This reverts commit 410bd754cd.
The reverted commit had added a retry mechanism to the command entry
index allocation. The previous patch ensures that there is a free
command entry index once the command work handler holds the command
semaphore. Thus the retry mechanism is not needed.
Fixes: 410bd754cd ("net/mlx5: Add retry mechanism to the command entry index allocation")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Avoid a race where command work handler may fail to allocate command
entry index, by holding the command semaphore down till command entry
index is being freed.
Fixes: 410bd754cd ("net/mlx5: Add retry mechanism to the command entry index allocation")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently during NIC profile disablement all VXLAN udp ports offloaded to the
HW are flushed and during its enablement the driver send notification to
the stack to inform the core that the entire UDP tunnel port state has been
lost, uplink representor doesn't have the same behavior which can cause
VXLAN udp ports offload to be in bad state while moving between modes while
VXLAN interface exist.
Fixed by aligning the uplink representor profile behavior to the NIC behavior.
Fixes: 84db661247 ("net/mlx5e: Move set vxlan nic info to profile init")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Even when SF devices are supported, the SF device table allocation
can still fail.
In such case mlx5_sf_dev_supported still reports true, but SF device
table is invalid. This can result in NULL table access.
Hence, fix it by adding NULL table check.
Fixes: 1958fc2f07 ("net/mlx5: SF, Add auxiliary device driver")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Tunnel device follows RFC 6040, and during decapsulation inner
ip_ecn might change depending on inner and outer ip_ecn as follows:
+---------+----------------------------------------+
|Arriving | Arriving Outer Header |
| Inner +---------+---------+---------+----------+
| Header | Not-ECT | ECT(0) | ECT(1) | CE |
+---------+---------+---------+---------+----------+
| Not-ECT | Not-ECT | Not-ECT | Not-ECT | <drop> |
| ECT(0) | ECT(0) | ECT(0) | ECT(1) | CE* |
| ECT(1) | ECT(1) | ECT(1) | ECT(1)* | CE* |
| CE | CE | CE | CE | CE |
+---------+---------+---------+---------+----------+
Cells marked above are changed from original inner packet ip_ecn value.
Tc then matches on the modified inner ip_ecn, but hw offload which
matches the inner ip_ecn value before decap, will fail.
Fix that by mapping all the cases of outer and inner ip_ecn matching,
and only supporting cases where we know inner wouldn't be changed by
decap, or in the outer ip_ecn=CE case, inner ip_ecn didn't matter.
Fixes: bcef735c59 ("net/mlx5e: Offload TC matching on tos/ttl for ip tunnels")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Eli Cohen <elic@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
This reverts commit 54e1217b90.
Although the NIC doesn't support offload of outer header CSUM, using
gso_partial_features allows offloading the tunnel's segmentation. The
driver relies on the stack CSUM calculation of the outer header. For
this, NETIF_F_GSO_GRE_CSUM must be a member of the device's features.
Fixes: 54e1217b90 ("net/mlx5e: Block offload of outer header csum for GRE tunnel")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
This reverts commit 6d6727dddc.
Although the NIC doesn't support offload of outer header CSUM, using
gso_partial_features allows offloading the tunnel's segmentation. The
driver relies on the stack CSUM calculation of the outer header. For
this, NETIF_F_GSO_UDP_TUNNEL_CSUM must be a member of the device's
features.
Fixes: 6d6727dddc ("net/mlx5e: Block offload of outer header csum for UDP tunnels")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Routes with nexthop objects is currently not supported by multipath offload
and any attempts to use it is blocked, however this also block adding SW
routes with nexthop.
Resolve this by returning NOTIFY_DONE instead of an error which will allow such
a route to be created in SW but not offloaded.
This fix also solve an issue which block adding such routes on different devices
due to missing check if the route FIB device is one of multipath devices.
Fixes: 6a87afc072 ("mlx5: Fail attempts to use routes with nexthop objects")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Driver initiates DMA sync, hence it may skip CPU sync. Add
DMA_ATTR_SKIP_CPU_SYNC as input attribute both to dma_map_page and
dma_unmap_page to avoid redundant sync with the CPU.
When forcing the device to work with SWIOTLB, the extra sync might cause
data corruption. The driver unmaps the whole page while the hardware
used just a part of the bounce buffer. So syncing overrides the entire
page with bounce buffer that only partially contains real data.
Fixes: bc77b240b3 ("net/mlx5e: Add fragmented memory support for RX multi packet WQE")
Fixes: db05815b36 ("net/mlx5e: Add XSK zero-copy support")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The rep legacy RQ completion handling was missing the appropriate
handling of error CQEs (dump the CQE and queue a recover work), fix it
by calling trigger_report() when needed.
Since all CQE handling flows do the exact same error CQE handling,
extract it to a common helper function.
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Remove redundant and trivial error logging when trying to
offload mirred device with unsupported devices.
Using OVS could hit those a lot and the errors are still
logged in extack.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Feature dependencies should be resolved in fix features rather than in
set features flow. Move the check that disables HW-GRO in case CQE
compression is enabled from set_feature_hw_gro() to
mlx5e_fix_features().
Signed-off-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Remove redundant space when constructing the feature's enum. Validate
against the indented enum value.
Fixes: 6c72cb05d4 ("net/mlx5e: Use bitmap field for profile features")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When using libvirt to passthrough VF to VM it will always set the VF vlan
to 0 even if user didn’t request it, this will cause libvirt to fail to
boot in case the PF isn't eswitch owner.
Example of such case is the DPU host PF which isn't eswitch manager, so
any attempt to passthrough VF of it using libvirt will fail.
Fix it by not returning error in case set VF vlan is called with vid 0.
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add FEC counters' statistics of corrected_blocks and
uncorrectable_blocks, along with their lanes via ethtool.
HW supports corrected_blocks and uncorrectable_blocks counters both for
RS-FEC mode and FC-FEC mode. In FC mode these counters are accumulated
per lane, while in RS mode the correction method crosses lanes, thus
only total corrected_blocks and uncorrectable_blocks are reported in
this mode.
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
log_max_qp in driver's default profile #2 was set to 18, but FW actually
supports 17 at the most - a situation that led to the concerning print
when the driver is loaded:
"log_max_qp value in current profile is 18, changing to HCA capabaility
limit (17)"
The expected behavior from mlx5_profile #2 is to match the maximum FW
capability in regards to log_max_qp. Thus, log_max_qp in profile #2 is
initialized to a defined static value (0xff) - which basically means that
when loading this profile, log_max_qp value will be what the currently
installed FW supports at most.
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently all SFs are using the same CPUs. Spreading SF over CPUs, in
round-robin manner, in order to achieve better distribution of the SFs
over available CPUs.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently IRQs are requested one by one. To balance spreading IRQs
among cpus using such scheme requires remembering cpu mask for the
cpus used for a given device. This complicates the IRQ allocation
scheme in subsequent patch.
Hence, prepare the code for bulk IRQs allocation. This enables
spreading IRQs among cpus in subsequent patch.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The downstream patches add more functionality to irq_pool_affinity.
Move the irq_pool_affinity logic to a new file in order to ease the
coding and maintenance of it.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Move affinity binding of the IRQ to irq_request function in order to
bind the IRQ before inserting it to the xarray.
After this change, the IRQ is ready for use when inserted to the xarray.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently, IRQ layer have a separate flow for ctrl and comp IRQs, and
the distinction between ctrl and comp IRQs is done in the IRQ layer.
In order to ease the coding and maintenance of the IRQ layer,
introduce a new API for requesting control IRQs -
mlx5_ctrl_irq_request(struct mlx5_core_dev *dev).
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Callers of this functions ignore its return value, as reported by
Wang Qing, in one of the return paths, it returns positive values.
Since return value is ignored anyways, void out the return type of the
function.
Reported-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
In preparation for using blake2s in the RNG, we change the way that it
is wired-in to the build system. Instead of using ifdefs to select the
right symbol, we use weak symbols. And because ARM doesn't need the
generic implementation, we make the generic one default only if an arch
library doesn't need it already, and then have arch libraries that do
need it opt-in. So that the arch libraries can remain tristate rather
than bool, we then split the shash part from the glue code.
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: linux-kbuild@vger.kernel.org
Cc: linux-crypto@vger.kernel.org
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
kfree() and bitmap_free() are the same. But using the latter is more
consistent when freeing memory allocated with bitmap_zalloc().
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When a bitmap is local to a function, it is safe to use the non-atomic
__[set|clear]_bit(). No concurrent accesses can occur.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The 'possible_idx' bitmap is set just after it is zeroed, so we can save
the first step.
The 'free_idx' bitmap is used only at the end of the function as the
result of a bitmap xor operation. So there is no need to explicitly
zero it before.
So, slightly simply the code and remove 2 useless 'bitmap_zero()' call
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In current switchdev implementation, every VF PR is assigned to
individual ring on switchdev ctrl VSI. For slow-path traffic, there
is a mapping VF->ring done in software based on src_vsi value (by
calling ice_eswitch_get_target_netdev function).
With this change, HW solution is introduced which is more
efficient. For each VF, src MAC (VF's MAC) filter will be created,
which forwards packets to the corresponding switchdev ctrl VSI queue
based on src MAC address.
This filter has to be removed and then replayed in case of
resetting one VF. Keep information about this rule in repr->mac_rule,
thanks to that we know which rule has to be removed and replayed
for a given VF.
In case of CORE/GLOBAL all rules are removed
automatically. We have to take care of readding them. This is done
by ice_replay_vsi_adv_rule.
When driver leaves switchdev mode, remove all advanced rules
from switchdev ctrl VSI. This is done by ice_rem_adv_rule_for_vsi.
Flag repr->rule_added is needed because in some cases reset
might be triggered before VF sends request to add MAC.
Co-developed-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
ice_replay_vsi_adv_rule will replay advanced rules for a given VSI.
Exit this function when list of rules for given recipe is empty.
Do not add rule when given vsi_handle does not match vsi_handle
from the rule info.
Use ICE_MAX_NUM_RECIPES instead of ICE_SW_LKUP_LAST in order to find
advanced rules as well.
Signed-off-by: Victor Raj <victor.raj@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As the possible failure of the allocation, the devm_ioremap() may return
NULL pointer.
Take tgec_initialization() as an example.
If allocation fails, the params->base_addr will be NULL pointer and will
be assigned to tgec->regs in tgec_config().
Then it will cause the dereference of NULL pointer in set_mac_address(),
which is called by tgec_init().
Therefore, it should be better to add the sanity check after the calling
of the devm_ioremap().
Fixes: 3933961682 ("fsl/fman: Add FMan MAC driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Laurent reported that they have seen a significant amount of TCP retransmissions
at high throughput from applications residing in network namespaces talking to
the outside world via veths. The drops were seen on the qdisc layer (fq_codel,
as per systemd default) of the phys device such as ena or virtio_net due to all
traffic hitting a _single_ TX queue _despite_ multi-queue device. (Note that the
setup was _not_ using XDP on veths as the issue is generic.)
More specifically, after edbea92202 ("veth: Store queue_mapping independently
of XDP prog presence") which made it all the way back to v4.19.184+,
skb_record_rx_queue() would set skb->queue_mapping to 1 (given 1 RX and 1 TX
queue by default for veths) instead of leaving at 0.
This is eventually retained and callbacks like ena_select_queue() will also pick
single queue via netdev_core_pick_tx()'s ndo_select_queue() once all the traffic
is forwarded to that device via upper stack or other means. Similarly, for others
not implementing ndo_select_queue() if XPS is disabled, netdev_pick_tx() might
call into the skb_tx_hash() and check for prior skb_rx_queue_recorded() as well.
In general, it is a _bad_ idea for virtual devices like veth to mess around with
queue selection [by default]. Given dev->real_num_tx_queues is by default 1,
the skb->queue_mapping was left untouched, and so prior to edbea92202 the
netdev_core_pick_tx() could do its job upon __dev_queue_xmit() on the phys device.
Unbreak this and restore prior behavior by removing the skb_record_rx_queue()
from veth_xmit() altogether.
If the veth peer has an XDP program attached, then it would return the first RX
queue index in xdp_md->rx_queue_index (unless configured in non-default manner).
However, this is still better than breaking the generic case.
Fixes: edbea92202 ("veth: Store queue_mapping independently of XDP prog presence")
Fixes: 638264dc90 ("veth: Support per queue XDP ring")
Reported-by: Laurent Bernaille <laurent.bernaille@datadoghq.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Cc: Toshiaki Makita <toshiaki.makita1@gmail.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Toshiaki Makita <toshiaki.makita1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are currently 2 ways to create a set of sysfs files for a
kobj_type, through the default_attrs field, and the default_groups
field. Move the ibmveth sysfs code to use default_groups
field which has been the preferred way since aa30f47cf6 ("kobject: Add
support for default attribute groups to kobj_type") so that we can soon
get rid of the obsolete default_attrs field.
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Cristobal Forno <cforno12@linux.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code is holding the &ofdpa->flow_tbl_lock spinlock so it is not
allowed to sleep. That means we have to pass the OFDPA_OP_FLAG_NOWAIT
flag to ofdpa_flow_tbl_del().
Fixes: 936bd48656 ("rocker: use FIB notifications instead of switchdev calls")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean the following coccicheck warning:
./drivers/net/ethernet/sfc/efx_channels.c:870:36-37: WARNING opportunity
for swap().
./drivers/net/ethernet/sfc/efx_channels.c:824:36-37: WARNING opportunity
for swap().
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the PCS selection to use mac_select_pcs, which allows the PCS
to perform any validation it needs.
We must use separate phylink_pcs instances for the USX and SGMII PCS,
rather than just changing the "ops" pointer before re-setting it to
phylink as this interface queries the PCS, rather than requesting it
to be changed.
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems pretty clear ppp layer assumed user space
would always be kind to provide enough data
in their write() to a ppp device.
This patch makes sure user provides at least
2 bytes.
It adds PPP_PROTO_LEN macro that could replace
in net-next many occurrences of hard-coded 2 value.
I replaced only one occurrence to ease backports
to stable kernels.
The bug manifests in the following report:
BUG: KMSAN: uninit-value in ppp_send_frame+0x28d/0x27c0 drivers/net/ppp/ppp_generic.c:1740
ppp_send_frame+0x28d/0x27c0 drivers/net/ppp/ppp_generic.c:1740
__ppp_xmit_process+0x23e/0x4b0 drivers/net/ppp/ppp_generic.c:1640
ppp_xmit_process+0x1fe/0x480 drivers/net/ppp/ppp_generic.c:1661
ppp_write+0x5cb/0x5e0 drivers/net/ppp/ppp_generic.c:513
do_iter_write+0xb0c/0x1500 fs/read_write.c:853
vfs_writev fs/read_write.c:924 [inline]
do_writev+0x645/0xe00 fs/read_write.c:967
__do_sys_writev fs/read_write.c:1040 [inline]
__se_sys_writev fs/read_write.c:1037 [inline]
__x64_sys_writev+0xe5/0x120 fs/read_write.c:1037
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x54/0xd0 arch/x86/entry/common.c:82
entry_SYSCALL_64_after_hwframe+0x44/0xae
Uninit was created at:
slab_post_alloc_hook mm/slab.h:524 [inline]
slab_alloc_node mm/slub.c:3251 [inline]
__kmalloc_node_track_caller+0xe0c/0x1510 mm/slub.c:4974
kmalloc_reserve net/core/skbuff.c:354 [inline]
__alloc_skb+0x545/0xf90 net/core/skbuff.c:426
alloc_skb include/linux/skbuff.h:1126 [inline]
ppp_write+0x11d/0x5e0 drivers/net/ppp/ppp_generic.c:501
do_iter_write+0xb0c/0x1500 fs/read_write.c:853
vfs_writev fs/read_write.c:924 [inline]
do_writev+0x645/0xe00 fs/read_write.c:967
__do_sys_writev fs/read_write.c:1040 [inline]
__se_sys_writev fs/read_write.c:1037 [inline]
__x64_sys_writev+0xe5/0x120 fs/read_write.c:1037
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x54/0xd0 arch/x86/entry/common.c:82
entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linux-ppp@vger.kernel.org
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can increase the efficiency of rx path by using buffers to receive
packets then build SKBs around them just before passing into the network
stack. In contrast, preallocating SKBs too early reduces CPU cache
efficiency.
NAT Performance results on BT Home Hub 5A (kernel 5.10.89, mtu 1500):
Down Up
Before 577 Mbps 648 Mbps
After 624 Mbps 695 Mbps
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
NAT Performance results on BT Home Hub 5A (kernel 5.10.89, mtu 1500):
Down Up
Before 545 Mbps 625 Mbps
After 577 Mbps 648 Mbps
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEK3kIWJt9yTYMP3ehqclaivrt76kFAmHWBHkTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRCpyVqK+u3vqaY0CACb2NOHCl09a20N6REAmKzdXEq6LO0C
52fSdeAhRffWh7GqlQED7+XgzuGimsQ5DYWMzP1dzCCVuI/f1gZwrMKJU/e3rZjE
wR9VgIwTUulauW1KMUz/R8qJP5R7xq5wKXflm9iPcDo7buzTDf441vTt8WhQILIB
ajl94ZSzhpy4yNk+YBJObanMALRTSjBPrIlEjzDdsex/IjkPDkTm8NYe7SRWzMf3
UQR6rEAIecKBwnl0Q3bwcOU5GL8j333Xem2bxDsnm93tjfBwEtBfBX6XM1UX2B2L
9WooLHmJHibkmp/1vNMzlGvi9crdTrMhWnFweTaAsr29yG3JZ4r2PytO
=bCV1
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-5.16-20220105' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2022-01-05
It consists of 2 patches, both by me. The first one fixes the use of
an uninitialized variable in the gs_usb driver the other one a
skb_over_panic in the ISOTP stack in case of reception of too large
ISOTP messages.
* tag 'linux-can-fixes-for-5.16-20220105' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: isotp: convert struct tpcon::{idx,len} to unsigned int
can: gs_usb: fix use of uninitialized variable, detach device on reception of invalid USB data
====================
Link: https://lore.kernel.org/r/20220105205443.1274709-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The received data contains the channel the received data is associated
with. If the channel number is bigger than the actual number of
channels assume broken or malicious USB device and shut it down.
This fixes the error found by clang:
| drivers/net/can/usb/gs_usb.c:386:6: error: variable 'dev' is used
| uninitialized whenever 'if' condition is true
| if (hf->channel >= GS_MAX_INTF)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
| drivers/net/can/usb/gs_usb.c:474:10: note: uninitialized use occurs here
| hf, dev->gs_hf_size, gs_usb_receive_bulk_callback,
| ^~~
Link: https://lore.kernel.org/all/20211210091158.408326-1-mkl@pengutronix.de
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The four RGMII interface modes take care of the required RGMII delay
configuration at the PHY and should not be limited by the network MAC
driver. Sadly, gemini was only permitting RGMII mode with no delays,
which would require the required delay to be inserted via PCB tracking
or by the MAC.
However, there are designs that require the PHY to add the delay, which
is impossible without Gemini permitting the other three PHY interface
modes. Fix the driver to allow these.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Link: https://lore.kernel.org/r/E1n4mpT-002PLd-Ha@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Corentin Labbe reports that the SSI 1328 does not work when allowing
the PHY to operate at gigabit speeds, but does work with the generic
PHY driver.
This appears to be because m88e1118_config_init() writes a fixed value
to the MSCR register, claiming that this is to enable 1G speeds.
However, this always sets bits 4 and 5, enabling RGMII transmit and
receive delays. The suspicion is that the original board this was
added for required the delays to make 1G speeds work.
Add the necessary configuration for RGMII delays for the 88E1118 to
bring this into line with the requirements for RGMII support, and thus
make the SSI 1328 work.
Corentin Labbe has tested this on gemini-ssi1328 and gemini-ns2502.
Reported-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use phy_write_paged() in m88e1118_config_init() to set the MSCR value.
We leave the other paged write for the LEDs in case the DT register
parsing is relying on this page.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit f77b83b5bb.
This change breaks multiple usb to ethernet dongles attached on Lenovo
USB hub.
Fixes: f77b83b5bb ("net: usb: r8152: Add MAC passthrough support for more Lenovo Docks")
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Link: https://lore.kernel.org/r/20220105155102.8557-1-aaron.ma@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stefan Schmidt says:
====================
pull-request: ieee802154 for net 2022-01-05
Below I have a last minute fix for the atusb driver.
Pavel fixes a KASAN uninit report for the driver. This version is the
minimal impact fix to ease backporting. A bigger rework of the driver to
avoid potential similar problems is ongoing and will come through net-next
when ready.
* tag 'ieee802154-for-net-2022-01-05' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan:
ieee802154: atusb: fix uninit value in atusb_set_extended_addr
====================
Link: https://lore.kernel.org/r/20220105153914.512305-1-stefan@datenfreihafen.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Locally generated packets ingress the device through its CPU port. When
the CPU port is congested and there are not enough credits in its
headroom buffer, packets can be dropped.
While this might be acceptable for data packets that traverse the
network, configuration packets exchanged between the host and the device
(EMADs) should not be subjected to this flow control.
The "sdq_lp" bit in the SDQ (Send Descriptor Queue) context allows the
host to instruct the device to treat packets sent on this queue as
"local processing" and always process them, regardless of the state of
the CPU port's headroom.
Add the definition of this bit and set it for the dedicated SDQ reserved
for the transmission of EMAD packets. This makes the "local processing"
bit in the WQE (Work Queue Element) redundant, so clear it.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEK3kIWJt9yTYMP3ehqclaivrt76kFAmHVfO4THG1rbEBwZW5n
dXRyb25peC5kZQAKCRCpyVqK+u3vqYYCB/9lWoCLyk6woA7RY3Td/SWvgG58p3i4
Zew/bJmL5j9QJiAdZtYTORGysVnA/itr9rlKHGS5dqrPupIpZOAP5BtRoSsTDNjD
7Mj2aAGACsl5CY5b5Q3Y/OBEt+RFMThrWpJwnh0wcLRYsfg1GWa5R9vo3cgLeUl2
wdTpDzC6oRAvpo6iMzvzFyTS/CqBigArNiGt29XMXI3uDeCTqdNnxVqpVMrt8jK1
DVNp4Xy40fY9IwuGmhpHm7h0xK0YCneEKsKnf+aTKLcC2fYkWof1pgU3TbQwNYAH
M6Gw4XC4wAsEPT9yRjrc6VoH6BBtOl0ZGglUJkub7L58CVD6MOPT1aUp
=zIRd
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-5.17-20220105' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2022-01-05
this is a pull request of 15 patches for net-next/master.
The first patch is by me and removed an unused variable from the
usb_8dev driver.
Andy Shevchenko contributes a patch for the mcp251x driver, which
removes an unneeded assignment.
Jimmy Assarsson's patch for the kvaser_usb makes use of units.h in the
assignment of frequencies.
Lad Prabhakar provides 2 patches, converting the ti_hecc and the
sja1000 driver to make use of platform_get_irq().
The 10 remaining patches are by Vincent Mailhol. First the etas_es58x
driver populates the net_device::dev_port. The next 5 patches cleanup
the handling of CAN error and CAN RTR messages of all drivers. The
remaining 4 patches enhance the CAN controller mode flag handling and
export it via netlink to user space.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently PF and VF use two sets of command code for modules to interact
with firmware. These codes values are same espect the macro names. It is
redundent to keep two sets of command code for same functions between PF
and VF.
So this patch firstly creates a unified command code for PF and VF module.
We keep the macro name same with the PF command code name to avoid too many
meaningless modifications. Secondly the new common command codes are used
to replace the old ones in VF and deletes the old ones.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch firstly uses new tqp struct(hclge_comm_tqp) and removes the
old VF tqp struct(hclgevf_tqp). All the tqp stats members used in VF module
are modified according to the new hclge_comm_tqp.
Secondly VF tqp stats APIs are refactored to use new common tqp stats APIs.
The old tqp stats APIs in VF are deleted.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch firstly uses new tqp struct(hclge_comm_tqp) and deletes the
old PF tqp struct(hclge_tqp). All the tqp stats members used in PF module
are modified according to the new hclge_comm_tqp.
Secondly PF tqp stats APIs are refactored to use new common tqp stats APIs.
The old tqp stats APIs in PF are deleted.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch creates new set of common tqp stats structures and APIs for PF
and VF tqp stats module. Subfunctions such as get tqp stats, update tqp
stats and reset tqp stats are inclued in this patch.
These new common tqp stats APIs will be used to replace the old PF and VF
tqp stats APIs in next patches.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses common rss init APIs to replace the old APIs in VF rss
module and removes the old VF rss init APIs. Several related Subfunctions
and macros are also modified in this patch.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses common rss init APIs to replace the old APIs in PF rss
module and deletes the old PF rss init APIs. Some related subfunctions and
macros are also modified in this patch.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch creates new set of common rss init APIs for PF and VF rss
module. Subfunctions called by rss init process are also created include
rss tuple configuration and rss indirect table configuration.
These new common rss init APIs will be used to replace the old PF and VF
rss init APIs in next patches.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses new common rss set APIs to replace the old APIs in VF rss
module and removes those old rss set APIs. The related macros in VF are
also modified.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses new common rss set APIs to replace the old APIs in PF rss
module and deletes the old rss set APIs. The related macros are also
modified.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, hns3 PF and VF rss module have two sets of rss set APIs to
configure rss. There is no need to keep two sets of these same APIs.
So this patch creates new set of common rss set APIs for PF and VF reuse.
These new APIs will be used to unify old APIs in next patches.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch firstly uses new rss parameter struct(hclge_comm_rss_cfg) as
child member of hclgevf_dev and deletes the original child rss parameter
member(hclgevf_rss_cfg). All the rss parameter members used in VF rss
module is modified according to the new hclge_comm_rss_cfg.
Secondly VF rss get APIs are refactored to use new common rss get APIs. The
old rss get APIs in VF are deleted.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch firstly uses new rss parameter struct(hclge_comm_rss_cfg) as
child member of hclge_dev and deletes the original child rss parameter
members in vport. All the vport child rss parameter members used in PF rss
module is modified according to the new hclge_comm_rss_cfg.
Secondly PF rss get APIs are refactored to use new common rss get APIs. The
old rss get APIs in PF are deleted.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PF and VF rss get APIs are almost the same espect the suffixes of API
names. These same impementions bring double development and bugfix work.
So this patch creates new common rss get APIs for PF and VF rss module.
Subfunctions called by rss query process are also created(e.g. rss tuple
conversion APIs).
These new common rss get APIs will be used to replace PF and VF old rss
APIs in next patches.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, there are two different sets of special command codes in PF and
VF cmdq modules, this is because VF driver only uses small part of all the
command codes. In other words, these not used command codes in VF are also
sepcial command codes theoretically.
So this patch unifes the special command codes and deletes the bool param
is_pf of hclge_comm_send. All the related functions are refactored
according to the new hclge_comm_send function prototype.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently PF stores its rss parameters in vport structure. VF stores rss
configurations in hclgevf_rss_cfg structure. Actually hns3 rss parameters
are same beween PF and VF. The two set of rss parameters are redundent and
may add extra bugfix work.
So this patch creates new common rss parameter struct(hclge_comm_rss_cfg)
to unify PF and VF rss configurations.
These new structures will be used to unify rss configurations in PF and VF
rss APIs in next patches.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend lan966x driver with mdb support by implementing the switchdev
calls: SWITCHDEV_OBJ_ID_PORT_MDB and SWITCHDEV_OBJ_ID_HOST_MDB.
It is allowed to add both ipv4/ipv6 entries and l2 entries. To add
ipv4/ipv6 entries is not required to use the PGID table while for l2
entries it is required. The PGID table is much smaller than MAC table
so only fewer l2 entries can be added.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first entries in the PGID table are used by the front ports while
the last entries are used for different purposes like flooding mask,
copy to CPU, etc. So add these macros to define which entries can be
used for general purpose.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend mac functionality with the function lan966x_mac_ip_learn. This
function adds an entry in the MAC table for IP multicast addresses.
These entries can copy a frame to the CPU but also can forward on the
front ports.
This functionality is needed for mdb support. In case the CPU and some
of the front ports subscribe to an IP multicast address.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement read and write access to IEEE 802.3 Clause 45 Ethernet
phy registers while making use of new mdiobus_c45_regad and
mdiobus_c45_devad helpers.
Tested on the Ubiquiti UniFi 6 LR access point featuring
MediaTek MT7622BV WiSoC with Aquantia AQR112C.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of returning -1 (-EPERM) when MDIO bus is stuck busy
while writing or 0xffff if it happens while reading, return the
appropriate -ETIMEDOUT. Also fix return type to int instead of u32.
Refactor functions to use bitfield helpers instead of having various
masking and shifting constants in the code, which also results in the
register definitions in the header file being more obviously related
to what is stated in the MediaTek's Reference Manual.
Fixes: 656e705243 ("net-next: mediatek: add support for MT7623 ethernet")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-01-04
This series contains updates to i40e and iavf drivers.
Mateusz adjusts displaying of failed VF MAC message when the failure is
expected as well as modifying an NVM info message to not confuse the user
for i40e.
Di Zhu fixes a use-after-free issue MAC filters for i40e.
Jedrzej fixes an issue with misreporting of Rx and Tx queues during
reinitialization for i40e.
Karen correct checking of channel queue configuration to occur against
active queues for iavf.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the CAN netlink interface provides no easy ways to check
the capabilities of a given controller. The only method from the
command line is to try each CAN_CTRLMODE_* individually to check
whether the netlink interface returns an -EOPNOTSUPP error or not
(alternatively, one may find it easier to directly check the source
code of the driver instead...)
This patch introduces a method for the user to check both the
supported and the static capabilities. The proposed method introduces
a new IFLA nest: IFLA_CAN_CTRLMODE_EXT which extends the current
IFLA_CAN_CTRLMODE. This is done to guaranty a full forward and
backward compatibility between the kernel and the user land
applications.
The IFLA_CAN_CTRLMODE_EXT nest contains one single entry:
IFLA_CAN_CTRLMODE_SUPPORTED. Because this entry is only used in one
direction: kernel to userland, no new struct nla_policy are
introduced.
Below table explains how IFLA_CAN_CTRLMODE_SUPPORTED (hereafter:
"supported") and can_ctrlmode::flags (hereafter: "flags") allow us to
identify both the supported and the static capabilities, when masked
with any of the CAN_CTRLMODE_* bit flags:
supported & flags & Controller capabilities
CAN_CTRLMODE_* CAN_CTRLMODE_*
-----------------------------------------------------------------------
false false Feature not supported (always disabled)
false true Static feature (always enabled)
true false Feature supported but disabled
true true Feature supported and enabled
Link: https://lore.kernel.org/all/20211213160226.56219-5-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Previous patch removed can_priv::ctrlmode_static to replace it with
can_get_static_ctrlmode().
A condition sine qua non for this to work is that the controller
static modes should never be set in can_priv::ctrlmode_supported
(c.f. the comment on can_priv::ctrlmode_supported which states that it
is for "options that can be *modified* by netlink"). Also, this
condition is already correctly fulfilled by all existing drivers
which rely on the ctrlmode_static feature.
Nonetheless, we added an extra safeguard in can_set_static_ctrlmode()
to return an error value and to warn the developer who would be
adventurous enough to set to static a given feature that is already
set to supported.
The drivers which rely on the static controller mode are then updated
to check the return value of can_set_static_ctrlmode().
Link: https://lore.kernel.org/all/20211213160226.56219-3-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The statically enabled features of a CAN controller can be retrieved
using below formula:
| u32 ctrlmode_static = priv->ctrlmode & ~priv->ctrlmode_supported;
As such, there is no need to store this information. This patch remove
the field ctrlmode_static of struct can_priv and provides, in
replacement, the inline function can_get_static_ctrlmode() which
returns the same value.
Link: https://lore.kernel.org/all/20211213160226.56219-2-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The actual payload length of the CAN Remote Transmission Request (RTR)
frames is always 0, i.e. no payload is transmitted on the wire.
However, those RTR frames still use the DLC to indicate the length of
the requested frame.
As such, net_device_stats::tx_bytes should not be increased when
sending RTR frames.
The function can_get_echo_skb() already returns the correct length,
even for RTR frames (c.f. [1]). However, for historical reasons, the
drivers do not use can_get_echo_skb()'s return value and instead, most
of them store a temporary length (or dlc) in some local structure or
array. Using the return value of can_get_echo_skb() solves the
issue. After doing this, such length/dlc fields become unused and so
this patch does the adequate cleaning when needed.
This patch fixes all the CAN drivers.
Finally, can_get_echo_skb() is decorated with the __must_check
attribute in order to force future drivers to correctly use its return
value (else the compiler would emit a warning).
[1] commit ed3320cec2 ("can: dev: __can_get_echo_skb():
fix real payload length return value for RTR frames")
Link: https://lore.kernel.org/all/20211207121531.42941-6-mailhol.vincent@wanadoo.fr
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Yasushi SHOJI <yashi@spacecubics.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: Andreas Larsson <andreas@gaisler.com>
Tested-by: Jimmy Assarsson <extja@kvaser.com> # kvaser
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Acked-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Tested-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
[mkl: add conversion for grcan]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The actual payload length of the CAN Remote Transmission Request (RTR)
frames is always 0, i.e. no payload is transmitted on the wire.
However, those RTR frames still use the DLC to indicate the length of
the requested frame.
As such, net_device_stats::rx_bytes should not be increased for the
RTR frames.
This patch fixes all the CAN drivers.
Link: https://lore.kernel.org/all/20211207121531.42941-5-mailhol.vincent@wanadoo.fr
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Yasushi SHOJI <yashi@spacecubics.com>
Cc: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Cc: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Jimmy Assarsson <extja@kvaser.com> # kvaser
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Acked-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Tested-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The actual payload length of the CAN Remote Transmission Request (RTR)
frames is always 0, i.e. no payload is transmitted on the wire.
However, those RTR frames still use the DLC to indicate the length of
the requested frame.
For this reason, it is incorrect to copy the payload of RTR frames
(the payload buffer would only contain garbage data). This patch
encapsulates the payload copy in a check toward the RTR flag.
Link: https://lore.kernel.org/all/20211207121531.42941-4-mailhol.vincent@wanadoo.fr
Cc: Yasushi SHOJI <yashi@spacecubics.com>
Tested-by: Yasushi SHOJI <yashi@spacecubics.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CAN error message frames (i.e. error skb) are an interface
specific to socket CAN. The payload of the CAN error message frames
does not correspond to any actual data sent on the wire. Only an error
flag and a delimiter are transmitted when an error occurs (c.f. ISO
11898-1 section 10.4.4.2 "Error flag").
For this reason, it makes no sense to increment the tx_packets and
tx_bytes fields of struct net_device_stats when sending an error
message frame because no actual payload will be transmitted on the
wire.
N.B. Sending error message frames is a very specific feature which, at
the moment, is only supported by the Kvaser Hydra hardware. Please
refer to [1] for more details on the topic.
[1] https://lore.kernel.org/linux-can/CAMZ6RqK0rTNg3u3mBpZOoY51jLZ-et-J01tY6-+mWsM4meVw-A@mail.gmail.com/t/#u
Link: https://lore.kernel.org/all/20211207121531.42941-3-mailhol.vincent@wanadoo.fr
Co-developed-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CAN error message frames (i.e. error skb) are an interface
specific to socket CAN. The payload of the CAN error message frames
does not correspond to any actual data sent on the wire. Only an error
flag and a delimiter are transmitted when an error occurs (c.f. ISO
11898-1 section 10.4.4.2 "Error flag").
For this reason, it makes no sense to increment the rx_packets and
rx_bytes fields of struct net_device_stats because no actual payload
were transmitted on the wire.
This patch fixes all the CAN drivers.
Link: https://lore.kernel.org/all/20211207121531.42941-2-mailhol.vincent@wanadoo.fr
CC: Marc Kleine-Budde <mkl@pengutronix.de>
CC: Nicolas Ferre <nicolas.ferre@microchip.com>
CC: Alexandre Belloni <alexandre.belloni@bootlin.com>
CC: Ludovic Desroches <ludovic.desroches@microchip.com>
CC: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
CC: Maxime Ripard <mripard@kernel.org>
CC: Chen-Yu Tsai <wens@csie.org>
CC: Jernej Skrabec <jernej.skrabec@gmail.com>
CC: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
CC: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
CC: Michal Simek <michal.simek@xilinx.com>
CC: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Jimmy Assarsson <extja@kvaser.com> # kvaser
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Acked-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Tested-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The field dev_port of struct net_device indicates the port number of a
network device [1]. This patch populates this field.
This field can be helpful to distinguish between the two network
interfaces of a dual channel device (i.e. ES581.4 or ES582.1). Indeed,
at the moment, all the network interfaces of a same device share the
same static udev attributes c.f. output of:
| udevadm info --attribute-walk /sys/class/net/canX
The dev_port attribute can then be used to write some udev rules to,
for example, assign a permanent name to each network interface based
on the serial/dev_port pair (which is convenient when you have a test
bench with several CAN devices connected simultaneously and wish to
keep consistent interface names upon reboot).
[1] https://www.kernel.org/doc/Documentation/ABI/testing/sysfs-class-net
Link: https://lore.kernel.org/all/20211026180553.1953189-1-mailhol.vincent@wanadoo.fr
Suggested-by: Lukas Magel <lukas.magel@escrypt.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue when
using hierarchical interrupt domains using "interrupts" property in
the node as this bypasses the hierarchical setup and messes up the irq
chaining.
In preparation for removal of static setup of IRQ resource from DT
core code use platform_get_irq().
Link: https://lore.kernel.org/all/20211221194508.11737-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
GPIO library does copy the of_node from the parent device of the GPIO
chip, there is no need to repeat this in the individual drivers.
Remove assignment here.
For the details one may look into the of_gpio_dev_init()
implementation.
Link: https://lore.kernel.org/all/20211202205855.76946-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Depending on BIOS configuration IOSM driver exchanges
protocol required for putting device into D3L2 or D3L1.2.
ipc_pcie_suspend_s2idle() is implemented to put device to D3L1.2.
This patch forces PCI core know this device should stay at D0.
- pci_save_state()is expensive since it does a lot of slow PCI
config reads.
The reported issue is not observed on x86 platform. The supurios
wake on AMD platform needs to be futher debugged with orignal patch
submitter [1]. Also the impact of adding pci_save_state() needs to be
assessed by testing it on other platforms.
This reverts commit f4dd5174e273("net: wwan: iosm: Keep device
at D0 for s2idle case").
[1] https://lore.kernel.org/all/20211224081914.345292-2-kai.heng.feng@canonical.com/
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Link: https://lore.kernel.org/r/20220104150213.1894-1-m.chetan.kumar@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The RX page_ring is an optional feature that improves
performance. When allocation fails the driver can still
function, but possibly with a lower bandwidth.
Guard against dereferencing a NULL page_ring.
Fixes: 2768935a46 ("sfc: reuse pages to avoid DMA mapping/unmapping costs")
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Reported-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/164111288276.5798.10330502993729113868.stgit@palantir17.mph.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the absence of this validation, if the user requests to
configure queues more than the enabled queues, it results in
sending the requested number of queues to the kernel stack
(due to the asynchronous nature of VF response), in which
case the stack might pick a queue to transmit that is not
enabled and result in Tx hang. Fix this bug by
limiting the total number of queues allocated for VF to
active queues of VF.
Fixes: d5b33d0244 ("i40evf: add ndo_setup_tc callback to i40evf")
Signed-off-by: Ashwin Vijayavel <ashwin.vijayavel@intel.com>
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There was a wrong queues representation in sysfs during
driver's reinitialization in case of online cpus number is
less than combined queues. It was caused by stopped
NetworkManager, which is responsible for calling vsi_open
function during driver's initialization.
In specific situation (ex. 12 cpus online) there were 16 queues
in /sys/class/net/<iface>/queues. In case of modifying queues with
value higher, than number of online cpus, then it caused write
errors and other errors.
Add updating of sysfs's queues representation during driver
initialization.
Fixes: 41c445ff0f ("i40e: main driver core")
Signed-off-by: Lukasz Cieplicki <lukaszx.cieplicki@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When loading the i40e driver, it prints a message like: 'The driver for the
device detected a newer version of the NVM image v1.x than expected v1.y.
Please install the most recent version of the network driver.' This is
misleading as the driver is working as expected.
Fix that by removing the second part of message and changing it from
dev_info to dev_dbg.
Fixes: 4fb29bddb5 ("i40e: The driver now prints the API version in error message")
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Hide i40e opcode information sent during response to VF in case when
untrusted VF tried to change MAC on the VF interface.
This is implemented by adding an additional parameter 'hide' to the
response sent to VF function that hides the display of error
information, but forwards the error code to VF.
Previously it was not possible to send response with some error code
to VF without displaying opcode information.
Fixes: 5c3c48ac6b ("i40e: implement virtual device interface")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Alexander reported a use of uninitialized value in
atusb_set_extended_addr(), that is caused by reading 0 bytes via
usb_control_msg().
Fix it by validating if the number of bytes transferred is actually
correct, since usb_control_msg() may read less bytes, than was requested
by caller.
Fail log:
BUG: KASAN: uninit-cmp in ieee802154_is_valid_extended_unicast_addr include/linux/ieee802154.h:310 [inline]
BUG: KASAN: uninit-cmp in atusb_set_extended_addr drivers/net/ieee802154/atusb.c:1000 [inline]
BUG: KASAN: uninit-cmp in atusb_probe.cold+0x29f/0x14db drivers/net/ieee802154/atusb.c:1056
Uninit value used in comparison: 311daa649a2003bd stack handle: 000000009a2003bd
ieee802154_is_valid_extended_unicast_addr include/linux/ieee802154.h:310 [inline]
atusb_set_extended_addr drivers/net/ieee802154/atusb.c:1000 [inline]
atusb_probe.cold+0x29f/0x14db drivers/net/ieee802154/atusb.c:1056
usb_probe_interface+0x314/0x7f0 drivers/usb/core/driver.c:396
Fixes: 7490b008d1 ("ieee802154: add support for atusb transceiver")
Reported-by: Alexander Potapenko <glider@google.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/20220104182806.7188-1-paskripkin@gmail.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Return value from efx_mcdi_rpc() directly instead
of taking this in another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: CGEL ZTE <cgel.zte@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent bpf-next merge brought in header changes which uncovered
includes missing in net-next which were not present in bpf-next.
Build problems happen only on less-popular arches like hppa,
sparc, alpha etc.
I could repro the build problem with ice but not the mlx5 problem
Abdul was reporting. mlx5 does look like it should include filter.h,
anyway.
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Fixes: e63a023489 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next")
Link: https://lore.kernel.org/all/7c03768d-d948-c935-a7ab-b1f963ac7eed@linux.vnet.ibm.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for scatter gather DMA. DMA in PMAC splits
the packet into several buffers when the MTU on the CPU port is
less than the MTU of the switch. The first buffer starts at an
offset of NET_IP_ALIGN. In subsequent buffers, dma ignores the
offset. Thanks to this patch, the user can still connect to the
device in such a situation. For normal configurations, the patch
has no effect on performance.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for external timestamp and periodic signal output.
TJA1103 have one periodic signal and one external time stamp signal that
can be multiplexed on all 11 gpio pins.
The periodic signal can be only enabled or disabled. Have no start time
and if is enabled will be generated with a period of one second in sync
with the LTC seconds counter. The phase change is possible only with a
half of a second.
The external timestamp signal has no interrupt and no valid bit and
that's why the timestamps are handled by polling in .do_aux_work.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get originating device from tuple offload metadata match ingress_ifindex,
and set flow_source hint to either LOCAL for vf/sf reps, UPLINK for
uplink/wire/tunnel devices/bond, or ANY (as before this patch)
for all others.
This allows lower layer (software steering or firmware) to insert the tuple
rule only in one table (either rx or tx) instead of two (rx and tx).
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On systems with large numbers of MDIO bus/muxes the message indicating
that a given MDIO bus has been successfully probed is repeated for as
many buses we have, which can eat up substantial boot time for no
reason, demote to a debug print.
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220103194024.2620-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit b45396afa4 ("net: phy:
fixed_phy: Fix NULL vs IS_ERR() checking in __fixed_phy_register")
since it prevents any system that uses a fixed PHY without a GPIO
descriptor from properly working:
[ 5.971952] brcm-systemport 9300000.ethernet: failed to register fixed PHY
[ 5.978854] brcm-systemport: probe of 9300000.ethernet failed with error -22
[ 5.986047] brcm-systemport 9400000.ethernet: failed to register fixed PHY
[ 5.992947] brcm-systemport: probe of 9400000.ethernet failed with error -22
Fixes: b45396afa4 ("net: phy: fixed_phy: Fix NULL vs IS_ERR() checking in __fixed_phy_register")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220103193453.1214961-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use dma_set_mask_and_coherent() instead of unrolling it with some
dma_set_mask()+dma_set_coherent_mask().
Moreover, as stated in [1], dma_set_mask() with a 64-bit mask will never
fail if dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
That said, 'high_dma' can only be 1 after a successful
dma_set_mask_and_coherent().
Simplify code and remove some dead code accordingly, including a now
useless parameter to vxge_device_register().
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dma_set_mask_and_coherent() instead of unrolling it with some
dma_set_mask()+dma_set_coherent_mask().
Moreover, as stated in [1], dma_set_mask() with a 64-bit mask will never
fail if dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
That said, 'dma_flag' can only be 'true' after a successful
dma_set_mask_and_coherent().
Simplify code and remove some dead code accordingly, including the now
useless 'high_dma_flag' field in 'struct s2io_nic'.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sorry for being rude but new vendors/drivers are supposed to be disabled
by default, otherwise we will have to manually keep track of all vendors
we are not interested in building.
Fixes: 2f207cbf0d ("net: vertexcom: Add MSE102x SPI support")
CC: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pcs-lynx.c used lynx_pcs and lynx as a variable name within the same file.
This standardizes all internal variables to just "lynx"
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A simple variable update from "pcs" to "mdio_device" for the mdio device
will make things a little cleaner.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A simple variable update from "pcs" to "mdio_device" for the mdio device
will make things a little cleaner.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple rename of a variable to make things more logical.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove references to lynx_pcs structures so drivers like the Felix DSA
can reference alternate PCS drivers.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 26eee0210a ("net/fsl: fix a bug in xgmac_mdio") fixed a bug in
the QorIQ mdio driver but left the (now unused) incorrect bit definition
for MDIO_DATA_BSY in the code. This commit removes it.
Signed-off-by: Markus Koch <markus@notsyncing.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In [1], Christoph Hellwig has proposed to remove the wrappers in
include/linux/pci-dma-compat.h.
Some reasons why this API should be removed have been given by Julia
Lawall in [2].
A coccinelle script has been used to perform the needed transformation
Only relevant parts are given below.
@@
expression e1, e2;
@@
- pci_dma_mapping_error(e1, e2)
+ dma_mapping_error(&e1->dev, e2)
[1]: https://lore.kernel.org/kernel-janitors/20200421081257.GA131897@infradead.org/
[2]: https://lore.kernel.org/kernel-janitors/alpine.DEB.2.22.394.2007120902170.2424@hadrien/
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dma_set_mask_and_coherent() instead of unrolling it with some
dma_set_mask()+dma_set_coherent_mask().
Moreover, as stated in [1], dma_set_mask() with a 64-bit mask will never
fail if dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
Simplify code and remove some dead code accordingly.
Now that qed_set_coherency_mask() is mostly a single call to
dma_set_mask_and_coherent(), fold it in its only caller.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dma_set_mask_and_coherent() instead of unrolling it with some
dma_set_mask()+dma_set_coherent_mask().
Moreover, as stated in [1], dma_set_mask() with a 64-bit mask will never
fail if dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
That said, 'pci_using_dac' can only be 1 after a successful
dma_set_mask_and_coherent().
Simplify code and remove some dead code accordingly.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dma_set_mask_and_coherent() instead of unrolling it with some
dma_set_mask()+dma_set_coherent_mask().
Moreover, as stated in [1], dma_set_mask() with a 64-bit mask will never
fail if dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
That said, 'pci_using_dac' can only be 1 after a successful
dma_set_mask_and_coherent().
Simplify code and remove some dead code accordingly.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hytera makes a range of digital (DMR) radios. These radios can be
programmed to a allow a computer to control them over Ethernet over USB,
either using NCM or RNDIS.
This commit adds support for RNDIS for Hytera radios. I tested with a
Hytera PD785 and a Hytera MD785G. When these radios are programmed to
set up a Radio to PC Network using RNDIS, an USB interface will be added
with class 2 (Communications), subclass 2 (Abstract Modem Control) and
an interface protocol of 255 ("vendor specific" - lsusb even hints "MSFT
RNDIS?").
This patch is similar to the solution of this StackOverflow user, but
that only works for the Hytera MD785:
https://stackoverflow.com/a/53550858
To use the "Radio to PC Network" functionality of Hytera DMR radios, the
radios need to be programmed correctly in CPS (Hytera's Customer
Programming Software). "Forward to PC" should be checked in "Network"
(under "General Setting" in "Conventional") and the "USB Network
Communication Protocol" should be set to RNDIS.
Signed-off-by: Thomas Toye <thomas@toye.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
The role of ena_calc_max_io_queue_num() is to return the number
of queues supported by the device, which means the return value
should be >=0.
The function that calls ena_calc_max_io_queue_num(), checks
the return value. If it is 0, it means the device reported
it supports 0 IO queues. This case is considered an error
and is handled by the calling function accordingly.
However the current implementation of ena_calc_max_io_queue_num()
is wrong, since when it detects the device supports 0 IO queues,
it returns -EFAULT.
In such a case the calling function doesn't detect the error,
and therefore doesn't handle it.
This commit changes ena_calc_max_io_queue_num() to return 0
in case the device reported it supports 0 queues, allowing the
calling function to properly handle the error case.
Fixes: 736ce3f414 ("net: ena: make ethtool -l show correct max number of queues")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A wrong request id received from the device is a sign that
something is wrong with it, therefore trigger a device reset.
Also add some debug info to the "Page is NULL" print to make
it easier to debug.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ena_com_tx_comp_req_id_get() checks the req_id of a received completion,
and if it is out of bounds returns -EINVAL. This is a sign that
something is wrong with the device and it needs to be reset.
The current code does not reset the device in this case, which leaves
the driver in an undefined state, where this completion is not properly
handled.
This commit adds a call to handle_invalid_req_id() in ena_clean_tx_irq()
and ena_clean_xdp_irq() which resets the device to fix the issue.
This commit also removes unnecessary request id checks from
validate_tx_req_id() and validate_xdp_req_id(). This check is unneeded
because it was already performed in ena_com_tx_comp_req_id_get(), which
is called right before these functions.
Fixes: 548c4940b9 ("net: ena: Implement XDP_TX action")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dma_set_mask_and_coherent() instead of unrolling it with some
dma_set_mask()+dma_set_coherent_mask().
Moreover, as stated in [1], dma_set_mask_and_coherent() with a 64-bit mask
will never fail if dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
That said, 'pci_using_dac' can only be 1 after a successful
dma_set_mask_and_coherent().
Simplify code and remove some dead code accordingly.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dma_set_mask_and_coherent() instead of unrolling it with some
dma_set_mask()+dma_set_coherent_mask().
This simplifies code and removes some dead code (dma_set_coherent_mask()
can not fail after a successful dma_set_mask())
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-12-30
The following pull-request contains BPF updates for your *net-next* tree.
We've added 72 non-merge commits during the last 20 day(s) which contain
a total of 223 files changed, 3510 insertions(+), 1591 deletions(-).
The main changes are:
1) Automatic setrlimit in libbpf when bpf is memcg's in the kernel, from Andrii.
2) Beautify and de-verbose verifier logs, from Christy.
3) Composable verifier types, from Hao.
4) bpf_strncmp helper, from Hou.
5) bpf.h header dependency cleanup, from Jakub.
6) get_func_[arg|ret|arg_cnt] helpers, from Jiri.
7) Sleepable local storage, from KP.
8) Extend kfunc with PTR_TO_CTX, PTR_TO_MEM argument support, from Kumar.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5 Software steering, New features and optimizations
This patch series brings various SW steering features, optimizations and
debug-ability focused improvements.
1) Expose debugfs for dumping the SW steering resources
2) Removing unused fields
3) support for matching on new fields
4) steering optimization for RX/TX-only rules
5) Make Software steering the default steering mechanism when
available, applies only to Switchdev mode FDB
From Yevgeny Kliteynik and Muhammad Sammar:
- Patch 1 fixes an error flow in creating matchers
- Patch 2 fix lower case macro prefix "mlx5_" to "MLX5_"
- Patch 3 removes unused struct member in mlx5dr_matcher
- Patch 4 renames list field in matcher struct to list_node to reflect the
fact that is field is for list node that is stored on another struct's lists
- Patch 5 adds checking for valid Flex parser ID value
- Patch 6 adds the missing reserved fields to dr_match_param and aligns it to
the format that is defined by HW spec
- Patch 7 adds support for dumping SW steering (SMFS) resources using debugfs
in CSV format: domain and its tables, matchers and rules
- Patch 8 adds support for a new destination type - UPLINK
- Patch 9 adds WARN_ON_ONCE on refcount checks in SW steering object destructors
- Patches 10, 11, 12 add misc5 flow table match parameters and add support for
matching on tunnel headers 0 and 1
- Patch 13 adds support for matching on geneve_tlv_option_0_exist field
- Patch 14 implements performance optimization for for empty or RX/TX-only
matchers by splitting RX and TX matchers handling: matcher connection in the
matchers chain is split into two separate lists (RX only and TX only), which
solves a usecase of many RX or TX only rules that create a long chain of
RX/TX-only paths w/o the actual rules
- Patch 15 ignores modify TTL if device doesn't support it instead of
adding and unsupported action
- Patch 16 sets SMFS as a default steering mode
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmHOvKsACgkQSD+KveBX
+j4CpQf8Cc3NkWhGVYYhRBlntdpyVTDpoVhw6RDXVwboIRZ3GcMm81SxgwKrDuUx
Yhup4K1CNKt44D1RRhX4ElSemfo/afxfGIcq7S87vciUOaebWTIZgRyNvuYr/buI
v9LIM7zTb1aXL7m3KQHOGc7cucVRvsNjteTxvp/DR0bPFEuzAr5tw9Y5qop9pBbM
cfgdmXKUoRxA039mqZ2Fl7y+z51zRkfsCza7lEHcGgpvwOLubFEaghj7YTIT6h1m
+We8w3/+B0mqS0HpByIxmyf/EQBG5Hl7FTbFj1Somn7EFEP4E+LaFzg8nGsUHEeI
f5027uM7XGlThAUrgdaOMcwBfIuOww==
=BE8m
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2021-12-28' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 Software steering, New features and optimizations
This patch series brings various SW steering features, optimizations and
debug-ability focused improvements.
1) Expose debugfs for dumping the SW steering resources
2) Removing unused fields
3) support for matching on new fields
4) steering optimization for RX/TX-only rules
5) Make Software steering the default steering mechanism when
available, applies only to Switchdev mode FDB
From Yevgeny Kliteynik and Muhammad Sammar:
- Patch 1 fixes an error flow in creating matchers
- Patch 2 fix lower case macro prefix "mlx5_" to "MLX5_"
- Patch 3 removes unused struct member in mlx5dr_matcher
- Patch 4 renames list field in matcher struct to list_node to reflect the
fact that is field is for list node that is stored on another struct's lists
- Patch 5 adds checking for valid Flex parser ID value
- Patch 6 adds the missing reserved fields to dr_match_param and aligns it to
the format that is defined by HW spec
- Patch 7 adds support for dumping SW steering (SMFS) resources using debugfs
in CSV format: domain and its tables, matchers and rules
- Patch 8 adds support for a new destination type - UPLINK
- Patch 9 adds WARN_ON_ONCE on refcount checks in SW steering object destructors
- Patches 10, 11, 12 add misc5 flow table match parameters and add support for
matching on tunnel headers 0 and 1
- Patch 13 adds support for matching on geneve_tlv_option_0_exist field
- Patch 14 implements performance optimization for for empty or RX/TX-only
matchers by splitting RX and TX matchers handling: matcher connection in the
matchers chain is split into two separate lists (RX only and TX only), which
solves a usecase of many RX or TX only rules that create a long chain of
RX/TX-only paths w/o the actual rules
- Patch 15 ignores modify TTL if device doesn't support it instead of
adding and unsupported action
- Patch 16 sets SMFS as a default steering mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
currently most cmdq APIs are unified in hclge_comm_cmd.c. Newly developed
cmdq APIs should also be placed in hclge_comm_cmd.c. So there is no need to
keep hclge_cmd.c and hclgevf_cmd.c.
This patch moves the hclge(vf)_cmd_send to hclge(vf)_main.c and deletes
the source files and makefile scripts.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses common cmdq init and uninit APIs to replace the old APIs in
VF cmdq module init and uninit module. Then the old VF init and uninit
APIs is deleted.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses common cmdq init and uninit APIs to replace the old APIs in
PF cmdq module init and uninit modules. Then the old PF init and uninit
APIs is deleted.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PF and VF cmdq init and uninit APIs are also almost same espect the
suffixes of API names.
This patch creates common cmdq init and uninit APIs needed by PF and VF
cmdq modules. The next patch will use the new unified APIs to replace init
and uninit APIs in PF module.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses common cmdq resource allocate/free/query APIs to replace
the old APIs in VF cmdq module and deletes the old cmdq resource APIs.
Still we kept hclgevf_cmd_setup_basic_desc name as a seam API to avoid too
many meaningless replacement.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses common cmdq resource allocate/free/query APIs to replace
the old APIs in PF cmdq module and deletes the old cmdq resource APIs.
Still we kept hclge_cmd_setup_basic_desc name as a seam API to avoid too
many meaningless replacement.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PF and VF cmdq module resource allocate/free/query APIs are almost the
same espect the suffixes of API names. These same implementations bring
double development and bugfix work.
This patch creates common cmdq resource allocate/free/query APIs called by
PF and VF cmdq init/uninit APIs. The next patch will use the new unified
APIs to replace init/uninit APIs.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch firstly uses new hardware description struct hclge_comm_hw as
child member of hclgevf_hw and deletes the old hardware description child
members. All the hclgevf_hw variables used in VF module is modified
according to the new hclgevf_hw.
Secondly hclgevf_cmd_send is refactored to use hclge_comm_cmd_send APIs.
The old functions called by hclgevf_cmd_send are all deleted. Still we kept
hclgevf_cmd_send to avoid too many meaningless modifications.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch firstly uses new hardware description struct hclge_comm_hw as
child member of hclge_hw and deletes the original child memebers of
hclge_hw. All the hclge_hw variables used in PF module is modified
according to the new hclge_hw.
Secondly hclge_cmd_send is refactored to use hclge_comm_cmd_send APIs. The
old functions called by hclge_cmd_send are deleted and hclge_cmd_send is
kept to avoid too many meaningless modifications.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch create new set of unified hclge_comm_cmd_send APIs for PF and VF
cmdq module. Subfunctions called by hclge_comm_cmd_send are also created
include cmdq result check, cmdq return code conversion and ring space
opertaion APIs.
These new common cmdq APIs will be used to replace the old PF and VF cmdq
APIs in next patches.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch use new common struct hclge_desc to replace struct hclgevf_desc
in VF cmdq module and then delete the old struct hclgevf_desc.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently PF and VF cmdq APIs use struct hclge(vf)_hw to describe cmdq
hardware information needed by hclge(vf)_cmd_send. There are a little
differences between its child struct hclge_cmq_ring and hclgevf_cmq_ring.
It is redundent to use two sets of structures to support same functions.
So this patch creates new set of common cmdq hardware description
structures(hclge_comm_hw) to unify PF and VF cmdq functions. The struct
hclge_desc is still kept to avoid too many meaningless replacement.
These new structures will be used to unify hclge(vf)_hw structures in PF
and VF cmdq APIs in next patches.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we plan to refactor PF and VF cmdq module. A new file folder
hns3_common will be created to store new common APIs used by PF and VF
cmdq module. Thus the PF and VF compilation process will both depends on
the hns3_common. This may cause parallel building problems if we add a new
makefile building unit.
So this patch combined the PF and VF makefile scripts to the top level
makefile to support the new hns3_common which will be created in the next
patch.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set SMFS (SW-managed flow steering) as a default steering mode
instead of DMFS (device-managed flow steering)
In SMFS, the driver writes the STEs (Steering Table Entries) directly
to the device's ICM, which allows for a higher rule insertion rate
than through using FW command interface, as it is done in DMFS.
SMFS/DMFS steering modes can be configured through devlink param
'flow_steering_mode'. The possible values are 'smfs' or 'dmfs'.
The desired 'flow_steering_mode' param value should be set before
enabling switchdev mode.
Example:
# devlink dev param set pci/0000:05:00.0 name flow_steering_mode smfs
# devlink dev eswitch set pci/0000:05:00.0 mode switchdev
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
When modifying TTL, packet's csum has to be recalculated.
Due to HW issue in ConnectX-5, csum recalculation for modify TTL
is supported through a work-around that is specifically enabled
by configuration.
If the work-around isn't enabled, ignore the modify TTL action
rather than adding an unsupported action.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Every matcher has RX and TX paths. When a new matcher is created, its RX
and TX start/end anchors are connected to the respective RX and TX anchors
of the previous and next matchers.
This creates a potential performance issue: when a certain rule is added
to a matcher, in many cases it is RX or TX only rule, which may create a
long chain of RX/TX-only paths w/o the actual rules.
This patch aims to handle this issue.
RX and TX matchers are now handled separately: matcher connection in the
matchers chain is split into two separate lists: RX only and TX only.
when a new matcher is created, it is initially created 'detached' - its
RX/TX members are not inserted into the table's matcher list.
When an actual rule is added, only its appropriate RX or TX nic matchers
are then added to the table's nic matchers list and inserted into its
place in the chain of matchers.
I.e., if the rule that is being added is an RX-only rule, only the RX
part of the matcher will be connected to the chain, while TX part of the
matcher remains detached and doesn't prolong the TX chain of the matchers.
Same goes for rule deletion: when the last RX/TX rule of the nic matcher
is destroyed, the nic matcher is removed from its list.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Match on geneve_tlv_option_0_exist field on devices that support STEv1.
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Tunnel headers are generic encapsulation headers, applies for all
tunneling protocols identified by the device native parser or by the
programmable parser, this support will enable raw matching headers 0 and 1.
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Add support for misc5 match parameter as per HW spec, this will allow
matching on tunnel_header fields.
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Extend mlx5 debugfs support to present Software Steering resources:
dr_domain including it's tables, matchers and rules.
The interface is read-only. While dump is being presented, new steering
rules cannot be inserted/deleted.
The steering information is dumped in the CSV form with the following
format:
<object_type>,<object_ID>, <object_info>,...,<object_info>
This data can be read at the following path:
/sys/kernel/debug/mlx5/<BDF>/steering/fdb/<domain_handle>
Example:
# cat /sys/kernel/debug/mlx5/0000:82:00.0/steering/fdb/dmn_000018644
3100,0x55caa4621c50,0xee802,4,65533
3101,0x55caa4621c50,0xe0100008
Changes in V2:
- Reduce temp hex buffer size and avoid unnecessary memset
- Use bin2hex() instead of DIY loop
- Don't check debugfs functions return values
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Allow only legal values for flex parser ID - values from 0 to 7.
For other values skip the parser, and as a result the matcher creation
will fail for using invalid flex parser ID.
Signed-off-by: Hamdan Igbaria <hamdani@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
In dr_types structs, some list fields are list heads, and some
are just list nodes that are stored on the other structs' lists.
Rename the appropriate list field to reflect this distinction.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Macros prefix should be capital letters - fix the prefix in
mlx5_FLEX_PARSER_MPLS_OVER_UDP_ENABLED.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
The error code of nic matcher init functions wasn't checked.
This patch improves the matcher init function and fix error flow bug:
the handling of match parameter is moved into a separate function
and error flow is simplified.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
1. Define more regs. Some switches (e.g. BCM4908) have up to 6 regs.
2. Add helper for handling non-lineral port <-> reg mappings.
3. Add support for 12 B LED reg blocks on BCM4908 (different layout)
Complete support for LEDs setup will be implemented once Linux receives
a proper design & implementation for "hardware" LEDs.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211229171642.22942-1-zajec5@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c
commit 077cdda764 ("net/mlx5e: TC, Fix memory leak with rules with internal port")
commit 31108d142f ("net/mlx5: Fix some error handling paths in 'mlx5e_tc_add_fdb_flow()'")
commit 4390c6edc0 ("net/mlx5: Fix some error handling paths in 'mlx5e_tc_add_fdb_flow()'")
https://lore.kernel.org/all/20211229065352.30178-1-saeed@kernel.org/
net/smc/smc_wr.c
commit 49dc9013e3 ("net/smc: Use the bitmap API when applicable")
commit 349d43127d ("net/smc: fix kernel panic caused by race of smc_sock")
bitmap_zero()/memset() is removed by the fix
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The reference taken by 'of_find_device_by_node()' must be released when
not needed anymore.
Add the corresponding 'put_device()' in the and error handling paths.
Fixes: 18a6c85fcc ("fsl/fman: Add FMan Port Support")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by checkpatch.pl, no space is necessary after a cast.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch.pl complains as the following:
Alignment should match open parenthesis
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Documentation/process/coding-style.rst says (in line 88)
"Don't put multiple assignments on a single line either."
This patch fixes the coding style issue reported by checkpatch.pl.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add () around macro argument to avoid precedence issues
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
strlcpy is marked as deprecated in Documentation/process/deprecated.rst,
and there is no functional difference when the caller expects truncation
(when not checking the return value). strscpy is relatively better as it
also avoids scanning the whole source string.
This silences the related checkpatch warnings from:
commit 5dbdb2d87c ("checkpatch: prefer strscpy to strlcpy")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to enable flow-director filter when multiple TCs are
configured. Flow director filter can be configured using ethtool
(--config-ntuple option). When multiple TCs are configured, each
TC is mapped to an unique HW VSI. So VSI corresponding to queue
used in filter is identified and flow director context is updated
with correct VSI while configuring ntuple filter in HW.
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
queue
Tony Nguyen says:
====================
1GbE Intel Wired LAN Driver Updates 2021-12-29
Ruud Bos says:
The igb driver provides support for PEROUT and EXTTS pin functions that
allow adapter external use of timing signals. At Hottinger Bruel & Kjaer we
are using the PEROUT function to feed a PTP corrected 1pps signal into an
FPGA as cross system synchronized time source.
Support for the PEROUT and EXTTS SDP functions is currently limited to
i210/i211 based adapters. This patch series enables these functions also
for 82580/i354/i350 based ones. Because the time registers of these
adapters do not have the nice split in second rollovers as the i210 has,
the implementation is slightly more complex compared to the i210
implementation.
The PEROUT function has been successfully tested on an i350 based ethernet
adapter. Using the following user space code excerpt, the driver outputs a
PTP corrected 1pps signal on the SDP0 pin of an i350:
struct ptp_pin_desc desc;
memset(&desc, 0, sizeof(desc));
desc.index = 0;
desc.func = PTP_PF_PEROUT;
desc.chan = 0;
if (ioctl(fd, PTP_PIN_SETFUNC, &desc) == 0) {
struct timespec ts;
if (clock_gettime(clkid, &ts) == 0) {
struct ptp_perout_request rq;
memset(&rq, 0, sizeof(rq));
rq.index = 0;
rq.start.sec = ts.tv_sec + 1;
rq.start.nsec = 500000000;
rq.period.sec = 1;
rq.period.nsec = 0;
if (ioctl(fd, PTP_PEROUT_REQUEST, &rq) == 0) {
/* 1pps signal is now available on SDP0 */
}
}
}
The added EXTTS function has not been tested. However, looking at the data
sheets, the layout of the registers involved match the i210 exactly except
for the time registers mentioned before. Hence the almost identical
implementation.
---
Note: I made changes to fix RCT and checkpatch messages regarding
unnecessary parenthesis.
====================
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add inetaddr notifiers to support add/del IPv4 address on switchdev
port. We create TRAP on first address, added on port and delete TRAP,
when last address removed.
Currently, driver supports only regular port to became routed.
Other port type support will be added later
Co-developed-by: Taras Chornyi <tchornyi@marvell.com>
Signed-off-by: Taras Chornyi <tchornyi@marvell.com>
Co-developed-by: Oleksandr Mazur <oleksandr.mazur@plvision.eu>
Signed-off-by: Oleksandr Mazur <oleksandr.mazur@plvision.eu>
Signed-off-by: Yevhen Orlov <yevhen.orlov@plvision.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initial implementation of notification handlers. For now this is just
stub.
So that we can move forward and add prestera_router_hw's objects
manipulations.
We support several addresses on interface. We just have nothing to do for
second address, because rif is already enabled on this interface, after
first one.
Co-developed-by: Taras Chornyi <tchornyi@marvell.com>
Signed-off-by: Taras Chornyi <tchornyi@marvell.com>
Co-developed-by: Oleksandr Mazur <oleksandr.mazur@plvision.eu>
Signed-off-by: Oleksandr Mazur <oleksandr.mazur@plvision.eu>
Signed-off-by: Yevhen Orlov <yevhen.orlov@plvision.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add prestera_router_hw.c. This file contains functions, which track HW
objects relations and links. This include implicity creation of objects,
that needed by requested one and implicity removing of objects, which
reference counter is became zero.
We need this layer, because kernel callbacks not always mapped to
creation of single HW object. So let it be two different layers - one
for subscribing and parsing kernel structures, and another
(prestera_router_hw.c) for HW objects relations tracking.
There is two types of objects on router_hw layer:
- Explicit objects (rif_entry) : created by higher layer.
- Implicit objects (vr) : created on demand by explicit objects.
Co-developed-by: Taras Chornyi <tchornyi@marvell.com>
Signed-off-by: Taras Chornyi <tchornyi@marvell.com>
Co-developed-by: Oleksandr Mazur <oleksandr.mazur@plvision.eu>
Signed-off-by: Oleksandr Mazur <oleksandr.mazur@plvision.eu>
Signed-off-by: Yevhen Orlov <yevhen.orlov@plvision.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add prestera_router.c, which contains code to subscribe/unsubscribe on
kernel notifiers for router. This handle kernel notifications,
parse structures to make key to manipulate prestera_router_hw's objects.
Also prestera_router is container for router's objects database.
Co-developed-by: Taras Chornyi <tchornyi@marvell.com>
Signed-off-by: Taras Chornyi <tchornyi@marvell.com>
Co-developed-by: Oleksandr Mazur <oleksandr.mazur@plvision.eu>
Signed-off-by: Oleksandr Mazur <oleksandr.mazur@plvision.eu>
Signed-off-by: Yevhen Orlov <yevhen.orlov@plvision.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions to enable routing on port, which is not in vlan.
Also we can enable routing on vlan.
prestera_hw_rif_create() take index of allocated virtual router.
Co-developed-by: Taras Chornyi <tchornyi@marvell.com>
Signed-off-by: Taras Chornyi <tchornyi@marvell.com>
Co-developed-by: Oleksandr Mazur <oleksandr.mazur@plvision.eu>
Signed-off-by: Oleksandr Mazur <oleksandr.mazur@plvision.eu>
Signed-off-by: Yevhen Orlov <yevhen.orlov@plvision.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions and structures to allocate virtual router.
prestera_hw_vr_create() return index of allocated VR so that we can move
forward and also add another objects (e.g. router interface),
which has link to VR.
Co-developed-by: Taras Chornyi <tchornyi@marvell.com>
Signed-off-by: Taras Chornyi <tchornyi@marvell.com>
Co-developed-by: Oleksandr Mazur <oleksandr.mazur@plvision.eu>
Signed-off-by: Oleksandr Mazur <oleksandr.mazur@plvision.eu>
Signed-off-by: Yevhen Orlov <yevhen.orlov@plvision.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing includes unmasked by the subsequent change.
Mostly network drivers missing an include for XDP_PACKET_HEADROOM.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20211230012742.770642-2-kuba@kernel.org
Thanks for your review. Here is the new version for this patch.
This patch adds support for the emac rx dma present on sun4i. The emac
is able to move packets from rx fifo to RAM by using dma.
Change since v4.
- rename sbk field to skb
- rename alloc_emac_dma_req to emac_alloc_dma_req
- using kzalloc(..., GPF_ATOMIC) in interrupt context to avoid
sleeping
- retry by using emac_inblk_32bit when emac_dma_inblk_32bit fails
- fix some code style issues
Change since v5.
- fix some code style issue
Signed-off-by: Conley Lee <conleylee@foxmail.com>
Link: https://lore.kernel.org/r/tencent_DE05ADA53D5B084D4605BE6CB11E49EF7408@qq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the userspace program is distributed in binary form (distro package),
there is no way to know on which kernel versions it will run.
Let's only check if the flag was set when do SIOCSHWTSTAMP. And return
hwtstamp_config with flag HWTSTAMP_FLAG_BONDED_PHC_INDEX to notify
userspace whether the new feature is supported or not.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Fixes: 085d610008 ("Bonding: force user to add HWTSTAMP_FLAG_BONDED_PHC_INDEX when get/set HWTSTAMP")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Support for the PTP pin function on 82580/i354/i350 based adapters.
Because the time registers of these adapters do not have the nice split in
second rollovers as the i210 has, the implementation is slightly more
complex compared to the i210 implementation.
Signed-off-by: Ruud Bos <kernel.hbk@gmail.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Support for the PEROUT PTP pin function on 82580/i354/i350 based adapters.
Because the time registers of these adapters do not have the nice split in
second rollovers as the i210 has, the implementation is slightly more
complex compared to the i210 implementation.
Signed-off-by: Ruud Bos <kernel.hbk@gmail.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove code duplication in the tsync interrupt handler function by moving
this logic to separate functions. This keeps the interrupt handler readable
and allows the new functions to be extended for adapter types other than
i210.
Signed-off-by: Ruud Bos <kernel.hbk@gmail.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Allow reuse of SDP config struct initialization by moving it to a
separate function.
Signed-off-by: Ruud Bos <kernel.hbk@gmail.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
sock.h is pretty heavily used (5k objects rebuilt on x86 after
it's touched). We can drop the include of filter.h from it and
add a forward declaration of struct sk_filter instead.
This decreases the number of rebuilt objects when bpf.h
is touched from ~5k to ~1k.
There's a lot of missing includes this was masking. Primarily
in networking tho, this time.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/bpf/20211229004913.513372-1-kuba@kernel.org
In case of an error in mlx5e_set_features(), 'netdev->features' must be
updated with the correct state of the device to indicate which features
were updated successfully.
To do that we maintain a copy of 'netdev->features' and update it after
successful feature changes, so we can assign it to back to
'netdev->features' if needed.
However, since not all netdev features are handled by the driver (e.g.
GRO/TSO/etc), some features may not be updated correctly in case of an
error updating another feature.
For example, while requesting to disable TSO (feature which is not
handled by the driver) and enable HW-GRO, if an error occurs during
HW-GRO enable, 'oper_features' will be assigned with 'netdev->features'
and HW-GRO turned off. TSO will remain enabled in such case, which is a
bug.
To solve that, instead of using 'netdev->features' as the baseline of
'oper_features' and changing it on set feature success, use 'features'
instead and update it in case of errors.
Fixes: 75b81ce719 ("net/mlx5e: Don't override netdev features field unless in error flow")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Fix a memory leak with decap rule with internal port as destination
device. The driver allocates a modify hdr action but doesn't set
the flow attr modify hdr action which results in skipping releasing
the modify hdr action when releasing the flow.
backtrace:
[<000000005f8c651c>] krealloc+0x83/0xd0
[<000000009f59b143>] alloc_mod_hdr_actions+0x156/0x310 [mlx5_core]
[<000000002257f342>] mlx5e_tc_match_to_reg_set_and_get_id+0x12a/0x360 [mlx5_core]
[<00000000b44ea75a>] mlx5e_tc_add_fdb_flow+0x962/0x1470 [mlx5_core]
[<0000000003e384a0>] __mlx5e_add_fdb_flow+0x54c/0xb90 [mlx5_core]
[<00000000ed8b22b6>] mlx5e_configure_flower+0xe45/0x4af0 [mlx5_core]
[<00000000024f4ab5>] mlx5e_rep_indr_offload.isra.0+0xfe/0x1b0 [mlx5_core]
[<000000006c3bb494>] mlx5e_rep_indr_setup_tc_cb+0x90/0x130 [mlx5_core]
[<00000000d3dac2ea>] tc_setup_cb_add+0x1d2/0x420
Fixes: b16eb3c81f ("net/mlx5: Support internal port as decap route device")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-12-28
This series contains updates to igc driver only.
Vinicius disables support for crosstimestamp on i225-V as lockups are being
observed.
James McLaughlin fixes Tx timestamping support on non-MSI-X platforms.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
igc: Fix TX timestamp support for non-MSI-X platforms
igc: Do not enable crosstimestamping for i225-V models
====================
Link: https://lore.kernel.org/r/20211228182421.340354-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
10GbE Intel Wired LAN Driver Updates 2021-12-28
Alexander Lobakin says:
napi_build_skb() I introduced earlier this year ([0]) aims
to decrease MM pressure and the overhead from in-place
kmem_cache_alloc() on each Rx entry processing by decaching
skbuff_heads from NAPI per-cpu cache filled prior to that by
napi_consume_skb() (so it is sort of a direct shortcut for
free -> mm -> alloc cycle).
Currently, no in-tree drivers use it. Switch all Intel Ethernet
drivers to it to get slight-to-medium perf boosts depending on
the frame size.
ice driver, 50 Gbps link, pktgen + XDP_PASS (local in) sample:
frame_size/nthreads 64/42 128/20 256/8 512/4 1024/2 1532/1
net-next (Kpps) 46062 34654 18248 9830 5343 2714
series 47438 34708 18330 9875 5435 2777
increase 2.9% 0.15% 0.45% 0.46% 1.72% 2.32%
Additionally, e1000's been switched to napi_consume_skb() as it's
safe and works fine there, and there's no point in napi_build_skb()
without paired NAPI cache feeding point.
[0] https://lore.kernel.org/all/20210213141021.87840-1-alobakin@pm.me
* '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ixgbevf: switch to napi_build_skb()
ixgbe: switch to napi_build_skb()
igc: switch to napi_build_skb()
igb: switch to napi_build_skb()
ice: switch to napi_build_skb()
iavf: switch to napi_build_skb()
i40e: switch to napi_build_skb()
e1000: switch to napi_build_skb()
e1000: switch to napi_consume_skb()
====================
Link: https://lore.kernel.org/r/20211228175815.281449-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When allocated, this bitmap is not initialized. Only the first bit is set a
few lines below.
Use bitmap_zalloc() to make sure that it is cleared before being used.
Fixes: 6461b446f2 ("ionic: Add interrupts and doorbells")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Link: https://lore.kernel.org/r/6a478eae0b5e6c63774e1f0ddb1a3f8c38fa8ade.1640527506.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds a missing line after the declaration and
fixes the checkpatch warning:
WARNING: Missing a blank line after declarations
+ int desc;
+ for (desc = 0; desc < LTQ_DESC_NUM; desc++)
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://lore.kernel.org/r/20211228220031.71576-1-olek2@wp.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds the missing code comment for memory barrier
call and fixes checkpatch warning:
WARNING: memory barrier without comment
+ wmb();
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://lore.kernel.org/r/20211228214910.70810-1-olek2@wp.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since referenced change pci_irq_vector() can't be used in atomic
context any longer. This conflicts with our usage of this function
in rtl8169_netpoll(). Therefore store the interrupt number in
struct rtl8169_private.
Fixes: 495c66aca3 ("genirq/msi: Convert to new functions")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/3cd24763-f307-78f5-76ed-a5fbf315fb28@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Time synchronization was not properly enabled on non-MSI-X platforms.
Fixes: 2c344ae245 ("igc: Add support for TX timestamping")
Signed-off-by: James McLaughlin <james.mclaughlin@qsc.com>
Reviewed-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
It was reported that when PCIe PTM is enabled, some lockups could
be observed with some integrated i225-V models.
While the issue is investigated, we can disable crosstimestamp for
those models and see no loss of functionality, because those models
don't have any support for time synchronization.
Fixes: a90ec84837 ("igc: Add support for PTP getcrosststamp()")
Link: https://lore.kernel.org/all/924175a188159f4e03bd69908a91e606b574139b.camel@gmx.de/
Reported-by: Stefan Dietrich <roots@gmx.de>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
napi_build_skb() reuses per-cpu NAPI skbuff_head cache in order
to save some cycles on freeing/allocating skbuff_heads on every
new Rx or completed Tx.
ixgbevf driver runs Tx completion polling cycle right before the Rx
one and uses napi_consume_skb() to feed the cache with skbuff_heads
of completed entries, so it's never empty and always warm at that
moment. Switch to the napi_build_skb() to relax mm pressure on
heavy Rx.
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
napi_build_skb() reuses per-cpu NAPI skbuff_head cache in order
to save some cycles on freeing/allocating skbuff_heads on every
new Rx or completed Tx.
ixgbe driver runs Tx completion polling cycle right before the Rx
one and uses napi_consume_skb() to feed the cache with skbuff_heads
of completed entries, so it's never empty and always warm at that
moment. Switch to the napi_build_skb() to relax mm pressure on
heavy Rx.
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
napi_build_skb() reuses per-cpu NAPI skbuff_head cache in order
to save some cycles on freeing/allocating skbuff_heads on every
new Rx or completed Tx.
igc driver runs Tx completion polling cycle right before the Rx
one and uses napi_consume_skb() to feed the cache with skbuff_heads
of completed entries, so it's never empty and always warm at that
moment. Switch to the napi_build_skb() to relax mm pressure on
heavy Rx.
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
napi_build_skb() reuses per-cpu NAPI skbuff_head cache in order
to save some cycles on freeing/allocating skbuff_heads on every
new Rx or completed Tx.
igb driver runs Tx completion polling cycle right before the Rx
one and uses napi_consume_skb() to feed the cache with skbuff_heads
of completed entries, so it's never empty and always warm at that
moment. Switch to the napi_build_skb() to relax mm pressure on
heavy Rx.
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
napi_build_skb() reuses per-cpu NAPI skbuff_head cache in order
to save some cycles on freeing/allocating skbuff_heads on every
new Rx or completed Tx.
ice driver runs Tx completion polling cycle right before the Rx
one and uses napi_consume_skb() to feed the cache with skbuff_heads
of completed entries, so it's never empty and always warm at that
moment. Switch to the napi_build_skb() to relax mm pressure on
heavy Rx.
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
napi_build_skb() reuses per-cpu NAPI skbuff_head cache in order
to save some cycles on freeing/allocating skbuff_heads on every
new Rx or completed Tx.
iavf driver runs Tx completion polling cycle right before the Rx
one and uses napi_consume_skb() to feed the cache with skbuff_heads
of completed entries, so it's never empty and always warm at that
moment. Switch to the napi_build_skb() to relax mm pressure on
heavy Rx.
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
napi_build_skb() reuses per-cpu NAPI skbuff_head cache in order
to save some cycles on freeing/allocating skbuff_heads on every
new Rx or completed Tx.
i40e driver runs Tx completion polling cycle right before the Rx
one and uses napi_consume_skb() to feed the cache with skbuff_heads
of completed entries, so it's never empty and always warm at that
moment. Switch to the napi_build_skb() to relax mm pressure on
heavy Rx.
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
napi_build_skb() reuses per-cpu NAPI skbuff_head cache in order
to save some cycles on freeing/allocating skbuff_heads on every
new Rx or completed Tx element.
e1000 driver runs Tx completion polling cycle right before the Rx
one. Now that e1000 uses napi_consume_skb() to put skbuff_heads of
completed entries into the cache, it will never empty and always
warm at that moment. Switch to the napi_build_skb() to relax mm
pressure on heavy Rx and increase throughput.
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In order to take the best from per-cpu NAPI skbuff_head caches and
CPU cycles, let's switch from dev_kfree_skb_any(), which passes skb
back to the mm layer, to napi_consume_skb(), which feeds those
caches on non-zero budget instead (falls back to the former on 0).
Do the replacement in e1000_unmap_and_free_tx_resource(). There are
4 call sites of this function throughout the driver:
* e1000_clean_tx_ring(). Slowpath, process context, cleans the
whole Tx ring on ifdown. Use budget of 0 here;
* e1000_tx_map(). Hotpath, net Tx softirq, unmaps the buffers in
case of error. Use 0 as well;
* e1000_clean_tx_irq(). Hotpath, NAPI Tx completion polling cycle.
As the driver doesn't count completed Tx entries towards the NAPI
budget, just use the poll budget of 64 to utilize caches.
Apart from being a preparation for switching to napi_build_skb(),
this is useful on its own as well, as napi_consume_skb() flushes
skb caches by batches of 32 instead of one-at-a-time.
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Received frames have FCS truncated. There is no need
to subtract FCS length from the statistics.
Fixes: fe1a56420c ("net: lantiq: Add Lantiq / Intel VRX200 Ethernet driver")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
'ndev' is a managed resource allocated with devm_alloc_etherdev(), so there
is no need to call free_netdev() explicitly or there will be a double
free().
Simplify all error handling paths accordingly.
Fixes: d51b6ce441 ("net: ethernet: add ag71xx driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delete the initialization of three static variables
because it is meaningless.
Signed-off-by: Wen Zhiwei <wenzhiwei@kylinos.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The D-Link DSB-650TX (2001:4002) is unable to receive Ethernet frames
that are longer than 1518 octets, for example, Ethernet frames that
contain 802.1Q VLAN tags.
The frames are sent to the pegasus driver via USB but the driver
discards them because they have the Long_pkt field set to 1 in the
received status report. The function read_bulk_callback of the pegasus
driver treats such received "packets" (in the terminology of the
hardware) as errors but the field simply does just indicate that the
Ethernet frame (MAC destination to FCS) is longer than 1518 octets.
It seems that in the 1990s there was a distinction between
"giant" (> 1518) and "runt" (< 64) frames and the hardware includes
flags to indicate this distinction. It seems that the purpose of the
distinction "giant" frames was to not allow infinitely long frames due
to transmission errors and to allow hardware to have an upper limit of
the frame size. However, the hardware already has such limit with its
2048 octet receive buffer and, therefore, Long_pkt is merely a
convention and should not be treated as a receive error.
Actually, the hardware is even able to receive Ethernet frames with 2048
octets which exceeds the claimed limit frame size limit of the driver of
1536 octets (PEGASUS_MTU).
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Matthias-Christian Ott <ott@mirix.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq() for DT users only.
While at it propagate error code in case request_irq() fails instead of
returning -EBUSY.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moshe Shemesh