For accessing PCIe ctrl memory we depend on the BAR aperture being
large enough to reach all registers. Since the BAR aperture can
be set in the flash make sure the driver won't oops the kernel
when the PCIe configuration is unusual.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ioremap of PCIe ctrl memory failed we can still get to it through
PCI config space, therefore we allow ioremap() to fail. When if fails,
however, we must leave all the IOMEM pointers as NULL. Currently we
would calculate csr and em pointers, adding offsets to the potential
NULL value and therefore making the NULL-checks throughout the code
ineffective.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI subsystem has support for drivers limiting the number of VFs
available below what the IOV capability claims. Make use of it.
While at it remove the #ifdef/#endif on CONFIG_PCI_IOV, it was
there to avoid unnecessary warnings in case device read failed
but kernel doesn't have SR-IOV support anyway. Device reads
should not fail.
Note that we still need the driver-internal check for the case
where max VFs is 0 since PCI subsystem treats 0 as limit not set.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose FW app ability to change MAC address at runtime. Make sure
we only depend on it if FW app advertised the right capability.
Signed-off-by: Pablo Cascón <pablo.cascon@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring port split with devlink. Add devlink
callbacks to validate requested config and call NSP helpers.
Getting the right nfp_port structure can be done with simple iteration.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For port splitting we will need to know the total number of lanes
in a port. Calculate that based on eth_table information.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend nfp_port to contain devlink_port structures. Register the
ports to allow users inspecting device ports.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will soon have to invoke more clean up for vNICs.
Move the cleanup callbacks into a helper.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add initial devlink support. This patch simply switches allocation
of per-adapter structure to devlink's priv and register devlink
with empty ops table. See following patches for implementation
of particular ops.
We should now clear the app pointer on exit, this is how devlink
callbacks will know app is not initialized.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move mutex init to main file close to structure allocation.
This will allow mutex to be taken before net code runs (e.g.
from devlink callbacks). While at it remember to destroy
the mutex.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
State of autonegotiation may have changed but is not yet refreshed.
Make sure ethtool respects the NFP_PORT_CHANGED flag when looking
at autoneg.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If reading new state of the port failed, mark the port back as CHANGED.
This way next user state request will trigger refresh, which will
hopefully succeed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After port configuration is performed mark it as changed. This
will close a window of time between configuration and async
state refresh which runs from a workqueue where old port state
would be reported.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add link to nfp_ports to make it possible to iterate over all ports.
This will come in handy when some ports may be representors.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Track whether physical port's state have changed since last refresh
inside the nfp_port structure instead of the vNIC structure.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always updating port state in place by overriding values in exiting
pf->eth_tbl makes things easier to manage and allows us to have a
common helper for both full and per-port refresh.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Encapsulate port information into struct nfp_port. nfp_port will
soon be extended to contain devlink_port information. It also makes
it easier to reuse port-related code between vNICs and representors.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only support core NIC apps which have vNICs for each physical port/
split and no representors right now. Enforce that either each vNIC has
a NSP eth_table entry or if NSP port table is not available none do.
One scenario this will prevent from happening is user force-loading
wrong firmware file if FW app requires different firmwares per media
config.
While at it move some code to nfp_net_pf_alloc_vnic() to make it
counter-match nfp_net_pf_free_vnic() better.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a concept of an application. For now it's just grouping
pointers and serving as a layer of indirection. It will help us
weaken the dependency on nfp_net in ethtool code. Later series
will flesh out support for different apps in the driver.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Soon a third place will need to free a struct nfp_net. Add a free
counterpart to nfp_net_pf_alloc_vnic().
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vNIC is a PCIe-side abstraction NFP firmwares supported by this
driver use. It was initially meant to represent a device port
and therefore a netdev but today should be thought of as a way
of grouping descriptor rings and associated state. Advanced apps
will have vNICs without netdevs and ports without a vNIC (using
representors instead).
Make sure code refers to vNICs as vNICs and not ports or netdevs.
No functional changes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct nfp_net represents a vNIC, we will be moving away from the
requirement for every vNIC to have a netdev associated with it.
