The MHI device may be in the syserr state when we attempt to init it in
power_up(). Since we have no local state, the handling is simple -
reset the device and wait for it to transition out of the reset state.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-15-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take write lock only to protect db_mode member of mhi channel.
This allows rest of the mhi channels to just take read lock which
fine grains the locking. It prevents channel readers to starve if
they try to enter critical section after a writer.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-14-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Devices that support RDDM do not require processing SYS_ERROR as it is
deemed redundant. Avoid SYS_ERROR processing if RDDM is supported by
the device.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-13-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver continues handling of BHI interrupt even if MHI register access
is not allowed. By doing so it calls the status call back and performs
early notification for the MHI client. This is not needed when MHI
register access is not allowed. Hence skip the handling in this case and
return. Also add debug log to print device state, local EE and device EE
when reg access is valid.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-12-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mission mode transition is handled by state worker thread but
power off is not. There is a possibility while mission mode
transition is in progress which calls MHI client driver probe,
power off is issued by MHI controller. This results into client
driver probe and remove running in parallel and causes use after
free situation. By queuing disable transition work when mission
mode is in progress prevents the race condition.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-11-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the system error worker thread and instead have the
execution environment worker handle that transition to serialize
processing and avoid any possible race conditions during
shutdown.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-10-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While writing any sequence or session identifiers, it is possible that
the host could write a zero value, whereas only non-zero values should
be supported writes to those registers. Ensure that the host does not
write a non-zero value for them and also log them in debug messages. A
macro is introduced to simplify this check and the existing checks are
also converted to use this macro.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-9-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When loading AMSS firmware using BHIe protocol, return -ETIMEDOUT if no
response is received within the timeout or return -EIO in case of a
protocol returned failure or an MHI error state.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-7-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upon power up, driver queues firmware worker thread if the execution
environment is PBL. Firmware worker is blocked with a timeout until
state worker gets a chance to run and unblock firmware worker. An
endpoint power up failure can be seen if state worker gets a chance to
run after firmware worker has timed out. Remove this dependency and
handle firmware load directly using state worker thread.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-6-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When MHI Driver receives an EOT event, it reads xfer_len from the
event in the last TRE. The value is under control of the MHI device
and never validated by Host MHI driver. The value should never be
larger than the real size of the buffer but a malicious device can
set the value 0xFFFF as maximum. This causes driver to memory
overflow (both read or write). Fix this issue by reading minimum of
transfer length from event and the buffer length provided.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MHI data completion handler function reads channel id from event
ring element. Value is under the control of MHI devices and can be
any value between 0 and 255. In order to prevent out of bound access
add a bound check against the max channel supported by controller
and skip processing of that event ring element.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver is using zero initialized intmod value from mhi channel when
configuring TRE for bei field. This prevents interrupt moderation to
take effect in case it is supported by an event ring. Fix this by
copying intmod value from associated event ring to mhi channel upon
registering mhi controller.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move all the common code to generate TRE from mhi_queue_buf,
mhi_queue_dma and mhi_queue_skb to mhi_gen_tre. This helps
to centralize the TRE generation code which makes any future
bug fixing easier to manage in these APIs.
Suggested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When multiple instances of the same MHI product are present in a system,
we can see a splat from mhi_create_devices() - "sysfs: cannot create
duplicate filename".
This is because the device names assigned to the MHI channel devices are
non-unique. They consist of the channel's name, and the channel's pipe
id. For identical products, each instance is going to have the same
set of channel (both in name and pipe id).
To fix this, we prepend the device name of the parent device that the
MHI channels belong to. Since different instances of the same product
should have unique device names, this makes the MHI channel devices for
each product also unique.
Additionally, remove the pipe id from the MHI channel device name. This
is an internal detail to the MHI product that provides little value, and
imposes too much device specific internal details to userspace. It is
expected that channel with a specific name (ie "SAHARA") has a specific
client, and it does not matter what pipe id that channel is enumerated on.
The pipe id is an internal detail between the MHI bus, and the hardware.
The client is not expected to make decisions based on the pipe id, and to
do so would require the client to have intimate knowledge of the hardware,
which is inappropiate as it may violate the layering provided by the MHI
bus. The limitation of doing this is that each product may only have one
instance of a channel by a unique name. This limitation is appropriate
given the usecases of MHI channels.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200430190555.32741-7-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When reading or writing MHI registers, the core assumes that the physical
link is a memory mapped PCI link. This assumption may not hold for all
MHI devices. The controller knows what is the physical link (ie PCI, I2C,
SPI, etc), and therefore knows the proper methods to access that link.
The controller can also handle link specific error scenarios, such as
reading -1 when the PCI link went down.
Therefore, it is appropriate that the MHI core requests the controller to
make register accesses on behalf of the core, which abstracts the core
from link specifics, and end up removing an unnecessary assumption.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200430190555.32741-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the MHI core detects invalid data due to a PCI read, it calls into
the controller via link_status() to double check that the link is infact
down. All in all, this is pretty pointless, and racy. There are no good
reasons for this, and only drawbacks.
Its pointless because chances are, the controller is going to do the same
thing to determine if the link is down - attempt a PCI access and compare
the result. This does not make the link status decision any smarter.
Its racy because its possible that the link was down at the time of the
MHI core access, but then recovered before the controller access. In this
case, the controller will indicate the link is not down, and the MHI core
will precede to use a bad value as the MHI core does not attempt to retry
the access.
Retrying the access in the MHI core is a bad idea because again, it is
racy - what if the link is down again? Furthermore, there may be some
higher level state associated with the link status, that is now invalid
because the link went down.
The only reason why the MHI core could see "invalid" data when doing a PCI
access, that is actually valid, is if the register actually contained the
PCI spec defined sentinel for an invalid access. In this case, it is
arguable that the MHI implementation broken, and should be fixed, not
worked around.
Therefore, remove the link_status() callback before anyone attempts to
implement it.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200430190555.32741-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Powerdown is necessary if mhi_sync_power_up fails due to a timeout, to
clean up the resources. Otherwise a BUG could be triggered when
attempting to clean up MSIs because the IRQ is still active from a
request_irq().
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200430190555.32741-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mhi_alloc_device() function never returns NULL, it returns error
pointers.
Fixes: da1c4f8569 ("bus: mhi: core: Add support for creating and destroying MHI devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200407093133.GM68494@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for MHI suspend and resume states. While at it, the
mhi_notify() function needs to be exported as well.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200427075829.9304-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These are the usual updates for SoC specific device drivers and related
subsystems that don't have their own top-level maintainers:
- ARM SCMI/SCPI updates to allow pluggable transport layers
- TEE subsystem cleanups
- A new driver for the Amlogic secure power domain controller
- Various driver updates for the NXP Layerscape DPAA2, NXP i.MX SCU and
TI OMAP2+ sysc drivers.
- Qualcomm SoC driver updates, including a new library module for
"protection domain" notifications
- Lots of smaller bugfixes and cleanups in other drivers
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=qbsP
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM driver updates from Arnd Bergmann:
"These are the usual updates for SoC specific device drivers and
related subsystems that don't have their own top-level maintainers:
- ARM SCMI/SCPI updates to allow pluggable transport layers
- TEE subsystem cleanups
- A new driver for the Amlogic secure power domain controller
- Various driver updates for the NXP Layerscape DPAA2, NXP i.MX SCU
and TI OMAP2+ sysc drivers.
- Qualcomm SoC driver updates, including a new library module for
"protection domain" notifications
- Lots of smaller bugfixes and cleanups in other drivers"
* tag 'arm-drivers-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (70 commits)
soc: fsl: qe: fix sparse warnings for ucc_slow.c
soc: fsl: qe: ucc_slow: remove 0 assignment for kzalloc'ed structure
soc: fsl: qe: fix sparse warnings for ucc_fast.c
soc: fsl: qe: fix sparse warnings for qe_ic.c
soc: fsl: qe: fix sparse warnings for ucc.c
soc: fsl: qe: fix sparse warning for qe_common.c
soc: fsl: qe: fix sparse warnings for qe.c
soc: qcom: Fix QCOM_APR dependencies
soc: qcom: pdr: Avoid uninitialized use of found in pdr_indication_cb
soc: imx: drop COMPILE_TEST for IMX_SCU_SOC
firmware: imx: add COMPILE_TEST for IMX_SCU driver
soc: imx: gpc: fix power up sequencing
soc: imx: increase build coverage for imx8m soc driver
soc: qcom: apr: Add avs/audio tracking functionality
dt-bindings: soc: qcom: apr: Add protection domain bindings
soc: qcom: Introduce Protection Domain Restart helpers
devicetree: bindings: firmware: add ipq806x to qcom_scm
memory: tegra: Correct debugfs clk rate-range on Tegra124
memory: tegra: Correct debugfs clk rate-range on Tegra30
memory: tegra: Correct debugfs clk rate-range on Tegra20
...
Here is the big set of char/misc/other driver patches for 5.7-rc1.
Lots of things in here, and it's later than expected due to some reverts
to resolve some reported issues. All is now clean with no reported
problems in linux-next.
Included in here is:
- interconnect updates
- mei driver updates
- uio updates
- nvmem driver updates
- soundwire updates
- binderfs updates
- coresight updates
- habanalabs updates
- mhi new bus type and core
- extcon driver updates
- some Kconfig cleanups
- other small misc driver cleanups and updates
As mentioned, all have been in linux-next for a while, and with the last
two reverts, all is calm and good.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXodfvA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynzCQCfROhar3E8EhYEqSOP6xq6uhX9uegAnRgGY2rs
rN4JJpOcTddvZcVlD+vo
=ocWk
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char/misc/other driver patches for 5.7-rc1.
Lots of things in here, and it's later than expected due to some
reverts to resolve some reported issues. All is now clean with no
reported problems in linux-next.
Included in here is:
- interconnect updates
- mei driver updates
- uio updates
- nvmem driver updates
- soundwire updates
- binderfs updates
- coresight updates
- habanalabs updates
- mhi new bus type and core
- extcon driver updates
- some Kconfig cleanups
- other small misc driver cleanups and updates
As mentioned, all have been in linux-next for a while, and with the
last two reverts, all is calm and good"
* tag 'char-misc-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (174 commits)
Revert "driver core: platform: Initialize dma_parms for platform devices"
Revert "amba: Initialize dma_parms for amba devices"
amba: Initialize dma_parms for amba devices
driver core: platform: Initialize dma_parms for platform devices
bus: mhi: core: Drop the references to mhi_dev in mhi_destroy_device()
bus: mhi: core: Initialize bhie field in mhi_cntrl for RDDM capture
bus: mhi: core: Add support for reading MHI info from device
misc: rtsx: set correct pcr_ops for rts522A
speakup: misc: Use dynamic minor numbers for speakup devices
mei: me: add cedar fork device ids
coresight: do not use the BIT() macro in the UAPI header
Documentation: provide IBM contacts for embargoed hardware
nvmem: core: remove nvmem_sysfs_get_groups()
nvmem: core: use is_bin_visible for permissions
nvmem: core: use device_register and device_unregister
nvmem: core: add root_only member to nvmem device struct
extcon: axp288: Add wakeup support
extcon: Mark extcon_get_edev_name() function as exported symbol
extcon: palmas: Hide error messages if gpio returns -EPROBE_DEFER
dt-bindings: extcon: usbc-cros-ec: convert extcon-usbc-cros-ec.txt to yaml format
...
