Add the new Family 17h Model 70h PCI IDs (device 18h functions 0 and 6)
to the AMD64 EDAC module.
[ bp: s/f17_base_addr_to_cs_size/f17_addr_mask_to_cs_size/g ]
Signed-off-by: Isaac Vaughn <isaac.vaughn@knights.ucf.edu>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: James Morse <james.morse@arm.com>
Cc: linux-edac@vger.kernel.org
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Robert Richter <rrichter@marvell.com>
Cc: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20190906192131.8ced0ca112146f32d82b6cae@knights.ucf.edu
Debug messages are inconsistently used in the error handlers. Some lack
an error message, some are called regardless of the return status,
messages for the same error are at different locations in the code
depending on the error code. This happens esp. near put_device() calls.
Make those debug messages more consistent. Additionally, unify the error
messages to have the same terms for the same operations of the device.
Signed-off-by: Robert Richter <rrichter@marvell.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: "linux-edac@vger.kernel.org" <linux-edac@vger.kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20190902123216.9809-5-rrichter@marvell.com
Use of 'unsigned int' instead of bare use of 'unsigned'. Fix this for
edac_mc*, ghes and the i5100 driver as reported by checkpatch.pl.
While at it, struct member dev_ch_attribute->channel is always used as
unsigned int. Change type to unsigned int to avoid type casts.
[ bp: Massage. ]
Signed-off-by: Robert Richter <rrichter@marvell.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: "linux-edac@vger.kernel.org" <linux-edac@vger.kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20190902123216.9809-2-rrichter@marvell.com
The Armada 38x and other integrated SoCs use a reduced pin count so the
width of the SDRAM interface is smaller than the Armada XP SoCs. This
means that the definition of "full" and "half" width is reduced from
64/32 to 32/16.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Add support for the ECC functionality as found in the DDR RAM and L2
cache controllers on the MV78230/MV78x60 SoCs. This driver has been
tested on the MV78460 (on a custom board with a DDR3 ECC DIMM).
[cp use SPDX license]
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
We already have wrappers for x8 and x16, so add the missing x32 one.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Currently big microservers have _XEON_D while small microservers have
_X, Make it uniformly: _D.
for i in `git grep -l "\(INTEL_FAM6_\|VULNWL_INTEL\|INTEL_CPU_FAM6\).*_\(X\|XEON_D\)"`
do
sed -i -e 's/\(\(INTEL_FAM6_\|VULNWL_INTEL\|INTEL_CPU_FAM6\).*ATOM.*\)_X/\1_D/g' \
-e 's/\(\(INTEL_FAM6_\|VULNWL_INTEL\|INTEL_CPU_FAM6\).*\)_XEON_D/\1_D/g' ${i}
done
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Cc: x86@kernel.org
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Link: https://lkml.kernel.org/r/20190827195122.677152989@infradead.org
Future AMD systems will support asymmetric dual-rank DIMMs. These are
DIMMs where the ranks are of different sizes.
The even rank will use the Primary Even Chip Select registers and the
odd rank will use the Secondary Odd Chip Select registers.
Recognize if a Secondary Odd Chip Select is being used. Use the
Secondary Odd Address Mask when calculating the chip select size.
[ bp: move csrow_sec_enabled() to the header, fix CS_ODD define and
tone-down the capitalized words spelling. ]
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "linux-edac@vger.kernel.org" <linux-edac@vger.kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20190821235938.118710-8-Yazen.Ghannam@amd.com
AMD Family 17h systems have a set of secondary Chip Select Base
Addresses and Address Masks. These do not represent unique Chip
Selects, rather they are used in conjunction with the primary
Chip Select registers in certain cases.
Cache these secondary Chip Select registers for future use.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "linux-edac@vger.kernel.org" <linux-edac@vger.kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20190821235938.118710-7-Yazen.Ghannam@amd.com
AMD Family 17h systems currently require address translation in order to
report the system address of a DRAM ECC error. This is currently done
before decoding the syndrome information. The syndrome information does
not depend on the address translation, so the proper EDAC csrow/channel
reporting can function without the address. However, the syndrome
information will not be decoded if the address translation fails.
Decode the syndrome information before doing the address translation.
The syndrome information is architecturally defined in MCA_SYND and can
be considered robust. The address translation is system-specific and may
fail on newer systems without proper updates to the translation
algorithm.
Fixes: 713ad54675 ("EDAC, amd64: Define and register UMC error decode function")
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "linux-edac@vger.kernel.org" <linux-edac@vger.kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20190821235938.118710-6-Yazen.Ghannam@amd.com
Chip Select memory size reporting on AMD Family 17h was recently fixed
in order to account for interleaving. However, the current method is not
robust.
The Chip Select Address Mask can be used to find the memory size. There
are a couple of cases.
1) For single-rank and dual-rank non-interleaved, use the address mask
plus 1 as the size.
2) For dual-rank interleaved, do #1 but "de-interleave" the address mask
first.
Always "de-interleave" the address mask in order to simplify the code
flow. Bit mask manipulation is necessary to check for interleaving, so
just go ahead and do the de-interleaving. In the non-interleaved case,
the original and de-interleaved address masks will be the same.
To de-interleave the mask, count the number of zero bits in the middle
of the mask and swap them with the most significant bits.
For example,
Original=0xFFFF9FE, De-interleaved=0x3FFFFFE
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "linux-edac@vger.kernel.org" <linux-edac@vger.kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20190821235938.118710-5-Yazen.Ghannam@amd.com
Currently, the DIMM info for AMD Family 17h systems is initialized in
init_csrows(). This function is shared with legacy systems, and it has a
limit of two channel support.
This prevents initialization of the DIMM info for a number of ranks, so
there will be missing ranks in the EDAC sysfs.
Create a new init_csrows_df() for Family17h+ and revert init_csrows()
back to pre-Family17h support.
Loop over all channels in the new function in order to support systems
with more than two channels.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "linux-edac@vger.kernel.org" <linux-edac@vger.kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20190821235938.118710-4-Yazen.Ghannam@amd.com
AMD Family 17h systems support x4 and x16 DRAM devices. However, the
device type is not checked when setting mci.edac_ctl_cap.
Set the appropriate capability flag based on the device type.
Default to x8 DRAM device when neither the x4 or x16 bits are set.
[ bp: reverse cpk_en check to save an indentation level. ]
Fixes: 2d09d8f301 ("EDAC, amd64: Determine EDAC MC capabilities on Fam17h")
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "linux-edac@vger.kernel.org" <linux-edac@vger.kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20190821235938.118710-3-Yazen.Ghannam@amd.com
The struct chip_select array that's used for saving chip select bases
and masks is fixed at length of two. There should be one struct
chip_select for each controller, so this array should be increased to
support systems that may have more than two controllers.
Increase the size of the struct chip_select array to eight, which is the
largest number of controllers per die currently supported on AMD
systems.
Fix number of DIMMs and Chip Select bases/masks on Family17h, because
AMD Family 17h systems support 2 DIMMs, 4 CS bases, and 2 CS masks per
channel.
Also, carve out the Family 17h+ reading of the bases/masks into a
separate function. This effectively reverts the original bases/masks
reading code to before Family 17h support was added.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "linux-edac@vger.kernel.org" <linux-edac@vger.kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20190821235938.118710-2-Yazen.Ghannam@amd.com
Depending on how BIOS has marked the reserved region containing the 32KB
MCHBAR you can get warnings like:
resource sanity check: requesting [mem 0xfed10000-0xfed1ffff], which spans more than reserved [mem 0xfed10000-0xfed17fff]
caller dnv_rd_reg+0xc8/0x240 [pnd2_edac] mapping multiple BARs
Not all of the mmio regions used in dnv_rd_reg() are the same size. The
MCHBAR window is 32KB and the sideband ports are 64KB. Pass the correct
size to ioremap() depending on which resource we're reading from.
Signed-off-by: Stephen Douthit <stephend@silicom-usa.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add ECC support for Mellanox BlueField SoC DDR controller.
This requires SMC to the running Arm Trusted Firmware to report
what is the current memory configuration.
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Shravan Kumar Ramani <sramani@mellanox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Smatch complains about the cast of a u32 pointer to unsigned long:
drivers/edac/altera_edac.c:1878 altr_edac_a10_irq_handler()
warn: passing casted pointer '&irq_status' to 'find_first_bit()'
This code wouldn't work on a 64 bit big endian system because it would
read past the end of &irq_status.
[ bp: massage. ]
Fixes: 13ab8448d2 ("EDAC, altera: Add ECC Manager IRQ controller support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Thor Thayer <thor.thayer@linux.intel.com>
Cc: James Morse <james.morse@arm.com>
Cc: kernel-janitors@vger.kernel.org
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20190624134717.GA1754@mwanda
The grain in EDAC is defined as "minimum granularity for an error
report, in bytes". The following calculation of the grain_bits in
edac_mc is wrong:
grain_bits = fls_long(e->grain) + 1;
Where grain_bits is defined as:
grain = 1 << grain_bits
Example:
grain = 8 # 64 bit (8 bytes)
grain_bits = fls_long(8) + 1
grain_bits = 4 + 1 = 5
grain = 1 << grain_bits
grain = 1 << 5 = 32
Replace it with the correct calculation:
grain_bits = fls_long(e->grain - 1);
The example gives now:
grain_bits = fls_long(8 - 1)
grain_bits = fls_long(7)
grain_bits = 3
grain = 1 << 3 = 8
Also, check if the hardware reports a reasonable grain != 0 and fallback
with a warning to 1 byte granularity otherwise.
[ bp: massage a bit. ]
Signed-off-by: Robert Richter <rrichter@marvell.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "linux-edac@vger.kernel.org" <linux-edac@vger.kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20190624150758.6695-2-rrichter@marvell.com
ARM32 SoCFPGAs had separate IRQs for SDRAM. ARM64 SoCFPGAs
send all DBEs to SError so filtering by source is necessary.
The Stratix10 SDRAM ECC is a better match with the generic
Altera peripheral ECC framework because the linked list can
be searched to find the ECC block offset and printout
the DBE Address.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Acked-by: James Morse <james.morse@arm.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit 9da21b1509 ("EDAC: Poll timeout cannot be zero, p2") assumes
edac_mc_poll_msec to be unsigned long, but the type of the variable still
remained as int. Setting edac_mc_poll_msec can trigger out-of-bounds
write.
Reproducer:
# echo 1001 > /sys/module/edac_core/parameters/edac_mc_poll_msec
KASAN report:
BUG: KASAN: global-out-of-bounds in edac_set_poll_msec+0x140/0x150
Write of size 8 at addr ffffffffb91b2d00 by task bash/1996
CPU: 1 PID: 1996 Comm: bash Not tainted 5.2.0-rc6+ #23
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-2.fc30 04/01/2014
Call Trace:
dump_stack+0xca/0x13e
print_address_description.cold+0x5/0x246
__kasan_report.cold+0x75/0x9a
? edac_set_poll_msec+0x140/0x150
kasan_report+0xe/0x20
edac_set_poll_msec+0x140/0x150
? dimmdev_location_show+0x30/0x30
? vfs_lock_file+0xe0/0xe0
? _raw_spin_lock+0x87/0xe0
param_attr_store+0x1b5/0x310
? param_array_set+0x4f0/0x4f0
module_attr_store+0x58/0x80
? module_attr_show+0x80/0x80
sysfs_kf_write+0x13d/0x1a0
kernfs_fop_write+0x2bc/0x460
? sysfs_kf_bin_read+0x270/0x270
? kernfs_notify+0x1f0/0x1f0
__vfs_write+0x81/0x100
vfs_write+0x1e1/0x560
ksys_write+0x126/0x250
? __ia32_sys_read+0xb0/0xb0
? do_syscall_64+0x1f/0x390
do_syscall_64+0xc1/0x390
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x7fa7caa5e970
Code: 73 01 c3 48 8b 0d 28 d5 2b 00 f7 d8 64 89 01 48 83 c8 ff c3 66 0f 1f 44 00 00 83 3d 99 2d 2c 00 00 75 10 b8 01 00 00 00 04
RSP: 002b:00007fff6acfdfe8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000000000000005 RCX: 00007fa7caa5e970
RDX: 0000000000000005 RSI: 0000000000e95c08 RDI: 0000000000000001
RBP: 0000000000e95c08 R08: 00007fa7cad1e760 R09: 00007fa7cb36a700
R10: 0000000000000073 R11: 0000000000000246 R12: 0000000000000005
R13: 0000000000000001 R14: 00007fa7cad1d600 R15: 0000000000000005
The buggy address belongs to the variable:
edac_mc_poll_msec+0x0/0x40
Memory state around the buggy address:
ffffffffb91b2c00: 00 00 00 00 fa fa fa fa 00 00 00 00 fa fa fa fa
ffffffffb91b2c80: 00 00 00 00 fa fa fa fa 00 00 00 00 fa fa fa fa
>ffffffffb91b2d00: 04 fa fa fa fa fa fa fa 04 fa fa fa fa fa fa fa
^
ffffffffb91b2d80: 04 fa fa fa fa fa fa fa 00 00 00 00 00 00 00 00
ffffffffb91b2e00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Fix it by changing the type of edac_mc_poll_msec to unsigned int.
The reason why this patch adopts unsigned int rather than unsigned long
is msecs_to_jiffies() assumes arg to be unsigned int. We can avoid
integer conversion bugs and unsigned int will be large enough for
edac_mc_poll_msec.
Reviewed-by: James Morse <james.morse@arm.com>
Fixes: 9da21b1509 ("EDAC: Poll timeout cannot be zero, p2")
Signed-off-by: Eiichi Tsukata <devel@etsukata.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The source ID register offset for Skylake server is 0xf0, while for
Icelake server is 0xf8. Pass the correct offset to get the source ID.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The i10nm_edac only checks the ECC enabling status for the first
channel of the memory controller. If there aren't memory DIMMs
populated on the first channel, but at least one DIMM populated
on the second channel, it will wrongly report that the ECC for
the memory controller is disabled that fails to load the i10nm_edac
driver. Fix it by checking ECC enabling status per channel.
[Tony: Also report which channel has ECC disabled]
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Two new CPU models share the same memory controller
architecture with Jacobsville/Tremont, so can use the
same i10nm EDAC driver.
Add ICX and ICX-D CPU model numbers for EDAC support.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The return values of edac_debugfs_create_x16() and
edac_debugfs_create_x8() are never checked (as they don't need to be),
so no need to have them return anything, just make the functions return
void instead.
This is done with the goal of being able to change the debugfs_create_x*
functions to also not return a value.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: James Morse <james.morse@arm.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Link: https://lkml.kernel.org/r/20190611175433.GA5108@kroah.com
Fix the following -Wunused-but-set-variable warning:
drivers/edac/aspeed_edac.c: In function aspeed_probe:
drivers/edac/aspeed_edac.c:284:22: warning: variable np set but not used [-Wunused-but-set-variable]
It is never used and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Stefan Schaeckeler <sschaeck@cisco.com>
Cc: James Morse <james.morse@arm.com>
Cc: Joel Stanley <joel@jms.id.au>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-aspeed@lists.ozlabs.org
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Link: https://lkml.kernel.org/r/20190525144153.2028-1-yuehaibing@huawei.com
Reformat device table after Coffee Lake additions to be more readable.
No functional change.
Signed-off-by: Marco Elver <elver@google.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Tony Luck <tony.luck@intel.com>
Cc: James Morse <james.morse@arm.com>
Cc: Jason Baron <jbaron@akamai.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Link: https://lkml.kernel.org/r/20190610191422.177931-2-elver@google.com
Coffee Lake seems to work like Skylake and Kaby Lake. Add all device IDs
for Coffee Lake-S CPUs according to datasheet.
[ bp: Massage. ]
Signed-off-by: Marco Elver <elver@google.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Tony Luck <tony.luck@intel.com>
Cc: James Morse <james.morse@arm.com>
Cc: Jason Baron <jbaron@akamai.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Link: https://lkml.kernel.org/r/20190610191422.177931-1-elver@google.com
Add an EDAC driver for SiFive SoCs. The initial version supports ECC
event monitoring and reporting through the EDAC framework for the SiFive
L2 cache controller. It registers for notifier events from the L2 cache
controller driver (arch/riscv/mm/sifive_l2_cache.c) for L2 ECC events.
[ bp: Massage commit message. ]
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: James Morse <james.morse@arm.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: linux-riscv@lists.infradead.org
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: "Paul E. McKenney" <paulmck@linux.ibm.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: sachin.ghadi@sifive.com
Link: https://lkml.kernel.org/r/1557142026-15949-2-git-send-email-yash.shah@sifive.com
The variable tad_base is being set to a value that is never read and is
being over-written on the next iteration of a for-loop. This assignment
is therefore redundant and can be removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Tony Luck <tony.luck@intel.com>
Cc: James Morse <james.morse@arm.com>
Cc: kernel-janitors@vger.kernel.org
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Link: https://lkml.kernel.org/r/20190508224201.27120-1-colin.king@canonical.com
Do put_device() if device_add() fails.
[ bp: do device_del() for the successfully created devices in
edac_create_csrow_objects(), on the unwind path. ]
Signed-off-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20190427214925.GE16338@kroah.com
In edac_create_csrow_object(), the reference to the object is not
released when adding the device to the device hierarchy fails
(device_add()). This may result in a memory leak.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: https://lkml.kernel.org/r/1555554438-103953-1-git-send-email-bianpan2016@163.com
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 315 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.503150771@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 59 temple place suite 330 boston ma 02111
1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 136 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.384967451@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 263 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 228 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.107155473@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this file may be distributed under the terms of the gnu general
public license version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 9 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.395589349@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see http www gnu org licenses
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details [based]
[from] [clk] [highbank] [c] you should have received a copy of the
gnu general public license along with this program if not see http
www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 355 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.837383322@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have EXPORT_.*_SYMBOL_GPL inside which was used in the
initial scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Correct edac_mc_find()'s return value on error (Robert Richter)
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEzv7L6UO9uDPlPSfHEsHwGGHeVUoFAlzdOjIACgkQEsHwGGHe
VUrkxQ/+J+mSL23ush4HNq43OqW7Wgpkdoljo+5hr1XWH790Kc/HNI+B/Qdsgl6I
UoFkJPwMTfxqV/JZFuNC22ADnrXw6nRDZSE7+K+fHmpBgj2rK4hQ6tOYON9dTg/X
9nPF1ylBQcdzwNt4eTTnS5U1eKBSWqmQm5NtYmq2s83DQ1v3r2Pckqx00SC5Stdy
9vQLCPUR5SjsGpeQZnrdesxO89t3pWWzfZrAsCxPiY36VbUVmsHQVbHC9yfpLSIE
6pzc0esQx6zqyb4e0Rx+aKJPJ6fS43NsxifkI81h7S5F/xPEuZy39rhAmnEOYCNE
0ceQwl+ktzzGzmurgXf9Y5LLy8vOcCUJX4HBCkaweHSDRiP1xZtIl7Ao3aAaP4no
AUQqX/O0BydkO+awarhCduM7vIGdr0B9xn0xCtUODitoTIzaoVZ8F2iF7xSOi/3F
QkP4dSsf72ZK/EdA/8k1bxyBnxQ/TKgwLIQEJ1n9Bz7biPxZmqCyHQMDg7HaA1Uc
crGkJJr0cGHb9TEAzy0ygtRNrKE+hpt0FGFGE0zlE4uX7YP1Y/Bw3R38zbcl2x9h
nIqEmHwswVfBdm28RfxRH3LnS9SHwsXTtUk0y89Je1pK0qZ2Kv6nRiEFzWIAqPyY
I/7eorSkNXU+vVnZko8cvuHEuJh1VUj2bGJeS6NUo9X5+IOE0LE=
=yjXI
-----END PGP SIGNATURE-----
Merge tag 'edac_fixes_for_5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC fixes from Borislav Petkov:
- Do not build mpc85_edac as a module (Michael Ellerman)
- Correct edac_mc_find()'s return value on error (Robert Richter)
* tag 'edac_fixes_for_5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC/mc: Fix edac_mc_find() in case no device is found
EDAC/mpc85xx: Prevent building as a module
The function should return NULL in case no device is found, but it
always returns the last checked mc device from the list even if the
index did not match. Fix that.
I did some analysis why this did not raise any issues for about 3 years
and the reason is that edac_mc_find() is mostly used to search for
existing devices. Thus, the bug is not triggered.
[ bp: Drop the if (mci->mc_idx > idx) test in favor of readability. ]
Fixes: c73e8833be ("EDAC, mc: Fix locking around mc_devices list")
Signed-off-by: Robert Richter <rrichter@marvell.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "linux-edac@vger.kernel.org" <linux-edac@vger.kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Link: https://lkml.kernel.org/r/20190514104838.15065-1-rrichter@marvell.com
The mpc85xx EDAC driver can be configured as a module but then fails to
build because it uses two unexported symbols:
ERROR: ".pci_find_hose_for_OF_device" [drivers/edac/mpc85xx_edac_mod.ko] undefined!
ERROR: ".early_find_capability" [drivers/edac/mpc85xx_edac_mod.ko] undefined!
We don't want to export those symbols just for this driver, so make the
driver only configurable as a built-in.
This seems to have been broken since at least
c92132f598 ("edac/85xx: Add PCIe error interrupt edac support")
(Nov 2013).
[ bp: make it depend on EDAC=y so that the EDAC core doesn't get built
as a module. ]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: linuxppc-dev@ozlabs.org
Cc: morbidrsa@gmail.com
Link: https://lkml.kernel.org/r/20190502141941.12927-1-mpe@ellerman.id.au
Pull RAS updates from Borislav Petkov:
- Support for varying MCA bank numbers per CPU: this is in preparation
for future CPU enablement (Yazen Ghannam)
- MCA banks read race fix (Tony Luck)
- Facility to filter MCEs which should not be logged (Yazen Ghannam)
- The usual round of cleanups and fixes
* 'ras-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/MCE/AMD: Don't report L1 BTB MCA errors on some family 17h models
x86/MCE: Add an MCE-record filtering function
RAS/CEC: Increment cec_entered under the mutex lock
x86/mce: Fix debugfs_simple_attr.cocci warnings
x86/mce: Remove mce_report_event()
x86/mce: Handle varying MCA bank counts
x86/mce: Fix machine_check_poll() tests for error types
MAINTAINERS: Fix file pattern for X86 MCE INFRASTRUCTURE
x86/MCE: Group AMD function prototypes in <asm/mce.h>
AMD family 17h Models 10h-2Fh may report a high number of L1 BTB MCA
errors under certain conditions. The errors are benign and can safely be
ignored. However, the high error rate may cause the MCA threshold
counter to overflow causing a high rate of thresholding interrupts.
In addition, users may see the errors reported through the AMD MCE
decoder module, even with the interrupt disabled, due to MCA polling.
Clear the "Counter Present" bit in the Instruction Fetch bank's
MCA_MISC0 register. This will prevent enabling MCA thresholding on this
bank which will prevent the high interrupt rate due to this error.
Define an AMD-specific function to filter these errors from the MCE
event pool so that they don't get reported during early boot.
Rename filter function in EDAC/mce_amd to avoid a naming conflict, while
at it.
[ bp: Move function prototype to the internal header and
massage/cleanup, fix typos. ]
Reported-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "clemej@gmail.com" <clemej@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morse <james.morse@arm.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Pu Wen <puwen@hygon.cn>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: Shirish S <Shirish.S@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: x86-ml <x86@kernel.org>
Cc: <stable@vger.kernel.org> # 5.0.x: c95b323dcd35: x86/MCE/AMD: Turn off MC4_MISC thresholding on all family 0x15 models
Cc: <stable@vger.kernel.org> # 5.0.x: 30aa3d26edb0: x86/MCE/AMD: Carve out the MC4_MISC thresholding quirk
Cc: <stable@vger.kernel.org> # 5.0.x: 9308fd407455: x86/MCE: Group AMD function prototypes in <asm/mce.h>
Cc: <stable@vger.kernel.org> # 5.0.x
Link: https://lkml.kernel.org/r/20190325163410.171021-2-Yazen.Ghannam@amd.com
Reserve ECC Double Bit Error SMC call to alert U-Boot that a DBE has
occurred. Move the call from local EDAC header file to a common header.
[ bp: Merge the two patches. ]
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Richard Gong <richard.gong@intel.com>
Reviewed-by: Alan Tull <atull@kernel.org> # firmware
Cc: Greg KH <greg@kroah.com>
Cc: James Morse <james.morse@arm.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: mchehab@kernel.org
Link: https://lkml.kernel.org/r/1553870639-23895-1-git-send-email-thor.thayer@linux.intel.com
Signed-off-by: Borislav Petkov <bp@suse.de>
The FIFO memory and ECC initialization doesn't need to be
done as a separate operation early in the startup.
Improve the Arria10 and Stratix10 peripheral FIFO init
by initializing memory and enabling ECC as part of the
device driver initialization.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: https://lkml.kernel.org/r/1553635771-32693-2-git-send-email-thor.thayer@linux.intel.com
Improve the Arria10 and Stratix10 error injection routine
by reading the data and changing just 1 bit before writing
back out. Previous routine would overwrite the first bytes
to 0 then change 1 bit but this method is less intrusive.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: https://lkml.kernel.org/r/1553635771-32693-1-git-send-email-thor.thayer@linux.intel.com
AMD systems may support chip select interleaving. However, on family
17h+ this was not taken into account when printing the chip select
sizes.
Add support to detect if chip selects are interleaved on family 17h+,
and adjust the sizes accordingly.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Kim Phillips <kim.phillips@amd.com>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: https://lkml.kernel.org/r/20190228153558.127292-6-Yazen.Ghannam@amd.com
The struct chip_select array that's used for saving chip select bases
and masks is fixed at length of two. There should be one struct
chip_select for each controller, so this array should be increased to
support systems that may have more than two controllers.
Increase the size of the struct chip_select array to eight, which is the
largest number of controllers per die currently supported on AMD
systems.
Also, carve out the Family 17h+ reading of the bases/masks into a
separate function. This effectively reverts the original bases/masks
reading code to before Family 17h support was added.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Kim Phillips <kim.phillips@amd.com>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: https://lkml.kernel.org/r/20190228153558.127292-5-Yazen.Ghannam@amd.com
Future AMD systems may support x16 symbol sizes.
Recognize if a system is using x16 symbol size. Also, simplify the print
statement.
Note that a x16 syndrome vector table is not necessary like with x4 or
x8 syndromes. This is because systems that support x16 symbol sizes are
SMCA systems and in that case, the syndrome can be directly extracted
from the MCA_SYND[Syndrome] field.
[ bp: massage. ]
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Kim Phillips <kim.phillips@amd.com>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: https://lkml.kernel.org/r/20190228153558.127292-4-Yazen.Ghannam@amd.com
The AMD64 EDAC module currently hardcodes the EDAC channel layer size
count to two. Future AMD systems may have more channels than this.
Set the EDAC channel layer size equal to the maximum number of channels
possible for the system. On Family 17h and later, this is set in the
num_umcs variable. Older systems will continue to use two as the
default.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: https://lkml.kernel.org/r/20190325203319.7603-1-Yazen.Ghannam@amd.com
The first few models of Family 17h all had 2 Unified Memory Controllers
per Die, so this was treated as a fixed value. However, future systems
may have more Unified Memory Controllers per Die.
Related to this, the channel number and base address of a Unified Memory
Controller were found by matching on fixed, known values. However,
current and future systems follow this pattern for the channel number
and base address of a Unified Memory Controller: 0xYXXXXX, where Y is
the channel number. So matching on hardcoded values is not necessary.
Set the number of Unified Memory Controllers at driver init time based
on the family/model. Also, update the functions that find the channel
number and base address of a Unified Memory Controller to support more
than two.
[ bp: Move num_umcs into the .c file and simplify comment. ]
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Kim Phillips <kim.phillips@amd.com>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: https://lkml.kernel.org/r/20190228153558.127292-3-Yazen.Ghannam@amd.com
Define and use a macro for looping over the number of Unified Memory
Controllers.
No functional change.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Kim Phillips <kim.phillips@amd.com>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: https://lkml.kernel.org/r/20190228153558.127292-2-Yazen.Ghannam@amd.com
Add the new Family 17h Model 30h PCI IDs to the AMD64 EDAC module.
This also fixes a probe failure that appeared when some other PCI IDs
for Family 17h Model 30h were added to the AMD NB code.
Fixes: be3518a16e (x86/amd_nb: Add PCI device IDs for family 17h, model 30h)
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Kim Phillips <kim.phillips@amd.com>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: https://lkml.kernel.org/r/20190228153558.127292-1-Yazen.Ghannam@amd.com
Stratix10 Double Bit Error Address was always read from SDRAM Address
register instead of each device's Address register.
To determine which device had the DBE, cycle through the EDAC devices
comparing the DBE value to the db_irq value. Once found, report the DBE
Address from the device registers as well as the device name.
Finally, notify the system via an SMC call and indicate the panic should
result in a system reboot. Change a run-time check to a Stratix10
compile-time check for a clean SMC notification.
Fixes: d5fc912556 ("EDAC, altera: Combine Stratix10 and Arria10 probe functions")
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: https://lkml.kernel.org/r/1552490842-25440-1-git-send-email-thor.thayer@linux.intel.com
The following Kconfig constellations fail randconfig builds:
CONFIG_ACPI_NFIT=y
CONFIG_EDAC_DEBUG=y
CONFIG_EDAC_SKX=m
CONFIG_EDAC_I10NM=y
or
CONFIG_ACPI_NFIT=y
CONFIG_EDAC_DEBUG=y
CONFIG_EDAC_SKX=y
CONFIG_EDAC_I10NM=m
with:
...
CC [M] drivers/edac/skx_common.o
...
.../skx_common.o:.../skx_common.c:672: undefined reference to `__this_module'
That is because if one of the two drivers - skx_edac or i10nm_edac - is
built-in and the other one is a module, the shared file skx_common.c
gets linked into a module object by kbuild. Therefore, when linking that
same file into vmlinux, the '__this_module' symbol used in debugfs isn't
defined, leading to the above error.
Fix it by moving all debugfs code from skx_common.c to both skx_base.c
and i10nm_base.c respectively. Thus, skx_common.c doesn't refer to the
'__this_module' symbol anymore.
Clarify skx_common.c's purpose at the top of the file for future
reference, while at it.
[ bp: Make text more readable. ]
Fixes: d4dc89d069 ("EDAC, i10nm: Add a driver for Intel 10nm server processors")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: https://lkml.kernel.org/r/20190321221339.GA32323@agluck-desk
Pull RAS updates from Borislav Petkov:
"This time around we have in store:
- Disable MC4_MISC thresholding banks on all AMD family 0x15 models
(Shirish S)
- AMD MCE error descriptions update and error decode improvements
(Yazen Ghannam)
- The usual smaller conversions and fixes"
* 'ras-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce: Improve error message when kernel cannot recover, p2
EDAC/mce_amd: Decode MCA_STATUS in bit definition order
EDAC/mce_amd: Decode MCA_STATUS[Scrub] bit
EDAC, mce_amd: Print ExtErrorCode and description on a single line
EDAC, mce_amd: Match error descriptions to latest documentation
x86/MCE/AMD, EDAC/mce_amd: Add new error descriptions for some SMCA bank types
x86/MCE/AMD, EDAC/mce_amd: Add new McaTypes for CS, PSP, and SMU units
x86/MCE/AMD, EDAC/mce_amd: Add new MP5, NBIO, and PCIE SMCA bank types
RAS: Add a MAINTAINERS entry
RAS: Use consistent types for UUIDs
x86/MCE/AMD: Carve out the MC4_MISC thresholding quirk
x86/MCE/AMD: Turn off MC4_MISC thresholding on all family 0x15 models
x86/MCE: Switch to use the new generic UUID API
* New i10nm EDAC driver for Intel 10nm CPUs (Qiuxu Zhuo and Tony Luck)
* Altera SDRAM functionality carveout for separate enablement of RAS and
SDRAM capabilities on some Altera chips. (Thor Thayer)
* The usual round of cleanups and fixes
Last but not least:
* Recruit James Morse as a reviewer for the ARM side
-----BEGIN PGP SIGNATURE-----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=A1kA
-----END PGP SIGNATURE-----
Merge tag 'edac_for_5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC updates from Borislav Petkov:
- A new EDAC AST 2500 SoC driver (Stefan M Schaeckeler)
- New i10nm EDAC driver for Intel 10nm CPUs (Qiuxu Zhuo and Tony Luck)
- Altera SDRAM functionality carveout for separate enablement of RAS
and SDRAM capabilities on some Altera chips. (Thor Thayer)
- The usual round of cleanups and fixes
And last but not least: recruit James Morse as a reviewer for the ARM
side.
* tag 'edac_for_5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC/altera: Add separate SDRAM EDAC config
EDAC, altera: Add missing of_node_put()
EDAC, skx_common: Add code to recognise new compound error code
EDAC, i10nm: Fix randconfig builds
EDAC, i10nm: Add a driver for Intel 10nm server processors
EDAC, skx_edac: Delete duplicated code
EDAC, skx_common: Separate common code out from skx_edac
EDAC: Do not check return value of debugfs_create() functions
EDAC: Add James Morse as a reviewer
dt-bindings, EDAC: Add Aspeed AST2500
EDAC, aspeed: Add an Aspeed AST2500 EDAC driver
The CONFIG_ALTERA_EDAC Kconfig symbol always enables the SDRAM EDAC
functionality. On the newer architectures, however, there are cases
where the peripheral EDAC functionality is enabled but SDRAM needs to be
disabled.
Move SDRAM functions so they can be contained inside the conditional
CONFIG. Create new CONFIG option just for SDRAM.
[ bp: Massage commit message. ]
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: dinguyen@kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: linux@armlinux.org.uk
Link: https://lkml.kernel.org/r/1551121006-4657-2-git-send-email-thor.thayer@linux.intel.com
Previous AMD systems have had a bit in MCA_STATUS to indicate that an
error was detected on a scrub operation. However, this bit was defined
differently within different banks and families/models.
Starting with Family 17h, MCA_STATUS[40] is either Reserved/Read-as-Zero
or defined as "Scrub", for all MCA banks and CPU models. Therefore, this
bit can be defined as the "Scrub" bit.
Define MCA_STATUS[40] as "Scrub" and decode it in the AMD MCE decoding
module for Family 17h and newer systems.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morse <james.morse@arm.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Pu Wen <puwen@hygon.cn>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190212212417.107049-1-Yazen.Ghannam@amd.com
The call to of_parse_phandle() returns a node pointer with refcount
incremented thus it must be explicitly decremented here after the last
usage.
Signed-off-by: Huang Zijiang <huang.zijiang@zte.com.cn>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Thor Thayer <thor.thayer@linux.intel.com>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: wang.yi59@zte.com.cn
Link: https://lkml.kernel.org/r/1550126347-27984-1-git-send-email-huang.zijiang@zte.com.cn
A new error code for systems that use DRAM as an extra level of cache
looks like:
000F 0010 1MMM CCCC
where the MMM and CCCC bits are used for the same purpose as the
original code. For this new class of errors the ADXL translation will
provide details of both the DIMM used as cache for the error location
and the component that is being cached.
Note: This new error code is first supported in Skylake. Older EDAC
drivers do not need to be updated.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Aristeu Rozanski <aris@redhat.com>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: https://lkml.kernel.org/r/20190205182109.27828-1-tony.luck@intel.com
Save a log line by printing the extended error code and the description
on a single line. This is similar to how errors are printed in other
subsystems, e.g. "#, description". If we don't have a valid description
then only the number/code is printed.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: x86@kernel.org
Link: https://lkml.kernel.org/r/20190201225534.8177-6-Yazen.Ghannam@amd.com
Update the error descriptions to match the latest documentation for
easier searching. In some cases the changes are small and in other cases
the changes may be total rewording of the description.
No functional changes.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: x86@kernel.org
Link: https://lkml.kernel.org/r/20190201225534.8177-5-Yazen.Ghannam@amd.com
Some SMCA bank types on future systems will report new error types even
though the bank type is not treated as a new version. These new error
types will reported by bits that are reserved in past systems.
Add the new error descriptions to the lists in edac_mce_amd.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Shirish S <Shirish.S@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190201225534.8177-4-Yazen.Ghannam@amd.com
The existing CS, PSP, and SMU SMCA bank types will see new versions (as
indicated by their McaTypes) in future SMCA systems.
Add the new (HWID, MCATYPE) tuples for these new versions. Reuse the
same names as the older versions, since they are logically the same to
the user. SMCA systems won't mix and match IP blocks with different
McaType versions in the same system, so there isn't a need to
distinguish them. The MCA_IPID register is saved when logging an MCA
error, and that can be used to triage the error.
Also, add the new error descriptions to edac_mce_amd. Some error types
(positions in the list) are overloaded compared to the previous
McaTypes. Therefore, just create new lists of the error descriptions to
keep things simple even if some of the error descriptions are the same
between versions.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Pu Wen <puwen@hygon.cn>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: Shirish S <Shirish.S@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190201225534.8177-3-Yazen.Ghannam@amd.com
This driver supports the Intel 10nm series server integrated memory
controller. It gets the memory capacity and topology information by
reading the registers in PCI configuration space and memory-mapped I/O.
It decodes the memory error address to the platform specific address
by using the ACPI Address Translation (ADXL) Device Specific Method
(DSM).
Co-developed-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: https://lkml.kernel.org/r/20190130191519.15393-5-tony.luck@intel.com
Delete the duplicated code from skx_edac.c and rename skx_edac.c to
skx_base.c. Update the Makefile to build the skx_edac driver from
skx_base.c and skx_common.c.
Add SPDX to skx_base.c and clean out unnecessary #include lines.
[ bp: Drop the license boilerplate - there's an SPDX identifier now. ]
Co-developed-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: https://lkml.kernel.org/r/20190130191519.15393-4-tony.luck@intel.com
Parts of skx_edac can be shared with the Intel 10nm server EDAC driver.
Carve out the common parts from skx_edac in preparation to support both
skx_edac driver and i10nm_edac drivers.
Co-developed-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: https://lkml.kernel.org/r/20190130191519.15393-3-tony.luck@intel.com
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
[ bp: Make edac_debugfs_init() return void too, while at it. ]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: https://lkml.kernel.org/r/20190122152151.16139-17-gregkh@linuxfoundation.org
Gate error injection feature with CONFIG_EDAC_DEBUG so that it is not
visible in production setups.
Suggested-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: York Sun <york.sun@nxp.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: https://lkml.kernel.org/r/20181119225303.13265-1-york.sun@nxp.com
Current debugfs shows the decoded result in its own print format which
is inconvenient for analysis/statistics.
Use skx_mce_check_error() instead of skx_decode() for debugfs,
then the decoded result is showed via EDAC core in a more readable
format like "CPU_SrcID#[0-9]_MC#[0-9]_Chan#[0-9]_DIMM#[0-9]".
Print a warning the first time this interface is used so the
administrator can see the console log that error(s) have been faked.
Co-developed-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
CC: Mauro Carvalho Chehab <mchehab@kernel.org>
CC: arozansk@redhat.com
CC: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1542353705-13531-1-git-send-email-qiuxu.zhuo@intel.com
The debugfs node is /sys/kernel/debug/skx_edac_test. Rename it and move
under EDAC debugfs root directory. Remove the unused 'skx_fake_addr' and
remove the 'skx_test' on error.
Co-developed-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
CC: Mauro Carvalho Chehab <mchehab@kernel.org>
CC: arozansk@redhat.com
CC: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1542353684-13496-1-git-send-email-qiuxu.zhuo@intel.com
Some debug/error strings in hex formatting do not have the '0x' prefix.
Prepend hex formatting with '0x' for them, but with one exception:
"Couldn't enable %04x:%04x", instead of putting '0x' in this line,
add the word 'device'. We commonly use 8086:1234 without the leading
'0x' (e.g. as '-d' argument to lspci(8) and setpci(8) commands).
Suggested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
CC: Mauro Carvalho Chehab <mchehab@kernel.org>
CC: Tony Luck <tony.luck@intel.com>
CC: arozansk@redhat.com
CC: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1542353660-13458-1-git-send-email-qiuxu.zhuo@intel.com
The order of function calling in skx_exit() is not the reversed order in
skx_init(). Fix it.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
CC: Mauro Carvalho Chehab <mchehab@kernel.org>
CC: Tony Luck <tony.luck@intel.com>
CC: arozansk@redhat.com
CC: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1542353616-13421-1-git-send-email-qiuxu.zhuo@intel.com
... and use the single edac_subsys object returned from
subsys_system_register(). The idea is to have a single bus
and multiple devices on it.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
CC: Aristeu Rozanski Filho <arozansk@redhat.com>
CC: Greg KH <gregkh@linuxfoundation.org>
CC: Justin Ernst <justin.ernst@hpe.com>
CC: linux-edac <linux-edac@vger.kernel.org>
CC: Mauro Carvalho Chehab <mchehab@kernel.org>
CC: Russ Anderson <rja@hpe.com>
Cc: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20180926152752.GG5584@zn.tnic
Nobody(*) uses them. Dropping this will allow us to make the total
number of memory controllers configurable (as we won't have to worry
about duplicated device names under this directory).
(*) https://lkml.kernel.org/r/20180927221054.580220e5@coco.lan
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
CC: Aristeu Rozanski Filho <arozansk@redhat.com>
CC: Greg KH <gregkh@linuxfoundation.org>
CC: Justin Ernst <justin.ernst@hpe.com>
CC: Mauro Carvalho Chehab <mchehab@kernel.org>
CC: Russ Anderson <rja@hpe.com>
CC: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20181001224313.GA9487@agluck-desk
It was previously noted that Kconfig complained about unmet dependencies
when trying to configure skx_edac together with CONFIG_ACPI=n. First fix
for this checked for ACPI when doing
select ACPI_ADXL
but this required stub functions for the case where ACPI wasn't
selected. It also allowed building a driver that didn't actually work
for a system that has non-volatile DIMMs.
Arnd Bergmann pointed out that the right fix is to make EDAC_SKX
"depend on ACPI".
Fixes: a324e9396c ("EDAC, skx: Fix randconfig builds")
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
CC: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Mauro Carvalho Chehab <mchehab@kernel.org>
CC: linux-edac <linux-edac@vger.kernel.org>
CC: qiuxu.zhuo@intel.com
Link: http://lkml.kernel.org/r/20181106183914.GA26731@agluck-desk
Fix this gcc -Wunused-but-set-variable warning:
drivers/edac/i82975x_edac.c:378:16: warning: variable 'dtype'
set but not used [-Wunused-but-set-variable]
It was introduced in
084a4fccef ("edac: move dimm properties to struct dimm_info")
but never used.
Also, remove the function i82975x_dram_type() and move the comment and
the assignment to the place where it is used.
[ bp: massage commit message and shorten comment. ]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
CC: "Arvind R." <arvino55@gmail.com>
CC: Mauro Carvalho Chehab <mchehab@kernel.org>
CC: ravi@jetztechnologies.com
CC: arvino55@gmail.com
CC: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20181107022237.14048-1-yuehaibing@huawei.com
irq_handled isn't initialized to false on function entry. However, it is
not really needed and the IRQ handler return value can be set directly
instead.
[ bp: rewrite commit message. ]
Fixes: 27450653f1 ("drivers: edac: Add EDAC driver support for QCOM SoCs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
CC: Channagoud Kadabi <ckadabi@codeaurora.org>
CC: Mauro Carvalho Chehab <mchehab@kernel.org>
CC: Venkata Narendra Kumar Gutta <vnkgutta@codeaurora.org>
CC: kernel-janitors@vger.kernel.org
CC: linux-arm-msm@vger.kernel.org
CC: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20181018141522.rywdvjmlpk4ticiw@kili.mountain
* ACPI_ADXL build fix
-----BEGIN PGP SIGNATURE-----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=JQUK
-----END PGP SIGNATURE-----
Merge tag 'edac_for_4.20_2' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull more EDAC updates from Borislav Petkov:
"The second part of the EDAC pile which contains the ADXL user and a
build fix which addresses a not-so-sensical .config but fixes
randconfig builds people do:
- skx_edac: Address translation for NVDIMMs (Tony Luck and Qiuxu Zhuo)
- ACPI_ADXL build fix"
[ I don't think "sensical" is a word, particularly when used in the
context of actually meaning "nonsensical", but I like it - Linus ]
* tag 'edac_for_4.20_2' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC, skx: Fix randconfig builds
EDAC, skx_edac: Add address translation for non-volatile DIMMs
The driver depends on the ADXL component glue and selects it. However,
ADXL itself implicitly depends on ACPI and in nonsensical randconfig
builds like this:
# CONFIG_ACPI is not set
CONFIG_ACPI_ADXL=y
where ACPI is not enabled, the build fails with:
drivers/edac/skx_edac.o: In function `skx_mce_check_error':
skx_edac.c:(.text+0xab): undefined reference to `adxl_decode'
drivers/edac/skx_edac.o: In function `skx_init':
skx_edac.c:(.init.text+0x8bf): undefined reference to `adxl_get_component_names'
make: *** [vmlinux] Error 1
Add stubs for that case so that the build succeeds. CONFIG_ACPI=n
doesn't make any sense for real configurations but this fix will at
least silence randconfig builds.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Tony Luck <tony.luck@intel.com>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
The most noteworthy SoC driver changes this time include:
- The TEE subsystem gains an in-kernel interface to access the TEE
from device drivers.
- The reset controller subsystem gains a driver for the Qualcomm
Snapdragon 845 Power Domain Controller.
- The Xilinx Zynq platform now has a firmware interface for its
platform management unit. This contains a firmware "ioctl" interface
that was a little controversial at first, but the version we merged
solved that by not exposing arbitrary firmware calls to user space.
- The Amlogic Meson platform gains a "canvas" driver that is used
for video processing and shared between different high-level drivers.
The rest is more of the usual, mostly related to SoC specific power
management support and core drivers in drivers/soc:
- Several Renesas SoCs (RZ/G1N, RZ/G2M, R-Car V3M, RZ/A2M) gain new
features related to power and reset control.
- The Mediatek mt8183 and mt6765 SoC platforms gain support for
their respective power management chips.
- A new driver for NXP i.MX8, which need a firmware interface for
power management.
- The SCPI firmware interface now contains support estimating power
usage of performance states
- The NVIDIA Tegra "pmc" driver gains a few new features, in particular
a pinctrl interface for configuring the pads.
- Lots of small changes for Qualcomm, in particular the "smem"
device driver.
- Some cleanups for the TI OMAP series related to their sysc
controller.
Additional cleanups and bugfixes in SoC specific drivers include the
Meson, Keystone, NXP, AT91, Sunxi, Actions, and Tegra platforms.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=c/PQ
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"The most noteworthy SoC driver changes this time include:
- The TEE subsystem gains an in-kernel interface to access the TEE
from device drivers.
- The reset controller subsystem gains a driver for the Qualcomm
Snapdragon 845 Power Domain Controller.
- The Xilinx Zynq platform now has a firmware interface for its
platform management unit. This contains a firmware "ioctl"
interface that was a little controversial at first, but the version
we merged solved that by not exposing arbitrary firmware calls to
user space.
- The Amlogic Meson platform gains a "canvas" driver that is used for
video processing and shared between different high-level drivers.
The rest is more of the usual, mostly related to SoC specific power
management support and core drivers in drivers/soc:
- Several Renesas SoCs (RZ/G1N, RZ/G2M, R-Car V3M, RZ/A2M) gain new
features related to power and reset control.
- The Mediatek mt8183 and mt6765 SoC platforms gain support for their
respective power management chips.
- A new driver for NXP i.MX8, which need a firmware interface for
power management.
- The SCPI firmware interface now contains support estimating power
usage of performance states
- The NVIDIA Tegra "pmc" driver gains a few new features, in
particular a pinctrl interface for configuring the pads.
- Lots of small changes for Qualcomm, in particular the "smem" device
driver.
- Some cleanups for the TI OMAP series related to their sysc
controller.
Additional cleanups and bugfixes in SoC specific drivers include the
Meson, Keystone, NXP, AT91, Sunxi, Actions, and Tegra platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (129 commits)
firmware: tegra: bpmp: Implement suspend/resume support
drivers: clk: Add ZynqMP clock driver
dt-bindings: clock: Add bindings for ZynqMP clock driver
firmware: xilinx: Add zynqmp IOCTL API for device control
Documentation: xilinx: Add documentation for eemi APIs
MAINTAINERS: imx: include drivers/firmware/imx path
firmware: imx: add misc svc support
firmware: imx: add SCU firmware driver support
reset: Fix potential use-after-free in __of_reset_control_get()
dt-bindings: arm: fsl: add scu binding doc
soc: fsl: qbman: add interrupt coalesce changing APIs
soc: fsl: bman_portals: defer probe after bman's probe
soc: fsl: qbman: Use last response to determine valid bit
soc: fsl: qbman: Add 64 bit DMA addressing requirement to QBMan
soc: fsl: qbman: replace CPU 0 with any online CPU in hotplug handlers
soc: fsl: qbman: Check if CPU is offline when initializing portals
reset: qcom: PDC Global (Power Domain Controller) reset controller
dt-bindings: reset: Add PDC Global binding for SDM845 SoCs
reset: Grammar s/more then once/more than once/
bus: ti-sysc: Just use SET_NOIRQ_SYSTEM_SLEEP_PM_OPS
...
- Sync dtc with upstream version v1.4.7-14-gc86da84d30e4
- Work to get rid of direct accesses to struct device_node name and
type pointers in preparation for removing them. New helpers for
parsing DT cpu nodes and conversions to use the helpers. printk
conversions to %pOFn for printing DT node names. Most went thru
subystem trees, so this is the remainder.
- Fixes to DT child node lookups to actually be restricted to child
nodes instead of treewide.
- Refactoring of dtb targets out of arch code. This makes the support
more uniform and enables building all dtbs on c6x, microblaze, and
powerpc.
- Various DT binding updates for Renesas r8a7744 SoC
- Vendor prefixes for Facebook, OLPC
- Restructuring of some ARM binding docs moving some peripheral bindings
out of board/SoC binding files
- New "secure-chosen" binding for secure world settings on ARM
- Dual licensing of 2 DT IRQ binding headers
-----BEGIN PGP SIGNATURE-----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=335v
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
"A bit bigger than normal as I've been busy this cycle.
There's a few things with dependencies and a few things subsystem
maintainers didn't pick up, so I'm taking them thru my tree.
The fixes from Johan didn't get into linux-next, but they've been
waiting for some time now and they are what's left of what subsystem
maintainers didn't pick up.
Summary:
- Sync dtc with upstream version v1.4.7-14-gc86da84d30e4
- Work to get rid of direct accesses to struct device_node name and
type pointers in preparation for removing them. New helpers for
parsing DT cpu nodes and conversions to use the helpers. printk
conversions to %pOFn for printing DT node names. Most went thru
subystem trees, so this is the remainder.
- Fixes to DT child node lookups to actually be restricted to child
nodes instead of treewide.
- Refactoring of dtb targets out of arch code. This makes the support
more uniform and enables building all dtbs on c6x, microblaze, and
powerpc.
- Various DT binding updates for Renesas r8a7744 SoC
- Vendor prefixes for Facebook, OLPC
- Restructuring of some ARM binding docs moving some peripheral
bindings out of board/SoC binding files
- New "secure-chosen" binding for secure world settings on ARM
- Dual licensing of 2 DT IRQ binding headers"
* tag 'devicetree-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (78 commits)
ARM: dt: relicense two DT binding IRQ headers
power: supply: twl4030-charger: fix OF sibling-node lookup
NFC: nfcmrvl_uart: fix OF child-node lookup
net: stmmac: dwmac-sun8i: fix OF child-node lookup
net: bcmgenet: fix OF child-node lookup
drm/msm: fix OF child-node lookup
drm/mediatek: fix OF sibling-node lookup
of: Add missing exports of node name compare functions
dt-bindings: Add OLPC vendor prefix
dt-bindings: misc: bk4: Add device tree binding for Liebherr's BK4 SPI bus
dt-bindings: thermal: samsung: Add SPDX license identifier
dt-bindings: clock: samsung: Add SPDX license identifiers
dt-bindings: timer: ostm: Add R7S9210 support
dt-bindings: phy: rcar-gen2: Add r8a7744 support
dt-bindings: can: rcar_can: Add r8a7744 support
dt-bindings: timer: renesas, cmt: Document r8a7744 CMT support
dt-bindings: watchdog: renesas-wdt: Document r8a7744 support
dt-bindings: thermal: rcar: Add device tree support for r8a7744
Documentation: dt: Add binding for /secure-chosen/stdout-path
dt-bindings: arm: zte: Move sysctrl bindings to their own doc
...
Currently, this driver doesn't support address translation for
non-volatile DIMMs.
The ACPI ADXL DSM method provides address translation for both volatile
and non-volatile DIMMs. Enable it to use the ACPI DSM methods if they
are supported and there are non-volatile DIMMs populated on the system.
Co-developed-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
CC: Mauro Carvalho Chehab <mchehab@kernel.org>
CC: arozansk@redhat.com
CC: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1540106336-5212-1-git-send-email-qiuxu.zhuo@intel.com
Hygon Dhyana support (Pu Wen)
- sb_edac: New maintainer + fixes (Tony Luck)
Error reporting improvements and fixes (Qiuxu Zhuo)
- ghes_edac: SMBIOS handle type 17 for DIMM locating and per-DIMM error
accounting (Fan Wu)
- altera_edac: Stratix10 support and refactoring (Thor Thayer)
Out of tree addition:
- acpi_adxl: Address Translation interface using an ACPI DSM (Tony Luck)
- the usual amount of other misc fixes and cleanups all over.
-----BEGIN PGP SIGNATURE-----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=HEJK
-----END PGP SIGNATURE-----
Merge tag 'edac_for_4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC updates from Borislav Petkov:
"The EDAC tree was busier than usual this cycle as the shortlog below
shows.
Also, this pull request is carrying an ACPI DSM driver which is used
to ask the platform to supply the DIMM location of a reported hardware
error and thus simplify all the EDAC logic when trying to map the
error address to the respective DIMM.
Core EDAC updates:
- amd64_edac: AMD family 0x17, models 0x10-0x2f support (Michael Jin)
Hygon Dhyana support (Pu Wen)
- sb_edac: New maintainer + fixes (Tony Luck) Error reporting
improvements and fixes (Qiuxu Zhuo)
- ghes_edac: SMBIOS handle type 17 for DIMM locating and per-DIMM
error accounting (Fan Wu)
- altera_edac: Stratix10 support and refactoring (Thor Thayer)
Out of tree addition:
- acpi_adxl: Address Translation interface using an ACPI DSM (Tony
Luck)
- the usual amount of other misc fixes and cleanups all over"
* tag 'edac_for_4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp: (22 commits)
ACPI/ADXL: Add address translation interface using an ACPI DSM
EDAC, thunderx: Fix memory leak in thunderx_l2c_threaded_isr()
EDAC, skx_edac: Fix logical channel intermediate decoding
EDAC, {i7core,sb,skx}_edac: Fix uncorrected error counting
EDAC, altera: Work around int-to-pointer-cast warnings
EDAC, amd64: Add Hygon Dhyana support
EDAC: Raise the maximum number of memory controllers
arm64: dts: stratix10: Add peripheral EDAC nodes
EDAC, altera: Add Stratix10 peripheral support
EDAC, altera: Merge Stratix10 into the Arria10 SDRAM probe routine
arm64: dts: stratix10: Add SDRAM node
EDAC, altera: Combine Stratix10 and Arria10 probe functions
arm64: dts: stratix10: Additions to EDAC System Manager
EDAC, i7core: Remove set but not used variable pvt
EDAC, ghes: Use CPER module handles to locate DIMMs
EDAC: Correct DIMM capacity unit symbol
EDAC, sb_edac: Fix signedness bugs in *_get_ha() functions
EDAC, sb_edac: Fix reporting for patrol scrubber errors
EDAC, sb_edac: Return early on ADDRV bit and address type test
MAINTAINERS: Update maintainer for drivers/edac/sb_edac.c
...
Pull perf updates from Ingo Molnar:
"The main updates in this cycle were:
- Lots of perf tooling changes too voluminous to list (big perf trace
and perf stat improvements, lots of libtraceevent reorganization,
etc.), so I'll list the authors and refer to the changelog for
details:
Benjamin Peterson, Jérémie Galarneau, Kim Phillips, Peter
Zijlstra, Ravi Bangoria, Sangwon Hong, Sean V Kelley, Steven
Rostedt, Thomas Gleixner, Ding Xiang, Eduardo Habkost, Thomas
Richter, Andi Kleen, Sanskriti Sharma, Adrian Hunter, Tzvetomir
Stoyanov, Arnaldo Carvalho de Melo, Jiri Olsa.
... with the bulk of the changes written by Jiri Olsa, Tzvetomir
Stoyanov and Arnaldo Carvalho de Melo.
- Continued intel_rdt work with a focus on playing well with perf
events. This also imported some non-perf RDT work due to
dependencies. (Reinette Chatre)
- Implement counter freezing for Arch Perfmon v4 (Skylake and newer).
This allows to speed up the PMI handler by avoiding unnecessary MSR
writes and make it more accurate. (Andi Kleen)
- kprobes cleanups and simplification (Masami Hiramatsu)
- Intel Goldmont PMU updates (Kan Liang)
- ... plus misc other fixes and updates"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (155 commits)
kprobes/x86: Use preempt_enable() in optimized_callback()
x86/intel_rdt: Prevent pseudo-locking from using stale pointers
kprobes, x86/ptrace.h: Make regs_get_kernel_stack_nth() not fault on bad stack
perf/x86/intel: Export mem events only if there's PEBS support
x86/cpu: Drop pointless static qualifier in punit_dev_state_show()
x86/intel_rdt: Fix initial allocation to consider CDP
x86/intel_rdt: CBM overlap should also check for overlap with CDP peer
x86/intel_rdt: Introduce utility to obtain CDP peer
tools lib traceevent, perf tools: Move struct tep_handler definition in a local header file
tools lib traceevent: Separate out tep_strerror() for strerror_r() issues
perf python: More portable way to make CFLAGS work with clang
perf python: Make clang_has_option() work on Python 3
perf tools: Free temporary 'sys' string in read_event_files()
perf tools: Avoid double free in read_event_file()
perf tools: Free 'printk' string in parse_ftrace_printk()
perf tools: Cleanup trace-event-info 'tdata' leak
perf strbuf: Match va_{add,copy} with va_end
perf test: S390 does not support watchpoints in test 22
perf auxtrace: Include missing asm/bitsperlong.h to get BITS_PER_LONG
tools include: Adopt linux/bits.h
...
Going primarily by:
https://en.wikipedia.org/wiki/List_of_Intel_Atom_microprocessors
with additional information gleaned from other related pages; notably:
- Bonnell shrink was called Saltwell
- Moorefield is the Merriefield refresh which makes it Airmont
The general naming scheme is: FAM6_ATOM_UARCH_SOCTYPE
for i in `git grep -l FAM6_ATOM` ; do
sed -i -e 's/ATOM_PINEVIEW/ATOM_BONNELL/g' \
-e 's/ATOM_LINCROFT/ATOM_BONNELL_MID/' \
-e 's/ATOM_PENWELL/ATOM_SALTWELL_MID/g' \
-e 's/ATOM_CLOVERVIEW/ATOM_SALTWELL_TABLET/g' \
-e 's/ATOM_CEDARVIEW/ATOM_SALTWELL/g' \
-e 's/ATOM_SILVERMONT1/ATOM_SILVERMONT/g' \
-e 's/ATOM_SILVERMONT2/ATOM_SILVERMONT_X/g' \
-e 's/ATOM_MERRIFIELD/ATOM_SILVERMONT_MID/g' \
-e 's/ATOM_MOOREFIELD/ATOM_AIRMONT_MID/g' \
-e 's/ATOM_DENVERTON/ATOM_GOLDMONT_X/g' \
-e 's/ATOM_GEMINI_LAKE/ATOM_GOLDMONT_PLUS/g' ${i}
done
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: dave.hansen@linux.intel.com
Cc: len.brown@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The count of errors is picked up from bits 52:38 of the machine check
bank status register. But this is the count of *corrected* errors. If an
uncorrected error is being logged, the h/w sets this field to 0. Which
means that when edac_mc_handle_error() is called, the EDAC core will
carefully add zero to the appropriate uncorrected error counts.
Signed-off-by: Tony Luck <tony.luck@intel.com>
[ Massage commit message. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Cc: Aristeu Rozanski <aris@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20180928213934.19890-1-tony.luck@intel.com
Use the for_each_of_cpu_node iterator to iterate over cpu nodes. This
has the side effect of defaulting to iterating using "cpu" node names in
preference to the deprecated (for FDT) device_type == "cpu".
The error messages are removed in the process as it's not the driver's
job to be checking cpu nodes. Any problems with cpu nodes should be
noticed by the architecture code.
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac@vger.kernel.org
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rob Herring <robh@kernel.org>
The altera edac driver passes a token from a DT resource as
resource_size_t into an SMC call, but casts it to an __iomem pointer and
then a plain void pointer inbetween, mixing three or four incompatible
types in the process. The compiler complains about one of the
conversions:
drivers/edac/altera_edac.c: In function 'altr_init_a10_ecc_block':
drivers/edac/altera_edac.c:1053:10: error: cast to pointer from integer of \
different size [-Werror=int-to-pointer-cast]
base = (void __iomem *)res.start;
^
drivers/edac/altera_edac.c: In function 'altr_edac_a10_probe':
drivers/edac/altera_edac.c:2062:10: error: cast to pointer from integer of \
different size [-Werror=int-to-pointer-cast]
base = (void __iomem *)res.start;
Using a static checker probably also notices the __iomem cast. Solving
this properly isn't trivial, but simply casting to a 'uintptr_t' instead
of 'void __iomem *' makes it less wrong and should avoid the warnings.
Fixes: d5fc912556 ("EDAC, altera: Combine Stratix10 and Arria10 probe functions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Thor Thayer <thor.thayer@linux.intel.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: David Frey <dpfrey@gmail.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: linux-edac@vger.kernel.org
Link: https://lkml.kernel.org/r/20180927100949.973078-1-arnd@arndb.de
Remove the unused local variable pvt:
drivers/edac/i7core_edac.c: In function 'i7core_mce_check_error':
drivers/edac/i7core_edac.c:1818:21: warning: variable 'pvt' set but not used \
[-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1537841043-108267-1-git-send-email-yuehaibing@huawei.com
The {i3200|i7core|sb|skx}_edac drivers show DIMM capacity using the
wrong unit symbol: 'Mb' - megabit. Fix them by replacing 'Mb' with
'MiB' - mebibyte.
[Tony: These are all "edac_dbg()" messages, so this won't break scripts
that parse console logs.]
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Aristeu Rozanski <aris@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac@vger.kernel.org
Link: https://lkml.kernel.org/r/20180919003433.16475-1-tony.luck@intel.com
A static checker gave the following warnings:
drivers/edac/sb_edac.c:1030 ibridge_get_ha() warn: signedness bug returning '(-22)'
drivers/edac/sb_edac.c:1037 knl_get_ha() warn: signedness bug returning '(-22)'
Both because the functions are declared to return a "u8", but try to
return -EINVAL for the error case.
Fix by returning 0xff (since the caller doesn't look at, or pass on, the
return value).
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20180914201905.GA30946@agluck-desk
Signed-off-by: Borislav Petkov <bp@suse.de>
Add error reporting driver for Single Bit Errors (SBEs) and Double Bit
Errors (DBEs). As of now, this driver supports error reporting for
Last Level Cache Controller (LLCC) of Tag RAM and Data RAM. Interrupts
are triggered when the errors happen in the cache, the driver handles
those interrupts and dumps the syndrome registers.
Signed-off-by: Channagoud Kadabi <ckadabi@codeaurora.org>
Signed-off-by: Venkata Narendra Kumar Gutta <vnkgutta@codeaurora.org>
Co-developed-by: Venkata Narendra Kumar Gutta <vnkgutta@codeaurora.org>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
sb_edac sometimes reports the wrong DIMM for a memory error found by
the patrol scrubber. That is because the hardware provides only a 4KB
page-aligned address for the error case.
This means that the EDAC driver will point at the DIMM matching offset
0x0 in the 4KB page, but because of interleaving across channels and
ranks, the actual DIMM involved may be different if the error is on some
other cache line within the page.
Therefore, reconstruct the socket/iMC/channel information from the "mce"
structure passed to the EDAC driver. The DIMM cannot be determined, so
pass "dimm=-1" to the EDAC core. It will report that all the DIMMs on
that channel may be affected.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: Aristeu Rozanski <aris@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20180907230828.13901-3-tony.luck@intel.com
[ Improve comments on the functions to convert bank number
to memory controller number. Minor cleanup to commit message. ]
Signed-off-by: Tony Luck <tony.luck@intel.com>
[ Massage commit message more. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Users of the mce_register_decode_chain() are called for every logged
error. EDAC drivers should check:
1) Is this a memory error? [bit 7 in status register]
2) Is there a valid address? [bit 58 in status register]
3) Is the address a system address? [bitfield 8:6 in misc register]
The sb_edac driver performed test "1" twice. Waited far too long to
perform check "2". Didn't do check "3" at all.
Fix it by moving the test for valid address from
sbridge_mce_output_error() into sbridge_mce_check_error() and add a test
for the type immediately after. Delete the redundant check for the type
of the error from sbridge_mce_output_error().
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: Aristeu Rozanski <aris@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20180907230828.13901-2-tony.luck@intel.com
[ Re-word commit message. ]
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Split regmap_config.use_single_rw into use_single_read and
use_single_write. This change enables drivers of devices which only
support bulk operations in one direction to use the regmap_bulk_*()
functions for both directions and have their bulk operation split into
single operations only when necessary.
Update all struct regmap_config instances where use_single_rw==true to
instead set both use_single_read and use_single_write. No attempt was
made to evaluate whether it is possible to set only one of
use_single_read or use_single_write.
Signed-off-by: David Frey <dpfrey@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add new device IDs for family 17h, models 10h-2fh.
This is required by amd64_edac_mod in order to properly detect PCI
device functions 0 and 6.
Signed-off-by: Michael Jin <mikhail.jin@gmail.com>
Reviewed-by: Yazen Ghannam <Yazen.Ghannam@amd.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20180816192840.31166-1-mikhail.jin@gmail.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Extend the driver to check whether segment number and bus number matches
when deciding how to group memory controller PCI devices to CPU sockets.
Signed-off-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20180724190213.26359-1-msys.mizuma@gmail.com
[ Cleanup commit message. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
In the quest to remove all stack VLA usage from the kernel[1], switch to
using a kmalloc-allocated buffer instead of stack space. This should be
fine since the existing routine is allocating memory too.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Jan Glauber <jglauber@cavium.com>
Cc: David Daney <david.daney@cavium.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20180629184850.GA37464@beast
Link: https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com [1]
Signed-off-by: Borislav Petkov <bp@suse.de>
Make sure to free and deregister the addrmatch and chancounts devices
allocated during probe in all error paths. Also fix use-after-free in a
probe error path and in the remove success path where the devices were
being put before before deregistration.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Fixes: 356f0a3086 ("i7core_edac: change the mem allocation scheme to make Documentation/kobject.txt happy")
Link: http://lkml.kernel.org/r/20180612124335.6420-2-johan@kernel.org
Signed-off-by: Borislav Petkov <bp@suse.de>
Make sure to use put_device() to free the initialised struct device so
that resources managed by driver core also gets released in the event of
a registration failure.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Denis Kirjanov <kirjanov@gmail.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Fixes: 2d56b109e3 ("EDAC: Handle error path in edac_mc_sysfs_init() properly")
Link: http://lkml.kernel.org/r/20180612124335.6420-1-johan@kernel.org
Signed-off-by: Borislav Petkov <bp@suse.de>
If regmap_write() fails, we should release some resources as done in all
the other error handling paths of the function.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Thor Thayer <thor.thayer@linux.intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20180610174532.22071-1-christophe.jaillet@wanadoo.fr
Fixes: e9918d7faf ("EDAC, altera: Handle SDRAM Uncorrectable Errors on Stratix10")
Signed-off-by: Borislav Petkov <bp@suse.de>
ARM machines all have DMI tables so if they request hw error reporting
through GHES, then the driver should be able to detect DIMMs and report
errors successfully (famous last words :)).
Make the platform-based list x86-specific so that ghes_edac can load on
ARM.
Reported-by: Qiang Zheng <zhengqiang10@huawei.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: James Morse <james.morse@arm.com>
Tested-by: James Morse <james.morse@arm.com>
Tested-by: Qiang Zheng <zhengqiang10@huawei.com>
Link: https://lkml.kernel.org/r/1526039543-180996-1-git-send-email-zhengqiang10@huawei.com
The kbuild test robot reported the following warning:
drivers/edac/altera_edac.c: In function 'ocram_free_mem':
drivers/edac/altera_edac.c:1410:42: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
gen_pool_free((struct gen_pool *)other, (u32)p, size);
^
After adding support for ARM64 architectures, the unsigned long
parameter is 64 bits and causes a build warning on 64-bit configs. Fix
by casting to the correct size (unsigned long) instead of u32.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-edac <linux-edac@vger.kernel.org>
Fixes: c3eea1942a ("EDAC, altera: Add Altera L2 cache and OCRAM support")
Link: http://lkml.kernel.org/r/1526317441-4996-1-git-send-email-thor.thayer@linux.intel.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Prevent build error when CONFIG_ACPI_NFIT=m and CONFIG_EDAC_SKX=y by
limiting EDAC_SKX based on how ACPI_NFIT is set.
Fixes this build error:
drivers/edac/skx_edac.o: In function `get_nvdimm_info':
../drivers/edac/skx_edac.c:399: undefined reference to `nfit_get_smbios_id'
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Fixes: 58ca9ac146 ("EDAC, skx_edac: Detect non-volatile DIMMs")
Link: http://lkml.kernel.org/r/3af91354-8e19-d2af-1bba-ced8dce053f1@infradead.org
Signed-off-by: Borislav Petkov <bp@suse.de>
... for improved readability. Also, add a local mask variable for the
same reason.
No functional changes.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
The ghes_edac driver obtains memory type from SMBIOS type 17, but it
does not recognize DDR4 and NVDIMM types.
Add support of DDR4 and NVDIMM types. NVDIMM type is denoted by memory
type DDR3/4 and non-volatile.
Reported-by: Robert Elliott <elliott@hpe.com>
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20180509222030.9299-1-toshi.kani@hpe.com
Signed-off-by: Borislav Petkov <bp@suse.de>
On Stratix10, uncorrectable errors are routed to the SError exception
instead of the IRQ exceptions. In Stratix10, uncorrectable SErrors
must be treated as fatal and will cause a panic. Older Altera/Intel
parts printed out a message for UE so do that here using the notifier
framework.
Record the UE in sticky registers that retain the state through a reset.
Check these registers on probe and printout the error on startup.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: mark.rutland@arm.com
Cc: mchehab@kernel.org
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1526079610-5527-1-git-send-email-thor.thayer@linux.intel.com
[ Remove unused var in s10_edac_dberr_handler(), reorder args. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
The use of the @ghes argument was removed in a previous commit, but
function signature was not updated to reflect this.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Acked-by: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: linux-acpi@vger.kernel.org
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20180430213358.8319-1-mr.nuke.me@gmail.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Add a null check for ghes_pvt, before dereferencing it. The pointer
could still be null in case the return path is taken before initialising
ghes_pvt in the registration function.
Reviewed-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Sughosh Ganu <sughosh.ganu@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: lkml <linux-kernel@vger.kernel.org>
Link: http://lkml.kernel.org/r/1524737809-24475-1-git-send-email-sughosh.ganu@arm.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Tony reported seeing
"Internal error: Can't find EDAC structure"
when injecting correctable errors due to the fact that ghes_edac would
still load even if the whitelist won't hit. Drop the pr_err() in
ghes_edac_report_mem_error() for now due to the hacky way how ghes_edac
depends on ghes.c.
While at it, make ghes_edac_register() return an error if it doesn't hit
in the whitelist as it is the only sensible thing to do in that
situation.
Furthermore, move the call to it to happen last in ghes_probe() so that
GHES initializing properly does not depend on ghes_edac init at all
as latter is only reporting errors and not required for GHES's proper
functioning.
Reviewed-by: Toshi Kani <toshi.kani@hpe.com>
Tested-by: Sughosh Ganu <sughosh.ganu@arm.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20180420182015.zao3olss4tvvlxki@agluck-desk
* misc fixes
-----BEGIN PGP SIGNATURE-----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=K89j
-----END PGP SIGNATURE-----
Merge tag 'edac_for_4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC updates from Borislav Petkov:
"Noteworthy is the NVDIMM support:
- NVDIMM support to EDAC (Tony Luck)
- misc fixes"
* tag 'edac_for_4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC, sb_edac: Remove variable length array usage
EDAC, skx_edac: Detect non-volatile DIMMs
firmware, DMI: Add function to look up a handle and return DIMM size
acpi, nfit: Add function to look up nvdimm device and provide SMBIOS handle
EDAC: Add new memory type for non-volatile DIMMs
EDAC: Drop duplicated array of strings for memory type names
EDAC, layerscape: Allow building for LS1021A
This removes the entire architecture code for blackfin, cris, frv, m32r,
metag, mn10300, score, and tile, including the associated device drivers.
I have been working with the (former) maintainers for each one to ensure
that my interpretation was right and the code is definitely unused in
mainline kernels. Many had fond memories of working on the respective
ports to start with and getting them included in upstream, but also saw
no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company
in charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It seems
that all the SoC product lines are still around, but have not used the
custom CPU architectures for several years at this point. In contrast,
CPU instruction sets that remain popular and have actively maintained
kernel ports tend to all be used across multiple licensees.
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I made
sure that they are all unused. Some architectures (notably tile, mn10300,
and blackfin) are still being shipped in products with old kernels,
but those products will never be updated to newer kernel releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing their
support or getting it added to mainline gcc in the first place.
They all have patched gcc-7.3 ports that work to some degree, but
complete upstream support won't happen before gcc-8.1. Csky posted
their first kernel patch set last week, their situation will be similar.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fQ8z
-----END PGP SIGNATURE-----
Merge tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pul removal of obsolete architecture ports from Arnd Bergmann:
"This removes the entire architecture code for blackfin, cris, frv,
m32r, metag, mn10300, score, and tile, including the associated device
drivers.
I have been working with the (former) maintainers for each one to
ensure that my interpretation was right and the code is definitely
unused in mainline kernels. Many had fond memories of working on the
respective ports to start with and getting them included in upstream,
but also saw no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company in
charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It
seems that all the SoC product lines are still around, but have not
used the custom CPU architectures for several years at this point. In
contrast, CPU instruction sets that remain popular and have actively
maintained kernel ports tend to all be used across multiple licensees.
[ See the new nds32 port merged in the previous commit for the next
generation of "one company in charge of an SoC line, a CPU
microarchitecture and a software ecosystem" - Linus ]
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I
made sure that they are all unused. Some architectures (notably tile,
mn10300, and blackfin) are still being shipped in products with old
kernels, but those products will never be updated to newer kernel
releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing
their support or getting it added to mainline gcc in the first
place. They all have patched gcc-7.3 ports that work to some
degree, but complete upstream support won't happen before gcc-8.1.
Csky posted their first kernel patch set last week, their situation
will be similar
[ Palmer Dabbelt points out that RISC-V support is in mainline gcc
since gcc-7, although gcc-7.3.0 is the recommended minimum - Linus ]"
This really says it all:
2498 files changed, 95 insertions(+), 467668 deletions(-)
* tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (74 commits)
MAINTAINERS: UNICORE32: Change email account
staging: iio: remove iio-trig-bfin-timer driver
tty: hvc: remove tile driver
tty: remove bfin_jtag_comm and hvc_bfin_jtag drivers
serial: remove tile uart driver
serial: remove m32r_sio driver
serial: remove blackfin drivers
serial: remove cris/etrax uart drivers
usb: Remove Blackfin references in USB support
usb: isp1362: remove blackfin arch glue
usb: musb: remove blackfin port
usb: host: remove tilegx platform glue
pwm: remove pwm-bfin driver
i2c: remove bfin-twi driver
spi: remove blackfin related host drivers
watchdog: remove bfin_wdt driver
can: remove bfin_can driver
mmc: remove bfin_sdh driver
input: misc: remove blackfin rotary driver
input: keyboard: remove bf54x driver
...
The Tile architecture is obsolete and getting removed from the kernel,
this driver appears to only be used there, and not on the ARM based
successors (Tile-Mx, BlueField), so we should remove it as well.
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In preparation for enabling -Wvla, remove VLA and replace it with a
fixed-length array instead.
Also, remove max_interleave as it is no longer needed.
Reviewed-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20180314182131.GA25259@embeddedgus
Signed-off-by: Borislav Petkov <bp@suse.de>
This just covers the topology function of the EDAC driver. We locate
which DIMM slots are populated with NVDIMMs and query the NFIT and
SMBIOS tables to get the size.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: Aristeu Rozanski <aris@redhat.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: linux-acpi@vger.kernel.org
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: linux-nvdimm@lists.01.org
Link: http://lkml.kernel.org/r/20180312182430.10335-6-tony.luck@intel.com
Signed-off-by: Borislav Petkov <bp@suse.de>
There are now non-volatile versions of DIMMs. Add a new entry to "enum
mem_type" and a new string in edac_mem_types[].
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Aristeu Rozanski <aris@redhat.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: linux-acpi@vger.kernel.org
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: linux-nvdimm@lists.01.org
Link: http://lkml.kernel.org/r/20180312182430.10335-3-tony.luck@intel.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Somehow we ended up with two separate arrays of strings to describe the
"enum mem_type" values.
In edac_mc.c we have an exported list edac_mem_types[] that is used
by a couple of drivers in debug messaged.
In edac_mc_sysfs.c we have a private list that is used to display
values in:
/sys/devices/system/edac/mc/mc*/dimm*/dimm_mem_type
/sys/devices/system/edac/mc/mc*/csrow*/mem_type
This list was missing a value for MEM_LRDDR3.
The string values in the two lists were different :-(
Combining the lists, I kept the values so that the sysfs output
will be unchanged as some scripts may depend on that.
Reported-by: Borislav Petkov <bp@suse.de>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Aristeu Rozanski <aris@redhat.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: linux-acpi@vger.kernel.org
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: linux-nvdimm@lists.01.org
Link: http://lkml.kernel.org/r/20180312182430.10335-2-tony.luck@intel.com
Signed-off-by: Borislav Petkov <bp@suse.de>
The LS1021A has a memory controller supported by this driver. It builds
just fine, and I've done some rudimentary testing using the error
injection facility, which suggests that it is indeed working.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Acked-by: York Sun <york.sun@nxp.com>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20180220150912.2954-1-rasmus.villemoes@prevas.dk
Signed-off-by: Borislav Petkov <bp@suse.de>
Commit
3286d3eb90 ("EDAC, sb_edac: Drop NUM_CHANNELS from 8 back to 4")
decreased NUM_CHANNELS from 8 to 4, but this is not enough for Knights
Landing which supports up to 6 channels.
This caused out-of-bounds writes to pvt->mirror_mode and pvt->tolm
variables which don't pay critical role on KNL code path, so the memory
corruption wasn't causing any visible driver failures.
The easiest way of fixing it is to change NUM_CHANNELS to 6. Do that.
An alternative solution would be to restructure the KNL part of the
driver to 2MC/3channel representation.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Anna Karbownik <anna.karbownik@intel.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: jim.m.snow@intel.com
Cc: krzysztof.paliswiat@intel.com
Cc: lukasz.odzioba@intel.com
Cc: qiuxu.zhuo@intel.com
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: <stable@vger.kernel.org>
Fixes: 3286d3eb90 ("EDAC, sb_edac: Drop NUM_CHANNELS from 8 back to 4")
Link: http://lkml.kernel.org/r/1519312693-4789-1-git-send-email-anna.karbownik@intel.com
[ Massage commit message. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Currently, bank 4 is reserved on Fam17h, so we chose not to initialize
bank 4 in the smca_banks array. This means that when we check if a bank
is initialized, like during boot or resume, we will see that bank 4 is
not initialized and try to initialize it.
This will cause a call trace, when resuming from suspend, due to
rdmsr_*on_cpu() calls in the init path. The rdmsr_*on_cpu() calls issue
an IPI but we're running with interrupts disabled. This triggers:
WARNING: CPU: 0 PID: 11523 at kernel/smp.c:291 smp_call_function_single+0xdc/0xe0
...
Reserved banks will be read-as-zero, so their MCA_IPID register will be
zero. So, like the smca_banks array, the threshold_banks array will not
have an entry for a reserved bank since all its MCA_MISC* registers will
be zero.
Enumerate a "Reserved" bank type that matches on a HWID_MCATYPE of 0,0.
Use the "Reserved" type when checking if a bank is reserved. It's
possible that other bank numbers may be reserved on future systems.
Don't try to find the block address on reserved banks.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org> # 4.14.x
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20180221101900.10326-7-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull x86 PTI and Spectre related fixes and updates from Ingo Molnar:
"Here's the latest set of Spectre and PTI related fixes and updates:
Spectre:
- Add entry code register clearing to reduce the Spectre attack
surface
- Update the Spectre microcode blacklist
- Inline the KVM Spectre helpers to get close to v4.14 performance
again.
- Fix indirect_branch_prediction_barrier()
- Fix/improve Spectre related kernel messages
- Fix array_index_nospec_mask() asm constraint
- KVM: fix two MSR handling bugs
PTI:
- Fix a paranoid entry PTI CR3 handling bug
- Fix comments
objtool:
- Fix paranoid_entry() frame pointer warning
- Annotate WARN()-related UD2 as reachable
- Various fixes
- Add Add Peter Zijlstra as objtool co-maintainer
Misc:
- Various x86 entry code self-test fixes
- Improve/simplify entry code stack frame generation and handling
after recent heavy-handed PTI and Spectre changes. (There's two
more WIP improvements expected here.)
- Type fix for cache entries
There's also some low risk non-fix changes I've included in this
branch to reduce backporting conflicts:
- rename a confusing x86_cpu field name
- de-obfuscate the naming of single-TLB flushing primitives"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (41 commits)
x86/entry/64: Fix CR3 restore in paranoid_exit()
x86/cpu: Change type of x86_cache_size variable to unsigned int
x86/spectre: Fix an error message
x86/cpu: Rename cpu_data.x86_mask to cpu_data.x86_stepping
selftests/x86/mpx: Fix incorrect bounds with old _sigfault
x86/mm: Rename flush_tlb_single() and flush_tlb_one() to __flush_tlb_one_[user|kernel]()
x86/speculation: Add <asm/msr-index.h> dependency
nospec: Move array_index_nospec() parameter checking into separate macro
x86/speculation: Fix up array_index_nospec_mask() asm constraint
x86/debug: Use UD2 for WARN()
x86/debug, objtool: Annotate WARN()-related UD2 as reachable
objtool: Fix segfault in ignore_unreachable_insn()
selftests/x86: Disable tests requiring 32-bit support on pure 64-bit systems
selftests/x86: Do not rely on "int $0x80" in single_step_syscall.c
selftests/x86: Do not rely on "int $0x80" in test_mremap_vdso.c
selftests/x86: Fix build bug caused by the 5lvl test which has been moved to the VM directory
selftests/x86/pkeys: Remove unused functions
selftests/x86: Clean up and document sscanf() usage
selftests/x86: Fix vDSO selftest segfault for vsyscall=none
x86/entry/64: Remove the unused 'icebp' macro
...
x86_mask is a confusing name which is hard to associate with the
processor's stepping.
Additionally, correct an indent issue in lib/cpu.c.
Signed-off-by: Jia Zhang <qianyue.zj@alibaba-inc.com>
[ Updated it to more recent kernels. ]
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: bp@alien8.de
Cc: tony.luck@intel.com
Link: http://lkml.kernel.org/r/1514771530-70829-1-git-send-email-qianyue.zj@alibaba-inc.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We should not call edac_mc_del_mc() if a corresponding call to
edac_mc_add_mc() has not been performed yet.
So here, we should go to err instead of err2 to branch at the right
place of the error handling path.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20180107205400.14068-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Borislav Petkov <bp@suse.de>
TI Keystone and DRA7xx SoCs have support for EDAC on DDR3 memory that can
correct one bit errors and detect two bit errors. Add EDAC driver for this
feature which plugs into the generic kernel EDAC framework.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: linux-omap@vger.kernel.org
Link: http://lkml.kernel.org/r/1510578490-14510-1-git-send-email-t-kristo@ti.com
[ Add SPDX tag and make _emif_get_id() use edac_printk(). ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Fix an uninitialized variable warning in the Octeon EDAC driver, as seen
in MIPS cavium_octeon_defconfig builds since v4.14 with Codescape GNU
Tools 2016.05-03:
drivers/edac/octeon_edac-lmc.c In function ‘octeon_lmc_edac_poll_o2’:
drivers/edac/octeon_edac-lmc.c:87:24: warning: ‘((long unsigned int*)&int_reg)[1]’ may \
be used uninitialized in this function [-Wmaybe-uninitialized]
if (int_reg.s.sec_err || int_reg.s.ded_err) {
^
Iinitialise the whole int_reg variable to zero before the conditional
assignments in the error injection case.
Signed-off-by: James Hogan <jhogan@kernel.org>
Acked-by: David Daney <david.daney@cavium.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 3.15+
Fixes: 1bc021e815 ("EDAC: Octeon: Add error injection support")
Link: http://lkml.kernel.org/r/20171113161206.20990-1-james.hogan@mips.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Summary of modules changes for the 4.15 merge window:
- Treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- Minor code cleanups
Signed-off-by: Jessica Yu <jeyu@kernel.org>
-----BEGIN PGP SIGNATURE-----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=c8vb
-----END PGP SIGNATURE-----
Merge tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux
Pull module updates from Jessica Yu:
"Summary of modules changes for the 4.15 merge window:
- treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- minor code cleanups"
* tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
module: Do not paper over type mismatches in module_param_call()
treewide: Fix function prototypes for module_param_call()
module: Prepare to convert all module_param_call() prototypes
kernel/module: Delete an error message for a failed memory allocation in add_module_usage()
Pull core locking updates from Ingo Molnar:
"The main changes in this cycle are:
- Another attempt at enabling cross-release lockdep dependency
tracking (automatically part of CONFIG_PROVE_LOCKING=y), this time
with better performance and fewer false positives. (Byungchul Park)
- Introduce lockdep_assert_irqs_enabled()/disabled() and convert
open-coded equivalents to lockdep variants. (Frederic Weisbecker)
- Add down_read_killable() and use it in the VFS's iterate_dir()
method. (Kirill Tkhai)
- Convert remaining uses of ACCESS_ONCE() to
READ_ONCE()/WRITE_ONCE(). Most of the conversion was Coccinelle
driven. (Mark Rutland, Paul E. McKenney)
- Get rid of lockless_dereference(), by strengthening Alpha atomics,
strengthening READ_ONCE() with smp_read_barrier_depends() and thus
being able to convert users of lockless_dereference() to
READ_ONCE(). (Will Deacon)
- Various micro-optimizations:
- better PV qspinlocks (Waiman Long),
- better x86 barriers (Michael S. Tsirkin)
- better x86 refcounts (Kees Cook)
- ... plus other fixes and enhancements. (Borislav Petkov, Juergen
Gross, Miguel Bernal Marin)"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
locking/x86: Use LOCK ADD for smp_mb() instead of MFENCE
rcu: Use lockdep to assert IRQs are disabled/enabled
netpoll: Use lockdep to assert IRQs are disabled/enabled
timers/posix-cpu-timers: Use lockdep to assert IRQs are disabled/enabled
sched/clock, sched/cputime: Use lockdep to assert IRQs are disabled/enabled
irq_work: Use lockdep to assert IRQs are disabled/enabled
irq/timings: Use lockdep to assert IRQs are disabled/enabled
perf/core: Use lockdep to assert IRQs are disabled/enabled
x86: Use lockdep to assert IRQs are disabled/enabled
smp/core: Use lockdep to assert IRQs are disabled/enabled
timers/hrtimer: Use lockdep to assert IRQs are disabled/enabled
timers/nohz: Use lockdep to assert IRQs are disabled/enabled
workqueue: Use lockdep to assert IRQs are disabled/enabled
irq/softirqs: Use lockdep to assert IRQs are disabled/enabled
locking/lockdep: Add IRQs disabled/enabled assertion APIs: lockdep_assert_irqs_enabled()/disabled()
locking/pvqspinlock: Implement hybrid PV queued/unfair locks
locking/rwlocks: Fix comments
x86/paravirt: Set up the virt_spin_lock_key after static keys get initialized
block, locking/lockdep: Assign a lock_class per gendisk used for wait_for_completion()
workqueue: Remove now redundant lock acquisitions wrt. workqueue flushes
...
Worth noting are the changes to ghes_edac to use a whitelist of
known-good platforms on which GHES error reporting works relatively
reliably. By Toshi Kani and Borislav Petkov.
-----BEGIN PGP SIGNATURE-----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=XEah
-----END PGP SIGNATURE-----
Merge tag 'edac_for_4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC updates from Borislav Petkov:
"The usual pile of bugfixes, cleanups and minor driver enhancements.
Worth noting are the changes to ghes_edac to use a whitelist of
known-good platforms on which GHES error reporting works relatively
reliably. By Toshi Kani and Borislav Petkov"
* tag 'edac_for_4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC, sb_edac: Fix missing break in switch
MAINTAINERS: Split Cavium EDAC entry and add myself
EDAC, sb_edac: Fix missing DIMM sysfs entries with KNL SNC2/SNC4 mode
EDAC, skx_edac: Handle systems with segmented PCI busses
EDAC, thunderx: Remove suspend/resume support
EDAC, skx_edac: Fix detection of single-rank DIMMs
EDAC, sb_edac: Don't create a second memory controller if HA1 is not present
EDAC: Add owner check to the x86 platform drivers
EDAC: Add helper which returns the loaded platform driver
EDAC, ghes: Add platform check
EDAC, ghes: Model a single, logical memory controller
EDAC, ghes: Remove symbol exports
EDAC: Handle return value of kasprintf()
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several function prototypes for the set/get functions defined by
module_param_call() have a slightly wrong argument types. This fixes
those in an effort to clean up the calls when running under type-enforced
compiler instrumentation for CFI. This is the result of running the
following semantic patch:
@match_module_param_call_function@
declarer name module_param_call;
identifier _name, _set_func, _get_func;
expression _arg, _mode;
@@
module_param_call(_name, _set_func, _get_func, _arg, _mode);
@fix_set_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._set_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _set_func(
-_val_type _val
+const char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
@fix_get_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._get_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _get_func(
-_val_type _val
+char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
Two additional by-hand changes are included for places where the above
Coccinelle script didn't notice them:
drivers/platform/x86/thinkpad_acpi.c
fs/lockd/svc.c
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't currently harmful.
However, for some features it is necessary to instrument reads and
writes separately, which is not possible with ACCESS_ONCE(). This
distinction is critical to correct operation.
It's possible to transform the bulk of kernel code using the Coccinelle
script below. However, this doesn't handle comments, leaving references
to ACCESS_ONCE() instances which have been removed. As a preparatory
step, this patch converts the Altera EDAC code and comments to use
{READ,WRITE}_ONCE() consistently.
----
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Thor Thayer <thor.thayer@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-2-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add missing break statement in order to prevent the code from falling
through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20171016174029.GA19757@embeddedor.com
Signed-off-by: Borislav Petkov <bp@suse.de>
When figuring out the size of the DIMMs and the cluster mode is SNC2 or SNC4 the
current algorithm ignores the contribution of some of the channels resulting in
EDAC never knowing of the existence of some DIMMs attached to such channels (thus
sysfs is not populated).
Instead of selectively iterating from 0 to interlv_ways when looking for all the
participants in the interleave, do an exhaustive search and iterate from 0 to
KNL_MAX_CHANNELS. The algorithm is already smart enough to consider participants
only one time.
This works fine in all KNL cluster modes and even when there are missing DIMMs
as the contribution of those channels is 0.
Signed-off-by: Luis Felipe Sandoval Castro <luis.felipe.sandoval.castro@intel.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: arozansk@redhat.com
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: qiuxu.zhuo@intel.com
Link: http://lkml.kernel.org/r/1506606882-90521-1-git-send-email-luis.felipe.sandoval.castro@intel.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Large systems separate their PCI busses into segments since
the limit of only 256 PCI busses can be too restrictive.
Extend this driver to check whether <segment, bus-number> matches
when deciding how to group memory controller PCI devices to
CPU sockets.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: Aristeu Rozanski <arozansk@redhat.com>
Cc: Charles Rose <charles.rose@dell.com>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/f58abfd10bf73c8bc5adc1fe4de7408128b00625.1506358467.git.tony.luck@intel.com
[ Make skx_dev.seg an int. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
The memory controller on ThunderX/OcteonTX systems does not support
power management. Therefore remove the suspend/resume callbacks.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Jan Glauber <jglauber@cavium.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Suzuki K Poulose <Suzuki.Poulose@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Zhangshaokun <zhangshaokun@hisilicon.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: linux-mips@linux-mips.org
Link: http://lkml.kernel.org/r/20170925123502.17289-2-jglauber@cavium.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Single-rank DIMMs did not get detected on Skylake/Kabylake systems due
to wrong limit check. The single rank DIMM check is a simple typo. "0"
is a legal value in this field meaning single rank.
Signed-off-by: Charles Rose <charles.rose@dell.com>
Cc: Aristeu Rozanski <arozansk@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/66df72d327c265fbf92fe25df96daa228a35f076.1506358467.git.tony.luck@intel.com
[ Also fix debug message to print number of ranks. ]
Signed-off-by: Tony Luck <tony.luck@intel.com>
[ Expand commit message. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Yi Zhang reported the following failure on a 2-socket Haswell (E5-2603v3)
server (DELL PowerEdge 730xd):
EDAC sbridge: Some needed devices are missing
EDAC MC: Removed device 0 for sb_edac.c Haswell SrcID#0_Ha#0: DEV 0000:7f:12.0
EDAC MC: Removed device 1 for sb_edac.c Haswell SrcID#1_Ha#0: DEV 0000:ff:12.0
EDAC sbridge: Couldn't find mci handler
EDAC sbridge: Couldn't find mci handler
EDAC sbridge: Failed to register device with error -19.
The refactored sb_edac driver creates the IMC1 (the 2nd memory
controller) if any IMC1 device is present. In this case only
HA1_TA of IMC1 was present, but the driver expected to find
HA1/HA1_TM/HA1_TAD[0-3] devices too, leading to the above failure.
The document [1] says the 'E5-2603 v3' CPU has 4 memory channels max. Yi
Zhang inserted one DIMM per channel for each CPU, and did random error
address injection test with this patch:
4024 addresses fell in TOLM hole area
12715 addresses fell in CPU_SrcID#0_Ha#0_Chan#0_DIMM#0
12774 addresses fell in CPU_SrcID#0_Ha#0_Chan#1_DIMM#0
12798 addresses fell in CPU_SrcID#0_Ha#0_Chan#2_DIMM#0
12913 addresses fell in CPU_SrcID#0_Ha#0_Chan#3_DIMM#0
12674 addresses fell in CPU_SrcID#1_Ha#0_Chan#0_DIMM#0
12686 addresses fell in CPU_SrcID#1_Ha#0_Chan#1_DIMM#0
12882 addresses fell in CPU_SrcID#1_Ha#0_Chan#2_DIMM#0
12934 addresses fell in CPU_SrcID#1_Ha#0_Chan#3_DIMM#0
106400 addresses were injected totally.
The test result shows that all the 4 channels belong to IMC0 per CPU, so
the server really only has one IMC per CPU.
In the 1st page of chapter 2 in datasheet [2], it also says 'E5-2600 v3'
implements either one or two IMCs. For CPUs with one IMC, IMC1 is not
used and should be ignored.
Thus, do not create a second memory controller if the key HA1 is absent.
[1] http://ark.intel.com/products/83349/Intel-Xeon-Processor-E5-2603-v3-15M-Cache-1_60-GHz
[2] https://www.intel.com/content/dam/www/public/us/en/documents/datasheets/xeon-e5-v3-datasheet-vol-2.pdf
Reported-and-tested-by: Yi Zhang <yizhan@redhat.com>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Fixes: e2f747b1f4 ("EDAC, sb_edac: Assign EDAC memory controller per h/w controller")
Link: http://lkml.kernel.org/r/20170913104214.7325-1-qiuxu.zhuo@intel.com
[ Massage commit message. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Change x86 EDAC platform drivers to verify the module owner at the
beginning of their module init functions. This allows them to fail their
init immediately when ghes_edac is enabled. Similar change can be made
to other edac drivers if necessary.
Also, remove ".c" from module names of pnp2_edac, sb_edac, and skx_edac.
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Suggested-by: Borislav Petkov <bp@alien8.de>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170823225447.15608-6-toshi.kani@hpe.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Only a single EDAC platform driver can be loaded. When ghes_edac is
enabled, an EDAC platform driver still attempts to register itself and
fails in edac_mc_add_mc().
Add edac_get_owner() so that EDAC platform drivers can check the owner
first.
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Suggested-by: Borislav Petkov <bp@alien8.de>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170823225447.15608-5-toshi.kani@hpe.com
[ Massage commit message. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
The ghes_edac driver was introduced in 2013 [1], but it has not been
enabled by any distro yet. This driver obtains error info from firmware
interfaces (APEI), which are not properly implemented on many platforms,
as the driver says on load:
This EDAC driver relies on BIOS to enumerate memory and get error
reports. Unfortunately, not all BIOSes reflect the memory layout
correctly. So, the end result of using this driver varies from vendor
to vendor. If you find incorrect reports, please contact your hardware
vendor to correct its BIOS.
To get out from this situation, add a platform check to selectively
enable the driver on platforms that are known to have proper APEI
firmware implementation.
"ghes_edac.force_load=1" skips this platform check.
[1]: https://lkml.kernel.org/r/cover.1360931635.git.mchehab@redhat.com
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-acpi@vger.kernel.org
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170823225447.15608-4-toshi.kani@hpe.com
Signed-off-by: Borislav Petkov <bp@suse.de>
We're enumerating the DIMMs through a DMI walk and since we can't get
any more detailed topological information about which DIMMs belong to
which memory controller, convert it to a single, logical controller
which contains all the DIMMs.
The error reporting path from GHES ghes_edac_report_mem_error() doesn't
get called in NMI context but add a warning about it to catch any
changes in the future as if so, our locking scheme will be insufficient
then.
Signed-off-by: Borislav Petkov <bp@suse.de>
kasprintf() can fail and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: linux-edac@vger.kernel.org
[ Merged into a single patch, small formatting fixups. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
struct mce.cpuid contains CPUID(1).EAX which contains family, model and
stepping and thus has enough information for our purposes. Thus get rid
of some external dependencies which are not really needed.
No functionality change.
Signed-off-by: Borislav Petkov <bp@suse.de>
Make these const as they are only stored in the type field of a device
structure, which is const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1503130946-2854-2-git-send-email-bhumirks@gmail.com
Signed-off-by: Borislav Petkov <bp@suse.de>
On Deverton server, the P2SB PCI device (DEV:1F, FUN:1) is used by multiple
device drivers.
If it's hidden by some device driver (e.g. with the i801 I2C driver,
the commit
9424693035 ("i2c: i801: Create iTCO device on newer Intel PCHs")
unconditionally hid the P2SB PCI device wrongly) it will make the
pnd2_edac driver read out an invalid BAR value of 0xffffffff and then
fail on ioremap().
Therefore, store the presence state of P2SB PCI device before unhiding
it for reading BAR and restore the presence state after reading BAR.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: linux-i2c@vger.kernel.org
Link: http://lkml.kernel.org/r/20170814154845.21663-1-qiuxu.zhuo@intel.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Bit[0] of BAR is always zero. Bit[2:1] and bit[3] of BAR contain the
information of 'type' and the 'prefetchable' accordingly. Therefore,
mask the lower four bits to retrieve the actual base address of a BAR.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170814154813.21619-1-qiuxu.zhuo@intel.com
Signed-off-by: Borislav Petkov <bp@suse.de>
I've been waing a long time for the generic sideband driver to
appear. Patience has run out, so include the minimum here to
just read registers.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: Aristeu Rozanski <arozansk@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Patrick Geary <patrickg@supermicro.com>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170803210536.5662-1-tony.luck@intel.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Basically, there are full memory mirroring and address range partial
memory mirroring (supported by Haswell EX and Broadwell EX) modes.
a) In full memory mirroring, the memory behind each memory controller
is mirrored, i.e. the memory is split into two identical mirrors
(primary and secondary), half of the memory is reserved for redundancy.
b) In address range partial memory mirroring, the memory size (range)
of primary and secondary behind each memory controller can be user
defined by the TAD0 register. The rest of memory ranges defined by
TAD1/TAD2/... in that memory controller are non-mirrored.
For more detail on memory mirroring, see the following link written by Tony Luck:
https://01.org/lkp/blogs/tonyluck/2016/address-range-partial-memory-mirroring-linux
Currently the sb_edac driver only supports address decoding in full
memory mirroring and non-mirroring modes. In address range partial
memory mirroring mode, it may fail to decode an address that falls in a
non-mirroring area (the following was one of this kind of failed logs).
mce: Uncorrected hardware memory error in user-access at 566d53a400
Memory failure: 0x566d53a: Killing einj_mem_uc:4647 due to hardware memory corruption
Memory failure: 0x566d53a: recovery action for dirty LRU page: Recovered
mce: [Hardware Error]: Machine check events logged
EDAC sbridge MC1: HANDLING MCE MEMORY ERROR
EDAC sbridge MC1: CPU 48: Machine Check Event: 0 Bank 7: ec00000000010090
EDAC sbridge MC1: TSC 4b914aa5a99dab
EDAC sbridge MC1: ADDR 566d53a400
EDAC sbridge MC1: MISC 1443a0c86
EDAC sbridge MC1: PROCESSOR 0:406f1 TIME 1499712764 SOCKET 2 APIC 80
EDAC MC1: 0 UE Can't discover the memory rank for ch addr 0x7fb54e900 on any memory ( page:0x0 offset:0x0 grain:32)
mce: [Hardware Error]: Machine check events logged
Therefore, classify memory mirroring modes and make the address decoding
in address range partial memory mode correct.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170730180651.30060-1-qiuxu.zhuo@intel.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing of
the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170718214339.7774-19-robh@kernel.org
Signed-off-by: Borislav Petkov <bp@suse.de>
It is a write-only variable so get rid of it.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Robert Richter <rric@kernel.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Thor Thayer <thor.thayer@linux.intel.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Cc: Mark Gross <mark.gross@intel.com>
Cc: Tim Small <tim@buttersideup.com>
Cc: Ranganathan Desikan <ravi@jetztechnologies.com>
Cc: "Arvind R." <arvino55@gmail.com>
Cc: Jason Baron <jbaron@akamai.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Daney <david.daney@cavium.com>
Cc: Loc Ho <lho@apm.com>
Cc: linux-edac@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mips@linux-mips.org
Using the homegrown amd_get_nb_id() to find a node ID on AMD was fine
while the L3 to node mapping was 1:1. And Zen topology broke this. So
let's start slowly moving away from it and use the topology interfaces
instead.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: x86-ml <x86@kernel.org>
Link: http://lkml.kernel.org/r/1490041614-90057-2-git-send-email-Yazen.Ghannam@amd.com
[ Massage commit message. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Non-existent or empty DIMM slots result in error return from
RD_REGP(). But we shouldn't give up on failure.
So long as we find at least one DIMM we can continue.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170628234407.21521-1-tony.luck@intel.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Isaac Vaughn