current_desc_hdr() returns a u32 but in fact this is a __be32,
leading to a lot of sparse warnings.
Change the return type to __be32 and ensure it is handled as
sure by the caller.
Fixes: 3e721aeb3d ("crypto: talitos - handle descriptor not found in error path")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
current_desc_hdr() compares the value of the current descriptor
with the next_desc member of the talitos_desc struct.
While the current descriptor is obtained from in_be32() which
return CPU ordered bytes, next_desc member is in big endian order.
Convert the current descriptor into big endian before comparing it
with next_desc.
This fixes a sparse warning.
Fixes: 37b5e8897e ("crypto: talitos - chain in buffered data for ahash on SEC1")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Replace commas with semicolons. What is done is essentially described by
the following Coccinelle semantic patch (http://coccinelle.lip6.fr/):
// <smpl>
@@ expression e1,e2; @@
e1
-,
+;
e2
... when any
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The CRYPTO_TFM_RES_BAD_KEY_LEN flag was apparently meant as a way to
make the ->setkey() functions provide more information about errors.
However, no one actually checks for this flag, which makes it pointless.
Also, many algorithms fail to set this flag when given a bad length key.
Reviewing just the generic implementations, this is the case for
aes-fixed-time, cbcmac, echainiv, nhpoly1305, pcrypt, rfc3686, rfc4309,
rfc7539, rfc7539esp, salsa20, seqiv, and xcbc. But there are probably
many more in arch/*/crypto/ and drivers/crypto/.
Some algorithms can even set this flag when the key is the correct
length. For example, authenc and authencesn set it when the key payload
is malformed in any way (not just a bad length), the atmel-sha and ccree
drivers can set it if a memory allocation fails, and the chelsio driver
sets it for bad auth tag lengths, not just bad key lengths.
So even if someone actually wanted to start checking this flag (which
seems unlikely, since it's been unused for a long time), there would be
a lot of work needed to get it working correctly. But it would probably
be much better to go back to the drawing board and just define different
return values, like -EINVAL if the key is invalid for the algorithm vs.
-EKEYREJECTED if the key was rejected by a policy like "no weak keys".
That would be much simpler, less error-prone, and easier to test.
So just remove this flag.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Commit 7a7ffe65c8 ("crypto: skcipher - Add top-level skcipher interface")
dated 20 august 2015 introduced the new skcipher API which is supposed to
replace both blkcipher and ablkcipher. While all consumers of the API have
been converted long ago, some producers of the ablkcipher remain, forcing
us to keep the ablkcipher support routines alive, along with the matching
code to expose [a]blkciphers via the skcipher API.
So switch this driver to the skcipher API, allowing us to finally drop the
ablkcipher code in the near future.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When VMAP_STACK is selected, stack cannot be DMA-mapped.
Therefore, the hash result has to be DMA-mapped in the request
context and copied into areq->result at completion.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add missing break statement in order to prevent the code from falling
through to case CRYPTO_ALG_TYPE_AHASH.
Fixes: aeb4c132f3 ("crypto: talitos - Convert to new AEAD interface")
Cc: stable@vger.kernel.org
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch removes the variable flags which is now unused thanks
to the new DES helpers.
Fixes: 9d574ae8eb ("crypto: talitos/des - switch to new...")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 5.3:
API:
- Test shash interface directly in testmgr
- cra_driver_name is now mandatory
Algorithms:
- Replace arc4 crypto_cipher with library helper
- Implement 5 way interleave for ECB, CBC and CTR on arm64
- Add xxhash
- Add continuous self-test on noise source to drbg
- Update jitter RNG
Drivers:
- Add support for SHA204A random number generator
- Add support for 7211 in iproc-rng200
- Fix fuzz test failures in inside-secure
- Fix fuzz test failures in talitos
- Fix fuzz test failures in qat"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (143 commits)
crypto: stm32/hash - remove interruptible condition for dma
crypto: stm32/hash - Fix hmac issue more than 256 bytes
crypto: stm32/crc32 - rename driver file
crypto: amcc - remove memset after dma_alloc_coherent
crypto: ccp - Switch to SPDX license identifiers
crypto: ccp - Validate the the error value used to index error messages
crypto: doc - Fix formatting of new crypto engine content
crypto: doc - Add parameter documentation
crypto: arm64/aes-ce - implement 5 way interleave for ECB, CBC and CTR
crypto: arm64/aes-ce - add 5 way interleave routines
crypto: talitos - drop icv_ool
crypto: talitos - fix hash on SEC1.
crypto: talitos - move struct talitos_edesc into talitos.h
lib/scatterlist: Fix mapping iterator when sg->offset is greater than PAGE_SIZE
crypto/NX: Set receive window credits to max number of CRBs in RxFIFO
crypto: asymmetric_keys - select CRYPTO_HASH where needed
crypto: serpent - mark __serpent_setkey_sbox noinline
crypto: testmgr - dynamically allocate crypto_shash
crypto: testmgr - dynamically allocate testvec_config
crypto: talitos - eliminate unneeded 'done' functions at build time
...
icv_ool is not used anymore, drop it.
Fixes: e345177ded ("crypto: talitos - fix AEAD processing.")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
On SEC1, hash provides wrong result when performing hashing in several
steps with input data SG list has more than one element. This was
detected with CONFIG_CRYPTO_MANAGER_EXTRA_TESTS:
[ 44.185947] alg: hash: md5-talitos test failed (wrong result) on test vector 6, cfg="random: may_sleep use_finup src_divs=[<reimport>25.88%@+8063, <flush>24.19%@+9588, 28.63%@+16333, <reimport>4.60%@+6756, 16.70%@+16281] dst_divs=[71.61%@alignmask+16361, 14.36%@+7756, 14.3%@+"
[ 44.325122] alg: hash: sha1-talitos test failed (wrong result) on test vector 3, cfg="random: inplace use_final src_divs=[<flush,nosimd>16.56%@+16378, <reimport>52.0%@+16329, 21.42%@alignmask+16380, 10.2%@alignmask+16380] iv_offset=39"
[ 44.493500] alg: hash: sha224-talitos test failed (wrong result) on test vector 4, cfg="random: use_final nosimd src_divs=[<reimport>52.27%@+7401, <reimport>17.34%@+16285, <flush>17.71%@+26, 12.68%@+10644] iv_offset=43"
[ 44.673262] alg: hash: sha256-talitos test failed (wrong result) on test vector 4, cfg="random: may_sleep use_finup src_divs=[<reimport>60.6%@+12790, 17.86%@+1329, <reimport>12.64%@alignmask+16300, 8.29%@+15, 0.40%@+13506, <reimport>0.51%@+16322, <reimport>0.24%@+16339] dst_divs"
This is due to two issues:
- We have an overlap between the buffer used for copying the input
data (SEC1 doesn't do scatter/gather) and the chained descriptor.
- Data copy is wrong when the previous hash left less than one
blocksize of data to hash, implying a complement of the previous
block with a few bytes from the new request.
Fix it by:
- Moving the second descriptor after the buffer, as moving the buffer
after the descriptor would make it more complex for other cipher
operations (AEAD, ABLKCIPHER)
- Skip the bytes taken from the new request to complete the previous
one by moving the SG list forward.
Fixes: 37b5e8897e ("crypto: talitos - chain in buffered data for ahash on SEC1")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Moves struct talitos_edesc into talitos.h so that it can be used
from any place in talitos.c
It will be required for next patch ("crypto: talitos - fix hash
on SEC1")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When building for SEC1 only, talitos2_done functions are unneeded
and should go away.
For this, use has_ftr_sec1() which will always return true when only
SEC1 support is being built, allowing GCC to drop TALITOS2 functions.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Below commit came with a typo in the CONFIG_ symbol, leading
to a permanently reduced max key size regarless of the driver
capabilities.
Reported-by: Horia Geantă <horia.geanta@nxp.com>
Fixes: b8fbdc2bc4 ("crypto: talitos - reduce max key size for SEC1")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch drops the license text and replaces it
with an SPDX-License-Identifier tag.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There is no other file using talitos_submit in the kernel tree,
so it doesn't need to be exported nor made global.
This reverts commit 865d506155.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 865d506155 ("crypto: talitos - export the talitos_submit function")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This driver is working well in 'simple cases', but as soon as
more exotic SG lists are provided (dst different from src,
auth part not in a single SG fragment, ...) there are
wrong results, overruns, etc ...
This patch cleans up the AEAD processing by:
- Simplifying the location of 'out of line' ICV
- Never using 'out of line' ICV on encryp
- Always using 'out of line' ICV on decrypt
- Forcing the generation of a SG table on decrypt
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: aeb4c132f3 ("crypto: talitos - Convert to new AEAD interface")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The MPC885 reference manual states:
SEC Lite-initiated 8xx writes can occur only on 32-bit-word boundaries, but
reads can occur on any byte boundary. Writing back a header read from a
non-32-bit-word boundary will yield unpredictable results.
In order to ensure that, cra_alignmask is set to 3 for SEC1.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 9c4a79653b ("crypto: talitos - Freescale integrated security engine (SEC) driver")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The driver assumes that the ICV is as a single piece in the last
element of the scatterlist. This assumption is wrong.
This patch ensures that the ICV is properly handled regardless of
the scatterlist layout.
Fixes: 9c4a79653b ("crypto: talitos - Freescale integrated security engine (SEC) driver")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In that mode, hardware ICV verification is not supported.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 7405c8d7ff ("crypto: talitos - templates for AEAD using HMAC_SNOOP_NO_AFEU")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For decrypt, req->cryptlen includes the size of the authentication
part while all functions of the driver expect cryptlen to be
the size of the encrypted data.
As it is not expected to change req->cryptlen, this patch
implements local calculation of cryptlen.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 9c4a79653b ("crypto: talitos - Freescale integrated security engine (SEC) driver")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When data size is not a multiple of the alg's block size,
the SEC generates an error interrupt and dumps the registers.
And for NULL size, the SEC does just nothing and the interrupt
is awaited forever.
This patch ensures the data size is correct before submitting
the request to the SEC engine.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 4de9d0b547 ("crypto: talitos - Add ablkcipher algorithms")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
CTR has a blocksize of 1.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 5e75ae1b3c ("crypto: talitos - add new crypto modes")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Although the HW accepts any size and silently truncates
it to the correct length, the extra tests expects EINVAL
to be returned when the key size is not valid.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 4de9d0b547 ("crypto: talitos - Add ablkcipher algorithms")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
SEC1 doesn't support SHA384/512, so it doesn't require
longer keys.
This patch reduces the max key size when the driver
is built for SEC1 only.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 03d2c5114c ("crypto: talitos - Extend max key length for SHA384/512-HMAC and AEAD")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The talitos driver has two ways to perform AEAD depending on the
HW capability. Some HW support both. It is needed to give them
different names to distingish which one it is for instance when
a test fails.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 7405c8d7ff ("crypto: talitos - templates for AEAD using HMAC_SNOOP_NO_AFEU")
Cc: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Selftests report the following:
[ 2.984845] alg: skcipher: cbc-aes-talitos encryption test failed (wrong output IV) on test vector 0, cfg="in-place"
[ 2.995377] 00000000: 3d af ba 42 9d 9e b4 30 b4 22 da 80 2c 9f ac 41
[ 3.032673] alg: skcipher: cbc-des-talitos encryption test failed (wrong output IV) on test vector 0, cfg="in-place"
[ 3.043185] 00000000: fe dc ba 98 76 54 32 10
[ 3.063238] alg: skcipher: cbc-3des-talitos encryption test failed (wrong output IV) on test vector 0, cfg="in-place"
[ 3.073818] 00000000: 7d 33 88 93 0f 93 b2 42
This above dumps show that the actual output IV is indeed the input IV.
This is due to the IV not being copied back into the request.
This patch fixes that.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
CRYPTO_TFM_REQ_WEAK_KEY confuses newcomers to the crypto API because it
sounds like it is requesting a weak key. Actually, it is requesting
that weak keys be forbidden (for algorithms that have the notion of
"weak keys"; currently only DES and XTS do).
Also it is only one letter away from CRYPTO_TFM_RES_WEAK_KEY, with which
it can be easily confused. (This in fact happened in the UX500 driver,
though just in some debugging messages.)
Therefore, make the intent clear by renaming it to
CRYPTO_TFM_REQ_FORBID_WEAK_KEYS.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch moves the mapping of IV after the kmalloc(). This
avoids having to unmap in case kmalloc() fails.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Remove dead code related to internal IV generators, which are no longer
used since they've been replaced with the "seqiv" and "echainiv"
templates. The removed code includes:
- The "givcipher" (GIVCIPHER) algorithm type. No algorithms are
registered with this type anymore, so it's unneeded.
- The "const char *geniv" member of aead_alg, ablkcipher_alg, and
blkcipher_alg. A few algorithms still set this, but it isn't used
anymore except to show via /proc/crypto and CRYPTO_MSG_GETALG.
Just hardcode "<default>" or "<none>" in those cases.
- The 'skcipher_givcrypt_request' structure, which is never used.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Some ahash algorithms set .cra_type = &crypto_ahash_type. But this is
redundant with the C structure type ('struct ahash_alg'), and
crypto_register_ahash() already sets the .cra_type automatically.
Apparently the useless assignment has just been copy+pasted around.
So, remove the useless assignment from all the ahash algorithms.
This patch shouldn't change any actual behavior.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Many ahash algorithms set .cra_flags = CRYPTO_ALG_TYPE_AHASH. But this
is redundant with the C structure type ('struct ahash_alg'), and
crypto_register_ahash() already sets the type flag automatically,
clearing any type flag that was already there. Apparently the useless
assignment has just been copy+pasted around.
So, remove the useless assignment from all the ahash algorithms.
This patch shouldn't change any actual behavior.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In talitos's aead_setkey we save pointers to the authenc keys in a
local variable of type struct crypto_authenc_keys and we don't
zeroize it after use. Fix this and don't leak pointers to the
authenc keys.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For SEC 2.x+, cipher in length must contain only the ciphertext length.
In case of using hardware ICV checking, the ICV length is provided via
the "extent" field of the descriptor pointer.
Cc: <stable@vger.kernel.org> # 4.8+
Fixes: 549bd8bc59 ("crypto: talitos - Implement AEAD for SEC1 using HMAC_SNOOP_NO_AFEU")
Reported-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Tested-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
req_ctx->hw_context is mainly used only by the HW. So it is not needed
to sync the HW and the CPU each time hw_context in DMA mapped.
This patch modifies the DMA mapping in order to limit synchronisation
to necessary situations.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Commit 49f9783b0c ("crypto: talitos - do hw_context DMA mapping
outside the requests") introduced a persistent dma mapping of
req_ctx->hw_context
Commit 37b5e8897e ("crypto: talitos - chain in buffered data for ahash
on SEC1") introduced a persistent dma mapping of req_ctx->buf
As there is no destructor for req_ctx (the request context), the
associated dma handlers where set in ctx (the tfm context). This is
wrong as several hash operations can run with the same ctx.
This patch removes this persistent mapping.
Reported-by: Horia Geanta <horia.geanta@nxp.com>
Cc: <stable@vger.kernel.org>
Fixes: 49f9783b0c ("crypto: talitos - do hw_context DMA mapping outside the requests")
Fixes: 37b5e8897e ("crypto: talitos - chain in buffered data for ahash on SEC1")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Tested-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The talitos driver starts several async crypto ops and waits for their
completions. Move it over to generic code doing the same.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Tested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch avoids copy of buffered data to hash from bufnext to buf
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
SEC1 doesn't support S/G in descriptors so for hash operations,
the CPU has to build a buffer containing the buffered block and
the incoming data. This generates a lot of memory copies which
represents more than 50% of CPU time of a md5sum operation as
shown below with a 'perf record'.
|--86.24%-- kcapi_md_digest
| |
| |--86.18%-- _kcapi_common_vmsplice_chunk_fd
| | |
| | |--83.68%-- splice
| | | |
| | | |--83.59%-- ret_from_syscall
| | | | |
| | | | |--83.52%-- sys_splice
| | | | | |
| | | | | |--83.49%-- splice_from_pipe
| | | | | | |
| | | | | | |--83.04%-- __splice_from_pipe
| | | | | | | |
| | | | | | | |--80.67%-- pipe_to_sendpage
| | | | | | | | |
| | | | | | | | |--78.25%-- hash_sendpage
| | | | | | | | | |
| | | | | | | | | |--60.08%-- ahash_process_req
| | | | | | | | | | |
| | | | | | | | | | |--56.36%-- sg_copy_buffer
| | | | | | | | | | | |
| | | | | | | | | | | |--55.29%-- memcpy
| | | | | | | | | | | |
However, unlike SEC2+, SEC1 offers the possibility to chain
descriptors. It is therefore possible to build a first descriptor
pointing to the buffered data and a second descriptor pointing to
the incoming data, hence avoiding the memory copy to a single
buffer.
With this patch, the time necessary for a md5sum on a 90Mbytes file
is approximately 3 seconds. Without the patch it takes 6 seconds.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
At every request, we map and unmap the same hash hw_context.
This patch moves the dma mapping/unmapping in functions ahash_init()
and ahash_import().
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
dma_map_single() is an heavy operation which doesn't need to
be done at each request as the key doesn't change.
Instead of DMA mapping the key at every request, this patch maps it
once in setkey()
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>