Now that ehci_run don't call ehci_reset, we can use ehci_run.
Signed-off-by: Matthieu CASTET <castet.matthieu@parrot.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
TDI driver does the ehci_reset in their reset callback.
Don't reset in ehci_run because configuration settings done in
platform driver will be reset.
This will allow to make msm use ehci_run.
Signed-off-by: Matthieu CASTET <castet.matthieu@parrot.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The document says:
|2.1 Problem description
| When at least two USB devices are simultaneously running, it is observed that
| sometimes the INT corresponding to one of the USB devices stops occurring. This may
| be observed sometimes with USB-to-serial or USB-to-network devices.
| The problem is not noticed when only USB mass storage devices are running.
|2.2 Implication
| This issue is because of the clearing of the respective Done Map bit on reading the ATL
| PTD Done Map register when an INT is generated by another PTD completion, but is not
| found set on that read access. In this situation, the respective Done Map bit will remain
| reset and no further INT will be asserted so the data transfer corresponding to that USB
| device will stop.
|2.3 Workaround
| An SOF INT can be used instead of an ATL INT with polling on Done bits. A time-out can
| be implemented and if a certain Done bit is never set, verification of the PTD completion
| can be done by reading PTD contents (valid bit).
| This is a proven workaround implemented in software.
Russell King run into this with an USB-to-serial converter. This patch
implements his suggestion to enable the high frequent SOF interrupt only
at the time we have ATL packages queued. It goes even one step further
and enables the SOF interrupt only if we have more than one ATL packet
queued at the same time.
Cc: <stable@kernel.org> # [2.6.35.x, 2.6.36.x, 2.6.37.x]
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ehci_lpm_set_da and ehci_lpm_check are EHCI 1.1 specific functions which
are not used on many platforms but do generate annoying gcc warnings
Signed-off-by: Maksim Rayskiy <mrayskiy@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed to resolve some merge conflicts that were found
in the USB host controller patches, and reported by Stephen Rothwell.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit b7d5b439b7.
It conflicts with commit baab93afc2 "USB:
EHCI: ASPM quirk of ISOC on AMD Hudson" and merging the two just doesn't
work properly.
Cc: Andiry Xu <andiry.xu@amd.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alex He <alex.he@amd.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the below compilation errors.
CC drivers/usb/gadget/ci13xxx_msm.o
CC net/mac80211/led.o
drivers/usb/gadget/ci13xxx_msm.c: In function 'ci13xxx_msm_notify_event':
drivers/usb/gadget/ci13xxx_msm.c:42: error: 'USB_AHBBURST' undeclared (first use in this function)
drivers/usb/gadget/ci13xxx_msm.c:42: error: (Each undeclared identifier is reported only once
drivers/usb/gadget/ci13xxx_msm.c:42: error: for each function it appears in.)
drivers/usb/gadget/ci13xxx_msm.c:43: error: 'USB_AHBMODE' undeclared (first use in this function)
make[4]: *** [drivers/usb/gadget/ci13xxx_msm.o] Error 1
make[3]: *** [drivers/usb/gadget] Error 2
MSM USB driver is not supported on boards like trout (MSM7201) which
has an external PHY.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The convention is to prefix symbols exported from the USB HCD core with
"usb_hcd". This change makes unmap_urb_setup_for_dma() and
unmap_urb_for_dma() consistent with that.
Signed-off-by: Robert Morell <rmorell@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In create_companion_file() there is a bogus assignemt to i created for
the express purpose of avoiding an ignored return value warning.
With pre-release GCC-4.6, this causes a 'set but not used' warning.
Kick the problem further down the road by just returning i. All the
callers of create_companion_file() ignore its return value, so all is
good:
o No warnings are issued.
o We still subvert the desires of the authors of device_create_file()
by ignorning error conditions.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With pre-release GCC-4.6, we get a 'set but not used' warning when
EHCI_URB_TRACE is not set because we set the qtd variable without
using it.
Rearrange the statements so that we only set qtd if it will be used.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The vdbg macro is not used anywhere so it can be removed.
With pre-release GCC-4.6, there are several complaints of variables
that are 'set but not used' caused by the ehci_vdbg() macro expanding
to something that does not contain any of its arguments. We can quiet
this warning by rewriting ehci_vdbg() as a variadic static inline that
does nothing.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The pre-release GCC-4.6 now correctly flags this code as dead.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch moves the AMD PLL quirk code in OHCI/EHCI driver to pci-quirks.c,
and exports the functions to be used by xHCI driver later.
AMD PLL quirk disable the optional PM feature inside specific
SB700/SB800/Hudson-2/3 platforms under the following conditions:
1. If an isochronous device is connected to OHCI/EHCI/xHCI port and is active;
2. Optional PM feature that powers down the internal Bus PLL when the link is
in low power state is enabled.
Without AMD PLL quirk, USB isochronous stream may stutter or have breaks
occasionally, which greatly impair the performance of audio/video streams.
Currently AMD PLL quirk is implemented in OHCI and EHCI driver, and will be
added to xHCI driver too. They are doing similar things actually, so move
the quirk code to pci-quirks.c, which has several advantages:
1. Remove duplicate defines and functions in OHCI/EHCI (and xHCI) driver and
make them cleaner;
2. AMD chipset information will be probed only once and then stored.
Currently they're probed during every OHCI/EHCI initialization, move
the detect code to pci-quirks.c saves the repeat detect cost;
3. Build up synchronization among OHCI/EHCI/xHCI driver. In current
code, every host controller enable/disable PLL only according to
its own status, and may enable PLL while there is still isoc transfer on
other HCs. Move the quirk to pci-quirks.c prevents this issue.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alex He <alex.he@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-greg' of git://gitorious.org/usb/usb:
usb: ehci-omap: Show fatal probing time errors to end user
usb: musb: introduce api for dma code to check compatibility with usb request
usb: musb: maintain three states for buffer mappings instead of two
usb: musb: disable double buffering when it's broken
usb: musb: hsdma: change back to use musb_read/writew
usb: musb: core: fix IRQ check
usb: musb: fix kernel panic during s2ram(v2)
In drivers/usb/host/sl811-hcd.c::sl811h_urb_enqueue(), memory is allocated
with kzalloc() and assigned to 'ep'. If we leave via the 'fail' label due
to 'if (ep->maxpacket > H_MAXPACKET)', then 'ep' will go out of scope
without having been assigned to anything, so we'll leak the memory we
allocated.
This patch fixes the leak by simply calling kfree(ep); before jumping to
the 'fail' label.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are a few error paths in ehci_hcd_omap_probe that can be triggered
because of memory allocation or hw failure. Change those dev_dbg error
prints to dev_err with an error code printed so that the end users are able
to notice the issue.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
* 'for-usb-linus' of master.kernel.org:/pub/scm/linux/kernel/git/sarah/xhci:
xhci: Remove more doorbell-related reads
xHCI: fix printk_ratelimit() usage
xHCI: replace dev_dbg() with xhci_dbg()
xHCI: fix cycle bit set in giveback_first_trb()
xHCI: remove redundant parameter in giveback_first_trb()
xHCI: fix queue_trb in isoc transfer
xhci: Use GFP_NOIO during device reset.
usb: Realloc xHCI structures after a hub is verified.
xhci: Do not run xhci_cleanup_msix with irq disabled
xHCI: synchronize irq in xhci_suspend()
xhci: Resume bus on any port status change.
commit 711669e5b8 fixed port 0 support
for i.MX51 but broke it for (at least) i.MX27 which doesn't have
a usb_phy1 clock but has a pdev->id 0.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Previously a check was done on an ID register at the base of a CPU's
internal USB registers to determine if system interface regsiters were
present. The check looked for an ID register that had the format
ID[0:5] == ~ID[8:13] as described in the MPC5121 User's Manual to
determine if a MPC5121 or MPC83xx/85xx was being used.
There are two issues with this method:
- The ID register is not defined on the MPC83xx/85xx CPUs, so its
unclear what is being checked on them.
- Newer CPUs such as the P4080 also don't document the ID register, but
do share the same format as the MPC5121. Thus the previous code did
not set 'have_sysif_regs' properly which results in the P4080 not
properly initializing its USB ports.
Using the device tree 'compatible' node is a cleaner way to determine if
'have_sysif_regs' should be set and resolves the USB initialization issue
seen on the P4080.
Tested on a P4080-based system and compile tested on mpc512x_defconfig
with Freescale EHCI driver enabled.
Cc: Anatolij Gustschin <agust@denx.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1440) fixes a bug in ehci-hcd. ehci->periodic_size is
used to compute the size in a dma_alloc_coherent() call, but then it
gets changed later on. As a result, the corresponding call to
dma_free_coherent() passes a different size from the original
allocation. Fix the problem by adjusting ehci->periodic_size before
carrying out any of the memory allocations.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
CC: David Brownell <david-b@pacbell.net>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
AMD Hudson also needs the same ASPM quirk as SB800
Signed-off-by: Alex He <alex.he@amd.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The unused space in the doorbell is now marked as RsvdZ, not RsvdP, so
we can avoid reading the doorbell before writing it.
Update the doorbell-related defines to produce the entire doorbell value
from a single macro. Document the doorbell format in a comment.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
dev_dbg() is used to print ordinary transfer messages in xhci-ring.c.
System log messages will be flushed if CONFIG_USB_DEBUG is set. Replace the
dev_dbg() with xhci_dbg().
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
giveback_first_trb() controls the cycle bit set of the start_trb, to ensure
that the start_trb is written last and the host controller will receive a
whole td at a time.
However, if the ring is wrapped and cycle bit is toggled to zero, then
giveback_first_trb() will be of no effect. In this case, set the cycle bit of
start_trb to 1 at the beginning and clear it in giveback_first_trb().
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Parameter *td is not used in giveback_first_trb(). Remove it.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Fix the more_trbs_coming field of queue_trb() in isoc transfer.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
When xhci_discover_or_reset_device() is called after a host controller
power loss, the virtual device may need to be reallocated. Make sure
xhci_alloc_dev() uses GFP_NOIO. This avoid causing a deadlock by allowing
the kernel to flush pending I/O while reallocating memory for a virtual
device for a USB mass storage device that's holding the backing store for
dirty memory buffers.
This patch should be queued for the 2.6.37 stable tree.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Synchronize the interrupts instead of free them in xhci_suspend(). This will
prevent a double free when the host is suspended and then the card removed.
Set the flag hcd->msix_enabled when using MSI-X, and check the flag in
suspend_common(). MSI-X synchronization will be handled by xhci_suspend(),
and MSI/INTx will be synchronized in suspend_common().
This patch should be queued for the 2.6.37 stable tree.
Reported-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
The original code that resumed the USB bus on a port status change would
only do so when there was a device connected to the port. If a device was
just disconnected, the event would be queued for khubd, but khubd wouldn't
run. That would leave the connect status change (CSC) bit set.
If a USB device was plugged into that same port, the xHCI host controller
would set the current connect status (CCS) bit. But since the CSC bit was
already set, it would not generate an interrupt for a port status change
event. That would mean the user could "Safely Remove" a device, have the
bus suspend, disconnect the device, re-plug it in, and then the device
would never be enumerated.
Plugging in a different device on another port would cause the bus to
resume, and khubd would notice the re-connected device. Running lsusb
would also resume the bus, leading users to report the problem "went away"
when using diagnostic tools.
The solution is to resume the bus when a port status change event is
received, regardless of the port status.
Thank you very much to Maddog for helping me track down this Heisenbug.
This patch should be queued for the 2.6.37 stable tree.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Jon 'maddog' Hall <maddog@li.org>
Tested-by: Andiry Xu <andiry.xu@amd.com>
Cc: stable@kernel.org
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (33 commits)
usb: don't use flush_scheduled_work()
speedtch: don't abuse struct delayed_work
media/video: don't use flush_scheduled_work()
media/video: explicitly flush request_module work
ioc4: use static work_struct for ioc4_load_modules()
init: don't call flush_scheduled_work() from do_initcalls()
s390: don't use flush_scheduled_work()
rtc: don't use flush_scheduled_work()
mmc: update workqueue usages
mfd: update workqueue usages
dvb: don't use flush_scheduled_work()
leds-wm8350: don't use flush_scheduled_work()
mISDN: don't use flush_scheduled_work()
macintosh/ams: don't use flush_scheduled_work()
vmwgfx: don't use flush_scheduled_work()
tpm: don't use flush_scheduled_work()
sonypi: don't use flush_scheduled_work()
hvsi: don't use flush_scheduled_work()
xen: don't use flush_scheduled_work()
gdrom: don't use flush_scheduled_work()
...
Fixed up trivial conflict in drivers/media/video/bt8xx/bttv-input.c
as per Tejun.
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (144 commits)
USB: add support for Dream Cheeky DL100B Webmail Notifier (1d34:0004)
USB: serial: ftdi_sio: add support for TIOCSERGETLSR
USB: ehci-mxc: Setup portsc register prior to accessing OTG viewport
USB: atmel_usba_udc: fix freeing irq in usba_udc_remove()
usb: ehci-omap: fix tll channel enable mask
usb: ohci-omap3: fix trivial typo
USB: gadget: ci13xxx: don't assume that PAGE_SIZE is 4096
USB: gadget: ci13xxx: fix complete() callback for no_interrupt rq's
USB: gadget: update ci13xxx to work with g_ether
USB: gadgets: ci13xxx: fix probing of compiled-in gadget drivers
Revert "USB: musb: pm: don't rely fully on clock support"
Revert "USB: musb: blackfin: pm: make it work"
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
...
Manually fix up trivial conflicts in USB Kconfig changes in:
arch/arm/mach-omap2/Kconfig
arch/sh/Kconfig
drivers/usb/Kconfig
drivers/usb/host/ehci-hcd.c
and annoying chip clock data conflicts in:
arch/arm/mach-omap2/clock3xxx_data.c
arch/arm/mach-omap2/clock44xx_data.c
The below patch fixes a typo "diable" to "disable" and also fixes another typo in a comment.
Please let me know if this is correct or not.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Current code doesn't really enable the usb clocks so if they're disabled
when booting linux, the kernel/machine will hang as soon as someone is trying
to read a usb register
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
flush_scheduled_work() is being deprecated. Directly flush or cancel
work items instead.
* u_ether, isp1301_omap, speedtch conversions are straight-forward.
* ochi-hcd should only flush when quirk_nec() is true as otherwise the
work wouldn't have been initialized.
* In oti6858, cancel_delayed_work() + flush_scheduled_work() ->
cancel_delayed_work_sync().
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Duncan Sands <duncan.sands@free.fr>
Cc: linux-usb@vger.kernel.org
This is to resolve the conflict in the file,
drivers/usb/gadget/composite.c that was due to a revert in Linus's tree
needed for the 2.6.37 release.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
In order to read/write to the i.MX OTG viewport register it is necessary to setup
the PORTSCx register first.
By default i.MX OTG port is configured for USB serial PHY. In order to use a ULPI PHY
the PORTSCx register needs to be configured properly.
commit 724c852 (USB: ehci/mxc: compile fix) placed the PORTSC setup after the OTG
viewport is accessed and this causes ULPI read/write to fail.
Revert the PORTSC setup order.
Tested on a MX31PDK board with a ISP1504 transceiver:
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
mxc-ehci mxc-ehci.0: initializing i.MX USB Controller
ULPI transceiver vendor/product ID 0x04cc/0x1504
Found NXP ISP1504 ULPI transceiver.
ULPI integrity check: passed.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The TLL channel enable code searches for the wrong mask, and
could end up enabling the wrong port. Fix this.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is the ohci-omap3 driver, not ehci-omap. Correct this
obvious typo.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb-next: (132 commits)
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
usb: gadget: f_ncm.c added
usb: gadget: u_ether: prepare for NCM
usb: pch_udc: Fix setup transfers with data out
usb: pch_udc: Fix compile error, warnings and checkpatch warnings
usb: add ab8500 usb transceiver driver
USB: gadget: Implement runtime PM for MSM bus glue driver
USB: gadget: Implement runtime PM for ci13xxx gadget
USB: gadget: Add USB controller driver for MSM SoC
USB: gadget: Introduce ci13xxx_udc_driver struct
USB: gadget: Initialize ci13xxx gadget device's coherent DMA mask
USB: gadget: Fix "scheduling while atomic" bugs in ci13xxx_udc
USB: gadget: Separate out PCI bus code from ci13xxx_udc
...
Enable runtime PM and mark no_callbacks flag. OTG device, parent of
HCD takes care of putting hardware into low power mode. Adjust port
power wakeup flags during system suspend and resume.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for EHCI compliant HSUSB Host controller found
on MSM chips. The root hub has a single port and TT is built into it.
This driver depends on OTG driver for PHY initialization, clock
management and powering up VBUS.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Matthieu CASTET