Remove "netdev" from some function names and prefer passing
struct nfp_net pointer as argument instead of struct net_device *.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add nfp_cppcore_pcie_unit() helper to retrieve the PCIE unit of a CPP
handle and use the new helper as appropriate.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Given that our rings are always a power of 2, we can simplify the
calculation of number of completed TX descriptors by using masking
instead of if statement based on whether the index have wrapped
or not.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a number of places where we calculate the descriptor
index based on a value which may have overflown. Create a
macro for masking with the ring size.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since XDP TX ring holds "spare" RX buffers anyway, we don't have to
rush the completion. We can wait until ring fills up completely
before trying to reclaim buffers. If RX poll has ended an no
buffer has been queued for XDP TX we have no guarantee we will see
another interrupt, so run the reclaim there as well, to make sure
TX statistics won't become stale.
This should help us reclaim more buffers per single queue controller
register read.
Note that the XDP completion is very trivial, it only adds up
the sizes of transmitted frames for statistics so the latency
spike should be acceptable. In case user sets the ring sizes
to something crazy, limit the completion to 2k entries.
The check if the ring is empty at the beginning of xdp_complete()
is no longer needed - the callers will perform it.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce NFP_NET_CFG_CTRL_CSUM_COMPLETE capability and implement parsing
of CHECKSUM_COMPLETE metadata.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Edwin Peer <edwin.peer@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ABI version 4 introduced metadata chaining. Using the ABI version to signal
metadata chaining precludes firmware that advertises new capabilities which
rely on prepended metadata from working on older kernels.
Capability bits are thus better suited to signalling the chained metadata
format. A new version of the RSS capability is introduced to distinguish
between the differing metadata formats for ABI versions other than 4.
Signed-off-by: Edwin Peer <edwin.peer@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if capability for RSS and IRQ moderation are present we may
have not initialized them for control vNIC. Depend on selected
features mask (ctrl) rather than capabilities (cap) to determine
which features should be enabled.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware advertising the LSO2 capability exploits driver provided L3 and L4
offsets in order to avoid parsing packet headers in the TX path. The vlan
field in struct nfp_net_tx_desc is repurposed, making TXVLAN a mutually
exclusive configuration to LSO2.
Signed-off-by: Edwin Peer <edwin.peer@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The l4_offset field referred to by NFD is confusingly named. It is not the
offset of the L4 transport header, but rather the L4 payload.
The LSO2 capability supported by alternative device firmware requires
the actual L4 offset, thus the rename seems prudent.
Signed-off-by: Edwin Peer <edwin.peer@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We advertise TSO to the stack but leave it disabled by default.
Make sure it's not only disabled in the netdev features but
also on the device itself.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Small follow-up to d74a32acd5 ("xdp: use netlink extended ACK reporting")
in order to let drivers all use the same NL_SET_ERR_MSG_MOD() helper macro
for reporting. This also ensures that we consistently add the driver's
prefix for dumping the report in user space to indicate that the error
message is driver specific and not coming from core code. Furthermore,
NL_SET_ERR_MSG_MOD() now reuses NL_SET_ERR_MSG() and thus makes all macros
check the pointer as suggested.
References: https://www.spinics.net/lists/netdev/msg433267.html
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Try to carry error messages to the user via the netlink extended
ack message attribute.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
For legacy reasons NFP FW may be compiled to DMA packets to a constant
offset into the buffer and use the space before it for metadata. This
ensures that packets data always start at a certain offset regardless of
the amount of preceding metadata.
If rx offset is set to 0 there may still be up to 64 bytes of metadata
but metadata will start at the beginning of the buffer, instead of:
data_start_offset = rx_offset - meta_len
Even though we make the buffers larger to accommodate up to 64 bytes of
metadata, if there is only N bytes of metadata, we will end up with
N bytes of headroom and 64 - N bytes of tailroom. Therefore we can't
rely on that space for XDP headroom. Make sure we always allocate
full 256 bytes. This, unfortunately, means we can't fit the headroom
on an u8 any more.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now the required Service Process ABI version is still tied
to max ID of known commands. For new NSP commands we are adding
we are checking if NSP version is recent enough on command-by-command
basis. The driver doesn't have to force the device to have the
very latest flash, anything newer than 0.8 should do.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reading TX queue indexes from the device memory on each interrupt
is expensive. It's doubly expensive with XDP running since we have
two TX rings to check there. If the software indexes indicate that
the TX queue is completely empty, however, we don't need to look at
the device completion index at all.
