If the DMAs are not being quiesced properly, it may lead to
stability issues, so the recommendation is to wait till DMAs are
stopped.
After setting the stop bit of RIRB/CORB DMA, we should wait for
stop bit to be set.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ebus is a member of extended device and was never initialized, so
do this at device creation.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This helper is copied from legacy hda driver.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a fairly large collection of fixes but almost all driver
specific ones, especially to the new Intel drivers which have had a lot
of recent development. The one core fix is a change to the debugfs code
to avoid crashes in some relatively unusual configurations.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXINZtAAoJECTWi3JdVIfQ+BwH/1eLqMfCSZM9nsDr1QMvOCDP
SO4ZoWqvYplBcS8pYKbJmqtuo8jMxT3VIQF+b5hPAVhgpLwMmy9qeFtatqCQ2WDC
GfCqW8LSKtrzwUwmoRrtHx7vfBLP1/z78F8ORQzwhrplTCBhvPLbUOrV51EFj6tf
Dfo2tW0uxww9iCZduYu4LadOhFOfuw+5shUrJk5A5f975Zbdgyke4CbRnlbDPXLq
d4i7bNfiISkSJiKMpdZFeiOQCd0+uXHh2WkMtVYSGVTA2Kf7d7HtX+JpEFFmaJgJ
8CndjgNJ1ZXtMHl1pMYmNqKJ5mEgmVtbGGJWY4QmQBva0EfQ+vLZt78BG3qvJwk=
=SXH2
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v4.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.6
This is a fairly large collection of fixes but almost all driver
specific ones, especially to the new Intel drivers which have had a lot
of recent development. The one core fix is a change to the debugfs code
to avoid crashes in some relatively unusual configurations.
The recent bug report suggests that BCLK setup for i915 HSW/BDW needs
to be updated at each HDMI hotplug, not only at initialization and
resume. That is, we need to update HSW_EM4 and HSW_EM5 registers at
ELD notification, too. Otherwise the HDMI audio may be out of sync
and played in a wrong pitch.
However, the HDA codec driver has no access to the controller
registers, and currently the code managing these registers is in
hda_intel.c, i.e. local to the controller driver. For allowing the
explicit BCLK update from the codec driver, as in this patch, the
former haswell_set_bclk() in hda_intel.c is moved to hdac_i915.c and
exposed as snd_hdac_i915_set_bclk(). This is called from both the HDA
controller driver and intel_pin_eld_notify() in HDMI codec driver.
Along with this change, snd_hdac_get_display_clk() gets dropped as
it's no longer used.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91410
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HD-audio driver uses regmap cache bypass feature for reading a raw
value without the cache. But this is racy since both the cached and
the uncached reads may occur concurrently. The former is done via the
normal control API access while the latter comes from the proc file
read.
Even though the regmap itself has the protection against the
concurrent accesses, the flag set/reset is done without the
protection, so it may lead to inconsistent state of bypass flag that
doesn't match with the current read and occasionally result in a
kernel WARNING like:
WARNING: CPU: 3 PID: 2731 at drivers/base/regmap/regcache.c:499 regcache_cache_only+0x78/0x93
One way to work around such a problem is to wrap with a mutex. But in
this case, the solution is simpler: for the uncached read, we just
skip the regmap and directly calls its accessor. The verb execution
there is protected by itself, so basically it's safe to call
individually.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=116171
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The existing TLV callback implementation copies all of the
cea_channel_speaker_allocation map table to the TLV container
irrespective of what is reported by sink. This is of little use
to the userspace application.
With this patch, it parses the spk_alloc block as queried from
the ELD, and copies only the corresponding mapping channel
allocation entries from the cea channel speaker allocation table.
Thus the user can parse the TLV container to identify sink's
capability and set the channel map accordingly.
It shouldn't impact the behavior in AMD chipset, as this makes
use of already parsed spk alloc block to calculate the channel
map.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On Skylake and onwards, the HD-audio controller driver needs to bind
with i915 for having the control of power well audio domain before
actually probing the codec. This leads to the load of i915 driver
from the audio driver side. But, there are systems that have no Intel
graphics but Nvidia or AMD GPU, although they still use HD-audio bus
for the onboard audio codecs. On these, loading the i915 driver is
nothing but a useless memory and CPU consumption.
A simple way to avoid it is just to look for the Intel graphics PCI
entry beforehand, and try to bind with i915 only when such an entry is
found. Currently, it assumes the PCI display class. If another class
appears, this needs to be extended (although it's very unlikely).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The hdac_acomp object in hdac_i915.c is left as assigned even after
binding with i915 actually fails, and this leads to the WARN_ON() at
the next load of the module.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94736
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit [d745f5e7b8b2: ALSA: hda - Add the pin / port mapping on
Intel ILK and VLV] introduced a WARN_ON() to check the pointer for
avoiding the double initializations. But hdac_acomp pointer wasn't
cleared at snd_hdac_i915_exit(), thus after reloading the HD-audio
driver, it may result in the false positive warning. This patch makes
sure to clear the leftover pointer at exit.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94736
Reported-by: Daniela Doras-prodan <daniela.doras-prodan@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Intel IronLake and ValleyView platforms have different HDMI widget pin
and digital port mapping from other newer ones. The recent ones
(HSW+) have NID 0x05 to 0x07 for port B to port D, while these chips
have NID 0x04 to 0x06.
For adapting this mapping, pass the codec object instead of the bus
object to snd_hdac_sync_audio_rate() and snd_hdac_acomp_get_eld() so
that they can check the codec ID and calculate the mapping properly.
The changes in the HDMI codec driver side will follow in the later
patch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It is always better to use list_for_each_entry_safe() while doing
cleanup. So use this instead of open coding this in list in
snd_hdac_stream_free_all()
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is an implicit rule to map between pin NID and port number on
Intel HDMI/DP codec: the mapping is fixed only for NID 0x05, 0x06 and
0x07. For avoiding the possible memory corruption, add a sanity check
for the NID value and splat WARN_ON() for invalid accesses.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HD-audio driver has a mechanism to trigger the runtime resume
automatically at accessing the verbs. This auto-resume, however,
causes the mutex deadlock when invoked from the regmap handler since
the regmap keeps the mutex while auto-resuming. For avoiding that,
there is some tricky check in the HDA regmap handler to return -EAGAIN
error to back-off when the codec is powered down. Then the caller of
regmap r/w will retry after properly turning on the codec power.
This works in most cases, but there seems a slight race between the
codec power check and the actual on-demand auto-resume trigger. This
resulted in the lockdep splat, eventually leading to a real deadlock.
This patch tries to address the race window by getting the runtime PM
refcount at the check time using pm_runtime_get_if_in_use(). With
this call, we can keep the power on only when the codec has been
already turned on, and back off if not.
For keeping the code consistency, the code touching the runtime PM is
stored in hdac_device.c although it's used only locally in
hdac_regmap.c.
Reported-by: Jiri Slaby <jslaby@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add slot and channel count programming to hdmi_chmap object and
move the chmap_ops to core. Use register_chmap_ops API to
register for default ops. Override specific chmap ops in the
driver.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently the interrupt handler of HD-audio driver assumes that no irq
update is needed while processing the irq. But in reality, it has
been confirmed that the HW irq is issued even during the irq
handling. Since we clear the irq status at the beginning, process the
interrupt, then exits from the handler, the lately issued interrupt is
left untouched without being properly processed.
This patch changes the interrupt handler code to loop over the
check-and-process. The handler tries repeatedly as long as the IRQ
status are turned on, and either stream or CORB/RIRB is handled.
For checking the stream handling, snd_hdac_bus_handle_stream_irq()
returns a value indicating the stream indices bits. Other than that,
the change is only in the irq handler itself.
Reported-by: Libin Yang <libin.yang@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently HD-audio driver on Intel Skylake or Broxteon gives an error
message when binding with i915 audio component fails. However, this
isn't any serious error on a system without Intel graphics. Indeed
there are such systems, where a third-party codec (e.g. Creative) is
put on the mobo while using other discrete GPU (e.g. Nvidia).
Printing a kernel "error" message is overreaction in such a case.
This patch downgrades the print level for that message. For systems
that mandate the i915 binding (e.g. Haswell or Broadwell HDMI/DP),
another kernel error message is shown in addition to make clear what
went wrong.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=111021
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A bunch more updates for v4.5, mainly driver work:
- More topology API enhancements from Mengdong Lin working towards
making everything more component based and being able to specify PCM
links via topology.
