FC-NVMe-2 added support for sequence level error recovery in the FC-NVME
protocol. This allows for the detection of errors and lost frames and
immediate retransmission of data to avoid exchange termination, which
escalates into NVMeoFC connection and association failures. A significant
RAS improvement.
The driver is modified to indicate support for SLER in the NVMe PRLI is
issues and to check for support in the PRLI response. When both sides
support it, the driver will set a bit in the WQE to enable the recovery
behavior on the exchange. The adapter will take care of all detection and
retransmission.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Typical SLI-4 hardware supports up to 2 4KB pages to be registered per XRI
to contain the exchanges Scatter/Gather List. This caps the number of SGL
elements that can be in the SGL. There are not extensions to extend the
list out of the 2 pages.
The G7 hardware adds a SGE type that allows the SGL to be vectored to a
different scatter/gather list segment. And that segment can contain a SGE
to go to another segment and so on. The initial segment must still be
pre-registered for the XRI, but it can be a much smaller amount (256Bytes)
as it can now be dynamically grown. This much smaller allocation can
handle the SG list for most normal I/O, and the dynamic aspect allows it to
support many MB's if needed.
The implementation creates a pool which contains "segments" and which is
initially sized to hold the initial small segment per xri. If an I/O
requires additional segments, they are allocated from the pool. If the
pool has no more segments, the pool is grown based on what is now
needed. After the I/O completes, the additional segments are returned to
the pool for use by other I/Os. Once allocated, the additional segments are
not released under the assumption of "if needed once, it will be needed
again". Pools are kept on a per-hardware queue basis, which is typically
1:1 per cpu, but may be shared by multiple cpus.
The switch to the smaller initial allocation significantly reduces the
memory footprint of the driver (which only grows if large ios are
issued). Based on the several K of XRIs for the adapter, the 8KB->256B
reduction can conserve 32MBs or more.
It has been observed with per-cpu resource pools that allocating a resource
on CPU A, may be put back on CPU B. While the get routines are distributed
evenly, only a limited subset of CPUs may be handling the put routines.
This can put a strain on the lpfc_put_cmd_rsp_buf_per_cpu routine because
all the resources are being put on a limited subset of CPUs.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added code to support driver loopback with MDS Diagnostics. This style of
diagnostics passes frames from the fabric to the driver who then echo them
back out the link. SEND_FRAME WQEs are used to transmit the frames. Added
the SOF and EOF field location definitions for use by SEND_FRAME.
Also ensure that enable_mds_diags is a RW parameter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To aid better hardware detection when there are issues, report the first
and second level hardware revisions from the READ_REV command. Add the
elements to the existing hardware id string.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In order to see real addresses, convert %p with %px for kernel addresses
and replace %p with %pf for functions.
While converting, standardize on "x%px" throughout (not %px or 0x%px).
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While performing code review, several relatively simple optimizations can
be done in the fast path.
Add these optimizations (unlikely designators).
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Running on Coverity produced the following errors:
- coding style (indentation)
- memset size mismatch errors
note: comment cases where it is purposely a mismatch
Fix the errors.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
modinfo for lpfc_nvme_enable_fb is incorrect. FirstBurst on lpfc target is
not fully supported.
Update the attribute description
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is allowing the user to change lpfc_enable_bg while loading the
driver against a FCoE adapter. This is not supported.
No check is made for the adapter type when applying the blockguard
enablement value.
Fix by verifying the adapter type before setting the enablement flag.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
GetTrunkInfo is displaying an incorrect link speed when the link is a trunk
and the link has gone down. The driver is not clearing the logical speed
as part of the link down transition.
Fix by setting the logical speed to UNKNOWN SPEED when the link goes down.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Max Frame Size value is shown as 34816 in fdmishow from Switch.
The driver uses bbRcvSize in common service param which is obtained from
the READ_SPARM mailbox command. The bbRcvSize field which is displayed is a
three nibble field but the driver is printing a full four nibbles.
Fix by masking off the upper nibble.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The scsi transport fc bsg interface does not expect the bsg_job_done()
callback to be done if the bsg request call returns failure. Several of the
HST_VENDOR cases in the driver unconditionally call bsg_job_done()
regardless of the returning value.
Fix the code to only call bsg_job_done() if the call to lpfc_bsg_request()
will return success.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When forcing the use of MSI (vs MSI-X) the driver is crashing in
pci_irq_get_affinity.
The driver was not using the new pci_alloc_irq_vectors interface in the MSI
path.
Fix by using pci_alloc_irq_vectors() with PCI_RQ_MSI in the MSI path.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is currently reporting a non-zero nvme sg_seg_cnt value of 256
when nvme is disabled. It should be zero.
Fix by ensuring the value is cleared.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If an unsolicited ABTS was received, the driver looks up the exchange it
references. It it does various searches looking for the exchange
context. When one is eventually matched and it is associated with an XRI
context, the driver sends an ABORT WQE to terminate the exchange. Current
code looks at whether the transport had taken action on the XRI yet or not
(no action if set to LPFC_NVMET_STE_RCV; action if non-LPFC_NVMET_STE_RCV).
Based on action or not one of two (sol vs unsol) issue abort routines are
called. The unsol version cheats and transmits a sequence containing an
ABTS with no interaction with the adapter. The sol version issues an Abort
WQE and lets the adapter manage whether the ABTS is sent to not.
The issue is the unsol version is sending ABTS unconditionally for the
exchange that received the ABTS. It's unnecessary.
Remove the conditional and just call the adapter command-based routine to
let the adapter manage the ABTS.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As part of firmware download, the adapter is reset. On the adapter the
reset causes the function to stop and all outstanding io is terminated
(without responses). The reset path then starts teardown of the adapter,
starting with deregistration of the remote ports with the nvme-fc
transport. The local port is then deregistered and the driver waits for
local port deregistration. This never finishes.
The remote port deregistrations terminated the nvme controllers, causing
them to send aborts for all the outstanding io. The aborts were serviced in
the driver, but stalled due to its state. The nvme layer then stops to
reclaim it's outstanding io before continuing. The io must be returned
before the reset on the controller is deemed complete and the controller
delete performed. The remote port deregistration won't complete until all
the controllers are terminated. And the local port deregistration won't
complete until all controllers and remote ports are terminated. Thus things
hang.
The issue is the reset which stopped the adapter also stopped all the
responses that would drive i/o completions, and the aborts were also
stopped that stopped i/o completions. The driver, when resetting the
adapter like this, needs to be generating the completions as part of the
adapter reset so that I/O complete (in error), and any aborts are not
queued.
Fix by adding flush routines whenever the adapter port has been reset or
discovered in error. The flush routines will generate the completions for
the scsi and nvme outstanding io. The abort ios, if waiting, will be caught
and flushed as well.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This issue is specific to SLI-3 adapters, specifically when DIF is used.
Once seen, this message floods the logs:
9064 BLKGRD: lpfc_scsi_prep_dma_buf_s3: Too many sg segments from
dma_map_sg
The driver, upon detecting an error such as too many elements in an sglist,
misrepresents the error by treating it as a temporary resource issue by
returning MLQUEUE_HOST_BUSY. In these cases, no retry will fix it and it
should have been a hard error. The repeated retry was causing the spamming
of the log.
As for the initial reason of why an I/O encountered this issue at all is
not clear as parameters set by the driver should have avoided this. The
dm multipath maintainer has been notified of the issue.
Fix by changing the return code for the dma mapping routines to indicate
cases that are not retryable and return DID_ERROR on those cases.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the adapter encounters a condition which causes the adapter to fail
(driver must detect the failure) simultaneously to a request to the driver
to reset the adapter (such as a host_reset), the reset path will be racing
with the asynchronously-detect adapter failure path. In the failing
situation, one path has started to tear down the adapter data structures
(io_wq's) while the other path has initiated a repeat of the teardown and
is in the lpfc_sli_flush_xxx_rings path and attempting to access the
just-freed data structures.
Fix by the following:
- In cases where an adapter failure is detected, rather than explicitly
calling offline_eratt() to start the teardown, change the adapter state
and let the later calls of posted work to the slowpath thread invoke the
adapter recovery. In essence, this means all requests to reset are
serialized on the slowpath thread.
- Clean up the routine that restarts the adapter. If there is a failure
from brdreset, don't immediately error and leave things in a partial
state. Instead, ensure the adapter state is set and finish the teardown
of structures before returning.
- If in the scsi host reset handler and the board fails to reset and
restart (which can be due to parallel reset/recovery paths), instead of
hard failing and explicitly calling offline_eratt() (which gets into the
redundant path), just fail out and let the asynchronous path resolve the
adapter state.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During cable pull testing a deadlock was seen between lpfc_nlp_counters()
vs lpfc_mbox_process_link_up() vs lpfc_work_list_done(). They are all
waiting on the shost->host_lock.
Issue is all of these cases raise irq when taking out the lock but use
spin_unlock_irq() when unlocking. The unlock path is will unconditionally
re-enable interrupts in cases where irq state should be preserved. The
re-enablement allowed the other paths to execute which then causes the
deadlock.
Fix by converting the lock/unlock to irqsave/irqrestore.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In a test with high nvme remote port counts connected via a multi-hop FC
switch config where switches were systematically reset (e.g. fabric
partitioning and re-establishment), the nvme remote ports would switch
addresses based on the switch reconfiguration events. The driver would get
into a situation where the nvme port changed address, PLOGI and PRLI would
succeed nvme transport registration occurred, but subsequent LS requests by
the nvme subsystem failed due to a bad ndlp state and connectivity to the
device failed.
The driver hit a race condition on multiple devices that address swapped
simultaneously. In cases where the driver notices the remote port structure
came back as the same value as previously (meaning a nvme_rport structure
was re-enabled and did not go through devloss_tmo/connect_tmo_failures on
all controllers) the driver would unconditionally exit assuming the ndlp
information was correct. But, if the ndlp's had been swapped, the ndlp had
stale port state information, which when used by the LS request commands,
would fail the commands.
Fix by checking whether a node swap had occurred, and only exit if no ndlp
swap had occurred.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In situations where zoning is not being used, thus NVMe initiators see
other NVMe initiators as well as NVMe targets, a link bounce on an
initiator will cause the NVMe initiators to spew "6169" State Error
messages.
