This patch increases periods_min to 6 from 4, this will remove any
hickups where the buffer is not filled fast enough from user space.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch replaces the references to bus_id to the new dev_name() API.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch replaces the references to bus_id to the new dev_name() API.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch will set the channel A and control channel mode register to
zero before disabling the AC97C peripheral.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch will enable the AC97C before resetting the external codec,
leaving the AC97C disabled will result in floating I/O lines that can
affect the reset procedure.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch will enable interrupts from AC97C and report about error
conditions that occurs.
On channel A both overrun and underrun will be enabled depending if
playback and/or capture are enabled. On the control channel the overrun
interrupt is enabled.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch will set a proper maximum bytes for the buffer, which is:
channels * bytes per sample * maximum periods * maximum bytes per period.
It also sets the minimum periods to 6, a value chosen from testing, with
a minimum of 6 periods the system has good time to fill in new audio
data without skipping.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch will take care not to overwrite OCA and ICA registers when
assigning input and output channels. It will also make sure the
registers are at a known state when enabling a channel and clean up
properly in case of an error.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch will remove traces of channel B registers, since they are not
used by the AC97C driver. Channel B might be used for other purposes.
The driver also adds channel status bits TXEMPTY and OVRUN and a
AC97C_CH_MASK macro to ease clearing a channel settings.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds ALSA support for the AC97 controller found on Atmel
AVR32 devices.
Tested on ATSTK1006 + ATSTK1000 with a development board with a AC97
codec.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds ALSA support for the Audio Bistream DAC found on Atmel
AVR32 devices. The ABDAC is an Atmel IP which might show up on AT91
devices in the future, hence making a generic driver which can be
utilized by AT91 arch if needed.
Datasheet describing the ABDAC peripheral is available in the AT32AP7000
datasheet, http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
Tested on ATSTK1006 + ATSTK1000 with a class D amplifier stage.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Hans-Christian Egtvedt