Add support for OX810SE dwmac glue setup, which is a simplified version
of the OX820 introduced later with more control on the PHY interface.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In Linux bonding scenario, one packet is copied to several copies and sent
by all slave device of bond0 in mode 3(broadcast mode). The mode 3 xmit
function bond_xmit_broadcast() only ueses the last slave device's tx result
as the final result. In this case, if the last slave device is down, then
it always return NET_XMIT_DROP, even though the other slave devices xmit
success. It may cause the tx statistics error, and cause the application
(e.g. scp) consider the network is unreachable.
For example, use the following command to configure server A.
echo 3 > /sys/class/net/bond0/bonding/mode
ifconfig bond0 up
ifenslave bond0 eth0 eth1
ifconfig bond0 192.168.1.125
ifconfig eth0 up
ifconfig eth1 down
The slave device eth0 and eth1 are connected to server B(192.168.1.107).
Run the ping 192.168.1.107 -c 3 -i 0.2 command, the following information
is displayed.
PING 192.168.1.107 (192.168.1.107) 56(84) bytes of data.
64 bytes from 192.168.1.107: icmp_seq=1 ttl=64 time=0.077 ms
64 bytes from 192.168.1.107: icmp_seq=2 ttl=64 time=0.056 ms
64 bytes from 192.168.1.107: icmp_seq=3 ttl=64 time=0.051 ms
192.168.1.107 ping statistics
0 packets transmitted, 3 received
Actually, the slave device eth0 of the bond successfully sends three
ICMP packets, but the result shows that 0 packets are transmitted.
Also if we use scp command to get remote files, the command end with the
following printings.
ssh_exchange_identification: read: Connection timed out
So this patch modifies the bond_xmit_broadcast to return NET_XMIT_SUCCESS
if one slave device in the bond sends packets successfully. If all slave
devices send packets fail, the discarded packets stats is increased. The
skb is released when there is no slave device in the bond or the last slave
device is down.
Fixes: ae46f184bc ("bonding: propagate transmit status")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have seen cases where an endpoint RX completion interrupt arrives
while replenishing for the endpoint is underway. This causes another
instance of replenishing to begin as part of completing the receive
transaction. If this occurs it can lead to transaction corruption.
Use a new flag to ensure only one replenish instance for an endpoint
executes at a time.
Fixes: 84f9bd12d4 ("soc: qcom: ipa: IPA endpoints")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define a new replenish_flags bitmap to contain Boolean flags
associated with an endpoint's replenishing state. Replace the
replenish_enabled field with a flag in that bitmap. This is to
prepare for the next patch, which adds another flag.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ipa_endpoint_replenish(), if an error occurs when attempting to
replenish a receive buffer, we just quit and try again later. In
that case we increment the backlog count to reflect that the attempt
was unsuccessful. Then, if the add_one flag was true we increment
the backlog again.
This second increment is not included in the backlog local variable
though, and its value determines whether delayed work should be
scheduled. This is a bug.
Fix this by determining whether 1 or 2 should be added to the
backlog before adding it in a atomic_add_return() call.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Fixes: 84f9bd12d4 ("soc: qcom: ipa: IPA endpoints")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't populate the read-only const array offsets on the stack
but instead make it static. Also makes the object code a little smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220109231716.59012-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Mask the ECN bits before calling mlx5e_route_lookup_ipv4_get(). The
tunnel key might have the last ECN bit set. This interferes with the
route lookup process as ip_route_output_key_hash() interpretes this bit
specially (to restrict the route scope).
Found by code inspection, compile tested only.
Fixes: c7b9038d8a ("net/mlx5e: TC preparation refactoring for routing update event")
Fixes: 9a941117fb ("net/mlx5e: Maximize ip tunnel key usage on the TC offloading path")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Mask the ECN bits before calling ip_route_output_ports(). The tos
variable might be passed directly from an IPv4 header, so it may have
the last ECN bit set. This interferes with the route lookup process as
ip_route_output_key_hash() interpretes this bit specially (to restrict
the route scope).
Found by code inspection, compile tested only.
Fixes: 804c2f3e36 ("libcxgb,iw_cxgb4,cxgbit: add cxgb_find_route()")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch remove magic numbers in sun4i-emac.c and replace with macros
defined in sun4i-emac.h
Signed-off-by: Conley Lee <conleylee@foxmail.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Link: https://lore.kernel.org/r/tencent_71466C2135CD1780B19D7844BE3F167C940A@qq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit 6bf950a8ff.
To align with other vendors, NET_VENDOR configs are supposed to be ON by
default, while their drivers should default to OFF.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20220110205246.66298-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- Add new P-state driver for AMD processors (Huang Rui).
- Fix initialization of min and max frequency QoS requests in the
cpufreq core (Rafael Wysocki).
- Fix EPP handling on Alder Lake in intel_pstate (Srinivas Pandruvada).
- Make intel_pstate update cpuinfo.max_freq when notified of HWP
capabilities changes and drop a redundant function call from that
driver (Rafael Wysocki).
- Improve IRQ support in the Qcom cpufreq driver (Ard Biesheuvel,
Stephen Boyd, Vladimir Zapolskiy).
- Fix double devm_remap() in the Mediatek cpufreq driver (Hector Yuan).
- Introduce thermal pressure helpers for cpufreq CPU cooling (Lukasz
Luba).
- Make cpufreq use default_groups in kobj_type (Greg Kroah-Hartman).
- Make cpuidle use default_groups in kobj_type (Greg Kroah-Hartman).
- Fix two comments in cpuidle code (Jason Wang, Yang Li).
- Allow model-specific normal EPB value to be used in the intel_epb
sysfs attribute handling code (Srinivas Pandruvada).
- Simplify locking in pm_runtime_put_suppliers() (Rafael Wysocki).
- Add safety net to supplier device release in the runtime PM core
code (Rafael Wysocki).
- Capture device status before disabling runtime PM for it (Rafael
Wysocki).
- Add new macros for declaring PM operations to allow drivers to
avoid guarding them with CONFIG_PM #ifdefs or __maybe_unused and
update some drivers to use these macros (Paul Cercueil).
- Allow ACPI hardware signature to be honoured during restore from
hibernation (David Woodhouse).
- Update outdated operating performance points (OPP) documentation
(Tang Yizhou).
- Reduce log severity for informative message regarding frequency
transition failures in devfreq (Tzung-Bi Shih).
- Add DRAM frequency controller devfreq driver for Allwinner sunXi
SoCs (Samuel Holland).
- Add missing COMMON_CLK dependency to sun8i devfreq driver (Arnd
Bergmann).
- Add support for new layout of Psys PowerLimit Register on SPR to
the Intel RAPL power capping driver (Zhang Rui).
- Fix typo in a comment in idle_inject.c (Jason Wang).
- Remove unused function definition from the DTPM (Dynamit Thermal
Power Management) power capping framework (Daniel Lezcano).
- Reduce DTPM trace verbosity (Daniel Lezcano).
-----BEGIN PGP SIGNATURE-----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=1egI
-----END PGP SIGNATURE-----
Merge tag 'pm-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"The most signigicant change here is the addition of a new cpufreq
'P-state' driver for AMD processors as a better replacement for the
venerable acpi-cpufreq driver.
There are also other cpufreq updates (in the core, intel_pstate, ARM
drivers), PM core updates (mostly related to adding new macros for
declaring PM operations which should make the lives of driver
developers somewhat easier), and a bunch of assorted fixes and
cleanups.
Summary:
- Add new P-state driver for AMD processors (Huang Rui).
- Fix initialization of min and max frequency QoS requests in the
cpufreq core (Rafael Wysocki).
- Fix EPP handling on Alder Lake in intel_pstate (Srinivas
Pandruvada).
- Make intel_pstate update cpuinfo.max_freq when notified of HWP
capabilities changes and drop a redundant function call from that
driver (Rafael Wysocki).
- Improve IRQ support in the Qcom cpufreq driver (Ard Biesheuvel,
Stephen Boyd, Vladimir Zapolskiy).
- Fix double devm_remap() in the Mediatek cpufreq driver (Hector
Yuan).
- Introduce thermal pressure helpers for cpufreq CPU cooling (Lukasz
Luba).
- Make cpufreq use default_groups in kobj_type (Greg Kroah-Hartman).
- Make cpuidle use default_groups in kobj_type (Greg Kroah-Hartman).
- Fix two comments in cpuidle code (Jason Wang, Yang Li).
- Allow model-specific normal EPB value to be used in the intel_epb
sysfs attribute handling code (Srinivas Pandruvada).
- Simplify locking in pm_runtime_put_suppliers() (Rafael Wysocki).
- Add safety net to supplier device release in the runtime PM core
code (Rafael Wysocki).
- Capture device status before disabling runtime PM for it (Rafael
Wysocki).
- Add new macros for declaring PM operations to allow drivers to
avoid guarding them with CONFIG_PM #ifdefs or __maybe_unused and
update some drivers to use these macros (Paul Cercueil).
- Allow ACPI hardware signature to be honoured during restore from
hibernation (David Woodhouse).
- Update outdated operating performance points (OPP) documentation
(Tang Yizhou).
- Reduce log severity for informative message regarding frequency
transition failures in devfreq (Tzung-Bi Shih).
- Add DRAM frequency controller devfreq driver for Allwinner sunXi
SoCs (Samuel Holland).
- Add missing COMMON_CLK dependency to sun8i devfreq driver (Arnd
Bergmann).
- Add support for new layout of Psys PowerLimit Register on SPR to
the Intel RAPL power capping driver (Zhang Rui).
- Fix typo in a comment in idle_inject.c (Jason Wang).
- Remove unused function definition from the DTPM (Dynamit Thermal
Power Management) power capping framework (Daniel Lezcano).
- Reduce DTPM trace verbosity (Daniel Lezcano)"
* tag 'pm-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (53 commits)
x86, sched: Fix undefined reference to init_freq_invariance_cppc() build error
cpufreq: amd-pstate: Fix Kconfig dependencies for AMD P-State
cpufreq: amd-pstate: Fix struct amd_cpudata kernel-doc comment
cpuidle: use default_groups in kobj_type
x86: intel_epb: Allow model specific normal EPB value
MAINTAINERS: Add AMD P-State driver maintainer entry
Documentation: amd-pstate: Add AMD P-State driver introduction
cpufreq: amd-pstate: Add AMD P-State performance attributes
cpufreq: amd-pstate: Add AMD P-State frequencies attributes
cpufreq: amd-pstate: Add boost mode support for AMD P-State
cpufreq: amd-pstate: Add trace for AMD P-State module
cpufreq: amd-pstate: Introduce the support for the processors with shared memory solution
cpufreq: amd-pstate: Add fast switch function for AMD P-State
cpufreq: amd-pstate: Introduce a new AMD P-State driver to support future processors
ACPI: CPPC: Add CPPC enable register function
ACPI: CPPC: Check present CPUs for determining _CPC is valid
ACPI: CPPC: Implement support for SystemIO registers
x86/msr: Add AMD CPPC MSR definitions
x86/cpufeatures: Add AMD Collaborative Processor Performance Control feature flag
cpufreq: use default_groups in kobj_type
...
Core
----
- Defer freeing TCP skbs to the BH handler, whenever possible,
or at least perform the freeing outside of the socket lock section
to decrease cross-CPU allocator work and improve latency.
- Add netdevice refcount tracking to locate sources of netdevice
and net namespace refcount leaks.
- Make Tx watchdog less intrusive - avoid pausing Tx and restarting
all queues from a single CPU removing latency spikes.
- Various small optimizations throughout the stack from Eric Dumazet.
- Make netdev->dev_addr[] constant, force modifications to go via
appropriate helpers to allow us to keep addresses in ordered data
structures.
- Replace unix_table_lock with per-hash locks, improving performance
of bind() calls.
- Extend skb drop tracepoint with a drop reason.
- Allow SO_MARK and SO_PRIORITY setsockopt under CAP_NET_RAW.
BPF
---
- New helpers:
- bpf_find_vma(), find and inspect VMAs for profiling use cases
- bpf_loop(), runtime-bounded loop helper trading some execution
time for much faster (if at all converging) verification
- bpf_strncmp(), improve performance, avoid compiler flakiness
- bpf_get_func_arg(), bpf_get_func_ret(), bpf_get_func_arg_cnt()
for tracing programs, all inlined by the verifier
- Support BPF relocations (CO-RE) in the kernel loader.
- Further the support for BTF_TYPE_TAG annotations.
- Allow access to local storage in sleepable helpers.
- Convert verifier argument types to a composable form with different
attributes which can be shared across types (ro, maybe-null).
- Prepare libbpf for upcoming v1.0 release by cleaning up APIs,
creating new, extensible ones where missing and deprecating those
to be removed.
Protocols
---------
- WiFi (mac80211/cfg80211):
- notify user space about long "come back in N" AP responses,
allow it to react to such temporary rejections
- allow non-standard VHT MCS 10/11 rates
- use coarse time in airtime fairness code to save CPU cycles
- Bluetooth:
- rework of HCI command execution serialization to use a common
queue and work struct, and improve handling errors reported
in the middle of a batch of commands
- rework HCI event handling to use skb_pull_data, avoiding packet
parsing pitfalls
- support AOSP Bluetooth Quality Report
- SMC:
- support net namespaces, following the RDMA model
- improve connection establishment latency by pre-clearing buffers
- introduce TCP ULP for automatic redirection to SMC
- Multi-Path TCP:
- support ioctls: SIOCINQ, OUTQ, and OUTQNSD
- support socket options: IP_TOS, IP_FREEBIND, IP_TRANSPARENT,
IPV6_FREEBIND, and IPV6_TRANSPARENT, TCP_CORK and TCP_NODELAY
- support cmsgs: TCP_INQ
- improvements in the data scheduler (assigning data to subflows)
- support fastclose option (quick shutdown of the full MPTCP
connection, similar to TCP RST in regular TCP)
- MCTP (Management Component Transport) over serial, as defined by
DMTF spec DSP0253 - "MCTP Serial Transport Binding".
Driver API
----------
- Support timestamping on bond interfaces in active/passive mode.
- Introduce generic phylink link mode validation for drivers which
don't have any quirks and where MAC capability bits fully express
what's supported. Allow PCS layer to participate in the validation.
Convert a number of drivers.
- Add support to set/get size of buffers on the Rx rings and size of
the tx copybreak buffer via ethtool.
- Support offloading TC actions as first-class citizens rather than
only as attributes of filters, improve sharing and device resource
utilization.
- WiFi (mac80211/cfg80211):
- support forwarding offload (ndo_fill_forward_path)
- support for background radar detection hardware
- SA Query Procedures offload on the AP side
New hardware / drivers
----------------------
- tsnep - FPGA based TSN endpoint Ethernet MAC used in PLCs with
real-time requirements for isochronous communication with protocols
like OPC UA Pub/Sub.
- Qualcomm BAM-DMUX WWAN - driver for data channels of modems
integrated into many older Qualcomm SoCs, e.g. MSM8916 or
MSM8974 (qcom_bam_dmux).
- Microchip LAN966x multi-port Gigabit AVB/TSN Ethernet Switch
driver with support for bridging, VLANs and multicast forwarding
(lan966x).
- iwlmei driver for co-operating between Intel's WiFi driver and
Intel's Active Management Technology (AMT) devices.
- mse102x - Vertexcom MSE102x Homeplug GreenPHY chips
- Bluetooth:
- MediaTek MT7921 SDIO devices
- Foxconn MT7922A
- Realtek RTL8852AE
Drivers
-------
- Significantly improve performance in the datapaths of:
lan78xx, ax88179_178a, lantiq_xrx200, bnxt.
- Intel Ethernet NICs:
- igb: support PTP/time PEROUT and EXTTS SDP functions on
82580/i354/i350 adapters
- ixgbevf: new PF -> VF mailbox API which avoids the risk of
mailbox corruption with ESXi
- iavf: support configuration of VLAN features of finer granularity,
stacked tags and filtering
- ice: PTP support for new E822 devices with sub-ns precision
- ice: support firmware activation without reboot
- Mellanox Ethernet NICs (mlx5):
- expose control over IRQ coalescing mode (CQE vs EQE) via ethtool
- support TC forwarding when tunnel encap and decap happen between
two ports of the same NIC
- dynamically size and allow disabling various features to save
resources for running in embedded / SmartNIC scenarios
- Broadcom Ethernet NICs (bnxt):
- use page frag allocator to improve Rx performance
- expose control over IRQ coalescing mode (CQE vs EQE) via ethtool
- Other Ethernet NICs:
- amd-xgbe: add Ryzen 6000 (Yellow Carp) Ethernet support
- Microsoft cloud/virtual NIC (mana):
- add XDP support (PASS, DROP, TX)
- Mellanox Ethernet switches (mlxsw):
- initial support for Spectrum-4 ASICs
- VxLAN with IPv6 underlay
- Marvell Ethernet switches (prestera):
- support flower flow templates
- add basic IP forwarding support
- NXP embedded Ethernet switches (ocelot & felix):
- support Per-Stream Filtering and Policing (PSFP)
- enable cut-through forwarding between ports by default
- support FDMA to improve packet Rx/Tx to CPU
- Other embedded switches:
- hellcreek: improve trapping management (STP and PTP) packets
- qca8k: support link aggregation and port mirroring
- Qualcomm 802.11ax WiFi (ath11k):
- qca6390, wcn6855: enable 802.11 power save mode in station mode
- BSS color change support
- WCN6855 hw2.1 support
- 11d scan offload support
- scan MAC address randomization support
- full monitor mode, only supported on QCN9074
- qca6390/wcn6855: report signal and tx bitrate
- qca6390: rfkill support
- qca6390/wcn6855: regdb.bin support
- Intel WiFi (iwlwifi):
- support SAR GEO Offset Mapping (SGOM) and Time-Aware-SAR (TAS)
in cooperation with the BIOS
- support for Optimized Connectivity Experience (OCE) scan
- support firmware API version 68
- lots of preparatory work for the upcoming Bz device family
- MediaTek WiFi (mt76):
- Specific Absorption Rate (SAR) support
- mt7921: 160 MHz channel support
- RealTek WiFi (rtw88):
- Specific Absorption Rate (SAR) support
- scan offload
- Other WiFi NICs
- ath10k: support fetching (pre-)calibration data from nvmem
- brcmfmac: configure keep-alive packet on suspend
- wcn36xx: beacon filter support
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=KLm3
-----END PGP SIGNATURE-----
Merge tag '5.17-net-next' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core
----
- Defer freeing TCP skbs to the BH handler, whenever possible, or at
least perform the freeing outside of the socket lock section to
decrease cross-CPU allocator work and improve latency.
- Add netdevice refcount tracking to locate sources of netdevice and
net namespace refcount leaks.
- Make Tx watchdog less intrusive - avoid pausing Tx and restarting
all queues from a single CPU removing latency spikes.
- Various small optimizations throughout the stack from Eric Dumazet.
- Make netdev->dev_addr[] constant, force modifications to go via
appropriate helpers to allow us to keep addresses in ordered data
structures.
- Replace unix_table_lock with per-hash locks, improving performance
of bind() calls.
- Extend skb drop tracepoint with a drop reason.
- Allow SO_MARK and SO_PRIORITY setsockopt under CAP_NET_RAW.
BPF
---
- New helpers:
- bpf_find_vma(), find and inspect VMAs for profiling use cases
- bpf_loop(), runtime-bounded loop helper trading some execution
time for much faster (if at all converging) verification
- bpf_strncmp(), improve performance, avoid compiler flakiness
- bpf_get_func_arg(), bpf_get_func_ret(), bpf_get_func_arg_cnt()
for tracing programs, all inlined by the verifier
- Support BPF relocations (CO-RE) in the kernel loader.
- Further the support for BTF_TYPE_TAG annotations.
- Allow access to local storage in sleepable helpers.
- Convert verifier argument types to a composable form with different
attributes which can be shared across types (ro, maybe-null).
- Prepare libbpf for upcoming v1.0 release by cleaning up APIs,
creating new, extensible ones where missing and deprecating those
to be removed.
Protocols
---------
- WiFi (mac80211/cfg80211):
- notify user space about long "come back in N" AP responses,
allow it to react to such temporary rejections
- allow non-standard VHT MCS 10/11 rates
- use coarse time in airtime fairness code to save CPU cycles
- Bluetooth:
- rework of HCI command execution serialization to use a common
queue and work struct, and improve handling errors reported in
the middle of a batch of commands
- rework HCI event handling to use skb_pull_data, avoiding packet
parsing pitfalls
- support AOSP Bluetooth Quality Report
- SMC:
- support net namespaces, following the RDMA model
- improve connection establishment latency by pre-clearing buffers
- introduce TCP ULP for automatic redirection to SMC
- Multi-Path TCP:
- support ioctls: SIOCINQ, OUTQ, and OUTQNSD
- support socket options: IP_TOS, IP_FREEBIND, IP_TRANSPARENT,
IPV6_FREEBIND, and IPV6_TRANSPARENT, TCP_CORK and TCP_NODELAY
- support cmsgs: TCP_INQ
- improvements in the data scheduler (assigning data to subflows)
- support fastclose option (quick shutdown of the full MPTCP
connection, similar to TCP RST in regular TCP)
- MCTP (Management Component Transport) over serial, as defined by
DMTF spec DSP0253 - "MCTP Serial Transport Binding".
Driver API
----------
- Support timestamping on bond interfaces in active/passive mode.
- Introduce generic phylink link mode validation for drivers which
don't have any quirks and where MAC capability bits fully express
what's supported. Allow PCS layer to participate in the validation.
Convert a number of drivers.
- Add support to set/get size of buffers on the Rx rings and size of
the tx copybreak buffer via ethtool.
- Support offloading TC actions as first-class citizens rather than
only as attributes of filters, improve sharing and device resource
utilization.
- WiFi (mac80211/cfg80211):
- support forwarding offload (ndo_fill_forward_path)
- support for background radar detection hardware
- SA Query Procedures offload on the AP side
New hardware / drivers
----------------------
- tsnep - FPGA based TSN endpoint Ethernet MAC used in PLCs with
real-time requirements for isochronous communication with protocols
like OPC UA Pub/Sub.
- Qualcomm BAM-DMUX WWAN - driver for data channels of modems
integrated into many older Qualcomm SoCs, e.g. MSM8916 or MSM8974
(qcom_bam_dmux).
- Microchip LAN966x multi-port Gigabit AVB/TSN Ethernet Switch driver
with support for bridging, VLANs and multicast forwarding
(lan966x).
- iwlmei driver for co-operating between Intel's WiFi driver and
Intel's Active Management Technology (AMT) devices.
- mse102x - Vertexcom MSE102x Homeplug GreenPHY chips
- Bluetooth:
- MediaTek MT7921 SDIO devices
- Foxconn MT7922A
- Realtek RTL8852AE
Drivers
-------
- Significantly improve performance in the datapaths of: lan78xx,
ax88179_178a, lantiq_xrx200, bnxt.
- Intel Ethernet NICs:
- igb: support PTP/time PEROUT and EXTTS SDP functions on
82580/i354/i350 adapters
- ixgbevf: new PF -> VF mailbox API which avoids the risk of
mailbox corruption with ESXi
- iavf: support configuration of VLAN features of finer
granularity, stacked tags and filtering
- ice: PTP support for new E822 devices with sub-ns precision
- ice: support firmware activation without reboot
- Mellanox Ethernet NICs (mlx5):
- expose control over IRQ coalescing mode (CQE vs EQE) via ethtool
- support TC forwarding when tunnel encap and decap happen between
two ports of the same NIC
- dynamically size and allow disabling various features to save
resources for running in embedded / SmartNIC scenarios
- Broadcom Ethernet NICs (bnxt):
- use page frag allocator to improve Rx performance
- expose control over IRQ coalescing mode (CQE vs EQE) via ethtool
- Other Ethernet NICs:
- amd-xgbe: add Ryzen 6000 (Yellow Carp) Ethernet support
- Microsoft cloud/virtual NIC (mana):
- add XDP support (PASS, DROP, TX)
- Mellanox Ethernet switches (mlxsw):
- initial support for Spectrum-4 ASICs
- VxLAN with IPv6 underlay
- Marvell Ethernet switches (prestera):
- support flower flow templates
- add basic IP forwarding support
- NXP embedded Ethernet switches (ocelot & felix):
- support Per-Stream Filtering and Policing (PSFP)
- enable cut-through forwarding between ports by default
- support FDMA to improve packet Rx/Tx to CPU
- Other embedded switches:
- hellcreek: improve trapping management (STP and PTP) packets
- qca8k: support link aggregation and port mirroring
- Qualcomm 802.11ax WiFi (ath11k):
- qca6390, wcn6855: enable 802.11 power save mode in station mode
- BSS color change support
- WCN6855 hw2.1 support
- 11d scan offload support
- scan MAC address randomization support
- full monitor mode, only supported on QCN9074
- qca6390/wcn6855: report signal and tx bitrate
- qca6390: rfkill support
- qca6390/wcn6855: regdb.bin support
- Intel WiFi (iwlwifi):
- support SAR GEO Offset Mapping (SGOM) and Time-Aware-SAR (TAS)
in cooperation with the BIOS
- support for Optimized Connectivity Experience (OCE) scan
- support firmware API version 68
- lots of preparatory work for the upcoming Bz device family
- MediaTek WiFi (mt76):
- Specific Absorption Rate (SAR) support
- mt7921: 160 MHz channel support
- RealTek WiFi (rtw88):
- Specific Absorption Rate (SAR) support
- scan offload
- Other WiFi NICs
- ath10k: support fetching (pre-)calibration data from nvmem
- brcmfmac: configure keep-alive packet on suspend
- wcn36xx: beacon filter support"
* tag '5.17-net-next' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2048 commits)
tcp: tcp_send_challenge_ack delete useless param `skb`
net/qla3xxx: Remove useless DMA-32 fallback configuration
rocker: Remove useless DMA-32 fallback configuration
hinic: Remove useless DMA-32 fallback configuration
lan743x: Remove useless DMA-32 fallback configuration
net: enetc: Remove useless DMA-32 fallback configuration
cxgb4vf: Remove useless DMA-32 fallback configuration
cxgb4: Remove useless DMA-32 fallback configuration
cxgb3: Remove useless DMA-32 fallback configuration
bnx2x: Remove useless DMA-32 fallback configuration
et131x: Remove useless DMA-32 fallback configuration
be2net: Remove useless DMA-32 fallback configuration
vmxnet3: Remove useless DMA-32 fallback configuration
bna: Simplify DMA setting
net: alteon: Simplify DMA setting
myri10ge: Simplify DMA setting
qlcnic: Simplify DMA setting
net: allwinner: Fix print format
page_pool: remove spinlock in page_pool_refill_alloc_cache()
amt: fix wrong return type of amt_send_membership_update()
...
Merge cpuidle updates, PM core updates and one hiberation-related
update for 5.17-rc1:
- Make cpuidle use default_groups in kobj_type (Greg Kroah-Hartman).
- Fix two comments in cpuidle code (Jason Wang, Yang Li).
- Simplify locking in pm_runtime_put_suppliers() (Rafael Wysocki).
- Add safety net to supplier device release in the runtime PM core
code (Rafael Wysocki).
- Capture device status before disabling runtime PM for it (Rafael
Wysocki).
- Add new macros for declaring PM operations to allow drivers to
avoid guarding them with CONFIG_PM #ifdefs or __maybe_unused and
update some drivers to use these macros (Paul Cercueil).
- Allow ACPI hardware signature to be honoured during restore from
hibernation (David Woodhouse).
* pm-cpuidle:
cpuidle: use default_groups in kobj_type
cpuidle: Fix cpuidle_remove_state_sysfs() kerneldoc comment
cpuidle: menu: Fix typo in a comment
* pm-core:
PM: runtime: Simplify locking in pm_runtime_put_suppliers()
mmc: mxc: Use the new PM macros
mmc: jz4740: Use the new PM macros
PM: runtime: Add safety net to supplier device release
PM: runtime: Capture device status before disabling runtime PM
PM: core: Add new *_PM_OPS macros, deprecate old ones
PM: core: Redefine pm_ptr() macro
r8169: Avoid misuse of pm_ptr() macro
* pm-sleep:
PM: hibernate: Allow ACPI hardware signature to be honoured
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
Moreover, dma_set_mask_and_coherent() returns 0 or -EIO, so the return
code of the function can be used directly.
Finally, inline bnx2x_set_coherency_mask() because it is now only a wrapper
for a single dma_set_mask_and_coherent() call.
Simplify code and remove some dead code accordingly.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/29608a525876afddceabf8f11b2ba606da8748fc.1641730747.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
Moreover, dma_set_mask_and_coherent() returns 0 or -EIO, so the return
code of the function can be used directly. There is no need to 'rc = -EIO'
explicitly.
Simplify code and remove some dead code accordingly.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/b9aa46e7e5a5aa61f56aac5ea439930f41ad9946.1641726804.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
So if dma_set_mask_and_coherent() succeeds, 'netdev->features' will have
NETIF_F_HIGHDMA in all cases. Move the assignment of this feature in
be_netdev_init() instead be_probe() which is a much logical place.
Simplify code and remove some dead code accordingly.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/637696d7141faa68c29fc34b70f9aa67d5e605f0.1641718999.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As stated in [1], dma_set_mask() with a 64-bit mask will never fail if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
So, if dma_set_mask_and_coherent() succeeds, 'using_dac' is known to be
'true'. This variable can be removed.
Simplify code and remove some dead code accordingly.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/1d5a7b3f4fa735f1233c3eb3fa07e71df95fad75.1641658516.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As stated in [1], dma_set_mask() with a 64-bit mask will never fail if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
If dma_set_mask_and_coherent() succeeds, 'ap->pci_using_dac' is known to be
1. So 'pci_using_dac' can be removed from the 'struct ace_private'.
Simplify code and remove some dead code accordingly.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/1a414c05c27b21c661aef61dffe1adcd1578b1f5.1641651917.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As stated in [1], dma_set_mask() with a 64-bit mask will never fail if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
So qlcnic_set_dma_mask(), (in qlcnic_main.c) can be simplified a lot and
inlined directly in its only caller.
If dma_set_mask_and_coherent() succeeds, 'pci_using_dac' is known to be 1.
So it can be removed from all the calling chain.
qlcnic_setup_netdev() can finally be simplified as-well.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/4996ab0337d62ec6a54b2edf234cd5ced4b4d7ad.1641649611.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kees reports quoted commit introduced the following warning on arm64:
drivers/net/ethernet/allwinner/sun4i-emac.c:922:60: error: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'resource_size_t' {aka 'long long unsigned int'} [-Werror=format=]
922 | netdev_info(ndev, "get io resource from device: 0x%x, size = %u\n",
| ~^
| | | unsigned int
| %llx
923 | regs->start, resource_size(regs));
| ~~~~~~~~~~~
| |
| resource_size_t {aka long long unsigned int}
.. and another one like that for resource_size().
Switch to %pa and a cast.
Reported-by: Kees Cook <keescook@chromium.org>
Fixes: 47869e82c8 ("sun4i-emac.c: add dma support")
Link: https://lore.kernel.org/r/20220108034438.2227343-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
amt_send_membership_update() would return -1 but it's return type is bool.
So, it should be used TRUE instead of -1.
Fixes: cbc21dc1cf ("amt: add data plane of amt interface")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Link: https://lore.kernel.org/r/20220109163702.6331-1-ap420073@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Syzbot reported uninit value in mcs7830_bind(). The problem was in
missing validation check for bytes read via usbnet_read_cmd().
usbnet_read_cmd() internally calls usb_control_msg(), that returns
number of bytes read. Code should validate that requested number of bytes
was actually read.
So, this patch adds missing size validation check inside
mcs7830_get_reg() to prevent uninit value bugs
Reported-and-tested-by: syzbot+003c0a286b9af5412510@syzkaller.appspotmail.com
Fixes: 2a36d70834 ("USB: driver for mcs7830 (aka DeLOCK) USB ethernet adapter")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20220106225716.7425-1-paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Build bot reports:
drivers/net/ethernet/mellanox/mlx5/core/en_stats.c: In function 'fec_set_block_stats':
drivers/net/ethernet/mellanox/mlx5/core/en_stats.c:1235:48: error: 'outl' undeclared (first use in this function); did you mean 'out'?
1235 | if (mlx5_core_access_reg(mdev, in, sz, outl, sz, MLX5_REG_PPCNT, 0, 0))
| ^~~~
| out
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20220109213321.2292830-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While it has always been possible to infer that an HWRM command was
abandoned due to an unhealthy firmware status by the shortened timeout
reported, this change improves the log messaging to account for this
case explicitly. In the interests of further clarity, the firmware
status is now also reported in these new messages.
v2: Remove inline keyword for hwrm_wait_must_abort() in .c file.
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some older devices cannot accommodate the 40 seconds timeout
cap for long running commands (such as NVRAM commands) due to
hardware limitations. Allow these devices to request more time for
these long running commands, but print a warning, since the longer
timeout may cause the hung task watchdog to trigger. In the case of a
firmware update operation, this is preferable to failing outright.
v2: Use bp->hwrm_cmd_max_timeout directly without the constants.
Fixes: 881d8353b0 ("bnxt_en: Add an upper bound for all firmware command timeouts.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current driver design relies on the PF netdev being open in order
to intercept the following HWRM commands from a VF:
- HWRM_FUNC_VF_CFG
- HWRM_CFA_L2_FILTER_ALLOC
- HWRM_PORT_PHY_QCFG (only if FW_CAP_LINK_ADMIN is not supported)
If the PF is closed, then VFs are subjected to rather inscrutable error
messages in response to any configuration requests involving the above
command types. Recent firmware distinguishes this problem case from
other errors by returning HWRM_ERR_CODE_PF_UNAVAILABLE. In most cases,
the appropriate course of action is still to fail, but this can now be
accomplished with the aid of more user informative log messages. For L2
filter allocations that are already asynchronous, an automatic retry
seems more appropriate.
v2: Delete extra newline.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add logging of firmware messages. These can be useful for diagnosing
issues in the field, but due to their verbosity are only appropriate
at a debug message level.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When building ARCH=arm allmodconfig:
drivers/net/wireless/intel/iwlwifi/mvm/ftm-initiator.c: In function ‘iwl_mvm_ftm_rtt_smoothing’:
./include/asm-generic/div64.h:222:35: error: comparison of distinct pointer types lacks a cast [-Werror]
222 | (void)(((typeof((n)) *)0) == ((uint64_t *)0)); \
| ^~
drivers/net/wireless/intel/iwlwifi/mvm/ftm-initiator.c:1070:9: note: in expansion of macro ‘do_div’
1070 | do_div(rtt_avg, 100);
| ^~~~~~
do_div() has to be used with an unsigned 64-bit integer dividend but
rtt_avg is a signed 64-bit integer.
div_s64() expects a signed 64-bit integer dividend and signed 32-bit
divisor, which fits this scenario, so use that function here to fix the
warning.
Fixes: 8b0f92549f ("iwlwifi: mvm: fix 32-bit build in FTM")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20211227191757.2354329-1-nathan@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
No information is deliberately sent in hf->flags in host -> device
communications, but the open-source candleLight firmware echoes it
back, which can result in the GS_CAN_FLAG_OVERFLOW flag being set and
generating spurious ERRORFRAMEs.
While there also initialize the reserved member with 0.
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/all/20220106002952.25883-1-brian.silverman@bluerivertech.com
Link: https://github.com/candle-usb/candleLight_fw/issues/87
Cc: stable@vger.kernel.org
Signed-off-by: Brian Silverman <brian.silverman@bluerivertech.com>
[mkl: initialize the reserved member, too]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Make sure we free CAN network device in the error path. There are
several jumps to fail label after allocating the CAN network device
successfully. This patch places the free_candev() under fail label so
that in failure path a jump to fail label frees the CAN network
device.
Fixes: 76e9353a80 ("can: rcar_canfd: Add support for RZ/G2L family")
Link: https://lore.kernel.org/all/20220106114801.20563-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
For the possible failure of the platform_get_irq(), the returned irq
could be error number and will finally cause the failure of the
request_irq().
Consider that platform_get_irq() can now in certain cases return
-EPROBE_DEFER, and the consequences of letting request_irq()
effectively convert that into -EINVAL, even at probe time rather than
later on. So it might be better to check just now.
Fixes: b1201e44f5 ("can: xilinx CAN controller support")
Link: https://lore.kernel.org/all/20211224021324.1447494-1-jiasheng@iscas.ac.cn
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In the function softing_startstop() the variable error_reporting is
assigned but not used. The code that uses this variable is commented
out. Its stated that the functionality is not finally verified.
To fix the warning:
| drivers/net/can/softing/softing_fw.c:424:9: error: variable 'error_reporting' set but not used [-Werror,-Wunused-but-set-variable]
remove the comment, activate the code, but add a "0 &&" to the if
expression and rely on the optimizer rather than the preprocessor to
remove the code.
Link: https://lore.kernel.org/all/20220109103126.1872833-1-mkl@pengutronix.de
Fixes: 03fd3cf5a1 ("can: add driver for Softing card")
Cc: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In case device registration fails during probe, the driver state and
the embedded platform device structure needs to be freed using
platform_device_put() to properly free all resources (e.g. the device
name).
Fixes: 0a0b7a5f7a ("can: add driver for Softing card")
Link: https://lore.kernel.org/all/20211222104843.6105-1-johan@kernel.org
Cc: stable@vger.kernel.org # 2.6.38
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds ethtool support to get the number of message buffers
configured for reception/transmission, which may also depends on
runtime configurations such as the 'rx-rtr' flag state.
Link: https://lore.kernel.org/all/20220108181633.420433-1-dario.binacchi@amarulasolutions.com
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
[mkl: port to net-next/master, replace __sw_hweight64 by simpler calculation]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds a private flag to the flexcan driver to switch the
"rx-rtr" setting on and off.
"rx-rtr" on - Receive RTR frames. (default)
The CAN controller can and will receive RTR frames.
On some IP cores the controller cannot receive RTR
frames in the more performant "RX mailbox" mode and
will use "RX FIFO" mode instead.
"rx-rtr" off - Waive ability to receive RTR frames. (not supported on all IP cores)
This mode activates the "RX mailbox mode" for better
performance, on some IP cores RTR frames cannot be
received anymore.
The "RX FIFO" mode uses a FIFO with a depth of 6 CAN frames.
The "RX mailbox" mode uses up to 62 mailboxes.
Link: https://lore.kernel.org/all/20220107193105.1699523-6-mkl@pengutronix.de
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Co-developed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Most flexcan IP cores support 2 RX modes:
- FIFO
- mailbox
Some IP core versions cannot receive CAN RTR messages via mailboxes.
This patch adds quirks to document this.
This information will be used in a later patch to switch from FIFO to
more performant mailbox mode at the expense of losing the ability to
receive RTR messages. This trade off is beneficial in certain use
cases.
Link: https://lore.kernel.org/all/20220107193105.1699523-5-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Most flexcan IP cores support 2 RX modes:
- FIFO
- mailbox
The names for these modes were chosen to reflect the name of the
rx-offload mode they are using.
The name of the RX modes should better reflect their difference with
regards the flexcan IP core. So this patch renames the various
occurrences of OFF_FIFO to RX_FIFO and OFF_TIMESTAMP to RX_MAILBOX:
| FLEXCAN_TX_MB_RESERVED_OFF_FIFO -> FLEXCAN_TX_MB_RESERVED_RX_FIFO
| FLEXCAN_TX_MB_RESERVED_OFF_TIMESTAMP -> FLEXCAN_TX_MB_RESERVED_RX_MAILBOX
| FLEXCAN_QUIRK_USE_OFF_TIMESTAMP -> FLEXCAN_QUIRK_USE_RX_MAILBOX
Link: https://lore.kernel.org/all/20220107193105.1699523-4-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This is a preparation patch for the upcoming support to change the
rx-rtr capability via the ethtool API.
Link: https://lore.kernel.org/all/20220107193105.1699523-3-mkl@pengutronix.de
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .c files in the Makefile are ordered alphabetically. This patch
groups the function prototypes by their corresponding .c file and
brings the into the same order.
Link: https://lore.kernel.org/all/20220105154300.1258636-8-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
A RX overflow usually happens during high system load. Printing
overflow messages to the kernel log, which on embedded systems often
is outputted on the serial console, even increases the system load.
To decrease the system load in these situations, denote the messages
to debug level and wrap them with net_ratelimit().
Link: https://lore.kernel.org/all/20220105154300.1258636-7-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
With patch
| dd8088d5a8 PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter
the usual pm_runtime_get_sync() and pm_runtime_put_noidle()
in-case-of-error dance is no longer needed. Convert the mcp251xfd
driver to use this function.
Link: https://lore.kernel.org/all/20220105154300.1258636-6-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch exchanges the order of open_candev() and
pm_runtime_get_sync(), so that open_candev() is called first.
A usual reason why open_candev() fails is missing CAN bit rate
configuration. It makes no sense to resume the device from PM sleep
first just to put it to sleep if the bit rate is not configured.
Link: https://lore.kernel.org/all/20220105154300.1258636-5-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Clang static analysis reports this problem
janz-ican3.c:1311:2: warning: Undefined or garbage value returned to caller
return dlc;
^~~~~~~~~~
dlc is only set with this conditional
if (!(cf->can_id & CAN_RTR_FLAG))
dlc = cf->len;
But is always returned. So initialize dlc to 0.
Fixes: cc4b08c31b ("can: do not increase tx_bytes statistics for RTR frames")
Link: https://lore.kernel.org/all/20220108143319.3986923-1-trix@redhat.com
Signed-off-by: Tom Rix <trix@redhat.com>
Acked-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Create an inline function for resetting the driver
to reduce code duplication.
Signed-off-by: Nati Koler <nkoler@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Changed bad_csum to csum_bad to align with csum_unchecked & csum_good
Signed-off-by: Nati Koler <nkoler@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add qid and req_id to error prints when ENA_REGS_RESET_INV_TX_REQ_ID
reset occurs.
Switch from %hu to %u, since u16 should be printed with %u, as
explained in [1].
[1] - https://www.kernel.org/doc/html/latest/core-api/printk-formats.html
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This struct was used to pass data from callee function to its caller.
Its usage can be avoided.
Removing it results in less code without any damage to code readability.
Also it allows to consolidate ring size calculation into a single
function (ena_calc_io_queue_size()).
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The print that indicates that device reset has finished is
currently called from ena_restore_device().
Move it to ena_fw_reset_device() as it is the more natural
location for it.
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ena_com_indirect_table_fill_entry() function only returns -EINVAL
or 0, no need to check for -EOPNOTSUPP.
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the capabilities field to query the device for ENI stats
support.
This replaces the previous method that tried to get the ENI stats
during ena_probe() and used the success or failure as an indication
for support by the device.
Remove eni_stats_supported field from struct ena_adapter. This field
was used for the previous method of queriying for ENI stats support.
Change the severity level of the print in case of
ena_com_get_eni_stats() failure from info to error.
With the previous method of querying form ENI stats support, failure
to get ENI stats was normal for devices that don't support it.
With the use of the capabilities field such a failure is unexpected,
as it is called only if the device reported that it supports ENI
stats.
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This bitmask field indicates what capabilities are supported by the
device.
The capabilities field differs from the 'supported_features' field which
indicates what sub-commands for the set/get feature commands are
supported. The sub-commands are specified in the 'feature_id' field of
the 'ena_admin_set_feat_cmd' struct in the following way:
struct ena_admin_set_feat_cmd cmd;
cmd.aq_common_descriptor.opcode = ENA_ADMIN_SET_FEATURE;
cmd.feat_common.feature_
The 'capabilities' field, on the other hand, specifies different
capabilities of the device. For example, whether the device supports
querying of ENI stats.
Also add an enumerator which contains all the capabilities. The
first added capability macro is for ENI stats feature.
Capabilities are queried along with the other device attributes (in
ena_com_get_dev_attr_feat()) during device initialization and are stored
in the ena_com_dev struct. They can be later queried using the
ena_com_get_cap() helper function.
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ena_calc_io_queue_size() always returns 0, therefore make it a
void function and update the calling function to stop checking
the return value.
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for flushing the MAC table on a given port in the ocelot
switch library, and use this functionality in the felix DSA driver.
This operation is needed when a port leaves a bridge to become
standalone, and when the learning is disabled, and when the STP state
changes to a state where no FDB entry should be present.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220107144229.244584-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Assuming the test setup described here:
https://patchwork.kernel.org/project/netdevbpf/cover/20210205130240.4072854-1-vladimir.oltean@nxp.com/
(swp1 and swp2 are in bond0, and bond0 is in a bridge with swp0)
it can be seen that when swp1 goes down (on either board A or B), then
traffic that should go through that port isn't forwarded anywhere.
A dump of the PGID table shows the following:
PGID_DST[0] = ports 0
PGID_DST[1] = ports 1
PGID_DST[2] = ports 2
PGID_DST[3] = ports 3
PGID_DST[4] = ports 4
PGID_DST[5] = ports 5
PGID_DST[6] = no ports
PGID_AGGR[0] = ports 0, 1, 2, 3, 4, 5
PGID_AGGR[1] = ports 0, 1, 2, 3, 4, 5
PGID_AGGR[2] = ports 0, 1, 2, 3, 4, 5
PGID_AGGR[3] = ports 0, 1, 2, 3, 4, 5
PGID_AGGR[4] = ports 0, 1, 2, 3, 4, 5
PGID_AGGR[5] = ports 0, 1, 2, 3, 4, 5
PGID_AGGR[6] = ports 0, 1, 2, 3, 4, 5
PGID_AGGR[7] = ports 0, 1, 2, 3, 4, 5
PGID_AGGR[8] = ports 0, 1, 2, 3, 4, 5
PGID_AGGR[9] = ports 0, 1, 2, 3, 4, 5
PGID_AGGR[10] = ports 0, 1, 2, 3, 4, 5
PGID_AGGR[11] = ports 0, 1, 2, 3, 4, 5
PGID_AGGR[12] = ports 0, 1, 2, 3, 4, 5
PGID_AGGR[13] = ports 0, 1, 2, 3, 4, 5
PGID_AGGR[14] = ports 0, 1, 2, 3, 4, 5
PGID_AGGR[15] = ports 0, 1, 2, 3, 4, 5
PGID_SRC[0] = ports 1, 2
PGID_SRC[1] = ports 0
PGID_SRC[2] = ports 0
PGID_SRC[3] = no ports
PGID_SRC[4] = no ports
PGID_SRC[5] = no ports
PGID_SRC[6] = ports 0, 1, 2, 3, 4, 5
Whereas a "good" PGID configuration for that setup should have looked
like this:
PGID_DST[0] = ports 0
PGID_DST[1] = ports 1, 2
PGID_DST[2] = ports 1, 2
PGID_DST[3] = ports 3
PGID_DST[4] = ports 4
PGID_DST[5] = ports 5
PGID_DST[6] = no ports
PGID_AGGR[0] = ports 0, 2, 3, 4, 5
PGID_AGGR[1] = ports 0, 2, 3, 4, 5
PGID_AGGR[2] = ports 0, 2, 3, 4, 5
PGID_AGGR[3] = ports 0, 2, 3, 4, 5
PGID_AGGR[4] = ports 0, 2, 3, 4, 5
PGID_AGGR[5] = ports 0, 2, 3, 4, 5
PGID_AGGR[6] = ports 0, 2, 3, 4, 5
PGID_AGGR[7] = ports 0, 2, 3, 4, 5
PGID_AGGR[8] = ports 0, 2, 3, 4, 5
PGID_AGGR[9] = ports 0, 2, 3, 4, 5
PGID_AGGR[10] = ports 0, 2, 3, 4, 5
PGID_AGGR[11] = ports 0, 2, 3, 4, 5
PGID_AGGR[12] = ports 0, 2, 3, 4, 5
PGID_AGGR[13] = ports 0, 2, 3, 4, 5
PGID_AGGR[14] = ports 0, 2, 3, 4, 5
PGID_AGGR[15] = ports 0, 2, 3, 4, 5
PGID_SRC[0] = ports 1, 2
PGID_SRC[1] = ports 0
PGID_SRC[2] = ports 0
PGID_SRC[3] = no ports
PGID_SRC[4] = no ports
PGID_SRC[5] = no ports
PGID_SRC[6] = ports 0, 1, 2, 3, 4, 5
In other words, in the "bad" configuration, the attempt is to remove the
inactive swp1 from the destination ports via PGID_DST. But when a MAC
table entry is learned, it is learned towards PGID_DST 1, because that
is the logical port id of the LAG itself (it is equal to the lowest
numbered member port). So when swp1 becomes inactive, if we set
PGID_DST[1] to contain just swp1 and not swp2, the packet will not have
any chance to reach the destination via swp2.
The "correct" way to remove swp1 as a destination is via PGID_AGGR
(remove swp1 from the aggregation port groups for all aggregation
codes). This means that PGID_DST[1] and PGID_DST[2] must still contain
both swp1 and swp2. This makes the MAC table still treat packets
destined towards the single-port LAG as "multicast", and the inactive
ports are removed via the aggregation code tables.
The change presented here is a design one: the ocelot_get_bond_mask()
function used to take an "only_active_ports" argument. We don't need
that. The only call site that specifies only_active_ports=true,
ocelot_set_aggr_pgids(), must retrieve the entire bonding mask, because
it must program that into PGID_DST. Additionally, it must also clear the
inactive ports from the bond mask here, which it can't do if bond_mask
just contains the active ports:
ac = ocelot_read_rix(ocelot, ANA_PGID_PGID, i);
ac &= ~bond_mask; <---- here
/* Don't do division by zero if there was no active
* port. Just make all aggregation codes zero.
*/
if (num_active_ports)
ac |= BIT(aggr_idx[i % num_active_ports]);
ocelot_write_rix(ocelot, ac, ANA_PGID_PGID, i);
So it becomes the responsibility of ocelot_set_aggr_pgids() to take
ocelot_port->lag_tx_active into consideration when populating the
aggr_idx array.
Fixes: 23ca3b727e ("net: mscc: ocelot: rebalance LAGs on link up/down events")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220107164332.402133-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The variable `ret_code' used for returning is never changed in function
`iavf_shutdown_adminq'. So that it can be removed and just return its
initial value 0 at the end of `iavf_shutdown_adminq' function.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The code that uses variables pe_cntx_size and pe_filt_size
has been removed, so they should be removed as well.
Eliminate the following clang warnings:
drivers/net/ethernet/intel/i40e/i40e_common.c:4139:20:
warning: variable 'pe_filt_size' set but not used.
drivers/net/ethernet/intel/i40e/i40e_common.c:4139:6:
warning: variable 'pe_cntx_size' set but not used.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove non-inclusive language from the driver.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The i40e_asq_send_command will now use a non blocking usleep_range if
possible (non-atomic context), instead of busy-waiting udelay. The
usleep_range function uses hrtimers to provide better performance and
removes the negative impact of busy-waiting in time-critical
environments.
1. Rename i40e_asq_send_command to i40e_asq_send_command_atomic
and add 5th parameter to inform if called from an atomic context.
Call inside usleep_range (if non-atomic) or udelay (if atomic).
2. Change i40e_asq_send_command to invoke
i40e_asq_send_command_atomic(..., false).
3. Change two functions:
- i40e_aq_set_vsi_uc_promisc_on_vlan
- i40e_aq_set_vsi_mc_promisc_on_vlan
to explicitly use i40e_asq_send_command_atomic(..., true)
instead of i40e_asq_send_command, as they use spinlocks and do some
work in an atomic context.
All other calls to i40e_asq_send_command remain unchanged.
Signed-off-by: Dawid Lukwinski <dawid.lukwinski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Trusted VF can use up every resource available, leaving nothing
to other trusted VFs.
Introduce define, which calculates MacVlan resources available based
on maximum available MacVlan resources, bare minimum for each VF and
number of currently allocated VFs.
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When a VF is removed respective PTP resources are not
being freed currently. This patch fixes it.
Fixes: 43510ef4dd ("octeontx2-nicvf: Add PTP hardware clock support to NIX VF")
Signed-off-by: Rakesh Babu Saladi <rsaladi2@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before using the ptp pci device by AF driver increment
the reference count of it.
Fixes: a8b90c9d26 ("octeontx2-af: Add PTP device id for CN10K and 95O silcons")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Expose FEC per lane block counters via ethtool
2) Trivial fixes/updates/cleanup to mlx5e netdev driver
3) Fix htmldoc build warning
4) Spread mlx5 SFs (sub-functions) to all available CPU cores: Commits 1..5
Shay Drory Says:
================
Before this patchset, mlx5 subfunction shared the same IRQs (MSI-X) with
their peers subfunctions, causing them to use same CPU cores.
In large scale, this is very undesirable, SFs use small number of cpu
cores and all of them will be packed on the same CPU cores, not
utilizing all CPU cores in the system.
In this patchset we want to achieve two things.
a) Spread IRQs used by SFs to all cpu cores
b) Pack less SFs in the same IRQ, will result in multiple IRQs per core.
In this patchset, we spread SFs over all online cpus available to mlx5
irqs in Round-Robin manner. e.g.: Whenever a SF is created, pick the next
CPU core with least number of SF IRQs bound to it, SFs will share IRQs on
the same core until a certain limit, when such limit is reached, we
request a new IRQ and add it to that CPU core IRQ pool, when out of IRQs,
pick any IRQ with least number of SF users.
This enhancement is done in order to achieve a better distribution of
the SFs over all the available CPUs, which reduces application latency,
as shown bellow.
Machine details:
Intel(R) Xeon(R) CPU E5-2697 v3 @ 2.60GHz with 56 cores.
PCI Express 3 with BW of 126 Gb/s.
ConnectX-5 Ex; EDR IB (100Gb/s) and 100GbE; dual-port QSFP28; PCIe4.0
x16.
Base line test description:
Single SF on the system. One instance of netperf is running on-top the
SF.
Numbers: latency = 15.136 usec, CPU Util = 35%
Test description:
There are 250 SFs on the system. There are 3 instances of netperf
running, on-top three different SFs, in parallel.
Perf numbers:
# netperf SFs latency(usec) latency CPU utilization
affinity affinity (lower is better) increase %
1 cpu=0 cpu={0} ~23 (app 1-3) 35% 75%
2 cpu=0,2,4 cpu={0} app 1: 21.625 30% 68% (CPU 0)
app 2-3: 16.5 9% 15% (CPU 2,4)
3 cpu=0 cpu={0,2,4} app 1: ~16 7% 84% (CPU 0)
app 2-3: ~17.9 14% 22% (CPU 2,4)
4 cpu=0,2,4 cpu={0,2,4} 15.2 (app 1-3) 0% 33% (CPU 0,2,4)
- The first two entries (#1 and #2) show current state. e.g.: SFs are
using the same CPU. The last two entries (#3 and #4) shows the latency
reduction improvement of this patch. e.g.: SFs are on different CPUs.
- Whenever we use several CPUs, in case there is a different CPU
utilization, write the utilization of each CPU separately.
- Whenever the latency result of the netperf instances were different,
write the latency of each netperf instances separately.
Commands:
- for netperf CPU=0:
$ for i in {1..3}; do taskset -c 0 netperf -H 1${i}.1.1.1 -t TCP_RR -- \
-o RT_LATENCY -r8 & done
- for netperf CPU=0,2,4
$ for i in {1..3}; do taskset -c $(( ($i - 1) * 2 )) netperf -H \
1${i}.1.1.1 -t TCP_RR -- -o RT_LATENCY -r8 & done
================
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmHXh+AACgkQSD+KveBX
+j68fQgAghUX4TFS2JSwa7+XSCtzz7GIu2Xrz8aWTAnydRLlNXuFuuHYcNed6I0l
7DaVOZwHp1tp3tnx3WMGPUU6ujDPEgasaDDblvG2UXix5LPVEHDXY44ittQX8mpC
SC8Yj9mNo6DSfOMUZklFDMbw57XuLJ+HEGnwnrOEEyLX7ruDXGEViUmVBd4IoC3B
F2fJHBkdTJfHWTJRB4pWbZD1dw7WbKd0RyPla3OkoHugEUCKnbjii8cMwNM64Bbp
Pjz/SiShVy+NTotqPzRNjcx7y4tHOXCYt33zt1VlGtdUxs5eCA5jkjHFz0jb12Lu
rvfHaBaU+elMKTw5G/WMGJxZQx0kEQ==
=VBWY
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2022-01-06' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2022-01-06
1) Expose FEC per lane block counters via ethtool
2) Trivial fixes/updates/cleanup to mlx5e netdev driver
3) Fix htmldoc build warning
4) Spread mlx5 SFs (sub-functions) to all available CPU cores: Commits 1..5
Shay Drory Says:
================
Before this patchset, mlx5 subfunction shared the same IRQs (MSI-X) with
their peers subfunctions, causing them to use same CPU cores.
In large scale, this is very undesirable, SFs use small number of cpu
cores and all of them will be packed on the same CPU cores, not
utilizing all CPU cores in the system.
In this patchset we want to achieve two things.
a) Spread IRQs used by SFs to all cpu cores
b) Pack less SFs in the same IRQ, will result in multiple IRQs per core.
In this patchset, we spread SFs over all online cpus available to mlx5
irqs in Round-Robin manner. e.g.: Whenever a SF is created, pick the next
CPU core with least number of SF IRQs bound to it, SFs will share IRQs on
the same core until a certain limit, when such limit is reached, we
request a new IRQ and add it to that CPU core IRQ pool, when out of IRQs,
pick any IRQ with least number of SF users.
This enhancement is done in order to achieve a better distribution of
the SFs over all the available CPUs, which reduces application latency,
as shown bellow.
Machine details:
Intel(R) Xeon(R) CPU E5-2697 v3 @ 2.60GHz with 56 cores.
PCI Express 3 with BW of 126 Gb/s.
ConnectX-5 Ex; EDR IB (100Gb/s) and 100GbE; dual-port QSFP28; PCIe4.0
x16.
Base line test description:
Single SF on the system. One instance of netperf is running on-top the
SF.
Numbers: latency = 15.136 usec, CPU Util = 35%
Test description:
There are 250 SFs on the system. There are 3 instances of netperf
running, on-top three different SFs, in parallel.
Perf numbers:
# netperf SFs latency(usec) latency CPU utilization
affinity affinity (lower is better) increase %
1 cpu=0 cpu={0} ~23 (app 1-3) 35% 75%
2 cpu=0,2,4 cpu={0} app 1: 21.625 30% 68% (CPU 0)
app 2-3: 16.5 9% 15% (CPU 2,4)
3 cpu=0 cpu={0,2,4} app 1: ~16 7% 84% (CPU 0)
app 2-3: ~17.9 14% 22% (CPU 2,4)
4 cpu=0,2,4 cpu={0,2,4} 15.2 (app 1-3) 0% 33% (CPU 0,2,4)
- The first two entries (#1 and #2) show current state. e.g.: SFs are
using the same CPU. The last two entries (#3 and #4) shows the latency
reduction improvement of this patch. e.g.: SFs are on different CPUs.
- Whenever we use several CPUs, in case there is a different CPU
utilization, write the utilization of each CPU separately.
- Whenever the latency result of the netperf instances were different,
write the latency of each netperf instances separately.
Commands:
- for netperf CPU=0:
$ for i in {1..3}; do taskset -c 0 netperf -H 1${i}.1.1.1 -t TCP_RR -- \
-o RT_LATENCY -r8 & done
- for netperf CPU=0,2,4
$ for i in {1..3}; do taskset -c $(( ($i - 1) * 2 )) netperf -H \
1${i}.1.1.1 -t TCP_RR -- -o RT_LATENCY -r8 & done
================
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2022-01-06
Victor adds restoring of advanced rules after reset.
Wojciech improves usage of switchdev control VSI by utilizing the
device's advanced rules for forwarding.
Christophe Jaillet removes some unneeded calls to zero bitmaps, changes
some bitmap operations that don't need to be atomic, and converts a
kfree() to a more appropriate bitmap_free().
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: Use bitmap_free() to free bitmap
ice: Optimize a few bitmap operations
ice: Slightly simply ice_find_free_recp_res_idx
ice: improve switchdev's slow-path
ice: replay advanced rules after reset
====================
Link: https://lore.kernel.org/r/20220106183013.3777622-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extend existing driver for Spectrum, Spectrum-2 and Spectrum-3 ASICs
to support Spectrum-4 ASIC as well.
Currently there is no released firmware version for Spectrum-4, so the
driver is not enforcing a minimum version.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Spectrum-4 will calculate hash function for bloom filter differently
from the existing ASICs.
First, two hash functions will be used to calculate 16 bits result.
The final result will be combination of the two results - 6 bits which
are result of CRC-6 will be used as MSB and 10 bits which are result of
CRC-10 will be used as LSB.
Second, while in Spectrum{2,3}, there is a padding in each chunk, so the
chunks use a sequence of whole bytes, in Spectrum-4 there is no padding,
so each chunk use 20 bytes minus 2 bits, so it is necessary to align the
chunks to be without holes.
Add dedicated 'mlxsw_sp_acl_bf_ops' for Spectrum-4 and add the required
tables for CRC calculations.
All the details are documented as part of the code for future use.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Spectrum-4 will calculate hash function for bloom filter differently from
the existing ASICs.
There are two changes:
1. Instead of using one hash function to calculate 16 bits output (CRC-16),
two functions will be used.
2. The chunks will be built differently, without padding.
As preparation for support of Spectrum-4 bloom filter, add 'ops'
structure to allow handling different calculation for different ASICs.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Spectrum-4 will calculate hash function for bloom filter differently from
the existing ASICs.
There are two changes:
1. Instead of using one hash function to calculate 16 bits output (CRC-16),
two functions will be used.
2. The chunks will be built differently, without padding.
As preparation for support of Spectrum-4 bloom filter, rename CRC table
to include "sp2" prefix and "crc16", as next patch will add two additional
tables. In addition, rename all the dedicated functions and defines for
Spectrum-{2,3} to include "sp2" prefix.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Spectrum-4 will calculate hash function for bloom filter differently from
the existing ASICs.
One of the changes is related to the way that the chunks will be build -
without padding.
As preparation for support of Spectrum-4 bloom filter, make
mlxsw_sp_acl_bf_key_encode() more flexible, so it will be able to use it
for Spectrum-4 as well.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, mlxsw_sp_acl_bf_rule_count_index_get() is implemented before
mlxsw_sp_acl_bf_index_get() but is used after it.
Adding a new function for Spectrum-4 would make them further apart still.
Fix by moving them around.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Spectrum-4 ASIC will support more virtual routers and local ports
compared to the existing ASICs. Therefore, the virtual router and local
port ACL key elements need to be increased.
Introduce new key elements for Spectrum-4 to be aligned with the elements
used already for other Spectrum ASICs.
The key blocks layout is the same for Spectrum-4, so use the existing
code for encode_block() and clear_block(), just create separate blocks.
Note that size of `VIRT_ROUTER_MSB` is 4 bits in Spectrum-4,
therefore declare it using `MLXSW_AFK_ELEMENT_INST_U32()`, in order to
be able to set `.avoid_size_check` to true.
Otherwise, `mlxsw_afk_blocks_check()` will fail and warn.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In Spectrum-4, the size of the virtual router ACL key element increased
from 11 bits to 12 bits.
In order to reuse the existing virtual router ACL key element
enumerators for Spectrum-4, rename 'VIRT_ROUTER_8_10' and
'VIRT_ROUTER_0_7' to 'VIRT_ROUTER_MSB' and 'VIRT_ROUTER_LSB',
respectively.
No functional changes intended.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before accessing the port private structure make sure that there is
still a non-NULL pointer there. A NULL pointer access can happen when we
are on the remove path, some switch ports are unregistered and some are
in the process of unregistering.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We could get into a situation when the fwnode of the parent device is
not yet set because its probe didn't yet finish. When this happens, any
caller of the dpaa2_mac_open() will not have the fwnode available, thus
cause problems at the PHY connect time.
Avoid this by just returning -EPROBE_DEFER from the dpaa2_mac_open when
this happens.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The parent pointer node handler must be declared with a NULL
initializer. Before using it, a check must be performed to make
sure that a valid address has been assigned to it.
Signed-off-by: Robert-Ionut Alexa <robert-ionut.alexa@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Yevhen Orlov