The queuing CPU is doing a wmb() before kicking the device TX so
we should be safe to assume on the CPU handling the completions will
never see old value of the software copy of the index.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the RX path we follow the "drop if allocation of replacement
buffer fails" rule. With XDP we extended that to the TX action,
so if XDP prog returned TX but allocation of replacement RX buffer
failed, we will drop the packet.
To improve our XDP TX performance extend the idea of rings being
always full to XDP TX rings. Pre-fill the XDP TX rings with RX
buffers, and when XDP prog returns TX action swap the RX buffer
with the next buffer from the TX ring.
XDP TX complete will no longer free the buffers but let them
sit on the TX ring and wait for swap with RX buffer, instead.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will soon allocate RX buffers for caching on XDP TX rings.
The rx_ring parameter passed to nfp_net_rx_alloc_one() is not
actually used, remove it.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Or points out in commit 423b3aecf2 ("net/mlx4: Change ENOTSUPP
to EOPNOTSUPP"), ENOTSUPP is NFS specific error. Replace it with
EOPNOTSUPP.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code refreshing the eth port state was trying to update state
of all ports of the card. Unfortunately to safely walk the port
list we would have to hold the port lock, which we can't due to
lock ordering constraints against rtnl.
Make the per-port sync refresh and async refresh of all ports
completely separate routines.
Fixes: 172f638c93 ("nfp: add port state refresh")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XDP headroom should not be included in free list buffer size.
Fixes: 6fe0c3b438 ("nfp: add support for xdp_adjust_head()")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Retrieve identifying information from the NSP. For now it only
contains versions of firmware subcomponents.
Signed-off-by: David Brunecz <david.brunecz@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling memcpy to shift metadata out of the way for XDP to run
seems like an overkill. The most common metadata contents are
8 bytes containing type and flow hash. Simply parse the metadata
before we run XDP.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA unmap may destroy changes CPU made to the buffer. To make XDP
run correctly on non-x86 platforms we should use the
DMA_ATTR_SKIP_CPU_SYNC attribute.
Thanks to using the attribute we can now push the sync operation to the
common code path from XDP handler.
A little bit of variable name reshuffling is required to bring the
code back to readable state.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the case where nn->eth_port is null the warning message
is printing the port by dereferencing this null pointer.
Remove the deference to avoid a crash when printing the
warning message.
Detected by CoverityScan, CID#1426198 ("Dereference after null check")
Fixes: ce22f5a2cb ("nfp: separate high level and low level NSP headers")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly simple cases of overlapping changes (adding code nearby,
a function whose name changes, for example).
Signed-off-by: David S. Miller <davem@davemloft.net>
We should unregister the net_device first, before we give back
our reference on xdp_prog. Otherwise xdp_prog may be freed
before .ndo_stop() disabled the datapath. Found by code inspection.
Fixes: ecd63a0217 ("nfp: add XDP support in the driver")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support setting link speed and autonegotiation through
set_link_ksettings() ethtool op. If the port is reconfigured
in incompatible way and reboot is required the netdev will get
unregistered and not come back until user reboots the system.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add NSP backend for upcoming link configuration operations.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow NSP to set option code even when error is reported. This provides
a way for NSP to give user more precise information about why command
failed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make NSP port structure a union to simplify accessing the fields
from generic macros.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NSP commands may be slow to respond, we should try to avoid doing
a command-per-item when user requested to change multiple parameters
for instance with an ethtool .set_settings() command.
