While running the kms_plane clipping test I noticed a similar problem to
the one described in Display WA #1175. In this case, similarly for
planes other than the cursor, with 1 or 3 pixels visible from the left
edge of the screen to the end of the plane and an odd plane X offset
used for clipping causes the same kind of underflow and display
corruption as described for WA #1175. Fix this in a similar way as that
WA rejecting planes ending <4 pixels from the left screen edge.
v2:
- Rebase on v2 of patch 1/1.
Testcase: igt/kms_plane/plane-clipping-pipe-*-planes
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180116112415.22060-2-imre.deak@intel.com
As described in the WA on GLK and CNL planes on the right edge of the
screen that have less than 4 pixels visible from the beginning of the
plane to the edge of the screen can cause FIFO underflow and display
corruption.
On GLK/CNL I could trigger the problem only if the plane was at the same
time also aligned to the top edge of the screen (after clipping) and
there were exactly 2 pixels visible from the start of the plane to the
right edge of the screen (so couldn't trigger it with 1 or 3 pixels
visible). Nevertheless, to be sure, I also applied the WA for these cases.
I also couldn't see any problem with the cursor plane and later Art
confirmed that it's not affected, so the WA is applied only for the
other plane types.
v2:
- Use -ERANGE instead of -EINVAL. (Chris)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180116112415.22060-1-imre.deak@intel.com
If the table result is out of bounds on the array map
there is something really wrong with VBT pin so we don't
return that vbt_pin, but only return 0 instead.
This basically reverts commit 'a8e6f3888b05 ("drm/i915/cnp:
Ignore VBT request for know invalid DDC pin.")'
Also this properly fixes commit 9c3b2689d0 ("drm/i915/cnl:
Map VBT DDC Pin to BSpec DDC Pin.")
v2: Do in a way that we don't break other platforms. (Jani)
v3: Keep debug message (Jani)
v4: Don't mess with 0 mapping was noticed by Jani and
addressed with a simple solution suggested by Lucas
that makes this even simpler.
Fixes: a8e6f3888b ("drm/i915/cnp: Ignore VBT request for know invalid DDC pin.")
Fixes: 9c3b2689d0 ("drm/i915/cnl: Map VBT DDC Pin to BSpec DDC Pin.")
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Kai Heng Feng <kai.heng.feng@canonical.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Suggested-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180125222524.22059-1-rodrigo.vivi@intel.com
We never support certain mode flags etc. Reject those early on in the
mode_config.mode_valid() hook. That allows us to remove some duplicated
checks from the connector .mode_valid() hooks, and it guarantees that
we never see those flags even from user mode as the
mode_config.mode_valid() hooks gets executed for those as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171114183258.16976-11-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Assert that we do not try to unsubmit a completed request, as should we
try to resubmit it later, the ring is already past the request's
breadcrumb and the breadcrumb will not be updated.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129094912.14428-1-chris@chris-wilson.co.uk
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Older gcc is complaining it can't follow the guards and thinks that
addr may be used uninitialised
In the process, we can simplify down to one loop,
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-131 (-131)
Function old new delta
setup_scratch_page 545 414 -131
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129102840.19901-1-chris@chris-wilson.co.uk
Remove the WARN_ON(ce->state) inside the static function only called
when ce->state == NULL and downgrade the w/a batch setup warning into a
developer only mode (GEM_WARN_ON).
v2: Move the deferred alloc guard into the callee, eliminating the need
for the WARN_ON:
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-1 (-1)
Function old new delta
execlists_context_pin 1819 1818 -1
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180126121846.12007-1-chris@chris-wilson.co.uk
CTX_CONTEXT_CONTROL (CTX_SR_CTL) operates as a masked register and so
will only apply the bits that are selected by the upper half. In the
case of selectively enabling sr inhibit, this may mean the context keeps
the current setting (so forgetting to save the context later, eventually
leading to a very upset GPU!).
Fixes: 517aaffe0c ("drm/i915/execlists: Inhibit context save/restore for the fake preempt context")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180125112443.12745-1-chris@chris-wilson.co.uk
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Use consistent multi-line comment style as per guideline.
v2: Reverted comments prefix update to kernel-doc comment. (Chris)
Suggested-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1516808821-3638-5-git-send-email-sagar.a.kamble@intel.com
i915_guc_log_control is GuC interface and GuC APIs that are not user
facing should be named with "intel_guc" prefix hence we change name to
intel_guc_log_control. Also changed the parameter to intel_guc struct.
v2: Move log vma check to intel_guc_log_control (Michal)
Return -ENODEV when log isn't initialized. (Chris)
Suggested-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1516808821-3638-4-git-send-email-sagar.a.kamble@intel.com
GuC log streaming needs interrupts enabled prior to GuC resume but
runtime pm interrupt setup was happening post GuC resume. Fix it.
While at it, fix the unwinding of steps in the runtime suspend path.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104695
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Marta Lofstedt <marta.lofstedt@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1516808821-3638-2-git-send-email-sagar.a.kamble@intel.com
Disabling GuC interrupts involves access to GuC IRQ control registers
hence ensure device is RPM awake.
v1-v2: old changelog
1: Add comment about need to synchronize flush work and log runtime
destroy
2: Moved patch earlier in the series and removed comment about future
work. (Tvrtko)
v3: Added assert_rpm_wakelock_held() to gen9_*_guc_interrupts. (Chris)
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1516808821-3638-1-git-send-email-sagar.a.kamble@intel.com
Let's document why we claim hsub==8,vsub==16 for CCS.
v2: Replace my explanation with Jason's
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Daniel Stone <daniels@collabora.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180119144152.17224-1-ville.syrjala@linux.intel.com
Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
Apparently SKL/KBL/CFL need some manual help to get the
programmed HDMI vswing to stick. Implement the relevant
workaround (display w/a #1143).
Note that the relevant chicken bits live in a transcoder register
even though the bits affect a specific DDI port rather than a
specific transcoder. Hence we must pick the correct transcoder
register instance based on the port rather than based on the
cpu_transcoder.
Also note that for completeness I included support for DDI A/E
in the code even though we never have HDMI on those ports.
v2: CFL needs the w/a as well (Rodrigo and Art)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180122174131.28046-1-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Replace the ad-hoc plane indexing scheme used by the frontbuffer
tracking with enum plane_id.
The old video overlay not being part of the plane_id namespace
will just be given the high bit.
v2: Drop the unintended whitespace change (Chris)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180123183343.9181-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
When we finally decide the gpu is idle, that is a good time to shrink
our kmem_caches.
v3: Defer until an rcu grace period after we idle.
v4: Think about epoch wraparound and how likely that is.
v5: Use I915_EPOCH_INVALID magic.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180124113608.14909-2-chris@chris-wilson.co.uk
By counting the number of times we have woken up, we have a very simple
means of defining an epoch, which will come in handy if we want to
perform deferred tasks at the end of an epoch (i.e. while we are going
to sleep) without imposing on the next activity cycle.
v2: No reason to specify precise number of bits here.
v3: Take Tvrtko's advice and reserve 0 as an invalid epoch.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180124113608.14909-1-chris@chris-wilson.co.uk
We only use the preempt context to inject an idle point into execlists.
We never need to reference its logical state, so tell the GPU never to
load it or save it.
v2: BIT(2) for save-inhibit.
N.B. Daniele mentioned this bit mbz for ICL, and has been moved into the
submission process rather than the context image.
