We shouldn't be using regulator_get_optional() here. These
regulators are always present as part of the physical design and
there isn't any way to use an internal regulator or change the
source of the reference voltage via software. Given that the only
users of this driver in the kernel are DT based, this change
should be transparent to them even if they don't specify any
supplies because the regulator framework will insert dummy
supplies as needed.
Cc: Nishanth Menon <nm@ti.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 70a640d0da
("net/mlx4_en: Use affinity hint") and commit
c8865b64b0 ("cpumask: Utility function
to set n'th cpu - local cpu first") because these changes break
the build when SMP is disabled amongst other things.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We shouldn't be using regulator_get_optional() here. These
regulators are always present as part of the physical design and
there isn't any way to use an internal regulator or change the
source of the reference voltage via software. Given that the only
users of this driver in the kernel are DT based, this change
should be transparent to them even if they don't specify any
supplies because the regulator framework will insert dummy
supplies as needed.
Cc: Nishanth Menon <nm@ti.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Users are currently just providing "ks8851" as the compatible for
this driver in device tree. Add a compatible string that provides
the vendor name along with the device name to be more explicit.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the ks8851 driver to enable an optional 1.8V vdd_io
regulator and assert the reset pin to the phy if a reset gpio is
present in device tree.
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simplifies error paths and removes the need to
regulator_put().
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Few platforms use external regulator to keep the ethernet MAC supplied.
So, request and enable the regulator for driver functionality.
Fixes: 66fda75f47 (regulator: core: Replace direct ops->disable usage)
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Suggested-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SIMPLE_DEV_PM_OPS macro can handle !CONFIG_PM_SLEEP case nicely, so there is no
need to define PM_OPS for both CONFIG_PM_SLEEP and !CONFIG_PM_SLEEP cases.
Remove the unneeded definitions.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dev_pm_ops instead of the deprecated legacy suspend/resume callbacks.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
By using module_spi_driver we can eliminate a few lines of boilerplate code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the Datasheet (page 52):
15-12 Reserved
11-0 RXBC Receive Byte Count
This field indicates the present received frame byte size.
The code has a bug:
rxh = ks8851_rdreg32(ks, KS_RXFHSR);
rxstat = rxh & 0xffff;
rxlen = rxh >> 16; // BUG!!! 0xFFF mask should be applied
Signed-off-by: Max Nekludov <Max.Nekludov@us.elster.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
just as it should have been. It also helps
removing the, now unnecessary, workqueue.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NET_ADDR_SET is set in dev_set_mac_address() no need to alter
dev->addr_assign_type value in drivers.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the existing uses of random_ether_addr to
the new eth_random_addr.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a link change interrupt comes in we just clear the interrupt
and continue along without notifying the upper networking layers
that the link has changed. Use the mii_check_link() function to
update the link status whenever a link change interrupt occurs.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_id parameter passed to free_irq needs to match the one passed
to the corresponding request_irq.
Signed-off-by: Matt Renzelmann <mjr@cs.wisc.edu>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a potential deadlock scenario when the ks8851 driver
is removed. The interrupt handler schedules a workqueue which
acquires a mutex that ks8851_net_stop() also acquires before
flushing the workqueue. Previously lockdep wouldn't be able
to find this problem but now that it has the support we can
trigger this lockdep warning by rmmoding the driver after
an ifconfig up.
Fix the possible deadlock by disabling the interrupts in
the chip and then release the lock across the workqueue
flushing. The mutex is only there to proect the registers
anyway so this should be ok.
=======================================================
[ INFO: possible circular locking dependency detected ]
3.0.21-00021-g8b33780-dirty #2911
-------------------------------------------------------
rmmod/125 is trying to acquire lock:
((&ks->irq_work)){+.+...}, at: [<c019e0b8>] flush_work+0x0/0xac
but task is already holding lock:
(&ks->lock){+.+...}, at: [<bf00b850>] ks8851_net_stop+0x64/0x138 [ks8851]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&ks->lock){+.+...}:
[<c01b89c8>] __lock_acquire+0x940/0x9f8
[<c01b9058>] lock_acquire+0x10c/0x130
[<c083dbec>] mutex_lock_nested+0x68/0x3dc
[<bf00bd48>] ks8851_irq_work+0x24/0x46c [ks8851]
[<c019c580>] process_one_work+0x2d8/0x518
[<c019cb98>] worker_thread+0x220/0x3a0
[<c01a2ad4>] kthread+0x88/0x94
[<c0107008>] kernel_thread_exit+0x0/0x8
-> #0 ((&ks->irq_work)){+.+...}:
[<c01b7984>] validate_chain+0x914/0x1018
[<c01b89c8>] __lock_acquire+0x940/0x9f8
[<c01b9058>] lock_acquire+0x10c/0x130
[<c019e104>] flush_work+0x4c/0xac
[<bf00b858>] ks8851_net_stop+0x6c/0x138 [ks8851]
[<c06b209c>] __dev_close_many+0x98/0xcc
[<c06b2174>] dev_close_many+0x68/0xd0
[<c06b22ec>] rollback_registered_many+0xcc/0x2b8
[<c06b2554>] rollback_registered+0x28/0x34
[<c06b25b8>] unregister_netdevice_queue+0x58/0x7c
[<c06b25f4>] unregister_netdev+0x18/0x20
[<bf00c1f4>] ks8851_remove+0x64/0xb4 [ks8851]
[<c049ddf0>] spi_drv_remove+0x18/0x1c
[<c0468e98>] __device_release_driver+0x7c/0xbc
[<c0468f64>] driver_detach+0x8c/0xb4
[<c0467f00>] bus_remove_driver+0xb8/0xe8
[<c01c1d20>] sys_delete_module+0x1e8/0x27c
[<c0105ec0>] ret_fast_syscall+0x0/0x3c
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&ks->lock);
lock((&ks->irq_work));
lock(&ks->lock);
lock((&ks->irq_work));
*** DEADLOCK ***
4 locks held by rmmod/125:
#0: (&__lockdep_no_validate__){+.+.+.}, at: [<c0468f44>] driver_detach+0x6c/0xb4
#1: (&__lockdep_no_validate__){+.+.+.}, at: [<c0468f50>] driver_detach+0x78/0xb4
#2: (rtnl_mutex){+.+.+.}, at: [<c06b25e8>] unregister_netdev+0xc/0x20
#3: (&ks->lock){+.+...}, at: [<bf00b850>] ks8851_net_stop+0x64/0x138 [ks8851]
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the ks8851_rdreg16 call above the call to request_irq and cache
the result for subsequent repeated use. A spurious interrupt may
otherwise cause a crash. Thanks to Stephen Boyd, Flavio Leitner, and
Ben Hutchings for feedback.
Signed-off-by: Matt Renzelmann <mjr@cs.wisc.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.c
Small minor conflict in bnx2x, wherein one commit changed how
statistics were stored in software, and another commit
fixed endianness bugs wrt. reading the values provided by
the chip in memory.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_hw_addr_random() instead of calling random_ether_addr()
to set addr_assign_type correctly to NET_ADDR_RANDOM.
Reset the state to NET_ADDR_PERM as soon as the MAC get
changed via .ndo_set_mac_address.
v2: adapt to renamed eth_hw_addr_random()
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fix a similar problem as in 72092cc453
and 481a819914 ("can:
fix NOHZ local_softirq_pending 08 warning"). This fix replaces netif_rx()
with netif_rx_ni() which has to be used from process/softirq context.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reorganization of the driver layout in drivers/net
left behind some stale paths in comments and in Kconfig
help text. Bring them up to date. No actual change to
any code takes place here.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool EEPROM read/write support using the eeprom_93cx6
library instead of open-coding the functions.
Depends on eeprom_93cx6 driver getting EEPROM write support.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
[sboyd@codeaurora.org: Removed previous eeprom implementation]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When device is off it is under power saving mode. Changing the MAC address
in that situation will result in the device not communicating as the first
write to the MAC address register is not executed.
Signed-off-by: Tristram Ha <Tristram.Ha@micrel.com>
[ben@simtec.co.uk: cleaned up header]
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for reading the MAC address from the system registers if there
is an EEPROM present. This involves caching the KS_CCR register for later
use (will also be useful for ETHTOOL support) and adding a print to say
that there is an EEPROM present.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the Micrel drivers into drivers/net/ethernet/micrel/ and
make the necessary Kconfig and Makefile changes.
CC: Ben Dooks <ben@simtec.co.uk>
CC: Tristram Ha <Tristram.Ha@micrel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Stephen Boyd