Introduce a way of internal NSP code to carry state in NSP structure
and add start/finish calls to perform the initialization and kick off
of the configuration request, with potentially many parameters being
modified in between.
nfp_eth_set_mod_enable() will make use of the new code internally,
other "set" functions to follow.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will soon add more NSP commands and structure definitions.
Move all high-level NSP header contents to a common nfp_nsp.h file.
Right now it mostly boils down to renaming nfp_nsp_eth.h and
moving some functions from nfp.h there.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Service process firmware provides us with information about media
and interface (SFP module) plugged in, translate that to Linux's
PORT_* defines and report via ethtool.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NSP ABI version 0.17 is exposing the autonegotiation settings.
Report whether autoneg is on via ethtool.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the PF prefer the link speed value provided by the NSP.
Refresh port table if needed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will need a way of refreshing port state for link settings
get/set. For get we need to refresh port speed and type.
When settings are changed the reconfiguration may require
reboot before it's effective. Unregister netdevs affected
by reconfiguration from a workqueue.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For caching link settings - remember if we have seen link events
since the last time the eth_port information was refreshed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will want to unregister netdevs after their port got reconfigured.
For that we need to make sure manipulations of port list from the
port reconfiguration flow will not race with driver's .remove()
callback.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After port reconfiguration (port split, media type change)
firmware will continue to report old configuration until
reboot. NSP will inform us that reconfiguration is pending.
To avoid user confusion refuse to spawn netdevs until the
new configuration is applied (reboot).
We need to split the netdev to eth_table port matching from
MAC search and move it earlier in the probe() flow.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read link speed from the BAR. This provides very basic information
and works for both PFs and VFs.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we no longer need to keep the FW enabled for .ndo_close()
to work we can always stop FW after reconfiguration failure.
This seems to make most FWs more resilient to faults (at least
in error injection scenarios).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device open and close handlers check if the device is already
in the desired state. Thanks to our reconfig infrastructure
this should not be necessary, there doesn't seem to be any
code in the driver which depends on it.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of ring full or DMA mapping error remember to flush xmit_more
delayed kicks.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFP6000 doesn't use queue pointers/doorbells for RX, it uses
'done' bit in descriptors. Remove the pointers from data structures.
Since we are saving space in rx_ring structure make fields we
previously compressed to 16bits word size again.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix warning which was using netdev_warn() instead of dev_warn()
to early.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When acquiring an area fails we can't call function doing both
release and free.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Core should detect when someone is trying to request an access
window which is too large for a given type of access. Otherwise
the requester will be put on a wait queue for ever without any
error message.
Add const qualifiers to clarify that we are only looking at read-
-only members in relevant functions.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When signal interrupts waiting for an area to become available
we assume success. Pay attention to the return code. Unpack
the code a little bit to make it more readable.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
msleep_interruptible() returns time left to wait, not error
code. Return ERESTARTSYS when interrupted.
While at it correct a comment and make the polling a bit
more aggressive.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We shouldn't access area_cache_list without its lock even
to check if it's empty.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document which fields of nfp_cpp are protected by which locks.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After mutex cache removal we can put the mutex code in a separate
source file. This makes it clear it doesn't play with internals
of struct nfp_cpp any more.
No functional changes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPP mutex cache was introduced to work around the fact that the
same host could successfully acquire a lock multiple times. It
used to collapse multiple users to the same struct nfp_cpp_mutex
and track use count. Unfortunately it's racy. Since we now force
all nfp_mutex_lock() callers within the host to actually succeed
at acquiring the lock we no longer need the cache, let's remove it.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The global device lock is acquired to search the resource table.
The lock is actually itself part of the table (entry 0).
Therefore if someone asks for resource 0 we would deadlock since
double locking is no longer allowed.
Currently the driver doesn't try to lock that resource so let's
simply make sure we fail graciously and not add special handling
of this case until really need. Hide the relevant defines in
the source file.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFP can be connected to multiple machines via PCI or other buses.
Access to hardware resources is arbitrated using locks residing
in device memory. Currently nfpcore only respects the mutexes
when it comes to inter-host locking, but if we try to acquire
the same lock again, on one host - it will simply return success
because owner of the lock is already set to that host.