Suggested-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180123210412.17653-1-chris@chris-wilson.co.uk
Newer platforms may have subtle offset changes, which will increase the
number of defines, so it is probably better to start moving them to its
own header file. Also move the macros used while setting the reg state.
v2: Rename to intel_lrc_reg.h, to be consistent with i915_reg.h and
intel_guc_reg.h (Chris)
v3: License notice shenanigans.
v4: Documentation/process/coding-style.rst is always right (Chris)
v5: Rebase.
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180124004349.22126-2-michel.thierry@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The macros we use to init the reg_state had the following issues reported
by checkpatch --strict.
Macro argument reuse 'reg_state' - possible side-effects
Macro argument reuse 'pos' - possible side-effects
Macro argument reuse 'ppgtt' - possible side-effects
spaces preferred around that '+' (ctx:VxV)
So fix these issues before they are moved to a new header file.
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180124004349.22126-1-michel.thierry@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We need to generate the event config value using the uAPI class and not
the driver internal one.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: 109ec55837 ("drm/i915/pmu: Only enumerate available counters in sysfs")
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180123134558.3222-1-tvrtko.ursulin@linux.intel.com
Current code always select _CNL_AUX_ANAOVRD1_B
register regardless the pw in use.
CNL_DISP_PW_AUX_B = 9
CNL_DISP_PW_AUX_C = 10
CNL_DISP_PW_AUX_D = 11
And for pick we want
B = 0
C = 1
D = 2
Fixes: ddd39e4b3f ("drm/i915/cnl: apply Display WA #1178 to fix type C dongles")
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180123215245.24026-1-rodrigo.vivi@intel.com
Use drm_mode_get_hv_timing() to fill out the plane clip rectangle.
No functional changes since pipe_src_w/h are already filled via
drm_mode_get_hv_timing().
Once everyone agrees on this we can move the clip handling into
drm_atomic_helper_check_plane_state().
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171123190502.28449-3-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Thierry Reding <treding@nvidia.com>
In order to guarantee that pipe_src_w/h matches the user mode h/vdisplay
we must not adjust pipe_src_w to accommodate double wide/dual link.
Instead just reject the mode outright.
This will allows us to rely on crtc_state->mode for plane clipping.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171123190502.28449-2-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Now that we can read the CSB from the HWSP, we may avoid having to
perform mmio reads entirely and so forgo the rigmarole of the forcewake
dance.
v2: Include forcewake hint for GEM_TRACE readback of mmio. If we don't
hold fw ourselves, the reads may return garbage.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180122100714.15137-1-chris@chris-wilson.co.uk
On gen9+, after an idle period the HW will disable the entire power well
to conserve power (by preventing current leakage). It takes around a 100
microseconds to bring the power well back online afterwards. With the
current hysteresis value of 25us (really 25 * 1280ns), we do not have
sufficient time to respond to an interrupt and schedule the next execution
before the HW powers itself down. (At present, we prevent this by
grabbing the forcewake for prolonged periods of time, but that overkill
fixed in the next patch.) The minimum we want to set the power gating
hysteresis to is the length of time it takes us to service the GPU, which
across a broad spectrum of machines is about 250us.
(Note this also brings guc latency into the same ballpark as execlists.)
v2: Include some notes on where I plucked the numbers from.
Testcase: igt/gem_exec_nop/sequential
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180122135541.32222-1-chris@chris-wilson.co.uk
We fail engine initialization if the scratch VMA cannot be created so
there is no point in error handle it later. If the initialization ordering
gets messed up, we can explode during development just as well.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180119100005.9072-2-tvrtko.ursulin@linux.intel.com
Render engine constructor helpers must only be called from the render
engine constructors, but there is no need to burden the production
binaries with warnings which can only be triggered during development.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180119100005.9072-1-tvrtko.ursulin@linux.intel.com
In case of eDP because the panel has a fixed mode, the link rate
and lane count at which it is trained corresponds to the link BW
required to support the native resolution of the panel. In case of
panles with lower resolutions where fewer lanes are hooked up internally,
that number is reflected in the MAX_LANE_COUNT DPCD register of the panel.
So it is pointless to fallback to lower link rate/lane count in case
of link training failure on eDP connector since the lower link BW
will not support the native resolution of the panel and we cannot
prune the preferred mode on the eDP connector.
In case of Link training failure on the eDP panel, something is wrong
in the HW internally and hence driver errors out with a loud
and clear DRM_ERROR message.
v2:
* Fix the DEBUG_ERROR and add {} in else (Ville Syrjala)
Cc: Clinton Taylor <clinton.a.taylor@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=103369
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1507835618-23051-1-git-send-email-manasi.d.navare@intel.com
If we fail to allocate a new request, make sure we recover the pages
that are in the process of being freed by inserting an RCU barrier.
v2: Comment before the shrink and barrier in the error path.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180119144657.22606-1-chris@chris-wilson.co.uk
It looks that GuC log functionality is not fully functional yet and
causes issues when enabled by auto(-1) modparam on debug builds.
For example, but not limited to:
[ 30.062893] ======================================================
[ 30.062894] WARNING: possible circular locking dependency detected
[ 30.062895] 4.15.0-rc8-CI-CI_DRM_3648+ #1 Tainted: G U
[ 30.062896] ------------------------------------------------------
[ 30.062897] debugfs_test/1268 is trying to acquire lock:
[ 30.062898] (&dev->struct_mutex){+.+.}, at: [<00000000e4213449>] i915_mutex_lock_interruptible+0x47/0x130 [i915]
[ 30.062921]
but task is already holding lock:
[ 30.062921] (&mm->mmap_sem){++++}, at: [<00000000dd7adc93>] __do_page_fault+0x106/0x560
[ 30.062924]
which lock already depends on the new lock.
References: 0ed8795353 ("drm/i915/guc: Redefine guc_log_level modparam values")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104693
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104694
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104695
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Saarinen <jani.saarinen@intel.com>
Cc: Tomi Sarvela <tomi.p.sarvela@intel.com>
Cc: Marta Lofstedt <marta.lofstedt@intel.com>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180119124926.29844-1-michal.wajdeczko@intel.com
Reviewed-by: Michal Winiarski <michal.winiarski@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Gen11 removes the Resource Streamer, which frees up a big chunk of
the context image. BSpec indicates 12544 DWORDs (13 pages), plus
one page for PPHWSP.
Please notice that, when looking at the BSpec context image table,
the right filter has to be applied as some rows are excluded for
specific GENs. Also, some rows apply per-subslice (for the
calculation above, we have supposed I915_MAX_SUBSLICES = 8).
v2: Rebase.
v3: Use the right size as per the BSpec.
v4:
- Rebased on top of the default context size (Rodrigo)
- Clarify in the commit message where the subslice calculation
comes from.
v5: s/12538/12544/ (Daniele)
BSpec: 18907
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Ben Widawsky <benjamin.widawsky@intel.com> (older version)
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1515711307-28979-2-git-send-email-oscar.mateo@intel.com
Instead of returning whatever size the latest GEN used. This is because
context sizes for new GENs can go up or down, but the only safe thing to
do for missing cases is to use the largest known one, whatever that is.
Suggested-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1515711307-28979-1-git-send-email-oscar.mateo@intel.com
MMIO addresses and register definition for the new interrupt
registers in Gen11.
v2: Removed spelt out VCS and VECS bit definitions. (Daniel Vetter)
v3: Adjust VCS and VECS. (Daniele Ceraolo Spurio)
v4: Bikeshedding (Paulo).