The driver is not qualifying whether the remote port is a NVMe targer or
not before calling the lpfc_nvme_rescan_port(), which validates the role
and prints the message if its only an NVMe initiator.
Fix by the following:
- Before calling lpfc_nvme_rescan_port() ensure that the node is a NVMe
storage target or a NVMe discovery controller.
- Clean up implementation of lpfc_nvme_rescan_port. remoteport pointer
will always be NULL if a NVMe initiator only. But, grabbing of
remoteport pointer should be done under lock to coincide with the
registering of the remote port with the fc transport.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On an SLI-3 adapter which does not support NVMe, but with the driver global
attribute to enable nvme on any adapter if it does support NVMe
(e.g. module parameter lpfc_enable_fc4_type=3), the SGL and total SGE
values are being munged by the protocol enablement when it shouldn't be.
Correct by changing the location of where the NVME sgl information is being
applied, which will avoid any SLI-3-based adapter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If admin changes the devloss_tmo on an rport via the fc_remote_port rport
dev_loss_tmo attribute, the value is on set on scsi stack. The change is
not propagated to NVMe.
The set routine in the lldd lacks the call to
nvme_fc_set_remoteport_devloss() to set the value.
Fix by adding the call to the lldd set routine.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In tests with remote ports contantly logging out/logging coupled with
occassional local link bounce, if a remote port is disocnnected for longer
than devloss_tmo and then subsequently reconnected, eventually the test
will fail to login with the remote port and remote port connectivity is
lost.
When devloss_tmo expires, the driver does not free the node struct until
the port or npiv instances is being deleted. The node is left allocated but
the state set to UNUSED. If the node was in the process of logging in when
the local link drop occurred, meaning the RPI was allocated for the node in
order to send the ELS, but not yet registered which comes after successful
login, the node is moved to the NPR state, and if devloss expires, to
UNUSED state. If the remote port comes back, the node associated with it
is restarted and this path happens to allocate a new RPI and overwrites the
prior RPI value. In the cases where the port was logged in and loggs out,
the path did release the RPI but did not set the node rpi value. In the
cases where the remote port never finished logging in, the path never did
the call to release the rpi. In this latter case, when the node is
subsequently restore, the new rpi allocation overwrites the rpi that was
not released, and the rpi is now leaked. Eventually the port will run out
of RPI resources to log into new remote ports.
Fix by following changes:
- When an rpi is released, do so under locks and ensure the node rpi value
is set to a non-allocated value (LPFC_RPI_ALLOC_ERROR). Note:
refactored to a small service routine to avoid indentation issues.
- When re-enabling a node, check the rpi value to determine if a new
allocation is necessary. If already set, use the prior rpi.
Enhanced logging to help in the future.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a remote port is removed and remains removed for devloss_tmo, if an RSCN
is subsequently received indicating the presence of the remte port, the
driver does not login to and rediscovery the remote port.
Currently, in order to for a port to be rediscovered post an RSCN, the node
state must be NPR to reflect not logged in. When devloss expires, the node
state is marked UNUSED. When an RSCN occurs, the nodes referenced by the
RSCN will have a NPR_2B_DISC flag set, but the re-login will only be
attempted if the node is in NPR_NODE state. Thus the node is skipped over.
Fix by recognizing the NPR_2B_DISC and UNUSED and transition the node back
to NPR state to allow the re-login to take place.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If an admin updates lpfc's devloss_tmo sysfs attribute, the kernel will
oops.
Coding of a loop allowed a new value (rport) to be set/checked for null
followed by an older value (remoteport) checked for null to allow progress
where the new value, even though null, will be referenced.
Rework the logic to validate and prevent any reference to the null ptr.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It's possible for the driver to initiate an FLOGI and before it completes,
another link down/up transition occurs requiring a new FLOGI. Currently,
nothing is done to abort/noop the older FLOGI request to the adapter, so if
this transition occurs and the FLOGI completion is received after the link
down/up transition, the driver may erroneously act on the older FLOGI. In
most cases, the adapter properly terminates/fails the FLOGI, but there is a
timing condition where the FLOGI may complete on the wire prior to the
transition, but the response may not be seen/processed by the driver before
the driver sees the link transition.
Fix by having the link down handler in the driver run through any
outstanding ELS's and change the completion handler of the ELS so that it
will be no-op'd and released.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When tearing down the adapter for a reset, online/offline, or driver
unload, the queue free routine would hit a GPF oops. This only occurs on
conditions where the number of hardware queues created is fewer than the
number of cpus in the system. In this condition cpus share a hardware
queue. And of course, it's the 2nd cpu that shares a hardware that
attempted to free it a second time and hit the oops.
Fix by reworking the cpu to hardware queue mapping such that:
Assignment of hardware queues to cpus occur in two passes:
first pass: is first time assignment of a hardware queue to a cpu.
This will set the LPFC_CPU_FIRST_IRQ flag for the cpu.
second pass: for cpus that did not get a hardware queue they will
be assigned one from a primary cpu (one set in first pass).
Deletion of hardware queues is driven by cpu itteration, and queues
will only be deleted if the LPFC_CPU_FIRST_IRQ flag is set.
Also contains a few small cleanup fixes and a little better logging.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The adapter reset path (lpfc_sli_hba_down) is taking/releasing a lock with
irq. But, the path is already under the hbalock which raised irq so it's
unnecessary.
Convert to simple lock/unlock.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
lpfc_nvme_register_port hit a null prev_ndlp pointer in a test with lots of
target ports swapping addresses. The oldport value was stale, thus it's
ndlp (prev_ndlp set to it) was used.
Fix by moving oldrport pointer checks, and if used prev_ndlp pointer
assignment, to be done while the lock is held.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is inadvertently trying to issue an INIT_VPI mailbox command on
an SLI-3 driver. The command is specific to SLI-4. When the call is made to
send the command, if on an SLI-3 adapter, an array pointer is NULL and the
driver will oops.
Fix by restricting the command to SLI-4 adapters only.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a target issues an ADISC to the port and the target is a NVME target,
the driver is inadvertantly invalidating the login and marking the remote
port as logged out. Communication with the target is lost.
Revise the ADISC check so that FCP or NVME targets will be marked valid at
the end of ADISC processing. Enhance logging to recognize condition
better.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some remote ports may be slow in registering their GID_FT protocol
information with the fabric. If the remote port is an initiator, it may
send PLOGI to the port before the GID_FT logic is complete. Meaning, after
accepting the PLOGI, when the driver may see no response to the GID_FT that
is issued after the login to determine the protocols supported so that
proper PRLI's may be transmit. If the driver has no fc4 information, it
currently stops and the remote port is not discovered.
Fix by issuing a LOGO when there is no GID_FT information. The LOGO
completion handling will attempt to re-login if the nport_id is still
present.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In cases of remote-port-side cable pull/replug, there happens to be a
target that upon replug will send the port a PLOGI, a PRLI, and a LOGO.
When this sequence is received by the driver, the PLOGI accepted and a
GFT_ID is issued to find the protocol support for the remote port. While
the GFT_ID is outstanding, a LOGO is received. The driver logs the remote
port out and unregisters the RPI and schedules a new PLOGI transmission.
However, the GFT_ID was not terminated. When it completed, the driver
attempted to transition the remote port to PRLI transmission, which cancels
the PLOGI scheduling. The PRLI transmit attempt is rejected by the adapter
as the remote port is not logged in. No retry is attempted as it's expected
the logout is noted and the supposedly scheduled PLOGI should address the
state. As there is no PLOGI, the remote port does not get re-discovered.
Fix by aborting the outstanding GFT_ID if the related remote port is logged
out.
Ensure a PRLI transmit attempt only occurs if the remote port is logging
in. This avoids the incorrect attempt while logged out.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the adapter is reset while there are outstanding ELS's, subsequent
reinitialization of the adapter will fail as it has not recovered all of
the io contexts relative to the ELS's.
If an ELS timed out or otherwise failed and an the ELS was attempted to be
aborted (which changes the ELS completion context), in causes where the
driver generates completions for the outstanding IO as the adapter would
not due to being reset, the driver released only the ELS context and failed
to release the abort context. When the adapter went to reinit, as it had
not received all of the contexts, it failed to reinit.
Fix by having the ELS completion handler identify the driver-generated
completion status and release the abort context.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Unusually high IO latency can be observed with little IO in progress. The
latency may remain high regardless of amount of IO and can only be cleared
by forcing lpfc_fcp_imax values to non-zero and then back to zero.
The driver's eq_delay mechanism that scales the interrupt coalescing based
on io completion load failed to reduce or turn off coalescing when load
decreased. Specifically, if no io completed on a cpu within an eq_delay
polling window, the eq delay processing was skipped and no change was made
to the coalescing values. This left the coalescing values set when they
were no longer applicable.
Fix by always clearing the percpu counters for each time period and always
run the eq_delay calculations if an eq has a non-zero coalescing value.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a timer routine uses workqueues, it could fire before the workqueue is
allocated.
Fix by allocating the workqueue before the timer routines are setup
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After seeing some interoperability issues with ADISC, it was determined the
ELS definitions in lpfc were using types that allowed the compiler to add
pad to the structure, causing the structure to no longer be per spec. The
offending structures are ADISC, FAN, and RNID.
This patch implements the simple fix of eliminating the pad by forcing the
compiler to pack the structure. Care was taken to ensure field accesses
won't be by operations that would hit a bad field alignment.
The better solution would be to convert to the uapi fc header definitions,
but the number of changes required to do is rather intrusive so this course
of action was deferred.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When connected to a high number of remote ports, the driver is encountering
PLOGI errors. The errors are due to adapter detected failures indicating
illegal field values.
Turns out the driver was prematurely clearing an RPI bitmask before waiting
for an UNREG_RPI mailbox completion. This allowed the RPI to be reused
before it was actually available.
Fix by clearing RPI bitmask only after UNREG_RPI mailbox completion.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi-mq operation inherently performs pre-allocation of resources for
blk-mq request queues. Even though the kdump environment reduces the
configuration to a single CPU, thus 1 hardware queue, which helps
significantly, the resources are still rather large due to the per request
allocations. blk-mq pre-allocations can be over 4KB per request. With
adapter can_queue values in the 4k or 8k range, this can easily be 32MBs
before any other driver memory is factored in. Driver SGL DMA buffer
allocation can be up to 8KB per request as well adding an additional
64MB. Totals are well over 100MB for a single shost. Given kdump memory
auto-sizing utilities don't accommodate this amount of memory well, it's
very possible for kdump to fail due to lack of memory.
