This patch implements proper transmission flow control on mshX.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split wlan_add_card() into a part that just setups kernel parameters and
into the function libertas_activate_card(), which will implizitly use
hardware functions by the started thread.
This allows us later to do something like this:
priv = libertas_add_card();
priv->hw_command_to_host = if_usb_command_to_host;
priv->hw_xxxx = if_usb_xxxx;
priv->hw_yyyy = if_usb_yyyy;
wlan_activate_card()
and of course the CF driver can set it's own functions.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The reset_device() logic is only needed for USB devices, not for CF
devices.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* a newline was missing
* changed %32s to '%s', no need to right justify the ESSID
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's not really needed, because we can call wlan_remove_card() with
wlan_private* anyway.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It used to be LBS_DEB_MAIN, now it's LBS_DEB_THREAD
Also fixed a missing ":" in lbs_deb_enter()
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patches adds the two functions wlan_add_mesh() and wlan_remove_mesh(),
which are responsible for the mshX interface. In a CF driver with a non-
mesh-aware firmware you can omit the calls to this functions.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* renamed module parameter back to libertas_debug
* change from bit shifts to constants, that way it's easier to look at the
source and specify the libertas_debug=0xXXXX module parameter
* moved module_param from fw.c to main.c, where it belongs better
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The debug output of libertas was either not present or it was overwhelming.
This patch adds the possibility to specify a bitmask for the area of
interest. One should then only get the desired output.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reduces usb8xxx.ko by 951 bytes (text) and 256 bytes (data)
when PROC_DEBUG isn't defined.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The previous scan fix did not account for scan paths other than set_scan()
that need to do a full scan at once.
Add a "full_scan" parameter to wlan_scan_networks() to control such
behaviour.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move libertas_wlan_data_rates into wext.c and make it static. wext.c is the
only user of this array.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For me it looks cleaner, because it removes one level of indirection.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
DEV_NAME_LEN is already defined in defs.h and that is sufficient.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove filename from debug output because it's way too long.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rmmod did not remove /sys/kernel/debug/libertas_wireless/eth1/
subscribed_events/high_snr. After I fixed this, I noticed that
it also didn't remove /sys/kernel/debug/libertas_wireless/eth1
as well.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Renames wlan_association_worker into libertas_association_worker
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Scan two channels per each command on set_scan(), then bail out and let
get_scan() continue the scanning work up to the last channel.
This gives time to the firmware so it can go back to the association
channel and keep the connection alive.
Fixes http://dev.laptop.org/ticket/841
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
skb could have been freed by then. Also, in libertas_upload_rx_packet(),
skb->protocol is initialized by eth_type_trans().
Signed-off-by: Eugene Teo <eugeneteo@kernel.sg>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NULL checks should be performed before the dereference.
Spotted by the Coverity checker.
Signed-off-by: Eugene Teo <eteo@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In libertas_process_rxed_packet() and process_rxed_802_11_packet() the
skb is dereferenced after being passed to netif_rx (called from
libertas_upload_rx_packet). Spotted by Coverity (1658, 1659).
Also, libertas_upload_rx_packet() unconditionally returns 0 so the error
check is dead code - might as well take it out and change the signature.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
made debugfs.c sparse-clean, found an unused function that way
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the static definition of SUPPORT_BOOT_COMMAND.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also change WEPstatus to "wep_enabled"; it's clearer and consistent with the
WPAenabled and WPA2enabled members.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove WLAN_802_11_AUTHENTICATION_MODE enum and use IW_AUTH_ALG_* instead.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove setencryptionmode private ioctl and Encryptionmode variable.
Mostly unused, and its functionality is provided by other internal members
like WEPstatus, WPAenabled, WPA2enabled, and SIOCSIWGENIE.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Obsoleted by SIOCSIWAUTH's IW_AUTH_80211_AUTH_ALG option introduced
by WE-18.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Useless; it set an internal variable that was unused anyway.
A supplicant handles all 802.1x authentication, not the driver.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Start to normalize bss_descriptor with ieee80211_network so we can
eventually replace bss_descriptor more easily.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cleanup drivers/net/wireless/libertas/debugfs.c to use standard kernel
macros and functions.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the Marvell Libertas 8388 802.11 USB driver.
Signed-off-by: Marcelo Tosatti <marcelo@kvack.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Javier Cardona