Pull crypto updates from Herbert Xu:
"API:
- Fix out-of-sync IVs in self-test for IPsec AEAD algorithms
Algorithms:
- Use formally verified implementation of x86/curve25519
Drivers:
- Enhance hwrng support in caam
- Use crypto_engine for skcipher/aead/rsa/hash in caam
- Add Xilinx AES driver
- Add uacce driver
- Register zip engine to uacce in hisilicon
- Add support for OCTEON TX CPT engine in marvell"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (162 commits)
crypto: af_alg - bool type cosmetics
crypto: arm[64]/poly1305 - add artifact to .gitignore files
crypto: caam - limit single JD RNG output to maximum of 16 bytes
crypto: caam - enable prediction resistance in HRWNG
bus: fsl-mc: add api to retrieve mc version
crypto: caam - invalidate entropy register during RNG initialization
crypto: caam - check if RNG job failed
crypto: caam - simplify RNG implementation
crypto: caam - drop global context pointer and init_done
crypto: caam - use struct hwrng's .init for initialization
crypto: caam - allocate RNG instantiation descriptor with GFP_DMA
crypto: ccree - remove duplicated include from cc_aead.c
crypto: chelsio - remove set but not used variable 'adap'
crypto: marvell - enable OcteonTX cpt options for build
crypto: marvell - add the Virtual Function driver for CPT
crypto: marvell - add support for OCTEON TX CPT engine
crypto: marvell - create common Kconfig and Makefile for Marvell
crypto: arm/neon - memzero_explicit aes-cbc key
crypto: bcm - Use scnprintf() for avoiding potential buffer overflow
crypto: atmel-i2c - Fix wakeup fail
...
Add a new api that returns Management Complex firmware version
and make the required structure public. The api's first user will be
the caam driver for setting prediction resistance bits.
Signed-off-by: Andrei Botila <andrei.botila@nxp.com>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Horia Geantă <horia.geanta@nxp.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Iuliana Prodan <iuliana.prodan@nxp.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-imx@nxp.com
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For some scenarios like controller suspend and resume, mhi_destroy_device()
will get called without mhi_unregister_controller(). In that case, the
references to the mhi_dev created for the channels will not be dropped
but the channels will be destroyed as per the spec. This will cause issue
during resume as the channels will not be created due to the fact that
mhi_dev is not NULL.
Hence, this change decrements the refcount for mhi_dev in
mhi_destroy_device() for concerned channels and also sets mhi_dev to NULL
in release_device().
Reported-by: Carl Huang <cjhuang@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200324061050.14845-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bhie field in mhi_cntrl needs to be initialized to proper register
base in order to make mhi_rddm_prepare() to work. Otherwise,
mhi_rddm_prepare() will cause NULL pointer dereference.
Fixes: 6fdfdd2732 ("bus: mhi: core: Add support for downloading RDDM image during panic")
Reported-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200324061050.14845-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MHI register base has several registers used for getting the MHI
specific information such as version, family, major, and minor numbers
from the device. This information can be used by the controller drivers
for usecases such as applying quirks for a specific revision etc...
While at it, let's also rearrange the local variables
in mhi_register_controller().
Suggested-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200324061050.14845-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just merge in a ti-sysc fix for am335x lcdc suspend/resume issue, and
resolve merge conflict.
-----BEGIN PGP SIGNATURE-----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=k3V/
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.7/ti-sysc-fix-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/drivers
Fix for ti-sysc suspend/resume issue on am335x for v5.7 merge window
Just merge in a ti-sysc fix for am335x lcdc suspend/resume issue, and
resolve merge conflict.
* tag 'omap-for-v5.7/ti-sysc-fix-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Fix quirk flags for lcdc on am335x
Link: https://lore.kernel.org/r/pull-1584132028-918607@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Few more fixes for omaps
Just few dts fixes:
- A fix droid4 touchscreen stopping working with lost gpio interrupts
- Also limit omap5 dma range similar to what we've recently done for dra7
* tag 'omap-for-v5.6/fixes-rc6-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap5: Add bus_dma_limit for L3 bus
ARM: dts: omap4-droid4: Fix lost touchscreen interrupts
ARM: dts: dra7: Add bus_dma_limit for L3 bus
ARM: dts: N900: fix onenand timings
ARM: dts: Fix dm814x Ethernet by changing to use rgmii-id mode
Link: https://lore.kernel.org/r/pull-1584575254-461940@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A pretty normal set of fixes for v5.6:
- Fix reversed macros used for A83T EMAC clock and reset
- Fix camera regulator voltage and USB OTG for TBS-A711
- 16-bit / 8-bit mixed read fix for our RSB driver
- Fix SPI controller base address for R40
- Reorder device nodes based on base address for R40
-----BEGIN PGP SIGNATURE-----
iQJCBAABCgAsFiEE2nN1m/hhnkhOWjtHOJpUIZwPJDAFAl5rGFcOHHdlbnNAY3Np
ZS5vcmcACgkQOJpUIZwPJDC7ehAAjd+M6e4/XPSJvR6w5EOSbbZ7lJbW916+I4TK
vFvwyow4YQX7ryE6ivq0ytGYA2THJQI8TSxhaeLUVNF64TnG6LzsXIyyqPRVyav+
AxIB2tQWWnemcVPfS1CobRF3FXng1hBzs2ooaGb3N9ois1wcVTqHvcOxkvaNvZ3s
0q8tIAmvnkBiqBESdcwz3hjYZqhcbkj3qra73xJVy7BmwOhsBquEYbeCmO2eyqdO
FjhWpE5BuR/4D3UZYrVnhz+r+6LSWlM/Bc8MfAOmtFHrYJkcFLF5CYqctGzPyjkS
sPWtmHKszJfep7u8PHVvEsM7T9EXjtj/B2/z3ms0Z8YnWiEMkBB9qfc9dnvdy0QI
TAod6n4i2r2Jf8lFVSnDYEGBa2+vD3D6ySG5vAi4PzkErF+eO9Av3t/JUeco2uWY
uD7UROyK+34kxPcn+RYkcudnTqPyAmSiAPE9xBOM9qIzaEXk9bwrdI4bA+LVtoYX
y2/c1MC3j4iM+7Xa7UxSkclmDi8Pty++wwtTX6g8MAzEhncx52SALa2mmm6LCSNc
Z2zOBy1SFkzi71c11GZCzMu8cV+W6R9wXQ8x2hfqqngPDrXBUgnKy6jpCEzF/NCm
O1JYtwRHslMEsRwR+Co/4Av/Smt20qC1peVjQe93OLWOYTj3YAdLTVR9sd3DLcLd
S4DkeJ0=
=yBY0
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
Allwinner Fixes for v5.6
A pretty normal set of fixes for v5.6:
- Fix reversed macros used for A83T EMAC clock and reset
- Fix camera regulator voltage and USB OTG for TBS-A711
- 16-bit / 8-bit mixed read fix for our RSB driver
- Fix SPI controller base address for R40
- Reorder device nodes based on base address for R40
* tag 'sunxi-fixes-for-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: r40: Move SPI device nodes based on address order
ARM: dts: sun8i: r40: Fix register base address for SPI2 and SPI3
ARM: dts: sun8i: r40: Move AHCI device node based on address order
bus: sunxi-rsb: Return correct data when mixing 16-bit and 8-bit reads
ARM: dts: sun8i-a83t-tbs-a711: Fix USB OTG mode detection
ARM: dts: sun8i-a83t-tbs-a711: HM5065 doesn't like such a high voltage
ARM: dts: sun8i: a83t: Fix incorrect clk and reset macros for EMAC device
Link: https://lore.kernel.org/r/20200313055233.GA19649@wens.csie.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Driver changes for ti-sysc interconnect target module driver mostly
to be able to probe display subsystem (DSS) without platform data:
- Rename clk_enable/disable quirks to less confusing pre and post
reset quirks
- Enable module reset to work with modules with no sysconfig register
- Also consider non-existing module register when matching quirks
- Don't warn with nested ti-sysc devices
- Implement basic SoC revision handling
- Detect DSS related devices
- Implement DSS reset quirks
Note that there is also a DSS driver specific probe fix to allow
probing devices configured for interconnect target module data that
was agreed to be merged along with the ti-sysc driver changes.
And then there also changes to handle RTC, EDMA and PRUSS:
- Add module unlock quirk for RTC
- Detect EDMA modules
- Add support for handling PRUSS
-----BEGIN PGP SIGNATURE-----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=KmZS
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.7/ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/drivers
Driver changes for ti-sysc for v5.7 merge window
Driver changes for ti-sysc interconnect target module driver mostly
to be able to probe display subsystem (DSS) without platform data:
- Rename clk_enable/disable quirks to less confusing pre and post
reset quirks
- Enable module reset to work with modules with no sysconfig register
- Also consider non-existing module register when matching quirks
- Don't warn with nested ti-sysc devices
- Implement basic SoC revision handling
- Detect DSS related devices
- Implement DSS reset quirks
Note that there is also a DSS driver specific probe fix to allow
probing devices configured for interconnect target module data that
was agreed to be merged along with the ti-sysc driver changes.
And then there also changes to handle RTC, EDMA and PRUSS:
- Add module unlock quirk for RTC
- Detect EDMA modules
- Add support for handling PRUSS
* tag 'omap-for-v5.7/ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Add support for PRUSS SYSC type
dt-bindings: bus: ti-sysc: Add support for PRUSS SYSC type
bus: ti-sysc: Detect EDMA and set quirk flags for tptc
bus: ti-sysc: Fix wrong offset for display subsystem reset quirk
bus: ti-sysc: Implement display subsystem reset quirk
bus: ti-sysc: Detect display subsystem related devices
bus: ti-sysc: Handle module unlock quirk needed for some RTC
bus: ti-sysc: Implement SoC revision handling
bus: ti-sysc: Don't warn about legacy property for nested ti-sysc devices
bus: ti-sysc: Consider non-existing registers too when matching quirks
bus: ti-sysc: Improve reset to work with modules with no sysconfig
bus: ti-sysc: Rename clk related quirks to pre_reset and post_reset quirks
bus: ti-sysc: Fix 1-wire reset quirk
drm/omap: Prepare DSS for probing without legacy platform data
Link: https://lore.kernel.org/r/pull-1583511417-919838@atomide.com-3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Fix up the device resources for the broken firmware to avoid
use-after-free warnings from KASAN in the host removal path
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=hIMK
-----END PGP SIGNATURE-----
Merge tag 'hisi-drivers-for-5.7' of git://github.com/hisilicon/linux-hisi into arm/drivers
ARM64: hisi: SoC driver updates for 5.7
- Fix up the device resources for the broken firmware to avoid
use-after-free warnings from KASAN in the host removal path
* tag 'hisi-drivers-for-5.7' of git://github.com/hisilicon/linux-hisi:
bus: hisi_lpc: Fixup IO ports addresses to avoid use-after-free in host removal
Link: https://lore.kernel.org/r/5E61F700.5060301@hisilicon.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The module owner field can be used to prevent the removal of kernel
modules when there are any device files associated with it opened in
userspace. Hence, modify the API to pass module owner field. For
convenience, module_mhi_driver() macro is used which takes care of
passing the module owner through THIS_MODULE of the module of the
driver and also avoiding the use of specifying the default MHI client
driver register/unregister routines.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200324061050.14845-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix printk format warning by using %z for size_t modifier:
../drivers/bus/mhi/core/boot.c: In function `mhi_rddm_prepare':
../drivers/bus/mhi/core/boot.c:55:15: warning: format `%lx' expects argument of type `long unsigned int', but argument 5 has type `size_t {aka unsigned int}' [-Wformat=]
dev_dbg(dev, "Address: %p and len: 0x%lx sequence: %u
",
Link: http://lkml.kernel.org/r/c4852a82-cdb9-6318-70a4-96ccb4ba5af2@infradead.org
Fixes: 6fdfdd2732 ("bus: mhi: core: Add support for downloading RDDM image during panic")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Hemant Kumar <hemantk@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Link: https://lore.kernel.org/r/20200324022505.UiPPJZVXX%akpm@linux-foundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add uevent support to MHI bus so that the client drivers can be autoloaded
by udev when the MHI devices gets created. The client drivers are
expected to provide MODULE_DEVICE_TABLE with the MHI id_table struct so
that the alias can be exported.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-13-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for transferring data between external modem and host
processor using MHI protocol.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/988
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: splitted the data transfer patch and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-12-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for processing the MHI data and control
events from the client device. The client device can report various
events such as EE events, state change events by interrupting the
host through IRQ and adding events to the event rings allocated by
the host during initialization.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/988
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: splitted the data transfer patch and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-11-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MHI protocol supports downloading RDDM (RAM Dump) image from the
device through BHIE. This is useful to debugging as the RDDM image
can capture the firmware state.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/989
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: splitted the data transfer patch and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-10-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MHI supports downloading the device firmware over BHI/BHIe (Boot Host
Interface) protocol. Hence, this commit adds necessary helpers, which
will be called during device power up stage.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/989
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: splitted the data transfer patch and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-9-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for basic MHI PM operations such as
mhi_async_power_up, mhi_sync_power_up, and mhi_power_down. These
routines places the MHI bus into respective power domain states
and calls the state_transition APIs when necessary. The MHI
controller driver is expected to call these PM routines for
MHI powerup and powerdown.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/989
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: splitted the pm patch and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-8-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for transitioning the MHI states as a
part of the power management operations. Helpers functions are
provided for the state transitions, which will be consumed by the
actual power management routines.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/989
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[jhugo: removed dma_zalloc_coherent() and fixed several bugs]
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
[mani: splitted the pm patch and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-7-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for ringing channel and event ring doorbells
by MHI host. The MHI host can use the channel and event ring doorbells
for notifying the client device about processing transfer and event
rings which it has queued using MMIO registers.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/989
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: splitted from pm patch and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-6-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for creating and destroying MHI devices. The
MHI devices binds to the MHI channels and are used to transfer data
between MHI host and client device.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/989
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: splitted from pm patch and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for registering MHI client drivers with the
MHI stack. MHI client drivers binds to one or more MHI devices inorder
to sends and receive the upper-layer protocol packets like IP packets,
modem control messages, and diagnostics messages over MHI bus.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/987
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: splitted and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for registering MHI controller drivers with
the MHI stack. MHI controller drivers manages the interaction with the
MHI client devices such as the external modems and WiFi chipsets. They
are also the MHI bus master in charge of managing the physical link
between the host and client device.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/987
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[jhugo: added static config for controllers and fixed several bugs]
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
[mani: removed DT dependency, splitted and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200220095854.4804-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit adb72394e2 ("ARM: OMAP2+: Drop legacy platform data for am3
lcdc") dropped legacy platform data but we never added the quirks for
SWSUP_SIDLE and SWSUP_MSTANDBY for lcdc for ti-sysc driver.
This breaks suspend/resume. Let's fix the issue by enabling the same
quirks for ti-sysc driver as we had earlier with platform data.
Fixes: adb72394e2 ("ARM: OMAP2+: Drop legacy platform data for am3 lcdc")
Fixes: 23731eac98 ("bus: ti-sysc: Detect devices on am335x when DEBUG is enabled")
Reported-by: Keerthy <j-keerthy@ti.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Tested-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The PRU-ICSS present on AM33xx/AM43xx/AM57xx has a very unique
SYSCFG register. The register follows the OMAP4-style SYSC_TYPE3
for Master Standby and Slave Idle, but also has two additional
unique fields - STANDBY_INIT and SUB_MWAIT. The STANDBY_INIT is
a control bit that is used to initiate a Standby sequence (when
set) and trigger a MStandby request to the SoC's PRCM module. This
same bit is also used to enable the OCP master ports (when cleared)
to allow the PRU cores to access any peripherals or memory beyond
the PRU subsystem. The SUB_MWAIT is a ready status field for the
external access.
Add support for this SYSC type. The STANDBY_INIT has to be set
during suspend, without which it results in a hang in the resume
sequence on AM33xx/AM43xx boards and requires a board reset to
come out of the hang. Any PRU applications requiring external
access are supposed to clear the STANDBY_INIT bit. Note that
the PRUSS context is lost during a suspend sequence because the
PRUSS module is reset and/or disabled.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
[tony@atomide.com: updated quirk define number and to use -ENODEV]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Jeffrey Hugo