Fix by having the driver recognize that it is booting within a kdump
context and reduce the number of requests it will support to a more
reasonable value.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As dma_pool_destroy and mempool_destroy functions has NULL check. We may
not need NULL check before calling them.
Fix below warnings reported by coccicheck
./drivers/scsi/lpfc/lpfc_mem.c:252:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:255:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:258:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:261:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:265:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:269:2-17: WARNING: NULL check before some
freeing functions is not needed.
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When SCSI-MQ is enabled, the SCSI-MQ layers will do pre-allocation of MQ
resources based on shost values set by the driver. In newer cases of the
driver, which attempts to set nr_hw_queues to the cpu count, the
multipliers become excessive, with a single shost having SCSI-MQ
pre-allocation reaching into the multiple GBytes range. NPIV, which
creates additional shosts, only multiply this overhead. On lower-memory
systems, this can exhaust system memory very quickly, resulting in a system
crash or failures in the driver or elsewhere due to low memory conditions.
After testing several scenarios, the situation can be mitigated by limiting
the value set in shost->nr_hw_queues to 4. Although the shost values were
changed, the driver still had per-cpu hardware queues of its own that
allowed parallelization per-cpu. Testing revealed that even with the
smallish number for nr_hw_queues for SCSI-MQ, performance levels remained
near maximum with the within-driver affiinitization.
A module parameter was created to allow the value set for the nr_hw_queues
to be tunable.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As spin_unlock_irq will enable interrupts.
Function lpfc_findnode_rpi is called from
lpfc_sli_abts_err_handler (./drivers/scsi/lpfc/lpfc_sli.c)
<- lpfc_sli_async_event_handler
<- lpfc_sli_process_unsol_iocb
<- lpfc_sli_handle_fast_ring_event
<- lpfc_sli_fp_intr_handler
<- lpfc_sli_intr_handler
and lpfc_sli_intr_handler is an interrupt handler.
Interrupts are enabled in interrupt handler. Use
spin_lock_irqsave/spin_unlock_irqrestore instead of spin_(un)lock_irq in
IRQ context to avoid this.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove the redundant initialization code.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a configurations runs with a single cpu (such as a kdump kernel),
which causes the driver to request a single vector, when the driver
subsequently requests an irq affinity mask, the mask comes back null. The
driver currently does nothing in this scenario, which leaves mappings to
hardware queues incomplete and crashes the system.
Fix by recognizing the null mask and assigning the vector to the first cpu
in the system.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A null check before a kfree is redundant, so remove it. This is detected
by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is the final round of mostly small fixes in our initial submit.
It's mostly minor fixes and driver updates. The only change of note
is adding a virt_boundary_mask to the SCSI host and host template to
parametrise this for NVMe devices instead of having them do a call in
slave_alloc. It's a fairly straightforward conversion except in the
two NVMe handling drivers that didn't set it who now have a virtual
infinity parameter added.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXTJS/yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishQTNAQCsTdkA
IN1BvDBbE+KO8mvL5DuRxLtnDU6Pq5K6fkrE3gD/a1GkqyPPaJIuspq7fQY87DH/
o7VsJd/5uGphIE2Ls+M=
=38XV
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is the final round of mostly small fixes in our initial submit.
It's mostly minor fixes and driver updates. The only change of note is
adding a virt_boundary_mask to the SCSI host and host template to
parametrise this for NVMe devices instead of having them do a call in
slave_alloc. It's a fairly straightforward conversion except in the
two NVMe handling drivers that didn't set it who now have a virtual
infinity parameter added"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
scsi: megaraid_sas: set an unlimited max_segment_size
scsi: mpt3sas: set an unlimited max_segment_size for SAS 3.0 HBAs
scsi: IB/srp: set virt_boundary_mask in the scsi host
scsi: IB/iser: set virt_boundary_mask in the scsi host
scsi: storvsc: set virt_boundary_mask in the scsi host template
scsi: ufshcd: set max_segment_size in the scsi host template
scsi: core: take the DMA max mapping size into account
scsi: core: add a host / host template field for the virt boundary
scsi: core: Fix race on creating sense cache
scsi: sd_zbc: Fix compilation warning
scsi: libfc: fix null pointer dereference on a null lport
scsi: zfcp: fix GCC compiler warning emitted with -Wmaybe-uninitialized
scsi: zfcp: fix request object use-after-free in send path causing wrong traces
scsi: zfcp: fix request object use-after-free in send path causing seqno errors
scsi: megaraid_sas: Update driver version to 07.710.50.00
scsi: megaraid_sas: Add module parameter for FW Async event logging
scsi: megaraid_sas: Enable msix_load_balance for Invader and later controllers
scsi: megaraid_sas: Fix calculation of target ID
scsi: lpfc: reduce stack size with CONFIG_GCC_PLUGIN_STRUCTLEAK_VERBOSE
scsi: devinfo: BLIST_TRY_VPD_PAGES for SanDisk Cruzer Blade
...
Merge updates from Andrew Morton:
"Am experimenting with splitting MM up into identifiable subsystems
perhaps with a view to gitifying it in complex ways. Also with more
verbose "incoming" emails.
Most of MM is here and a few other trees.
Subsystems affected by this patch series:
- hotfixes
- iommu
- scripts
- arch/sh
- ocfs2
- mm:slab-generic
- mm:slub
- mm:kmemleak
- mm:kasan
- mm:cleanups
- mm:debug
- mm:pagecache
- mm:swap
- mm:memcg
- mm:gup
- mm:pagemap
- mm:infrastructure
- mm:vmalloc
- mm:initialization
- mm:pagealloc
- mm:vmscan
- mm:tools
- mm:proc
- mm:ras
- mm:oom-kill
hotfixes:
mm: vmscan: scan anonymous pages on file refaults
mm/nvdimm: add is_ioremap_addr and use that to check ioremap address
mm/memcontrol: fix wrong statistics in memory.stat
mm/z3fold.c: lock z3fold page before __SetPageMovable()
nilfs2: do not use unexported cpu_to_le32()/le32_to_cpu() in uapi header
MAINTAINERS: nilfs2: update email address
iommu:
include/linux/dmar.h: replace single-char identifiers in macros
scripts:
scripts/decode_stacktrace: match basepath using shell prefix operator, not regex
scripts/decode_stacktrace: look for modules with .ko.debug extension
scripts/spelling.txt: drop "sepc" from the misspelling list
scripts/spelling.txt: add spelling fix for prohibited
scripts/decode_stacktrace: Accept dash/underscore in modules
scripts/spelling.txt: add more spellings to spelling.txt
arch/sh:
arch/sh/configs/sdk7786_defconfig: remove CONFIG_LOGFS
sh: config: remove left-over BACKLIGHT_LCD_SUPPORT
sh: prevent warnings when using iounmap
ocfs2:
fs: ocfs: fix spelling mistake "hearbeating" -> "heartbeat"
ocfs2/dlm: use struct_size() helper
ocfs2: add last unlock times in locking_state
ocfs2: add locking filter debugfs file
ocfs2: add first lock wait time in locking_state
ocfs: no need to check return value of debugfs_create functions
fs/ocfs2/dlmglue.c: unneeded variable: "status"
ocfs2: use kmemdup rather than duplicating its implementation
mm:slab-generic:
Patch series "mm/slab: Improved sanity checking":
mm/slab: validate cache membership under freelist hardening
mm/slab: sanity-check page type when looking up cache
lkdtm/heap: add tests for freelist hardening
mm:slub:
mm/slub.c: avoid double string traverse in kmem_cache_flags()
slub: don't panic for memcg kmem cache creation failure
mm:kmemleak:
mm/kmemleak.c: fix check for softirq context
mm/kmemleak.c: change error at _write when kmemleak is disabled
docs: kmemleak: add more documentation details
mm:kasan:
mm/kasan: print frame description for stack bugs
Patch series "Bitops instrumentation for KASAN", v5:
lib/test_kasan: add bitops tests
x86: use static_cpu_has in uaccess region to avoid instrumentation
asm-generic, x86: add bitops instrumentation for KASAN
Patch series "mm/kasan: Add object validation in ksize()", v3:
mm/kasan: introduce __kasan_check_{read,write}
mm/kasan: change kasan_check_{read,write} to return boolean
lib/test_kasan: Add test for double-kzfree detection
mm/slab: refactor common ksize KASAN logic into slab_common.c
mm/kasan: add object validation in ksize()
mm:cleanups:
include/linux/pfn_t.h: remove pfn_t_to_virt()
Patch series "remove ARCH_SELECT_MEMORY_MODEL where it has no effect":
arm: remove ARCH_SELECT_MEMORY_MODEL
s390: remove ARCH_SELECT_MEMORY_MODEL
sparc: remove ARCH_SELECT_MEMORY_MODEL
mm/gup.c: make follow_page_mask() static
mm/memory.c: trivial clean up in insert_page()
mm: make !CONFIG_HUGE_PAGE wrappers into static inlines
include/linux/mm_types.h: ifdef struct vm_area_struct::swap_readahead_info
mm: remove the account_page_dirtied export
mm/page_isolation.c: change the prototype of undo_isolate_page_range()
include/linux/vmpressure.h: use spinlock_t instead of struct spinlock
mm: remove the exporting of totalram_pages
include/linux/pagemap.h: document trylock_page() return value
mm:debug:
mm/failslab.c: by default, do not fail allocations with direct reclaim only
Patch series "debug_pagealloc improvements":
mm, debug_pagelloc: use static keys to enable debugging
mm, page_alloc: more extensive free page checking with debug_pagealloc
mm, debug_pagealloc: use a page type instead of page_ext flag
mm:pagecache:
Patch series "fix filler_t callback type mismatches", v2:
mm/filemap.c: fix an overly long line in read_cache_page
mm/filemap: don't cast ->readpage to filler_t for do_read_cache_page
jffs2: pass the correct prototype to read_cache_page
9p: pass the correct prototype to read_cache_page
mm/filemap.c: correct the comment about VM_FAULT_RETRY
mm:swap:
mm, swap: fix race between swapoff and some swap operations
mm/swap_state.c: simplify total_swapcache_pages() with get_swap_device()
mm, swap: use rbtree for swap_extent
mm/mincore.c: fix race between swapoff and mincore
mm:memcg:
memcg, oom: no oom-kill for __GFP_RETRY_MAYFAIL
memcg, fsnotify: no oom-kill for remote memcg charging
mm, memcg: introduce memory.events.local
mm: memcontrol: dump memory.stat during cgroup OOM
Patch series "mm: reparent slab memory on cgroup removal", v7:
mm: memcg/slab: postpone kmem_cache memcg pointer initialization to memcg_link_cache()
mm: memcg/slab: rename slab delayed deactivation functions and fields
mm: memcg/slab: generalize postponed non-root kmem_cache deactivation
mm: memcg/slab: introduce __memcg_kmem_uncharge_memcg()
mm: memcg/slab: unify SLAB and SLUB page accounting
mm: memcg/slab: don't check the dying flag on kmem_cache creation
mm: memcg/slab: synchronize access to kmem_cache dying flag using a spinlock
mm: memcg/slab: rework non-root kmem_cache lifecycle management
mm: memcg/slab: stop setting page->mem_cgroup pointer for slab pages
mm: memcg/slab: reparent memcg kmem_caches on cgroup removal
mm, memcg: add a memcg_slabinfo debugfs file
mm:gup:
Patch series "switch the remaining architectures to use generic GUP", v4:
mm: use untagged_addr() for get_user_pages_fast addresses
mm: simplify gup_fast_permitted
mm: lift the x86_32 PAE version of gup_get_pte to common code
MIPS: use the generic get_user_pages_fast code
sh: add the missing pud_page definition
sh: use the generic get_user_pages_fast code
sparc64: add the missing pgd_page definition
sparc64: define untagged_addr()
sparc64: use the generic get_user_pages_fast code
mm: rename CONFIG_HAVE_GENERIC_GUP to CONFIG_HAVE_FAST_GUP
mm: reorder code blocks in gup.c
mm: consolidate the get_user_pages* implementations
mm: validate get_user_pages_fast flags
mm: move the powerpc hugepd code to mm/gup.c
mm: switch gup_hugepte to use try_get_compound_head
mm: mark the page referenced in gup_hugepte
mm/gup: speed up check_and_migrate_cma_pages() on huge page
mm/gup.c: remove some BUG_ONs from get_gate_page()
mm/gup.c: mark undo_dev_pagemap as __maybe_unused
mm:pagemap:
asm-generic, x86: introduce generic pte_{alloc,free}_one[_kernel]
alpha: switch to generic version of pte allocation
arm: switch to generic version of pte allocation
arm64: switch to generic version of pte allocation
csky: switch to generic version of pte allocation
m68k: sun3: switch to generic version of pte allocation
mips: switch to generic version of pte allocation
nds32: switch to generic version of pte allocation
nios2: switch to generic version of pte allocation
parisc: switch to generic version of pte allocation
riscv: switch to generic version of pte allocation
um: switch to generic version of pte allocation
unicore32: switch to generic version of pte allocation
mm/pgtable: drop pgtable_t variable from pte_fn_t functions
mm/memory.c: fail when offset == num in first check of __vm_map_pages()
mm:infrastructure:
mm/mmu_notifier: use hlist_add_head_rcu()
mm:vmalloc:
Patch series "Some cleanups for the KVA/vmalloc", v5:
mm/vmalloc.c: remove "node" argument
mm/vmalloc.c: preload a CPU with one object for split purpose
mm/vmalloc.c: get rid of one single unlink_va() when merge
mm/vmalloc.c: switch to WARN_ON() and move it under unlink_va()
mm/vmalloc.c: spelling> s/informaion/information/
mm:initialization:
mm/large system hash: use vmalloc for size > MAX_ORDER when !hashdist
mm/large system hash: clear hashdist when only one node with memory is booted
mm:pagealloc:
arm64: move jump_label_init() before parse_early_param()
Patch series "add init_on_alloc/init_on_free boot options", v10:
mm: security: introduce init_on_alloc=1 and init_on_free=1 boot options
mm: init: report memory auto-initialization features at boot time
mm:vmscan:
mm: vmscan: remove double slab pressure by inc'ing sc->nr_scanned
mm: vmscan: correct some vmscan counters for THP swapout
mm:tools:
tools/vm/slabinfo: order command line options
tools/vm/slabinfo: add partial slab listing to -X
tools/vm/slabinfo: add option to sort by partial slabs
tools/vm/slabinfo: add sorting info to help menu
mm:proc:
proc: use down_read_killable mmap_sem for /proc/pid/maps
proc: use down_read_killable mmap_sem for /proc/pid/smaps_rollup
proc: use down_read_killable mmap_sem for /proc/pid/pagemap
proc: use down_read_killable mmap_sem for /proc/pid/clear_refs
proc: use down_read_killable mmap_sem for /proc/pid/map_files
mm: use down_read_killable for locking mmap_sem in access_remote_vm
mm: smaps: split PSS into components
mm: vmalloc: show number of vmalloc pages in /proc/meminfo
mm:ras:
mm/memory-failure.c: clarify error message
mm:oom-kill:
mm: memcontrol: use CSS_TASK_ITER_PROCS at mem_cgroup_scan_tasks()
mm, oom: refactor dump_tasks for memcg OOMs
mm, oom: remove redundant task_in_mem_cgroup() check
oom: decouple mems_allowed from oom_unkillable_task
mm/oom_kill.c: remove redundant OOM score normalization in select_bad_process()"
* akpm: (147 commits)
mm/oom_kill.c: remove redundant OOM score normalization in select_bad_process()
oom: decouple mems_allowed from oom_unkillable_task
mm, oom: remove redundant task_in_mem_cgroup() check
mm, oom: refactor dump_tasks for memcg OOMs
mm: memcontrol: use CSS_TASK_ITER_PROCS at mem_cgroup_scan_tasks()
mm/memory-failure.c: clarify error message
mm: vmalloc: show number of vmalloc pages in /proc/meminfo
mm: smaps: split PSS into components
mm: use down_read_killable for locking mmap_sem in access_remote_vm
proc: use down_read_killable mmap_sem for /proc/pid/map_files
proc: use down_read_killable mmap_sem for /proc/pid/clear_refs
proc: use down_read_killable mmap_sem for /proc/pid/pagemap
proc: use down_read_killable mmap_sem for /proc/pid/smaps_rollup
proc: use down_read_killable mmap_sem for /proc/pid/maps
tools/vm/slabinfo: add sorting info to help menu
tools/vm/slabinfo: add option to sort by partial slabs
tools/vm/slabinfo: add partial slab listing to -X
tools/vm/slabinfo: order command line options
mm: vmscan: correct some vmscan counters for THP swapout
mm: vmscan: remove double slab pressure by inc'ing sc->nr_scanned
...
The RISC-V architecture has a register named the "Supervisor Exception
Program Counter", or "sepc". This abbreviation triggers checkpatch.pl's
misspelling detector, resulting in noise in the checkpatch output. The
risk that this noise could cause more useful warnings to be missed seems
to outweigh the harm of an occasional misspelling of "spec". Thus drop
the "sepc" entry from the misspelling list.
[akpm@linux-foundation.org: fix existing "sepc" instances, per Joe]
Link: http://lkml.kernel.org/r/20190518210037.13674-1-paul.walmsley@sifive.com
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The lpfc_debug_dump_all_queues() function repeatedly calls into
lpfc_debug_dump_qe() which has a temporary 128 byte buffer. This was fine
before the introduction of CONFIG_GCC_PLUGIN_STRUCTLEAK_VERBOSE because
each instance could occupy the same stack slot. However, now they each get
their own copy, which leads to a huge increase in stack usage as seen from
the compiler warning:
drivers/scsi/lpfc/lpfc_debugfs.c: In function 'lpfc_debug_dump_all_queues':
drivers/scsi/lpfc/lpfc_debugfs.c:6474:1: error: the frame size of 1712 bytes is larger than 100 bytes [-Werror=frame-larger-than=]
Avoid this by not marking lpfc_debug_dump_qe() as inline so the compiler
can choose to emit a static version of this function when it's needed or
otherwise silently drop it. As an added benefit, not inlining multiple
copies of this function means we save several kilobytes of .text section,
reducing the file size from 47kb to 43.
It is somewhat unusual to have a function that is static but not inline in
a header file, but this does not cause problems here because it is only
used by other inline functions. It would however seem reasonable to move
all the lpfc_debug_dump_* functions into lpfc_debugfs.c and not mark them
inline as a later cleanup.
Fixes: 81a56f6dcd ("gcc-plugins: structleak: Generalize to all variable types")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This topic branch covers a fundamental change in how our sg lists are
allocated to make mq more efficient by reducing the size of the
preallocated sg list. This necessitates a large number of driver
changes because the previous guarantee that if a driver specified
SG_ALL as the size of its scatter list, it would get a non-chained
list and didn't need to bother with scatterlist iterators is now
broken and every driver *must* use scatterlist iterators.
This was broken out as a separate topic because we need to convert all
the drivers before pulling the trigger and unconverted drivers kept
being found, necessitating a rebase.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXSTzzCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishZB+AP9I8j/s
wWfg0Z3WNuf4D5I3rH4x1J3cQTqPJed+RjwgcQEA1gZvtOTg1ZEn/CYMVnaB92x0
t6MZSchIaFXeqfD+E7U=
=cv8o
-----END PGP SIGNATURE-----
Merge tag 'scsi-sg' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI scatter-gather list updates from James Bottomley:
"This topic branch covers a fundamental change in how our sg lists are
allocated to make mq more efficient by reducing the size of the
preallocated sg list.
This necessitates a large number of driver changes because the
previous guarantee that if a driver specified SG_ALL as the size of
its scatter list, it would get a non-chained list and didn't need to
bother with scatterlist iterators is now broken and every driver
*must* use scatterlist iterators.
This was broken out as a separate topic because we need to convert all
the drivers before pulling the trigger and unconverted drivers kept
being found, necessitating a rebase"
* tag 'scsi-sg' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (21 commits)
scsi: core: don't preallocate small SGL in case of NO_SG_CHAIN
scsi: lib/sg_pool.c: clear 'first_chunk' in case of no preallocation
scsi: core: avoid preallocating big SGL for data
scsi: core: avoid preallocating big SGL for protection information
scsi: lib/sg_pool.c: improve APIs for allocating sg pool
scsi: esp: use sg helper to iterate over scatterlist
scsi: NCR5380: use sg helper to iterate over scatterlist
scsi: wd33c93: use sg helper to iterate over scatterlist
scsi: ppa: use sg helper to iterate over scatterlist
scsi: pcmcia: nsp_cs: use sg helper to iterate over scatterlist
scsi: imm: use sg helper to iterate over scatterlist
scsi: aha152x: use sg helper to iterate over scatterlist
scsi: s390: zfcp_fc: use sg helper to iterate over scatterlist
scsi: staging: unisys: visorhba: use sg helper to iterate over scatterlist
scsi: usb: image: microtek: use sg helper to iterate over scatterlist
scsi: pmcraid: use sg helper to iterate over scatterlist
scsi: ipr: use sg helper to iterate over scatterlist
scsi: mvumi: use sg helper to iterate over scatterlist
scsi: lpfc: use sg helper to iterate over scatterlist
scsi: advansys: use sg helper to iterate over scatterlist
...
This is mostly update of the usual drivers: qla2xxx, hpsa, lpfc, ufs,
mpt3sas, ibmvscsi, megaraid_sas, bnx2fc and hisi_sas as well as the
removal of the osst driver (I heard from Willem privately that he
would like the driver removed because all his test hardware has
failed). Plus number of minor changes, spelling fixes and other
trivia.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXSTl4yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdcxAQDCJVbd
fPUX76/V1ldupunF97+3DTharxxbst+VnkOnCwD8D4c0KFFFOI9+F36cnMGCPegE
fjy17dQLvsJ4GsidHy8=
=aS5B
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: qla2xxx, hpsa, lpfc, ufs,
mpt3sas, ibmvscsi, megaraid_sas, bnx2fc and hisi_sas as well as the
removal of the osst driver (I heard from Willem privately that he
would like the driver removed because all his test hardware has
failed). Plus number of minor changes, spelling fixes and other
trivia.
The big merge conflict this time around is the SPDX licence tags.
Following discussion on linux-next, we believe our version to be more
accurate than the one in the tree, so the resolution is to take our
version for all the SPDX conflicts"
Note on the SPDX license tag conversion conflicts: the SCSI tree had
done its own SPDX conversion, which in some cases conflicted with the
treewide ones done by Thomas & co.
In almost all cases, the conflicts were purely syntactic: the SCSI tree
used the old-style SPDX tags ("GPL-2.0" and "GPL-2.0+") while the
treewide conversion had used the new-style ones ("GPL-2.0-only" and
"GPL-2.0-or-later").
In these cases I picked the new-style one.
In a few cases, the SPDX conversion was actually different, though. As
explained by James above, and in more detail in a pre-pull-request
thread:
"The other problem is actually substantive: In the libsas code Luben
Tuikov originally specified gpl 2.0 only by dint of stating:
* This file is licensed under GPLv2.
In all the libsas files, but then muddied the water by quoting GPLv2
verbatim (which includes the or later than language). So for these
files Christoph did the conversion to v2 only SPDX tags and Thomas
converted to v2 or later tags"
So in those cases, where the spdx tag substantially mattered, I took the
SCSI tree conversion of it, but then also took the opportunity to turn
the old-style "GPL-2.0" into a new-style "GPL-2.0-only" tag.
Similarly, when there were whitespace differences or other differences
to the comments around the copyright notices, I took the version from
the SCSI tree as being the more specific conversion.
Finally, in the spdx conversions that had no conflicts (because the
treewide ones hadn't been done for those files), I just took the SCSI
tree version as-is, even if it was old-style. The old-style conversions
are perfectly valid, even if the "-only" and "-or-later" versions are
perhaps more descriptive.
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (185 commits)
scsi: qla2xxx: move IO flush to the front of NVME rport unregistration
scsi: qla2xxx: Fix NVME cmd and LS cmd timeout race condition
scsi: qla2xxx: on session delete, return nvme cmd
scsi: qla2xxx: Fix kernel crash after disconnecting NVMe devices
scsi: megaraid_sas: Update driver version to 07.710.06.00-rc1
scsi: megaraid_sas: Introduce various Aero performance modes
scsi: megaraid_sas: Use high IOPS queues based on IO workload
scsi: megaraid_sas: Set affinity for high IOPS reply queues
scsi: megaraid_sas: Enable coalescing for high IOPS queues
scsi: megaraid_sas: Add support for High IOPS queues
scsi: megaraid_sas: Add support for MPI toolbox commands
scsi: megaraid_sas: Offload Aero RAID5/6 division calculations to driver
scsi: megaraid_sas: RAID1 PCI bandwidth limit algorithm is applicable for only Ventura
scsi: megaraid_sas: megaraid_sas: Add check for count returned by HOST_DEVICE_LIST DCMD
scsi: megaraid_sas: Handle sequence JBOD map failure at driver level
scsi: megaraid_sas: Don't send FPIO to RL Bypass queue
scsi: megaraid_sas: In probe context, retry IOC INIT once if firmware is in fault
scsi: megaraid_sas: Release Mutex lock before OCR in case of DCMD timeout
scsi: megaraid_sas: Call disable_irq from process IRQ poll
scsi: megaraid_sas: Remove few debug counters from IO path
...
To support scenarios which aren't bound to nvmetcli add port scenarios,
which is currently where the nvmet_fc transport invokes the discovery
event callbacks, a syfs attribute is added to lpfc which can be written
to cause an RSCN to be generated for the nport.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch updates RSCN receive processing to check for the remote
port being an NVME port, and if so, invoke the nvme_fc callback to
rescan the remote port. The rescan will generate a discovery udev
event.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch adds support for the nvmet discovery op. When the callback
routine is called, the driver will call the routine to generate an RSCN
to the port on the other end of the link.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch adds general RSCN support:
- The ability to transmit an RSCN to the port on the other end of
the link (regular port if pt2pt, or fabric controller if fabric).
- And general recognition of an RSCN ELS when an ELS is received.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Unlike the legacy I/O path, scsi-mq preallocates a large array to hold
the scatterlist for each request. This static allocation can consume
substantial amounts of memory on modern controllers which support a
large number of concurrently outstanding requests.
To facilitate a switch to a smaller static allocation combined with a
dynamic allocation for requests that need it, we need to make sure all
SCSI drivers handle chained scatterlists correctly.
Convert remaining drivers that directly dereference the scatterlist
array to using the iterator functions.
[mkp: clarified commit message]
Reviewed by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When building powerpc pseries_defconfig or powernv_defconfig:
drivers/scsi/lpfc/lpfc_nvmet.c:224:1: error: unused function
'lpfc_nvmet_get_ctx_for_xri' [-Werror,-Wunused-function]
drivers/scsi/lpfc/lpfc_nvmet.c:246:1: error: unused function
'lpfc_nvmet_get_ctx_for_oxid' [-Werror,-Wunused-function]
These functions are only compiled when CONFIG_NVME_TARGET_FC is enabled.
Use that same condition so there is no more warning. While the fixes commit
did not introduce these functions, it caused these warnings.
Fixes: 4064b27417a7 ("scsi: lpfc: Make some symbols static")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix sparse warnings:
drivers/scsi/lpfc/lpfc_sli.c:115:1: warning: symbol 'lpfc_sli4_pcimem_bcopy' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_sli.c:7854:1: warning: symbol 'lpfc_sli4_process_missed_mbox_completions' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_nvmet.c:223:27: warning: symbol 'lpfc_nvmet_get_ctx_for_xri' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_nvmet.c:245:27: warning: symbol 'lpfc_nvmet_get_ctx_for_oxid' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_init.c:75:10: warning: symbol 'lpfc_present_cpu' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warnings:
drivers/scsi/lpfc/lpfc_init.c: In function lpfc_setup_cq_lookup:
drivers/scsi/lpfc/lpfc_init.c:9359:30: warning: variable qp set but not used [-Wunused-but-set-variable]
It's not used since commit e70596a60f88 ("scsi: lpfc: Fix poor use of
hardware queues if fewer irq vectors")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use *_pool_zalloc rather than *_pool_alloc followed by memset with 0.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.2.0.3
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kernel warnings may be seen with preempt debugging enabled.
Replace smp_processor_id calls with raw_smp_processor_id or cpu information
stored in hdwq structures.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Crashes in scsi_queue_rq or in dma_unmap_direct_sg during BFS when lpfc has
lpfc_enable_bg=1.
lpfc is setting DIX and prot sg after scsi_add_host_with_dma() has been
called. The scsi_host_set_prot() and scsi_host_set_guard() routines need to
be called before scsi_add_host_with_dma().
Revise the calling sequence to set the protection/guard data before calling
scsi_add_host_with_dma().
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
FDMI protocol support registration was not accurately showing nvme
support. The fcponly-path clears the parameter object.
Move the code out of the fcponly code path. Fix the FDMI registration data
to properly check for nvme support. Commonize the manner in which the fdmi
routines set protocol support.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Issuing a LUN reset was resulting in a command failure which then escalated
to a host reset.
The FCP-4 spec allows fcp_rsp_len field to specify the number of valid
bytes of FCP_RSP_INFO, and the value could be 4 or 8. The driver is
allowing only a value of 8, thus it failed the command.
Revise the driver to allow 4 or 8.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While fixing the resources per socket, realized the driver was not using
hardware queues (up to 1 per cpu) if there were fewer interrupt
vectors. The driver was only using the hardware queue assigned to the cpu
with the vector.
Rework the affinity map check to use the additional hardware queue elements
that had been allocated. If the cpu count exceeds the hardware queue count
- share, but choose what is shared with by: hyperthread peer, core peer,
socket peer, or finally similar cpu in a different socket.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver was coded expecting enough hardware queues and interrupt vectors
such that at least there was one per socket. In the case where there were
fewer than sockets, cpus were left unassigned thus null pointers.
Rework the affinity mappings. Map settings for the cpu's that are in the
irq cpu mask. For each cpu not in the mask, map to another cpu that does
have a mask. Choice of the "other" cpu will attempt to map to the same cpu
but differing hyperthread, or cpu within in same core, or cpu within same
socket, or finally cpu in the base socket.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Invalid logical speed is displayed for trunk enabled ports when all ports
are down. Also noted that link speed is incorrectly reported for the units
when links are up.
Current code is returning the logical link speed from the last event from
the adapter. In cases where the last link went down, the link speed in the
event was not valid - meaning that although the links where down the field
had a bogus value.
Rework the event handling to qualify the trunk link state before using the
event speed data.
Also correct units on other areas where the logical link speed was taken
from a link event.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
eq create is leaking mailbox memory if it encounters an error.
rework error path to free the memory.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver unconditionally says fw doesn't support nvme when in
truth it was a driver parameter settings that disabled nvme support.
Rework the code validating nvme support to accurately report what
condition is disabling nvme support. Save state on whether nvme
fw supports nvme in case sysfs attributes change dynamically.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a race condition with the abort handler declaring a waitq
item on it's stack, followed by a timeout in the abort handler that
has it give up on the abort return to its caller. When the io is
finally aborted and its completion handler called, it references
the waitq element that the abort_handler set up, which is no longer
valid resulting in a deadlock.
Fix by clearing the waitq reference, under lock, when the abort
handler timeout gives up. Have the completion handler validate the
waitq before referencing it.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When queued work is executed posting a new command to the transport
the driver is reporting a null buffer.
The driver had received an ABTS which matched a command that had
been scheduled for delivery to the transport. The driver proceeded
to cancel the command, but the work item was never cancelled.
Fix by cancelling the queued work item. Also turns out the ABTS
response was not properly sending a BA_ACC, so set the flag to
send the ACC.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use-after-free memory overwrite detected. Problem reported
by Ewan Milne at Red Hat after running lpfc target with additional
memory checking enabled.
Race condition when lpfc_nvmet_xmt_ls_rsp_cmp frees the ctxp
memory in interrupt context before lpfc_nvmet_xmt_ls_rsp
clears a field in the ctxp after successfully issuing the wqe.
Remove the unnecessary ctxp write after reposting the rq buffer. The
ctxp->rqb_buffer field is not checked in LS handling after the wqe
is submitted.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reported-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Under heavy load the target stops responding, the drivers aborts
timeout and we start recovery by logging out of the target, but
the target is never logged into again.
In a point-to-point scenario, there were battling PLOGI's. When we
received a PLOGI request after having sent one, the driver cancels
the processing of the original plogi. However, the completion path
of the remaining plogi was coded to skip the reg_rpi that should
be happening on the 2nd plogi.
Correct by adding a simple pt2pt check such that the 2nd plogi isn't
skipped and the reg_login occurs.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Turns out the message change in 12.2.0.1 for unsupported topology
makes the linux driver out of sync with other products.
Revert the message back to the prior content for product consistency.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver currently is relying on firmware to match ABTSs to existing
exchanges. This works fine as long as an exchange has been assigned to the
io and work posted to it. However, for unmapped frames (rxid=0xFFFF), the
driver has yet to assign an xri. The driver was blindly saying it couldn't
match the ABTS and sending the BA_xxx. However, the command frame may have
been in queues waiting on xri's before posting to the nvmet_fc layer. When
xri's became available, the command frame would still be pushed to the
transport and that io would execute, even though the io had been killed by
ABTS. The initiator, seeing the io ABTS'd, would reuse the exchange for a
different io which would be received on the target and pushed up. If the
"zombie" io then came back down and started transmitting, the initiator
would match the oxid and accept erroneous data. Bad things happened.
Add tracking of active exchanges in the target to allow matching of a
received ABTS against active or pending IO requests. If the ABTS is matched
to a pending or active IO, the drive initiates cleanup and conditionally
notifies the transport.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the driver is notified of new command frame receipt by CQEs. As
part of the CQE processing, the driver upcalls the nvmet_fc transport to
deliver the command. nvmet_fc, as part of receiving the command builds out
a context for it, where one of the first steps is to allocate memory for
the io.
When running with tests that do large ios (1MB), it was found on some
systems, the total number of outstanding I/O's, at 1MB per, completely
consumed the system's memory. Thus additional ios were getting blocked in
the memory allocator. Given that this blocked the lpfc thread processing
CQEs, there were lots of other commands that were received and which are
then held up, and given CQEs are serially processed, the aggregate delays
for an IO waiting behind the others became cummulative - enough so that the
initiator hit timeouts for the ios.
The basic fix is to avoid the direct upcall and instead schedule a work
item for each io as it is received. This allows the cq processing to
complete very quickly, and each io can then run or block on it's own.
However, this general solution hurts latency when there are few ios. As
such, implemented the fix such that the driver watches how many CQEs it has
processed sequentially in one run. As long as the count is below a
threshold, the direct nvmet_fc upcall will be made. Only when the count is
exceeded will it revert to work scheduling.
Given that debug of this showed a surprisingly long delay in cq processing,
the io timer stats were updated to better reflect the processing of the
different points.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Revise a stalled adapter message to also include the number of jobs that
are stalling the thread.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A race condition resulted in receive buffers being placed in the free list
twice.
Change the locking and handling to check whether the "other" path will be
freeing the entry in a later thread and skip it if it is.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After receiving an unsolicited ABTS (meaning rxid is 0xFFFF), the driver
used the oxid from the initiator to match against a local xri which may
have been allocated for the io. The xri would be the rxid - it's an invalid
check resulting in the command not being matched or erroneously matched.
Change the lookup to use the oxid and the SID to match against received
IO's original values.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Softlockups are seen in low memory situations. They are due to doing
oas_lun allocation with GFP_KERNEL in atomic contexts.
Change the calls to oas_lun to indicate atomic context so that GFP_ATOMIC
is used.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Due to the couple of bug fixes, update lpfc version to 12.2.0.2
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There was a missing qualification of a valid ndlp structure when calling to
send an RRQ for an abort. Add the check.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Many of the exit cases were not releasing the rcu read lock. Corrected the
exit paths.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There were a number of erroneous comments and incorrect older lockdep
checks that were causing a number of warnings.
Resolve the following:
- Inconsistent lock state warnings in lpfc_nvme_info_show().
- Fixed comments and code on sequences where ring lock is now held instead
of hbalock.
- Reworked calling sequences around lpfc_sli_iocbq_lookup(). Rather than
locking prior to the routine and have routine guess on what lock, take
the lock within the routine. The lockdep check becomes unnecessary.
- Fixed comments and removed erroneous hbalock checks.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
CC: Bart Van Assche <bvanassche@acm.org>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix sparse warning:
drivers/scsi/lpfc/lpfc_init.c:13091:1: warning:
symbol 'lpfc_sli4_oas_verify' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We have a few submissions for 5.2 that depend on fixes merged post
5.1-rc1. Merge the fixes branch into queue.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the FC-NVMe driver is leverating the SCSI FC transport class to
access the remote ports. Which means that all FC-NVMe remote ports will be
visible to the fc transport layer, but due to missing definitions the port
roles will always be 'unknown'. This patch adds the missing definitions to
the fc transport class to that the port roles are correctly displayed.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Giridhar Malavali <gmalavali@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support to recognize FPIN ELS's that are received. When
one is received, the fc transport will be called to handle the the FPIN.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that the following compiler warning is reported with
CONFIG_NVME_FC=n:
drivers/scsi/lpfc/lpfc_nvme.c:2140:1: warning: 'lpfc_nvme_lport_unreg_wait' defined but not used [-Wunused-function]
lpfc_nvme_lport_unreg_wait(struct lpfc_vport *vport,
^~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 3999df75bc ("scsi: lpfc: Declare local functions static")
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Abort thread wakeups, on some wqe types, are not happening. The thread
wakeup logic is dependent upon the LPFC_DRIVER_ABORTED flag. However, on
these wqes, the completion handler running prior to the io completion
routine ends up clearing the flag.
Rework the wakeup logic to look at a non-null waitq element which must be
set if the abort thread is waiting. This is reverting the change in the
indicated patch.
Fixes: c2017260ee ("scsi: lpfc: Rework locking on SCSI io completion")
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that a kernel warning appears when smp_processor_id() is
called with preempt debugging enabled.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove those functions that are not called from outside the removed
functions.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does not change any functionality but avoids that the compiler
complains about set-but-not-used variables when building with W=1.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Arrays should be defined in .c files instead of in a header file. This
patch reduces the size of the lpfc kernel module.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that the compiler warns about missing fall-through
annotation when building with W=1.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoid that smatch complains about misleading indentation.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that the compiler complains about missing declarations
when building with W=1.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
clang -Wuninitialized incorrectly sees a variable being used without
initialization:
drivers/scsi/lpfc/lpfc_nvme.c:2102:37: error: variable 'localport' is uninitialized when used here
[-Werror,-Wuninitialized]
lport = (struct lpfc_nvme_lport *)localport->private;
^~~~~~~~~
drivers/scsi/lpfc/lpfc_nvme.c:2059:38: note: initialize the variable 'localport' to silence this warning
struct nvme_fc_local_port *localport;
^
= NULL
1 error generated.
This is clearly in dead code, as the condition leading up to it is always
false when CONFIG_NVME_FC is disabled, and the variable is always
initialized when nvme_fc_register_localport() got called successfully.
Change the preprocessor conditional to the equivalent C construct, which
makes the code more readable and gets rid of the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change snprintf to scnprintf. There are generally two cases where using
snprintf causes problems.
1) Uses of size += snprintf(buf, SIZE - size, fmt, ...)
In this case, if snprintf would have written more characters than what the
buffer size (SIZE) is, then size will end up larger than SIZE. In later
uses of snprintf, SIZE - size will result in a negative number, leading
to problems. Note that size might already be too large by using
size = snprintf before the code reaches a case of size += snprintf.
2) If size is ultimately used as a length parameter for a copy back to user
space, then it will potentially allow for a buffer overflow and information
disclosure when size is greater than SIZE. When the size is used to index
the buffer directly, we can have memory corruption. This also means when
size = snprintf... is used, it may also cause problems since size may become
large. Copying to userspace is mitigated by the HARDENED_USERCOPY kernel
configuration.
The solution to these issues is to use scnprintf which returns the number of
characters actually written to the buffer, so the size variable will never
exceed SIZE.
Signed-off-by: Silvio Cesare <silvio.cesare@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Declaring interrupt clear routines as inline is bogus as they are used as
an indirect pointer.
Remove the inline references.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
You can't declare a function inline in a header if it doesn't have a body
available to the compiler. So realistically you either don't declare it
inline or you make it a static inline in the header. I think the latter
applies in this case, so this should be the fix
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.2.0.0
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Revise driver copyright message to show 2019. Update couple of files
modified by 12.2.0.1 patch set.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the 6072 log message string to print the whole 32 bits of the
extended status.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver had duplicated log message numbers making debug difficult.
Make all messages unique.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change the SLI4 queue creation code to use NUMA node based memory
allocation based on the cpu the queues will be related to.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the driver maintains a sideband structure which has a pointer for
each queue element. However, at 8 bytes per pointer, and up to 4k elements
per queue, and 100s of queues, this can take up a lot of memory.
Convert the driver to using an access routine that calculates the element
address based on its index rather than using the pointer table.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When in trunking mode, the adapter can be placed into diagnostic mode and
each link in the trunk tested via loopback.
Add support to the driver to perform per-link loopback testing when in
trunking mode.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver is using uint16_t and is encountering an overflow of the 16bits when
calculating link speed.
Fix by using a u32 type.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If all the trunk links drop and a single link resumes, the link_state is
not properly reported. When trunked, the driver receives two async
cqes. One acqe reports the trunk link states, which the driver records.
The other cqe reports the overall state of the trunk. In the failing case,
the trunk link state acqe preceeds the overall trunk link state acqe. The
trunk link state acqe, as it's an "up" transition, calls a code path which
ensures a down transition before moving to the up state. The down
transition had a side effect of clearing the just-saved trunk link states.
Fix by not clearing the trunk link states if we've already transitioned
to a down state.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Invalid test is allowing Loop to be a supported topology on G6 and G7
adapters. The chips do not support loop as their link speeds prohibit loop
per standard.
Correct the conditional so that loop is not reported.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is currently reporting the firmware revision not the actual boot
bios version in FDMI data.
Modify the driver to obtain the boot bios version from the adapter and use
that data in the FMDI data sent to the switch.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The switch is rejecting FDMI2 registration for symbolic name. There is a
"\n" in the name string, which the switch dislikes thus rejects the
registration.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is reporting support for NVME even when not configured for NVME
operation.
Fix (and make more readable) when NVME protocol support is indicated.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The FDMI manufacturer value being reported on Linux is inconsistent with
other OS's.
Set the value to "Emulex Corporation" for consistency.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the driver undergoes repeated host resets it starts losing exchange
structures and eventually returns SCSI_MLQUEUE_HOST_BUSY and does not
recover. The offline path is not reclaiming the outstanding ios on the fcp
pring txcmplq before calling lpfc_destroy_multixripool, which causes the
txmcplq to be reinit and the resources lost.
Flush the fcp rings before destroying the multixripools.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The adapter initialization sequence enables interrupts, initializes the
adapter link_state to LINK_DOWN, then issues commands to initialize the
adapter. The interrupt handler on the adapter validates the link_state (has
to be at least LINK_DOWN) and if invalid, will discard the interrupting
event.
In most cases, there is not a command completion, thus an interrupt until
the initialization commands have been sent which is post the setting of
state to LINK_DOWN. However, in cases of firmware reset, the reset will
modify the link_state to an invalid value (indicating a reset of the
adapter) and there occasionally are cases where the adapter will generate
an asynchronous event which shares the eq/cq used for mailbox commands. In
the failure case, an interrupt is generated immediately after enabling them
due to the async event. As link_state is invalid, the eq is list and the
CQ not serviced. At this point link_state is initialized and the mailbox
command sent. As the CQ has not been serviced, it is not armed, so no
interrupt event is generated when the mailbox command completes.
Modify the initialization sequence so that interrupts are enabled after
link_state is properly initialized, which avoids the race condition with
the async event.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It's possible for the scsi error handler to fire and call the target reset
handler simultaneously to the driver logging out and relogging into the
system. If hit just right, the re-login may not have fully re-established
the remote port and the rdata->pnod structure may be null.
Check for NULL in the reset handler and return failure if NULL.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current code incorrectly specifies a completion wait timeout duration in 5
jiffies, when it should have been 5 seconds.
Fix the adjust for units for the completion timeout call.
[mkp: manual merge]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current code is using msleep when polling for hw ready. Unfortunately the
msleep routine isn't very accurate on rescheduling. In fact, on a busy
systems which reset the adapter, it became 10s of seconds before it was
rescheduled.
Fix by busy waiting using udelay. As we're now busy waiting, significantly
reduce the wait time so that we can exit the pool loop as soon as possible.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver periodically checks for adapter error in a background thread. If
the thread detects an error, the adapter will be reset including the
deletion and reallocation of workqueues on the adapter. Simultaneously,
there may be a user-space request to offline the adapter which may try to
do many of the same steps, in parallel, on a different thread. As memory
was deallocated while unexpected, the parallel offline request hit a bad
pointer.
Add coordination between the two threads. The error recovery thread has
precedence. So, when an error is detected, a flag is set on the adapter to
indicate the error thread is terminating the adapter. But, before doing
that work, it will look for a flag that is set by the offline flow, and if
set, will wait for it to complete before then processing the error handling
path. Similarly, in the offline thread, it first checks for whether the
error thread is resetting the adapter, and if so, will then wait for the
error thread to finish. Only after it has finished, will it set its flag
and offline the adapter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In a couple of cases, the driver detected a pci error (via pci device state
or via failed register reads) but didn't take any action to disable the
device. Additionally, the driver is ignoring the status of pci
configuration space reads.
Having the driver take the adapter offline whenever the pci error is
detected. Pay attention to pci_config_space_read status and return failure
if an error is seen.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If an adapter fails, causing a board reset, the board reset routine
lpfc_hba_down_s4() takes the hbalock out then calls
lpfc_nvmet_ctxbuf_post() who then tries to take out the same lock. As the
context lists are now protected under the buf_list_locks, there is no need
for the hbalock to be held by the board reset routine.
Fix by no longer taking the hbalock in the board reset routine.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With negative test injection, the driver is receiving a command with first
burst enabled, meaning Sequence initiative is not passed with the command
frame. The driver notes the condition and discards the frame. However the
driver calls the incorrect buffer free routine, resulting in a NULL pointer
reference.
For hbq buffer free, convert to using lpfc_rq_buf_free().
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, when lpfc_nvmet_mrq is 0 it could mean 2 different things
depending on when its looked at. If at module load time it specifies the
default number of hardware queues to allocate, with 0 meaning default to
the number of CPUs. But post module load, a value of zero means to disable
mrq use.
Changed the driver so that enablement of mrq is based on whether nvme
target mode is enabled or not. When enabled, mrq is enabled. Thus, the
cfg_nvemt_mrq field only specifies the number of mrq queues to enable, with
0 defaulting to the number of cpus.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Under circustances with high load, the driver is running out of async
receive buffers which may result in one of the following messages:
0:6401 RQE Error x13, posted 226 err_cnt 0: 925c6050 925c604e 925c5d54
or
0:2885 Port Status Event: port status reg 0x81800000,
port smphr reg 0xc000, error 1=0x52004a01, error 2=0x0
The driver is waiting for full io completion before returning receive
buffers to the adapter. There is no need for such a relationship.
Whenever a new command is received from the wire, the driver will have two
contexts - an io context (ctxp) and a receive buffer context. In current
code, the receive buffer context stays 1:1 with the io and won't be
reposted to the hardware until the io completes. There is no need for such
a relationship.
Change the driver so that up on successful handing of the command to the
transport, where the transport has copied what it needed thus the buffer is
returned to the driver, have the driver immediately repost the buffer to
the hardware. If the command cannot be successfully handed to the transport
as transport resources are temporarily busy, have the driver allocate a new
and separate receive buffer and post it to the hardware so that hardware
can continue while the command is queued for the transport.
When an io is complete, the transport returns the io context to the driver,
and the driver may be waiting for more contexts, thus immediately reuse the
io context. In this path, there was a buffer posted when the receive buffer
was queued waiting for an io context so a replacement is not needed in the
new code additions. Thus, exempt this the context reuse case from the
buffer reposting.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The debug ktime counters that trace an io were inadvertently not placed in
the common section of an io buffer. Thus, they generate an invalid opcode
error when accessed.
Move the ktime counters into the common area.
Fixes: 0794d601d1 ("scsi: lpfc: Implement common IO buffers between NVME and SCSI")
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During debug, it was seen that the driver is issuing commands specific to
SLI3 on SLI4 devices. Although the adapter correctly rejected the command,
this should not be done.
Revise the code to stop sending these commands on a SLI4 adapter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When unloading the driver, mailbox commands may be sent without holding a
reference on the ndlp. By the time the mailbox command completes, the ndlp
may have reduced its ref counts and been freed. The problem was reported
by KASAN.
While unregistering due to driver unload, have the completion noop'd by
setting the ndlp context NULL'd. Due to the unload, no further action was
necessary. Also, while reviewing this path, the generic nulling of the
context after handling should be slightly moved.
Reported by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A patch in the 12.2.0.0 set caused a new lockdep warning:
WARNING: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected
5.0.0-rc8-next-20190301-dbg+ #1 Not tainted
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&(&qp->io_buf_list_put_lock)->rlock);
local_irq_disable();
lock(&(&phba->hbalock)->rlock);
lock(&(&qp->io_buf_list_put_lock)->rlock);
<Interrupt>
lock(&(&phba->hbalock)->rlock);
see: https://www.spinics.net/lists/linux-scsi/msg128389.html
In summary, the new patch added taking the io_buf_list_put_lock while under
an irq-disabled hbalock. This created a lock heirarchy dependent upon irq
being disabled, and there are paths that take the io_buf_list_put_lock
without disabling irq.
Looking at the lpfc_io_free routine, which is where the new heirarchy was
introduced, there is no reason to be taking out the hbalock and raising
irq, as the functionality is replaced by the io_buf_list_xxx locks.
Resolve by removing the hbalock/irq calls in lpfc_io_free.
Fixes: 5e5b511d8b ("scsi: lpfc: Partition XRI buffer list across Hardware Queues")
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A prior patch which added support for non-uniform allocation of MSIX
vectors now causes a smatch complaint:
drivers/scsi/lpfc/lpfc_scsi.c:3674 lpfc_scsi_cmd_iocb_cmpl()
error: we previously assumed 'phba->sli4_hba.hdwq' could be
null (see line 3667)
Resolve by removing the unnecessary check for a NULL hdwq table.
Fixes 6a828b0f6192: ("scsi: lpfc: Support non-uniform allocation of MSIX vectors to hardware queues")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is the final round of mostly small fixes and performance
improvements to our initial submit. The main regression fix is the
ia64 simscsi build failure which was missed in the serial number
elimination conversion.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXIxBayYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pisherpAP4rxLpX
bcUnQnEsvoxys/JyoK08Qfv1JebZo1B2MAZ62wD/VZ7LpOuzVLhsM2KhLFGRrs1/
7D2K4tgtO2dQsFix7H0=
=pcHl
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is the final round of mostly small fixes and performance
improvements to our initial submit.
The main regression fix is the ia64 simscsi build failure which was
missed in the serial number elimination conversion"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
scsi: ia64: simscsi: use request tag instead of serial_number
scsi: aacraid: Fix performance issue on logical drives
scsi: lpfc: Fix error codes in lpfc_sli4_pci_mem_setup()
scsi: libiscsi: Hold back_lock when calling iscsi_complete_task
scsi: hisi_sas: Change SERDES_CFG init value to increase reliability of HiLink
scsi: hisi_sas: Send HARD RESET to clear the previous affiliation of STP target port
scsi: hisi_sas: Set PHY linkrate when disconnected
scsi: hisi_sas: print PHY RX errors count for later revision of v3 hw
scsi: hisi_sas: Fix a timeout race of driver internal and SMP IO
scsi: hisi_sas: Change return variable type in phy_up_v3_hw()
scsi: qla2xxx: check for kstrtol() failure
scsi: lpfc: fix 32-bit format string warning
scsi: lpfc: fix unused variable warning
scsi: target: tcmu: Switch to bitmap_zalloc()
scsi: libiscsi: fall back to sendmsg for slab pages
scsi: qla2xxx: avoid printf format warning
scsi: lpfc: resolve static checker warning in lpfc_sli4_hba_unset
scsi: lpfc: Correct __lpfc_sli_issue_iocb_s4 lockdep check
scsi: ufs: hisi: fix ufs_hba_variant_ops passing
scsi: qla2xxx: Fix panic in qla_dfs_tgt_counters_show
...
It used to be that "error" was set to -ENODEV at the start of the function
but we shifted some code around an now "error" is set to zero for most
error paths. There is a mix of direct returns and "goto out" but I changed
everything to direct returns for consistency.
Fixes: 56de835704 ("scsi: lpfc: fix calls to dma_set_mask_and_coherent()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core. Additionally Christoph
refactored gdth as part of the dma changes. The major mid-layer
change this time is the removal of bidi commands and with them the
whole of the osd/exofs driver and filesystem.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXIC54SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishT1GAPwJEV23
ExPiPsnuVgKj49nLTagZ3rILRQcYNbL+MNYqxQEA0cT8FHzSDBfWY5OKPNE+RQ8z
f69LpXGmMpuagKGvvd4=
=Fhy1
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core.
Additionally Christoph refactored gdth as part of the dma changes. The
major mid-layer change this time is the removal of bidi commands and
with them the whole of the osd/exofs driver and filesystem. This is a
major simplification for block and mq in particular"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (240 commits)
scsi: cxgb4i: validate tcp sequence number only if chip version <= T5
scsi: cxgb4i: get pf number from lldi->pf
scsi: core: replace GFP_ATOMIC with GFP_KERNEL in scsi_scan.c
scsi: mpt3sas: Add missing breaks in switch statements
scsi: aacraid: Fix missing break in switch statement
scsi: kill command serial number
scsi: csiostor: drop serial_number usage
scsi: mvumi: use request tag instead of serial_number
scsi: dpt_i2o: remove serial number usage
scsi: st: osst: Remove negative constant left-shifts
scsi: ufs-bsg: Allow reading descriptors
scsi: ufs: Allow reading descriptor via raw upiu
scsi: ufs-bsg: Change the calling convention for write descriptor
scsi: ufs: Remove unused device quirks
Revert "scsi: ufs: disable vccq if it's not needed by UFS device"
scsi: megaraid_sas: Remove a bunch of set but not used variables
scsi: clean obsolete return values of eh_timed_out
scsi: sd: Optimal I/O size should be a multiple of physical block size
scsi: MAINTAINERS: SCSI initiator and target tweaks
scsi: fcoe: make use of fip_mode enum complete
...
On 32-bit architectures, we see a warning when %ld is used to print a
size_t:
In file included from drivers/scsi/lpfc/lpfc_init.c:62:
drivers/scsi/lpfc/lpfc_init.c: In function 'lpfc_new_io_buf':
drivers/scsi/lpfc/lpfc_logmsg.h:62:45: error: format '%ld' expects argument of type 'long int', but argument 5 has type 'unsigned int' [-Werror=format=]
This is harmless, but portable code should just use %zd to avoid the
warning.
Fixes: 0794d601d1 ("scsi: lpfc: Implement common IO buffers between NVME and SCSI")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The newly introduced 'cpu' variable is only used inside of an optional
block, so we get a warning without CONFIG_SCSI_LPFC_DEBUG_FS:
drivers/scsi/lpfc/lpfc_nvme.c: In function 'lpfc_nvme_io_cmd_wqe_cmpl':
drivers/scsi/lpfc/lpfc_nvme.c:968:30: error: unused variable 'cpu' [-Werror=unused-variable]
uint32_t code, status, idx, cpu;
Move the declaration into the same block to avoid the warning.
Fixes: 63df6d637e ("scsi: lpfc: Adapt cpucheck debugfs logic to Hardware Queues")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The patch that replaced io channels for hdw_queues now reports the
following static checker warning:
drivers/scsi/lpfc/lpfc_init.c:11136 lpfc_sli4_hba_unset()
error: we previously assumed 'phba->pport' could be null (see line 11074)
Resolve by adding a pport NULL check.
[mkp: tag tweak]
Fixes: cdb42becdd ("scsi: lpfc: Replace io_channels for nvme and fcp with general hdw_queues per cpu"_
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The outer routine lpfc_sli_issue_iocb(), which decomposes into the
SLI3 (s3) or SLI4 (s4) subroutines takes out the locks. For s3, it takes
out the hbalock. For s4, it takes out the ring_lock. The lockdep check in
the s3 and s4 subroutines both check hbalock, which is incorrect for s4.
Revise the s4 subroutine to lockdep check the ring_lock.
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Nine small fixes. The resume fix is a cosmetic removal of a warning
with an incorrect condition causing it to alarm people wrongly. The
other eight patches correct a thinko in Christoph Hellwig's DMA
conversion series. Without it all these drivers end up with 32 bit
DMA masks meaning they bounce any page over 4GB before sending it to
the controller. Nowadays, even laptops mostly have memory above 4GB,
so this can lead to significant performance degradation with all the
bouncing.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXHql8CYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishQmvAQCSVQRf
kx3ABDGnaj4Km4/Jzibj44aCYwh+ewwtLCWwFQD9GWaEaDxBkbxQDf/YndQKRhYg
VJQjjj6a9VlNSmWoW28=
=L9Fe
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Nine small fixes.
The resume fix is a cosmetic removal of a warning with an incorrect
condition causing it to alarm people wrongly.
The other eight patches correct a thinko in Christoph Hellwig's DMA
conversion series. Without it all these drivers end up with 32 bit DMA
masks meaning they bounce any page over 4GB before sending it to the
controller.
Nowadays, even laptops mostly have memory above 4GB, so this can lead
to significant performance degradation with all the bouncing"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: core: Avoid that system resume triggers a kernel warning
scsi: hptiop: fix calls to dma_set_mask()
scsi: hisi_sas: fix calls to dma_set_mask_and_coherent()
scsi: csiostor: fix calls to dma_set_mask_and_coherent()
scsi: bfa: fix calls to dma_set_mask_and_coherent()
scsi: aic94xx: fix calls to dma_set_mask_and_coherent()
scsi: 3w-sas: fix calls to dma_set_mask_and_coherent()
scsi: 3w-9xxx: fix calls to dma_set_mask_and_coherent()
scsi: lpfc: fix calls to dma_set_mask_and_coherent()
The change to use dma_set_mask_and_coherent() incorrectly made a second
call with the 32 bit DMA mask value when the call with the 64 bit DMA mask
value succeeded. This resulted in NVMe/FC connections failing due to
corrupted data buffers, and various other SCSI/FCP I/O errors.
Fixes: f30e1bfd61 ("scsi: lpfc: use dma_set_mask_and_coherent")
Cc: <stable@vger.kernel.org>
Suggested-by: Don Dutile <ddutile@redhat.com>
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/lpfc/lpfc_init.c: In function 'lpfc_cpu_affinity_check':
drivers/scsi/lpfc/lpfc_init.c:10599:19: warning:
variable 'phys_id' set but not used [-Wunused-but-set-variable]
It never used since introduction in commit 6a828b0f61 ("scsi: lpfc:
Support non-uniform allocation of MSIX vectors to hardware queues")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are a handful of statements that are indented incorrectly. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This should return -ENOMEM if kcalloc() fails, but it accidentally
returns success instead.
Fixes: 6a828b0f61 ("scsi: lpfc: Support non-uniform allocation of MSIX vectors to hardware queues")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.2.0.0
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For files modified as part of 12.2.0.0 patches, update copyright to 2019
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Various null pointer dereference and general protection fault panics occur
when there is a link bounce under load. There are a large number of "error"
message 6413 indicating "bad release".
The issues resolve to list corruptions due to missing or inconsistent lock
protection. Lockups are due to nested locks in the unsolicited abort
path. The unsolicited abort path calls the wrong abort processing
routine. There was also duplicate context release while aborts were still
active in the hardware.
Removed duplicate locks and added lock protection around list item
removal. Commonized lock handling around the abort processing routines.
Prevent context release while still in ABTS list.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart