25025-4-mahesh1.kumar@intel.com
SDVO was the last connector that's still using the legacy paths
for properties, and this is with a reason!
This connector implements a lot of properties dynamically,
and some of them shared with the digital connector state,
so sdvo_connector_state subclasses intel_digital_connector_state.
set_property had a lot of validation, but this is handled in the
drm core, so most of the validation can die off. The properties
are written right before enabling the connector, since there is no
good way to update the properties without crtc.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-13-maarten.lankhorst@linux.intel.com
intel_hdmi supports 3 properties, force_audio, broadcast rgb and
scaling mode. The last one is only created for eDP, so the is_eDP
in set_property is not required.
panel fitting and broadcast rgb are straightforward and only requires
changing compute_config.
force_audio is also used to force DVI mode, which means changes to
compute_config and mode_valid. mode_valid is called with
connection_mutex held, so it can safely dereference connector->state.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-11-maarten.lankhorst@linux.intel.com
intel_dp supports 3 properties, scaling mode, broadcast rgb and
force_audio. intel_digital_connector handles the plumbing,
so we only have to hook this up in compute_config and init.
Changes since v1:
- Remove limited_color_range too, unused. (danvet)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-10-maarten.lankhorst@linux.intel.com
Some atomic properties are common between the various kinds of
connectors, for example a lot of them use panel fitting mode.
It makes sense to put a lot of it in a common place, so each
connector can use it while they're being converted.
Implement the properties required for the connectors:
- scaling mode property
- force audio property
- broadcast rgb
- aspect ratio
While at it, make clear that intel_digital_connector_atomic_get_property
is a hack that has to be removed when all connector properties
are converted to atomic.
Changes since v1:
- Scaling mode and aspect ratio are partly handled in core now.
Changes since v2:
- Split out the scaling mode / aspect ratio changes to a preparation
patch.
- Use mode_changed for panel fitter, changes to this property
are checked by fastset.
- Allowed_scaling_modes is removed, handled through core now.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-6-maarten.lankhorst@linux.intel.com
The first step in converting connector properties to atomic is
wiring up the atomic state. We're still not completely supoprting
the scaling mode in the atomic case, but this is the first step
towards it.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-4-maarten.lankhorst@linux.intel.com
More stuff for 4.13:
- skl+ wm fixes from Mahesh Kumar
- some refactor and tests for i915_sw_fence (Chris)
- tune execlist/scheduler code (Chris)
- g4x,g33 gpu reset improvements (Chris, Mika)
- guc code cleanup (Michal Wajdeczko, Michał Winiarski)
- dp aux backlight improvements (Puthikorn Voravootivat)
- buffer based guc/host communication (Michal Wajdeczko)
* tag 'drm-intel-next-2017-05-29' of git://anongit.freedesktop.org/git/drm-intel: (253 commits)
drm/i915: Update DRIVER_DATE to 20170529
drm/i915: Keep the forcewake timer alive for 1ms past the most recent use
drm/i915/guc: capture GuC logs if FW fails to load
drm/i915/guc: Introduce buffer based cmd transport
drm/i915/guc: Disable send function on fini
drm: Add definition for eDP backlight frequency
drm/i915: Drop AUX backlight enable check for backlight control
drm/i915: Consolidate #ifdef CONFIG_INTEL_IOMMU
drm/i915: Only GGTT vma may be pinned and prevent shrinking
drm/i915: Serialize GTT/Aperture accesses on BXT
drm/i915: Convert i915_gem_object_ops->flags values to use BIT()
drm/i915/selftests: Silence compiler warning in igt_ctx_exec
drm/i915/guc: Skip port assign on first iteration of GuC dequeue
drm/i915: Remove misleading comment in request_alloc
drm/i915/g33: Improve reset reliability
Revert "drm/i915: Restore lost "Initialized i915" welcome message"
drm/i915/huc: Update GLK HuC version
drm/i915: Check for allocation failure
drm/i915/guc: Remove action status and statistics from debugfs
drm/i915/g4x: Improve gpu reset reliability
...
Switch to using the common DP helpers instead of using our own.
v2: also remove leftover struct intel_dp_desc (Daniel)
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Move cursor_base, cursor_cntl, and cursor_size from intel_crtc
into intel_plane so that we don't need the crtc for cursor stuff
so much.
Also entirely nuke cursor_addr which IMO doesn't provide any benefit
since it's not actually used by the cursor code itself. I'm not 100%
sure what the SKL+ DDB is code is after by looking at cursor_addr so
I just make it do its checks unconditionally. If that's not correct
then we should likely replace it with somehting like
plane_state->visible.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170327185546.2977-5-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Implement proper two stage watermark programming for g4x. As with
other pre-SKL platforms, the watermark registers aren't double
buffered on g4x. Hence we must sequence the watermark update
carefully around plane updates.
The code is quite heavily modelled on the VLV/CHV code, with some
fairly significant differences due to the different hardware
architecture:
* g4x doesn't use inverted watermark values
* CxSR actually affects the watermarks since it controls memory self
refresh in addition to the max FIFO mode
* A further HPLL SR mode is possible with higher memory wakeup
latency
* g4x has FBC2 and so it also has FBC watermarks
* max FIFO mode for primary plane only (cursor is allowed, sprite is not)
* g4x has no manual FIFO repartitioning
* some TLB miss related workarounds are needed for the watermarks
Actually the hardware is quite similar to ILK+ in many ways. The
most visible differences are in the actual watermakr register
layout. ILK revamped that part quite heavily whereas g4x is still
using the layout inherited from earlier platforms.
Note that we didn't previously enable the HPLL SR on g4x. So in order
to not introduce too many functional changes in this patch I've not
actually enabled it here either, even though the code is now fully
ready for it. We'll enable it separately later on.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170421181432.15216-13-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
This is only used in i915, which had used its own non-atomic way to
deal with the picture aspect ratio. Move selected aspect_ratio to
atomic state and use the atomic state in the affected i915 connectors.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-2-maarten.lankhorst@linux.intel.com
[mlankhorst: taomic -> atomic thanks to Manasi's input]
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the BUILD_BUG_ONs for busy-wait duration outside the
_wait_for_atomic macro as discussed on the mailing list.
v2: Simplify the macro by omitting the ret__ local. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Suggested-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Fixes: 1d1a9774e4 ("drm/i915: Extend intel_wait_for_register_fw() with fast timeout")
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170418105211.7089-1-tvrtko.ursulin@linux.intel.com
If link training at a link rate optimal for a particular
mode fails during modeset's atomic commit phase, then we
let the modeset complete and then retry. We save the link rate
value at which link training failed, update the link status property
to "BAD" and use a lower link rate to prune the modes. It will redo
the modeset on the current mode at lower link rate or if the current
mode gets pruned due to lower link constraints then, it will send a
hotplug uevent for userspace to handle it.
This is also required to pass DP CTS tests 4.3.1.3, 4.3.1.4,
4.3.1.6.
This patch is a resend of the original commit id (233ce881dd
"drm/i915: Implement Link Rate fallback on Link training failure")
which got reverted in this commit id (afc1ebf456 Revert
"drm/i915: Implement Link Rate fallback on Link training failure")
due to CI failures.
After investigating the CI failures it was found that these
were essentially the failures which were always there but hidden because
they used to be DRM_DEBUG_KMS messages for link failures so never got
caught by CI. But now this patch actually throws DRM_ERROR if the link
training fails at RBR and 1 lane. So it caught these link train failures.
There were two failures:
1. On SKL 6700k this was because the machine in CI lab is a SKL desktop
without eDP on Port A. But our VBT initialization code in the driver writes
VBT defaults in a way that it always sets DP flag on Port A and this does
not get cleared after parsing the VBT outputs. This has been fixed in
commit id (bb1d132935 "drm/i915/vbt: split out defaults that are set
when there is no VBT) and (665788572c "drm/i915/vbt: don't propagate
errors from intel_bios_init())
2. On ILK-650 desktop - This was happening because of a bad monitor desktop
combination. I switched the monitor in the CI lab and that helped get rid
of the link failures on ILK system.
v10:
* Rebase on drm-tip and resend after revert
v9:
* Use the trimmed max values of link rate/lane count based on
link train fallback (Daniel Vetter)
v8:
* Set link_status to BAD first and then call mode_valid (Jani Nikula)
v7:
Remove the redundant variable in previous patch itself
v6:
* Obtain link rate index from fallback_link_rate using
the helper intel_dp_link_rate_index (Jani Nikula)
* Include fallback within intel_dp_start_link_train (Jani Nikula)
v5:
* Move set link status to drm core (Daniel Vetter, Jani Nikula)
v4:
* Add fallback support for non DDI platforms too
* Set connector->link status inside set_link_status function
(Jani Nikula)
v3:
* Set link status property to BAd unconditionally (Jani Nikula)
* Dont use two separate variables link_train_failed and link_status
to indicate same thing (Jani Nikula)
v2:
* Squashed a few patches (Jani Nikula)
Acked-by: Tony Cheng <tony.cheng@amd.com>
Acked-by: Harry Wentland <Harry.wentland@amd.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/16ca48b1e74c618929245e9a085b9e3483c3a16d.1491485983.git.jani.nikula@intel.com
Those properties are not hooked up on MST and were ignored. Best not expose them at all.
Without this the next patch fails to start on X.org, because the DP-MST properties could
not be read.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/751b85a0-81cd-09e2-9e60-6d4ddbf1c6ac@linux.intel.com
Testcase: kms_properties
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Maarten needs both the new connector->atomic_check hook and the
connection_mutex locking changes in the probe helpers to be able to
start merging the connector property conversion to atomic.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The source might not support as many lanes as the sink, or the link
training might have failed at higher lane counts. Take these into
account.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/cf59530acafaf9258fb643d321ad251b44f34e29.1491485983.git.jani.nikula@intel.com
If we modify these on the fly depending on the link conditions, don't
pretend they are sink properties.
Some link vs. sink confusion still remains, but we'll take care of them
in follow-up patches.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/3739b4fac502ebd1c6e075a62c1a195e4094eb16.1491485983.git.jani.nikula@intel.com
Now that source rates are static and sink rates are updated whenever
DPCD is updated, we can do and cache the intersection of them whenever
sink rates are updated. This reduces code complexity, as we don't have
to keep calling the functions to intersect. We also get rid of several
common rates arrays on stack.
Limiting the common rates by a max link rate can be done by picking the
first N elements of the cached common rates.
v2: get rid of the local common_rates variable (Manasi)
v3: don't clobber cached eDP rates on short pulse (Ville)
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/e3b287e8cb6559b1f8fd4e80b78a8d22f1802eb7.1491485983.git.jani.nikula@intel.com
Looking at DPCD DP_MAX_LINK_RATE may be completely bogus for eDP 1.4
which is allowed to use link rate select method and have 0 in max link
rate. With this change, it makes sense to store the max rate as the
actual rate rather than as a bw code.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/3e8baadb406d59f414cab36fed9f0b35d207fde5.1491485983.git.jani.nikula@intel.com
Last drm-misc-next pull req for 4.12
Core changes:
- fb_helper checkpatch cleanup and simplified _add_one_connector() (Thierry)
- drm_ioctl and drm_sysfs improved/gained documentation (Daniel)
- [ABI] Repurpose reserved field in drm_event_vblank for crtc_id (Ander)
- Plumb acquire ctx through legacy paths to avoid lock_all and legacy_backoff
(Daniel)
- Add connector_atomic_check to check conn constraints on modeset (Maarten)
- Add drm_of_find_panel_or_bridge to remove boilerplate in drivers (Rob)
Driver changes:
- meson moved to drm-misc (Neil)
- Added support for Amlogic GX SoCs in dw-hdmi (Neil)
- Rockchip unbind actually cleans up the things bind initializes (Jeffy)
- A couple misc fixes in virtio, dw-hdmi
NOTE: this also includes a backmerge of drm-next as well rc5 (we needed vmwgfx
as well as the new synopsys media formats)
* tag 'drm-misc-next-2017-04-07' of git://anongit.freedesktop.org/git/drm-misc: (77 commits)
Revert "drm: Don't allow interruptions when opening debugfs/crc"
drm: Only take cursor locks when the cursor plane exists
drm/vmwgfx: Fix fbdev emulation using legacy functions
drm/rockchip: Shutdown all crtcs when unbinding drm
drm/rockchip: Reorder drm bind/unbind sequence
drm/rockchip: analogix_dp: Disable clock when unbinding
drm/rockchip: vop: Unprepare clocks when unbinding
drm/rockchip: vop: Enable pm domain before vop_initial
drm/rockchip: cdn-dp: Don't unregister audio dev when unbinding
drm/rockchip: cdn-dp: Don't try to release firmware when not loaded
drm: bridge: analogix: Destroy connector & encoder when unbinding
drm: bridge: analogix: Disable clock when unbinding
drm: bridge: analogix: Unregister dp aux when unbinding
drm: bridge: analogix: Detach panel when unbinding analogix dp
drm: Don't allow interruptions when opening debugfs/crc
drm/virtio: don't leak bo on drm_gem_object_init failure
drm: bridge: dw-hdmi: fix input format/encoding from plat_data
drm: omap: use common OF graph helpers
drm: convert drivers to use drm_of_find_panel_or_bridge
drm: convert drivers to use of_graph_get_remote_node
...
mode_valid() called from drm_helper_probe_single_connector_modes()
may need to look at connector->state because what a valid mode is may
depend on connector properties being set. For example some HDMI modes
might be rejected when a connector property forces the connector
into DVI mode.
Some implementations of detect() already lock all state,
so we have to pass an acquire_ctx to them to prevent a deadlock.
This means changing the function signature of detect() slightly,
and passing the acquire_ctx for locking multiple crtc's.
For the callbacks, it will always be non-zero. To allow callers
not to worry about this, drm_helper_probe_detect_ctx is added
which might handle -EDEADLK for you.
Changes since v1:
- Always set ctx parameter.
Changes since v2:
- Always take connection_mutex when probing.
Changes since v3:
- Remove the ctx from intel_dp_long_pulse, and add
WARN_ON(!connection_mutex) (danvet)
- Update docs to clarify the locking situation. (danvet)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1491504920-4017-1-git-send-email-maarten.lankhorst@linux.intel.com
There is some conflation related to sink rates, making this change more
complicated than it would otherwise have to be. There are three changes
here that are rather difficult to split up:
1) Use the intel_dp->sink_rates array for all DP, not just eDP 1.4. We
initialize it from DPCD on eDP 1.4 like before, but generate it based
on DP_MAX_LINK_RATE on others. This reduces code complexity when we
need to use the sink rates; they are all always in the sink_rates
array.
2) Update the sink rate array whenever we read DPCD, and use the
information from there. This increases code readability when we need
the sink rates.
3) Disentangle fallback rate limiting from sink rates. In the code, the
max rate is a dynamic property of the *link*, not of the *sink*. Do
the limiting after intersecting the source and sink rates, which are
static properties of the devices.
This paves the way for follow-up refactoring that I've refrained from
doing here to keep this change as simple as it possibly can.
v2: introduce use_rate_select and handle non-confirming eDP (Ville)
v3: don't clobber cached eDP rates on short pulse (Ville)
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/071bad76467f8ab2e73f3f61ad52d5a468004c71.1490712890.git.jani.nikula@intel.com
We need the source rates array so often that it makes sense to set it
once at init. This reduces function calls when we need the rates, making
the code easier to follow.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/aa998882d2b824f671272c60e9d26621ab9d2d17.1490712890.git.jani.nikula@intel.com
Geminilake platform sports a native HDMI 2.0 controller, and is
capable of driving pixel-clocks upto 594Mhz. HDMI 2.0 spec
mendates scrambling for these higher clocks, for reduced RF footprint.
This patch checks if the monitor supports scrambling, and if required,
enables it during the modeset.
V2: Addressed review comments from Ville:
- Do not track scrambling status in DRM layer, track somewhere in
driver like in intel_crtc_state.
- Don't talk to monitor at such a low layer, set monitor scrambling
in intel_enable_ddi() before enabling the port.
V3: Addressed review comments from Jani
- In comments, function names, use "sink" instead of "monitor",
so that the implementation could be close to the language of
HDMI spec.
V4: Addressed review comment from Maarten
- scrambling -> hdmi_scrambling
- high_tmds_clock_ratio -> hdmi_high_tmds_clock_ratio
V5: Addressed review comments from Ville and Ander
- Do not modifiy the crtc_state after compute_config. Move all
scrambling and tmds_clock_ratio calcutations to compute_config.
- While setting scrambling for source/sink, do not check the
conditions again, just go by the crtc_state flags. This will
simplyfy the condition checks.
V6: Addressed review comments from Ville
- Do not add IS_GLK check in disable/enable function, instead add it
in compute_config, while setting state flags.
- Remove unnecessary paranthesis.
- Simplyfy handle_sink_scrambling function as suggested.
- Add readout code for scrambling status in get_ddi_config and add a
check for the same in pipe_config_compare.
V7: Addressed review comments from Ander/Ville
- No separate function for source scrambling, make it inline
- Align the last line of the macro TRANS_DDI_HDMI_SCRAMBLING_MASK
- Do not add platform check while setting source scrambling
- Use pipe_config instead of crtc->config to set sink scrambling
- To readout scrambling status, Compare with SCRAMBLING_MASK
not any of its bits
- Remove platform check in intel_pipe_config_compare while checking
scrambling status
V8: Fixed mege conflict, Addressed review comments from Ander
- Remove the desciption/comment about scrambling fom the caller, move
it to the function
- Move the IS_GLK check into scrambling function
- Fix alignment
V9: Fixed review comments from Ville, Ander
- Pass the scrambling state variables as bool input to the sink_scrambling
function and let the disable call be unconditional.
- Fix alignments in function calls and debug messages.
- Add kernel doc for function intel_hdmi_handle_sink_scrambling
V10: Rebase
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1489404244-16608-6-git-send-email-shashank.sharma@intel.com
All it does is pick the encoder and call intel_get_shared_dpll(). We
can just do this in the caller. One less indirection level during code
reading.
As another plus, now the two callers of intel_get_shared_dpll() are
{ironlake,haswell}_crtc_compute_clock().
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1490209125-20046-2-git-send-email-paulo.r.zanoni@intel.com
All the pre-SKL sprite planes compute the x/y/tile offsets in a
similar way. There are a couple of minor differences but the primary
planes have those as well. Thus i9xx_check_plane_surface()
already does what we need, so let's use it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170323192712.30682-7-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Computing the plane control register value is branchy so moving it out
from the plane commit hook seems prudent. Let's pre-compute it during
the atomic check phase and store the result in the plane state.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170323192712.30682-4-ville.syrjala@linux.intel.com
On SKL the planes are uniform so the "sprites" can use the
primary plane code perfectly fine. The only difference we
have is the color key handling, but since we never enable that
for the primary plane the same code works just fine.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170317211808.14693-3-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Backmerge drm-next to get at all the good stuff in drm-misc. We need
that because:
- drm_connector_list_iter conversion for i915 needs the core patches.
- Maarten's patches to use the new atomic state iterators also need
the core patches.
- We need the new link status property to complete the DP retraining
work, merging through 2 branches wasn't a good idea and we had to
partially backtrack.
- Chris needs reservation_object_trylock and we want to roll out
kref_read everywhere.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
4 weeks worth of stuff since I was traveling&lazy:
- lspcon improvements (Imre)
- proper atomic state for cdclk handling (Ville)
- gpu reset improvements (Chris)
- lots and lots of polish around fences, requests, waiting and
everything related all over (both gem and modeset code), from Chris
- atomic by default on gen5+ minus byt/bsw (Maarten did the patch to
flip the default, really this is a massive joint team effort)
- moar power domains, now 64bit (Ander)
- big pile of in-kernel unit tests for various gem subsystems (Chris),
including simple mock objects for i915 device and and the ggtt
manager.
- i915_gpu_info in debugfs, for taking a snapshot of the current gpu
state. Same thing as i915_error_state, but useful if the kernel didn't
notice something is stick. From Chris.
- bxt dsi fixes (Umar Shankar)
- bxt w/a updates (Jani)
- no more struct_mutex for gem object unreference (Chris)
- some execlist refactoring (Tvrtko)
- color manager support for glk (Ander)
- improve the power-well sync code to better take over from the
firmware (Imre)
- gem tracepoint polish (Tvrtko)
- lots of glk fixes all around (Ander)
- ctx switch improvements (Chris)
- glk dsi support&fixes (Deepak M)
- dsi fixes for vlv and clanups, lots of them (Hans de Goede)
- switch to i915.ko types in lots of our internal modeset code (Ander)
- byt/bsw atomic wm update code, yay (Ville)
* tag 'drm-intel-next-2017-03-06' of git://anongit.freedesktop.org/git/drm-intel: (432 commits)
drm/i915: Update DRIVER_DATE to 20170306
drm/i915: Don't use enums for hardware engine id
drm/i915: Split breadcrumbs spinlock into two
drm/i915: Refactor wakeup of the next breadcrumb waiter
drm/i915: Take reference for signaling the request from hardirq
drm/i915: Add FIFO underrun tracepoints
drm/i915: Add cxsr toggle tracepoint
drm/i915: Add VLV/CHV watermark/FIFO programming tracepoints
drm/i915: Add plane update/disable tracepoints
drm/i915: Kill level 0 wm hack for VLV/CHV
drm/i915: Workaround VLV/CHV sprite1->sprite0 enable underrun
drm/i915: Sanitize VLV/CHV watermarks properly
drm/i915: Only use update_wm_{pre,post} for pre-ilk platforms
drm/i915: Nuke crtc->wm.cxsr_allowed
drm/i915: Compute proper intermediate wms for vlv/cvh
drm/i915: Skip useless watermark/FIFO related work on VLV/CHV when not needed
drm/i915: Compute vlv/chv wms the atomic way
drm/i915: Compute VLV/CHV FIFO sizes based on the PM2 watermarks
drm/i915: Plop vlv/chv fifo sizes into crtc state
drm/i915: Plop vlv wm state into crtc_state
...
First slice of drm-misc-next for 4.12:
Core/subsystem-wide:
- link status core patch from Manasi, for signalling link train fail
to userspace. I also had the i915 patch in here, but that had a
small buglet in our CI, so reverted.
- more debugfs_remove removal from Noralf, almost there now (Noralf
said he'll try to follow up with the stragglers).
- drm todo moved into kerneldoc, for better visibility (see
Documentation/gpu/todo.rst), lots of starter tasks in there.
- devm_ of helpers + use it in sti (from Ben Gaignard, acked by Rob
Herring)
- extended framebuffer fbdev support (for fbdev flipping), and vblank
wait ioctl fbdev support (Maxime Ripard)
- misc small things all over, as usual
- add vblank callbacks to drm_crtc_funcs, plus make lots of good use
of this to simplify drivers (Shawn Guo)
- new atomic iterator macros to unconfuse old vs. new state
Small drivers:
- vc4 improvements from Eric
- vc4 kerneldocs (Eric)!
- tons of improvements for dw-mipi-dsi in rockchip from John Keeping
and Chris Zhong.
- MAINTAINERS entries for drivers managed in drm-misc. It's not yet
official, still an experiment, but definitely not complete fail and
better to avoid confusion. We kinda screwed that up with drm-misc a
bit when we started committers last year.
- qxl atomic conversion (Gabriel Krisman)
- bunch of virtual driver polish (qxl, virgl, ...)
- misc tiny patches all over
This is the first time we've done the same merge-window blackout for
drm-misc as we've done for drm-intel for ages, hence why we have a
_lot_ of stuff queued already. But it's still only half of drm-intel
(room to grow!), and the drivers in drm-misc experiment seems to work
at least insofar as that you also get lots of driver updates here
alredy.
* tag 'drm-misc-next-2017-03-06' of git://anongit.freedesktop.org/git/drm-misc: (141 commits)
drm/vc4: Fix OOPSes from trying to cache a partially constructed BO.
drm/vc4: Fulfill user BO creation requests from the kernel BO cache.
Revert "drm/i915: Implement Link Rate fallback on Link training failure"
drm/fb-helper: implement ioctl FBIO_WAITFORVSYNC
drm: Update drm_fbdev_cma_init documentation
drm/rockchip/dsi: add dw-mipi power domain support
drm/rockchip/dsi: fix insufficient bandwidth of some panel
dt-bindings: add power domain node for dw-mipi-rockchip
drm/rockchip/dsi: remove mode_valid function
drm/rockchip/dsi: dw-mipi: correct the coding style
drm/rockchip/dsi: dw-mipi: support RK3399 mipi dsi
dt-bindings: add rk3399 support for dw-mipi-rockchip
drm/rockchip: dw-mipi-dsi: add reset control
drm/rockchip: dw-mipi-dsi: support non-burst modes
drm/rockchip: dw-mipi-dsi: defer probe if panel is not loaded
drm/rockchip: vop: test for P{H,V}SYNC
drm/rockchip: dw-mipi-dsi: use positive check for N{H, V}SYNC
drm/rockchip: dw-mipi-dsi: use specific poll helper
drm/rockchip: dw-mipi-dsi: improve PLL configuration
drm/rockchip: dw-mipi-dsi: properly configure PHY timing
...
Clear out the watermark for all disabled planes to 0. This is required
to avoid falsely thinking that the inherited watermarks are bogus in
case the watermark is actually higher than the FIFO size.
v2: s/noninverted/raw/ for consistency with other platforms
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-13-ville.syrjala@linux.intel.com
Remove crtc->wm.cxsr_allowed and just rely on crtc_state->disable_cxsr
instead. This was used only by vlv/chv to indicate whether to enable
cxsr in the wm computation. That doesn't really work anymore, and as far
as the optimal watermarks go we'll just consider the number of planes
and the current pipe, and for the intermediate watermarks we'll also
start to consider disable_cxsr which is set appropriately when planes
are being enabled/disabled.
We'll also flip over the crtc_state->wm.need_postvbl_update setup so
that it's the wm code that will set it. Previously the generic code set
it up, and then the wm code cleared it again if it thought it's not
needed after all.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-11-ville.syrjala@linux.intel.com
Since the watermark registers arent double buffered on VLV/CHV, we'll
need to play around with intermediate watermarks same was as we do on
ILK-BDW.
The watermark registers on VLV/CHV contain inverted values, so to find
the intermediate watermark value we just take the minimum of the
active and optimal values. This also means that, unlike ILK-BDW,
there's no chance that we'd fail to find a working intermediate
watermarks. As long as both the active and optimal watermarks are valid
the intermediate watermarks will come out valid as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-10-ville.syrjala@linux.intel.com
Check whether anything relevant has actually change when we compute new
watermarks for each plane in the state. If the watermarks for no
primary/sprite planes changed we don't have to recompute the FIFO split
or reprogram the DSBARB registers. And even the cursor watermarks didn't
change we can skip the merge+invert step between all the planes on
the pipe as well.
v2: s/noninverted/raw/ for consistency with other platforms
v3: Drop duplicated vlv_get_fifo_size() call during init
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-9-ville.syrjala@linux.intel.com
Start computing the vlv/chv watermarks the atomic way, from the
.compute_pipe_wm() hook. We'll recompute the actual watermarks
for only planes that are part of the state, the other planes will
keep their watermark from the last time it was computed.
And the actual watermark programming will happen from the
.initial_watermarks() hook. For now we'll just compute the
optimal watermarks, and we'll hook up the intermediate
watermarks properly later.
The DSPARB registers responsible for the FIFO paritioning are
double buffered, so they will be programming from
intel_begin_crtc_commit().
v2: s/noninverted/raw/ for consistency with other platforms
s/vlv_plane_wm_set/vlv_raw_plane_wm_set/ for clarity
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-8-ville.syrjala@linux.intel.com
Let's compute the watermarks first and the FIFO size second. This way we
can make sure the FIFO split is the most accommodating to the watermarks.
Previously we could have potentially computed a FIFO split that couldn't
accommodate the PM2 watermarks simply due to a bad split even if the
total FIFO size would have been sufficient.
It'll also allow us to avoid recomputing the wms for all planes whenever
the FIFO split would change. Thus we don't have to add any extra planes
to the state when the FIFO needs to be repartitioned.
To help with this we'll keep around copies of the non-inverted
watermarks in the crtc state. For now that doesn't help too much, but
once we start to do the watermark computation only for the planes
that change we'll need the non-inverted values around for the other
planes.
v2: s/noninverted/raw/ for consistency with other platforms
Fix the memset() of the "raw" watermarks
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-7-ville.syrjala@linux.intel.com
Relocate the vlv/chv wm state to live under intel_crtc_state. Note
that for now this just behaves as a temporary storage. But it'll be
easier to conver the thing over to properly pre-computing the state
when it's already in the right place.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-5-ville.syrjala@linux.intel.com
Track the plane fifo sizes under intel_crtc instead of under each
intel_plane. Avoids looping over the planes in a bunch of places,
and later we'll move this tracking into the crtc state properly.
v2: Nuke intel_plane_wm_parameters (Maarten)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-3-ville.syrjala@linux.intel.com
In a lot of place we wish to know which planes on the crtc are actually
visible, or how many of them there are. Let's start tracking that in a
bitmask in the crtc state.
We already track enabled planes (ie. ones with an fb and crtc specified by
the user) but that's not quite the same thing as enabled planes may
still end up being invisible due to clipping and whatnot.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-2-ville.syrjala@linux.intel.com
Remove direct usages of intel_crtc->config from the DDI code. Functions
that didn't yet take a pipe_config as an argument were coverted to do
so.
v2: s/pipe_config/const crtc_state/ (Ville)
- take crtc from crtc_state. (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302125857.14665-7-ander.conselvan.de.oliveira@intel.com
Pass intel_crtc to functions intel_ddi_enable_transcoder_func(),
intel_ddi_set_pipe_settings() and intel_ddi_set_vc_payload_alloc(),
instead of the generic crtc type. By changing the functions
intel_ddi_get_crtc_encoder() so that it receives an intel_crtc
parameter, there is no need for the drm_crtc in the callers.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302125857.14665-6-ander.conselvan.de.oliveira@intel.com
It is preferred to pass pipe_config to functions instead of accessing
crtc->config directly. Follow suit and pass pipe_config to the fdi link
train functions.
v2: Add const; s/pipe_config/crtc_state/ (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302125857.14665-5-ander.conselvan.de.oliveira@intel.com
A long time ago we turned off the warning as it was too painful, we had
too much broken code. Turn it back on now as we are mostly clean and
need to prevent returning to such orangeness.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302074157.21631-2-chris@chris-wilson.co.uk
Reviewed-by: Imre Deak <imre.deak@intel.com>
This reverts commit 233ce881dd.
I assumed it's ok, but really should have double-checked - CI caught
tons of fail :(
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Acked-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170301171749.13053-1-daniel.vetter@ffwll.ch
We are going to split <linux/sched/clock.h> out of <linux/sched.h>, which
will have to be picked up from other headers and .c files.
Create a trivial placeholder <linux/sched/clock.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If link training at a link rate optimal for a particular
mode fails during modeset's atomic commit phase, then we
let the modeset complete and then retry. We save the link rate
value at which link training failed, update the link status property
to "BAD" and use a lower link rate to prune the modes. It will redo
the modeset on the current mode at lower link rate or if the current
mode gets pruned due to lower link constraints then, it will send a
hotplug uevent for userspace to handle it.
This is also required to pass DP CTS tests 4.3.1.3, 4.3.1.4,
4.3.1.6.
v9:
* Use the trimmed max values of link rate/lane count based on
link train fallback (Daniel Vetter)
v8:
* Set link_status to BAD first and then call mode_valid (Jani Nikula)
v7:
Remove the redundant variable in previous patch itself
v6:
* Obtain link rate index from fallback_link_rate using
the helper intel_dp_link_rate_index (Jani Nikula)
* Include fallback within intel_dp_start_link_train (Jani Nikula)
v5:
* Move set link status to drm core (Daniel Vetter, Jani Nikula)
v4:
* Add fallback support for non DDI platforms too
* Set connector->link status inside set_link_status function
(Jani Nikula)
v3:
* Set link status property to BAd unconditionally (Jani Nikula)
* Dont use two separate variables link_train_failed and link_status
to indicate same thing (Jani Nikula)
v2:
* Squashed a few patches (Jani Nikula)
Acked-by: Tony Cheng <tony.cheng@amd.com>
Acked-by: Harry Wentland <Harry.wentland@amd.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/d796cc0c2814d668a47ef43c464f9a4089d46d64.1481883920.git.jani.nikula@intel.com
According to bspec, the DDI IO power domains should be enabled after
enabling the DPLL and mapping it to the DDI. The current order doesn't
seem to create problems with Skylake and Kabylake, but causes enable
timeouts in Geminilake.
v2: Rebase.
- Take power domain references before sanitizing encoders. (Imre)
- Add comment to get_encoder_power_domains() defition. (Ander)
v3: Don't put the domain if called with HSW/BDW's analog encoder. (CI)
v4: Put IO power domain before unmapping DPLL. (Imre)
- Change return type of intel_ddi_get_power_domains() to u64. (Imre)
Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com> # v1
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224141959.5955-1-ander.conselvan.de.oliveira@intel.com
Don't allow conversion from arbitraty encoder types to a digital port.
Calling enc_to_dig_port() with the wrong encoder may seem far fetched,
but certain paths of the ddi code may be called with hasell's analog
encoder and the conversion is wrong for DP mst encoders too, so safe
guard against it.
v2: Warn if encoder type is unknown and device is not DDI. (Imre)
v3: Remove stray hunk from rebase error. (Ander)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224141845.5836-1-ander.conselvan.de.oliveira@intel.com
Rather than sprinkling ideas of how big the DDI buf translation tables
are somewhere in intel_dp.c, let's concentrate it all in intel_ddi.c
where the actual tables are defined. To that end we introduce
intel_ddi_dp_voltage_max() which will actually look at the proper
translation table to determine what is the maximum voltage swing level
supported.
v2: Mask out the preemphasis bits from the return value of
intel_ddi_dp_voltage_max()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170223174901.26749-1-ville.syrjala@linux.intel.com
-----BEGIN PGP SIGNATURE-----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=Yjfg
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.11-less-shouty' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.11.
Nothing too major, the tinydrm and mmu-less support should make
writing smaller drivers easier for some of the simpler platforms, and
there are a bunch of documentation updates.
Intel grew displayport MST audio support which is hopefully useful to
people, and FBC is on by default for GEN9+ (so people know where to
look for regressions). AMDGPU has a lot of fixes that would like new
firmware files installed for some GPUs.
Other than that it's pretty scattered all over.
I may have a follow up pull request as I know BenH has a bunch of AST
rework and fixes and I'd like to get those in once they've been tested
by AST, and I've got at least one pull request I'm just trying to get
the author to fix up.
Core:
- drm_mm reworked
- Connector list locking and iterators
- Documentation updates
- Format handling rework
- MMU-less support for fbdev helpers
- drm_crtc_from_index helper
- Core CRC API
- Remove drm_framebuffer_unregister_private
- Debugfs cleanup
- EDID/Infoframe fixes
- Release callback
- Tinydrm support (smaller drivers for simple hw)
panel:
- Add support for some new simple panels
i915:
- FBC by default for gen9+
- Shared dpll cleanups and docs
- GEN8 powerdomain cleanup
- DMC support on GLK
- DP MST audio support
- HuC loading support
- GVT init ordering fixes
- GVT IOMMU workaround fix
amdgpu/radeon:
- Power/clockgating improvements
- Preliminary SR-IOV support
- TTM buffer priority and eviction fixes
- SI DPM quirks removed due to firmware fixes
- Powerplay improvements
- VCE/UVD powergating fixes
- Cleanup SI GFX code to match CI/VI
- Support for > 2 displays on 3/5 crtc asics
- SI headless fixes
nouveau:
- Rework securre boot code in prep for GP10x secure boot
- Channel recovery improvements
- Initial power budget code
- MMU rework preperation
vmwgfx:
- Bunch of fixes and cleanups
exynos:
- Runtime PM support for MIC driver
- Cleanups to use atomic helpers
- UHD Support for TM2/TM2E boards
- Trigger mode fix for Rinato board
etnaviv:
- Shader performance fix
- Command stream validator fixes
- Command buffer suballocator
rockchip:
- CDN DisplayPort support
- IOMMU support for arm64 platform
imx-drm:
- Fix i.MX5 TV encoder probing
- Remove lower fb size limits
msm:
- Support for HW cursor on MDP5 devices
- DSI encoder cleanup
- GPU DT bindings cleanup
sti:
- stih410 cleanups
- Create fbdev at binding
- HQVDP fixes
- Remove stih416 chip functionality
- DVI/HDMI mode selection fixes
- FPS statistic reporting
omapdrm:
- IRQ code cleanup
dwi-hdmi bridge:
- Cleanups and fixes
adv-bridge:
- Updates for nexus
sii8520 bridge:
- Add interlace mode support
- Rework HDMI and lots of fixes
qxl:
- probing/teardown cleanups
ZTE drm:
- HDMI audio via SPDIF interface
- Video Layer overlay plane support
- Add TV encoder output device
atmel-hlcdc:
- Rework fbdev creation logic
tegra:
- OF node fix
fsl-dcu:
- Minor fixes
mali-dp:
- Assorted fixes
sunxi:
- Minor fix"
[ This was the "fixed" pull, that still had build warnings due to people
not even having build tested the result. I'm not a happy camper
I've fixed the things I noticed up in this merge. - Linus ]
* tag 'drm-for-v4.11-less-shouty' of git://people.freedesktop.org/~airlied/linux: (1177 commits)
lib/Kconfig: make PRIME_NUMBERS not user selectable
drm/tinydrm: helpers: Properly fix backlight dependency
drm/tinydrm: mipi-dbi: Fix field width specifier warning
drm/tinydrm: mipi-dbi: Silence: ‘cmd’ may be used uninitialized
drm/sti: fix build warnings in sti_drv.c and sti_vtg.c files
drm/amd/powerplay: fix PSI feature on Polars12
drm/amdgpu: refuse to reserve io mem for split VRAM buffers
drm/ttm: fix use-after-free races in vm fault handling
drm/tinydrm: Add support for Multi-Inno MI0283QT display
dt-bindings: Add Multi-Inno MI0283QT binding
dt-bindings: display/panel: Add common rotation property
of: Add vendor prefix for Multi-Inno
drm/tinydrm: Add MIPI DBI support
drm/tinydrm: Add helper functions
drm: Add DRM support for tiny LCD displays
drm/amd/amdgpu: post card if there is real hw resetting performed
drm/nouveau/tmr: provide backtrace when a timeout is hit
drm/nouveau/pci/g92: Fix rearm
drm/nouveau/drm/therm/fan: add a fallback if no fan control is specified in the vbios
drm/nouveau/hwmon: expose power_max and power_crit
..
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYoM2fAAoJEHm+PkMAQRiGr9MH/izEAMri7rJ0QMc3ejt+WmD0
8pkZw3+MVn71z6cIEgpzk4QkEWJd5rfhkETCeCp7qQ9V6cDW1FDE9+0OmPjiphDt
nnzKs7t7skEBwH5Mq5xygmIfkv+Z0QGHZ20gfQWY3F56Uxo+ARF88OBHBLKhqx3v
98C7YbMFLKBslKClA78NUEIdx0UfBaRqerlERx0Lfl9aoOrbBS6WI3iuREiylpih
9o7HTrwaGKkU4Kd6NdgJP2EyWPsd1LGalxBBjeDSpm5uokX6ALTdNXDZqcQscHjE
RmTqJTGRdhSThXOpNnvUJvk9L442yuNRrVme/IqLpxMdHPyjaXR3FGSIDb2SfjY=
=VMy8
-----END PGP SIGNATURE-----
Merge tag 'v4.10-rc8' into drm-next
Linux 4.10-rc8
Backmerge Linus rc8 to fix some conflicts, but also
to avoid pulling it in via a fixes pull from someone.
Verify that the refcount of all power wells match their HW enabled
state at the end of modeset HW state readout.
Also add documentation on how the reference count for each power well is
supposed to be acquired during initialization and HW state readout.
Suggested by Ander.
Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487345986-26511-6-git-send-email-imre.deak@intel.com
We do not need the BKL struct_mutex in order to allocate a GEM object,
nor to create the framebuffer, so resist the temptation to take the BKL
willy nilly. As this changes the locking contract around internal API
calls, the patch is a little larger than a plain removal of a pair of
mutex_lock/unlock.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170215105919.7347-2-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
During system resume time initialization the HPD level on LSPCON ports
can stay low for an extended amount of time, leading to failed AUX
transfers and LSPCON initialization. Fix this by waiting for HPD to get
asserted.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99178
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485509961-9010-3-git-send-email-imre.deak@intel.com
(cherry picked from commit 390b4e0024)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The max link parameters should be set/reset only on HPD or
connected boot case or on system resume.
Add a flag reset_link_params to intel_dp to decide when
to reset the max link parameters. This prevents the parameters
from getting reset/overwritten through all other
connector->funcs->detect() calls. This is important when link
training fails and the max link params are modified to the
lower fallback values.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1486515251-23469-1-git-send-email-manasi.d.navare@intel.com
The function intel_ddi_get_link_dpll() was added in f169660ed4
("drm/i915/dp: Add a standalone function to obtain shared dpll for
HSW/BDW/SKL/BXT") to "allow for the implementation of a platform
neutral upfront link training function", but such implementation
never landed.
So remove that function and clean up the exported shared DPLL interface.
Fixes: f169660ed4 ("drm/i915/dp: Add a standalone function to obtain shared dpll for HSW/BDW/SKL/BXT")
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484310032-1863-1-git-send-email-ander.conselvan.de.oliveira@intel.com
There are currently 30 power domains, which puts us pretty close to the
limit with 32 bit masks. Prepare for the future and increase the limit
to 64 bit.
v2: Rebase
v3: s/unsigned long long/u64/ (Joonas)
Allow the 64th bit of the mask to be used. (Joonas)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170209093121.24410-1-ander.conselvan.de.oliveira@intel.com
With the cdclk state, all the .modeset_commit_cdclk() hooks are
now pointless wrappers. Let's replace them with just a .set_cdclk()
function pointer. However let's wrap that in a small helper that
does the state comparison and prints a unified debug message across
all platforms. We didn't even have the debug print on all platforms
previously. This reduces the clutter in intel_atomic_commit_tail() a
little bit.
v2: Wrap .set_cdclk() in intel_set_cdclk()
v3: Add kernel-docs
v4: Deal with IS_GEN9_BC()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170126195201.32638-1-ville.syrjala@linux.intel.com
The current dev_cdclk vs. cdclk vs. atomic_cdclk_freq is quite a mess.
So here I'm introducing the "actual" and "logical" naming for our
cdclk state. "actual" is what we'll bash into the hardware and "logical"
is what everyone should use for state computaion/checking and whatnot.
We'll track both using the intel_cdclk_state as both will need other
differing parameters than just the actual cdclk frequency.
While doing that we can at the same time unify the appearance of the
.modeset_calc_cdclk() implementations a little bit.
v2: Commit dev_priv->cdclk.actual since that already has the
new state by the time .modeset_commit_cdclk() is called.
v3: s/locical/logical/ and improve the docs a bit
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170120182205.8141-9-ville.syrjala@linux.intel.com
Introduce intel_cdclk state which for now will track the cdclk
frequency, the vco frequency and the reference frequency (not sure we
want the last one, but I put it there anyway). We'll also make the
.get_cdclk() function fill out this state structure rather than
just returning the current cdclk frequency.
One immediate benefit is that calling .get_cdclk() will no longer
clobber state stored under dev_priv unless ex[plicitly told to do
so. Previously it clobbered the vco and reference clocks stored
there on some platforms.
We'll expand the use of this structure to actually precomputing the
state and whatnot later.
v2: Constify intel_cdclk_state_compare()
v3: Document intel_cdclk_state_compare()
v4: Deal with i945gm_get_cdclk()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170207183345.19763-1-ville.syrjala@linux.intel.com
Let's try to shrink intel_display.c a bit by moving the cdclk/rawclk
stuff to a new file. It's all reasonably self contained so we don't
even have to add that many non-static symbols.
We'll also take the opportunity to shuffle around the functions a bit
to get things in a more consistent order based on the platform.
v2: Add kernel-docs (Ander)
v3: Deal with IS_GEN9_BC()
v4: Deal with i945gm_get_cdclk()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170207183305.19656-1-ville.syrjala@linux.intel.com
Rather than recomputing the pipe pixel rate on demand everywhere, let's
just stick the precomputed value into the crtc state.
v2: Rebase due to min_pixclk[] code movement
Document the new pixel_rate struct member (Ander)
Combine vlv/chv with bdw+ in intel_modeset_readout_hw_state()
v3: Fix typos in commit message (David)
Cc: Ander Conselvan De Oliveira <conselvan2@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170126195031.32343-1-ville.syrjala@linux.intel.com
This effectively reverts
commit 489375c866
Author: Imre Deak <imre.deak@intel.com>
Date: Mon Oct 24 19:33:31 2016 +0300
drm/i915/lspcon: Add workaround for resuming in PCON mode
The workaround was added without considering that HPD is low during
the failed AUX transfers the WA fixed. Since the previous patch we
wait for HPD to get asserted. My tests also show that this happens
_after_ the DPCD reads start to return correct values. This
suggests that we don't need this WA any more, let's try to remove
it to reduce the clutter.
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485509961-9010-4-git-send-email-imre.deak@intel.com
During system resume time initialization the HPD level on LSPCON ports
can stay low for an extended amount of time, leading to failed AUX
transfers and LSPCON initialization. Fix this by waiting for HPD to get
asserted.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99178
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485509961-9010-3-git-send-email-imre.deak@intel.com
The intel_dp_autotest_video_pattern() function gets invoked through the
compliance test handler on a HPD short pulse if the test type is
set to DP_TEST_VIDEO_PATTERN. This performs the DPCD registers
reads to read the requested test pattern, video pattern resolution,
frame rate and bits per color value. The results of this analysis
are handed off to userspace so that the userspace app can set the
video pattern mode appropriately for the test result/response.
When the test is requested with specific BPC value, we read the BPC
value from the DPCD register. If this BPC value in intel_dp structure
has a non-zero value and we're on a display port connector, then we use
the value to calculate the bpp for the pipe. Also in this case if its
a 18bpp video pattern request, then we force the dithering on pipe to be
disabled since it causes CRC mismatches.
The compliance_test_active flag is set at the end of the individual
test handling functions. This is so that the kernel-side operations
can be completed without the risk of interruption from the userspace
app that is polling on that flag.
v5:
* Remove test_result variable
* Populate the compliance test data at the end of the function (Jani Nikula)
v4:
*Return TEST_NAK on read failures and invalid values (Jani Nikula)
* Address CRC mismatch errors
v3:
* Use the updated properly shifted bit definitions (Jani Nikula)
* Force dithering to be disabled on 18bpp compliance
test request (Manasi Navare)
v2:
* Updated the DPCD Register reads based on proper defines in header (Jani Nikula)
* Squahsed the patch that forced the pipe bpp to compliance test bpp (Jani Nikula)
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485274909-17470-1-git-send-email-manasi.d.navare@intel.com
This patch adds support to handle automated DP compliance
link training test requests. This patch has been tested with
Unigraf DPR-120 DP Compliance device for testing Link
Training Compliance.
After we get a short pulse Compliance test request, test
request values are read and hotplug uevent is sent in order
to trigger another modeset during which the pipe is configured
and link is retrained and enabled for link parameters requested
by the test.
v5:
* Only modify the compliance structure after all validation
is done (Jani Nikula)
* Remove the variable test_result (Jani Nikula)
v4:
* Return TEST_NAK for read failures and invalid
values (Jani Nikula)
* Conver the test link BW to link rate before storing (Jani Nikula)
v3:
* Validate the test link rate and lane count as soon as
the request comes (Jani Nikula)
v2:
* Validate the test lane count before using it in
intel_dp_compute_config (Jani Nikula)
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485274594-17361-1-git-send-email-manasi.d.navare@intel.com
Enable support for HDMI LPE audio mode on Baytrail and
Cherrytrail when HDaudio controller is not detected
Setup minimum required resources during i915_driver_load:
1. Create a platform device to share MMIO/IRQ resources
2. Make the platform device child of i915 device for runtime PM.
3. Create IRQ chip to forward HDMI LPE audio irqs.
HDMI LPE audio driver (a standalone sound driver) probes the
LPE audio device and creates a new sound card.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Jerome Anand <jerome.anand@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With atomic plane states we are able to track an allocation right from
preparation, during use and through to the final free after being
swapped out for a new plane. We can couple the VMA we pin for the
framebuffer (and its rotation) to this lifetime and avoid all the clumsy
lookups in between.
v2: Remove residual vma on plane cleanup (Chris)
v3: Add a description for the vma destruction in
intel_plane_destroy_state (Maarten)
References: https://bugs.freedesktop.org/show_bug.cgi?id=98829
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170116152131.18089-1-chris@chris-wilson.co.uk
Acked-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
The core provides now an ABI to userspace for generation of frame CRCs,
so implement the ->set_crc_source() callback and reuse as much code as
possible with the previous ABI implementation.
When handling the pageflip interrupt, we skip 1 or 2 frames depending on
the HW because they contain wrong values. For the legacy ABI for
generating frame CRCs, this was done in userspace but now that we have a
generic ABI it's better if it's not exposed by the kernel.
v2:
- Leave the legacy implementation in place as the ABI implementation
in the core is incompatible with it.
v3:
- Use the "cooked" vblank counter so we have a whole 32 bits.
- Make sure we don't mess with the state of the legacy CRC capture
ABI implementation.
v4:
- Keep use of get_vblank_counter as in the legacy code, will be
changed in a followup commit.
v5:
- Skip first frame or two as it's known that they contain wrong
data.
- A few fixes suggested by Emil Velikov.
v6:
- Rework programming of the HW registers to preserve previous
behavior.
v7:
- Address whitespace issue.
- Added a comment on why in the implementation of the new ABI we
skip the 1st or 2nd frames.
v9:
- Add stub for intel_crtc_set_crc_source.
v12:
- Rebased.
- Remove stub for intel_crtc_set_crc_source and instead set the
callback to NULL (Jani Nikula).
v15:
- Rebased.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Robert Foss <robert.foss@collabora.com>
irq
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170110134305.26326-2-tomeu.vizoso@collabora.com
Directly merge drm-misc into drm-intel since Dave is on vacation and
we need the various drm-misc patches (fb format rework, drm mm fixes,
selftest framework and others). Also pulled back -rc2 in first to
resync with drm-intel-fixes and make sure I can reuse the exact rerere
solutions from drm-tip for safety, and because I'm lazy.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The function intel_atomic_get_shared_dpll_state() is only called from
intel_dpll_mgr.c and it concerns the same data structures as the other
functions in that file, so move it there and make it static.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1483024933-3726-8-git-send-email-ander.conselvan.de.oliveira@intel.com
Do something similar to vc4, only allow updating the cursor state
in-place through a fastpath when the watermarks are unaffected. This
will allow cursor movement to be smooth, but changing cursor size or
showing/hiding cursor will still fall back so watermarks can be updated.
Only moving and changing fb is allowed.
Changes since v1:
- Set page flip to always_unused for trybot.
- Copy fence correctly, ignore plane_state->state, should be NULL.
- Check crtc_state for !active and modeset, go to slowpath if the case.
Changes since v2:
- Make error handling work correctly. (Matthew Auld)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/a8e4cb00-5171-14e5-bbe3-dadb654ff296@linux.intel.com
VLV apparently gets upset if the PPS for a pipe currently driving an
external DP port gets used for VDD stuff on another eDP port. The DP
port falls over and fails to retrain when this happens, leaving the
user staring at a black screen.
Let's fix it by also tracking which pipe is driving which DP/eDP port.
We'll track this under intel_dp so that we'll share the protection
of the pps_mutex alongside the pps_pipe tracking, since the two
things are intimately related.
I had plans to reduce the protection of pps_mutex to cover only eDP
ports, but with this we can't do that. Well, for for VLV/CHV at least.
For other platforms it should still be possible, which would allow
AUX communication to occur in parallel for multiple DP ports.
v2: Drop stray crap from a comment (Imre)
Grab pps_mutex when clearing active_pipe
Fix a typo in the commit message
v3: Make vlv_active_pipe() static
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1481738423-29738-1-git-send-email-ville.syrjala@linux.intel.com
<drm/drm_crtc.h> used to define most of the in-kernel KMS API. It has
now been split into separate files for each object type, but still
includes most other KMS headers to avoid breaking driver compilation.
As a step towards fixing that problem, remove the inclusion of
<drm/drm_encoder.h> from <drm/drm_crtc.h> and include it instead where
appropriate. Also remove the forward declarations of the drm_encoder and
drm_encoder_helper_funcs structures from <drm/drm_crtc.h> as they're not
needed in the header.
<drm/drm_encoder.h> now has to include <drm/drm_mode.h> and contain a
forward declaration of struct drm_encoder in order to allow including it
as the first header in a compilation unit.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sinclair Yeh <syeh@vmware.com> # For vmwgfx
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1481709550-29226-2-git-send-email-laurent.pinchart+renesas@ideasonboard.com
This patch does not change anything functionally, just cleans up
the DP compliance related variables and stores them all together
in a separate struct intel_dp_compliance. There is another struct
intel_dp_compliance_data to store all the test data. This makes it easy to
reset the compliance variables through a memset instead of
individual resetting.
v2:
* Removed functional changes for EDID (Jani Nikula)
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwl.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1481329371-16306-1-git-send-email-manasi.d.navare@intel.com
If link training fails, then we need to fallback to lower
link rate first and if link training fails at RBR, then
fallback to lower lane count.
This function finds the next lower link rate/lane count
value after link training failure and limits the max
link_rate and lane_count values to these fallback values.
v7:
* Remove unnecessary intializations and remove redundant
call to intel_dp_common_rates (Jani Nikula)
v6:
* Cap the max link rate and lane count to the max
values obtained during fallback link training (Daniel Vetter)
v5:
* Start the fallback at the lane count value passed not
the max lane count (Jani Nikula)
v4:
* Remove the redundant variable link_train_failed
v3:
* Remove fallback_link_rate_index variable, just obtain
that using the helper intel_dp_link_rate_index (Jani Nikula)
v2:
Squash the patch that returns the link rate index (Jani Nikula)
Acked-by: Tony Cheng <tony.cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1481252712-12925-1-git-send-email-manasi.d.navare@intel.com
Sink's capabilities are advertised through DPCD registers and get
updated only on hotplug. So they should be computed only once in the
long pulse handler and saved off in intel_dp structure for the use
later. For this reason two new fields max_sink_lane_count and
max_sink_link_bw are added to intel_dp structure.
This also simplifies the fallback link rate/lane count logic
to handle link training failure. In that case, the max_sink_link_bw
and max_sink_lane_count can be reccomputed to match the fallback
values lowering the sink capabilities due to link train failure.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1480984058-552-3-git-send-email-manasi.d.navare@intel.com
In preparation to using a generic API in the DRM core for continuous CRC
generation, move the related code out of i915_debugfs.c into a new file.
Eventually, only the Intel-specific code will remain in this new file.
v2: Rebased.
v6: Rebased.
v7: Fix whitespace issue.
v9: Have intel_display_crc_init accept a drm_i915_private instead.
v12: Rebased.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1481545788-18194-1-git-send-email-tomeu.vizoso@collabora.com
This patch Adds a function to extract intel_crtc_state from the
atomic_state, if not available it returns NULL.
v2 (from Paulo):
- Fix white space problem detected by checkpatch.
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161201154940.24446-7-mahesh1.kumar@intel.com
Not validating the mode rate against max. link rate results in not pruning
invalid modes. For e.g, a HBR2 5.4 Gbps 2-lane configuration does not
support 4k@60Hz. But, we do not reject this mode.
So, make use of the helpers in intel_dp to validate mode data rate against
max. link data rate of a configuration.
v3: Renamed local variables again for consistency (Manasi)
v2: Renamed mode data rate local variable to be more explanatory.
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479243546-17189-1-git-send-email-dhinakaran.pandiyan@intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Prepare for using the same code for judging ddi being audio enabled.
No functional changes.
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Lyude <cpaul@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1480334827-112273-2-git-send-email-libin.yang@intel.com
99% of the time we access i915_address_space->dev we want the i915
device and not the drm device, so let's store the drm_i915_private
backpointer instead. The only real complication here are the inlines
in i915_vma.h where drm_i915_private is not yet defined and so we have
to choose an alternate path for our asserts.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161129095008.32622-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Pass dev_priv to intel_setup_outputs() and functions called by it, since
those are all intel i915 specific functions. Also, in the majority of
the functions dev_priv is used more often than dev. In the rare cases
where there are a few calls back into drm core, a local dev variable was
added.
v2: Don't convert dev to &dev_priv->drm in intel_dsi_init. (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479910904-11005-1-git-send-email-ander.conselvan.de.oliveira@intel.com
In all cases we can now obtain the relevant crtc_state/conn_state
from the relevant callbacks, which means all the ->config accesses
can be removed and the code cleaned up.
Changes since v1:
- cstate -> crtc_state
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/8b02a6b4-606a-e43a-b357-ad17f491525b@linux.intel.com
[mlankhorst: Reinstate missing comment]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Add a mask of which planes are available for each pipe. This doesn't
quite work for old platforms with dynamic plane<->pipe assignment, but
as we don't support that sort of stuff (yet) we can get away with it.
The main use I have for this is the for_each_plane_id_on_crtc() macro
for iterating over all possible planes on the crtc. I suppose we could
not add the mask, and instead iterate by comparing intel_plane->pipe
but then we'd need a local intel_plane variable which is just
unnecessary clutter in some cases. But I'm not hung up on this, so if
people prefer the other option I could be convinced to use it.
v2: Use BIT() in the iterator macro too (Paulo)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479830524-7882-3-git-send-email-ville.syrjala@linux.intel.com
As I told people in [1] we really should not be confusing enum plane
as a per-pipe plane identifier. Looks like that happened nonetheless, so
let's fix it up by splitting the two into two enums.
We'll also want something we just directly pass to various register
offset macros and whatnot on SKL+. So let's make this new thing work for that.
Currently we pass intel_plane->plane for the "sprites" and just a
hardcoded zero for the "primary" planes. We want to get rid of that
hardocoding so that we can share the same code for all planes (apart
from the legacy cursor of course).
[1] https://lists.freedesktop.org/archives/intel-gfx/2015-September/076082.html
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479830524-7882-2-git-send-email-ville.syrjala@linux.intel.com
Some LSPCON adaptors may return an incorrect LSPCON mode right after
waking from DP Sleep state. This is the case at least for the ParadTech
PS175 adaptor, both when waking because of exiting the DP Sleep to
active state, or due to any other AUX CH transfer. We can determine the
current expected mode based on whether the DPCD area is accessible,
since according to the LSPCON spec this area is only accesible
in PCON mode.
This wait will avoid us trying to change the mode, while the current
expected mode hasn't settled yet and start link training before the
adaptor thinks it's in PCON mode after waking from DP Sleep state.
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479755707-29596-4-git-send-email-imre.deak@intel.com
And as usual a little bit of cascaded function prototype changes.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
The graphics driver is supposed to define the DIDL, which are used for
_DOD, not the BIOS. Restore that behaviour.
This is basically a revert of
commit 3143751ff5
Author: Zhang Rui <rui.zhang@intel.com>
Date: Mon Mar 29 15:12:16 2010 +0800
drm/i915: set DIDL using the ACPI video output device _ADR method return.
which went out of its way to cater to a specific BIOS, setting up DIDL
based on _ADR method. Perhaps that approach worked on that specific
machine, but on the machines I checked the _ADR method invents the
device identifiers out of thin air if DIDL has not been set. The source
for _ADR is also supposed to be the DIDL set by the driver, not the
other way around.
With this, we'll also limit the number of outputs to what the driver
actually has.
A side effect of this change is that the DIDL, and by proxy CADL, will
be initialized in the order of the connector list. That, in turn, has
internal panels in front, ensuring they're included in the DIDL and CADL
lists. Hopefully this ensures the BIOS does not block backlight hotkey
events, thinking the internal panel is off.
v2: do not set ACPI_DEVICE_ID_SCHEME in the device id (Peter Wu)
v3: Rebase
Cc: Peter Wu <peter@lekensteyn.nl>
Cc: Rainer Koenig <Rainer.Koenig@ts.fujitsu.com>
Cc: Jan-Marek Glogowski <glogow@fbihome.de>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Cc: Paolo Stivanin <paolostivanin@fastmail.fm>
Tested-by: Rainer Koenig <Rainer.Koenig@ts.fujitsu.com>
Tested-by: Paolo Stivanin <paolostivanin@fastmail.fm>
Tested-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Reviewed-and-tested-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/9660d29cf310c17bbf4d58c0e09d5b047446e2d5.1479295490.git.jani.nikula@intel.com
dev_priv->hw_ddb is only used by skl_update_crtcs, but the ddb
allocation for each pipe is calculated in crtc_state.
We can rid of the global member by looking at crtc_state.
Do this by saving all active old ddb allocations from the old crtc_state
in an array, and then point them to the new allocation every time we update
a crtc.
This will allow us to keep track of the intermediate ddb allocations,
which is what hw_ddb was previously used for. With hw_ddb gone all
SKL-style watermark values are properly maintained only in crtc_state.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1478609742-13603-5-git-send-email-maarten.lankhorst@linux.intel.com
[mlankhorst: Reword commit message.]
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
The watermark updates for SKL style watermarks are no longer done
in the plane callbacks, but are now called in a separate watermark
update function that's called during the same vblank evasion,
before the plane updates.
This also gets rid of the global skl_results, which was required for
keeping track of the current atomic commit.
Changes since v1:
- Move line unwrap to correct patch. (Lyude)
- Make sure we don't regress ILK watermarks. (Matt)
- Rephrase commit message. (Matt)
Changes since v2:
- Fix disable watermark check to use the correct way to determine single
step watermark support.
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lyude <cpaul@redhat.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1478609742-13603-3-git-send-email-maarten.lankhorst@linux.intel.com
[mlankhorst: Small whitespace fix in skl_initial_wm]
drm_select_eld requires mode_config.mutex and connection_mutex
because it looks at the connector list and at the legacy encoders.
This is not required, because when we call audio_codec_enable we know
which connector it was called for, so pass the state.
This also removes having to look at crtc->config.
Changes since v1:
- Use intel_crtc->pipe instead of drm_crtc_index. (Ville)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1478609742-13603-8-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
There's no need to keep a duplicate skl_pipe_wm around any more,
everything can be discovered from crtc_state, which we pass around
correctly now even in case of plane disable.
The copy in intel_crtc->wm.skl.active is equal to
crtc_state->wm.skl.optimal after the atomic commit completes.
It's useful for two-step watermark programming, but not required for
gen9+ which does it in a single step. We can pull the old allocation
from old_crtc_state.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1477489299-25777-9-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
It's only used in one function, and can be calculated without caching it
in the global struct by using drm_atomic_crtc_state_for_each_plane_state.
There are loops over all planes, including planes that don't exist.
This is harmless, because data_rate will always be 0 for them and we
never program them when updating watermarks.
Changes since v1:
- Rename rate back to data_rate, and change array name to
plane_data_rate. (Matt)
- Remove whitespace. (Paulo)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1477489299-25777-5-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Due to the plane->index not getting readjusted in drm_plane_cleanup(),
we can't continue initialization of some plane/crtc init fails.
Well, we sort of could I suppose if we left all initialized planes on
the list, but that would expose those planes to userspace as well.
But for crtcs the situation is even worse since we assume that
pipe==crtc index occasionally, so we can't really deal with a partially
initialize set of crtcs.
So seems safest to just abort the entire thing if anything goes wrong.
All the failure paths here are kmalloc()s anyway, so it seems unlikely
we'd get very far if these start failing.
v2: Add (enum plane) case to silence gcc
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1477411083-19255-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After combining the dma-buf reservation object and the GEM reservation
object, we lost the ability to do a nonblocking wait on the i915 request
(as we blocked upon the reservation object during prepare_fb). We can
instead convert the reservation object into a fence upon which we can
asynchronously wait (including a forced timeout in case the DMA fence is
never signaled).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161028125858.23563-22-chris@chris-wilson.co.uk
In preparation to support many distinct timelines, we need to expand the
activity tracking on the GEM object to handle more than just a request
per engine. We already use the struct reservation_object on the dma-buf
to handle many fence contexts, so integrating that into the GEM object
itself is the preferred solution. (For example, we can now share the same
reservation_object between every consumer/producer using this buffer and
skip the manual import/export via dma-buf.)
v2: Reimplement busy-ioctl (by walking the reservation object), postpone
the ABI change for another day. Similarly use the reservation object to
find the last_write request (if active and from i915) for choosing
display CS flips.
Caveats:
* busy-ioctl: busy-ioctl only reports on the native fences, it will not
warn of stalls (in set-domain-ioctl, pread/pwrite etc) if the object is
being rendered to by external fences. It also will not report the same
busy state as wait-ioctl (or polling on the dma-buf) in the same
circumstances. On the plus side, it does retain reporting of which
*i915* engines are engaged with this object.
* non-blocking atomic modesets take a step backwards as the wait for
render completion blocks the ioctl. This is fixed in a subsequent
patch to use a fence instead for awaiting on the rendering, see
"drm/i915: Restore nonblocking awaits for modesetting"
* dynamic array manipulation for shared-fences in reservation is slower
than the previous lockless static assignment (e.g. gem_exec_lut_handle
runtime on ivb goes from 42s to 66s), mainly due to atomic operations
(maintaining the fence refcounts).
* loss of object-level retirement callbacks, emulated by VMA retirement
tracking.
* minor loss of object-level last activity information from debugfs,
could be replaced with per-vma information if desired
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161028125858.23563-21-chris@chris-wilson.co.uk
On my APL the LSPCON firmware resumes in PCON mode as opposed to the
expected LS mode. It also appears to be in a state where AUX DPCD reads
will succeed but return garbage recovering only after a few hundreds of
milliseconds. After the recovery time DPCD reads will result in the
correct values and things will continue to work. If I2C over AUX is
attempted during this recovery time (implying an AUX write transaction)
the firmware won't recover and will stay in this broken state.
As a workaround check if the firmware is in PCON state after resume and
if so wait until the correct DPCD values are returned. For this we
compare the branch descriptor with the one we cached during init time.
If the firmware was in the LS state, we skip the w/a and continue as
before.
v2:
- Use the DP descriptor value cached in intel_dp. (Jani)
- Get to intel_dp using container_of(), instead of a cached ptr.
(Shashank)
- Use usleep_range() instead of msleep().
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98353
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1477326811-30431-9-git-send-email-imre.deak@intel.com
We can use the container_of() magic to get to the DDC adapter, so no
need for caching a pointer to it. We'll also need to get at the intel_dp
ptr in the following patch, so add a helper that can be used for both
purposes.
Cc: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1477326811-30431-8-git-send-email-imre.deak@intel.com
As for external DP sink and branch devices read and print the DP
descriptor for eDP and LSPCON devices as well to aid debugging.
v2:
- Split out this change to a separate patch. (Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1477326811-30431-7-git-send-email-imre.deak@intel.com
All types of DP devices (eDP, DP sink, DP branch) will fail their probe
if the start of DPCD can't be read. The LSPCON PCON functionality also
depends on accessing this area, so fail the probe if the read fails.
Cc: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1477326811-30431-6-git-send-email-imre.deak@intel.com
Extend the branch/sink descriptor info with the missing device ID
field. While at it also read out all the descriptor registers in one
transfer and make the debug print more compact.
v2: (Jani)
- Cache the descriptor in intel_dp.
- Split out this change into a separate patch.
v3: (Jani)
- Fix return value check of __intel_dp_read_desc().
- Use %pE instead of %s to print the device ID.
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1477401159-15098-1-git-send-email-imre.deak@intel.com
There are certain types of interrupts which Host can receive from GuC.
GuC ukernel sends an interrupt to Host for certain events, like for
example retrieve/consume the logs generated by ukernel.
This patch adds support to receive interrupts from GuC but currently
enables & partially handles only the interrupt sent by GuC ukernel.
Future patches will add support for handling other interrupt types.
v2:
- Use common low level routines for PM IER/IIR programming (Chris)
- Rename interrupt functions to gen9_xxx from gen8_xxx (Chris)
- Replace disabling of wake ref asserts with rpm get/put (Chris)
v3:
- Update comments for more clarity. (Tvrtko)
- Remove the masking of GuC interrupt, which was kept masked till the
start of bottom half, its not really needed as there is only a
single instance of work item & wq is ordered. (Tvrtko)
v4:
- Rebase.
- Rename guc_events to pm_guc_events so as to be indicative of the
register/control block it is associated with. (Chris)
- Add handling for back to back log buffer flush interrupts.
v5:
- Move the read & clearing of register, containing Guc2Host message
bits, outside the irq spinlock. (Tvrtko)
v6:
- Move the log buffer flush interrupt related stuff to the following
patch so as to do only generic bits in this patch. (Tvrtko)
- Rebase.
v7:
- Remove the interrupts_enabled check from gen9_guc_irq_handler, want to
process that last interrupt also before disabling the interrupt, sync
against the work queued by irq handler will be done by caller disabling
the interrupt.
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
So far PM IER/IIR/IMR registers were being used only for Turbo related
interrupts. But interrupts coming from GuC also use the same set.
As a precursor to supporting GuC interrupts, added new low level routines
so as to allow sharing the programming of PM IER/IIR/IMR registers between
Turbo & GuC.
Also similar to PM IMR, maintaining a bitmask for PM IER register, to allow
easy sharing of it between Turbo & GuC without involving a rmw operation.
v2:
- For appropriateness & avoid any ambiguity, rename old functions
enable/disable pm_irq to mask/unmask pm_irq and rename new functions
enable/disable pm_interrupts to enable/disable pm_irq. (Tvrtko)
- Use u32 in place of uint32_t. (Tvrtko)
v3:
- Rename the fields pm_irq_mask & pm_ier_mask and do some cleanup. (Chris)
- Rebase.
v4: Fix the inadvertent disabling of User interrupt for VECS ring causing
failure for certain IGTs.
v5: Use dev_priv with HAS_VEBOX macro. (Tvrtko)
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Backmerge because Chris Wilson needs the very latest&greates of
Gustavo Padovan's sync_file work, specifically the refcounting changes
from:
commit 30cd85dd6e
Author: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Date: Wed Oct 19 15:48:32 2016 -0200
dma-buf/sync_file: hold reference to fence when creating sync_file
Also good to sync in general since git tends to get confused with the
cherry-picking going on.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
- first slice of the gvt device model (Zhenyu et al)
- compression support for gpu error states (Chris)
- sunset clause on gpu errors resulting in dmesg noise telling users
how to report them
- .rodata diet from Tvrtko
- switch over lots of macros to only take dev_priv (Tvrtko)
- underrun suppression for dp link training (Ville)
- lspcon (hmdi 2.0 on skl/bxt) support from Shashank Sharma, polish
from Jani
- gen9 wm fixes from Paulo&Lyude
- updated ddi programming for kbl (Rodrigo)
- respect alternate aux/ddc pins (from vbt) for all ddi ports (Ville)
* tag 'drm-intel-next-2016-10-24' of git://anongit.freedesktop.org/drm-intel: (227 commits)
drm/i915: Update DRIVER_DATE to 20161024
drm/i915: Stop setting SNB min-freq-table 0 on powersave setup
drm/i915/dp: add lane_count check in intel_dp_check_link_status
drm/i915: Fix whitespace issues
drm/i915: Clean up DDI DDC/AUX CH sanitation
drm/i915: Respect alternate_ddc_pin for all DDI ports
drm/i915: Respect alternate_aux_channel for all DDI ports
drm/i915/gen9: Remove WaEnableYV12BugFixInHalfSliceChicken7
drm/i915: KBL - Recommended buffer translation programming for DisplayPort
drm/i915: Move down skl/kbl ddi iboost and n_edp_entires fixup
drm/i915: Add a sunset clause to GPU hang logging
drm/i915: Stop reporting error details in dmesg as well as the error-state
drm/i915/gvt: do not ignore return value of create_scratch_page
drm/i915/gvt: fix spare warnings on odd constant _Bool cast
drm/i915/gvt: mark symbols static where possible
drm/i915/gvt: fix sparse warnings on different address spaces
drm/i915/gvt: properly access enabled intel_engine_cs
drm/i915/gvt: Remove defunct vmap_batch()
drm/i915/gvt: Use common mapping routines for shadow_bb object
drm/i915/gvt: Use common mapping routines for indirect_ctx object
...
First -misc pull for 4.10:
- drm_format rework from Laurent
- reservation patches from Chris that missed 4.9.
- aspect ratio support in infoframe helpers and drm mode/edid code
(Shashank Sharma)
- rotation rework from Ville (first parts at least)
- another attempt at the CRC debugfs interface from Tomeu
- piles and piles of misc patches all over
* tag 'topic/drm-misc-2016-10-24' of git://anongit.freedesktop.org/drm-intel: (55 commits)
drm: Use u64 for intermediate dotclock calculations
drm/i915: Use the per-plane rotation property
drm/omap: Use per-plane rotation property
drm/omap: Set rotation property initial value to BIT(DRM_ROTATE_0) insted of 0
drm/atmel-hlcdc: Use per-plane rotation property
drm/arm: Use per-plane rotation property
drm: Add support for optional per-plane rotation property
drm/atomic: Reject attempts to use multiple rotation angles at once
drm: Add drm_rotation_90_or_270()
dma-buf/sync_file: hold reference to fence when creating sync_file
drm/virtio: kconfig: Fixup white space.
drm/fence: release fence reference when canceling event
drm/i915: Handle early failure during intel_get_load_detect_pipe
drm/fb_cma_helper: do not free fbdev if there is none
drm: fix sparse warnings on undeclared symbols in crc debugfs
gpu: Remove depends on RESET_CONTROLLER when not a provider
i915: don't call drm_atomic_state_put on invalid pointer
drm: Don't export the drm_fb_get_bpp_depth() function
drm/arm: mali-dp: Replace drm_fb_get_bpp_depth() with drm_format_plane_cpp()
drm: vmwgfx: Replace drm_fb_get_bpp_depth() with drm_format_info()
...
We only used the RPM sequence checking inside the lowlevel GTT
accessors, when we had to rely on callers taking the wakeref on our
behalf. Now that we take the RPM wakeref inside the GTT management
routines themselves, we can forgo the sanitycheck of the callers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161024124218.18252-4-chris@chris-wilson.co.uk
Maarten Lankhorst