Don't dereference simple_dai before it has been checked for NULL.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 1e974e5b82 ("ASoC: audio_graph_card2: Add support for variable slot widths")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220404113252.1152659-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Playback or capture errors are seen when clock is reset during an active
stage of DAI. Presently this scenario happens when DAI has both playback
and capture sessions running and one of these finishes first which will
be followed by clock rate reset. The remaining active session will be
affected in such case.
Address this problem by allowing clock rate reset to happen only when
the DAI is no more active.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/1646910999-2501-1-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some audio hardware cannot support the same slot width for all sample
widths, or a slot width equal to the sample width for all sample widths.
This is usually due either to limitations of the audio serial port or
system clocking restrictions.
A typical example would be:
- 16-bit samples in 16-bit slots
- 24-bit samples in 32-bit slots
The new dai-tdm-slot-width-map property allows setting a mapping of
sample widths and the corresponding tdm slot widths and slot counts.
Although the slot count is usually the same for all cases this does
allow for adding padding slots to maintain the same bitclk frequency.
The property is added to each endpoint node that needs the component
DAI to be told the TDM slot width and count.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220228172754.453783-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a new system-clock-fixed flag, which can be used to specify that the
driver cannot or should not allow the clock frequency of the mapped clock
to be modified. This behavior is also implied if the system-clock-frequency
parameter is set explicitly - the flag is meant for cases where a clock is
mapped to the DAI but which is, or should be treated as, fixed.
When mclk-fs is also specified, this causes a PCM constraint to be added
which enforces that only the corresponding valid sample rate can be used.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220120195832.1742271-7-robert.hancock@calian.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If an mclk-fs value was provided in the device tree configuration, the
calculated MCLK was fed into the downstream codec DAI and CPU DAI,
however set_sysclk was not being called on the platform device. Some
platform devices such as the Xilinx Audio Formatter need to know the MCLK
as well.
Call snd_soc_component_set_sysclk on each component in the stream to set
the proper sysclk value in addition to the existing call of
snd_soc_dai_set_sysclk on the codec DAI and CPU DAI. This may end up
resulting in redundant calls if one of the snd_soc_dai_set_sysclk calls
ends up calling snd_soc_component_set_sysclk itself, but that isn't
expected to cause any significant harm.
Fixes: f48dcbb6d4 ("ASoC: simple-card-utils: share asoc_simple_hw_param()")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20220120195832.1742271-5-robert.hancock@calian.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The ASoC core already has several helpers to parse card properties
from the device tree. Move the parsing code for "pin-switches" from
simple-card-utils to a shared snd_soc_of_parse_pin_switches() function
so other drivers can also use it to set up pin switches configured in
the device tree.
Cc: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20211214142049.20422-2-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
audio-graph-card2 will support DPCM/Multi/Codec2Codec,
and these will use almost same DT settings which uses
ports0 and ports1.
This patch adds asoc_graph_is_ports0() which checks
port is under port0 or not.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/875yu2n8ra.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The allocation of the DAI link components (DLCs) passed the wrong
pointer to sizeof. Since simple_dai_props is much larger than
snd_soc_dai_link_component, there was no out of bounds access, only
wasted memory.
Fixes: f2138aed23 ("ASoC: simple-card-utils: enable flexible CPU/Codec/Platform")
Fixes: 050c7950fd ("ASoC: simple-card-utils: alloc dai_link information for CPU/Codec/Platform")
Reviewed-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20210805050706.46833-1-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch switch to use snd_soc_daifmt_parse_format/clock_provider() from
snd_soc_of_parse_daifmt().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/871r95w9ch.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
audio-graph-card2 can reuse audio_graph_remove() / asoc_simple_remove().
This patch moves it to simple-card-utils.c.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87y2df3uby.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
audio-graph-card2 can reuse audio_graph_card_probe().
This patch moves it to simple-card-utils.c.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87zgxv3uc4.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current asoc_simple_canonicalize_cpu/platform() is assuming single CPU,
single Platform, but we want to support Multi support.
This patch is prepare for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87im4swf8y.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC is now supporting multi DAI, but, current
simple-card / audio-graph are assuming fixed single DAI.
This patch cares multi DAI at asoc_simple_clean_reference()
for of_node_put().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87o8ekwf9p.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC is now supporting multi DAI, but, current
simple-card / audio-graph are assuming fixed single DAI.
This patch uses for_each_prop_xxx() to support multi DAI.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87r1jgwf9y.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
li->dais is same as number of CPU + Codec,
li->conf is same as number of Codec when dummy-Codec.
li->dais/li->conf are no longer needed.
This patch removes these.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87sg3wwfa3.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We couldn't setup dai_props cpu_dai/codec_dai at the initial timing,
because "counting DAIs loop" and "detecting DAIs loop" were different.
But we can do it now, because these are using same loops.
This patch setups dai_props cpu_dai/codec_dai at the initial timing.
It can removes triky code from simple-card / audio-graph.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87tuocwfa8.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current simple-card / audio-graph creates 1xCPU + 1xCodec + 1xPlatform
for all dai_link, but some of them is not needed.
For example Platform is not needed for DPCM BE case.
Moreover, we can share snd-soc-dummy DAI for CPU-dummy / dummy-Codec
in DPCM.
This patch adds dummy DAI and share it when DPCM case,
I beliave it can contribute to reduce memory.
By this patch, CPU-dummy / dummy-CPU are set at asoc_simple_init_priv(),
thus, its settings are no longer needed at DPCM detecting timing
on simple-card / audio-graph.
Moreover, we can remove triky Platform settings code for DPCM BE,
because un-needed Platform is not created.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87tuoqod22.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current simple-card / audio-graph are assuming fixed
single-CPU/Codec/Platform.
This patch prepares multi-CPU/Codec/Platform support.
Note is that it is not yet full-multi-support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87v996od2c.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patchset tries to resolve the diversity in the audio LED
control among the ALSA drivers. A new control layer registration
is introduced which allows to run additional operations on
top of the elementary ALSA sound controls.
A new control access group (three bits in the access flags)
was introduced to carry the LED group information for
the sound controls. The low-level sound drivers can just
mark those controls using this access group. This information
is not exported to the user space, but user space can
manage the LED sound control associations through sysfs
(last patch) per Mark's request. It makes things fully
configurable in the kernel and user space (UCM).
The actual state ('route') evaluation is really easy
(the minimal value check for all channels / controls / cards).
If there's more complicated logic for a given hardware,
the card driver may eventually export a new read-only
sound control for the LED group and do the logic itself.
The new LED trigger control code is completely separated
and possibly optional (there's no symbol dependency).
The full code separation allows eventually to move this
LED trigger control to the user space in future.
Actually it replaces the already present functionality
in the kernel space (HDA drivers) and allows a quick adoption
for the recent hardware (ASoC codecs including SoundWire).
snd_ctl_led 24576 0
The sound driver implementation is really easy:
1) call snd_ctl_led_request() when control LED layer should be
automatically activated
/ it calls module_request("snd-ctl-led") on demand /
2) mark all related kcontrols with
SNDRV_CTL_ELEM_ACCESS_SPK_LED or
SNDRV_CTL_ELEM_ACCESS_MIC_LED
Link: https://lore.kernel.org/r/20210317172945.842280-1-perex@perex.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>
-----BEGIN PGP SIGNATURE-----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=1uM7
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmBkoFEACgkQJNaLcl1U
h9BqTgf5AUfR5NbQgJIUMtdMsuz+bthKGuPnpYhYzNUH0io9i3Sjpt0Mbw21dLp2
nXW+70BH0tJZBGR4DNGpmcpBLH5WPdOR9WIv4vCYy9Pr0uCGGKF/JkGeZAg7/llF
C3+yDfTnF0AvR+74xbf/LTjBPGja/08PED1ZC00NAkLhE3C0Pa/VQ0NaEtPUULWE
ZOWboF7hfQUeGzGPTqNp4Cy0/Pzokk6Fvl4kgfrxjNWO7ojIv9mCAvmYbusLW7NU
3Ph5VGsIuyMeorEoAVOFaBY2nrYG/mFZyzTNWJMgvF1MdeigMPNfbbffrUK0sn6k
e81zgWbwxboEujQ91/EZU7glIqtb6A==
=rr4V
-----END PGP SIGNATURE-----
Merge tag 'mute-led-rework' of https://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound into asoc-5.13
ALSA: control - add generic LED API
This patchset tries to resolve the diversity in the audio LED
control among the ALSA drivers. A new control layer registration
is introduced which allows to run additional operations on
top of the elementary ALSA sound controls.
A new control access group (three bits in the access flags)
was introduced to carry the LED group information for
the sound controls. The low-level sound drivers can just
mark those controls using this access group. This information
is not exported to the user space, but user space can
manage the LED sound control associations through sysfs
(last patch) per Mark's request. It makes things fully
configurable in the kernel and user space (UCM).
The actual state ('route') evaluation is really easy
(the minimal value check for all channels / controls / cards).
If there's more complicated logic for a given hardware,
the card driver may eventually export a new read-only
sound control for the LED group and do the logic itself.
The new LED trigger control code is completely separated
and possibly optional (there's no symbol dependency).
The full code separation allows eventually to move this
LED trigger control to the user space in future.
Actually it replaces the already present functionality
in the kernel space (HDA drivers) and allows a quick adoption
for the recent hardware (ASoC codecs including SoundWire).
snd_ctl_led 24576 0
The sound driver implementation is really easy:
1) call snd_ctl_led_request() when control LED layer should be
automatically activated
/ it calls module_request("snd-ctl-led") on demand /
2) mark all related kcontrols with
SNDRV_CTL_ELEM_ACCESS_SPK_LED or
SNDRV_CTL_ELEM_ACCESS_MIC_LED
Link: https://lore.kernel.org/r/20210317172945.842280-1-perex@perex.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>
simple-card / audio-graph are assuming single CPU/Codec/Platform on
dai_link. Because of it, it is difficult to support Multi-CPU/Codec.
This patch allocs CPU/Codec/Platform dai_link imformation
instead of using existing props information. It can update to
multi-CPU/Codec, but is still assuming single-CPU/Codec for now.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87blb61tpv.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
commit adb76b5b9c ("ASoC: soc-core: remove legacy style dai_link")
removed snd_soc_init_multicodec(). The comment on asoc_simple_init_priv()
is no longer needed. This patch removes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87czvm1tq2.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 1e30f642cf ("ASoC: simple-card-utils: Fix device
module clock"). The original patch ended up breaking following platform,
which depends on set_sysclk() to configure internal PLL on wm8904 codec
and expects simple-card-utils to not update the MCLK rate.
- "arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var3-ads2.dts"
It would be best if codec takes care of setting MCLK clock via DAI
set_sysclk() callback.
Reported-by: Michael Walle <michael@walle.cc>
Suggested-by: Mark Brown <broonie@kernel.org>
Suggested-by: Michael Walle <michael@walle.cc>
Fixes: 1e30f642cf ("ASoC: simple-card-utils: Fix device module clock")
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Tested-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/1615829492-8972-2-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/generic/simple-card-utils.c:258:10: style: Variable 'ret' is
assigned a value that is never used. [unreadVariable]
int ret = 0;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210218221921.88991-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If "clocks = <&xxx>" is specified from the CPU or Codec component
device node, the clock is not getting enabled. Thus audio playback
or capture fails.
Fix this by populating "simple_dai->clk" field when clocks property
is specified from device node as well. Also tidy up by re-organising
conditional statements of parsing logic.
Fixes: bb6fc620c2 ("ASoC: simple-card-utils: add asoc_simple_card_parse_clk()")
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/1612939421-19900-2-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the pin_name is fixed in asoc_simple_init_jack, but some driver
may use a different pin_name. So add a new parameter in
asoc_simple_init_jack for configuring pin_name.
If this parameter is NULL, then the default pin_name is used.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/1594822179-1849-2-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Following the example in cb2cf0de11 ("ASoC: soc-core: care Codec <->
Codec case by non_legacy_dai_naming"), determine if a DAI link contains
only codec DAIs by examining the non_legacy_dai_naming flag in each
DAI's component.
For now, we assume there is only one or a small set of valid PCM stream
parameters, so num_params == 1 is good enough. We also assume that the
same params are valid for all supported streams. params is set to the
subset of parameters common among all DAIs, and then the existing code
automatically chooses the highest quality of the remaining values when
the link is brought up.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20200305051143.60691-4-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch set 0Hz to sysclk when shutdown the card.
Some codecs set rate constraints that derives from sysclk. This
mechanism works correctly if machine drivers give fixed frequency.
But simple-audio and audio-graph card set variable clock rate if
'mclk-fs' property exists. In this case, rate constraints will go
bad scenario. For example a codec accepts three limited rates
(mclk / 256, mclk / 384, mclk / 512).
Bad scenario as follows (mclk-fs = 256):
- Initialize sysclk by correct value (Ex. 12.288MHz)
- Codec set constraints of PCM rate by sysclk
48kHz (1/256), 32kHz (1/384), 24kHz (1/512)
- Play 48kHz sound, it's acceptable
- Sysclk is not changed
- Play 32kHz sound, it's acceptable
- Set sysclk to 8.192MHz (= fs * mclk-fs = 32k * 256)
- Codec set constraints of PCM rate by sysclk
32kHz (1/256), 21.33kHz (1/384), 16kHz (1/512)
- Play 48kHz again, but it's NOT acceptable because constraints
do not allow 48kHz
So codecs treat 0Hz sysclk as signal of applying no constraints to
avoid this problem.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Link: https://lore.kernel.org/r/20190907174501.19833-1-katsuhiro@katsuster.net
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 3461473998 ("ASoC: soc-core: support dai_link with
platforms_num != 1") supports multi Platform, and
commit 9f3eb91753 ("ASoC: simple-card-utils: consider CPU-Platform
possibility") removed no Platform from simple-card.
Multi Platform is now checking both Platform name/of_node are NULL case.
But in normal case, DPCM be doesn't have Platform.
asoc_simple_canonicalize_platform() try to use CPU of_node
to Platform (This is needed for DMAEngine platform case),
but it still might be NULL at DPCM be.
This patch try to use no Platform after that if Platform of_node
is still NULL. It can't probe without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87muhmgw2o.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 6f04374457 ("ASoC: simple-card-utils: don't select unnecessary
Platform")
Current ALSA SoC avoid to add duplicate component to rtd,
and this driver was selecting CPU component as Platform component.
Thus, above patch removed Platform settings from this driver,
because it assumed these are same component.
But, some CPU driver is using generic DMAEngine, in such case, both
CPU component and Platform component will have same of_node/name.
In other words, there are some components which are different but
have same of_node/name.
In such case, Card driver definitely need to select Platform even
though it is same as CPU.
It is depends on CPU driver, but is difficult to know it from Card driver.
This patch reverts above patch.
Fixes: commit 6f04374457 ("ASoC: simple-card-utils: don't select unnecessary Platform")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA SoC is now supporting "no Platform". Sound card doesn't need to
select "CPU component" as "Platform" anymore if it doesn't need
special Platform.
This patch removes such settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC supports modern style dai_link (= snd_soc_dai_link_component) for
CPU. legacy style dai_link (= cpu_dai_name, cpu_name, cpu_of_node) are
no longer needed.
This patch switches to modern style.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This function is a helper that permits to create pin switch controls for
a list of widgets whose names are listed in the PREFIX "pin-switches"
devicetree property.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
sound/soc/generic/simple-card-utils.c: In function 'asoc_simple_parse_clk':
sound/soc/generic/simple-card-utils.c:164:18: warning:
parameter 'dai_name' set but not used [-Wunused-but-set-parameter]
It's not used since commit 0580dde594 ("ASoC: simple-card-utils: add
asoc_simple_debug_info()"), so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
li->conf will be 0 if it was not DPCM case.
Then, 1) we shouldn't call devm_kcalloc() with size 0,
2) we need NULL pointer check if li->conf was not 0.
This patch fixed above issues.
Special thanks to Pierre-Louis Bossart
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current simple-card-utils is using asoc_simple_card_xxx() for each
function naming, but it is very verbose.
Thus it is easy to be over 80 char.
This patch renames it to asoc_simple_xxx().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The difference between simple-card / audio-graph are just using
OF graph style, or not. In other words, other things should be same.
This means, simple-card/audio-graph common functions should be
implemented at simple-card-utils, and its own functions should be
implemented at each files.
Current simple-card / audio-graph are using
asoc_simple_card_parse_dai() which is different implementation.
But, these are implemanted at simple-card-utils.
It should be implemanted at each files.
This patch separate these into each files.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The difference between simple-card / audio-graph are just using
OF graph style, or not. In other words, other things should be same.
This means, simple-card/audio-graph common functions should be
implemented at simple-card-utils, and its own functions should be
implemented at each files.
Current simple-card / audio-graph are initializing each priv,
but it is same operation.
This patch adds new asoc_simple_card_init_priv() and initialize
priv by same operation.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The difference between simple-card / audio-graph are just using
OF graph style, or not. In other words, other things should be same.
This means, simple-card/audio-graph common functions should be
implemented at simple-card-utils, and its own functions should be
implemented at each files.
Current simple-card / audio-graph have almost same functions.
This patch shares asoc_simple_be_hw_params_fixup() between in these
2 drivers.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The difference between simple-card / audio-graph are just using
OF graph style, or not. In other words, other things should be same.
This means, simple-card/audio-graph common functions should be
implemented at simple-card-utils, and its own functions should be
implemented at each files.
Current simple-card / audio-graph have almost same functions.
This patch shares asoc_simple_dai_init() between in these 2 drivers.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The difference between simple-card / audio-graph are just using
OF graph style, or not. In other words, other things should be same.
This means, simple-card/audio-graph common functions should be
implemented at simple-card-utils, and its own functions should be
implemented at each files.
Current simple-card / audio-graph have almost same functions.
This patch shares asoc_simple_hw_param() between in these 2 drivers.
One note is that only simple-card supports simple_set_clk_rate()
at hw_param from commit e9be4ffd4f ("ASoC: simple-card: set cpu
dai clk in hw_params").
By this patch, audio-graph has same feature.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The difference between simple-card / audio-graph are just using
OF graph style, or not. In other words, other things should be same.
This means, simple-card/audio-graph common functions should be
implemented at simple-card-utils, and its own functions should be
implemented at each files.
Current simple-card / audio-graph have almost same functions.
This patch shares asoc_simple_shutdown() between in these 2 drivers.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The difference between simple-card / audio-graph are just using
OF graph style, or not. In other words, other things should be same.
This means, simple-card/audio-graph common functions should be
implemented at simple-card-utils, and its own functions should be
implemented at each files.
Current simple-card / audio-graph have almost same functions.
This patch shares asoc_simple_startup() between in these 2 drivers.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current simple-card-utils has dev_dbg(), but people want to
add #define DEBUG at simple-card/audio-graph, not simple-card-utils.
And, people want to get all information.
This patch adds new asoc_simple_debug_info() to indicates information.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current simple-card is using asoc_simple_card_canonicalize_dailink().
Its naming is "dailink", but is for "platform".
We already have asoc_simple_card_canonicalize_cpu() for "cpu",
let's follow same naming rule.
It never return error, so, void function is better idea.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Richard Fitzgerald