Add an inline helper function for getting an RX packet's
length or payload length and use it throughout the code
(most of which I did using an spatch.)
While at it, adjust some code, and remove a bogus comment
from the dvm calibration code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Calling stop_device when start_fw wasn't called would issue:
Stopping tx queues that aren't allocated...
Also allow the op_mode to call stop_device and then to
disable the Tx queues - in that case just silently ignore
the disabling on the Tx queues, since the PRPH registers
aren't reachable any more.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
It is not currently implemented for SDIO, and not required for other slave
buses as well.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Clear the FW_ERROR status before the common start_fw transport code.
Remove the transport specific clears.
After these patches the FW_ERROR flag is only set and cleared by common
transport code.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In case a sync command timeouts or Tx is stuck while a FW error
interrupt arrives, we might call iwl_op_mode_nic_error twice before
a restart has been initiated. This will cause a reprobe. Unify calls
to this function at the transport level and only call it on the first
FW error in a given by checking the transport FW error flag.
While at it, remove the privately defined iwl_nic_error from PCIE code
and use the common callback instead.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Stop Tx and commands from arriving to the transport layer when a FW
error has occurred. A HW recovery should take place before. Remove
transport specific checks of the same nature (note that not all
transports were protected).
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The same bits are employed in all transport layers. Put the status
field in the common transport layer. This allows us to employ them
in common transport code.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The stop_hw trans callback is not well defined. It is missing in many
cleanup flows and the division of labor between stop_device/stop_hw
is cumbersome. Remove stop_hw and use stop_device to perform both.
Implement this for all current transports.
PCIE needs some extra configuration the op-mode is leaving to configure
RF kill. Expose this explicitly as a new op_mode_leave trans callback.
Take the call to stop_device outside iwl_run_mvm_init_ucode, this
makes more sense and WARN when we want to run the INIT firmware while
it has run already.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The number of commands can never be negative, so it should
be using an unsigned type. This also shuts up an smatch
warning elsewhere in the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When we restart firmware and it is marked as not alive, we can still get
calls from mac80211. Don't WARN on in this situation as this triggers
automatic bug reports with no valuable information.
This continuation of:
commit 8ca95995e6
Author: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Date: Sun Sep 15 11:37:17 2013 +0300
iwlwifi: don't WARN on host commands sent when firmware is dead
which remove WARN_ONCE from one place, but those warnings are also
triggered from other functions.
Patch also adds unlikely() statement.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This triggers automatic bug reports and add no valuable
information. Print a simple error instead and drop the
host command.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no reason for the transport to call itself through
indirect function pointers, inline the (little) code there
is and remove the indirection completely.
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The old nl80211 testmode is no longer useful in iwlwifi,
we're moving towards a new model internally and there's
no open tool to use it, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For testing the D3 (WoWLAN) firmware, it is useful to be able
to run the firmware with instrumentation while the host isn't
sleeping and can poke at the firmware debug logging etc.
Implement this by a debugfs file. When the file is opened the
D3 firmware is loaded and all regular commands are blocked.
While the file is being read, poll the firmware's PME status
flag and report EOF once it changes to non-zero. When it is
closed, do (most of) the resume processing. This lets a user
just "cat" the file. Pressing Ctrl-C to kill the cat process
will resume the firwmare as though the platform resumed for
non-wireless reason and when the firmware wants to wake up
reading from the file automatically completes.
Unlike in real suspend, only disable interrupts and don't
reset the TX/RX hardware while in the test mode. This is a
workaround for some interrupt problems that happen only when
the PCIe link isn't fully reset (presumably by changing the
PCI config space registers which the core PCI code does.)
Note that while regular operations are blocked from sending
commands to the firmware, they could still be made and cause
strange mac80211 issues. Therefore, while using this testing
feature you need to be careful to not try to disconnect, roam
or similar, and will see warnings for such attempts.
Als note that this requires an upcoming firmware change to
tell the driver the location of the PME status flag in SRAM.
D3 test will fail if the firmware doesn't report the pointer.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If RF-kill is asserted while a device is initialized, the
firmware INIT image can now be run to retrieve the NVM
data and register to mac80211 properly. Previously, the
initialisation would fail in this scenario and the driver
wouldn't register with mac80211 at all, making the device
unusable.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using IWL_MVM_STATION_COUNT and IWL_INVALID_STATION together
isn't a good idea as they have different values. Always use
IWL_MVM_STATION_COUNT for an invalid station in MVM and move
the definition of the IWL_INVALID_STATION constant into the
DVM driver to avoid making such mistakes again. The one use
in the transport code can be hard-coded to -1 instead as the
station ID is passed as an integer there.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
7000.c was released as GPL only by mistake: it should be
dual licensed - GPL / BSD.
The file that contains the license in the kernel is COPYING
and not LICENSE.GPL.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the sequence number arithmetic code from mac80211 to
ieee80211.h so others can use it. Also rename the functions
from _seq to _sn, they operate on the sequence number, not
the sequence_control field.
Also move macros to convert the sequence control to/from
the sequence number value from various drivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Recently in commit 8a964f44e0
("iwlwifi: always copy first 16 bytes of commands") we fixed
the problem that the hardware writes back to the command and
that could overwrite parts of the data that was still needed
and would thus be corrupted.
Investigating this problem more closely we found that this
write-back isn't really ordered very well with respect to
other DMA traffic. Therefore, it sometimes happened that the
write-back occurred after unmapping the command again which
is clearly an issue and could corrupt the next allocation
that goes to that spot, or (better) cause IOMMU faults.
To fix this, allocate coherent memory for the first 16 bytes
of each command, containing the write-back part, and use it
for all queues. All the dynamic DMA mappings only need to be
TO_DEVICE then. This ensures that even when the write-back
happens "too late" it can't hit memory that has been freed
or a mapping that doesn't exist any more.
Since now the actual command is no longer modified, we can
also remove CMD_WANT_HCMD and get rid of the DMA sync that
was necessary to update the scratch pointer.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The IWL_MAX_CMD_TFDS name for this constant is wrong, the
constant really indicates how many TBs we can use in the
driver for a single command TFD, rename the constant and
also add a comment explaining it.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With new transports coming up, move to threaded
interrupt handling now. This has the advantage
that we can use the same locking scheme with all
different transports we may need to implement.
Note that the TX path obviously still runs in a
tasklet, so some spin_lock() calls need to change
to spin_lock_bh() calls to properly lock out the
TX path.
In my test on a Calpella platform this has no
impact on throughput or latency.
Also add lockdep annotations to avoid lockups due
to catch sending synchronous commands or using
locks that connect with them from the irq thread.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the reg_lock that protects HW register access
into the transport implementation. Locking is no
longer exposed, but handled internally in grab and
release NIC access. This simplifies the users.
Signed-off-by: Lilach Edelstein <lilach.edelstein@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Express iwl_set_bit() and iwl_clear_bit() through iwl_set_bits_mask()
and add the latter to the transport's API in order to allow different
implementation for different transport types in the future.
Signed-off-by: Lilach Edelstein <lilach.edelstein@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the pages are to be used by front-end, it may need
to know the page order, provide it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On resuming, the opmode may have to be able to talk
to the WoWLAN/D3 firmware in order to query it about
its status and wakeup reasons. To do that, the opmode
has to call the new d3_resume() transport API which
will set up the device for command communcation.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sending a NULL pointer to iwl_trans_write_mem allows now
to zero SRAM.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows to let sparse check that the NIC access is
always released.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Different transports implement the access to the SRAM in
different ways. Virtualize it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since different transports have different ways to wake the
up the NIC, we need to virtualize it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some cases, the fw should run even if the NIC is in
RFKILL. Make the API more flexible to allow that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
New transports may handle it internally for better performance.
Also move the tracing inside PRPH access which will make the
output more readable:
iwlwifi_dev_ioread_prph32: Read 0x0 from SCD_AGGR_SEL (32-bit)
instead of the corresponding accesses to HBUS_TARG_PRPH_*.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the op_mode is leaving, the transport should set
its pointer to it to NULL to not point to freed memory.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The ALIVE response of new fw inclues the base address of
the SCD in SRAM. Until we read it from a prph register,
which was set by the fw. Since the fw might well stop
updating the prph register, add a WARN when there is an
inconsitency between the ALIVE response and the register
to catch any change in the behavior.
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
No HCMD can be sent while RFKILL is asserted. If a SYNC
command is running while RFKILL is asserted the fw will
silently discard it. This means that the driver needs to
wake the process that sleeps on the CMD_SYNC.
Since the RFKILL interrupt is handled in the transport layer
and the code that sleeps in CMD_SYNC is also in the transport
layer, all this logic can be handled there.
This simplifies the work of the op_mode.
So the transport layer will now return -ERFKILL when a CMD
is sent and RFKILL is asserted. This will be the case even
when the CMD is SYNC. The transport layer will return
-ERFKILL straight away.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clarify the documentation to indicate that these
flags can only be used at the end, i.e. after them
a copy TFD (no flags set) is invalid.
Reported-by: Inbal Hacohen <inbal.hacohen@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In addition to the NOCOPY flag, add a DUP flag that
tells the transport to kmemdup() the buffer and free
it after the command completes.
Currently this is only supported for a single buffer
in a given command, but that could be extended if it
should be needed.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When tracing in iwlwifi, we get all data. Most of
the time, we don't need it, and it just takes up
a lot of extra space in the trace.
Make this optional by recording the data into two
separate trace events if it is needed. Without it,
record only the content of non-data and EAPOL TX
frames.
As a result, tracing without the data tracepoints
will record meta information including the 802.11
headers for all frames but will not record the
contents of data frames to reduce trace overhead.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Until now, the response handler of a Host Command got the
exact same pointer that was also given to the DMA engine.
We almost never need to the Host Command that was sent while
handling its response, but when we do need it, we see that
the command has been modified.
This mystery has been elucidated. The FH (our DMA engine)
writes its meta data on the buffer in the DRAM. Of course it
copies the buffer to the NIC first. This was known to happen
for Tx command, but as a matter of fact, it happens to all
TFD brought by the FH which doesn't care much about what it
brings from DRAM to internal SRAM.
So copy the Host Command to yet another buffer so that we
can properly pass the buffer that was sent originally to the
fw. Do that only if it was request by the user since very
few flows need to get the HCMD sent in the response handler.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The generic part of the driver now creates all debugfs
directories. It creates a root directory directly in
the the root of the debugfs filesystem and within that
directories for each device, named after the device ID
of the devices iwlwifi is attached to.
In the cfg80211/mac80211 directory there's now a link
to the toplevel iwlwifi debugfs directory to make it
easier to find the debugfs files.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the kmem cache API doesn't internally allocate
the name but just points to the name that was passed
in we can't use stack memory for it. Move the name
into the transport struct.
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the op_mode defines the queue mapping, let it do it
completely through the API functions.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Different transports will have different needs: New tranports
need headroom for their own use before the Tx cmd. So allocate
the Tx cmd pool in the transport and give it a unique name
based on dev_name.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg