Previously the green and amber LEDs on this quad PHY were solid, to
indicate an encoding of the link speed (10/100/1000).
This keeps the LEDs always on just as before, but now they flash on
Rx/Tx activity.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far we effectively clear the BMCR register. Some PHY's can deal
with this (e.g. because they reset BMCR to a default as part of a
soft-reset) whilst on others this causes issues because e.g. the
autoneg bit is cleared. Marvell is an example, see also thread [0].
So let's be a little bit more gentle and leave all bits we're not
interested in as-is. This change is needed for PHY drivers to
properly deal with the original patch.
[0] https://marc.info/?t=155264050700001&r=1&w=2
Fixes: 6e2d85ec05 ("net: phy: Stop with excessive soft reset")
Tested-by: Phil Reid <preid@electromag.com.au>
Tested-by: liweihang <liweihang@hisilicon.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After 90eff9096c ("net: phy: Allow splitting MDIO bus/device support
from PHYs") the various MDIO bus drivers were no longer parented with
config PHYLIB but with config MDIO_BUS which is not a menuconfig, fix
this by depending on MDIO_DEVICE which is a menuconfig.
This is visually nicer and less confusing for users.
Fixes: 90eff9096c ("net: phy: Allow splitting MDIO bus/device support from PHYs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the DP83825I ethernet PHY to the DP83822 driver.
These devices share the same WoL register bits and addresses.
The phy_driver init was made into a macro as there may be future
devices appended to this driver that will share the register space.
http://www.ti.com/lit/gpn/dp83825i
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an interrupt is already pending when the interrupt is enabled on the
GXL phy, no IRQ will ever be triggered.
The fix is simply to make sure pending IRQs are cleared before setting
up the irq mask.
Fixes: cf127ff20a ("net: phy: meson-gxl: add interrupt support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO_BUS_MUX can only be selected if OF_MDIO is already turned on:
WARNING: unmet direct dependencies detected for MDIO_BUS_MUX
Depends on [n]: NETDEVICES [=y] && MDIO_BUS [=m] && OF_MDIO [=n]
Selected by [m]:
- MDIO_BUS_MUX_MULTIPLEXER [=m] && NETDEVICES [=y] && MDIO_BUS [=m] && OF [=y]
Fixes: 7865ad6551 ("drivers: net: phy: mdio-mux: Add support for Generic Mux controls")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
As can be seen from the usage of the return value, we should use
phy_modify_mmd_changed() here.
Fixes: 9a5dc8af44 ("net: phy: add genphy_c45_an_config_aneg")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
genphy_no_soft_reset and gen10g_no_soft_reset are both the same no-ops,
one is enough.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
gen10g_read_status is deprecated, therefore stop exporting it.
We don't want to encourage anybody to use it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
ETHTOOL_LINK_MODE_10000baseT_Full_BIT is set anyway in the supported
and advertising bitmap because it's part of PHY_10GBIT_FEATURES.
And all users of gen10g_config_init use PHY_10GBIT_FEATURES.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_suspend() and phy_resume() are no-ops anyway if no callback is
defined. Therefore we don't need these stubs.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have it let's use genphy_c45_aneg_done() in phy_aneg_done().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When debugging an issue I found implausible values in state->pause.
Reason in that state->pause isn't initialized and later only single
bits are changed. Also the struct itself isn't initialized in
phylink_resolve(). So better initialize state->pause and other
not yet initialized fields.
v2:
- use right function name in subject
v3:
- initialize additional fields
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Contrary to the 3310, the 2110 PHY correctly reports it's 2.5G/5G
abilities. We can therefore use the genphy_c45_pma_read_abilities helper
to build the list of features.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The genphy_c45_pma_read_abilities helper now sets the Autoneg ability
in phydev->supported according to what the AN MMD reports.
We therefore don't need to manually do that in mv3310_get_features().
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to dp83640 delay after soft reset
is needed to set up registers correctly.
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for Generic Mux controls, when Mdio mux node is a consumer
of mux produced by some other device.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With Micrel KSZ8061 PHY, the link may occasionally not come up after
Ethernet cable connect. The vendor's (Microchip, former Micrel) errata
sheet 80000688A.pdf descripes the problem and possible workarounds in
detail, see below.
The batch implements workaround 1, which permanently fixes the issue.
DESCRIPTION
Link-up may not occur properly when the Ethernet cable is initially
connected. This issue occurs more commonly when the cable is connected
slowly, but it may occur any time a cable is connected. This issue occurs
in the auto-negotiation circuit, and will not occur if auto-negotiation
is disabled (which requires that the two link partners be set to the
same speed and duplex).
END USER IMPLICATIONS
When this issue occurs, link is not established. Subsequent cable
plug/unplaug cycle will not correct the issue.
WORk AROUND
There are four approaches to work around this issue:
1. This issue can be prevented by setting bit 15 in MMD device address 1,
register 2, prior to connecting the cable or prior to setting the
Restart Auto-negotiation bit in register 0h. The MMD registers are
accessed via the indirect access registers Dh and Eh, or via the Micrel
EthUtil utility as shown here:
. if using the EthUtil utility (usually with a Micrel KSZ8061
Evaluation Board), type the following commands:
> address 1
> mmd 1
> iw 2 b61a
. Alternatively, write the following registers to write to the
indirect MMD register:
Write register Dh, data 0001h
Write register Eh, data 0002h
Write register Dh, data 4001h
Write register Eh, data B61Ah
2. The issue can be avoided by disabling auto-negotiation in the KSZ8061,
either by the strapping option, or by clearing bit 12 in register 0h.
Care must be taken to ensure that the KSZ8061 and the link partner
will link with the same speed and duplex. Note that the KSZ8061
defaults to full-duplex when auto-negotiation is off, but other
devices may default to half-duplex in the event of failed
auto-negotiation.
3. The issue can be avoided by connecting the cable prior to powering-up
or resetting the KSZ8061, and leaving it plugged in thereafter.
4. If the above measures are not taken and the problem occurs, link can
be recovered by setting the Restart Auto-Negotiation bit in
register 0h, or by resetting or power cycling the device. Reset may
be either hardware reset or software reset (register 0h, bit 15).
PLAN
This errata will not be corrected in the future revision.
Fixes: 7ab59dc15e ("drivers/net/phy/micrel_phy: Add support for new PHYs")
Signed-off-by: Alexander Onnasch <alexander.onnasch@landisgyr.com>
Signed-off-by: Rajasingh Thavamani <T.Rajasingh@landisgyr.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds HWMON support for the temperature sensor and the related
alarms on the 107/108/109 chips. This patch is based on work from
Nikita and Andrew. I added:
- support for changing alarm thresholds via sysfs
- move HWMON code to a separate source file to improve maintainability
- smaller changes like using IS_REACHABLE instead of ifdef
(avoids problems if PHY driver is built in and HWMON is a module)
v2:
- remove struct aqr_priv
- rename header file to aquantia.h
v3:
- add conditional compiling of aquantia_hwmon.c
- improve converting sensor register values to/from long
- add helper aqr_hwmon_test_bit
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename aquantia.c to aquantia_main.c to be prepared for adding new
functionality to separate source code files.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the switch to phy_resolve_aneg_linkmode() we don't read from the
chip any longer what is advertised but use phydev->advertising directly.
For a fixed phy however this bitmap is empty so far, what results in
no common mode being found. This breaks DSA. Fix this by advertising
everything that is supported. For a normal phy this done by phy_probe().
Fixes: 5502b218e0 ("net: phy: use phy_resolve_aneg_linkmode in genphy_read_status")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Auto-neg emulation currently doesn't set bit BMCR_ANENABLE in BMCR,
add this. Users will ignore speed and duplex settings in BMCR because
we're emulating auto-neg, therefore we can remove related code.
See also following discussion [0].
[0] https://marc.info/?t=155041784900002&r=1&w=2
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the 88x2110 PHY, which is similar to the
already supported 88x3310 PHY without the SFP interface.
It supports 10/100/1000BASET along with 2.5GBASET, 5GBASET and 10GBASET,
with the same interface modes that are used by the 3310.
This PHY don't have the same issue as the 88x3310 regarding 2.5/5G
abilities, and correctly follows the 802.3bz standard to list the
supported abilities.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Suggested-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per 802.3bz, if bit 14 of (1.11) "PMA Extended Abilities" indicates
whether or not we should read register (1.21) "2.52/5G PMA Extended
Abilities", which contains information on the support of 2.5GBASET and
5GBASET.
After testing on several variants of PHYS of this family, it appears
that bit 14 in (1.11) isn't always set when it should be.
PHYs 88X3310 (on MacchiatoBin) and 88E2010 do support 2.5G and 5GBASET,
but don't have 1.11.14 set. Their register 1.21 is filled with the
correct values, indicating 2.5G and 5G support.
PHYs 88E2110 do have their 1.11.14 bit set, as it should.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY ID corresponding to the 88X3310 is also used for other PHYs in
the same family, such as the 88E2010. Use a #define for the PHY id, that
ignores the last nibble.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell Alaska family of PHYs supports 2.5GBaseT and 5GBaseT modes,
as defined in the 802.3bz specification.
Upon establishing a 2.5GBASET link, the PHY will reconfigure it's MII
interface to 2500BASEX.
At 5G, the PHY will reconfigure it's interface to 5GBASE-R, but this
mode isn't supported by any MAC for now.
This was tested with :
- The 88X3310, which is on the MacchiatoBin
- The 88E2010, an Alaska PHY that has no fiber interfaces, and is
limited to 5G maximum speed.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic patch making use of helpers dedicated to linkmodes handling.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Alaska family of 10G PHYs has more abilities than the ones listed in
PHY_10GBIT_FULL_FEATURES, the exact list depending on the model.
Make use of the newly introduced .get_features call to build this list,
using genphy_c45_pma_read_abilities to build the list of supported
linkmodes, and adding autoneg ability based on what's reported by the AN
MMD.
.config_init is still used to validate the interface_mode.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code reports a link as up if all devices (except a few
blacklisted ones) report the link as up. This breaks Aquantia AQCS109
for lower speeds because on this PHY the PCS link status reflects a
10G link only. For Marvell there's a similar issue, therefore PHYXS
device isn't checked.
There may be more PHYs where depending on the mode the link status
of only selected devices is relevant.
For now it seems to be sufficient to check the link status of the
PMAPMD device only. Leave the loop in the code to be prepared in
case we have to add functionality to check more than one device,
depending on the mode.
Successfully tested on a board with an AQCS109.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using genphy_c45_read_abilities() as get_features callback we
also have to set the autoneg capability in phydev->supported.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three conflicts, one of which, for marvell10g.c is non-trivial and
requires some follow-up from Heiner or someone else.
The issue is that Heiner converted the marvell10g driver over to
use the generic c45 code as much as possible.
However, in 'net' a bug fix appeared which makes sure that a new
local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0
is cleared.
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a regression introduced by
commit 0d2e778e38
"net: phy: replace PHY_HAS_INTERRUPT with a check for
config_intr and ack_interrupt".
This assumes that a PHY cannot trigger interrupt unless
it has .config_intr() or .ack_interrupt() implemented.
A later patch makes the code assume both need to be
implemented for interrupts to be present.
But this PHY (which is inside a DSA) will happily
fire interrupts without either callback.
Implement dummy callbacks for .config_intr() and
.ack_interrupt() in the phy header to fix this.
Tested on the RTL8366RB on D-Link DIR-685.
Fixes: 0d2e778e38 ("net: phy: replace PHY_HAS_INTERRUPT with a check for config_intr and ack_interrupt")
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new function genphy_c45_read_status(). 1000BaseT link partner
advertisement needs to be read from vendor registers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to genphy_read_status() for Clause 22 add a generic read_status
function for Clause 45.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because 1000BaseT isn't covered by Clause 45, the 1000BaseT flags in
phydev->lp_advertising may have been set based on vendor registers
already. genphy_c45_read_lpa() would clear these flags as of today.
Therefore switch to mii_lpa_mod_linkmode_lpa_t.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the generic c45 code, plus code specific to the Aquantia
phy for 1000BaseT negotiation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AQCS109 belongs to a family of PHY's where certain members don't
support 5G or 10G. However for all members of the family the chip
reports 10G and 5G capability. Therefore remove the not supported
modes for AQCS109.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Marvell Alaska PHYs support 2.5G, 5G and 10G BaseT links. Their
default behaviour is to advertise all of these modes, but at the moment,
only 10GBaseT is supported. To prevent link partners from establishing
link at that speed, clear these modes upon configuring aneg parameters.
Fixes: 20b2af32ff ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reported-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per "Documentation/devicetree/bindings/net/ethernet.txt" RGMII mode
should not have delay in PHY whereas RGMII_ID and RGMII_RXID/RGMII_TXID
can have delay in PHY.
So disable the delay only for RGMII mode and enable for other modes.
Also treat the default case as disabled delays.
Fixes: cd28d1d6e52e: ("net: phy: at803x: Disable phy delay for RGMII mode")
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Tested-by: Peter Ujfalusi <peter.ujflausi@ti.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some helpers were declared with the "inline" function specifier.
It is preferable to let the compiler pick the right optimizations,
so drop the specifier for at803x_disable_rx_delay() and
at803x_disable_tx_delay()
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Tested-by: Peter Ujfalusi <peter.ujflausi@ti.com>
Reviewed-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new PHY driver call to get the PHYs supported features.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[hkallweit1@gmail.com: removed new config_init callback from patch]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new function genphy_c45_check_and_restart_aneg() to reduce
boilerplate code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function will be used by config_aneg callback implementations of
PHY drivers and allows to reduce boilerplate code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like in genphy_config_aneg() for clause 22 PHY's, we should keep modes
from being advertised that are known to be broken with EEE.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to use this function in phy-c45.c too, therefore export it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If link partner and we can't agree on any mode, then it doesn't make
sense to pretend we would have agreed on 10/half. Therefore set a
proper default.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After recent changes to genphy_read_status() this orphaned register
read remained as leftover. So remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that genphy_c45_pma_setup_forced() makes sure the "aneg enabled"
bit is cleared, the call to genphy_c45_an_disable_aneg() isn't needed
any longer. And the code pattern is now the same as in
genphy_config_aneg().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean