Tegra124 contains a similar set of audio devices to previous Tegra chips.
Specifically, there is an AHUB device which contains DMA FIFOs and audio
routing, and which hosts various audio-related components such as I2S
controllers.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Enable all the I2C controllers that are wired up on Venice2. I don't
know the correct I2C bus clock rates, so set them all to a conservative
100KHz for now.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tegra124 has 6 I2C controllers. The first 5 have identical configuration
to Tegra114, but the sixth obviously has different interrupt/... IDs.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tegra124 has 4 MMC controllers just like previous versions of the SoC.
Note that there are some non-backwards-compatible HW differences, and
hence a new DT compatible value must be used to describe the HW.
Also enable the relevant controllers in the Venice2 board DT.
power-gpios property suggested by Thierry Reding.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Instantiate the APB DMA controller in the Tegra124 DT, and add all
DMA-related properties to other DT nodes that rely on (reference) the
DMA controller's node.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
The DT bindings now require module resets to be specified. The earlier
patches which added these nodes were originally written before that
requirement.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
This patch adds clock properties for devices in the DT for basic support
of Tegra124 SoC.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
[swarren, added missing unit address to "clock" node]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
For Tegra DT files, I've been attempting to keep the nodes sorted in
the order:
1) Nodes with reg, in order of reg.
2) Nodes without reg, alphabetically.
This patch fixes a few escapees that I missed:-(
The diffs look larger than they really are, because sometimes when one
node was moved up or down, diff chose to represent this as many other
nodes being moved the other way!
Signed-off-by: Stephen Warren <swarren@nvidia.com>
DT node names should include a unit address iff the node has a reg
property. For Tegra DTs at least, we were previously applying a different
rule, namely that node names only needed to include a unit address if it
was required to make the node name unique. Consequently, many unit
addresses are missing. Add them.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The A13-OLinuXino-MICRO is a small dev-board with the Allwinner A13 SoC:
https://www.olimex.com/Products/OLinuXino/A13/A13-OLinuXino-MICRO/
Features:
A13 Cortex A8 processor at 1GHz, 3D Mali400 GPU
256 MB RAM (128Mbit x 16)
5VDC input power supply with own ICs, noise immune design
1 USB host
1 USB OTG which can power the board
SD-card connector for booting the Linux image
VGA video output
LCD signals available on connector so you still can use LCD if you disable VGA/HDMI
Audio output
Microphone input pads (no connector)
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Fix the name as per DT node naming convention.
- rename the node to syscon which is a more generic name.
- append the register value to the node name.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The minimum recommended ARM voltage for Exynos5250 at 200MHz
on Arndale board is 0.9125V. Update accordingly.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Exynos5420 is octa-core SoC from Samsung.
Hence populate all the CPU node entries.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Exynos5420 is octa-core SoC from Samsung. Hence extend exynos-mct clocksource
driver to support 8 local interrupts.
Also extend dts entries for 8 interrupts.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Adds G-Scaler device nodes to the DT device list
Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds the mmc device tree node entries for exynos5420 SOC.
Exynos5420 has a different version of DWMMC controller,so a new
compatible string is used to distinguish it from the prior SOC's.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch rename's the device tree mmc node's from "dwmmc" to "mmc".
According to ePAPR chapter 2.2.2 generic node name recommendation,
it has been opted change from dwmmc to mmc.Also this patch remove the
instance index from the node name.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
As fifo-depth property in dw_mmc device tree node is SOC
specific, move this property to exynos5250 SOC specific
file.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
[kgene.kim@samsung.com: squashed fifo-depth patch for cros5250-common]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
As per the timing information for supported panel, the value should
be between 47.2 MHz to 47.9 MHz for 60Hz refresh rate.
Total horizontal pixels = 1024 (x-res) + 80 (margin) + 48 (hsync) = 1152
Total vertical pixels = 600 (y-res) + 80 (margin) + 3 (vsync) = 683
Target pixel clock rate for refresh rate @60 Hz
= 1152 * 683 * 60 = 47208960 Hz ~ 47.5 MHz
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
As per the timing information for supported panel, the value should
be between 47.2 MHz to 47.9 MHz for 60Hz refresh rate.
Total horizontal pixels = 1024 (x-res) + 80 (margin) + 48 (hsync) = 1152
Total vertical pixels = 600 (y-res) + 80 (margin) + 3 (vsync) = 683
Target pixel clock rate for refresh rate @60 Hz
= 1152 * 683 * 60 = 47208960 Hz ~ 47.5 MHz
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
According to ePAPR, chapter 2.3.4, the status property has
defined that it should be set to "disabled" when "the device
is not presently operational, but it might become operational
in the future".
So this patch disable dwmmc node by "status = disabled" in SOC
dts file and enable dwmmc node by "status = okay" in board specific
dts file.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add GPIO DT node and pinmux entries for DA850 EVM. GPIO is
configurable differently on different boards. So add GPIO
pinmuxing in dts file.
Signed-off-by: KV Sujith <sujithkv@ti.com>
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This adds very basic device tree files for the Marvell Armada
1500-mini SoC (Berlin BG2CD) and the Google Chromecast. Currently,
SoC only has nodes for cpu, some clocks, l2 cache controller, local
timer, apb timers, uart, and interrupt controllers.
The Google Chromecast is a consumer device comprising the Armada
1500-mini SoC above.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This adds very basic device tree files for the Marvell Armada 1500 SoC
(Berlin BG2) and the Sony NSZ-GS7 GoogleTV board. Currently, SoC only has
nodes for cpus, some clocks, l2 cache controller, local timer, apb timers,
uart, and interrupt controllers. The Sony NSZ-GS7 is a GoogleTV consumer
device comprising the Armada 1500 SoC above.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jisheng Zhang <jszhang@marvell.com>
To be able to enable SDR12|25 for SD-cards, we needed to fixup the
configuration in DT of the gpio regulator, which handles the signal
voltage level. Some configuration were missing and some were wrong.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove duplicated configurations and move specific details into
each corresponding dtsi file for the href versions.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Added device tree support for TI's Keystone USB driver and updated the
Documentation with device tree binding information.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Added device tree support for TI's Keystone USB PHY driver and updated the
Documentation with device tree binding information.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Update the Keystone gic device tree entry to add the maintenance
interrupt information.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Update the Keystone gic node to add the GICV and GIGH address space
needed by the KVM.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
PA subsystem has a fixed factor clock at the input which is
input clock divided by 3. This patch adds this clock node to dts
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This patch adds K2 Kepler/Hawking evm (k2hk-evm) specific dts file.
To enable re-use of bindings across multiple evms of this family,
rename current keystone.dts to keystone.dtsi and include it in the
evm specific dts file.
K2 SoC has separate ref clock inputs for various clocks. So add
separate ref clock nodes for ARM, DDR3A, DDR3B and PA PLL input
clocks in k2hk-evm.dts. While at it, rename refclkmain to
refclksys based on device User Guide naming convention
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Marvell's Armada 370 Reference Design has a NAND flash, so enable it in
the devicetree and add the partitions as prepared in the factory images.
In order to skip the driver's custom device detection and use only ONFI
detection, the "marvell,keep-config" parameter is used. This is needed
because we have no support for setting the timings parameters yet.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The board has 7 buttons connected to GPIOs, add a corresponding
gpio-keys device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch support FSI-AK4648 with simple audio card
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a 'cpus' node to describe the CPU cores of Zynq.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The bindings for the TTC changed in commit 'arm: zynq: Use standard
timer binding' (e932900a32). That change
removed possible subnodes from this driver rendering the 'clock-ranges'
property invalid for this node.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The zynq includes a Cadence GEM IP core. This is compatible with the macb driver.
Add it to the zynq-7000 DT.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Josh Cartwright <josh.cartwright@ni.com>
[soren: rebased to current Linus tree, added zc706 + zed support, moved phy-mode property to board level dtses]
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Allwinner A31 uses the ARM GIC as its internal interrupts controller. The
GIC can work on several interrupt triggers, and the A31 was actually setting it
up to use a rising edge as a trigger, while it was actually a level high
trigger, leading to some interrupts that would be completely ignored if the
edge was missed.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable@vger.kernel.org # 3.12+
Signed-off-by: Olof Johansson <olof@lixom.net>
The Allwinner A20 uses the ARM GIC as its internal interrupts controller. The
GIC can work on several interrupt triggers, and the A20 was actually setting it
up to use a rising edge as a trigger, while it was actually a level high
trigger, leading to some interrupts that would be completely ignored if the
edge was missed.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable@vger.kernel.org #3.12+
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds PWM nodes for each of the four channels present on the
pxa270.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Now that all Tegra drivers have been converted to use DMA APIs which
retrieve DMA channel information from standard DMA DT properties, we can
remove all the legacy DT DMA-related properties.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Now that all Tegra drivers have been converted to use the common reset
framework, we can remove all the legacy DT clocks/clock-names entries for
"clocks" that were only used with the old custom Tegra module reset API.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
This patch switches the Tegra DT files to use the standard DMA DT bindings
rather than custom properties. Note that the legacy properties are not yet
removed; the drivers must be updated to use the new properties first.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
An earlier patch updated the Tegra DT bindings to require resets and
reset-names properties to be filled in. This patch updates the DT files
to include those properties.
Note that any legacy clocks and clock-names entries that are replaced by
reset properties are not yet removed; the drivers must be updated to use
the new resets and reset-names properties first.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Many of the Tegra DT binding documents say nothing about the clocks or
clock-names properties, yet those are present and required in DT files.
This patch simply updates the documentation file to match the implicit
definition of the binding, based on real-world DT content.
All Tegra bindings that mention clocks are updated to have consistent
wording and formatting of the clock-related properties.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-By: Terje Bergstrom <tbergstrom@nvidia.com>
Added missing clock frequency property to CPU node to avoid
boot time warnings.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Though the default value is 1, add it explicitly to avoid
unnecessary boot warnings and for consistency.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
- Delete some static core module mappings.
- Move EBI location to the device tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=efPU
-----END PGP SIGNATURE-----
Merge tag 'integrator-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/dt
From Linus Walleij:
Two integrator device tree patches for v3.14:
- Delete some static core module mappings.
- Move EBI location to the device tree.
* tag 'integrator-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: integrator: move EBI to the device tree
ARM: integrator: delete static core module mappings
Signed-off-by: Kevin Hilman <khilman@linaro.org>
The Allwinner A20 has support for four high speed timers. Apart for the
number of timers (4 vs 2), it's basically the same logic than the high
speed timers found in the sun5i chips.
Now that we have a driver to support it, we can enable them in the
device tree.
[dlezcano] : Fixed conflict with 428abbb8 "Enable the I2C controllers"
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The Allwinner A13 has support for two high speed timers. Now that we
have a driver to support it, we can enable them in the device tree.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The Allwinner A10s has support for two high speed timers. Now that we
have a driver to support it, we can enable them in the device tree.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
- many little corrections and documentation updates
- LCD FB Device Tree for at91sam9263 and at91sam9g45 boards
- crypto peripherals DT entries + DMA specification
- new Cosino board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJSpd+hAAoJEAf03oE53VmQB7cH+wVFP2N7+kGTB9WTBFOmTt/6
tAEyO/yUTGPZiDV1Vsb5F+MPi+de3pt0t9Br11bXSDolzwHPDMhcGXCDxpJlyYrN
sIGXO2YtUmIo+QMqShRXOgoozkGqXxpOqVt4vZRaEOQguVja5NJz7xbXUmoma8a/
eKgt94Bqyfmnv1wIsjgz3AR1mXYMKIZbDxJ1IZvVLwNnp6n6H8Lrh5qrOloICJ0Z
sm0gD85lq/An9FGiYDQkxAlIkYNFHlB0fmQdLw+uKLTRftT7EuGK4RqawrzQW84E
32pZ6fzLTCQ1FQfkpamEOrWaoF4DDvTuBn3YXCtk7bA/8gNCmX7y42PcCR6UHpY=
=7H2V
-----END PGP SIGNATURE-----
Merge tag 'at91-dt' of git://github.com/at91linux/linux-at91 into next/dt
From Nicolas Ferre:
First DT pull-request for 3.14
- many little corrections and documentation updates
- LCD FB Device Tree for at91sam9263 and at91sam9g45 boards
- crypto peripherals DT entries + DMA specification
- new Cosino board
* tag 'at91-dt' of git://github.com/at91linux/linux-at91: (21 commits)
ARM: at91/at91rm9200ek.dts: rearrange nodes in address ascending order
ARM: at91: dt: at91rm9200ek: add emac and nor flash support
ARM: at91: add uart aliases to sama5d3 dtsi
ARM: at91: add i2c2 pinctrl speficifation to sama5d3 DT
ARM: at91: Animeo IP: fix mtd partition table
ARM: at91: at91sam9g45: add i2c pinctrl
ARM: at91: at91sam9g45: set default mmc pinctrl-names
ARM: at91: sama5d3: enable qt1070 as a wakeup source
ARM: at91: add support for Cosino board series by HCE Engineering
ARM: at91/dt/sama5d3: add DMA information to SHA/AES/TDES nodes
ARM: at91/dt/trivial: before sama5d3, Atmel MPU were using at91 prefix
ARM: at91/dt/trivial: use macro for AES irq type
ARM: at91: sam9263ek: add dt lcd support
ARM: at91: at9sam9m10g45ek: add dt lcd support
ARM: at91: sam9263: add fb dt support
ARM: at91: sam9g45: add fb dt support
ARM: at91/dt: binding: add missing compatibility string in SDRAM/DDR documentation
ARM: at91/dt: binding: add precision to AIC documentation
ARM: at91/dt: add atmel,pullup-gpio to at91rm9200ek usb1 definition
ARM: at91/dt: add ethernet phy to at91rm9200ek board
...
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Add .dts and .dtsi file to support sama5d36ek board.
Also update the the comments for sama5d36 in sama5d3.dtsi.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Based on work for the bockw board by Kuninori Morimoto.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Based on work for the r8a7778 SoC by Kuninori Morimoto.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "renesas,intc-irqpin-r8a7779" to the compatible string for the
IRQ pins in case of r8a7779 INTC. This makes the INTC irqpin follow
the same style as the other devices and also makes it more future proof.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "renesas,intc-irqpin-r8a7778" to the compatible string for the
IRQ pins in case of r8a7778 INTC. This makes the INTC irqpin follow
the same style as the other devices and also makes it more future proof.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "renesas,intc-irqpin-r8a7740" to the compatible string for the
IRQ pins in case of r8a7740 INTC. This makes the INTC irqpin follow
the same style as the other devices and also makes it more future proof.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "renesas,intc-irqpin-sh73a0" to the compatible string for the
IRQ pins in case of sh73a0 INTC. This makes the INTC irqpin follow
the same style as the other devices and also makes it more future proof.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch support FSI-WM8978 with simple audio card
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Interrupts generated by SoC internal devices are currently marked as
IRQ_TYPE_NONE. As they're level-triggered and active-high, mark them as
such.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a7791 GPIO resources are currently incorrect. Fix that
by making them match the English r8a7791 v0.31 data sheet.
Tested with GPIO LED using Koelsch DT reference.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms@verge.net.au>
Add 2GiB of DRAM at 0x1_8000_0000 to support the full 4GiB
of Lager system memory in case of DT Reference.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add 2GiB of DRAM at 0x1_8000_0000 to support the full 4GiB
of Lager system memory.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add 1GiB of DRAM at 0x2_0000_0000 to support the full 2GiB
of APE6EVM system memory.
Signed-off-by: Takashi Yoshii <takasi-y@ops.dti.ne.jp>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add 1GiB of DRAM at 0x2_0000_0000 to support the full 2GiB
of APE6EVM system memory also in case of DT reference.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add led6, led7 and led8 to the Koelsch DT reference board support.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use the gpio-keys driver to support the 4 pins on the
dip switch DSW2 which is mounted on the KZM9D board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The device is configured to generate an active-low interrupt signal that
needs to be acknowledged by the host. Configure the IRQ to trigger on
low level.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "renesas,irqc-r8a7790" to the compatible string for IRQC
in case of r8a7790. This makes the IRQC follow the same style
as the other devices and also makes it more future proof.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "renesas,mmcif-r8a7790" to the compatible string for MMCIF
in case of r8a7790. This makes the MMCIF follow the same style
as the other devices and also makes it more future proof.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Hook up the r8a7791 thermal sensor to the DTS.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Hook up the r8a7790 thermal sensor to the DTS.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Configure the "D" set of data signals for SCIF0 and SCIF1
on the Koelsch board to setup pinctrl serial console bits.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "renesas,irqc-r8a7791" to the compatible string for IRQC
in case of r8a7791. This makes the IRQC follow the same style
as the other devices and also makes it more future proof.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
WP pin is not implemented on Marzen
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The device is configured to generate an active-low interrupt signal that
is automatically deasserted without requiring any action from the host.
Configure the IRQ to trigger on falling edge.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The device is configured to generate an active-low interrupt signal that
is automatically deasserted without requiring any action from the host.
Configure the IRQ to trigger on falling edge.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The device is configured to generate an active-low interrupt signal that
is automatically deasserted without requiring any action from the host.
Use falling edge trigger as that is the configuration currently used on
the board.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
In order to allow usage of the preprocessor in the SoC device tree
sources, switch from /include/ to #include.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add minimum clock tree description to .dts file.
This provides same set of clocks as current sh-clkfwk version .c
code does.
Signed-off-by: Takashi Yoshii <takasi-y@ops.dti.ne.jp>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to ePAPR spec,
this patch tidies up DT node name.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to ePAPR spec,
this patch tidies up DT node name.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to ePAPR spec,
this patch tidies up DT node name.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to ePAPR spec,
this patch tidies up DT node name.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to ePAPR spec,
this patch tidies up DT node name.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to ePAPR spec,
this patch tidies up DT node name.
This patch removed un-used "touchscreen" label
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to ePAPR spec,
this patch tidies up DT node name and related clock.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to ePAPR spec,
this patch tidies up DT node name and related clock.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to ePAPR spec,
this patch tidies up DT node name and related clock.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to ePAPR spec,
this patch tidies up DT node name and related clock.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to ePAPR spec,
this patch tidies up DT node name and related clock.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to ePAPR spec,
this patch tidies up DT node name and related clock.
This patch also adds missing SDHI2 entry
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
SCIF0 PFC setting is needed as default
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The PFC device is erroneously declared at address 0xfffc000 instead of
0xfffc0000. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DTS for the DT reference version of the Koelsch board support.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add GPIO controllers to the r8a7791 DTSI file.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
SCIF0/SCIF1 PFC setting is needed as default
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the DT bits for r7s72100 Genmai DT reference support.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add Koelsch and r8a7791 to CONFIG_SHMOBILE_MULTI. At this
point CCF is not yet supported so you cannot run this code
yet. For CCF support to happen several different components
are needed, and this is one simple portion that moves us
forward. Other patches need to build on top of this one.
Koelsch board support exists in 3 flavors:
1) SHMOBILE_MULTI, MACH_KOELSCH - board-koelsch-reference.c (CCF + DT)
2) SHMOBILE, MACH_KOELSCH_REFERENCE - board-koelsch-reference.c (DT)
3) SHMOBILE, MACH_KOELSCH - board-koelsch.c (legacy C code)
When CCF is done then 2) will be removed. When 1) includes same features
as 3) then 3) will be removed.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
SH-Mobile platforms are transitioning from non-multiplatform to
multiplatform kernel. A new ARCH_SHMOBILE_MULTI configuration symbol has
been created to group all multiplatform-enabled SH-Mobile SoCs. The
existing ARCH_SHMOBILE configuration symbol groups SoCs that haven't
been converted yet.
This arrangement works fine for the arch/ code, but lots of drivers
needed on both ARCH_SHMOBILE and ARCH_SHMOBILE_MULTI depend on
ARCH_SHMOBILE only. In order to avoid changing them, rename
ARCH_SHMOBILE to ARCH_SHMOBILE_LEGACY, and create a new boolean
ARCH_SHMOBILE configuration symbol that is selected by both
ARCH_SHMOBILE_LEGACY and ARCH_SHMOBILE_MULTI.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[nicolas.ferre@atmel.com: remove one macb node too many]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Update to production one.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Enable qt1070 keyboard as a wakeup source on sama5d3xek board.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds the Cosino at91sam9g35 based CPU module and the
Cosino Mega 2560 extension board.
Web site: http://www.cosino.it
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
[plagnioj@jcrosoft.com: added "at91-" to files, pinctrl fixed, removed unneeded stuff]
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[nicolas.ferre@atmel.com: adapted to newer kernel, modified commit message]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Change the sha/aes/tdes compatibility string to match common
case for the at91sam9g45 family which is to keep the at91 prefix.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add ethernet phy node in at91rm9200ek.dts.
The reg register is not specified, as it may differ depending on the init
process of the board:
ADDR0/1 phy pins are connected to PA13/14 rm9200 pins. Which means the phy
will take its address from these pins during the reset process.
The macb driver will launch a full scan on the mdio bus to discover the phy
address.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
[nicolas.ferre@atmel.com: changed to IRQ_TYPE_EDGE_BOTH as asked by Boris]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Swap names as they were improperly defined.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Let's add the Ethernet so NFSroot works and the first MMC card
so people can patch in more support easily.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that NAND controller support is available for Armada XP
(cb28e2537a6f: ARM: mvebu: Add support for NAND controller in
Armada 370/XP), this patch enables support for ReadyNAS 2120
and defines default partition layout as delivered by NETGEAR.
As described in similar commits 2be2bc39c6 (ARM: mvebu: Enable
NAND controller in Armada XP GP board) and d8c552dddf (ARM:
mvebu: Enable NAND controller in Armada 370 Mirabox),
"marvell,keep-config" parameter is used as current support does
not allow for setting of timing parameters yet.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that NAND controller support is available for Armada 370
(cb28e2537a6f: ARM: mvebu: Add support for NAND controller in
Armada 370/XP), this patch enables support for ReadyNAS 104 and
defines default partition layout as delivered by NETGEAR.
As described in similar commits 2be2bc39c6 (ARM: mvebu: Enable
NAND controller in Armada XP GP board) and d8c552dddf (ARM:
mvebu: Enable NAND controller in Armada 370 Mirabox),
"marvell,keep-config" parameter is used as current support does
not allow for setting of timing parameters yet.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that NAND controller support is available for Armada 370
(cb28e2537a6f: ARM: mvebu: Add support for NAND controller in
Armada 370/XP), this patch enables support for ReadyNAS 102 and
defines default partition layout as delivered by NETGEAR.
As described in similar commits 2be2bc39c6 (ARM: mvebu: Enable
NAND controller in Armada XP GP board) and d8c552dddf (ARM:
mvebu: Enable NAND controller in Armada 370 Mirabox),
"marvell,keep-config" parameter is used as current support does
not allow for setting of timing parameters yet.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Use GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW instead of 0 and 1.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Replace the numeric key value with a symbolic name from
<bt-bindings/input/input.h>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The am3517 is wrongly booting as omap3 which means that the am3517
specific devices like Ethernet won't work when booted with device
tree. Now with the new devices defined in am3517.dtsi, let's use
that instead of the omap3.dtsi, and add a separate machine entry
for am3517 so am3517-evm can use it.
Signed-off-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: updated comments and fixed build without omap3]
Signed-off-by: Tony Lindgren <tony@atomide.com>
On am3517 there are some extra devices compared to omap3.dtsi that
we currently have not defined. Let's fix that by adding am3517.dtsi
file.
Signed-off-by: Tony Lindgren <tony@atomide.com>
From Srinivas Handagatla, DT updates for STi platforms.
* tag 'DT-for-v3.14-part-1' of http://git.stlinux.com/devel/kernel/linux-sti:
ARM: STi: Add I2C config to B2000 and B2020 boards
ARM: STi: Supply I2C configuration to STiH415 SoC
ARM: STi: Supply I2C configuration to STiH416 SoC
ARM: STi: OF: Fix a typo in pincfg header
Signed-off-by: Olof Johansson <olof@lixom.net>
This is the first step to move AT91 to the CCF.
- core CCF and drivers for most of the clocks
- use of CCF for sama5d3 (100% DT-based)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJSnLhVAAoJEAf03oE53VmQugkH/11ZuSaLsjn31/WvE4WwKdgc
RCIx7r8BCmPLNwDFOgc7tsheH7Jb6I7BNv4MnX8NIPrcAGy6yCEaD8TqhwKGTs9s
2YGoKB48fpwm1udDc6Hfq3/yqkPvM7AnzE1ei1rJNmLt2582tlX1FI+klQG5EoUK
23Pf4yjxtxt31s6xjuvRjEVjEat4PWnuVLs0nZWK6mizApXjA1JPIsKS6NL7q+eG
aBMWDGw0DW4M8VEHAZygxF16PRXnumuB7NAIxKp8SJW5/acSeQntJTNXisMQBem7
DxWfvK7WAFEBGUcRN33a9RpKaHg0Gur1If2sw6CkZ83RnRV9CLqURty1mO4WCUo=
=B+yP
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup' of git://github.com/at91linux/linux-at91 into next/cleanup
From Nicolas Ferre:
AT91: Move to Common Clock Framework and sama5d3 implementation
This is the first step to move AT91 to the CCF.
- core CCF and drivers for most of the clocks
- use of CCF for sama5d3 (100% DT-based)
* tag 'at91-cleanup' of git://github.com/at91linux/linux-at91: (22 commits)
ARM: at91/dt: remove old clk material
ARM: at91: move sama5d3 SoC to common clk
ARM: at91/dt: define sama5d3xek's main clk frequency
ARM: at91/dt: define sama5d3 clocks
ARM: at91: prepare common clk transition for sama5d3 SoC
ARM: at91: prepare sama5 dt boards transition to common clk
ARM: at91: add new compatible strings for pmc driver
ARM: at91: move pit timer to common clk framework
dt: binding: add at91 clks dt bindings documentation
clk: at91: add PMC smd clock
clk: at91: add PMC usb clock
clk: at91: add PMC utmi clock
clk: at91: add PMC programmable clocks
clk: at91: add PMC peripheral clocks
clk: at91: add PMC system clocks
clk: at91: add PMC master clock
clk: at91: add PMC pll clocks
clk: at91: add PMC main clock
clk: at91: add PMC macro file for dt definitions
clk: at91: add PMC base support
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This moves the External Bus Interface (EBI) over to a device
tree node and deletes the static mappings from the platform.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
OMAP5 devices can reach high temperatures and thus
needs to have cpufreq-cooling on systems running on it.
This patch adds the required cooling device properties
so that cpufreq-cpu0 driver loads the cooling device.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-omap@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch changes the dtsi entry on omap5 to contain
the thermal data. This data will enable the passive
cooling with CPUfreq cooling device at 100C. The
system will do a thermal shutdown at 125C whenever
any of its sensors sees this level.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-omap@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch changes a dtsi file to contain the thermal data
for CORE domain on OMAP5 and later SoCs. This data will
enable a thermal shutdown at 125C.
This thermal data can be reused across TI SoC devices.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-omap@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch changes a dtsi file to contain the thermal data
for GPU domain on OMAP5 and later SoCs. This data will
enable a thermal shutdown at 125C.
This thermal data can be reused across TI SoC devices.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-omap@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
OMAP4460 devices can reach high temperatures and thus
needs to have cpufreq-cooling on systems running on it.
This patch adds the required cooling device properties
so that cpufreq-cpu0 driver loads the cooling device.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-omap@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
OMAP4430 devices can reach high temperatures and thus
needs to have cpufreq-cooling on systems running on it.
This patch adds the required cooling device properties
so that cpufreq-cpu0 driver loads the cooling device.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-omap@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch changes the dtsi entry on omap4460 to contain
the thermal data. This data will enable the passive
cooling with CPUfreq cooling device at 100C and the
system will do a thermal shutdown at 125C.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-omap@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch changes the dtsi entry on omap4430 to contain
the thermal data. This data will enable the passive
cooling with CPUfreq cooling device at 100C and the
system will do a thermal shutdown at 125C.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-omap@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch changes a dtsi file to contain the thermal data
for MPU domain on OMAP4 and later SoCs. This data will
enable the passive cooling with CPUfreq cooling device
at 100C and the system will do a thermal shutdown at 125C.
This thermal data can be reused across TI SoC devices.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-omap@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch supplies I2C configuration to B2000 and B2020
based on either STiH415 or STiH416 SoCs.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
This patch fixes a typo for OD define in st-pincfg header file.
Reported-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
- mvebu:
- remove unneeded OS-specific properties from led nodes
- add NAND controller to Armada boards
- add sata leds to readynas 104
- add gpio-poweroff to readynas duo v2
- kirkwood:
- comment cleanup in sheevaplug files
- default pinctrl for sdio
- sdio in guruplug is non-removable
- orion5x:
- typo fix
- dove:
- typo fix
- add PMU interrupt controller and RTC interrupt via same
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=j87K
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-3.14' of git://git.infradead.org/linux-mvebu into next/dt
From Jason Cooper:
mvebu DT changes for v3.14
- mvebu:
- remove unneeded OS-specific properties from led nodes
- add NAND controller to Armada boards
- add sata leds to readynas 104
- add gpio-poweroff to readynas duo v2
- kirkwood:
- comment cleanup in sheevaplug files
- default pinctrl for sdio
- sdio in guruplug is non-removable
- orion5x:
- typo fix
- dove:
- typo fix
- add PMU interrupt controller and RTC interrupt via same
* tag 'mvebu-dt-3.14' of git://git.infradead.org/linux-mvebu:
ARM: Dove: Add RTC interrupt via PMU interrupt controller.
ARM: Dove: Add DT node for PMU interrupt controller.
ARM: mvebu: Add DT entry for ReadyNAS Duo v2 to use gpio-poweroff driver
ARM: mvebu: Add RN104 SATA LEDs driven via NXP PCA9554 I2C to GPIO muxer
ARM: kirkwood: mark guruplug sdio as non-removable
ARM: kirkwood: provide pinctrl default to sdio nodes
ARM: dove: Fix typo in device_type property of phy node
ARM: orion5x: Fix typo in device_type property of phy node
ARM: mvebu: Enable NAND controller in Armada 370 Mirabox
ARM: mvebu: Enable NAND controller in Armada XP GP board
ARM: mvebu: Add support for NAND controller in Armada 370/XP
ARM: kirkwood: Cleanup comments in Sheevaplug dts files
ARM: mvebu: dts: remove unneeded linux,default-state from led nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
- Fix up tc3589x bindings so this chip works again.
- Remove SSP platform devices, as we now boot from device tree
exclusively.
- Delete surplus AB8500/DB8500 platform data, not obtained from
the device tree.
- Add DMA config for the MSP devices.
- A series of 21 patches moving pin control config for the
on-chip Nomadik pin controller from the board file
to the device tree, step by step.
- Two patches to the STE DMA40 driver regarding the high-prio
DMA channel so this can be moved to the device tree. Both have
Vinod's ACK.
- Decommission of the non-device tree boot path for the timer
initialization code.
- Deletion of the non-devicetree probe path from the MTU timer
driver, as all platforms using it are now using device tree.
This has Daniel Lezcano's ACK.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=w9pg
-----END PGP SIGNATURE-----
Merge tag 'ux500-devicetree-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
From Linus Walleij:
Ux500 device tree patches for v3.14, take one:
- Fix up tc3589x bindings so this chip works again.
- Remove SSP platform devices, as we now boot from device tree
exclusively.
- Delete surplus AB8500/DB8500 platform data, not obtained from
the device tree.
- Add DMA config for the MSP devices.
- A series of 21 patches moving pin control config for the
on-chip Nomadik pin controller from the board file
to the device tree, step by step.
- Two patches to the STE DMA40 driver regarding the high-prio
DMA channel so this can be moved to the device tree. Both have
Vinod's ACK.
- Decommission of the non-device tree boot path for the timer
initialization code.
- Deletion of the non-devicetree probe path from the MTU timer
driver, as all platforms using it are now using device tree.
This has Daniel Lezcano's ACK.
* tag 'ux500-devicetree-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (39 commits)
ARM: ux500: decomission custom SMP TWD timer init
clksrc: delete nomadik MTU non-DT boot path
ARM: ux500: decomission the non-DT MTU init sequence
dma: ste_dma40: Parse flags property for new 'high priority channel' request
dma: ste_dma40: Expand DT binding to accept 'high-priority channel' flag
ARM: ux500: Remove checking for DT during timer init
ARM: ux500: Clean-up legacy extern prototype
ARM: ux500: Remove unused call to register AMBA devices
ARM: ux500: Clean-up non-DT IRQ initialisation
pinctrl: nomadik: decomission non-DT boot path
pinctrl: nomadik: move platform data handling into driver
ARM: ux500: get rid of unused header
ARM: ux500: delete Nomadik pinctrl AUXDATA
ARM: ux500: delete remnant pin config macros
ARM: ux500: move snowball pin configs to device tree
ARM: ux500: move snowball LED pin control to device tree
ARM: ux500: convert Snowball SPI pin reference
ARM: ux500: move snowball ethernet config to device tree
ARM: ux500: move HREFv60plus pin configs to device tree
ARM: ux500: move final HREFv60 LCD pins to device tree
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Some of the clocks that were designated gate-clk do not have a gate, so
change those clocks to be of periph-clk type.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
From Tony Lindgren:
Few more legacy booting vs device tree booting fixes that people
have noticed while booting things with device tree for things like
omap4 WLAN, smsc911x, and beagle audio. Hopefully this will be it
for the legacy booting vs device tree fixes for this -rc cycle.
* tag 'omap-for-v3.13/more-dt-regressions' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix the name of supplies for smsc911x shared by OMAP
ARM: OMAP2+: Powerdomain: Fix unchecked dereference of arch_pwrdm
ARM: dts: omap3-beagle: Add omap-twl4030 audio support
ARM: dts: omap4-sdp: Fix pin muxing for wl12xx
ARM: dts: omap4-panda-common: Fix pin muxing for wl12xx
From Nicolas Ferre:
AT91: second round of fixes for 3.13
- reduce IP frequency for I2C on sama5d3
- missing aliases directive for USART3 on 9x5 family
- a PM symbol is missing if !CONFIG_PM
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91: fixed unresolved symbol "at91_pm_set_standby" when built without CONFIG_PM
ARM: at91: add usart3 alias to dtsi
ARM: at91: sama5d3: reduce TWI internal clock frequency
From Jason Cooper, mvebu DT fixes for v3.13:
- mvebu
- PCIe fixes now that we have test devices with more ports.
- fix access to coherency registers
* tag 'mvebu-dt-fixes-3.13' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: re-enable PCIe on Armada 370 DB
ARM: mvebu: use the virtual CPU registers to access coherency registers
ARM: mvebu: fix second and third PCIe unit of Armada XP mv78260
ARM: mvebu: second PCIe unit of Armada XP mv78230 is only x1 capable
From Tony Lindgren:
Some omap related fixes that have come up with people moving to device
tree only based booting for omap2+.
The series contains a handful of fixes for the igep boards as they were
one of the first omap3 boards to jump over completely to device tree
based booting. So these can be considered regressions compared to
booting igep in legacy mode with board files in v3.12.
Also included are few other device tree vs legacy booting regressions:
- yet more missing omap3 .dtsi entries that have showed up booting
various boards with device tree only
- n900 eMMC device tree fix
- fixes for beagle USB EHCI
- two fixes to make omap2420 MMC work
As we're moving omap2+ to be device tree only for v3.14, I'd like to
have v3.13 work equally well for legacy based booting and device tree
based booting. So there will be likely few more device tree related
booting patches trickling in.
This series also includes a regression fix for the omap timer posted
mode that may wrongly stay on from the bootloader for some SoCs.
* tag 'omap-for-v3.13/fixes-against-rc1-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
mmc: omap: Fix I2C dependency and make driver usable with device tree
mmc: omap: Fix DMA configuration to not rely on device id
ARM: dts: omap3-beagle: Fix USB host on beagle boards (for 3.13)
ARM: dts: omap3-igep0020: name twl4030 VPLL2 regulator as vdds_dsi
ARM: dts: AM33XX IGEP0033: add USB support
ARM: dts: AM33XX BASE0033: add 32KBit EEPROM support
ARM: dts: AM33XX BASE0033: add pinmux and user led support
ARM: dts: AM33XX BASE0033: add pinmux and hdmi node to enable display
ARM: dts: omap3-igep0020: Add pinmuxing for DVI output
ARM: dts: omap3-igep0020: Add pinmux setup for i2c devices
ARM: dts: omap3-igep: Update to use the TI AM/DM37x processor
ARM: dts: omap3-igep: Add support for LBEE1USJYC WiFi connected to SDIO
ARM: dts: omap3-igep: Fix bus-width for mmc1
ARM: OMAP2+: dss-common: change IGEP's DVI DDC i2c bus
ARM: OMAP2+: Disable POSTED mode for errata i103 and i767
ARM: OMAP2+: Fix eMMC on n900 with device tree
ARM: OMAP2+: Add fixed regulator to omap2plus_defconfig
ARM: OMAP2+: Fix more missing data for omap3.dtsi file
Signed-off-by: Olof Johansson <olof@lixom.net>
drivers/net/ethernet/smsc/smsc911x.c is expecting supplies named
"vdd33a" and "vddvario". Currently the shared DTS file provides
"vmmc" and "vmmc_aux", and the supply lookup will fail:
smsc911x 2c000000.ethernet: Looking up vdd33a-supply from device tree
smsc911x 2c000000.ethernet: Looking up vdd33a-supply property in node /ocp/gpmc@6e000000/ethernet@gpmc failed
smsc911x 2c000000.ethernet: Looking up vddvario-supply from device tree
smsc911x 2c000000.ethernet: Looking up vddvario-supply property in node /ocp/gpmc@6e000000/ethernet@gpmc failed
Fix it!
Looks like commmit 6b2978ac40 (ARM: dts: Shared file for omap GPMC
connected smsc911x) made the problem more visible by moving the smc911x
configuration from the omap3-igep0020.dts file to the generic file.
But it seems we've had this problem since commit d72b441501
(ARM: dts: omap3-igep0020: Add SMSC911x LAN chip support).
Tested on OMAP3 Overo platform.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
[tony@atomide.com: updated comments for the commits causing the problem]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds typical McBSP2-TWL4030 audio description to the legacy
Beagle Board.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Mux mode for wlan/sdmmc5 should be MODE0 in pinmux_wl12xx_pins and
Enable Pull up on sdmmc5_clk to detect SDIO card.
This fixes WLAN on omap4-sdp that got broken in v3.10 when we
moved omap4 to boot using device tree only as I did not have
the WL12XX card in my omap4 SDP to test with. The commit that
attempted to make WL12XX working on omap4 SDP was 775d2418f3
(ARM: dts: Fix muxing and regulator for wl12xx on the SDIO
bus for blaze).
Signed-off-by: Balaji T K <balajitk@ti.com>
[tony@atomide.com: updated comments for the regression]
Signed-off-by: Tony Lindgren <tony@atomide.com>
pin mux wl12xx_gpio and wl12xx_pins should be part of omap4_pmx_core
and not omap4_pmx_wkup. So, move wl12xx_* to omap4_pmx_core.
Fix the following error message:
pinctrl-single 4a31e040.pinmux: mux offset out of range: 0x38 (0x38)
pinctrl-single 4a31e040.pinmux: could not add functions for pinmux_wl12xx_pins 56x
SDIO card is not detected after moving pin mux to omap4_pmx_core since
sdmmc5_clk pull is disabled. Enable Pull up on sdmmc5_clk to detect SDIO card.
This fixes a regression where WLAN did not work after a warm reset
or after one up/down cycle that happened when we move omap4 to boot
using device tree only. For reference, the kernel bug is described at:
https://bugzilla.kernel.org/show_bug.cgi?id=63821
Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Balaji T K <balajitk@ti.com>
[tony@atomide.com: update comments to describe the regression]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch removes the old main clk node which is now useless as sama5d3
SoCs and boards are no longer compatible with the old at91 clk
implementations.
It also remove old clock definitions (clock definitions using at91 old clk
framework).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Define the main clock frequency for the new main clock node
in sama5d3xcm.dtsi.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Define sama5d3 clocks in sama5d3 device tree.
Add references to the appropriate clocks in each peripheral.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Alias was missing for SoC of the at91sam9x5 familly that embed USART3.
Reported-by: Jiri Prchal <jiri.prchal@aksignal.cz>
[b.brezillon@overkiz.com: advised to place changes in at91sam9x5_usart3.dtsi]
Acked-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Almost all hardware parts of the NETGEAR ReadyNAS NV+ v2 ([1] for more
details) are supported by mainline kernel. The only missing elements in
provided .dts file are:
- the front LCD module (Winstar WINSTAR WH1602): driver development is
ongoing. This is the same LCD module as on ReadyNAS 104.
- the Macronix MX25L512 512Kbit SPI flash: no time to play with it yet.
The device is the big brother (4 vs 2 bay) of the ReadyNAS Duo v2. The
main differences are some additional LEDs for the disks, a Marvell
88SM4140 SATA Port multiplier (no driver required to access the disk)
and previously described LCD module. Otherwise, it shares the same SoC
(kirkwood 88F6282), RAM (256MB), NAND (128MB), RTC chip (Ricoh rs5c372a),
fan controller (GMT G762), XHCI controller (NEC/Renesas µPD720200).
[1]: http://natisbad.org/NAS5/
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
All hardware parts of the (mv78230 Armada XP based) NETGEAR ReadyNAS
2120 are supported by mainline kernel (USB 3.0 and eSATA rear ports,
USB 2.0 front port, Gigabit controller and PHYs for the two rear ports,
serial port, LEDs, Buttons, 88SE9170 SATA controllers, three G762 fan
controllers, G751 temperature sensor) except for:
- the Intersil ISL12057 I2C RTC Chip,
- the Armada NAND controller.
Support for both of those is currently work in progress and does not
prevent boot.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch provides some whitespace cleanup for NETGEAR
ReadyNAS Duo v2 and 102 .dts files:
- Fixed bad spaces
- Added some space between nodes to improve readability
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Exynos5 series SOC's 5250 and 5420 have different versions of
DWMMC controller.So there is a new compatible string to distinguish
between them.So these nodes should be moved out of Exynos5 series
common device tree source to SOC specific device tree source.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The patch does some cleanup work on NETGEAR ReadyNAS 104 .dts
file. Changes are listed below:
- Completed conversion from value to macros for GPIO voltage level
- Converted all numeric input key values to macros
- Fixed all node names and labels to use respectively '-' and '_'
- Made button names more explicit
- Changed order of included files from general to local
- Removed useless clocks and gpio-keys properties
- Document ethernet PHY (Marvell 88E1318) via a comment
- Made G762 clock node name unique by including g762 in it
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The patch does some cleanup work on NETGEAR ReadyNAS 102 .dts
file. Changes are listed below
- Added missing button mpp in pinctrl
- Converted from value to macros for GPIO voltage level
- Converted all numeric input key values to macros
- Added GPIO keys pins to pinctrl
- Made button names more explicit
- Document ethernet PHY (Marvell 88E1318) via a comment
- Made G762 clock node name unique by including g762 in it
- Fixed all node names and labels to use respectively '-' and '_'
- Changed order of included files from general to local
- Removed useless clocks and gpio-keys properties
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The patch does some cleanup work on NETGEAR ReadyNAS Duo v2 .dts
file. Changes are listed below:
- Converted from value to macros for GPIO voltage level
- Converted all numeric input key values to macros
- Made button names more explicit
- Document ethernet PHY (Marvell 88E1318) via a comment
- Added header for the file to describe content and author
- Made G762 clock node name unique by including g762 in it
- Fixed all node names and labels to use respectively '-' and '_'
- Changed order of included files from general to local
- Removed useless clocks and gpio-keys properties
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
We used to set up the GPIO used for the SMC ethernet IRQ by
requesting the GPIO line explicitly. As we recently established
that specifying the GPIO controller as interrupt parent and
requesting one of its interrupts by reference should be enough,
we do away with this. Incidentally, the Nomadik GPIO chip driver
handles this just fine: the IRQ is set up and fired as expected.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The r8a7790 GPIO resources are currently incorrect. Fix that
by making them match the English r8a7790 v0.6 data sheet.
Tested with GPIO LED using Lager DT reference.
This problem has been present since GPIOs were added to the r8a7790 SoC by
f98e10c88a ("ARM: shmobile: r8a7790: Add GPIO controller devices to
device tree") in v3.12-rc1.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Beagle (rev. C4) and Beagle-XM (all revs) need VAUX2 1.8V supply
for the USB PHY.
As the generic PHY driver can't handle more than one supply
at the moment, we configure this supply to be always on.
This will cause a very small power impact if the USB host subsystem
is not in use, about 76.86 micro-W + LDO power.
Older Beagle boards (prior to C4) don't have VAUX2 connected anywhere,
so there won't be any functional impact on those boards other than
some additional LDO power consumption.
Reported-by: Nishanth Menon <nm@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On Device Tree boot the VDDS_DSI regulator is not linked to
the DPI device so omapfb driver probing fails with:
[ 3.186035] OMAPFB: omapfb_probe
[ 3.190704] omapdss DPI error: can't get VDDS_DSI regulator
[ 3.196594] omapfb omapfb: failed to connect default display
[ 3.202667] omapfb omapfb: failed to init overlay connections
[ 3.208892] OMAPFB: free_resources
[ 3.212493] OMAPFB: free all fbmem
[ 3.216735] omapfb omapfb: failed to setup omapfb
As a workaround name the VPLL2 regulator from twl4030 as vdds_dsi
so getting the VDDS_DSI regulator will succeed on dpi_init_regulator().
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add node to support the USB Host and the USB OTG on the IGEP AQUILA
Processor Board.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IGEP AQUILA EXPANSION has a 32KBit EEPROM for user data storage.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the user leds on the IGEP AQUILA EXPANSION. The has two leds,
one green and one red, that are controllable by software.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the hdmi output and the LCD Controller on IGEP AQUILA. Also
configure the correct pinmux for output of video data from the SoC
to the HDMI encoder.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IGEPv2 has a TFP410 DPI-to-DVI encoder attached to OMAP's
Display SubSystem (DSS).
Add mux setup for DSS pins and also for the GPIO 170 pin that
is used to ensure that the DVI-D is powered down on power up.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pin muxing support for IGEP boards i2c controllers.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most of the boards are using the TI AM/DM37x processor, there is only a small
quantity of IGEP Processor Boards based on TI OMAP3530. So it's better use the
omap36xx.dtsi include instead of omap34xx.dtsi include. We can add support
for the 34xx based variant later on as needed.
To avoid confusion we have added to the model the (TI AM/DM37x) comment.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
[tony@atomide.com: updated comments for the 34xx to 36xx include change]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The LBEE1USJYC is a WiFi/BT combo module used on OMAP3-based IGEP boards. In
both cases, IGEPv2 Rev. C and IGEP COM MODULE, the module is connected using
the same MMC interface and uses the same GPIOs.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Both, IGEPv2 and IGEP COM MODULE have a bus-width of 4 not 8, so fix this and
do not mux data pins from mmc1_data4 to mmc1_data7.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the few remaining snowball pin configurations to the device
tree, reference these as hogs to the pin controller until there
are real devices that can make use of them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SPI0 block is not at all connected to the AB8500 on the
Snowball: it is connected to the external header. These pins
on the header may also be used for GPIO, but let's assume
that SPI is a probable usecase on the Snowball and mux in the
SPI block and use these for SPI.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This transfers the muxing and biasing of the ethernet-related
pins on the snowball over to the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the few remaining HREFv60 pin configurations to the device
tree, reference these as hogs to the pin controller until there
are real devices that can make use of them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Put two extra configs into the device tree to handle the default
configuration of the display reset signals on the HREFv60plus,
move this over from the board file to the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the control of muxing and enabling the IPGPIO (image
processor GPIO) from the static set-up to the device tree.
Use a hog as we have no device for the flash controller yet.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves some of the pin setup related to the CW1200 WLAN
module over to the device tree. As the driver is not yet
activated for the CW1200 WLAN we do not assign this pinctrl
state to any device node yet.
Get rid of the cmdline argument passing of a certain U9500
platform variant, as this is not supported by the kernel or
any device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves over the configuration of the GPIO keys (used for
proximity sensor and Hall effect sensor) from the static pin
configuration file to the device tree. As part of the exercise,
implement the GPIO keys properly in a per-UIB file as this
setup actually differs with each UIB.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The old HREFs (MOP500) were controlling an image-processor
GPIO (IPGPIO) by using hogs. Do the same thing with device tree
and get rid of the mop500_pins setting.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the SKE keypad pin control table out of the board
file and into the device tree. This was previously set to be
active on all MOP500 and HREF boards but after reading the
schematic this seems incorrect: the HREFv60 and later uses
one of these for MC5 and no reference designs have the SKE
connected to any hardware so just leave the pins alone
in the power-on state.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the MCDE pin control table out of the board file
and into the device tree. Some pins and configs have been
marked as used by sub-devices or slaves to the MCDE, such
as I2C device 0-070 which is the HDMI interface circuit
AV8100, but the pins rather belong to the MCDE SOC block
as they come out of the main ASIC. The touch screen GPIO
is not related to MCDE so this gets deleted and need to
be tied to the respective touch screen (I2C) device
once that device is added instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we need to connect resources such as pin mappings and clocks
when deleting board files, we create a MCDE node even though there
is no driver for it. As it is only using standard bindings right
now, this does not matter much. When a proper driver is written
for the MCDE, it can augment this node with custom properties.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the SPI pin control table out of the board file
and into the device tree. Move the specific setting for
SSP0 on the HREFprev60 into the prev60-specific DTS file.
The SPI2 configuration is not really connected to any device,
as it will conflict with GPIO218 which is used on all HREFs.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the MUSB pin control table out of the board file
and into the device tree. Tie the config to the on-chip MUSB
device rather than the ab8500-usb device which is off-chip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the input-pulled-up setting for GPIO217 as used
on the HREFs prior to v60 from the boardfile to the device
tree. GPIO218 is only used with the TVK UIB so move it to
that .dtsi file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree. Add nodes for MSP0 and MSP2 on the HREF and Snowball
so we can reference the pins properly.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree. Add entries for SDI1 and SDI2 on the Snowball so that the
WLAN pins on SDI1 can be used further on, and the unused pins
on SDI2 can be put to sleep.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree. Define possible states also for I2C4 even if it's not
used by any board file at this time.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree.
We create a new .dtsi-file to be shared between all the
MOP500-related boards, that include all HREF variants and
the Snowball board. Assign pin states for HREF and Snowball
boards alike.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The TC3589x devices appearing in the ST Ericsson device trees
are adjusted to use the new binding so this is in a good shape,
and we add the keypad on the TVK1281618 UIB so this is working
again.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The RTC on Dove has an interrupt on the PMU interrupt controller.
Add this interrupt to the RTC node. Tested using the
"RTC Driver Test Example"
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Instantiate the PMU interrupt controller which Dove has.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The I2C controller node needs #address-cells and #size-cells properties,
but these are currently missing. Add them. This allows child nodes to be
parsed correctly.
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Basic things like serial, Ethernet, MMC, NAND, DSS, touchscreen
and GPIO keys work.
For twl4030-keypad we're still missing the binding, but
support for that should be trivial to add once the driver
has been updated.
MUSB I'm pretty sure I got got to enumerate once, but I
suspect the battery charging somehow disrupts it and it's
not enumerating in general for some reason.
Patches are welcome to improve things if people are
still using this board.
For reference, here's some more info on this old board:
http://www.openomap.org/wiki/tiki-index.php?page=HardwareInfo
Cc: devicetree@vger.kernel.org
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add minimal device tree support for n8x0 boards so we
can make omap2 device tree only. Note that we still need
to initialize various platform data quirks to keep
things working until n8x0 drivers support device tree.
Here's a rough todo list for the people using n8x0:
1. Update menelaus for device tree and set up
regulators at least for the MMC driver
2. Remove the MMC regulator platform data callback
by using the Menlaus regulators directly in the
driver passed from the .dts file
3. Update GPMC connected devices for onenand and
tusb6010 for device tree
We're planning to remove all legacy platform data
for mach-omap2 over next few merge cycles, so if
people are still using n8x0, please fix the issues
above.
Cc: devicetree@vger.kernel.org
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
I doubt that there are many people using 2430 sdp, but as
that's been historically an important acid test platform
for omap2+ related changes, let's add minimal device
tree support for it.
If anybody is using it beyond minimal boot testing, patches
for more complete device tree support are welcome.
Cc: devicetree@vger.kernel.org
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Without the interrupt you'll get problems if you enable
CONFIG_RTC_DRV_MAX77686. Setup the interrupt properly in the device
tree.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: stable@vger.kernel.org
Looks like we need to configure the regulators and use the pdata
quirk to make eMMC work with device tree.
It seems that mostly vaux3 is used, and only some earlier revisions
used vmmc2. This has been tested to work on devices where the
system_rev passed by the bootloader has versions 0x0010, 0x2101
and 0x2204.
Cc: devicetree@vger.kernel.org
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Sebastian Reichel <sre@debian.org>
[tony@atomide.com: updated with pinctrl changes and comments from Sebastian]
Signed-off-by: Tony Lindgren <tony@atomide.com>
After dropping the duplicate data in hwmod that now should come from
the .dts files, I noticed few more entries missing. Let's add these
as otherwise devices relying on these won't work.
Looks like the side tone entries are bundled into the mcbsp1 to 3,
so that may needs some special handling in the hwmod code as it's
currently trying to look up mcbsp2_sidetone and mcbsp3_sidetone
entries.
Signed-off-by: Tony Lindgren <tony@atomide.com>
From Tony Lindgren:
Few more fixes for issues found booting older omaps using device tree.
Also few randconfig build fixes and removal of some dead code for omap4
as it no longer has legacy platform data based booting support.
* tag 'omap-for-v3.13/more-fixes-for-merge-window-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove legacy omap4_twl6030_hsmmc_init
ARM: OMAP2+: Remove legacy mux code for display.c
ARM: OMAP2+: Fix undefined reference to set_cntfreq
gpio: twl4030: Fix passing of pdata in the device tree case
gpio: twl4030: Fix regression for twl gpio output
ARM: OMAP2+: More randconfig fixes for reconfigure_io_chain
ARM: dts: Fix omap2 specific dtsi files by adding the missing entries
ARM: OMAP2+: Fix GPMC and simplify bootloader timings for 8250 and smc91x
i2c: omap: Fix missing device tree flags for omap2
Commit 14fd8ed0a7 ("ARM: mvebu: Relocate Armada 370/XP PCIe
device tree nodes") relocated the PCIe controller DT nodes one level
up in the Device Tree, to reflect a more correct representation of the
hardware introduced by the mvebu-mbus Device Tree binding.
However, while most of the boards were properly adjusted accordingly,
the Armada 370 DB board was left unchanged, and therefore, PCIe is
seen as not enabled on this board. This patch fixes that by moving the
PCIe controller node one level-up in armada-370-db.dts.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.12+
Fixes: 14fd8ed0a7 "ARM: mvebu: Relocate Armada 370/XP PCIe device tree nodes"
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada XP provides a mechanism called "virtual CPU registers" or
"per-CPU register banking", to access the per-CPU registers of the
current CPU, without having to worry about finding on which CPU we're
running. CPU0 has its registers at 0x21800, CPU1 at 0x21900, CPU2 at
0x21A00 and CPU3 at 0x21B00. The virtual registers accessing the
current CPU registers are at 0x21000.
However, in the Device Tree node that provides the register addresses
for the coherency unit (which is responsible for ensuring coherency
between processors, and I/O coherency between processors and the
DMA-capable devices), a mistake was made: the CPU0-specific registers
were specified instead of the virtual CPU registers. This means that
the coherency barrier needed for I/O coherency was not behaving
properly when executed from a CPU different from CPU0. This patch
fixes that by using the virtual CPU registers.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.8+
Fixes: e60304f8cb "arm: mvebu: Add hardware I/O Coherency support"
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Without that fix, at the end of the shutdown process, the board is
still powered (led glowing, fan running, ...).
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
NETGEAR ReadyNAS 104 has a NXP PCA9554 I2C to GPIO chip. Among the 8 GPIO
lines the chip makes available, four are used on the device to control
the SATA LEDs (the four remaining ones are used for SATA disk presence).
This patch adds DT entries for NXP PCA9554 and the four SATA GPIO LEDs.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Globalscale Guruplug has AW-GH381 WiFi/BT on sdio which is always
present and cannot be detected in any way. Therefore, mark the node
as non-removable instead of broken-cd. While at it, also put a note
about connected WiFi/BT chip above.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
SDIO controllers found on Marvell Kirkwood 6281/6282 SoCs require
pins to be muxed by pinctrl. As there is only one sane pinctrl
setting for this, provide default pinctrl properties to the controller
nodes.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch fixes a typo for device_type property of phy node.
This can work as of today but once a checks are added in generic code
this typo will stop phy from working.
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
This patch fixes a typo for device_type property of phy node.
This can work as of today but once a checks are added in generic code
this typo will stop phy from working.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada 370 Mirabox has a NAND flash, so enable it in the devicetree
and add the partitions as prepared in the factory images.
In order to skip the driver's custom device detection and use only
ONFI detection, the "marvell,keep-config" parameter is used.
This is needed because we have no support for setting the timings parameters yet.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada XP GP board has a NAND flash, so enable it in the devicetree.
In order to skip the driver's custom device detection and use only ONFI
detection, the "marvell,keep-config" parameter is used.
This is needed because we haven't support for setting the timings
parameters yet and must rely in bootloader's.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada 370 and Armada XP SoC have a NAND controller (aka NFCv2).
This commit adds support for it in Armada 370 and Armada XP SoC
common devicetree.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Change the file names given in the comments of the Sheevaplug
dts files to actually match the real file names.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Generally, power LEDs should indicate when power is applied, and go out
once power is removed. _Not_ annoy the developer with migraine-inducing
blinking reminicent of some badly animated television series designed to
sell sugar to children.
On a more serious note, most of these OS-specific properties aren't
necessary and should be removed. I left two that are legitimately tying
disk LEDs to disk activity. Other than that, we keep the state the
bootloader left them in until userspace changes the state via sysfs.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
mv78260 flavour of Marvell Armada XP SoC has 3 PCIe units. The
two first units are both x4 and quad x1 capable. The third unit
is only x4 capable. This patch fixes mv78260 .dtsi to reflect
those capabilities.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.10.x
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Various Marvell datasheets advertise second PCIe unit of mv78230
flavour of Armada XP as x4/quad x1 capable. This second unit is in
fact only x1 capable. This patch fixes current mv78230 .dtsi to
reflect that, i.e. makes 1.0 the second interface (instead of 2.0
at the moment). This was successfully tested on a mv78230-based
ReadyNAS 2120 platform with a x1 device (FL1009 XHCI controller)
connected to this second interface.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.10.x
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The A31 has a reset controller IP that maintains a few other IPs in
reset, among which we can find the UARTs, high speed timers or the I2C.
Now that we have support for them, add the reset controllers to the DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
U-Boot uses the ethernet0 alias to locate the right node to fill in
the MAC address of the first ethernet interface. This patch adds the
alias on all the sunxi SoCs with EMAC. In this way, people using
ethernet in U-Boot (eg, for tftp) can keep a consistent address on both
U-Boot and Linux with no additional effort.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the RTC node to DTS for Allwinner A10 and Allwinner A20.
Signed-off-by: Carlo Caione <carlo.caione@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
- A new driver for TI BQ24735 Battery Chargers, courtesy of NVidia.
- Device tree bindings for TWL4030 chips.
- Random fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=rT+j
-----END PGP SIGNATURE-----
Merge tag 'for-v3.13' of git://git.infradead.org/battery-2.6
Pull battery updates from Anton Vorontsov:
"Highlights:
- A new driver for TI BQ24735 Battery Chargers, courtesy of NVidia.
- Device tree bindings for TWL4030 chips.
- Random fixes and cleanups"
* tag 'for-v3.13' of git://git.infradead.org/battery-2.6:
pm2301-charger: Remove unneeded NULL checks
twl4030_charger: Add devicetree support
power_supply: Fix documentation for TEMP_*ALERT* properties
max17042_battery: Support regmap to access device's registers
max17042_battery: Use SIMPLE_DEV_PM_OPS
charger-manager : Replace kzalloc to devm_kzalloc and remove uneccessary code
bq2415x_charger: Fix max battery regulation voltage
tps65090-charger: Use "IS_ENABLED(CONFIG_OF)" for DT code
tps65090-charger: Drop devm_free_irq of devm_ allocated irq
power_supply: Add support for bq24735 charger
pm2301-charger: Staticize pm2xxx_charger_die_therm_mngt
pm2301-charger: Check return value of regulator_enable
ab8500-charger: Remove redundant break
ab8500-charger: Check return value of regulator_enable
isp1704_charger: Fix driver to work with changes introduced in v3.5
Highlights:
* Support for Calxeda ECX-2000 memory controller, from Robert Richter
* Misc Calxeda Highbank drivers and EDAC core cleanups, from Rob Herring
and Robert Richter
* New maintainer for Freescale's MPC85xx EDAC driver: Johannes Thumshirn
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=pU/h
-----END PGP SIGNATURE-----
Merge tag 'edac_for_3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC updates from Borislav Petkov:
"Following up on last week's discussion, here's my part of the EDAC
pile, highlights in the signed tag.
The last two patches have a date from just now because I've just
applied them to the tree after Johannes sent them to me earlier. I
decided to forward them now because they're trivial.
There's a third one for MPC85xx which adds PCIe error interrupt
support but since it is not so trivial and hasn't seen any linux-next
time, I'm deferring it to 3.14
EDAC update highlights:
- Support for Calxeda ECX-2000 memory controller, from Robert Richter
- Misc Calxeda Highbank drivers and EDAC core cleanups, from Rob
Herring and Robert Richter
- New maintainer for Freescale's MPC85xx EDAC driver: Johannes
Thumshirn"
* tag 'edac_for_3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
edac/85xx: Remove mpc85xx_pci_err_remove
EDAC: Add edac-mpc85xx driver to MAINTAINERS
edac, highbank: Moving error injection to sysfs for edac
edac, highbank: Add MAINTAINERS entry
edac: Unify reporting of device info for device, mc and pci
edac, highbank: Improve and unify naming
edac, highbank: Add Calxeda ECX-2000 support
ARM: dts: calxeda: move memory-controller node out of ecx-common.dtsi
edac, highbank: Fix interrupt setup of mem and l2 controller
The spdif "rxtx5" clock option is being set to ipg clk (62) by mistake.
This causes an incorrect time keeping when spdif driver is running,
because ipg is ancestor clock for clocksource while spdif driver will
change the rate of this clock in certain circumstance. Before the
correct clock for "rxtx5" option can be supplied, let's disable this
option for now by filling a dummy clock for it.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
A first set of batches of fixes for 3.13. The diffstat is large mostly
because we're adding a defconfig for a family that's been lacking it, and
there's some missing clock information added for i.MX and OMAP.
The at91 new code is around dealing with RTC/RTT reset at boot to fix possible
hangs due to pending wakeup interrupts coming in during early boot.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=0oVK
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A first set of batches of fixes for 3.13. The diffstat is large
mostly because we're adding a defconfig for a family that's been
lacking it, and there's some missing clock information added for i.MX
and OMAP.
The at91 new code is around dealing with RTC/RTT reset at boot to fix
possible hangs due to pending wakeup interrupts coming in during early
boot"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
ARM: OMAP2+: Fix build for dra7xx without omap4 and 5
ARM: OMAP2+: omap_device: maintain sane runtime pm status around suspend/resume
doc: devicetree: Add bindings documentation for omap-des driver
ARM: dts: doc: Document missing compatible property for omap-sham driver
ARM: OMAP3: Beagle: fix return value check in beagle_opp_init()
ARM: at91: fix hanged boot due to early rtt-interrupt
ARM: at91: fix hanged boot due to early rtc-interrupt
video: exynos_mipi_dsim: Remove unused variable
ARM: highbank: only select errata 764369 if SMP
ARM: sti: only select errata 764369 if SMP
ARM: tegra: init fuse before setting reset handler
ARM: vt8500: add defconfig for v6/v7 chips
ARM: integrator_cp: Set LCD{0,1} enable lines when turning on CLCD
ARM: OMAP: devicetree: fix SPI node compatible property syntax items
pinctrl: single: call pcs_soc->rearm() whenever IRQ mask is changed
ARM: OMAP2+: smsc911x: fix return value check in gpmc_smsc911x_init()
MAINTAINERS: drop discontinued mailing list
ARM: dts: i.MX51: Fix OTG PHY clock
ARM: imx: set up pllv3 POWER and BYPASS sequentially
ARM: imx: pllv3 needs relock in .set_rate() call
...
Pull input updates from Dmitry Torokhov:
"Updates for the input subsystem. You will get an new drivers for
Hyper-V synthetic keyboard and for Neonode zForce touchscreens, plus a
bunch of driver fixes and cleanups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (49 commits)
Revert "Input: ALPS - add support for model found on Dell XT2"
arm: dts: am335x sk: add touchscreen support
Input: ti_am335x_tsc - fix spelling mistake in TSC/ADC DT binding
Input: cyttsp4 - replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
Input: mma8450 - add missing i2c_set_clientdata() in mma8450_probe()
Input: mpu3050 - add missing i2c_set_clientdata() in mpu3050_probe()
Input: tnetv107x-keypad - make irqs signed for error handling
Input: add driver for Neonode zForce based touchscreens
Input: sh_keysc - enable the driver on all ARM platforms
Input: remove a redundant max() call
Input: mousedev - allow disabling even without CONFIG_EXPERT
Input: allow deselecting serio drivers even without CONFIG_EXPERT
Input: i8042 - add PNP modaliases
Input: evdev - fall back to vmalloc for client event buffer
Input: cypress_ps2 - do not consider data bad if palm is detected
Input: cypress_ps2 - remove useless cast
Input: fix PWM-related undefined reference errors
Input: ALPS - change secondary device's name
Input: wacom - not all multi-interface devices support touch
Input: nspire-keypad - add missing clk_disable_unprepare() on error path
...
with few other fixes that popped up during the merge window.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=4fww
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/fixes-for-merge-window-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Few clock fixes, a runtime PM fix, and pinctrl-single fix along
with few other fixes that popped up during the merge window.
* tag 'omap-for-v3.13/fixes-for-merge-window-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix build for dra7xx without omap4 and 5
ARM: OMAP2+: omap_device: maintain sane runtime pm status around suspend/resume
doc: devicetree: Add bindings documentation for omap-des driver
ARM: dts: doc: Document missing compatible property for omap-sham driver
ARM: OMAP3: Beagle: fix return value check in beagle_opp_init()
ARM: OMAP: devicetree: fix SPI node compatible property syntax items
pinctrl: single: call pcs_soc->rearm() whenever IRQ mask is changed
ARM: OMAP2+: smsc911x: fix return value check in gpmc_smsc911x_init()
+ sync with newer trunk
Looks like we're missing few entries for omap2 and the drivers
have only worked because of the omap hwmod building the devices
for the missing entries.
Let's fix the missing entries so we don't need to rely on hwmod
for the basic data and can then later on remove the duplicate
data from hwmod. Otherwise device tree only drivers will not
work properly.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit f2bf0e72d0 (ARM: OMAP2+: Add minimal 8250 support
for GPMC) added support for using bootloader timings for some
devices. Turns out we can do the same by looking at the compatible
flags of the child without adding a new function as smc91x has
a similar issue as 8250 with the bootloader timings.
And let's fix the 8250 naming, we should use the device type as
the name like uart instead of 8250 for zoom dts file.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull networking updates from David Miller:
1) The addition of nftables. No longer will we need protocol aware
firewall filtering modules, it can all live in userspace.
At the core of nftables is a, for lack of a better term, virtual
machine that executes byte codes to inspect packet or metadata
(arriving interface index, etc.) and make verdict decisions.
Besides support for loading packet contents and comparing them, the
interpreter supports lookups in various datastructures as
fundamental operations. For example sets are supports, and
therefore one could create a set of whitelist IP address entries
which have ACCEPT verdicts attached to them, and use the appropriate
byte codes to do such lookups.
Since the interpreted code is composed in userspace, userspace can
do things like optimize things before giving it to the kernel.
Another major improvement is the capability of atomically updating
portions of the ruleset. In the existing netfilter implementation,
one has to update the entire rule set in order to make a change and
this is very expensive.
Userspace tools exist to create nftables rules using existing
netfilter rule sets, but both kernel implementations will need to
co-exist for quite some time as we transition from the old to the
new stuff.
Kudos to Patrick McHardy, Pablo Neira Ayuso, and others who have
worked so hard on this.
2) Daniel Borkmann and Hannes Frederic Sowa made several improvements
to our pseudo-random number generator, mostly used for things like
UDP port randomization and netfitler, amongst other things.
In particular the taus88 generater is updated to taus113, and test
cases are added.
3) Support 64-bit rates in HTB and TBF schedulers, from Eric Dumazet
and Yang Yingliang.
4) Add support for new 577xx tigon3 chips to tg3 driver, from Nithin
Sujir.
5) Fix two fatal flaws in TCP dynamic right sizing, from Eric Dumazet,
Neal Cardwell, and Yuchung Cheng.
6) Allow IP_TOS and IP_TTL to be specified in sendmsg() ancillary
control message data, much like other socket option attributes.
From Francesco Fusco.
7) Allow applications to specify a cap on the rate computed
automatically by the kernel for pacing flows, via a new
SO_MAX_PACING_RATE socket option. From Eric Dumazet.
8) Make the initial autotuned send buffer sizing in TCP more closely
reflect actual needs, from Eric Dumazet.
9) Currently early socket demux only happens for TCP sockets, but we
can do it for connected UDP sockets too. Implementation from Shawn
Bohrer.
10) Refactor inet socket demux with the goal of improving hash demux
performance for listening sockets. With the main goals being able
to use RCU lookups on even request sockets, and eliminating the
listening lock contention. From Eric Dumazet.
11) The bonding layer has many demuxes in it's fast path, and an RCU
conversion was started back in 3.11, several changes here extend the
RCU usage to even more locations. From Ding Tianhong and Wang
Yufen, based upon suggestions by Nikolay Aleksandrov and Veaceslav
Falico.
12) Allow stackability of segmentation offloads to, in particular, allow
segmentation offloading over tunnels. From Eric Dumazet.
13) Significantly improve the handling of secret keys we input into the
various hash functions in the inet hashtables, TCP fast open, as
well as syncookies. From Hannes Frederic Sowa. The key fundamental
operation is "net_get_random_once()" which uses static keys.
Hannes even extended this to ipv4/ipv6 fragmentation handling and
our generic flow dissector.
14) The generic driver layer takes care now to set the driver data to
NULL on device removal, so it's no longer necessary for drivers to
explicitly set it to NULL any more. Many drivers have been cleaned
up in this way, from Jingoo Han.
15) Add a BPF based packet scheduler classifier, from Daniel Borkmann.
16) Improve CRC32 interfaces and generic SKB checksum iterators so that
SCTP's checksumming can more cleanly be handled. Also from Daniel
Borkmann.
17) Add a new PMTU discovery mode, IP_PMTUDISC_INTERFACE, which forces
using the interface MTU value. This helps avoid PMTU attacks,
particularly on DNS servers. From Hannes Frederic Sowa.
18) Use generic XPS for transmit queue steering rather than internal
(re-)implementation in virtio-net. From Jason Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1622 commits)
random32: add test cases for taus113 implementation
random32: upgrade taus88 generator to taus113 from errata paper
random32: move rnd_state to linux/random.h
random32: add prandom_reseed_late() and call when nonblocking pool becomes initialized
random32: add periodic reseeding
random32: fix off-by-one in seeding requirement
PHY: Add RTL8201CP phy_driver to realtek
xtsonic: add missing platform_set_drvdata() in xtsonic_probe()
macmace: add missing platform_set_drvdata() in mace_probe()
ethernet/arc/arc_emac: add missing platform_set_drvdata() in arc_emac_probe()
ipv6: protect for_each_sk_fl_rcu in mem_check with rcu_read_lock_bh
vlan: Implement vlan_dev_get_egress_qos_mask as an inline.
ixgbe: add warning when max_vfs is out of range.
igb: Update link modes display in ethtool
netfilter: push reasm skb through instead of original frag skbs
ip6_output: fragment outgoing reassembled skb properly
MAINTAINERS: mv643xx_eth: take over maintainership from Lennart
net_sched: tbf: support of 64bit rates
ixgbe: deleting dfwd stations out of order can cause null ptr deref
ixgbe: fix build err, num_rx_queues is only available with CONFIG_RPS
...
This allows the charger to be enabled with devicetree, and allows the
parameters for charging the backup battery to be set.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Kumar Gala <galak@codeaurora.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for deferred
probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSgPQ4AAoJEMhvYp4jgsXif28H/1WkrXq5+lCFQZF8nbYdE2h0
R8PsfiJJmAl6/wFgQTsRel+ScMk2hiP08uTyqf2RLnB1v87gCF7MKVaLOdONfUDi
huXbcQGWCmZv0tbBIklxJe3+X3FIJch4gnyUvPudD1m8a0R0LxWXH/NhdTSFyB20
PNjhN/IzoN40X1PSAhfB5ndWnoxXBoehV/IVHVDU42vkPVbVTyGAw5qJzHW8CLyN
2oGTOalOO4ffQ7dIkBEQfj0mrgGcODToPdDvUQyyGZjYK2FY2sGrjyquir6SDcNa
Q4gwatHTu0ygXpyphjtQf5tc3ZCejJ/F0s3olOAS1ahKGfe01fehtwPRROQnCK8=
=GCbY
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
- Blackfin ADI pin control driver, we move yet another
architecture under this subsystem umbrella.
- Incremental updates to the Renesas Super-H PFC pin control
driver. New subdriver for the r8a7791 SoC.
- Non-linear GPIO ranges from the gpiolib side of things,
this enabled simplified device tree bindings by referring
entire groups of pins on some pin controller to act as
back-end for a certain GPIO-chip driver.
- Add the Abilis TB10x pin control driver used on the ARC
architecture. Also the corresponding GPIO driver is merged
through this tree, so the ARC has full support for pins
and GPIOs after this.
- Subdrivers for Freescale i.MX1, i.MX27 and i.MX50 pin
controller instances. The i.MX1 and i.MX27 is an entirely
new family (silicon) of controllers whereas i.MX50 is
a variant of the previous supported controller.
- Then the usual slew of fixes, cleanups and incremental
updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=z9SM
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Main pin control pull request for the v3.13 cycle.
The changes hitting arch/blackfin are ACKed by the Blackfin
maintainer, and the device tree bindings are ACKed to the extent
possible by someone from the device tree maintainers group.
- Blackfin ADI pin control driver, we move yet another architecture
under this subsystem umbrella.
- Incremental updates to the Renesas Super-H PFC pin control driver.
New subdriver for the r8a7791 SoC.
- Non-linear GPIO ranges from the gpiolib side of things, this
enabled simplified device tree bindings by referring entire groups
of pins on some pin controller to act as back-end for a certain
GPIO-chip driver.
- Add the Abilis TB10x pin control driver used on the ARC
architecture. Also the corresponding GPIO driver is merged through
this tree, so the ARC has full support for pins and GPIOs after
this.
- Subdrivers for Freescale i.MX1, i.MX27 and i.MX50 pin controller
instances. The i.MX1 and i.MX27 is an entirely new family
(silicon) of controllers whereas i.MX50 is a variant of the
previous supported controller.
- Then the usual slew of fixes, cleanups and incremental updates"
The ARC DT changes are apparently still pending, that hopefully gets
sorted out in a timely manner.
* tag 'pinctrl-for-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (48 commits)
pinctrl: imx50: add pinctrl support code for the IMX50 SoC
pinctrl: at91: copy define to driver
pinctrl: remove minor dead code
pinctrl: imx: fix using pin->input_val wrongly
pinctrl: imx1: fix return value check in imx1_pinctrl_core_probe()
gpio: tb10x: fix return value check in tb10x_gpio_probe()
gpio: tb10x: use module_platform_driver to simplify the code
pinctrl: imx27: imx27 pincontrol driver
pinctrl: imx1 core driver
pinctrl: sh-pfc: r8a7791 PFC support
sh-pfc: r8a7778: Add CAN pin groups
gpio: add TB10x GPIO driver
pinctrl: at91: correct a few typos
pinctrl: mvebu: remove redundant of_match_ptr
pinctrl: tb10x: use module_platform_driver to simplify the code
pinctrl: tb10x: fix the error handling in tb10x_pinctrl_probe()
pinctrl: add documentation for pinctrl_get_group_pins()
pinctrl: rockchip: emulate both edge triggered interrupts
pinctrl: rockchip: add rk3188 specifics
pinctrl: rockchip: remove redundant check
...
Pull timer changes from Ingo Molnar:
"Main changes in this cycle were:
- Updated full dynticks support.
- Event stream support for architected (ARM) timers.
- ARM clocksource driver updates.
- Move arm64 to using the generic sched_clock framework & resulting
cleanup in the generic sched_clock code.
- Misc fixes and cleanups"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (50 commits)
x86/time: Honor ACPI FADT flag indicating absence of a CMOS RTC
clocksource: sun4i: remove IRQF_DISABLED
clocksource: sun4i: Report the minimum tick that we can program
clocksource: sun4i: Select CLKSRC_MMIO
clocksource: Provide timekeeping for efm32 SoCs
clocksource: em_sti: convert to clk_prepare/unprepare
time: Fix signedness bug in sysfs_get_uname() and its callers
timekeeping: Fix some trivial typos in comments
alarmtimer: return EINVAL instead of ENOTSUPP if rtcdev doesn't exist
clocksource: arch_timer: Do not register arch_sys_counter twice
timer stats: Add a 'Collection: active/inactive' line to timer usage statistics
sched_clock: Remove sched_clock_func() hook
arch_timer: Move to generic sched_clock framework
clocksource: tcb_clksrc: Remove IRQF_DISABLED
clocksource: tcb_clksrc: Improve driver robustness
clocksource: tcb_clksrc: Replace clk_enable/disable with clk_prepare_enable/disable_unprepare
clocksource: arm_arch_timer: Use clocksource for suspend timekeeping
clocksource: dw_apb_timer_of: Mark a few more functions as __init
clocksource: Put nodes passed to CLOCKSOURCE_OF_DECLARE callbacks centrally
arm: zynq: Enable arm_global_timer
...
Proper clock ID for USB OTG PHY is "usb_phy_gate".
The patch changes this mismatch.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Most of this branch consists of updates, additions and general churn of
the device tree source files in the kernel (arch/arm/boot/dts). Besides
that, there are a few things to point out:
- Lots of platform conversion on OMAP2+, with removal of old board files
for various platforms.
- Final conversion of a bunch of ux500 (ST-Ericsson) platforms as well
- Some updates to pinctrl and other subsystems. Most of these are for
DT-enablement of the various platforms and acks have been collected.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=nH67
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"Most of this branch consists of updates, additions and general churn
of the device tree source files in the kernel (arch/arm/boot/dts).
Besides that, there are a few things to point out:
- Lots of platform conversion on OMAP2+, with removal of old board
files for various platforms.
- Final conversion of a bunch of ux500 (ST-Ericsson) platforms as
well
- Some updates to pinctrl and other subsystems. Most of these are
for DT-enablement of the various platforms and acks have been
collected"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (385 commits)
ARM: dts: bcm11351: Use GIC/IRQ defines for sdio interrupts
ARM: dts: bcm: Add missing UARTs for bcm11351 (bcm281xx)
ARM: dts: bcm281xx: Add card detect GPIO
ARM: dts: rename ARCH_BCM to ARCH_BCM_MOBILE (dt)
ARM: bcm281xx: Add device node for the GPIO controller
ARM: mvebu: Add Netgear ReadyNAS 104 board
ARM: tegra: fix Tegra114 IOMMU register address
ARM: kirkwood: add support for OpenBlocks A7 platform
ARM: dts: omap4-panda: add DPI pinmuxing
ARM: dts: AM33xx: Add RNG node
ARM: dts: AM33XX: Add hwspinlock node
ARM: dts: OMAP5: Add hwspinlock node
ARM: dts: OMAP4: Add hwspinlock node
ARM: dts: use 'status' property for PCIe nodes
ARM: dts: sirf: add missed address-cells and size-cells for prima2 I2C
ARM: dts: sirf: add missed cell, cs and dma channel for SPI nodes
ARM: dts: sirf: add missed graphics2d iobg in atlas6 dts
ARM: dts: sirf: add missed chhifbg node in prima2 and atlas6 dts
ARM: dts: sirf: add missed memcontrol-monitor node in prima2 and atlas6 dts
ARM: mvebu: Add the core-divider clock to Armada 370/XP
...
Add missing nodes for the touchscreen available on AM335x EVM SK.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There was a spelling mistake on TSC/ADC binding where "coordinate" was
spelled as "coordiante".
We can't simply fix the error due to DT being an ABI, the approach taken
was to first use correct spelling and if that fails, fall back to
miss-spelled version.
It's unfortunate that has creeped into the tree.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Board-related updates. This branch is getting smaller and smaller, which is
the whole idea so that's reassuring.
Right now by far most of the code is related to shmobile updates, and
they are now switching over to removal of board code and migration to
multiplatform, so we'll see their board code base shrink in the near
future too, I hope.
In addition to that is some defconfig updates, some display updates for OMAP
and a bit of new board support for Rockchip boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ZYOa
-----END PGP SIGNATURE-----
Merge tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board updates from Olof Johansson:
"Board-related updates. This branch is getting smaller and smaller,
which is the whole idea so that's reassuring.
Right now by far most of the code is related to shmobile updates, and
they are now switching over to removal of board code and migration to
multiplatform, so we'll see their board code base shrink in the near
future too, I hope.
In addition to that is some defconfig updates, some display updates
for OMAP and a bit of new board support for Rockchip boards"
* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (56 commits)
ARM: rockchip: add support for rk3188 and Radxa Rock board
ARM: rockchip: add dts for bqcurie2 tablet
ARM: rockchip: enable arm-global-timer
ARM: rockchip: move shared dt properties to common source file
ARM: OMAP2+: display: Create omap_vout device inside omap_display_init
ARM: OMAP2+: display: Create omapvrfb and omapfb devices inside omap_display_init
ARM: OMAP2+: display: Create omapdrm device inside omap_display_init
ARM: OMAP2+: drm: Don't build device for DMM
ARM: tegra: defconfig updates
RX-51: Add support for OMAP3 ROM Random Number Generator
ARM: OMAP3: RX-51: ARM errata 430973 workaround
ARM: OMAP3: Add secure function omap_smc3() which calling instruction smc #1
ARM: shmobile: marzen: enable INTC IRQ
ARM: shmobile: bockw: add SMSC support on reference
ARM: shmobile: Use SMP on Koelsch
ARM: shmobile: Remove KZM9D reference DTS
ARM: shmobile: Let KZM9D multiplatform boot with KZM9D DTB
ARM: shmobile: Remove non-multiplatform KZM9D reference support
ARM: shmobile: Use KZM9D without reference for multiplatform
ARM: shmobile: Sync KZM9D DTS with KZM9D reference DTS
...
New and updated SoC support. Among the things new for this release are:
- More support for the AM33xx platforms from TI
- Tegra 124 support, and some updates to older tegra families as well
- imx cleanups and updates across the board
- A rename of Broadcom's Mobile platforms which were introduced as ARCH_BCM,
and turned out to be too broad a name. New name is ARCH_BCM_MOBILE.
- A whole bunch of updates and fixes for integrator, making the platform code
more modern and switches over to DT-only booting.
- Support for two new Renesas shmobile chipsets. Next up for them is more work
on consolidation instead of introduction of new non-multiplatform SoCs, we're
all looking forward to that!
- Misc cleanups for older Samsung platforms, some Allwinner updates, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WYJl
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"New and updated SoC support. Among the things new for this release
are:
- More support for the AM33xx platforms from TI
- Tegra 124 support, and some updates to older tegra families as well
- imx cleanups and updates across the board
- A rename of Broadcom's Mobile platforms which were introduced as
ARCH_BCM, and turned out to be too broad a name. New name is
ARCH_BCM_MOBILE.
- A whole bunch of updates and fixes for integrator, making the
platform code more modern and switches over to DT-only booting.
- Support for two new Renesas shmobile chipsets. Next up for them is
more work on consolidation instead of introduction of new
non-multiplatform SoCs, we're all looking forward to that!
- Misc cleanups for older Samsung platforms, some Allwinner updates,
etc"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (159 commits)
ARM: bcm281xx: Add ARCH_BCM_MOBILE to bcm config
ARM: bcm_defconfig: Run "make savedefconfig"
ARM: bcm281xx: Add ARCH Timers to config
rename ARCH_BCM to ARCH_BCM_MOBILE (mach-bcm)
ARM: vexpress: Enable platform-specific options in defconfig
ARM: vexpress: Make defconfig work again
ARM: sunxi: remove .init_time hooks
ARM: imx: enable suspend for imx6sl
ARM: imx: ensure dsm_request signal is not asserted when setting LPM
ARM: imx6q: call WB and RBC configuration from imx6q_pm_enter()
ARM: imx6q: move low-power code out of clock driver
ARM: imx: drop extern with function prototypes in common.h
ARM: imx: reset core along with enable/disable operation
ARM: imx: do not return from imx_cpu_die() call
ARM: imx_v6_v7_defconfig: Select CONFIG_PROVE_LOCKING
ARM: imx_v6_v7_defconfig: Enable LEDS_GPIO related options
ARM: mxs_defconfig: Turn off CONFIG_DEBUG_GPIO
ARM: imx: replace imx6q_restart() with mxc_restart()
ARM: mach-imx: mm-imx5: Retrieve iomuxc base address from dt
ARM: mach-imx: mm-imx5: Retrieve tzic base address from dt
...
This branch contains code cleanups, moves and removals for 3.13.
Qualcomm msm targets had a bunch of code removal for legacy non-DT
platforms. Nomadik saw more device tree conversions and cleanup of old
code. Tegra has some code refactoring, etc.
One longish patch series from Sebastian Hasselbarth changes the init_time
hooks and tries to use a generic implementation for most platforms,
since they were all doing more or less the same things.
Finally the "shark" platform is removed in this release. It's been
abandoned for a while and nobody seems to care enough to keep it
around. If someone comes along and wants to resurrect it, the removal
can easily be reverted and code brought back.
Beyond this, mostly a bunch of removals of stale content across the
board, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=SHZQ
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This branch contains code cleanups, moves and removals for 3.13.
Qualcomm msm targets had a bunch of code removal for legacy non-DT
platforms. Nomadik saw more device tree conversions and cleanup of
old code. Tegra has some code refactoring, etc.
One longish patch series from Sebastian Hasselbarth changes the
init_time hooks and tries to use a generic implementation for most
platforms, since they were all doing more or less the same things.
Finally the "shark" platform is removed in this release. It's been
abandoned for a while and nobody seems to care enough to keep it
around. If someone comes along and wants to resurrect it, the removal
can easily be reverted and code brought back.
Beyond this, mostly a bunch of removals of stale content across the
board, etc"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (79 commits)
ARM: gemini: convert to GENERIC_CLOCKEVENTS
ARM: EXYNOS: remove CONFIG_MACH_EXYNOS[4, 5]_DT config options
ARM: OMAP3: control: add API for setting IVA bootmode
ARM: OMAP3: CM/control: move CM scratchpad save to CM driver
ARM: OMAP3: McBSP: do not access CM register directly
ARM: OMAP3: clock: add API to enable/disable autoidle for a single clock
ARM: OMAP2: CM/PM: remove direct register accesses outside CM code
MAINTAINERS: Add patterns for DTS files for AT91
ARM: at91: remove init_machine() as default is suitable
ARM: at91/dt: split sama5d3 peripheral definitions
ARM: at91/dt: split sam9x5 peripheral definitions
ARM: Remove temporary sched_clock.h header
ARM: clps711x: Use linux/sched_clock.h
MAINTAINERS: Add DTS files to patterns for Samsung platform
ARM: EXYNOS: remove unnecessary header inclusions from exynos4/5 dt machine file
ARM: tegra: fix ARCH_TEGRA_114_SOC select sort order
clk: nomadik: fix missing __init on nomadik_src_init
ARM: drop explicit selection of HAVE_CLK and CLKDEV_LOOKUP
ARM: S3C64XX: Kill CONFIG_PLAT_S3C64XX
ASoC: samsung: Use CONFIG_ARCH_S3C64XX to check for S3C64XX support
...
A set of fixes for various platforms that weren't considered bad enough
to include in 3.12 (nor -stable). Mostly simple typo fixes, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=70+h
-----END PGP SIGNATURE-----
Merge tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC low-priority fixes from Olof Johansson:
"A set of fixes for various platforms that weren't considered bad
enough to include in 3.12 (nor -stable). Mostly simple typo fixes,
etc"
* tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP2+: irq, AM33XX add missing register check
ARM: OMAP2+: wakeupgen: AM43x adaptation
ARM: OMAP1: Fix a bunch of GPIO related section warnings after initdata got corrected
ARM: dts: fix PL330 MDMA1 address in DT for Universal C210 board
ARM: dts: Work around lack of cpufreq regulator lookup for exynos4210-origen and trats boards
ARM: dts: Fix typo earlyprintk in exynos5440-sd5v1 and ssdk5440 boards
ARM: dts: Correct typo in use of samsung,pin-drv for exynos5250
ARM: rockchip: remove obsolete rockchip,config properties
ARM: rockchip: fix wrong use of non-existent CONFIG_LOCAL_TIMERS
ARM: mach-omap1: Fix omap1510_fpga_init_irq() implicit declarations.
ARM: OMAP1: fix incorrect placement of __initdata tag
ARM: OMAP: remove deprecated IRQF_DISABLED
ARM: OMAP2+: throw the die id into the entropy pool
Here's the big drivers/staging/ update for 3.13-rc1.
Nothing major here, just a _ton_ of fixes and cleanups, mostly driven by
the new round of OPW applicants, but also there are lots of other people
doing staging tree cleanups these days in order to help get the drivers
into mergable shape.
We also merge, and then revert, the ktap code, as Ingo and the other
perf/ftrace developers feel it should go into the "real" part of the
kernel with only a bit more work, so no need to put it in staging for
now.
All of this has been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlJ6xPsACgkQMUfUDdst+ykAbwCg1hOktgHPFZp/t6xmsSj6cZHj
AfQAnRN/lr/TFw5SKUek2sluAzO4Fz7c
=g/MD
-----END PGP SIGNATURE-----
Merge tag 'staging-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver update from Greg KH:
"Here's the big drivers/staging/ update for 3.13-rc1.
Nothing major here, just a _ton_ of fixes and cleanups, mostly driven
by the new round of OPW applicants, but also there are lots of other
people doing staging tree cleanups these days in order to help get the
drivers into mergable shape.
We also merge, and then revert, the ktap code, as Ingo and the other
perf/ftrace developers feel it should go into the "real" part of the
kernel with only a bit more work, so no need to put it in staging for
now.
All of this has been in linux-next for a while with no reported
issues"
* tag 'staging-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1045 commits)
staging: drm/imx: fix return value check in ipu_add_subdevice_pdata()
Staging: zram: Fix access of NULL pointer
Staging: zram: Fix variable dereferenced before check
Staging: rtl8187se: space prohibited before semicolon in r8185b_init.c
Staging: rtl8187se: fix space prohibited after that open parenthesis '(' in r8185b_init.c
Staging: rtl8187se: fix braces {} are not necessary for single statement blocks in r8185b_init.c
Staging: rtl8187se: fix trailing whitespace in r8185b_init.c
Staging: rtl8187se: fix please, no space before tabs in r8185b_init.c
drivers/staging/nvec/Kconfig: remove trailing whitespace
Staging: dwc2: Fix variable dereferenced before check
Staging: xgifb: fix braces {} are not necessary for any arm of this statement
staging: rtl8192e: remove unneeded semicolons
staging: rtl8192e: use true and false for bool variables
staging: ft1000: return values corrected in scram_start_dwnld
staging: ft1000: change values of status return variable in write_dpram32_and_check
staging: bcm: Remove unnecessary pointer casting
imx-drm: ipuv3-crtc: Invert IPU DI0 clock polarity
staging: r8188eu: Fix sparse warnings in rtl_p2p.c
staging: r8188eu: Fix sparse warnings in rtw_mlme_ext.c
staging: r8188eu: Fix sparse warnings in rtl8188e.cmd.c
...
Here's the big USB driver update for 3.13-rc1.
It includes the usual xhci changes, EHCI updates to get the scheduling
of USB transactions working better, and a raft of gadget and musb
updates as well.
All of this has been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlJ6xycACgkQMUfUDdst+ymO+gCgxXdQXSU23i9ykc2CKBemdEBH
w6IAoKcokITcdN1IxxkfiMxOEld2hgZm
=3kbb
-----END PGP SIGNATURE-----
Merge tag 'usb-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB driver update from Greg KH:
"Here's the big USB driver update for 3.13-rc1.
It includes the usual xhci changes, EHCI updates to get the scheduling
of USB transactions working better, and a raft of gadget and musb
updates as well.
All of this has been in linux-next for a while with no reported
issues"
* tag 'usb-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (305 commits)
USB: Maintainers change for usb serial drivers
usb: usbtest: support container id descriptor test
usb: usbtest: support superspeed device capbility descriptor test
usb: usbtest: support usb2 extension descriptor test
usb: chipidea: only get vbus regulator for non-peripheral mode
USB: ehci-atmel: add usb_clk for transition to CCF
usb: cdc-wdm: ignore speed change notifications
USB: cdc-wdm: support back-to-back USB_CDC_NOTIFY_RESPONSE_AVAILABLE notifications
usbatm: Fix dynamic_debug / ratelimited atm_dbg and atm_rldbg macros
printk: pr_debug_ratelimited: check state first to reduce "callbacks suppressed" messages
usb: usbtest: support bos descriptor test for usb 3.0
USB: phy: samsung: Support multiple PHYs of same type
usb: wusbcore: change WA_SEGS_MAX to a legal value
usb: wusbcore: add a quirk for Alereon HWA device isoc behavior
usb: wusbcore: combine multiple isoc frames in a single transfer request.
usb: wusbcore: set the RPIPE wMaxPacketSize value correctly
usb: chipidea: host: more enhancement when ci->hcd is NULL
usb: ohci: remove ep93xx bus glue platform driver
usb: usbtest: fix checkpatch warning as sizeof code style
UWB: clean up attribute use by using ATTRIBUTE_GROUPS()
...
Stephen Warren