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180109232336.11029-5-paulo.r.zanoni@intel.com
In ICP, there are three TC ports and 3 DDI ports.
v2:
- Correct Pin mapping.
v3:
- Update pin mapping into per platform implementation
rather than previous approach of port wise mapping.
v4:
- Update GMBUS_NUM_PINS (Paulo)
v5:
- rebase.
v6:
- Update function name, GMBUS_PIN_NUM (Paulo)
v7 (from Paulo):
- Make it apply.
v8 (from Paulo):
- Maintain consistent if ladder ordering.
Suggested by: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111180010.24357-8-paulo.r.zanoni@intel.com
ICP has two backlight controllers - similar to previous platforms like
BXT -, but we only use one controller for now, so we can just reuse
the CNP code.
v2: Remove the usage of ICP_SECOND_PPS_BACKLIGHT register.(Jani)
Reuse CNP code since it is very similar.(Ville)
v3 (from Paulo): Rebase.
v4 (from Paulo): adjust commit message (James) and comment (Rodrigo).
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: James Ausmus <james.ausmus@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180119184812.2888-1-paulo.r.zanoni@intel.com
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
ICP, like BXT, has has two panel power sequencers.
v2: Simplify the code. Remove unwanted register definitions.
Make code as close to BXT style as possible. (Ville)
Also, remove the use of ICP_SECOND_PPS_BACKLIGHT for now.
Moving forward, if we are sure we need to set this register,
we can access it.
v3: Use INTEL_GEN(dev_priv), make code more readeable. (Ville)
v4 (from Paulo):
- Coding style fixes.
- Add a missing HAS_PCH_CNP -> gen10+ check.
- Rebase.
v5: Use per platform checks rather than INTEL_GEN().
v4 of this patch breaks on CoffeeLake, since CFL uses
CNP and per platform check makes sense in that case.
v6 (from Paulo):
- v5 was a patch on top of v4, not a new version. Now v6 is correctly
a new version of the original patch.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111180010.24357-6-paulo.r.zanoni@intel.com
Add register definitions for setting the rawclock.
Set the numerator,denominator and divider values.
v2: Simplify the commit message. Simplify the math.
Add register bits for numerator. (Paulo)
v3 (from Paulo): coding style bikesheds.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111180010.24357-5-paulo.r.zanoni@intel.com
Add the enum additions to ICP PCH.
v2 (from Paulo): don't set any platforms to it yet since ICP support is
incomplete.
v3 (from Rodrigo): Fix ICP name.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111180010.24357-4-paulo.r.zanoni@intel.com
Icelake is an Intel® Processor containing an Intel® Graphics
Controller.
This is just an initial Icelake definition. PCI IDs, Icelake support
and new features coming in following patches.
v2: Add .ddb_size and .has_guc (Michal Wajdeczko).
v3: Add the ICL_FEATURES macro (Kelvin Gardiner).
v4 (from Paulo): Add missing __initconst (Paulo) and say "graphics
controller" instead of something that looks like an official marketing
name but isn't (Chris).
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111180010.24357-3-paulo.r.zanoni@intel.com
Some Cannonlake SKUs will come with a full split between
port A and port E. This will be called port F although it
is not a 6th port, but only a split.
Note this patch alone is not sufficient for port F enabling,
it's just the first step.
v2: Fix size of dvo_ports found by Ander.
v3: Adding missing cases from intel_bios.c for Port_F
v4: Adding other missing cases and fix the commit message.
v5: Rebase on top of display headers rework.
v6 (from Paulo): improve commit message, bikeshed bit definitions.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111180010.24357-2-paulo.r.zanoni@intel.com
We may have fused or unused pipes in our system. Let's check that the pipe
in question is within limits of accessible pipes. In case, that we are not
able to access the pipe, we return early with a warning.
v2: Rephrasing of the commit message (Jani)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103206
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Jaswinder Singh Rajput <jaswinder@perfectintelligent.com>
Suggested-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1513584243-12607-1-git-send-email-mika.kahola@intel.com
SKL+ "sprites" no longer have 16KB max stride limit that earlier
platforms had. Bump up the limit to 32KB.
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Daniel Stone <daniels@collabora.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171222192231.17981-7-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Allow sprites to scan out compressed framebuffers.
Since different platforms have a different set of planes that
support CCS let's add a small helper to determine whether a
specific plane supports CCS or not. Currently that information
is spread around in many places, and not all the pieces of
code even agree with each other.
In addition to allowing sprites to scan out compressed fbs,
the other fix here is that we stop rejecting them on pipe C
on CNL.
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Daniel Stone <daniels@collabora.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171222192231.17981-6-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Split the g4x and snb cases into separate functions to match how we deal
with all other platforms. Also sort the switch cases to match the format
lists we've declared earlier, to ease comparisons.
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Daniel Stone <daniels@collabora.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171222192231.17981-5-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Y/Yf were dropped out from the SKL+ sprite modifier list on account
of some watermark issues Daniel Stone was having. My subsequent testing
seemed to indicate that things work better now, so add the modifiers
back in.
v2: Update the commit message with a better explanation
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Daniel Stone <daniels@collabora.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171222192231.17981-4-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The unreachable() is very much unreachable and the compiler knows
that, so there's no point in having it.
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Daniel Stone <daniels@collabora.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171222192231.17981-3-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
4K modes testing by using dummy EDID data has never been working
properly on boxes with DP++ (dual-mode) adaptors. The reason for
this is that those modes got pruned during hdmi mode validation.
intel_hdmi_mode_valid returns CLOCK_HIGH because the pixel clock
reported by the 4k mode is higher than dual port TMDS clock limit.
However 4k injection does work properly on machines that don't have
DP++ adapters because the mode is never validated against the DP++
TMDS clock limit.
v2: Don't detect the DP++ limits when we're testing using overridden
EDIDs. Make sure to check for the override condition after
respecting the value of drm_dp_dual_mode_detect (Jani Nikula).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101649
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Abdiel Janulgue <abdiel.janulgue@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171215102055.11729-1-abdiel.janulgue@linux.intel.com
drm_edid_to_eld() sets ELD connector type since commit 1d1c366507
("drm/edid: set ELD connector type in drm_edid_to_eld()"). Remove the
redundant update.
(Commit c945b8c14b ("drm/edid: build ELD in drm_add_edid_modes()") and
commit d471ed04b4 ("drm/drivers: drop redundant drm_edid_to_eld()
calls") are also related.)
v2: Rebase, update commit message with commit references.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171229125547.28672-1-jani.nikula@intel.com
HDCP compliant Repeaters can support max of 127 devices and max
depth of 7 for downstream topology.
If these max limits are exceeded, repeater will set the
topology error flags MAX_CASCADE_EXCEEDED and/or MAX_DEVS_EXCEEDED
in Bstatus followed by asserting READY/CP_IRQ for HDCP transmitter.
This patch check for these error flags as soon as READY bit is asserted.
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
[seanpaul fixed checkpatch alignment issue]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1516254488-4971-5-git-send-email-ramalingam.c@intel.com
Second stage of HDCP authentication starts at CP_IRQ or at the
assertion of READY bit from Repeater.
Till then repeater will be authenticating with its downstream devices.
So authenticated device count, depth and ksv_list readable from
repeaters are valid only after assertion of READY/CP_IRQ.
This patch makes sure that READY is polled before reading any
topology information.
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1516254488-4971-4-git-send-email-ramalingam.c@intel.com
Update VBT defs to reflect revision 216. While at it, default the
expected child device struct size to sizeof the size rather than a
hardcoded value.
v2: Fix bit order (David)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180118153310.32437-1-jani.nikula@intel.com
Display WA #1178 is meant to fix Aux channel voltage swing too low with
some type C dongles. Although it is for type C, HW engineers reported
that it can be applied to all external ports even if they are not going
to type C.
For CNL we apply the workaround every time Aux B, C and D are powering
up since they will lose the configuration when powered down.
v2: Use common tag for WA
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Arthur J Runyan <arthur.j.runyan@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171128220553.22435-1-lucas.demarchi@intel.com
Instead of using local string names that we will have to keep
maintaining, use the engine->name directly.
v2: Better invalid engine_id handling, capture_bo will not be able know
the engine_id and end up with -1 (Michal).
Suggested-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180110012151.28261-1-michel.thierry@intel.com
[ickle: minor massaging of function names]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180118175228.2830-1-chris@chris-wilson.co.uk
Today we have format mismatch between read/write operations
of i915_guc_log_control entry. For read we return (0, 1..4)
that represents disable/verbosity levels, but for write we
force user to follow internal structure format (0,1,9,11,13).
Let's hide internals from the user and accept same values
as we support for read and related guc_log_level modparam.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111152441.21676-2-michal.wajdeczko@intel.com
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We used value -1 to indicate "disabled" and values 0..3 to
indicate "enabled", but most of our other modparams are using
-1 for "auto" mode and 0 for "disable". For consistency let's
change our log level values to:
-1: auto (depends on platform and Kconfig.debug settings)
0: disabled
1: enabled (severity level 0 = min)
2: enabled (severity level 1)
3: enabled (severity level 2)
4: enabled (severity level 3 = max)
v2: fix commit message (Sagar)
display sanitized modparam value (Sagar)
unify sanitize messages (Sagar/Michal)
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111152441.21676-1-michal.wajdeczko@intel.com
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Watching a light workload on Baytrail (running glxgears and a 1080p
decode), instead of the system remaining at low frequency, the glxgears
would regularly trigger waitboosting after which it would have to spend
a few seconds throttling back down. In this case, the waitboosting is
counter productive as the minimal wait for glxgears doesn't prevent it
from functioning correctly and delivering frames on time. In this case,
glxgears happens to almost always be waiting on the current request,
which we already expect to complete quickly (see i915_spin_request) and
so avoiding the waitboost on the active request and spinning instead
provides the best latency without overcommitting to upclocking.
However, if the system falls behind we still force the waitboost.
Similarly, we will also trigger upclocking if we detect the system is
not delivering frames on time - again using a mechanism that tries to
detect a miss and not preemptively upclock.
v2: Also skip boosting for after missed vblank if the desired request is
already active.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180118131609.16574-1-chris@chris-wilson.co.uk
drivers/gpu/drm/i915/intel_dp.c: In function ‘intel_dp_hdcp_check_link’:
drivers/gpu/drm/i915/intel_dp.c:5191:26: error: ?: using integer constants in boolean context [-Werror=int-in-bool-context]
return ret >= 0 ? -EIO : ret;
Fixes: 20f24d776d ("drm/i915: Implement HDCP for DisplayPort")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180118161025.22700-1-chris@chris-wilson.co.uk
The CDCLK bypass frequency can vary on upcoming platforms, so prepare
for that now by tracking its value in the CDCLK state.
Currently on BDW+ the bypass frequency is always the reference clock and
I didn't bother with earlier platforms since it's not all that clear
what's the bypass clock on those.
I also didn't bother adding support for changing this frequency, since
atm I don't see any need for it.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180117172508.15993-1-imre.deak@intel.com
Since commit 4e773c3a8a ("drm/i915: Wire up shrinkctl->nr_scanned"),
we track the number of objects we scan and do not wish to exceed that as
it will overly penalise our own slabs under mempressure. Given that we
now know the target number of objects to scan, use that as our guide for
deciding to shrink as opposed to the number of objects we manage to
shrink (which doesn't correspond to the numbers we report to shrinkctl).
Fixes: 4e773c3a8a ("drm/i915: Wire up shrinkctl->nr_scanned")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180115212455.24046-2-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJaW+iVAAoJEHm+PkMAQRiGCDsIAJALNpX7odTx/8y+yCSWbpBH
E57iwr4rmnI6tXJY6gqBUWTYnjAcf4b8IsHGCO6q3WIE3l/kt+m3eA21a32mF2Db
/bfPGTOWu5LoOnFqzgH2kiFuC3Y474toxpld2YtkQWYxi5W7SUtIHi/jGgkUprth
g15yPfwYgotJd/gpmPfBDMPlYDYvLlnPYbTG6ZWdMbg39m2RF2m0BdQ6aBFLHvbJ
IN0tjCM6hrLFBP0+6Zn60pevUW9/AFYotZn2ankNTk5QVCQm14rgQIP+Pfoa5WpE
I25r0DbkG2jKJCq+tlgIJjxHKD37GEDMc4T8/5Y8CNNeT9Q8si9EWvznjaAPazw=
=o5gx
-----END PGP SIGNATURE-----
BackMerge tag 'v4.15-rc8' into drm-next
Linux 4.15-rc8
Daniel requested this for so the intel CI won't fall over on drm-next
so often.
struct timeval is deprecated because it cannot represent times
past 2038. In this driver, the only use of this structure is
to capture debug information. This is easily changed to ktime_t,
which we then format as needed when printing it later.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180117154916.219273-1-arnd@arndb.de
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
When testing that the timeout fired, we need to be sure we have waited
just long enough for the timeout to have occurred and for the softirq
(on another cpu) to have completed. Sleeping for an arbitrary amount is
prone to error, so wait for the timeout instead and complain if it was
too late.
v2: Use wait_event_timeout to provide an upper bound
v3: Fix inverted check for wait_event_timeout timing out
v4: Restore the check that the fences aren't signalled too early, by
inspecting them before the expected timeout.
References: https://bugs.freedesktop.org/show_bug.cgi?id=104670
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180117135713.2324-1-chris@chris-wilson.co.uk
It's perfectly legal to create a fb with stride < 512, and one of
the kms_plane_scaling subtests creates a very small fb.
Downgrade the WARN_ON to a simple check check, and because this
function is potentially called on every atomic update/pageflip,
downgrade the other WARN_ON to a WARN_ON_ONCE, and do the right
thing here.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180116155331.75175-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
intel_power_domains_init_hw() calls set_init_power, but when using
runtime power management this call is skipped. This prevents hw readout
from taking place.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104172
Link: https://patchwork.freedesktop.org/patch/msgid/20180116155324.75120-1-maarten.lankhorst@linux.intel.com
Fixes: bc87229f32 ("drm/i915/skl: enable PC9/10 power states during suspend-to-idle")
Cc: Nivedita Swaminathan <nivedita.swaminathan@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: <stable@vger.kernel.org> # v4.5+
Reviewed-by: Imre Deak <imre.deak@intel.com>
Tvrtko noticed that the comments describing the interaction of RCU and
the deferred worker for freeing drm_i915_gem_object were a little
confusing, so attempt to bring some sense to them.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180115205759.13884-1-chris@chris-wilson.co.uk
Check that we can successfully wait upon a dma_fence using the
i915_sw_fence, including the optional timeout mechanism.
v2: Account for the rounding up of the timeout to the next second.
Unfortunately, the minimum delay is then 1 second.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180115204348.8480-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
As freeing the objects require serialisation on struct_mutex, we should
prefer to use our singlethreaded driver wq that is dedicated to work
requiring struct_mutex (hence serialised).The benefit should be less
clutter on the system wq, allowing it to make progress even when the
driver/struct_mutex is heavily contended.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180115122846.15193-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
i830_disable_pipe() gets called from the power well code, and thus
we're already holding the power domain mutex. That means we can't
call plane->get_hw_state() as it will also try to grab the
same mutex and will thus deadlock.
Replace the assert_plane() calls (which calls ->get_hw_state()) with
just raw register reads in i830_disable_pipe(). As a bonus we can
now get a warning if plane C is enabled even though we don't even
expose it as a drm plane.
v2: Do a separate WARN_ON() for each plane (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Fixes: d87ce76402 ("drm/i915: Add .get_hw_state() method for planes")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171129125411.29055-1-ville.syrjala@linux.intel.com
(cherry picked from commit 5816d9cbc0)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Unify the plane disabling during state readout by pulling the code into
a new helper intel_plane_disable_noatomic(). We'll also read out the
state of all planes, so that we know which planes really need to be
diabled.
Additonally we change the plane<->pipe mapping sanitation to work by
simply disabling the offending planes instead of entire pipes. And
we do it before we otherwise sanitize the crtcs, which means we don't
have to worry about misassigned planes during crtc sanitation anymore.
v2: Reoder patches to not depend on enum old_plane_id
v3: s/for_each_pipe/for_each_intel_crtc/
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alex Villacís Lasso <alexvillacislasso@hotmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103223
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171117191917.11506-3-ville.syrjala@linux.intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
(cherry picked from commit b1e01595a6)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Add a .get_hw_state() method for planes, returning true or false
depending on whether the plane is enabled. Use it to rewrite the
plane enabled/disabled asserts in platform agnostic fashion.
We do lose the pre-gen4 plane<->pipe mapping checks, but since we're
supposed sanitize that anyway it doesn't really matter.
v2: Reoder patches to not depend on enum old_plane_id
Just call assert_plane_disabled() from assert_planes_disabled()
v3: Deal with disabled power wells in .get_hw_state()
v4: Rebase due skl primary plane code removal
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alex Villacís Lasso <alexvillacislasso@hotmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> #v2
Tested-by: Thierry Reding <thierry.reding@gmail.com> #v2
Link: https://patchwork.freedesktop.org/patch/msgid/20171117191917.11506-2-ville.syrjala@linux.intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
(cherry picked from commit 51f5a09639)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In order to prevent a race condition where we may end up overaccounting
the active state and leaving the busy-stats believing the GPU is 100%
busy, lock out the tasklet while we reconstruct the busy state. There is
no direct spinlock guard for the execlists->port[], so we need to
utilise tasklet_disable() as a synchronous barrier to prevent it, the
only writer to execlists->port[], from running at the same time as the
enable.
Fixes: 4900727d35 ("drm/i915/pmu: Reconstruct active state on starting busy-stats")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180115092041.13509-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
As the timeout mechanism has grown more and more complicated, using
multiple deferred tasks and more than doubling the size of our struct,
split the two implementations to streamline the simpler no-timeout
callback variant.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180115090643.26696-2-chris@chris-wilson.co.uk
Without an accompanying timer (for internal fences), we can free the
fence callback immediately as we do not need to employ the RCU barrier
to serialise with the timer. By avoiding the RCU delay, we can avoid the
extra mempressure under heavy inter-engine request utilisation.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180115090643.26696-1-chris@chris-wilson.co.uk
DPCD read for the eDP is complete by the time intel_psr_init() is
called, which means we can avoid initializing PSR structures and state
if there is no sink support.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180103213824.1405-3-dhinakaran.pandiyan@intel.com
The global variable dev_priv->psr.sink_support is set if an eDP sink
supports PSR. Use this instead of redoing the check with is_edp_psr().
Combine source and sink support checks into a macro that can be used to
return early from psr_{invalidate, single_frame_update, flush}.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180103213824.1405-2-dhinakaran.pandiyan@intel.com
This flag has become redundant since
commit 4d90f2d507 ("drm/i915: Start tracking PSR state in crtc state")
It is set at the same place as psr.enabled, which is also exposed via
debugfs.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180103213824.1405-1-dhinakaran.pandiyan@intel.com
drivers/gpu/drm/i915/i915_pmu.c:795:34-40: ERROR: application of sizeof to pointer
sizeof when applied to a pointer typed expression gives the size of
the pointer
Generated by: scripts/coccinelle/misc/noderef.cocci
Fixes: 109ec55837 ("drm/i915/pmu: Only enumerate available counters in sysfs")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180112170340.5387-1-tvrtko.ursulin@linux.intel.com
We have a hole in our busy-stat accounting if the pmu is enabled during
a long running batch, the pmu will not start accumulating busy-time
until the next context switch. This then fails tests that are only
sampling a single batch.
v2: Count each active port just once (context in/out events are only on
the first and last assignment to a port).
v3: Avoid hardcoding knowledge of 2 submission ports
Fixes: 30e17b7847 ("drm/i915: Engine busy time tracking")
Testcase: igt/perf_pmu/busy-start
Testcase: igt/perf_pmu/busy-double-start
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111073031.14614-1-chris@chris-wilson.co.uk
As we kmalloc our dynamic sysfs attributes, we have to give them an
external static lock_class_key for them to use with lockdep.
Fixes: 109ec55837 ("drm/i915/pmu: Only enumerate available counters in sysfs")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111140402.3984-1-chris@chris-wilson.co.uk
Switch over to dynamically creating device attributes, which are in turn
used by the perf core to expose available counters in sysfs.
This way we do not expose counters which are not avaiable on the current
platform, and are so more consistent between what we reply to open
attempts via the perf_event_open(2), and what is discoverable in sysfs.
v2:
* Simplify attribute pointer freeing loop.
* Changed attr init from macro to function.
* More common error unwind. (Chris Wilson)
* Rename some locals. (Chris Wilson)
v3:
* Fixed double semi-colon. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111083525.32394-1-tvrtko.ursulin@linux.intel.com
With firmware 1.07 having fixed the state corruption issue, we can enable
the headless GT performance workaround for CNL as well. (Equivalent to
b68763741a ("drm/i915: Restore GT performance in headless mode with DMC
loaded") on other affected platforms.)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100572
Testcase: igt/gem_exec_nop/headless
Cc: Imre Deak <imre.deak@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dmitry Rogozhkin <dmitry.v.rogozhkin@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111082417.795-1-tvrtko.ursulin@linux.intel.com
Geminilake requires the 3D driver to select whether barriers are
intended for compute shaders, or tessellation control shaders, by
whacking a "Barrier Mode" bit in SLICE_COMMON_ECO_CHICKEN1 when
switching pipelines. Failure to do this properly can result in GPU
hangs.
Unfortunately, this means it needs to switch mid-batch, so only
userspace can properly set it. To facilitate this, the kernel needs
to whitelist the register.
The workarounds page currently tags this as applying to Broxton only,
but that doesn't make sense. The documentation for the register it
references says the bit userspace is supposed to toggle only exists on
Geminilake. Empirically, the Mesa patch to toggle this bit appears to
fix intermittent GPU hangs in tessellation control shader barrier tests
on Geminilake; we haven't seen those hangs on Broxton.
v2: Mention WA #0862 in the comment (it doesn't have a name).
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180105085905.9298-1-kenneth@whitecape.org
(cherry picked from commit ab062639ed)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This register does not contain it. Instead, we have to look into FAULT_TLB_DATA0 & 1
(where, by the way, we can also get the address space).
v2: Right formatting
v3:
- Use 12 (as per the register format) instead of PAGE_SIZE (Chris)
- s/BITS_44_TO_47/HIGHBITS (Chris)
- Right formatting, this time for real
Fixes: b03ec3d67a ("drm/i915: There is only one fault register from GEN8 onwards")
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1513982329-32191-1-git-send-email-oscar.mateo@intel.com
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
While moving code around for solving lockdep issue for GuC log relay,
spotted that uc_fini_wq is not being called in failure path in gem_init.
Missed in the below commit. Add it.
v2: Removed GEM_BUG_ON(!HAS_GUC()) from intel_uc_fini_wq as init happens
only based on enable_guc module parameter and does not consider has_guc
capability. (Michal)
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Fixes: 3176ff49bc ("drm/i915/guc: Move GuC workqueue allocations outside of the mutex")
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1515588857-10283-1-git-send-email-sagar.a.kamble@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Instead of always trying to disable HDCP. Only run hdcp_disable when the
state is not UNDESIRED. This will catch cases where it's enabled and
also cases where enable failed and the state is left in DESIRED mode.
Note that things won't blow up if disable is attempted while already
disabled, it's just bad form.
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180109185330.16853-1-seanpaul@chromium.org
The power domain masks are 64 bit wide, so we need BIT_ULL() when
setting bits in them, these ones were missed during converting from 32
to 64 bit masks. All 3 enums are <32 atm, so this didn't cause a real
problem.
Fixes: d8fc70b736 ("drm/i915: Make power domain masks 64 bit long")
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180109122040.19425-1-imre.deak@intel.com
The ACK/NACK implementation as found in e.g. the G965 has the falling
clock edge and the release of the data line after the ACK for the received
byte happen at the same time.
This is conformant with the I2C specification, which allows a zero hold
time, see footnote [3]: "A device must internally provide a hold time of
at least 300 ns for the SDA signal (with respect to the V IH(min) of the
SCL signal) to bridge the undefined region of the falling edge of SCL."
Some HDMI-to-VGA converters apparently fail to adhere to this requirement
and latch SDA at the falling clock edge, so instead of an ACK
sometimes a NACK is read and the slave (i.e. the EDID ROM) ends the
transfer.
The bitbanging releases the data line for the ACK only 1/4 bit time after
the falling clock edge, so a slave will see the correct value no matter
if it samples at the rising or the falling clock edge or in the center.
Fallback to bitbanging is already done for the CRT connector.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92685
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/a39f080b-81a5-4c93-b3f7-7cb0a58daca3@rwthex-w2-a.rwth-ad.de
This patch adds HDCP support for DisplayPort connectors by implementing
the intel_hdcp_shim.
Most of this is straightforward read/write from/to DPCD registers. One
thing worth pointing out is the Aksv output bit. It wasn't easily
separable like it's HDMI counterpart, so it's crammed in with the rest
of it.
Changes in v2:
- Moved intel_hdcp_check_link out of intel_dp_check_link and only call
it on short pulse. Since intel_hdcp_check_link does its own locking,
this ensures we don't deadlock when intel_dp_check_link is called
holding connection_mutex.
- Rebased on drm-intel-next
Changes in v3:
- Initialize new worker
Changes in v4:
- Use intel_hdcp_init (Daniel)
- Check for reauth requests in check_link (Ram)
Changes in v5:
- None
Changes in v6:
- Fix build warnings when printing ssize_t
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180108195545.218615-10-seanpaul@chromium.org
This patch adds HDCP support for HDMI connectors by implementing
the intel_hdcp_shim.
Nothing too special, just a bunch of DDC reads/writes.
Changes in v2:
- Rebased on drm-intel-next
Changes in v3:
- Initialize new worker
Changes in v4:
- Remove SKL_ prefix from most register names (Daniel)
- Wrap sanity checks in WARN_ON (Daniel)
- Consolidate the enable/disable functions into one toggle fn
- Use intel_hdcp_init (Daniel)
Changes in v5:
- checkpatch whitespace nits
Changes in v6:
- None
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180108195545.218615-9-seanpaul@chromium.org
Once the Aksv is available in the PCH, we need to get it on the wire to
the receiver via DDC. The hardware doesn't allow us to read the value
directly, so we need to tell GMBUS to source the Aksv internally and
send it to the right offset on the receiver.
The way we do this is to initiate an indexed write where the index is
the Aksv register offset. We write dummy values to GMBUS3 as if we were
sending the key, and the hardware slips in the "real" values when it
goes out.
Changes in v2:
- None
Changes in v3:
- Uses new index write feature (Ville)
Changes in v4:
- None
Changes in v5:
- checkpatch whitespace fix
Changes in v6:
- None
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180108195545.218615-8-seanpaul@chromium.org
This patch enables the indexed write feature of the GMBUS to concatenate
2 consecutive messages into one. The criteria for an indexed write is
that both messages are writes, the first is length == 1, and the second
is length > 0. The first message is sent out by the GMBUS as the slave
command, and the second one is sent via the GMBUS FIFO as usual.
Changes in v3:
- Added to series
Changes in v4:
- Combine indexed reads and writes (Ville)
Changes in v5:
- checkpatch whitespace nits
Changes in v6:
- None
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180108195545.218615-7-seanpaul@chromium.org
This patch adds the framework required to add HDCP support to intel
connectors. It implements Aksv loading from fuse, and parts 1/2/3
of the HDCP authentication scheme.
Note that without shim implementations, this does not actually implement
HDCP. That will come in subsequent patches.
Changes in v2:
- Don't open code wait_fors (Chris)
- drm_hdcp.c under MIT license (Daniel)
- Move intel_hdcp_disable() call above ddi_disable (Ram)
- Fix // comments (I wore a cone of shame for 12 hours to atone) (Daniel)
- Justify intel_hdcp_shim with comments (Daniel)
- Fixed async locking issues by adding hdcp_mutex (Daniel)
- Don't alter connector_state in enable/disable (Daniel)
Changes in v3:
- Added hdcp_mutex/hdcp_value to make async reasonable
- Added hdcp_prop_work to separate link checking & property setting
- Added new helper for atomic_check state tracking (Daniel)
- Moved enable/disable into atomic_commit with matching helpers
- Moved intel_hdcp_check_link out of all locks when called from dp
- Bumped up ksv_fifo timeout (noticed failure on one of my dongles)
Changes in v4:
- Remove SKL_ prefix from most register names (Daniel)
- Move enable/disable back to modeset path (Daniel)
- s/get_random_long/get_random_u32/ (Daniel)
- Remove mode_config.mutex lock in prop_work (Daniel)
- Add intel_hdcp_init to handle init of conn components (Daniel)
- Actually check return value of attach_property
- Check Bksv is valid before trying to authenticate (Ram)
Changes in v5:
- checkpatch whitespace changes
- s/DRM_MODE_CONTENT_PROTECTION_OFF/DRM_MODE_CONTENT_PROTECTION_UNDESIRED/
- Fix ksv list wait timeout (actually wait 5s)
- Increase the R0 timeout to 300ms (Ram)
Changes in v6:
- SPDX license
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ramalingam C <ramalingm.c@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180108195545.218615-6-seanpaul@chromium.org
This patch adds a little more control to a couple wait_for routines such
that we can avoid open-coding read/wait/timeout patterns which:
- need the value of the register after the wait_for
- run arbitrary operation for the read portion
This patch also chooses the correct sleep function (based on
timers-howto.txt) for the polling interval the caller specifies.
Changes in v2:
- Added to the series
Changes in v3:
- Rebased on drm-intel-next-queued and the new Wmin/max _wait_for
- Removed msleep option
Changes in v4:
- Removed ; for OP in _wait_for (Chris)
- Moved reg_value definition above ret (Chris)
Changes in v4:
- checkpatch whitespace fix
Changes in v5:
- None
Changes in v6:
- None
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180108195545.218615-3-seanpaul@chromium.org
Geminilake requires the 3D driver to select whether barriers are
intended for compute shaders, or tessellation control shaders, by
whacking a "Barrier Mode" bit in SLICE_COMMON_ECO_CHICKEN1 when
switching pipelines. Failure to do this properly can result in GPU
hangs.
Unfortunately, this means it needs to switch mid-batch, so only
userspace can properly set it. To facilitate this, the kernel needs
to whitelist the register.
The workarounds page currently tags this as applying to Broxton only,
but that doesn't make sense. The documentation for the register it
references says the bit userspace is supposed to toggle only exists on
Geminilake. Empirically, the Mesa patch to toggle this bit appears to
fix intermittent GPU hangs in tessellation control shader barrier tests
on Geminilake; we haven't seen those hangs on Broxton.
v2: Mention WA #0862 in the comment (it doesn't have a name).
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180105085905.9298-1-kenneth@whitecape.org
There is a new version of DMC available for CNL.
The release notes mentions:
1. Fix for the issue where DC_STATE was getting enabled
even when disabled by driver causing data corruption
v2: Since the firmware is merged to linux-firmware.git,
add MODULE_FIRMWARE.
v3: rebased. Correct commit message(Jani)
Cc: Jani Saarinen <jani.saarinen@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1515109902-14076-1-git-send-email-anusha.srivatsa@intel.com
Since the firmwares are not yet released to public repo,
disable them on Geminilake.
v2: Remove the firmware versions (Michal)
v3: Remove unwanted defines (Rodrigo)
Correct commit message (Michal)
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Fixes: 90f192c824 ("drm/i915/GuC/GLK: Load GuC on GLK")
Fixes: db5ba0d893 ("drm/i915/GLK/HuC: Load HuC on GLK")
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1515006225-13003-1-git-send-email-anusha.srivatsa@intel.com
In some iommu, e.g. swiotlb, the available space can be quite limited.
So we employ a trial-and-error approach to seeing if our large
contiguous chunks can fit, and if that fails we try again with smaller
chunks after trying to free our own lazily allocated blobs. As we use a
trial-and-error approach, we do not want dma_map_sg() to emit a WARN of
its own accord, we want to gracefully report the error back to the caller
instead.
Note that our noisy culprit, swiotlb, doesn't honour the flag, yet.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180104163842.11635-1-chris@chris-wilson.co.uk
Display WA #1183 was recently added to workaround
"Failures when enabling DPLL0 with eDP link rate 2.16
or 4.32 GHz and CD clock frequency 308.57 or 617.14 MHz
(CDCLK_CTL CD Frequency Select 10b or 11b) used in this
enabling or in previous enabling."
This workaround was designed to minimize the impact only
to save the bad case with that link rates. But HW engineers
indicated that it should be safe to apply broadly, although
they were expecting the DPLL0 link rate to be unchanged on
runtime.
We need to cover 2 cases: when we are in fact enabling DPLL0
and when we are just changing the frequency with small
differences.
This is based on previous patch by Rodrigo Vivi with suggestions
from Ville Syrjälä.
Cc: Arthur J Runyan <arthur.j.runyan@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171204232210.4958-1-lucas.demarchi@intel.com
(cherry picked from commit 53421c2fe9)
[ Lucas: Backport to 4.15 adding back variable that has been removed on
commits not meant to be backported ]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180102201837.6812-1-lucas.demarchi@intel.com
A shadow page table entry needs to be cleared after being set as
post-sync. This patch fixes the recent error reported in Win7-32 test.
Fixes: 2707e44466 ("drm/i915/gvt: vGPU graphics memory virtualization")
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Instead of returning -EINVAL, GEM_BUG_ON when GuC reset is invoked for
platforms not supporting as we don't expect to invoke it.
v2: re-wording commit message and subject (Sagar)
Signed-off-by: Sujaritha Sundaresan <sujaritha.sundaresan@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1514928025-29659-2-git-send-email-sujaritha.sundaresan@intel.com
The Additional Data Struct (ADS) contains objects that are required by
GuC post FW load and are not necessarily submission-only. Even with
submission disabled we may require something inside the ADS, so it
makes more sense for them to be always created.
Similarly, we need to access GuC logs and even if GuC submission
is disabled, to debug issues with GuC loading or with whatever we're using
GuC for.
v2: re-wording commit message (Sagar)
Signed-off-by: Sujaritha Sundaresan <sujaritha.sundaresan@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1514928025-29659-1-git-send-email-sujaritha.sundaresan@intel.com
After staring at the list_for_each_safe macros for a bit, our current
invocation of list_safe_reset_next in execlists_schedule() simply
reduces to list_for_each.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180102151235.3949-11-chris@chris-wilson.co.uk
The dependency chain must be an acyclic graph. This is checked by the
swfence, but for sanity, also do a simple check that we do not corrupt
our list iteration in execlists_schedule() by a shallow dependency
cycle.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180102151235.3949-10-chris@chris-wilson.co.uk
Back up our comment that all signalers should have been signaled before
we ourselves were retired with an assert to that effect.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180102151235.3949-9-chris@chris-wilson.co.uk
To modify the global seqno may require rewriting a few registers, which
requires us to hold the rpm wakeref. We must therefore take it around
the call to i915_gem_set_global_seqno() in debugfs, on behalf of the
user.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180102151235.3949-15-chris@chris-wilson.co.uk
Move the clearing of the CS-interrupt into the engine reset phase,
before the current init-hw phase. This helps clarify that we clear the
pending interrupts prior to any restarting of the execlists.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180102151235.3949-16-chris@chris-wilson.co.uk
i915_gem_request_assign() is not used since commit 77f0d0e925
("drm/i915/execlists: Pack the count into the low bits of the
port.request"), so remove the defunct code
References: 77f0d0e925 ("drm/i915/execlists: Pack the count into the low bits of the port.request")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180102151235.3949-1-chris@chris-wilson.co.uk
Reduce the number of GGTT PTE operations to speed the test up, but we
reduce the likelihood of spotting a coherency error in those operations.