This makes the locks useless for arbitration within one host
and unfair because whichever host grabbed the lock will have
a chance to reacquire it without others getting a shot.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support prepending data from XDP. We are already always allocating
some headroom because FW may prepend metadata to packets.
xdp_adjust_head() can be supported by making sure that headroom is
big enough for XDP. In case FW had prepended metadata to the packet,
however, we have to move it out of the way before we call XDP.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XDP may require us to move metadata to make room for pushing
headers. Track meta data location with a pointer and pass
it explicitly to functions.
While at it validate that meta_len from the descriptor is not
bogus.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename pkt_off variable to dma_off, it should hold data offset
counting from beginning of DMA mapping. Compute the value only
in XDP context.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFP_NET_CFG_RX_OFFSET is 32bit wide, make sure what we read from
there is reasonable for packet headroom. This allows us to store
the rx_offset in a 8bit variable.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of testing if xdp_prog is present store the dma direction
in data path structure.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of passing around sets of rings and their parameters just
store all information in the data path structure.
We will no longer user xchg() on XDP programs when we swap programs
while the traffic is guaranteed not to be flowing. This allows us
to simply assign the entire data path structures instead of copying
field by field.
The optimization to reallocate only the rings on the side (RX/TX)
which has been changed is also removed since it seems like it's not
worth the code complexity.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use xdp_prog member of data path struct to carry the xdp_prog to
alloc/free free functions.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the mtu member from ring set to data path struct.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use fl_bufsz member of data path struct to carry desired size of
free list entries.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of passing variables around use dp to store number of tx rings
for the stack and number of IRQ vectors.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make callers of nfp_net_ring_reconfig() pass newly allocated data
path structure. We will gradually make use of that structure
instead of passing parameters around to all the allocation functions.
This commit adds allocation and propagation of new data path struct,
no parameters are converted, yet.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Control BAR pointer is used to unmask interrupts so it should be
in the first cacheline of adapter structure.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all data path information into a separate structure. This way
we will be able to allocate new data path with all new rings etc.
and swap it in easily.
No functional changes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent theoretical buffer overrun by returning an error if
the number of entries returned by the firmware does not match those
present.
Also use a common handling error path.
Found by inspection.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Tested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only need FW version in the first cache line of adapter struct
because we need to know the metadata format. To save space add a
metadata format bit.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of return code from napi_complete_done() to avoid rearming
interrupts when busy polling is on.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We really only need the device pointer on the fast path, stash it at
the beginning of the adapter structure and move pci_dev pointer down.
This saves up a few lines of code.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reorder variables longest to shortest to comply with netdev coding style.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already print most of ring configuration including descriptors
in debugfs, add the few missing pieces and remove debug prints.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NSP reports to us port labels. First id is the id of the physical
port, the other one tells us which logical interface is it within a
split port. Instead of printing them as string keep them in integer
format. Compute which interfaces are part of port split.
On netdev side use port labels and split information to provide a
.ndo_get_phys_port_name() implementation. We follow the name format
of mlxsw which is also suggested in "Port Netdev Naming" section
of Documentation/networking/switchdev.txt.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some firmware images may reuse CRC32 hardware to compute RXHASH.
Make sure we report the correct hash function. Note that we don't
support changing functions at runtime. That would also require
a few more additions to the way the key is set because different
functions have different key sizes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dma_sync_single_for_*() takes the direction in which the buffer
was mapped, not the direction of the sync. We should sync XDP
buffers bidirectionally.
Fixes: ecd63a0217 ("nfp: add XDP support in the driver")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit c0f031bc88 ("nfp_net: use alloc_frag() and build_skb()")
we are allocating buffers which have to hold both the data and skb to
be created in place by build_skb().
FW should only be told about the buffer space it can DMA to, that
is without the build_skb() headroom and tailroom. Note: firmware
applications should validate the buffers against both MTU and
free list buffer size so oversized packets would not pass through
the NIC anyway.
Fixes: c0f031bc88 ("nfp: use alloc_frag() and build_skb()")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski