Add a flag to DMA memory allocation to silence a warning.
This driver allocates DMA memory for IO frames. This allocation may exceed
MAX_ORDER pages for few megaraid_sas controllers (controllers with very
high queue depth). Consequently, the driver has logic to keep reducing the
controller queue depth until the DMA memory allocation succeeds.
On impacted megaraid_sas controllers there would be multiple DMA allocation
failures until driver settled on an allocation that fit. These failed DMA
allocation requests caused stack traces in system logs. These were not
harmful and this patch silences those warnings/stack traces.
[mkp: clarified commit desc]
Link: https://lore.kernel.org/r/20200204152413.7107-1-thenzl@redhat.com
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
IOCTLs causing firmware fault may end up in failed controller resets and
finally killing the adapter.
This patch fixes this problem as stated below:
In OCR sequence, driver will attempt refiring pended IOCTLs upto two times.
If first two attempts fail, then in third attempt driver will return pended
IOCTLs with EBUSY status to application. These changes are done to ensure
if any of pended IOCTLs is causing firmware fault and resulting into OCR
failure, then in last attempt of OCR driver will refrain firing it to
firmware and saving adapter from being killed due to faulty IOCTL.
Link: https://lore.kernel.org/r/1579000882-20246-10-git-send-email-anand.lodnoor@broadcom.com
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Anand Lodnoor <anand.lodnoor@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver initiates OCR if a DCMD command times out. But there is a deadlock
if the driver attempts to invoke another OCR before the mutex lock
(reset_mutex) is released from the previous session of OCR.
This patch takes care of the above scenario using new flag
MEGASAS_FUSION_OCR_NOT_POSSIBLE to indicate if OCR is possible.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1579000882-20246-9-git-send-email-anand.lodnoor@broadcom.com
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Anand Lodnoor <anand.lodnoor@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After issuing a adapter reset, driver blindly used to set adprecovery flag
to OPERATIONAL state. Add a check to see if the FW is operational before
setting the flag and marking reset adapter successful.
Link: https://lore.kernel.org/r/1579000882-20246-7-git-send-email-anand.lodnoor@broadcom.com
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Anand Lodnoor <anand.lodnoor@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
At the time of firmware initialization, if JBOD map or RAID map is not
available, driver can function without these features in a limited
functionality mode.
Link: https://lore.kernel.org/r/1579000882-20246-6-git-send-email-anand.lodnoor@broadcom.com
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Anand Lodnoor <anand.lodnoor@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly update of the usual drivers: qla2xxx, ufs, smartpqi,
lpfc, hisi_sas, qedf, mpt3sas; plus a whole load of minor updates.
The only core change this time around is the addition of request
batching for virtio. Since batching requires an additional flag to
use, it should be invisible to the rest of the drivers.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXYQE/yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishXs9AP4usPY5
OpMlF6OiKFNeJrCdhCScVghf9uHbc7UA6cP+EgD/bCtRgcDe1ZjOTYWdeTwvwWqA
ltWYonnv6Lg3b1f9yqI=
=jRC/
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: qla2xxx, ufs, smartpqi,
lpfc, hisi_sas, qedf, mpt3sas; plus a whole load of minor updates. The
only core change this time around is the addition of request batching
for virtio. Since batching requires an additional flag to use, it
should be invisible to the rest of the drivers"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (264 commits)
scsi: hisi_sas: Fix the conflict between device gone and host reset
scsi: hisi_sas: Add BIST support for phy loopback
scsi: hisi_sas: Add hisi_sas_debugfs_alloc() to centralise allocation
scsi: hisi_sas: Remove some unused function arguments
scsi: hisi_sas: Remove redundant work declaration
scsi: hisi_sas: Remove hisi_sas_hw.slot_complete
scsi: hisi_sas: Assign NCQ tag for all NCQ commands
scsi: hisi_sas: Update all the registers after suspend and resume
scsi: hisi_sas: Retry 3 times TMF IO for SAS disks when init device
scsi: hisi_sas: Remove sleep after issue phy reset if sas_smp_phy_control() fails
scsi: hisi_sas: Directly return when running I_T_nexus reset if phy disabled
scsi: hisi_sas: Use true/false as input parameter of sas_phy_reset()
scsi: hisi_sas: add debugfs auto-trigger for internal abort time out
scsi: virtio_scsi: unplug LUNs when events missed
scsi: scsi_dh_rdac: zero cdb in send_mode_select()
scsi: fcoe: fix null-ptr-deref Read in fc_release_transport
scsi: ufs-hisi: use devm_platform_ioremap_resource() to simplify code
scsi: ufshcd: use devm_platform_ioremap_resource() to simplify code
scsi: hisi_sas: use devm_platform_ioremap_resource() to simplify code
scsi: ufs: Use kmemdup in ufshcd_read_string_desc()
...
The commit de516379e8 ("scsi: megaraid_sas: changes to function
prototypes") introduced a comilation warning due to it changed the function
prototype of read_fw_status_reg() to take an instance pointer instead, but
forgot to remove an unused variable.
drivers/scsi/megaraid/megaraid_sas_fusion.c: In function
'megasas_fusion_update_can_queue':
drivers/scsi/megaraid/megaraid_sas_fusion.c:326:39: warning: variable
'reg_set' set but not used [-Wunused-but-set-variable]
struct megasas_register_set __iomem *reg_set;
^~~~~~~
Fixes: de516379e8 ("scsi: megaraid_sas: changes to function prototypes")
Signed-off-by: Qian Cai <cai@lca.pw>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix sparse warnings:
drivers/scsi/megaraid/megaraid_sas_fusion.c:3369:1: warning: symbol 'complete_cmd_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:3535:6: warning: symbol 'megasas_sync_irqs' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:3554:1: warning: symbol 'megasas_complete_cmd_dpc_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:3573:13: warning: symbol 'megasas_isr_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:3604:1: warning: symbol 'build_mpt_mfi_pass_thru' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:3661:40: warning: symbol 'build_mpt_cmd' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:3688:1: warning: symbol 'megasas_issue_dcmd_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:3881:5: warning: symbol 'megasas_wait_for_outstanding_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:4005:6: warning: symbol 'megasas_refire_mgmt_cmd' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:4525:25: warning: symbol 'megasas_get_peer_instance' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:4825:7: warning: symbol 'megasas_fusion_crash_dump' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix sparse warnings:
drivers/scsi/megaraid/megaraid_sas_fusion.c:541:1: warning: symbol 'megasas_alloc_cmdlist_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:580:1: warning: symbol 'megasas_alloc_request_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:661:1: warning: symbol 'megasas_alloc_reply_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:738:1: warning: symbol 'megasas_alloc_rdpq_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:920:1: warning: symbol 'megasas_alloc_cmds_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:1740:1: warning: symbol 'megasas_init_adapter_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:1966:1: warning: symbol 'map_cmd_status' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:2379:1: warning: symbol 'megasas_set_pd_lba' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:2718:1: warning: symbol 'megasas_build_ldio_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:3215:1: warning: symbol 'megasas_build_io_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:3328:6: warning: symbol 'megasas_prepare_secondRaid1_IO' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly update of the usual drivers: qla2xxx, hpsa, lpfc, ufs,
mpt3sas, ibmvscsi, megaraid_sas, bnx2fc and hisi_sas as well as the
removal of the osst driver (I heard from Willem privately that he
would like the driver removed because all his test hardware has
failed). Plus number of minor changes, spelling fixes and other
trivia.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXSTl4yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdcxAQDCJVbd
fPUX76/V1ldupunF97+3DTharxxbst+VnkOnCwD8D4c0KFFFOI9+F36cnMGCPegE
fjy17dQLvsJ4GsidHy8=
=aS5B
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: qla2xxx, hpsa, lpfc, ufs,
mpt3sas, ibmvscsi, megaraid_sas, bnx2fc and hisi_sas as well as the
removal of the osst driver (I heard from Willem privately that he
would like the driver removed because all his test hardware has
failed). Plus number of minor changes, spelling fixes and other
trivia.
The big merge conflict this time around is the SPDX licence tags.
Following discussion on linux-next, we believe our version to be more
accurate than the one in the tree, so the resolution is to take our
version for all the SPDX conflicts"
Note on the SPDX license tag conversion conflicts: the SCSI tree had
done its own SPDX conversion, which in some cases conflicted with the
treewide ones done by Thomas & co.
In almost all cases, the conflicts were purely syntactic: the SCSI tree
used the old-style SPDX tags ("GPL-2.0" and "GPL-2.0+") while the
treewide conversion had used the new-style ones ("GPL-2.0-only" and
"GPL-2.0-or-later").
In these cases I picked the new-style one.
In a few cases, the SPDX conversion was actually different, though. As
explained by James above, and in more detail in a pre-pull-request
thread:
"The other problem is actually substantive: In the libsas code Luben
Tuikov originally specified gpl 2.0 only by dint of stating:
* This file is licensed under GPLv2.
In all the libsas files, but then muddied the water by quoting GPLv2
verbatim (which includes the or later than language). So for these
files Christoph did the conversion to v2 only SPDX tags and Thomas
converted to v2 or later tags"
So in those cases, where the spdx tag substantially mattered, I took the
SCSI tree conversion of it, but then also took the opportunity to turn
the old-style "GPL-2.0" into a new-style "GPL-2.0-only" tag.
Similarly, when there were whitespace differences or other differences
to the comments around the copyright notices, I took the version from
the SCSI tree as being the more specific conversion.
Finally, in the spdx conversions that had no conflicts (because the
treewide ones hadn't been done for those files), I just took the SCSI
tree version as-is, even if it was old-style. The old-style conversions
are perfectly valid, even if the "-only" and "-or-later" versions are
perhaps more descriptive.
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (185 commits)
scsi: qla2xxx: move IO flush to the front of NVME rport unregistration
scsi: qla2xxx: Fix NVME cmd and LS cmd timeout race condition
scsi: qla2xxx: on session delete, return nvme cmd
scsi: qla2xxx: Fix kernel crash after disconnecting NVMe devices
scsi: megaraid_sas: Update driver version to 07.710.06.00-rc1
scsi: megaraid_sas: Introduce various Aero performance modes
scsi: megaraid_sas: Use high IOPS queues based on IO workload
scsi: megaraid_sas: Set affinity for high IOPS reply queues
scsi: megaraid_sas: Enable coalescing for high IOPS queues
scsi: megaraid_sas: Add support for High IOPS queues
scsi: megaraid_sas: Add support for MPI toolbox commands
scsi: megaraid_sas: Offload Aero RAID5/6 division calculations to driver
scsi: megaraid_sas: RAID1 PCI bandwidth limit algorithm is applicable for only Ventura
scsi: megaraid_sas: megaraid_sas: Add check for count returned by HOST_DEVICE_LIST DCMD
scsi: megaraid_sas: Handle sequence JBOD map failure at driver level
scsi: megaraid_sas: Don't send FPIO to RL Bypass queue
scsi: megaraid_sas: In probe context, retry IOC INIT once if firmware is in fault
scsi: megaraid_sas: Release Mutex lock before OCR in case of DCMD timeout
scsi: megaraid_sas: Call disable_irq from process IRQ poll
scsi: megaraid_sas: Remove few debug counters from IO path
...
For Aero adapters, driver provides three different performance modes
controlled through module parameter named 'perf_mode'. Below are those
performance modes:
0: Balanced - Additional high IOPS reply queues will be enabled along with
low latency queues. Interrupt coalescing will be enabled only for these
high IOPS reply queues.
1: IOPS - No additional high IOPS queues are enabled. Interrupt coalescing
will be enabled on all reply queues.
2: Latency - No additional high IOPS queues are enabled. Interrupt
coalescing will be disabled on all reply queues. This is a legacy
behavior similar to Ventura & Invader Series.
Default performance mode settings:
- Performance mode set to 'Balanced', if Aero controller is working in
16GT/s PCIe speed.
- Performance mode will be set to 'Latency' mode for all other cases.
Through module parameter 'perf_mode', user can override default performance
mode to desired one.
Captured some performance numbers with these performance modes. 4k Random
Read IO performance numbers on 24 SAS SSD drives for above three
performance modes. Performance data is from Intel Skylake and HGST SS300
(drive model SDLL1DLR400GCCA1).
IOPS:
-----------------------------------------------------------------------
|perf_mode | qd = 1 | qd = 64 | note |
|-------------|--------|---------|-------------------------------------
|balanced | 259K | 3061k | Provides max performance numbers |
| | | | both on lower QD workload & |
| | | | also on higher QD workload |
|-------------|--------|---------|-------------------------------------
|iops | 220K | 3100k | Provides max performance numbers |
| | | | only on higher QD workload. |
|-------------|--------|---------|-------------------------------------
|latency | 246k | 2226k | Provides good performance numbers |
| | | | only on lower QD worklaod. |
-----------------------------------------------------------------------
Average Latency:
-----------------------------------------------------
|perf_mode | qd = 1 | qd = 64 |
|-------------|--------------|----------------------|
|balanced | 92.05 usec | 501.12 usec |
|-------------|--------------|----------------------|
|iops | 108.40 usec | 498.10 usec |
|-------------|--------------|----------------------|
|latency | 97.10 usec | 689.26 usec |
-----------------------------------------------------
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver will use round-robin method for IO submission in batches within
the high IOPS queues when the number of in-flight ios on the target device
is larger than 8. Otherwise the driver will use low latency reply queues.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver should enable interrupt coalescing (during driver load and after
Controller Reset) for High IOPS queues by masking appropriate bits in IOC
INIT frame.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Aero controllers support balanced performance mode through the ability to
configure queues with different properties.
Reply queues with interrupt coalescing enabled are called "high iops reply
queues" and reply queues with interrupt coalescing disabled are called "low
latency reply queues".
The driver configures a combination of high iops and low latency reply
queues if:
- HBA is an AERO controller;
- MSI-X vectors supported by the HBA is 128;
- Total CPU count in the system more than high iops queue count;
- Driver is loaded with default max_msix_vectors module parameter; and
- System booted in non-kdump mode.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added driver support to allow passthrough MPI toolbox type MFI commands to
firmware based on firmware capability.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For RAID5/RAID6 volumes configured behind Aero, driver will be doing 64bit
division operations on behalf of firmware as controller's ARM CPU is very
slow in this division. Later, driver calculates Q-ARM, P-ARM and Log-ARM and
passes those values to firmware by writing these values to RAID_CONTEXT.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
RAID1 PCI bandwidth limit algorithm is not applicable to Aero as it's PCIe
Gen4 adapter.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Issue: This issue is applicable to scenario when JBOD sequence map is
unavailable (memory allocation for JBOD sequence map failed) to driver but
feature is supported by firmware. If the driver sends a JBOD IO by not
adding 255 (MAX_PHYSICAL_DEVICES - 1) to device ID when underlying firmware
supports JBOD sequence map, it will lead to the IO failure.
Fix: For JBOD IOs, driver will not use the RAID map to fetch the devhandle
if JBOD sequence map is unavailable. Driver will set Devhandle to 0xffff
and Target ID to 'device ID + 255 (MAX_PHYSICAL_DEVICES - 1)'.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Firmware does not expect FastPath IO sent through Region Lock Bypass queue.
Though firmware never exposes such settings when fastpath IO can be sent to
RL bypass queue but it's safer to remove dead code which directs fastpath
IO to RL Bypass queue.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Issue: Under certain conditions, controller goes in FAULT state after IOC
INIT fired to firmware. Such Fault can be recovered through controller
reset.
Fix: In driver probe context, if firmware fault is observed post IOC INIT,
driver would do controller reset followed by retry logic for IOC INIT
command.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On PowerPC architecture, calling disable_irq_nosync from IRQ context is not
providing the required effect.
In current megaraid_sas driver, disable_irq_nosync is being called from IRQ
context before enabling IRQ poll. But due to the issue seen on PPC, after
IRQ poll disable and legacy ISR is enabled, we are not seeing our ISR
getting called.
Fix: Call disable_irq from IRQ poll thread context instead of IRQ context.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Aero adapters provides Atomic Request Descriptor as an alternative method
for posting an entry onto a request queue. The posting of an Atomic Request
Descriptor is an atomic operation, providing a safe mechanism for multiple
processors on the host to post requests without synchronization. This
Atomic Request Descriptor format is identical to first 32 bits of Default
Request Descriptor and uses only 32 bits.
If Aero adapters support Atomic descriptor, driver should use it for
posting IOs and DCMDs to firmware.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with
memory for some number of elements for that array. For example:
struct MR_PD_CFG_SEQ_NUM_SYNC {
...
struct MR_PD_CFG_SEQ seq[1];
} __packed;
Make use of the struct_size() helper instead of an open-coded version in
order to avoid any potential type mistakes.
So, replace the following form:
sizeof(struct MR_PD_CFG_SEQ_NUM_SYNC) + (sizeof(struct MR_PD_CFG_SEQ) * (MAX_PHYSICAL_DEVICES - 1))
with:
struct_size(pd_sync, seq, MAX_PHYSICAL_DEVICES - 1)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a print to dump the interrupt status in system log for debugging.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When driver detects a firmware fault during load, dump additional
information on fault code and subcode that will help in debugging.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch enhances the existing debug prints in reset and task management
path.
These debug prints in adapter reset path helps with debugging issues
related to IO timeouts that are seen frequently in the field. Add
additional debug prints to dump the pending command frames before
initiating an adapter reset. Also, print FastPath IOs that are
outstanding.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver will use "reply descriptor post queues" in round robin fashion when
the combined MSI-X mode is not enabled. With this IO completions are
distributed and load balanced across all the available reply descriptor
post queues equally.
This is enabled only if combined MSI-X mode is not enabled in firmware.
This improves performance and also fixes soft lockups.
When load balancing is enabled, IRQ affinity from driver needs to be
disabled.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Issue Description:
We have seen cpu lock up issues from field if system has a large (more than
96) logical cpu count. SAS3.0 controller (Invader series) supports max 96
MSI-X vector and SAS3.5 product (Ventura) supports max 128 MSI-X vectors.
This may be a generic issue (if PCI device support completion on multiple
reply queues).
Let me explain it w.r.t megaraid_sas supported h/w just to simplify the
problem and possible changes to handle such issues. MegaRAID controller
supports multiple reply queues in completion path. Driver creates MSI-X
vectors for controller as "minimum of (FW supported Reply queues, Logical
CPUs)". If submitter is not interrupted via completion on same CPU, there
is a loop in the IO path. This behavior can cause hard/soft CPU lockups, IO
timeout, system sluggish etc.
Example - one CPU (e.g. CPU A) is busy submitting the IOs and another CPU
(e.g. CPU B) is busy with processing the corresponding IO's reply
descriptors from reply descriptor queue upon receiving the interrupts from
HBA. If CPU A is continuously pumping the IOs then always CPU B (which is
executing the ISR) will see the valid reply descriptors in the reply
descriptor queue and it will be continuously processing those reply
descriptor in a loop without quitting the ISR handler.
megaraid_sas driver will exit ISR handler if it finds unused reply
descriptor in the reply descriptor queue. Since CPU A will be continuously
sending the IOs, CPU B may always see a valid reply descriptor (posted by
HBA Firmware after processing the IO) in the reply descriptor queue. In
worst case, driver will not quit from this loop in the ISR handler.
Eventually, CPU lockup will be detected by watchdog.
Above mentioned behavior is not common if "rq_affinity" set to 2 or
affinity_hint is honored by irqbalancer as "exact". If rq_affinity is set
to 2, submitter will be always interrupted via completion on same CPU. If
irqbalancer is using "exact" policy, interrupt will be delivered to
submitter CPU.
Problem statement:
If CPU count to MSI-X vectors (reply descriptor Queues) count ratio is not
1:1, we still have exposure of issue explained above and for that we don't
have any solution.
Exposure of soft/hard lockup is seen if CPU count is more than MSI-X
supported by device.
If CPUs count to MSI-X vectors count ratio is not 1:1, (Other way, if
CPU counts to MSI-X vector count ratio is something like X:1, where X > 1)
then 'exact' irqbalance policy OR rq_affinity = 2 won't help to avoid CPU
hard/soft lockups. There won't be any one to one mapping between
CPU to MSI-X vector instead one MSI-X interrupt (or reply descriptor queue)
is shared with group/set of CPUs and there is a possibility of having a
loop in the IO path within that CPU group and may observe lockups.
For example: Consider a system having two NUMA nodes and each node having
four logical CPUs and also consider that number of MSI-X vectors enabled on
the HBA is two, then CPUs count to MSI-X vector count ratio as 4:1.
e.g.
MSI-X vector 0 is affinity to CPU 0, CPU 1, CPU 2 & CPU 3 of NUMA node 0 and
MSI-X vector 1 is affinity to CPU 4, CPU 5, CPU 6 & CPU 7 of NUMA node 1.
numactl --hardware
available: 2 nodes (0-1)
node 0 cpus: 0 1 2 3 --> MSI-X 0
node 0 size: 65536 MB
node 0 free: 63176 MB
node 1 cpus: 4 5 6 7 --> MSI-X 1
node 1 size: 65536 MB
node 1 free: 63176 MB
Assume that user started an application which uses all the CPUs of NUMA
node 0 for issuing the IOs. Only one CPU from affinity list (it can be any
cpu since this behavior depends upon irqbalance) CPU0 will receive the
interrupts from MSI-X 0 for all the IOs. Eventually, CPU 0 IO submission
percentage will be decreasing and ISR processing percentage will be
increasing as it is more busy with processing the interrupts. Gradually IO
submission percentage on CPU 0 will be zero and it's ISR processing
percentage will be 100% as IO loop has already formed within the
NUMA node 0, i.e. CPU 1, CPU 2 & CPU 3 will be continuously busy with
submitting the heavy IOs and only CPU 0 is busy in the ISR path as it
always find the valid reply descriptor in the reply descriptor queue.
Eventually, we will observe the hard lockup here.
Chances of occurring of hard/soft lockups are directly proportional to
value of X. If value of X is high, then chances of observing CPU lockups is
high.
Solution:
Use IRQ poll interface defined in "irq_poll.c".
megaraid_sas driver will execute ISR routine in softirq context and it will
always quit the loop based on budget provided in IRQ poll interface.
Driver will switch to IRQ poll only when more than a threshold number of
reply descriptors are handled in one ISR. Currently threshold is set as
1/4th of HBA queue depth.
In these scenarios (i.e. where CPUs count to MSI-X vectors count ratio is
X:1 (where X > 1)), IRQ poll interface will avoid CPU hard lockups due to
voluntary exit from the reply queue processing based on budget.
Note - Only one MSI-X vector is busy doing processing.
Select CONFIG_IRQ_POLL from driver Kconfig for driver compilation.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While an online controller reset(OCR) is in progress, there is short
duration where all access to controller's PCI config space from the host
needs to be blocked. This is due to a hardware limitation of MegaRAID
controllers.
With this patch, driver will block all access to controller's config space
from userland applications by calling pci_cfg_access_lock() while OCR is in
progress and unlocking after controller comes back to ready state.
Added helper function which locks the config space before initiating OCR
and wait for controller to become READY.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional change. This patch reworks code around controller reset path
which gets rid of a couple of goto labels. This is in preparation for the
next patch which adds PCI config space access locking while controller
reset is in progress.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see http www gnu org licenses
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details [based]
[from] [clk] [highbank] [c] you should have received a copy of the
gnu general public license along with this program if not see http
www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 355 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.837383322@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is mostly update of the usual drivers: qla2xxx, qedf, smartpqi,
hpsa, lpfc, ufs, mpt3sas, ibmvfc and hisi_sas. Plus number of minor
changes, spelling fixes and other trivia.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXNIK0yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishbeFAP4wsOm6
BNqDvLbF7gHAH+oSVAeENd9tepXG2xKbUHmLRgEA1wPaUxon8L8v/SSsqwewqMXP
y6CnU6aO2iaViTNBsPs=
=RX74
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: qla2xxx, qedf, smartpqi,
hpsa, lpfc, ufs, mpt3sas, ibmvfc and hisi_sas. Plus number of minor
changes, spelling fixes and other trivia"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (298 commits)
scsi: qla2xxx: Avoid that lockdep complains about unsafe locking in tcm_qla2xxx_close_session()
scsi: qla2xxx: Avoid that qlt_send_resp_ctio() corrupts memory
scsi: qla2xxx: Fix hardirq-unsafe locking
scsi: qla2xxx: Complain loudly about reference count underflow
scsi: qla2xxx: Use __le64 instead of uint32_t[2] for sending DMA addresses to firmware
scsi: qla2xxx: Introduce the dsd32 and dsd64 data structures
scsi: qla2xxx: Check the size of firmware data structures at compile time
scsi: qla2xxx: Pass little-endian values to the firmware
scsi: qla2xxx: Fix race conditions in the code for aborting SCSI commands
scsi: qla2xxx: Use an on-stack completion in qla24xx_control_vp()
scsi: qla2xxx: Make qla24xx_async_abort_cmd() static
scsi: qla2xxx: Remove unnecessary locking from the target code
scsi: qla2xxx: Remove qla_tgt_cmd.released
scsi: qla2xxx: Complain if a command is released that is owned by the firmware
scsi: qla2xxx: target: Fix offline port handling and host reset handling
scsi: qla2xxx: Fix abort handling in tcm_qla2xxx_write_pending()
scsi: qla2xxx: Fix error handling in qlt_alloc_qfull_cmd()
scsi: qla2xxx: Simplify qlt_send_term_imm_notif()
scsi: qla2xxx: Fix use-after-free issues in qla2xxx_qpair_sp_free_dma()
scsi: qla2xxx: Fix a qla24xx_enable_msix() error path
...
There are a couple of spelling mistakes in some kernel info and notice
messages. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:
@mmiowb@
@@
- mmiowb();
and invoked as:
$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done
NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core. Additionally Christoph
refactored gdth as part of the dma changes. The major mid-layer
change this time is the removal of bidi commands and with them the
whole of the osd/exofs driver and filesystem.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXIC54SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishT1GAPwJEV23
ExPiPsnuVgKj49nLTagZ3rILRQcYNbL+MNYqxQEA0cT8FHzSDBfWY5OKPNE+RQ8z
f69LpXGmMpuagKGvvd4=
=Fhy1
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core.
Additionally Christoph refactored gdth as part of the dma changes. The
major mid-layer change this time is the removal of bidi commands and
with them the whole of the osd/exofs driver and filesystem. This is a
major simplification for block and mq in particular"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (240 commits)
scsi: cxgb4i: validate tcp sequence number only if chip version <= T5
scsi: cxgb4i: get pf number from lldi->pf
scsi: core: replace GFP_ATOMIC with GFP_KERNEL in scsi_scan.c
scsi: mpt3sas: Add missing breaks in switch statements
scsi: aacraid: Fix missing break in switch statement
scsi: kill command serial number
scsi: csiostor: drop serial_number usage
scsi: mvumi: use request tag instead of serial_number
scsi: dpt_i2o: remove serial number usage
scsi: st: osst: Remove negative constant left-shifts
scsi: ufs-bsg: Allow reading descriptors
scsi: ufs: Allow reading descriptor via raw upiu
scsi: ufs-bsg: Change the calling convention for write descriptor
scsi: ufs: Remove unused device quirks
Revert "scsi: ufs: disable vccq if it's not needed by UFS device"
scsi: megaraid_sas: Remove a bunch of set but not used variables
scsi: clean obsolete return values of eh_timed_out
scsi: sd: Optimal I/O size should be a multiple of physical block size
scsi: MAINTAINERS: SCSI initiator and target tweaks
scsi: fcoe: make use of fip_mode enum complete
...
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'wait_and_poll':
drivers/scsi/megaraid/megaraid_sas_fusion.c:936:25: warning:
variable 'fusion' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_sync_map_info':
drivers/scsi/megaraid/megaraid_sas_fusion.c:1329:6: warning:
variable 'size_sync_info' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_init_adapter_fusion':
drivers/scsi/megaraid/megaraid_sas_fusion.c:1639:39: warning:
variable 'reg_set' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_is_prp_possible':
drivers/scsi/megaraid/megaraid_sas_fusion.c:1925:25: warning:
variable 'fusion' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_make_prp_nvme':
drivers/scsi/megaraid/megaraid_sas_fusion.c:2047:25: warning:
variable 'fusion' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_build_ldio_fusion':
drivers/scsi/megaraid/megaraid_sas_fusion.c:2620:42: warning:
variable 'req_desc' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_build_and_issue_cmd_fusion':
drivers/scsi/megaraid/megaraid_sas_fusion.c:3245:25: warning:
variable 'fusion' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_task_abort_fusion':
drivers/scsi/megaraid/megaraid_sas_fusion.c:4398:25: warning:
variable 'fusion' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_reset_target_fusion':
drivers/scsi/megaraid/megaraid_sas_fusion.c:4484:25: warning:
variable 'fusion' set but not used [-Wunused-but-set-variable]
They're not used anymore and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support for the new DEVICE_LIST DCMD.
Driver currently sends two separate DCMDs for getting the list of PDs and
LDs that are exposed to host. The new DCMD provides a single interface to
get a list of both PDs and LDs that are exposed to the host. Based on the
list of target IDs that are returned by this DCMD, driver will add the
devices (PD/LD) to SML. Driver will check for FW support for this new DCMD
and based on the support will either send the new DCMD or will fall back to
the earlier method of sending two separate DCMDs for PD and LD list.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A set of 17 fixes. Most of these are minor or trivial. The one fix
that may be serious is the isci one: the bug can cause hba parameters
to be set from uninitialized memory. I don't think it's exploitable,
but you never know.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXEKL0SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishVZpAQCwuPTk
fqOt4v4hJ0oUHtEBsQK3VMXSdUvWdb5Lbn3WeQD/RFYTyNxcIF7ADSWw71b+IigT
ejUrMzI8ig+nZ1jbFZ4=
=BdS/
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"A set of 17 fixes. Most of these are minor or trivial.
The one fix that may be serious is the isci one: the bug can cause hba
parameters to be set from uninitialized memory. I don't think it's
exploitable, but you never know"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: cxgb4i: add wait_for_completion()
scsi: qla1280: set 64bit coherent mask
scsi: ufs: Fix geometry descriptor size
scsi: megaraid_sas: Retry reads of outbound_intr_status reg
scsi: qedi: Add ep_state for login completion on un-reachable targets
scsi: ufs: Fix system suspend status
scsi: qla2xxx: Use correct number of vectors for online CPUs
scsi: hisi_sas: Set protection parameters prior to adding SCSI host
scsi: tcmu: avoid cmd/qfull timers updated whenever a new cmd comes
scsi: isci: initialize shost fully before calling scsi_add_host()
scsi: lpfc: lpfc_sli: Mark expected switch fall-throughs
scsi: smartpqi_init: fix boolean expression in pqi_device_remove_start
scsi: core: Synchronize request queue PM status only on successful resume
scsi: pm80xx: reduce indentation
scsi: qla4xxx: check return code of qla4xxx_copy_from_fwddb_param
scsi: megaraid_sas: correct an info message
scsi: target/iscsi: fix error msg typo when create lio_qr_cache failed
scsi: sd: Fix cache_type_store()
commit 272652fcbf ("scsi: megaraid_sas: add retry logic in megasas_readl")
missed changing readl to megasas_readl in megasas_clear_intr_fusion(). For
Aero controllers, reads of outbound_intr_status register needs to be
retried.
Reported-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Due to hardware errata in Aero controllers, reads to certain fusion
registers could intermittently return zero. This behavior is
transient in nature and subsequent reads will return valid value.
For Aero controllers, any calls to readl to read from certain
registers will be retried for maximum three times, if read returns
zero.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of the register address, pass the instance pointer to clear_intr
and read_fw_status_reg functions. This is done in preparation for adding
adapter type based checks in these functions in later patches of this
series.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation for the new Aero series adapter type, all the places where
we check adapter type for Ventura series needs to include any later adapter
types.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NULL check before some freeing functions is not needed.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that, in this particular case, I replaced "Fall thru" with a "Fall
through" annotation and added a dash as a token in order to separate the
"Fall through" annotation from the rest of the comment on the same line,
which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
IOC INIT frame needs to be fired with a timeout of 180 seconds.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Tomas Henzl