For RK3399, the phy_cfg_clk is a required clock, if phy_cfg_clk is
disabled, MIPI phy can not work. Let's return a error if there is no
phy_cfg_clk in dts property, when the pdata match RK3399.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1490147691-4489-2-git-send-email-zyw@rock-chips.com
Currently we are adding all components from the dts, if one of their
drivers been disabled, we would not be able to bring up others.
Refactor component match logic, follow exynos drm.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1490152880-21855-1-git-send-email-jeffy.chen@rock-chips.com
The vopb/vopl switch register of RK3399 mipi is different from RK3288,
the default setting for mipi dsi mode is different too, so add a
of_device_id structure to distinguish them, and make sure set the
correct mode before mipi phy init.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1487577744-2855-3-git-send-email-zyw@rock-chips.com
In order to fully reset the state of the MIPI controller we must assert
this reset.
This is slightly more complicated than it could be in order to maintain
compatibility with device trees that do not specify the reset property.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-24-john@metanate.com
This ensures that the output resolution is known before fbcon loads.
mipi_dsi_host_register() is moved above dw_mipi_dsi_register() to
simplify error cleanup since the order of these operations does not
matter.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-22-john@metanate.com
As the documentation for readx_poll_timeout says, we want to use the
specialized macro for readl rather than using the generic version
directly.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-19-john@metanate.com
The multiplication ratio for the PLL is required to be even due to the
use of a "by 2 pre-scaler". Currently we are likely to end up with an
odd multiplier even though there is an equivalent set of parameters with
an even multiplier.
For example, using the 324MHz bit rate with a reference clock of 24MHz
we end up with M = 27, N = 2 whereas the example in the PHY databook
gives M = 54, N = 4 for this bit rate and reference clock.
By walking down through the available multiplier instead of up we are
more likely to hit an even multiplier. With the above example we do now
get M = 54, N = 4 as given by the databook.
While doing this, change the loop limits to encode the actual limits on
the divisor, which are:
40MHz >= (pllref / N) >= 5MHz
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-18-john@metanate.com
These values are specified as constant time periods but the PHY
configuration is in terms of the current lane byte clock so using
constant values guarantees that the timings will be outside the
specification with some display configurations.
Derive the necessary configuration from the byte clock in order to
ensure that the PHY configuration is correct.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-17-john@metanate.com
Also don't power up the DSI host at this point since this is not
necessary in order to configure the PHY and we do so later when
selecting video or command mode.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-15-john@metanate.com
This clock rate is derived from the PHY PLL, so it should be calculated
dynamically. This calculation is the same as that used by the vendor
kernel and ensures that the escape clock runs at <20MHz as required by
the MIPI specification.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-14-john@metanate.com
Panel drivers may want to sent commands during the disable function, for
example MIPI_DCS_SET_DISPLAY_OFF before the video signal ends. In order
to send commands we need to write to registers, so pclk must be enabled.
While changing this, remove the unnecessary code after the panel
unprepare call which seems to be a workaround for a specific panel and
thus belongs in the panel driver.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-13-john@metanate.com
Some panels need to be configured with commands sent over the MIPI link,
which they will do in the prepare hook. Call this after the PHY has
been initialized so that we are able to send commands to the panel.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-12-john@metanate.com
By dereferencing the MIPI command buffer as a u32* we rely on it being
correctly aligned on ARM, but this may not be the case. Copy it into a
stack variable that will be correctly aligned.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-11-john@metanate.com
Requesting the HS clock from the PHY before we initialize it causes an
invalid signal to be sent out since the input clock is not yet
configured. The PHY databook suggests only asserting this signal when
performing HS transfers, so let's do that.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-10-john@metanate.com
Instead of always sending commands in LP mode, respect the
MIPI_DSI_MSG_USE_LPM flag to decide how to send each message. Also
request acks if MIPI_DSI_MSG_REQ_ACK is set.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-9-john@metanate.com
We want to check that both the GEN_CMD_EMPTY and GEN_PLD_W_EMPTY bits
are set so we can't just check "val & mask" because that will be true if
either bit is set.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-6-john@metanate.com
In a couple of places here we use "val" for the value that is about to
be written to a register but then reuse the same variable for the value
of a status register before we get around to writing it. Rename the
value to be written to so that we write the value we intend to and not
what we have just read from the status register.
Signed-off-by: John Keeping <john@metanate.com>
Tested-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-5-john@metanate.com
This is not needed since we can access the mode via the CRTC from the
enable hook. Also remove the "mode" field that is no longer used.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-4-john@metanate.com
This shows that we only use the mode from the enable function and
prepares us to remove the "mode" field and the mode_set hook in the next
commit.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-3-john@metanate.com
With atomic modesetting the hardware will be powered off when the
mode_set function is called. We should configure the hardware in the
enable function, which is the atomic version of "commit" so let's use
the enable hook rather than commit while we're at it.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-2-john@metanate.com
Many drivers (21 to be exact) create connectors that are always
connected (for instance to an LVDS or DSI panel). Instead of forcing
them to implement a dummy .detect() handler, make the callback optional
and consider the connector as always connected in that case.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Vincent Abriou <vincent.abriou@st.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[seanpaul fixed small conflict in rcar-du/rcar_du_lvdscon.c]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
We need to take care of the vop status when use
rockchip_drm_crtc_mode_config, if vop is disabled,
the function would failed, that is terrible.
Save output_type and output_mode into rockchip_crtc_state,
it's nice to make them into atomic.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Tested-by: John Keeping <john@metanate.com>
- Add and make use of drm_of_active_endpoint helpers
- Silence a noisy dev_info into a dev_dbg
- Stop touching primary fb on pageflips
- Track flip state explicitly
- Keep GEM buffer objects referenced while scanout is active
- Implement fence sync by deferring flips to a workqueue for
dma-bufs with pending fences
- Actually disable vblank IRQs while they are not needed
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ufbY
-----END PGP SIGNATURE-----
Merge tag 'imx-drm-next-20160301' of git://git.pengutronix.de/git/pza/linux into drm-next
imx-drm vblank IRQ control, fence support, and of endpoint helpers
- Add and make use of drm_of_active_endpoint helpers
- Silence a noisy dev_info into a dev_dbg
- Stop touching primary fb on pageflips
- Track flip state explicitly
- Keep GEM buffer objects referenced while scanout is active
- Implement fence sync by deferring flips to a workqueue for
dma-bufs with pending fences
- Actually disable vblank IRQs while they are not needed
* tag 'imx-drm-next-20160301' of git://git.pengutronix.de/git/pza/linux:
drm/imx: only enable vblank IRQs when needed
drm/imx: implement fence sync
drm/imx: keep GEM object referenced as long as scanout is active
drm/imx: track flip state explicitly
drm/imx: don't touch primary fb on pageflip
drm/imx: ipuv3 plane: Replace dev_info with dev_dbg if a plane's CRTC changes
gpu: ipu-v3: ipu-dc: Simplify display controller microcode setup
drm/rockchip: remove rockchip_drm_encoder_get_mux_id
drm/imx: remove imx_drm_encoder_get_mux_id
drm: add drm_of_encoder_active_endpoint helpers
It is replaced by drm_of_encoder_active_endpoint_id.
Suggested-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Yakir Yang <ykk@rock-chips.com>
[for dw_hdmi-rockchip]
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The function can return negative value so it should be assigned to signed
variable.
The problem has been detected using patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Add support for Synopsys DesignWare MIPI DSI controller which is
embedded in the rk3288 SoCs.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Chris Zhong