Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
Scenario:
* Multicast frame send from mesh to a BLA backbone (multiple nodes
with their bat0 bridged together, with BLA enabled)
Issue:
* BLA backbone nodes receive the frame multiple times on bat0,
once from mesh->bat0 and once from each backbone_gw from LAN
For unicast, a node will send only to the best backbone gateway
according to the TQ. However for multicast we currently cannot determine
if multiple destination nodes share the same backbone if they don't share
the same backbone with us. So we need to keep sending the unicasts to
all backbone gateways and let the backbone gateways decide which one
will forward the frame. We can use the CLAIM mechanism to make this
decision.
One catch: The batman-adv gateway feature for DHCP packets potentially
sends multicast packets in the same batman-adv unicast header as the
multicast optimizations code. And we are not allowed to drop those even
if we did not claim the source address of the sender, as for such
packets there is only this one multicast-in-unicast packet.
How can we distinguish the two cases?
The gateway feature uses a batman-adv unicast 4 address header. While
the multicast-to-unicasts feature uses a simple, 3 address batman-adv
unicast header. So let's use this to distinguish.
Fixes: fe2da6ff27 ("batman-adv: check incoming packet type for bla")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Scenario:
* Multicast frame send from a BLA backbone (multiple nodes with
their bat0 bridged together, with BLA enabled)
Issue:
* BLA backbone nodes receive the frame multiple times on bat0
For multicast frames received via batman-adv broadcast packets the
originator of the broadcast packet is checked before decapsulating and
forwarding the frame to bat0 (batadv_bla_is_backbone_gw()->
batadv_recv_bcast_packet()). If it came from a node which shares the
same BLA backbone with us then it is not forwarded to bat0 to avoid a
loop.
When sending a multicast frame in a non-4-address batman-adv unicast
packet we are currently missing this check - and cannot do so because
the batman-adv unicast packet has no originator address field.
However, we can simply fix this on the sender side by only sending the
multicast frame via unicasts to interested nodes which do not share the
same BLA backbone with us. This also nicely avoids some unnecessary
transmissions on mesh side.
Note that no infinite loop was observed, probably because of dropping
via batadv_interface_tx()->batadv_bla_tx(). However the duplicates still
utterly confuse switches/bridges, ICMPv6 duplicate address detection and
neighbor discovery and therefore leads to long delays before being able
to establish TCP connections, for instance. And it also leads to the Linux
bridge printing messages like:
"br-lan: received packet on eth1 with own address as source address ..."
Fixes: 2d3f6ccc4e ("batman-adv: Modified forwarding behaviour for multicast packets")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
checkpatch found various instances of "Possible repeated word" in various
comments.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The dynamic key update for addr_list_lock still causes troubles,
for example the following race condition still exists:
CPU 0: CPU 1:
(RCU read lock) (RTNL lock)
dev_mc_seq_show() netdev_update_lockdep_key()
-> lockdep_unregister_key()
-> netif_addr_lock_bh()
because lockdep doesn't provide an API to update it atomically.
Therefore, we have to move it back to static keys and use subclass
for nest locking like before.
In commit 1a33e10e4a ("net: partially revert dynamic lockdep key
changes"), I already reverted most parts of commit ab92d68fc2
("net: core: add generic lockdep keys").
This patch reverts the rest and also part of commit f3b0a18bb6
("net: remove unnecessary variables and callback"). After this
patch, addr_list_lock changes back to using static keys and
subclasses to satisfy lockdep. Thanks to dev->lower_level, we do
not have to change back to ->ndo_get_lock_subclass().
And hopefully this reduces some syzbot lockdep noises too.
Reported-by: syzbot+f3a0e80c34b3fc28ac5e@syzkaller.appspotmail.com
Cc: Taehee Yoo <ap420073@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 1a33e10e4a ("net: partially revert dynamic lockdep key
changes") reverts the commit ab92d68fc2 ("net: core: add generic lockdep
keys"). But it forgot to also revert the commit 5759af0682 ("batman-adv:
Drop lockdep.h include for soft-interface.c") which depends on the latter.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
This patch reverts the folowing commits:
commit 064ff66e2b
"bonding: add missing netdev_update_lockdep_key()"
commit 53d374979e
"net: avoid updating qdisc_xmit_lock_key in netdev_update_lockdep_key()"
commit 1f26c0d3d2
"net: fix kernel-doc warning in <linux/netdevice.h>"
commit ab92d68fc2
"net: core: add generic lockdep keys"
but keeps the addr_list_lock_key because we still lock
addr_list_lock nestedly on stack devices, unlikely xmit_lock
this is safe because we don't take addr_list_lock on any fast
path.
Reported-and-tested-by: syzbot+aaa6fa4949cc5d9b7b25@syzkaller.appspotmail.com
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit ab92d68fc2 ("net: core: add generic lockdep keys") removed
all lockdep functionality from soft-interface.c but didn't remove the
include for this functionality.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The usage of the '/* fall through */' comments in switches are no longer
marked as non-deprecated variant of implicit fall throughs for switch
statements. The commit 294f69e662 ("compiler_attributes.h: Add
'fallthrough' pseudo keyword for switch/case use") introduced a replacement
keyword which should be used instead.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Some interface types could be nested.
(VLAN, BONDING, TEAM, MACSEC, MACVLAN, IPVLAN, VIRT_WIFI, VXLAN, etc..)
These interface types should set lockdep class because, without lockdep
class key, lockdep always warn about unexisting circular locking.
In the current code, these interfaces have their own lockdep class keys and
these manage itself. So that there are so many duplicate code around the
/driver/net and /net/.
This patch adds new generic lockdep keys and some helper functions for it.
This patch does below changes.
a) Add lockdep class keys in struct net_device
- qdisc_running, xmit, addr_list, qdisc_busylock
- these keys are used as dynamic lockdep key.
b) When net_device is being allocated, lockdep keys are registered.
- alloc_netdev_mqs()
c) When net_device is being free'd llockdep keys are unregistered.
- free_netdev()
d) Add generic lockdep key helper function
- netdev_register_lockdep_key()
- netdev_unregister_lockdep_key()
- netdev_update_lockdep_key()
e) Remove unnecessary generic lockdep macro and functions
f) Remove unnecessary lockdep code of each interfaces.
After this patch, each interface modules don't need to maintain
their lockdep keys.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 174e23810c
("sk_buff: drop all skb extensions on free and skb scrubbing") made napi
recycle always drop skb extensions. The additional skb_ext_del() that is
performed via nf_reset on napi skb recycle is not needed anymore.
Most nf_reset() calls in the stack are there so queued skb won't block
'rmmod nf_conntrack' indefinitely.
This removes the skb_ext_del from nf_reset, and renames it to a more
fitting nf_reset_ct().
In a few selected places, add a call to skb_ext_reset to make sure that
no active extensions remain.
I am submitting this for "net", because we're still early in the release
cycle. The patch applies to net-next too, but I think the rename causes
needless divergence between those trees.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The strscpy was introduced to fix some API problems around strlcpy. And
checkpatch started to report recently that strlcpy is deprecated and
strscpy is preferred.
The functionality introduced in commit 30035e4575 ("string: provide
strscpy()") improves following points compared to strlcpy:
* it doesn't read from memory beyond (src + size)
* provides an easy way to check for destination buffer overflow
* robust against asynchronous source buffer changes
Since batman-adv doesn't depend on any of the previously mentioned behavior
changes, the usage of strlcpy can simply be replaced by strscpy to silence
checkpatch.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
It is not necessary to hold the mla_lock spinlock during the whole
multicast tt/tvlv worker callback. Just holding it during the checks and
updates of the bat_priv stored multicast flags and mla_list is enough.
Therefore this patch splits batadv_mcast_mla_tvlv_update() in two:
batadv_mcast_mla_flags_get() at the beginning of the worker to gather
and calculate the new multicast flags, which does not need any locking
as it neither reads from nor writes to bat_priv->mcast.
And batadv_mcast_mla_flags_update() at the end of the worker which
commits the newly calculated flags and lists to bat_priv->mcast and
therefore needs the lock.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
While it can be slightly beneficial for the build performance to use
forward declarations instead of includes, the handling of them together
with changes in the included headers makes it unnecessary complicated and
fragile. Just replace them with actual includes since some parts (hwmon,
..) of the kernel even request avoidance of forward declarations and net/
is mostly not using them in *.c file.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
With this patch multicast packets with a limited number of destinations
(current default: 16) will be split and transmitted by the originator as
individual unicast transmissions.
Wifi broadcasts with their low bitrate are still a costly undertaking.
In a mesh network this cost multiplies with the overall size of the mesh
network. Therefore using multiple unicast transmissions instead of
broadcast flooding is almost always less burdensome for the mesh
network.
The maximum amount of unicast packets can be configured via the newly
introduced multicast_fanout parameter. If this limit is exceeded
distribution will fall back to classic broadcast flooding.
The multicast-to-unicast conversion is performed on the initial
multicast sender node and counts on a final destination node, mesh-wide
basis (and not next hop, neighbor node basis).
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
All files got a SPDX-License-Identifier with commit 7db7d9f369
("batman-adv: Add SPDX license identifier above copyright header"). All the
required information about the license conditions can be found in
LICENSES/.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The netfilter conflicts were rather simple overlapping
changes.
However, the cls_tcindex.c stuff was a bit more complex.
On the 'net' side, Cong is fixing several races and memory
leaks. Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.
What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU. I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
- fix memory leak in in batadv_dat_put_dhcp, by Martin Weinelt
- fix typo, by Sven Eckelmann
- netlink restructuring patch series (part 2), by Sven Eckelmann
(19 patches)
-----BEGIN PGP SIGNATURE-----
iQJKBAABCgA0FiEE1ilQI7G+y+fdhnrfoSvjmEKSnqEFAlxj6MYWHHN3QHNpbW9u
d3VuZGVybGljaC5kZQAKCRChK+OYQpKeoYTMD/9Uyaqe4ULGQ+rLBnCMSuNc5AnQ
d7hebUep1RVDyyzJaHRNLmPwmSDNscdQX2AaAxOMhrbmDiBceHq1vDpNvLMDCa0g
4KbljpfICc6Wm8cq6zHMvL5DQYdxvHt3xDDOvTufhTDra0+cZ8b7tLN1GIztrSSL
BJ4gUkVydtFUIGCPkSfqZoMI82VTo4V/vOQpaAAANJXVehajHhPLOc2+AqnsHTxC
6EpNFbMib7sxvrDV5/GdkhtyikmNyHXlaZaiboJjH8htdRWmxHSIfelgDZ2KzqJK
NG5EhZNljLEHHU5cnCBA1ptvjB0zWVF1WEZDyD3fHPraNdmeyCyqI1kuEMFHPSEr
PZ+gD9wqnmgQUc3D7Xi7Q0faEQ5wcOKtcCvMrWgydbQxanhiftBH8pikkR9VJh+B
1ADuN2m+OSKaZ8Fw5tqknNbd8paKztlndgSNRHEc9KOWnT91cKO02Zg9wCyNhn7S
SI/0eLZx0N0v3T/UVsoKbjKGCEiFZzgXMBRRb7jthJghD2hnyx+s1tRzkgxIJj8z
fI5hwAl//m6tSCDjbOLjCdsNHiGs4AhP0MsFq5jHmpqvsY8ZUX59LcRnpfhX3IaN
L+KpBxH9O25Pd3JgXgjlcuza2L1L/V7piPUit/C8LVb7goNN3QCi+UtXFVMR1C4c
J7kI7vMak8BEIs4EuQ==
=+p14
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20190213' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature/cleanup patchset includes the following patches:
- fix memory leak in in batadv_dat_put_dhcp, by Martin Weinelt
- fix typo, by Sven Eckelmann
- netlink restructuring patch series (part 2), by Sven Eckelmann
(19 patches)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The mesh/soft-interface can optimize the handling of DHCP packets. Instead
of flooding them through the whole mesh, it can be forwarded as unicast to
a specific gateway server. The originator which injects the packets in the
mesh has to select (based on sel_class thresholds) a responsible gateway
server. This is done by switching this originator to the gw_mode client.
The servers announce their forwarding bandwidth (download/upload) when the
gw_mode server was selected.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the attributes:
* u8 BATADV_ATTR_GW_MODE (0 == off, 1 == client, 2 == server)
* u32 BATADV_ATTR_GW_BANDWIDTH_DOWN (in 100 kbit/s steps)
* u32 BATADV_ATTR_GW_BANDWIDTH_UP (in 100 kbit/s steps)
* u32 BATADV_ATTR_GW_SEL_CLASS
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
An ipvlan bug fix in 'net' conflicted with the abstraction away
of the IPV6 specific support in 'net-next'.
Similarly, a bug fix for mlx5 in 'net' conflicted with the flow
action conversion in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The caller of ndo_start_xmit may not already have called
skb_reset_mac_header. The returned value of skb_mac_header/eth_hdr
therefore can be in the wrong position and even outside the current skbuff.
This for example happens when the user binds to the device using a
PF_PACKET-SOCK_RAW with enabled qdisc-bypass:
int opt = 4;
setsockopt(sock, SOL_PACKET, PACKET_QDISC_BYPASS, &opt, sizeof(opt));
Since eth_hdr is used all over the codebase, the batadv_interface_tx
function must always take care of resetting it.
Fixes: c6c8fea297 ("net: Add batman-adv meshing protocol")
Reported-by: syzbot+9d7405c7faa390e60b4e@syzkaller.appspotmail.com
Reported-by: syzbot+7d20bc3f1ddddc0f9079@syzkaller.appspotmail.com
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
In a 1000 nodes mesh network (Freifunk Hamburg) we can still see
30KBit/s of ARP traffic (equalling about 25% of all layer two
specific overhead, remaining after some filtering) flooded through
the mesh. These 30KBit/s are mainly ARP Requests from the
gateways / DHCP servers.
By snooping DHCPACKs we can learn about MAC/IP address pairs
in the DHCP range without relying on ARP. This patch is in preparation
to eliminate the need for mesh wide message flooding for IPv4 address
resolution.
Also this allows to quickly update a MAC/IP pair at least in the DHT when
DHCP reassigns an IP address to a new host.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Version bump conflict in batman-adv, take what's in net-next.
iavf conflict, adjustment of netdev_ops in net-next conflicting
with poll controller method removal in net.
Signed-off-by: David S. Miller <davem@davemloft.net>
The batadv interfaces are virtual interfaces which just tunnel the traffic
over other ethernet compatible interfaces. It doesn't need serialization
during the tx phase and is using RCU for most of its internal
datastructures. Since it doesn't have actual queues which could be locked
independently, the throughput gets significantly reduced by the extra lock
in the core net code.
8 parallel TCP connections forwarded by an IPQ4019 based hardware over
5GHz could reach:
* without LLTX: 349 Mibit/s
* with LLTX: 563 Mibit/s
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
B.A.T.M.A.N. IV requires the number of rebroadcast from a neighboring
originator. These statistics are gathered per interface which transmitted
the OGM (and then received it again). Since an originator is not interface
specific, a resizable array was used in each originator.
This resizable array had an entry for each interface and had to be resizes
(for all OGMs) when the number of active interface was modified. This could
cause problems when a large number of interface is added and not enough
continuous memory is available to allocate the array.
There is already a per interface originator structure "batadv_orig_ifinfo"
which can be used to store this information.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The function batadv_softif_vlan_get is responsible for adding new
softif_vlan to the softif_vlan_list. It first checks whether the entry
already is in the list or not. If it is, then the creation of a new entry
is aborted.
But the lock for the list is only held when the list is really modified.
This could lead to duplicated entries because another context could create
an entry with the same key between the check and the list manipulation.
The check and the manipulation of the list must therefore be in the same
locked code section.
Fixes: 5d2c05b213 ("batman-adv: add per VLAN interface attribute framework")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
[sven@narfation.org: fixed alignment]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Instead of disabling multicast optimizations mesh-wide once a node with
no multicast optimizations capabilities joins the mesh, do the
following:
Just insert such nodes into the WANT_ALL_IPV4/IPV6 lists. This is
sufficient to avoid multicast packet loss to such unsupportive nodes.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
All of the conflicts were cases of overlapping changes.
In net/core/devlink.c, we have to make care that the
resouce size_params have become a struct member rather
than a pointer to such an object.
Signed-off-by: David S. Miller <davem@davemloft.net>
eth_type_trans() internally calls skb_pull(), which does not adjust the
skb checksum; skb_postpull_rcsum() is necessary to avoid log spam of the
form "bat0: hw csum failure" when packets with CHECKSUM_COMPLETE are
received.
Note that in usual setups, packets don't reach batman-adv with
CHECKSUM_COMPLETE (I assume NICs bail out of checksumming when they see
batadv's ethtype?), which is why the log messages do not occur on every
system using batman-adv. I could reproduce this issue by stacking
batman-adv on top of a VXLAN interface.
Fixes: c6c8fea297 ("net: Add batman-adv meshing protocol")
Tested-by: Maximilian Wilhelm <max@sdn.clinic>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The header file is used by different userspace programs to inject packets
or to decode sniffed packets. It should therefore be available to them as
userspace header.
Also other components in the kernel (like the flow dissector) require
access to the packet definitions to be able to decode ETH_P_BATMAN ethernet
packets.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the kernel-doc documentation, externally visible functions
should be documented. This refers to all all non-static function which can
(and will) be used by functions in other sources files.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The documentation describing kernel-doc comments for functions ("How to
format kernel-doc comments") uses parentheses at the end of the function
name. Using this format allows to use a consistent style when adding
documentation to a function and when referencing this function in a
different kernel-doc section.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The linux/gfp.h provides the GFP_ATOMIC and GFP_KERNEL define. It should
therefore be included instead of linux/fs.h.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The "Linux kernel licensing rules" require that each file has a SPDX
license identifier as first line (and sometimes as second line).
The FSFE REUSE practices [1] would also require the same tags but have no
restrictions on the placement in the source file. Using the "Linux kernel
licensing rules" is therefore also fulfilling the FSFE REUSE practices
requirements at the same time.
[1] https://reuse.software/practices/
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The parameter extack was added to batadv_softif_slave_add without adding
the kernel-doc for it. This caused kernel-doc warnings.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
- bump version strings, by Simon Wunderlich
- Cleanup patches to make checkpatch happy, by Sven Eckelmann (3 patches)
-----BEGIN PGP SIGNATURE-----
iQJKBAABCgA0FiEE1ilQI7G+y+fdhnrfoSvjmEKSnqEFAlnXingWHHN3QHNpbW9u
d3VuZGVybGljaC5kZQAKCRChK+OYQpKeoYfMEACRMbLTKj2qBRlvJJEZczEiViN3
QgiatDtAFxI8VTgINqH2UzqFNd8Tg/4cvdrxpRgJsvIImyRvM0L40ZA+cjot6S/d
j1q/DtCjC2qXcdt0GF5qo+5/mIcPTERp7r8vLD8tT6raq9E/D8lfPLXEc5XD/ZIq
1m0WWLebDpmTWYduZYMhH7k8kdYSGXt84bkjT7RTs5C7gRRJFJcx/3wpfz9xO6K1
+rnS6A+f5EqA9BA8lgDLsFY3NOAmCx/7DXnTMpWaD5ecpNI0qrtsYmEmw5pBOryK
6UJ5AE4XYPTC1kpsGdKrf4lk2nz+k77CRkbec4O7zxYmLpJpqHz6HkWOgryHdf3Y
lrhG/oR3XGa1gq0PaL4z0W7id1+Ur1ACNtikH5rIZff06Bgvh8RA3RrQMV42S0os
fL35cjGTysxrHzyEJmy90g1AXRkZSBupZ1+/Owe9r0HoRJAJv/TfB1yBfjgXoL55
HEJ3BAFLyEGMiQtWawVkGJw0oqgNLX13K89Va4ZLZodSCf4BZfXCoZnvCINauKTd
daNzIRdvvHoMKj7rPl5VGXhRKtO8lxmz12b2CC0boInmwcKLZmVowbZcj3zkES95
jZxXkRanXWEfXGC7aPA2N9rCPcakH2l928gnG3xcVBeXaPAg0zL4ZpxUuo76aP2A
AgjVUeZL4LYojmaZfQ==
=7hcv
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20171006' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- Cleanup patches to make checkpatch happy, by Sven Eckelmann (3 patches)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass extack to do_set_master and down to ndo_add_slave
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 242c1a28eb ("net: Remove useless function skb_header_release")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
checkpatch introduced with commit 63b7c73ec8 ("checkpatch: add --strict
check for ifs with unnecessary parentheses") an additional test which
identifies some unnecessary parentheses.
Remove these unnecessary parentheses to avoid the warnings and to unify the
coding style slightly more.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
There is no one which would invokes the function skb_header_release.
So just remove it now.
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Network devices can allocate reasources and private memory using
netdev_ops->ndo_init(). However, the release of these resources
can occur in one of two different places.
Either netdev_ops->ndo_uninit() or netdev->destructor().
The decision of which operation frees the resources depends upon
whether it is necessary for all netdev refs to be released before it
is safe to perform the freeing.
netdev_ops->ndo_uninit() presumably can occur right after the
NETDEV_UNREGISTER notifier completes and the unicast and multicast
address lists are flushed.
netdev->destructor(), on the other hand, does not run until the
netdev references all go away.
Further complicating the situation is that netdev->destructor()
almost universally does also a free_netdev().
This creates a problem for the logic in register_netdevice().
Because all callers of register_netdevice() manage the freeing
of the netdev, and invoke free_netdev(dev) if register_netdevice()
fails.
If netdev_ops->ndo_init() succeeds, but something else fails inside
of register_netdevice(), it does call ndo_ops->ndo_uninit(). But
it is not able to invoke netdev->destructor().
This is because netdev->destructor() will do a free_netdev() and
then the caller of register_netdevice() will do the same.
However, this means that the resources that would normally be released
by netdev->destructor() will not be.
Over the years drivers have added local hacks to deal with this, by
invoking their destructor parts by hand when register_netdevice()
fails.
Many drivers do not try to deal with this, and instead we have leaks.
Let's close this hole by formalizing the distinction between what
private things need to be freed up by netdev->destructor() and whether
the driver needs unregister_netdevice() to perform the free_netdev().
netdev->priv_destructor() performs all actions to free up the private
resources that used to be freed by netdev->destructor(), except for
free_netdev().
netdev->needs_free_netdev is a boolean that indicates whether
free_netdev() should be done at the end of unregister_netdevice().
Now, register_netdevice() can sanely release all resources after
ndo_ops->ndo_init() succeeds, by invoking both ndo_ops->ndo_uninit()
and netdev->priv_destructor().
And at the end of unregister_netdevice(), we invoke
netdev->priv_destructor() and optionally call free_netdev().
Signed-off-by: David S. Miller <davem@davemloft.net>
- bump version strings, by Simon Wunderlich
- Code and Style cleanups, by Sven Eckelmann (5 patches)
- Remove an unneccessary memset, by Tobias Klauser
- DAT and BLA optimizations for various corner cases, by Andreas Pape
(5 patches)
- forward/rebroadcast packet restructuring, by Linus Luessing
(2 patches)
- ethtool cleanup and remove unncessary code, by Sven Eckelmann
(4 patches)
- use net_device_stats from net_device instead of private copy,
by Tobias Klauser
-----BEGIN PGP SIGNATURE-----
iQJKBAABCgA0FiEE1ilQI7G+y+fdhnrfoSvjmEKSnqEFAljmSyUWHHN3QHNpbW9u
d3VuZGVybGljaC5kZQAKCRChK+OYQpKeodYrD/4xzy0IGyF7vb/q3Nj0EeioldL8
/8j9G14RfnlQaTIGxHEYz6oo1A6+cuH+t/4N+ilPFv6F0bBXG3GsWYrBCYLhVKwu
2BQcoXC4ysdVqdrc7UDG5JY/t+n7JwhIcBw6kta9mt5fFVmPI/KHpefeaiUkdJb4
23YkYsOSPVcD/Yv6+uiyfOG8FFxDrqFyn1uHpE1K5/05jLhJJ8S7nODNsitMOv2m
EMLNJwTstSK/boPoxIpSCraxZGgpb0rt0K6HiBiNq0GyGRCtz0pxBpDOikVwTB62
hy2aW3R59baGHPxA47oOAF60cJUlTj4pYxmsGwd9hzeJkw4eMvcYJzW6/2PXB3bj
e4xBT5T+Y3bZDFdK+jW4hOCHLGC6gpwWSs5P6YDhCalhJ/meV75ef03ruIvGhVh9
qOhuSMAnqCsoJ8FMpLT3GMkSGSkOXEhL8iF/r3/PR/q0cPCquQnMjQg+Kqp7+eb6
iNHwSA0dqUiBB7KplS8KTcAxre8KlmNmGr544KY9eK0BZZ9BOleT2a2W7+QSTCKx
o8fl44HmwhgxQ+mYJwG1kEfgmTRhvrOmr6KP9qTkn5lAoIGXspwBo/bA5+cyLJOU
ewsx8JG5gfT2yUFB1HqdZon+rkW6KKopdHL+BL3BvQRYTUojxmr0lJBrMWg7GNYv
2lwrasmHxhWbF2L4xg==
=r99K
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20170406' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature/cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- Code and Style cleanups, by Sven Eckelmann (5 patches)
- Remove an unneccessary memset, by Tobias Klauser
- DAT and BLA optimizations for various corner cases, by Andreas Pape
(5 patches)
- forward/rebroadcast packet restructuring, by Linus Luessing
(2 patches)
- ethtool cleanup and remove unncessary code, by Sven Eckelmann
(4 patches)
- use net_device_stats from net_device instead of private copy,
by Tobias Klauser
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a private copy of struct net_device_stats in struct
batadv_priv, use stats from struct net_device.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The ethtool code was spread in soft-interface.c. This makes reading the
code and working on it unnecessary complicated. Having everything in a
common place next to the other code which references it, makes it slightly
easier.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
David S. Miller