However, Broxton is sporadically timing on this test, presumably because
its GGTT operations are all uncached.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171223110407.21402-1-chris@chris-wilson.co.uk
We have plenty of global registers and whatnot programmed without
any further locking by the modeset code. Currently non-bocking
modesets are allowed to execute in parallel which could corrupt
said registers.
To avoid the problem let's run all non-blocking modesets on an
ordered workqueue. We still put page flips etc. to system_unbound_wq
allowing page flips on one pipe to execute in parallel with page flips
or a modeset on a another pipe (assuming no known state is shared
between them, at which point they would have been added to the same
atomic commit and serialized that way).
Blocking modesets are already serialized with each other by
connection_mutex, and thus are safe. To serialize them with
non-blocking modesets we just flush the workqueue before executing
blocking modesets.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 94f050246b ("drm/i915: nonblocking commit")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171113133622.8593-1-ville.syrjala@linux.intel.com
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
(cherry picked from commit 757fffcfdf)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Commit 77affa3172 ("drm/i915/psr: Fix compiler warnings for
hsw_psr_disable()") swapped status and control registers while fixing
indentation. The _ctl at the end of the status register name must have to
led to this.
Fixes: 77affa3172 ("drm/i915/psr: Fix compiler warnings for hsw_psr_disable()")
References: https://www.mrc-cbu.cam.ac.uk/people/matt.davis/cmabridge/
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171220043520.2599-1-dhinakaran.pandiyan@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 14c6547d6d)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Existing debugfs entry i915_drrs_status is updated with whether PSR
is the cause for DRRS disabled state.
[v2]: Dropped the module parameter details as ctl moved from module
parameter to debugfs. [Rodrigo]
[v3]: Crtc ID information is dropped as there is no immediate usecase.
[Rodrigo].
Signed-off-by: C, Ramalingam <ramalingam.c@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1511151827-6596-1-git-send-email-ramalingam.c@intel.com
Debugfs called i915_drrs_ctl is added to enable and disable the
eDP DRRS. Writing 0 will disable the feature, whereas non-zero
will enable the feature.
Possibility of disabling the DRRS, enables the testing of the
frontbuffer tracking based features (FBC, DRRS and PSR) as
standalone or any combination of the set.
[v2]: ctl interface is moved from module parameter to debugfs [Rodrigo]
Signed-off-by: C, Ramalingam <ramalingam.c@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1510079903-29441-1-git-send-email-ramalingam.c@intel.com
At least on the Chuwi Vi8 (non pro/plus) the LCD panel will show an image
shifted aprox. 20% to the left (with wraparound) and sometimes also wrong
colors, showing that the panel controller is starting with sampling the
datastream somewhere mid-line. This happens after the first blanking and
re-init of the panel.
After looking at drm.debug output I noticed that initially we inherit the
cdclk of 333333 KHz set by the GOP, but after the re-init we picked 266667
KHz, which turns out to be the cause of this problem, a quick hack to hard
code the cdclk to 333333 KHz makes the problem go away.
I've tested this on various Bay Trail devices, to make sure this not does
cause regressions on other devices and the higher cdclk does not cause
any problems on the following devices:
-GP-electronic T701 1024x600 333333 KHz cdclk after this patch
-PEAQ C1010 1920x1200 333333 KHz cdclk after this patch
-PoV mobii-wintab-800w 800x1280 333333 KHz cdclk after this patch
-Asus Transformer-T100TA 1368x768 320000 KHz cdclk after this patch
Also interesting wrt this is the comment in vlv_calc_cdclk about the
existing workaround to avoid 200 Mhz as clock because that causes issues
in some cases.
This commit extends the "do not use 200 Mhz" workaround with an extra
check to require atleast 320000 KHz (avoiding 266667 KHz) when a DSI
panel is active.
Changes in v2:
-Change the commit message and the code comment to not treat the GOP as
a reference, the GOP should not be treated as a reference
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171220105017.11259-1-hdegoede@redhat.com
Display WA #1183 was recently added to workaround
"Failures when enabling DPLL0 with eDP link rate 2.16
or 4.32 GHz and CD clock frequency 308.57 or 617.14 MHz
(CDCLK_CTL CD Frequency Select 10b or 11b) used in this
enabling or in previous enabling."
This workaround was designed to minimize the impact only
to save the bad case with that link rates. But HW engineers
indicated that it should be safe to apply broadly, although
they were expecting the DPLL0 link rate to be unchanged on
runtime.
We need to cover 2 cases: when we are in fact enabling DPLL0
and when we are just changing the frequency with small
differences.
This is based on previous patch by Rodrigo Vivi with suggestions
from Ville Syrjälä.
Cc: Arthur J Runyan <arthur.j.runyan@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171204232210.4958-1-lucas.demarchi@intel.com
Looking at a CI failure with an ominous line of
[ 362.550715] hangcheck current seqno ffffff6b, last ffffff8c, hangcheck ffffff6b [6016 ms], inflight 118
with no apparent cause for the seqno to be negative, left me wondering
if someone had scribbled over the HWSP. So include the HWSP in the
engine dump to see if there are more signs of random scribbling.
v2: Fix row pointer, i is now incremented by 8 so doesn't need scaling
by 8, and we don't need to keep volatile here as the status_page isn't
marked up as volatile itself.
v3: Use hexdump, with suppression of identical lines. (Tvrtko)
Which results in
HWSP:
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
*
00000040 00000001 00000000 00000018 00000002 00000001 00000000 00000018 00000000
00000060 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000003
00000080 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
*
000000c0 00000002 00000000 00000000 00000000 00000000 00000000 00000000 00000000
000000e0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
*
instead of 128 lines of mostly 0s.
v4: Tidy up the locals
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171222182521.18106-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
We should only attempt to remove requests from the execution queue that
are on the execution queue. These are the requests that have been
assigned a global_seqno, so we can assert that we only attempt to remove
requests with a nonzero global_seqno. Afterwards we assert that we
remove them in order, i.e. the global_seqno matches the engine's seqno,
but that leaves a small loophole for an unattached request on an unused
engine.
We can then make the same assertion on queuing the request to the
execution engine, it must have a zero global_seqno or else we are queuing
the same request twice.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171222141959.3006-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
We have plenty of global registers and whatnot programmed without
any further locking by the modeset code. Currently non-bocking
modesets are allowed to execute in parallel which could corrupt
said registers.
To avoid the problem let's run all non-blocking modesets on an
ordered workqueue. We still put page flips etc. to system_unbound_wq
allowing page flips on one pipe to execute in parallel with page flips
or a modeset on a another pipe (assuming no known state is shared
between them, at which point they would have been added to the same
atomic commit and serialized that way).
Blocking modesets are already serialized with each other by
connection_mutex, and thus are safe. To serialize them with
non-blocking modesets we just flush the workqueue before executing
blocking modesets.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 94f050246b ("drm/i915: nonblocking commit")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171113133622.8593-1-ville.syrjala@linux.intel.com
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Gen9+ need to disable GMBUS clock gating when doing multi part
transfers. Otherwise clock gating will kick in when GMBUS is in
the WAIT state and presumably that will corrupt the transfer.
This is documented as Display WA #0868.
Apparently older hardware doesn't allow clock gating in the WAIT
state and thus are unaffected by this problem.
v2: Limit the PCH w/a to gen9 and gen10 only (DK)
Actually change it to check the PCH type instead since
it's the PCH that actually contains the GMBUS hardware
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20171221202432.17373-1-ville.syrjala@linux.intel.com
Sean Paul