Use DEFINE_PCI_DEVICE_TABLE() to make PCI device ids go to
.devinit.rodata section, so they can be discarded in some cases,
and make them const.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace all DMA_28BIT_MASK macro with DMA_BIT_MASK(28)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all tasklet_hi_schedule() callers with the normal
tasklet_schedule(). The former often causes troubles with
RT-kernels, and has actually no merit.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Kill snd_assert() in sound/pci/*, either removed or replaced with
if () with snd_BUG_ON().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The maestro3 driver is byte-swapping its firmware to be host-endian in
advance, when it doesn't seem to be necessary -- we could just use
le16_to_cpu() as we load it.
Doing that means that we need to switch the in-tree firmware to be
little-endian too.
Take the least intrusive way of doing this, which is to switch the
existing snd_m3_convert_from_le() function to convert _to_ little-endian
instead, and use it on the in-tree firmware instead of the loaded
firmware. It's a bit suboptimal but doesn't matter much right now
because we're about to remove the special cases for the in-tree version
anyway.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Make the hw volume buttons work correctly on some HP OmniBook laptops.
The original quirk was apparently applied a bit too early and it was
also lacking some critial register writes. This improved sequence was
discovered by trial and error (like the original sequence). Tested and
found working on OB500 and OB6000 laptops.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
free_irq() calls synchronize_irq() for you, so there is no need for
drivers to manually do the same thing (again). Thus, calls where
sync-irq immediately precedes free-irq can be simplified.
However, during this audit several bugs were noticed, where free-irq is
preceded by a "irq >= 0" check... but the sync-irq call is not covered
by the same check.
So, where sync-irq could not be eliminated completely, the missing check
was added.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
change id to elem_id as it is used to initialize each mixer element
sound/pci/maestro3.c:2071:25: warning: symbol 'id' shadows an earlier one
sound/pci/maestro3.c:67:13: originally declared here
index is used in each of these places to count over the dsp's memory,
change to the name dsp_index
sound/pci/maestro3.c:2572:9: warning: symbol 'index' shadows an earlier one
sound/pci/maestro3.c:66:12: originally declared here
sound/pci/maestro3.c:2604:9: warning: symbol 'index' shadows an earlier one
sound/pci/maestro3.c:66:12: originally declared here
[tiwai - fixed coding style issues as well]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This header file exists only for some hacks to adapt alsa-driver
tree. It's useless for building in the kernel. Let's move a few
lines in it to sound/core.h and remove it.
With this patch, sound/driver.h isn't removed but has just a single
compile warning to include it. This should be really killed in
future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Remove line duplications in defines.
Acked-by: Thomas Sailer <sailer@ife.ee.ethz.ch>
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Set the SNDRV_PCM_INFO_SYNC_START flag and the substream's sync ID
(only) if the substream actually can be linked to another one.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Don't use request_firmware() if the internal firmwares are defined
via Kconfig. Otherwise it results in a significant delay at loading
time (minutes).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Some drivers are already ifdefs for enabling external firmwares
but not defined in Kconfig. Now they appear as the kernel configs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Clean up maestro3 amp and GPIO quirks using snd_pci_quirk_lookup().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Load the ASSP codes using request_firmware(), if possible, instead of
using the built-in blobs.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fix IRQ flags for PCI devices.
The shared IRQs for PCI devices shouldn't be allocated with
IRQF_DISABLED. Also, when MSI is enabled, IRQF_SHARED shouldn't
be used.
The patch removes unnecessary cast in request_irq and free_irq,
too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
- Check the return value of pci_enable_device() and request_irq()
in the suspend. If any error occurs there, disable the device
using snd_card_disconnect().
- Call pci_set_power_state() properly with pci_choose_state().
- Fix the order to call pci_set_power_state().
- Removed obsolete house-made PM codes in some drivers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
Fixed 'section mismatch' errors in ALSA PCI drivers:
- removed invalid __devinitdata from pci id tables
- fix/remove __devinit of functions called in suspend/resume
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Change the 5th argument of snd_mpu401_uart_new() to bit flags
instead of a boolean. The argument takes bits that consist of
MPU401_INFO_XXX flags.
The callers that used the value 1 there are replaced with
MPU401_INFO_INTEGRATED.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There's no reason for #include'ing linux/dma-mapping.h more than once.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- fix brown-paper-bag locking bug (lock() / return / unlock())
- improve central function snd_m3_update_ptr()
(avoid expensive integer divisions)
- add cpu_relax() to busy-wait I/O loop as recommended
(does this require special macro support in ALSA for older kernels??)
- constify several structs
- spelling updates
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace all occurences of 0xff.. in calls to function pci_set_dma_mask()
and pci_set_consistant_dma_mask() with the corresponding DMA_xBIT_MASK from
linux/dma-mapping.h.
Signed-off-by: Matthias Gehre <M.Gehre@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch introduces the DMA_28BIT_MASK constant in dma-mapping.h
ALSA drivers using this mask are changed to use the new constant.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Jaroslav Kysela <perex@suse.cz>
Use schedule_timeout_{,un}interruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size. Also use
human-time conversion functions instead of hard-coded division to avoid
rounding issues.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Maestro3 driver
This patch fixes the maestro3 driver to call the snd_m3_assp_init
function to write the DSP firmware into the ASSP chip before sending the
RUN_ASSP command, thereby solving the hang after a cold boot.
Signed-off-by: Charles R. Anderson <cra@alum.wpi.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
`gcc -W' likes to complain if the static keyword is not at the beginning of
the declaration. This patch fixes all remaining occurrences of "inline
static" up with "static inline" in the entire kernel tree (140 occurrences in
47 files).
While making this change I came across a few lines with trailing whitespace
that I also fixed up, I have also added or removed a blank line or two here
and there, but there are no functional changes in the patch.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Maestro3 driver
Add a hardware volume quirk list to the maestro3 driver. Details were
taken from the Windows driver. Hardware volume control is enabled only for
the systems in the list.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Maestro3 driver
Some HP OmniBook laptops (500 and 6000 at least) require some GPIO magic
before the HW volume buttons work. This patch makes them work mostly.
Something is still missing to make them work perfectly. However I have been
unable to figure out what exactly.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Maestro3 driver
Due to a typo interrupts were never actually acked or disabled.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Alexey Dobriyan