- Large sets driver updates from Cirrus, Intel (mainly more Skylake
support) and Renesas.
- New drivers for AMD ACP, Atmel PDMIC, Dialog DA7218, Imagination
Technologies SoC IPs, Rockchip RK3036 Inno CODEC and Texas Instruments
PCM3168A.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWk8EUAAoJECTWi3JdVIfQ+RwH/jid388X6x6YOa84Rs7InrIS
m2rVdjDAMAbK+smhalHzvLOGnHjpygegwZ/9/1DUiSPbcXdqMkzLoaweeVUXhu27
9G3zT0Xz1XVn/+5029oIlrsyPCtM5O9PlPOO7tiQSTBADjvl+I4hl6FHZ1LGT7Sr
tiOTAiOmIisELBzBF0L7fB18iBgE3VqkhG8obrMiTXVWgfZuRJL7kdH2WuHYFXpM
JxBcy9VrCp0JHxg+qCD7xYyFdKLE6eP96gpLi94JBqW8I3wrwmEmUqNKs+r8I7Vj
bh5/v6A2V0EaJWCKzWBARHE7BR3E2uJeoD0PcY59Kn7BKhKPjTe99g2ngTk1hIU=
=BvEm
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.4-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Last updates for v4.5
A bunch more updates for v4.5, mainly driver work:
- More topology API enhancements from Mengdong Lin working towards
making everything more component based and being able to specify PCM
links via topology.
- Large sets driver updates from Cirrus, Intel (mainly more Skylake
support) and Renesas.
- New driver for AMD ACP
- Rename PCM1792a driver to be generic pcm179x
We have an API for powering down all links, we need a similar one
for powering up links, so add for power up as well
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
HW recommends 180us for worst case values for link power up
delay, so change the current delay value from 50 (150us) to 150
(450us)
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
A stream is by default in coupled mode, in DSP operation we move
it to decoupled mode. On cleanup HW expects that we leave it back
to default state so couple the DMA on cleanup.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Skylake sports new capability of DMA resume, DRSM where we can
resume the DMA. This capability is defined by presence of
AZX_DRSM_CAP_ID.
If this capability is present, we use this capability.
So we add:
snd_hdac_ext_stream_drsm_enable() - DMA resume caps
snd_hdac_ext_stream_set_dpibr() - set the DMA position
snd_hdac_ext_stream_set_lpib() - set the lpib
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
A couple of i915_audio_component ops have been added and accessed
directly from patch_hdmi.c. Ideally all these should be factored out
into hdac_i915.c.
This patch does it, adds two new helper functions for setting N/CTS
and fetching ELD bytes. One bonus is that the hackish widget vs port
mapping is also moved to hdac_i915.c, so that it can be fixed /
enhanced more cleanly.
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Give some readable comment in kernel doc style for each exported
function, as I promised in the previous meetings. While we're at it,
fix the wrong comments, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
By setting the MODALIAS variable in uevents, userspace helpers will be
enabled to load modules via the module alias associated with a device.
This information is required to automatically load HDA codec drivers
instead of having to explicitly request the various modules in the HDA
core code.
[Note that currently the legacy HDA controller driver tries to bind
codec modules manually. It's for supporting the fallback generic
drivers. This new udev modalias support was added rather for ASoC
HDA ext drivers, since this addition itself won't hurt the legacy HDA
-- tiwai]
[Use the common helper function to generate the modalias -- tiwai]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Subhransu S Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch just adds modalias sysfs entry to each hdaudio bus entry.
[rewritten to call the common helper function by tiwai]
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Subhransu S Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch provide a new common helper function,
snd_hdac_codec_modalias(), to give the codec modalias name string.
This function will be used by multiple places in the later patches.
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Subhransu S Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For generating modalias entries automatically, move the definition of
struct hda_device_id to linux/mod_devicetable.h and add the handling
of this record in file2alias helper. The new modalias is represented
with combination of vendor id, device id, and api version as
"hdaudio:vNrNaN".
This patch itself doesn't convert the existing modaliases. Since they
were added manually, this patch won't give any regression by itself at
this point.
[Modified the modalias format to adapt the api_version field, and drop
invalid ANY_ID definition by tiwai]
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Subhransu S Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few multiple codec drivers do renaming the chip_name string but all
these are open-coded and some of them have even no error check. Let's
make common helpers to do it properly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Compiling the hdac extended core on arm fails with below error:
sound/hda/ext/hdac_ext_bus.c: In function 'hdac_ext_writel':
>> sound/hda/ext/hdac_ext_bus.c:29:2: error: implicit declaration of
>> function
+'writel' [-Werror=implicit-function-declaration]
writel(value, addr);
^
sound/hda/ext/hdac_ext_bus.c: In function 'hdac_ext_readl':
>> sound/hda/ext/hdac_ext_bus.c:34:2: error: implicit declaration of
>> function
+'readl' [-Werror=implicit-function-declaration]
return readl(addr);
This is fixed by explicitly including io.h
Fixes: 99463b3a39 - ('ALSA: hda: provide default bus io ops extended hdac')
Reported-by: kbuild test robot <lkp@intel.com>
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current codec helpers are local to hda code and needs to be moved to
core so that other users can use it.
The helpers to read/write the codec and to check the
power state of widgets is copied
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
if the stream is decoupled and both link and host are used, while
releasing the stream, need to check if link and host stream are
not in use. This patch adds fix to check if the host/link stream
is in used before coupling it back when releasing the stream.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Bits in LOSIDV need to be set to map the stream id for specific link.
Fixing this by setting the required bits in the register.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This lets the interested codec be notified when an i915 pin/ELD
event happens.
[tiwai: Fixed a trivial build error for CONFIG_SND_HDA_I915=n]
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When snd_hdac_refresh_widget_sysfs() is called before the first
hda_widget_sysfs_init(), the next call overrides and eventually
fails. This results in unexpected Oops, something like:
BUG: unable to handle kernel NULL pointer dereference at 00000000000000c8
IP: [<ffffffff8180e2a3>] hdmi_chmap_ctl_info+0x23/0x40
The fix is to add a check of the existing sysfs tree. Also, for more
safety, this patch adds the checks of device_is_registered() in
snd-hdac_refresh_wdiget_sysfs(), too.
Fixes: fa4f18b4f4 ('ALSA: hda - Refresh widgets sysfs at probing Haswell+ HDMI codecs')
Bugizlla: https://bugzilla.kernel.org/show_bug.cgi?id=103431
Reported-by: Andreas Reis <andreas.reis@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a helper to find the stream using stream tag and direction.
This is useful for drivers to query stream based on stream tag
and direction, fox example while downloading FW thru DSP loader
code
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
spbmaxfifo API is actually a query function not a set function so
name it snd_hdac_ext_stream_get_spbmaxfifo()
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While creating hdac_ext_device, we used hdev for sizeof insteadof
edev, which resulted in eventual crash of the system Fix the size
here
Fixes: a512f56116 ('ALSA: hdac: add hdac extended device')
Reported-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
hdac_ext_stream assign doesn't require key mapping as in case of
hdac_stream. So for host stream, the key to device mapping needs
to be removed.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The drivers need to set the spib and maxfifios values, so add
these new APIs snd_hdac_ext_stream_set_spib() and
snd_hdac_ext_stream_set_spbmaxfifo() APIs
For these APIs we also need to have spib and fifos pointer, so
add these to hdac_ext_stream and initialize them at stream init
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
New HDA controllers like Skylake sport multiple HDA links, so we need a
helper to turn off all the links in one go while suspending the device so
add snd_hdac_ext_bus_link_power_down_all() API
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SPCAP and Mutilink register offset were incorrect as offset needs
to be based on capability offset. So correct the offset for
read/write of spcap/link register.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some codecs like Intel HDMI by default do not show up all the pins, they
have to be manually enabled, so we need to refresh the codec widgets and
then recreate the sysfs tree. So add new API snd_hdac_refresh_widget_sysfs()
to do this. It should be be used by codec driver after sending magic verbs
to codec
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds new extended driver objects and API for registering the
extended devices.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds based hdac extended device object which will be used by
ASoC HDAC codecs
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HDAC extended device objects are created by HDAC extended bus on probe.
When controller is removed they should be removed as well, so add API
snd_hdac_ext_bus_device_remove for this
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The snd_hdac_chip_readl return can never be less than zeros,
so no point in checking for the return value
This fixes following static checker warnings in
snd_hdac_ext_bus_parse_capabilities
sound/hda/ext/hdac_ext_controller.c:47
snd_hdac_ext_bus_parse_capabilities()
warn: unsigned 'offset' is never less than zero.
sound/hda/ext/hdac_ext_controller.c:54
snd_hdac_ext_bus_parse_capabilities()
warn: unsigned 'cur_cap' is never less than zero.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This fixes issue in assigning host stream in case of
decoupled mode. The check to verify if the stream is already
in use was wrong so fix that
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the controller is powered up but the HDMI codec is powered down
on Skylake, the power well is turned off. When the codec is then
powered up again, we need to poke the codec a little extra to make
sure it wakes up. Otherwise we'll get sad "no response from codec"
messages and broken audio.
This also changes azx_runtime_resume to actually call
snd_hdac_set_codec_wakeup for Skylake (before STATETS read).
(Otherwise it would only have been called for Haswell and Broadwell,
which both do not need it, so this probably was not the author's
intention.)
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Reviewed-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch changes the return type of snd_hdac_power_up/down() and
variants to pass the error code from the underlying
pm_runtime_get/put() calls. Currently they are ignored, but in most
places, these should be handled properly.
As an example, the regmap handler is updated to check the return value
and accesses the register only when the wakeup succeeds.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The kobject_put() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A typical io ops use simple io accessors which can be common for most
drivers, so provide a default ops which will be used if driver doesn't
provide one
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In HDA extended bus the HDA link objects are created when multilink
capabilities are parsed. We need a routine which free up these link objects
for a bus. So add snd_hdac_link_free_all routine
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDAC extended core should create streams for an extended bus and also free
up those on cleanup. So introduce snd_hdac_ext_stream_init_all and
snd_hdac_stream_free_all routines
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since this is common option for HDA driver to specfiy pre-allocated
buffer, we should make this option availble to all HDA driver by
moving this to HDA core
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now we have the bus and controller code added to find and initialize
the extended capabilities. Now we need to use them in stream code to
decouple stream, manage links etc
So this patch adds the stream handling code for extended capabilities
introduced in preceding patches
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The controller needs to support the new capabilities and allow
reading, parsing and initializing of these capabilities, so this patch
does it
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The new HDA controllers from Intel support new capabilities like
multilink, pipe processing, SPIB, GTS etc In order to use them we
create an extended HDA bus which embed the hdac bus and contains the
fields for extended configurations
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Yet another regression by the transition to regmap cache; for better
usability, we had the fake mute control using the zero amp value for
Conexant codecs, and this was forgotten in the new hda core code.
Since the bits 4-7 are unused for the amp registers (as we follow the
syntax of AMP_GET verb), the bit 4 is now used to indicate the fake
mute. For setting this flag, snd_hda_codec_amp_update() becomes a
function from a simple macro. The bonus is that it gained a proper
function description.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This merges and resolves the non-trivial conflicts with the recent fix
for hda-i915 binding fallback.
Conflicts:
sound/pci/hda/hda_intel.c
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the missing NULL checks so that snd_hdac_i915*() can be called
even after the binding with i915 failed.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Along with the transition to regmap for managing the cached parameter
reads, the caps overwrite was also moved to regmap cache. The cache
change itself works, but it still tries to write the non-existing verb
(the HDA parameter is read-only) wrongly. It's harmless in most
cases, but some chips are picky and may result in the codec
communication stall.
This patch avoids it just by adding the missing flag check in
reg_write ops.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA codec drivers can be matched using vendor id and revision id typically.
So provide a match function which does this and is loaded when driver hasn't
provided one (default behaviour)
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The file is moved to hda core and renamed to hdac_i915.c, so can be used
by both legacy HDA driver and new Skylake audio driver.
- Add snd_hdac_ prefix to the public APIs.
- The i915 audio component is moved to core bus and dynamically allocated.
- A static pointer hdac_acomp is used to help bind/unbind callbacks to get
this component, because the sound card's private_data is used by the azx
chip pointer, which is a legacy structure. It could be removed if private
_data changes to some core structure which can be extended to find the
bus.
- snd_hdac_get_display_clk() is added to get the display core clock for
HSW/BDW.
- haswell_set_bclk() is moved to hda_intel.c because it needs to write the
controller registers EM4/EM5, and only legacy HD-A needs it for HSW/BDW.
- Move definition of HSW/BDW-specific registers EM4/EM5 to hda_register.h
and rename them to HSW_EM4/HSW_EM5, because other HD-A controllers have
different layout for the extended mode registers.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The CA0132 DSP loader leads to NULL deference since the recent
transition to HDA core code, as it unconditionally accesses
hdac_stream->substream->runtime. For DSP loading, the substream
shouldn't be assigned.
This patch addresses the NULL dereference above in addition to assure
the substream is cleared while DSP loading.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=98151
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the trace of snd_hdac_stream_start and snd_hdac_stream_stop.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A flag "link_power_control" is added to indicate whether a codec needs to
control the link power. And a new bus ops link_power() is defined for the
codec to request to enable/disable the link power.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This will be used by hda controller driver to
setup stream params in prepare. This function will
setup the bdl and periods.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For fixing randconfig build errors like:
sound/hda/hdac_stream.c: In function 'azx_timecounter_init':
sound/hda/hdac_stream.c:365:2: error: implicit declaration of function 'CLOCKSOURCE_MASK' [-Werror=implicit-function-declaration]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the controller helper codes to hda-core library.
The I/O access ops are added to the bus ops. The CORB/RIRB, the basic
attributes like irq# and iomap address, some locks and the list of
streams are added to the bus object, together with the stream object
and its helpers.
Currently the codes are just copied from the legacy driver, so you can
find duplicated codes in both directories. Only constants are removed
from the original hda_controller.h. More integration work will follow
in the later patches.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some HD-A codecs may add their own vendor 'set' verb to the regmap, thru func
snd_hdac_add_vendor_verb(). This patch sets the GET bit (bit 11) when adding
the verb so that its peer vendor 'get' verb is actually added. This can avoid
I/O error when writing the 'set' verb thru remap, since HD-A regmap internally
looks up a writable vendor verb with GET bit set at first.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Although some races in runtime PM refcount was fixed by the commit
[664c715573c2: ALSA: hda - Work around races of power up/down with
runtime PM], there is still a race in the following case:
CPU0: CPU1 :
runtime suspend:
codec->in_pm = 1
snd_hdac_power_up_pm():
pm_runtime_get_sync() skipped
suspend finished:
codec->in_pm = 0
snd_hdac_power_down_pm():
pm_runtime_put_*() is called!
For avoiding this situation, increment in_pm flag atomically when it's
non-zero, and decrement accordingly, to ensure that in_pm is set
consistently for the whole concurrent operations.
Also, since atomic_inc_not_zero() and atomic_dec_if_positive() are
lengthy inline functions, move snd_hdac_power_up_pm() and _down_pm()
to sound/hda/hdac_device.c as no inline functions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The type field of HD-audio codec object should be exposed to
user-space so that it can identify which driver type to bind (legacy /
asoc).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The hdac regmap code checks whether the codec is powered on while
accessing, but there must be an exception -- the verbs to control the
power state.
Currently HD-audio driver doesn't access them via regmap, so this
patch doesn't fix any current behavior, but it's just for future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, snd_hdac_power_up()/down() helpers checks whether the codec
is being in pm (suspend/resume), and skips the call of runtime get/put
during it. This is needed as there are lots of power up/down
sequences called in the paths that are also used in the PM itself. An
example is found in hda_codec.c::codec_exec_verb(), where this can
power up the codec while it may be called again in its power up
sequence, too.
The above works in most cases, but sometimes we really want to wait
for the real power up. For example, the control element get/put may
want explicit power up so that the value change is assured to reach to
the hardware. Using the current snd_hdac_power_up(), however,
results in a race, e.g. when it's called during the runtime suspend is
being performed. In the worst case, as found in patch_ca0132.c, it
can even lead to the deadlock because the code assumes the power up
while it was skipped due to the check above.
For dealing with such cases, this patch makes snd_hdac_power_up() and
_down() to two variants: with and without in_pm flag check. The
version with pm flag check is named as snd_hdac_power_up_pm() while
the version without pm flag check is still kept as
snd_hdac_power_up(). (Just because the usage of the former is fewer.)
Then finally, the patch replaces each call potentially done in PM with
the new _pm() variant.
In theory, we can implement a unified version -- if we can distinguish
the current context whether it's in the pm path. But such an
implementation is cumbersome, so leave the code like this a bit messy
way for now...
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=96271
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... so that user-space can know that the whole nodes have been
created. Unfortunately, this can't be implemented easily in race-free
way, so it's a kind of compromise.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This merges the support of regmap in HD-audio infrastructure.
Many in-house cache codes in HD-audio driver are relaced with the
more standard regmap base now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A regression was introduced in 7639a06c23c7d4cda3: if AC_PAR_SUBSYSTEM_ID
reads as zero, one should retry using AC_VERB_GET_SUBSYSTEM_ID.
This seems to hit many codecs (my own laptop included), and causes
quirks for some machines not to apply correctly.
Reported-by: TienFu Chen <tienfu.chen@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HD-audio doesn't support the bulk access. Currently it works even
without this flag as implicitly assumed, but it's safer to set
explicitly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Although they can be written, handle a few verbs as read-only in
regmap interface: CONFIG_DEFAULT, CONV and CVT_CHAN_COUNT. These are
either updated in PCM or HDMI management code in a volatile manner, or
just needed only as parameter, thus they don't need to be written at
resume sync.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The 16bit COEF read/write is pretty standard for many codecs, and they
can be cached in most cases -- more importantly, they need to be
restored at resume. For making this easier, add the cache support to
regmap. If the codec driver wants to cache the COEF access, set
codec->cache_coef flag and issue AC_VERB_GET_PROC_COEF with the coef
index in LSB 8 bits.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HD-audio has quite a few asymmetrical ways of accessing verbs, and one
of typical ones is GET/SET_POWER_STATE verbs. While it takes only the
power state for setting, it returns a combination of states for
getting. For making the state handling simpler, this patch adds a
code to translate the value returned from GET_POWER_STATE to return
only the actual state or -1 for error. In that way, the driver can
simplify the power state management.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HD-audio spec is inconvenient regarding the handling of stereo volume
controls. It can set and get only single channel at once (although
there is a special option to set the same value to both channels).
This patch provides a fake pseudo-register via the regmap access so
that the stereo channels can be read and written by a single call.
It'd be useful, for example, for implementing DAPM widgets.
A stereo amp pseudo register consists of the encoding like the normal
amp verbs but it has both SET_LEFT (bit 13) and SET_RIGHT (bit 12)
bits set. The regmap reads and writes a 16bit value for this pseudo
register where the upper 8bit is for the right chanel and the lower
8bit for the left channel.
Note that the driver doesn't recognize conflicts when both stereo and
mono channel registers are mixed. Mixing them would certainly confuse
the operation. So, use carefully.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Codecs may have own vendor-specific verbs, and we need to allow each
driver to give such verbs for cached accesses. Here a verb can be put
into a single array and looked through it at readable and writeable
callbacks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The amp hash table was used for recording the cached reads of some
capability values like pin caps or amp caps. Now all these are moved
to regmap as well.
One addition to the regmap helper is codec->caps_overwriting flag.
This is set in snd_hdac_override_parm(), and the regmap helper accepts
any register while this flag is set, so that it can overwrite even the
read-only verb like AC_VERB_PARAMETERS. The flag is cleared
immediately in snd_hdac_override_parm(), as it's a once-off flag.
Along with these changes, the no longer needed amp hash and relevant
fields are removed from hda_codec struct now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Sometimes we need the uncached reads, e.g. for refreshing the tree.
This patch provides the helper function for that and uses it for
refreshing widgets, reading subtrees and the whole proc reads.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Let's start converting the access functions to regmap.
The first one is the simplest, just converting the codec parameter
read helper function snd_hda_param_read().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds an infrastructure to support regmap-based verb
accesses. Because o the asymmetric nature of HD-audio verbs,
especially the amp verbs, we need to translate the verbs as a sort of
pseudo registers to be mapped uniquely in regmap.
In this patch, a pseudo register is built from the NID, the
AC_VERB_GET_* and 8bit parameters, i.e. almost in the form to be sent
to HD-audio bus but without codec address field. OTOH, for writing,
the same pseudo register is translated to AC_VERB_SET_* automatically.
The AC_VERB_SET_AMP_* verb is re-encoded from the corresponding
AC_VERB_GET_AMP_* verb and parameter at writing.
Some verbs has a single command for read but multiple for writes. A
write for such a verb is split automatically to multiple verbs.
The patch provides also a few handy helper functions. They are
designed to be accessible even without regmap. When no regmap is set
up (e.g. before the codec device instantiation), the direct hardware
access is used. Also, it tries to avoid the unnecessary power-up.
The power up/down sequence is performed only on demand.
The codec driver needs to call snd_hdac_regmap_exit() and
snd_hdac_regmap_exit() at probe and remove if it wants the regmap
access.
There is one flag added to hdac_device. When the flag lazy_cache is
set, regmap helper ignores a write for a suspended device and returns
as if it was actually written. It reduces the hardware access pretty
much, e.g. when adjusting the mixer volume while in idle. This
assumes that the driver will sync the cache later at resume properly,
so use it carefully.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now let's take the basic tracepoints back to the HD-audio driver.
The three bus tracepoints, hda_send_cmd, hda_get_response and
hda_unsol_event are revived but in a slightly different form.
Since we don't assign the card number there, print the bus device name
instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the driver is unloaded before the codec is bound, it still keeps
the runtime PM refcount up, and results in the unbalance. This patch
covers these cases by introducing a flag indicating the runtime PM
initialization and handling the codec registration procedure more
properly. It also fixes the missing input beep device as a gratis,
too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add an overriding exec_verb op to struct hdac_device so that the call
via snd_hdac_exec_verb() can switch to a different route depending on
the setup. The codec driver sets this field so that it can handle the
errors or applying quirks appropriately. Furthermore, this mechanism
will be used for smooth transition for the regmap support in later
patches.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch changes the sysfs files assigned to the codec device on the
bus which were formerly identical with hwdep sysfs files. Now it
shows only a few core parameter, vendor_id, subsystem_id, revision_id,
afg, mfg, vendor_name and chip_name.
In addition, now a widget tree is added to the bus device sysfs
directory for showing the widget topology and attributes. It's just a
flat tree consisting of subdirectories named as the widget NID
including various attributes like widget capability bits. The AFG
(usually NID 0x01) is always found there, and it contains always
amp_in_caps, amp_out_caps and power_caps files. Each of these
attributes show a single value. The rest are the widget nodes
belonging to that AFG. Note that the child node might not start from
0x02 but from another value like 0x0a.
Each child node may contain caps, pin_caps, amp_in_caps, amp_out_caps,
power_caps and connections files. The caps (representing the widget
capability bits) always contain a value. The rest may contain
value(s) if the attribute exists on the node. Only connections file
show multiple values while other attributes have zero or one single
value.
An example of ls -R output is like below:
% ls -R /sys/bus/hdaudio/devices/hdaudioC0D0/
/sys/bus/hdaudio/devices/hdaudioC0D0/widgets/:
01/ 04/ 07/ 0a/ 0d/ 10/ 13/ 16/ 19/ 1c/ 1f/ 22/
02/ 05/ 08/ 0b/ 0e/ 11/ 14/ 17/ 1a/ 1d/ 20/ 23/
03/ 06/ 09/ 0c/ 0f/ 12/ 15/ 18/ 1b/ 1e/ 21/
/sys/bus/hdaudio/devices/hdaudioC0D0/widgets/01:
amp_in_caps amp_out_caps power_caps
/sys/bus/hdaudio/devices/hdaudioC0D0/widgets/02:
amp_in_caps amp_out_caps caps connections pin_caps pin_cfg
power_caps
/sys/bus/hdaudio/devices/hdaudioC0D0/widgets/03:
.....
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now some codes and functionalities of hda_codec struct are moved to
hdac_device struct. A few basic attributes like the codec address,
vendor ID number, FG numbers, etc are moved to hdac_device, and they
are accessed like codec->core.addr. The basic verb exec functions are
moved, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few basic codes for communicating over HD-audio bus are moved to
struct hdac_bus now. It has only command and get_response ops in
addition to the unsolicited event handling.
Note that the codec-side tracing support is disabled temporarily
during this transition due to the code shuffling. It will be
re-enabled later once when all pieces are settled down.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Define the common hd-audio driver and device types to bind over
snd_hda_bus_type publicly. This allows to implement other type of
device and driver code over hd-audio bus.
Now both struct hda_codec and struct hda_codec_driver inherit these
new struct hdac_device and struct hdac_driver, respectively.
The bus registration is done in subsys_initcall() to assure it
before any other driver registrations.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai