A address-only I2C_WRITE can't be replied with a short i2c ack, but I
suppose it could be replied with an i2c defer. So the code should be
prepared for an address-only I2C_WRITE_STATUS_UPDATE.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: "Terje Bergström" <tbergstrom@nvidia.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rename the I2C_STATUS request to I2C_WRITE_STATUS_UPDATE to match the
spec.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
When the DPAUX isn't attached to an SOR the interrupts are not useful.
This also prevents a race that could potentially cause a crash on driver
removal.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DPAUX code paths already configure the pads in AUX mode, but there
is no way to reconfigure them in I2C mode for HDMI (the DPAUX module is
unused in that case). Enabling the pads in I2C mode by default is the
quickest way to support HDMI. Eventually this may need an explicit call
in the user drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When probing the dpaux device fails, output proper error messages to
help diagnose the cause of the failure.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use a sized unsigned 32-bit data type (u32) to store register contents.
The DPAUX registers are 32 bits wide irrespective of the architecture's
data width.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DPAUX read/write FIFO registers aren't sequential in the register
space, causing transfers larger than 4 bytes to cause accesses to non-
existing FIFO registers.
Fixes: 6b6b604215 ("drm/tegra: Add eDP support")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rename the defines to have levels instead of values for vswing and
pre-emph levels as the values may differ in other scenarios like low vswing of
eDP1.4 where the values are different.
Done using following cocci patch for each define:
@@
@@
# define DP_TRAIN_VOLTAGE_SWING_400 (0 << 0)
+ # define DP_TRAIN_VOLTAGE_SWING_LEVEL_0 (0 << 0)
...
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When tegra-drm.ko is built as a module, these MODULE_DEVICE_TABLEs allow
the module to be auto-loaded since the module will match the devices
instantiated from device tree.
(Notes for stable: in 3.14+, just git rm any conflicting file, since they
are added in later kernels. For 3.13 and below, manual merging will be
needed)
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Doing so allows the hotplug events generated by the connector to be
properly handled by the DRM poll helpers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Calling the drm_helper_hpd_irq_event() helper can sleep, so instead of
invoking it directly from the interrupt handler, schedule a work queue
and run it from there.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This should avoid races between connector probing and HPD
irqs in the future, currently mode_config.mutex blocks this
possibility.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Certain types of I2C-over-AUX transactions require that only the address
is transferred. Detect this by looking at the AUX message's size and set
the address-only bit appropriately.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for eDP functionality found on Tegra124 and later SoCs. Only
fast link training is currently supported.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Ville Syrjälä